Required properties:
- compatible : Should be "ti,omap3-l3-smx" for OMAP3 family
Should be "ti,omap4-l3-noc" for OMAP4 family
+- reg: Contains L3 register address range for each noc domain.
- ti,hwmods: "l3_main_1", ... One hwmod for each noc domain.
Examples:
OMAP Timer bindings
Required properties:
-- compatible: Must be "ti,omap2-timer" for OMAP2+ controllers.
+- compatible: Should be set to one of the below. Please note that
+ OMAP44xx devices have timer instances that are 100%
+ register compatible with OMAP3xxx devices as well as
+ newer timers that are not 100% register compatible.
+ So for OMAP44xx devices timer instances may use
+ different compatible strings.
+
+ ti,omap2420-timer (applicable to OMAP24xx devices)
+ ti,omap3430-timer (applicable to OMAP3xxx/44xx devices)
+ ti,omap4430-timer (applicable to OMAP44xx devices)
+ ti,omap5430-timer (applicable to OMAP543x devices)
+ ti,am335x-timer (applicable to AM335x devices)
+ ti,am335x-timer-1ms (applicable to AM335x devices)
+
- reg: Contains timer register address range (base address and
length).
- interrupts: Contains the interrupt information for the timer. The
Example:
timer12: timer@48304000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x48304000 0x400>;
interrupts = <95>;
ti,hwmods = "timer12"
--- /dev/null
+SAMSUNG S5P/Exynos SoC series System Registers (SYSREG)
+
+Properties:
+ - name : should be 'sysreg';
+ - compatible : should contain "samsung,<chip name>-sysreg", "syscon";
+ For Exynos4 SoC series it should be "samsung,exynos4-sysreg", "syscon";
+ - reg : offset and length of the register set.
Required properties:
- compatible : Should be "fsl,<chip>-dma-apbh" or "fsl,<chip>-dma-apbx"
- reg : Should contain registers location and length
+- interrupts : Should contain the interrupt numbers of DMA channels.
+ If a channel is empty/reserved, 0 should be filled in place.
+- #dma-cells : Must be <1>. The number cell specifies the channel ID.
+- dma-channels : Number of channels supported by the DMA controller
+
+Optional properties:
+- interrupt-names : Name of DMA channel interrupts
Supported chips:
imx23, imx28.
Examples:
-dma-apbh@80004000 {
+
+dma_apbh: dma-apbh@80004000 {
compatible = "fsl,imx28-dma-apbh";
- reg = <0x80004000 2000>;
+ reg = <0x80004000 0x2000>;
+ interrupts = <82 83 84 85
+ 88 88 88 88
+ 88 88 88 88
+ 87 86 0 0>;
+ interrupt-names = "ssp0", "ssp1", "ssp2", "ssp3",
+ "gpmi0", "gmpi1", "gpmi2", "gmpi3",
+ "gpmi4", "gmpi5", "gpmi6", "gmpi7",
+ "hsadc", "lcdif", "empty", "empty";
+ #dma-cells = <1>;
+ dma-channels = <16>;
};
-dma-apbx@80024000 {
+dma_apbx: dma-apbx@80024000 {
compatible = "fsl,imx28-dma-apbx";
- reg = <0x80024000 2000>;
+ reg = <0x80024000 0x2000>;
+ interrupts = <78 79 66 0
+ 80 81 68 69
+ 70 71 72 73
+ 74 75 76 77>;
+ interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+ "saif0", "saif1", "i2c0", "i2c1",
+ "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
+ "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
+ #dma-cells = <1>;
+ dma-channels = <16>;
+};
+
+DMA clients connected to the MXS DMA controller must use the format
+described in the dma.txt file.
+
+Examples:
+
+auart0: serial@8006a000 {
+ compatible = "fsl,imx28-auart", "fsl,imx23-auart";
+ reg = <0x8006a000 0x2000>;
+ interrupts = <112>;
+ dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+ dma-names = "rx", "tx";
};
imx23 and imx28.
- reg: Address and length of the register set for lcdif
- interrupts: Should contain lcdif interrupts
+- display : phandle to display node (see below for details)
-Optional properties:
-- panel-enable-gpios : Should specify the gpio for panel enable
+* display node
+
+Required properties:
+- bits-per-pixel : <16> for RGB565, <32> for RGB888/666.
+- bus-width : number of data lines. Could be <8>, <16>, <18> or <24>.
+
+Required sub-node:
+- display-timings : Refer to binding doc display-timing.txt for details.
Examples:
compatible = "fsl,imx28-lcdif";
reg = <0x80030000 2000>;
interrupts = <38 86>;
- panel-enable-gpios = <&gpio3 30 0>;
+
+ display: display {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33500000>;
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <164>;
+ hback-porch = <89>;
+ hsync-len = <10>;
+ vback-porch = <23>;
+ vfront-porch = <10>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
};
- "ti,omap2-gpio" for OMAP2 controllers
- "ti,omap3-gpio" for OMAP3 controllers
- "ti,omap4-gpio" for OMAP4 controllers
+- gpio-controller : Marks the device node as a GPIO controller.
- #gpio-cells : Should be two.
- first cell is the pin number
- second cell is used to specify optional parameters (unused)
-- gpio-controller : Marks the device node as a GPIO controller.
+- interrupt-controller: Mark the device node as an interrupt controller.
- #interrupt-cells : Should be 2.
-- interrupt-controller: Mark the device node as an interrupt controller
The first cell is the GPIO number.
The second cell is used to specify flags:
bits[3:0] trigger type and level flags:
gpio4: gpio4 {
compatible = "ti,omap4-gpio";
ti,hwmods = "gpio4";
- #gpio-cells = <2>;
gpio-controller;
- #interrupt-cells = <2>;
+ #gpio-cells = <2>;
interrupt-controller;
+ #interrupt-cells = <2>;
};
--- /dev/null
+* Samsung 2D Graphics Accelerator
+
+Required properties:
+ - compatible : value should be one among the following:
+ (a) "samsung,s5pv210-g2d" for G2D IP present in S5PV210 & Exynos4210 SoC
+ (b) "samsung,exynos4212-g2d" for G2D IP present in Exynos4x12 SoCs
+ (c) "samsung,exynos5250-g2d" for G2D IP present in Exynos5250 SoC
+
+ - reg : Physical base address of the IP registers and length of memory
+ mapped region.
+
+ - interrupts : G2D interrupt number to the CPU.
+
+Example:
+ g2d@12800000 {
+ compatible = "samsung,s5pv210-g2d";
+ reg = <0x12800000 0x1000>;
+ interrupts = <0 89 0>;
+ status = "disabled";
+ };
Required properties:
- compatible: Should be "fsl,<chip>-i2c"
- reg: Should contain registers location and length
-- interrupts: Should contain ERROR and DMA interrupts
+- interrupts: Should contain ERROR interrupt number
- clock-frequency: Desired I2C bus clock frequency in Hz.
Only 100000Hz and 400000Hz modes are supported.
-- fsl,i2c-dma-channel: APBX DMA channel for the I2C
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+ and I2C DMA channel ID.
+ Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
Examples:
#size-cells = <0>;
compatible = "fsl,imx28-i2c";
reg = <0x80058000 2000>;
- interrupts = <111 68>;
+ interrupts = <111>;
clock-frequency = <100000>;
- fsl,i2c-dma-channel = <6>;
+ dmas = <&dma_apbx 6>;
+ dma-names = "rx-tx";
};
--- /dev/null
+NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver.
+
+Required properties:
+- compatible : should be:
+ "nvidia,tegra114-i2c"
+ "nvidia,tegra30-i2c"
+ "nvidia,tegra20-i2c"
+ "nvidia,tegra20-i2c-dvc"
+ Details of compatible are as follows:
+ nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C
+ controller. This only support master mode of I2C communication. Register
+ interface/offset and interrupts handling are different than generic I2C
+ controller. Driver of DVC I2C controller is only compatible with
+ "nvidia,tegra20-i2c-dvc".
+ nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support
+ master and slave mode of I2C communication. The i2c-tegra driver only
+ support master mode of I2C communication. Driver of I2C controller is
+ only compatible with "nvidia,tegra20-i2c".
+ nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is
+ very much similar to Tegra20 I2C controller with additional feature:
+ Continue Transfer Support. This feature helps to implement M_NO_START
+ as per I2C core API transfer flags. Driver of I2C controller is
+ compatible with "nvidia,tegra30-i2c" to enable the continue transfer
+ support. This is also compatible with "nvidia,tegra20-i2c" without
+ continue transfer support.
+ nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is
+ very much similar to Tegra30 I2C controller with some hardware
+ modification:
+ - Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and
+ fast-clk. Tegra114 has only one clock source called as div-clk and
+ hence clock mechanism is changed in I2C controller.
+ - Tegra30/Tegra20 I2C controller has enabled per packet transfer by
+ default and there is no way to disable it. Tegra114 has this
+ interrupt disable by default and SW need to enable explicitly.
+ Due to above changes, Tegra114 I2C driver makes incompatible with
+ previous hardware driver. Hence, tegra114 I2C controller is compatible
+ with "nvidia,tegra114-i2c".
+- reg: Should contain I2C controller registers physical address and length.
+- interrupts: Should contain I2C controller interrupts.
+- address-cells: Address cells for I2C device address.
+- size-cells: Size of the I2C device address.
+- clocks: Clock ID as per
+ Documentation/devicetree/bindings/clock/tegra<chip-id>.txt
+ for I2C controller.
+- clock-names: Name of the clock:
+ Tegra20/Tegra30 I2C controller: "div-clk and "fast-clk".
+ Tegra114 I2C controller: "div-clk".
+
+Example:
+
+ i2c@7000c000 {
+ compatible = "nvidia,tegra20-i2c";
+ reg = <0x7000c000 0x100>;
+ interrupts = <0 38 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 12>, <&tegra_car 124>;
+ clock-names = "div-clk", "fast-clk";
+ status = "disabled";
+ };
Required properties:
- compatible: Should be "fsl,<chip>-mmc". The supported chips include
imx23 and imx28.
-- interrupts: Should contain ERROR and DMA interrupts
-- fsl,ssp-dma-channel: APBH DMA channel for the SSP
+- interrupts: Should contain ERROR interrupt number
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+ and SSP DMA channel ID.
+ Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
Examples:
ssp0: ssp@80010000 {
compatible = "fsl,imx28-mmc";
reg = <0x80010000 2000>;
- interrupts = <96 82>;
- fsl,ssp-dma-channel = <0>;
+ interrupts = <96>;
+ dmas = <&dma_apbh 0>;
+ dma-names = "rx-tx";
bus-width = <8>;
};
- compatible : should be "fsl,<chip>-gpmi-nand"
- reg : should contain registers location and length for gpmi and bch.
- reg-names: Should contain the reg names "gpmi-nand" and "bch"
- - interrupts : The first is the DMA interrupt number for GPMI.
- The second is the BCH interrupt number.
- - interrupt-names : The interrupt names "gpmi-dma", "bch";
- - fsl,gpmi-dma-channel : Should contain the dma channel it uses.
+ - interrupts : BCH interrupt number.
+ - interrupt-names : Should be "bch".
+ - dmas: DMA specifier, consisting of a phandle to DMA controller node
+ and GPMI DMA channel ID.
+ Refer to dma.txt and fsl-mxs-dma.txt for details.
+ - dma-names: Must be "rx-tx".
Optional properties:
- nand-on-flash-bbt: boolean to enable on flash bbt option if not
#size-cells = <1>;
reg = <0x8000c000 2000>, <0x8000a000 2000>;
reg-names = "gpmi-nand", "bch";
- interrupts = <88>, <41>;
- interrupt-names = "gpmi-dma", "bch";
- fsl,gpmi-dma-channel = <4>;
+ interrupts = <41>;
+ interrupt-names = "bch";
+ dmas = <&dma_apbh 4>;
+ dma-names = "rx-tx";
partition@0 {
...
0: Disable the internal pull-up
1: Enable the internal pull-up
+Note that when enabling the pull-up, the internal pad keeper gets disabled.
+Also, some pins doesn't have a pull up, in that case, setting the fsl,pull-up
+will only disable the internal pad keeper.
+
Examples:
pinctrl@80018000 {
Required properties:
- compatible : "nvidia,tegra-audio-alc5632"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+ "pll_a" (The Tegra clock of that name),
+ "pll_a_out0" (The Tegra clock of that name),
+ "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
- nvidia,model : The user-visible name of this sound complex.
- nvidia,audio-routing : A list of the connections between audio components.
Each entry is a pair of strings, the first being the connection's sink,
nvidia,i2s-controller = <&tegra_i2s1>;
nvidia,audio-codec = <&alc5632>;
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
Required properties:
- compatible : "nvidia,tegra-audio-trimslice"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+ "pll_a" (The Tegra clock of that name),
+ "pll_a_out0" (The Tegra clock of that name),
+ "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
- nvidia,audio-codec : The phandle of the WM8903 audio codec
compatible = "nvidia,tegra-audio-trimslice";
nvidia,i2s-controller = <&tegra_i2s1>;
nvidia,audio-codec = <&codec>;
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
Required properties:
- compatible : "nvidia,tegra-audio-wm8753"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+ "pll_a" (The Tegra clock of that name),
+ "pll_a_out0" (The Tegra clock of that name),
+ "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
- nvidia,model : The user-visible name of this sound complex.
- nvidia,audio-routing : A list of the connections between audio components.
Each entry is a pair of strings, the first being the connection's sink,
nvidia,i2s-controller = <&i2s1>;
nvidia,audio-codec = <&wm8753>;
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
Required properties:
- compatible : "nvidia,tegra-audio-wm8903"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+ "pll_a" (The Tegra clock of that name),
+ "pll_a_out0" (The Tegra clock of that name),
+ "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
- nvidia,model : The user-visible name of this sound complex.
- nvidia,audio-routing : A list of the connections between audio components.
Each entry is a pair of strings, the first being the connection's sink,
nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
Required properties:
- compatible : "nvidia,tegra-audio-wm9712"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+ "pll_a" (The Tegra clock of that name),
+ "pll_a_out0" (The Tegra clock of that name),
+ "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
- nvidia,model : The user-visible name of this sound complex.
- nvidia,audio-routing : A list of the connections between audio components.
Each entry is a pair of strings, the first being the connection's sink,
"Mic", "MIC1";
nvidia,ac97-controller = <&ac97>;
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
Required properties:
- compatible: Should be "fsl,<soc>-spi", where soc is "imx23" or "imx28"
- reg: Offset and length of the register set for the device
-- interrupts: Should contain SSP interrupts (error irq first, dma irq second)
-- fsl,ssp-dma-channel: APBX DMA channel for the SSP
+- interrupts: Should contain SSP ERROR interrupt
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+ and SSP DMA channel ID.
+ Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
Optional properties:
- clock-frequency : Input clock frequency to the SPI block in Hz.
#size-cells = <0>;
compatible = "fsl,imx28-spi";
reg = <0x80010000 0x2000>;
- interrupts = <96 82>;
- fsl,ssp-dma-channel = <0>;
+ interrupts = <96>;
+ dmas = <&dma_apbh 0>;
+ dma-names = "rx-tx";
};
--- /dev/null
+Davinci SPI controller device bindings
+
+Required properties:
+- #address-cells: number of cells required to define a chip select
+ address on the SPI bus. Should be set to 1.
+- #size-cells: should be zero.
+- compatible:
+ - "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family
+ - "ti,da830-spi" for SPI used similar to that on DA8xx SoC family
+- reg: Offset and length of SPI controller register space
+- num-cs: Number of chip selects
+- ti,davinci-spi-intr-line: interrupt line used to connect the SPI
+ IP to the interrupt controller within the SoC. Possible values
+ are 0 and 1. Manual says one of the two possible interrupt
+ lines can be tied to the interrupt controller. Set this
+ based on a specifc SoC configuration.
+- interrupts: interrupt number mapped to CPU.
+- clocks: spi clk phandle
+
+Example of a NOR flash slave device (n25q032) connected to DaVinci
+SPI controller device over the SPI bus.
+
+spi0:spi@20BF0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "ti,dm6446-spi";
+ reg = <0x20BF0000 0x1000>;
+ num-cs = <4>;
+ ti,davinci-spi-intr-line = <0>;
+ interrupts = <338>;
+ clocks = <&clkspi>;
+
+ flash: n25q032@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p32";
+ spi-max-frequency = <25000000>;
+ reg = <0>;
+
+ partition@0 {
+ label = "u-boot-spl";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition@1 {
+ label = "test";
+ reg = <0x80000 0x380000>;
+ };
+ };
+};
imx23 and imx28.
- reg : Address and length of the register set for the device
- interrupts : Should contain the auart interrupt numbers
-
-Optional properties:
-- fsl,auart-dma-channel : The DMA channels, the first is for RX, the other
- is for TX. If you add this property, it also means that you
- will enable the DMA support for the auart.
- Note: due to the hardware bug in imx23(see errata : 2836),
- only the imx28 can enable the DMA support for the auart.
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+ and AUART DMA channel ID.
+ Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: "rx" for RX channel, "tx" for TX channel.
Example:
auart0: serial@8006a000 {
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006a000 0x2000>;
- interrupts = <112 70 71>;
- fsl,auart-dma-channel = <8 9>;
+ interrupts = <112>;
+ dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+ dma-names = "rx", "tx";
};
Note: Each auart port should have an alias correctly numbered in "aliases"
- reg: physical base address of the controller and length of memory mapped
region.
- interrupts: interrupt number to the cpu.
+ - clocks: from common clock binding: handle to usb clock.
+ - clock-names: from common clock binding: Shall be "usbhost".
Optional properties:
- samsung,vbus-gpio: if present, specifies the GPIO that
reg = <0x12110000 0x100>;
interrupts = <0 71 0>;
samsung,vbus-gpio = <&gpx2 6 1 3 3>;
+
+ clocks = <&clock 285>;
+ clock-names = "usbhost";
};
OHCI
- reg: physical base address of the controller and length of memory mapped
region.
- interrupts: interrupt number to the cpu.
+ - clocks: from common clock binding: handle to usb clock.
+ - clock-names: from common clock binding: Shall be "usbhost".
Example:
usb@12120000 {
compatible = "samsung,exynos4210-ohci";
reg = <0x12120000 0x100>;
interrupts = <0 71 0>;
+
+ clocks = <&clock 285>;
+ clock-names = "usbhost";
};
represents PERIPHERAL.
- power : Should be "50". This signifies the controller can supply upto
100mA when operating in host mode.
+ - usb-phy : the phandle for the PHY device
Optional properties:
- ctrl-module : phandle of the control module this glue uses to write to
--- /dev/null
+Device-Tree bindings for Samsung SoC display controller (FIMD)
+
+FIMD (Fully Interactive Mobile Display) is the Display Controller for the
+Samsung series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be one of the following
+ "samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
+ "samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
+ "samsung,s5p6440-fimd"; /* for S5P64X0 SoCs */
+ "samsung,s5pc100-fimd"; /* for S5PC100 SoC */
+ "samsung,s5pv210-fimd"; /* for S5PV210 SoC */
+ "samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
+ "samsung,exynos5250-fimd"; /* for Exynos5 SoCs */
+
+- reg: physical base address and length of the FIMD registers set.
+
+- interrupt-parent: should be the phandle of the fimd controller's
+ parent interrupt controller.
+
+- interrupts: should contain a list of all FIMD IP block interrupts in the
+ order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
+ format depends on the interrupt controller used.
+
+- interrupt-names: should contain the interrupt names: "fifo", "vsync",
+ "lcd_sys", in the same order as they were listed in the interrupts
+ property.
+
+- pinctrl-0: pin control group to be used for this controller.
+
+- pinctrl-names: must contain a "default" entry.
+
+- clocks: must include clock specifiers corresponding to entries in the
+ clock-names property.
+
+- clock-names: list of clock names sorted in the same order as the clocks
+ property. Must contain "sclk_fimd" and "fimd".
+
+Optional Properties:
+- samsung,power-domain: a phandle to FIMD power domain node.
+
+Example:
+
+SoC specific DT entry:
+
+ fimd@11c00000 {
+ compatible = "samsung,exynos4210-fimd";
+ interrupt-parent = <&combiner>;
+ reg = <0x11c00000 0x20000>;
+ interrupt-names = "fifo", "vsync", "lcd_sys";
+ interrupts = <11 0>, <11 1>, <11 2>;
+ clocks = <&clock 140>, <&clock 283>;
+ clock-names = "sclk_fimd", "fimd";
+ samsung,power-domain = <&pd_lcd0>;
+ status = "disabled";
+ };
+
+Board specific DT entry:
+
+ fimd@11c00000 {
+ pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
exynos4412-smdk4412.dtb \
exynos4412-origen.dtb \
exynos5250-arndale.dtb \
+ exynos5440-sd5v1.dtb \
exynos5250-smdk5250.dtb \
exynos5250-snow.dtb \
exynos5440-ssdk5440.dtb
imx28-tx28.dtb
dtb-$(CONFIG_ARCH_NOMADIK) += ste-nomadik-s8815.dtb
dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
+ omap3430-sdp.dtb \
omap3-beagle.dtb \
+ omap3-devkit8000.dtb \
omap3-beagle-xm.dtb \
omap3-evm.dtb \
omap3-tobi.dtb \
+ omap3-igep0020.dtb \
+ omap3-igep0030.dtb \
omap4-panda.dtb \
omap4-panda-a4.dtb \
omap4-panda-es.dtb \
status = "okay";
};
- i2c1: i2c@44e0b000 {
+ i2c0: i2c@44e0b000 {
status = "okay";
clock-frequency = <400000>;
led@2 {
label = "beaglebone:green:heartbeat";
- gpios = <&gpio2 21 0>;
+ gpios = <&gpio1 21 0>;
linux,default-trigger = "heartbeat";
default-state = "off";
};
led@3 {
label = "beaglebone:green:mmc0";
- gpios = <&gpio2 22 0>;
+ gpios = <&gpio1 22 0>;
linux,default-trigger = "mmc0";
default-state = "off";
};
led@4 {
label = "beaglebone:green:usr2";
- gpios = <&gpio2 23 0>;
+ gpios = <&gpio1 23 0>;
default-state = "off";
};
led@5 {
label = "beaglebone:green:usr3";
- gpios = <&gpio2 24 0>;
+ gpios = <&gpio1 24 0>;
default-state = "off";
};
};
status = "okay";
};
- i2c1: i2c@44e0b000 {
+ i2c0: i2c@44e0b000 {
status = "okay";
clock-frequency = <400000>;
};
};
- i2c2: i2c@4802a000 {
+ i2c1: i2c@4802a000 {
status = "okay";
clock-frequency = <100000>;
debounce-delay-ms = <5>;
col-scan-delay-us = <2>;
- row-gpios = <&gpio2 25 0 /* Bank1, pin25 */
- &gpio2 26 0 /* Bank1, pin26 */
- &gpio2 27 0>; /* Bank1, pin27 */
+ row-gpios = <&gpio1 25 0 /* Bank1, pin25 */
+ &gpio1 26 0 /* Bank1, pin26 */
+ &gpio1 27 0>; /* Bank1, pin27 */
- col-gpios = <&gpio2 21 0 /* Bank1, pin21 */
- &gpio2 22 0>; /* Bank1, pin22 */
+ col-gpios = <&gpio1 21 0 /* Bank1, pin21 */
+ &gpio1 22 0>; /* Bank1, pin22 */
linux,keymap = <0x0000008b /* MENU */
0x0100009e /* BACK */
switch@9 {
label = "volume-up";
linux,code = <115>;
- gpios = <&gpio1 2 1>;
+ gpios = <&gpio0 2 1>;
gpio-key,wakeup;
};
switch@10 {
label = "volume-down";
linux,code = <114>;
- gpios = <&gpio1 3 1>;
+ gpios = <&gpio0 3 1>;
gpio-key,wakeup;
};
};
status = "okay";
};
- i2c1: i2c@44e0b000 {
+ i2c0: i2c@44e0b000 {
status = "okay";
clock-frequency = <400000>;
led@1 {
label = "evmsk:green:usr0";
- gpios = <&gpio2 4 0>;
+ gpios = <&gpio1 4 0>;
default-state = "off";
};
led@2 {
label = "evmsk:green:usr1";
- gpios = <&gpio2 5 0>;
+ gpios = <&gpio1 5 0>;
default-state = "off";
};
led@3 {
label = "evmsk:green:mmc0";
- gpios = <&gpio2 6 0>;
+ gpios = <&gpio1 6 0>;
linux,default-trigger = "mmc0";
default-state = "off";
};
led@4 {
label = "evmsk:green:heartbeat";
- gpios = <&gpio2 7 0>;
+ gpios = <&gpio1 7 0>;
linux,default-trigger = "heartbeat";
default-state = "off";
};
switch@1 {
label = "button0";
linux,code = <0x100>;
- gpios = <&gpio3 3 0>;
+ gpios = <&gpio2 3 0>;
};
switch@2 {
label = "button1";
linux,code = <0x101>;
- gpios = <&gpio3 2 0>;
+ gpios = <&gpio2 2 0>;
};
switch@3 {
label = "button2";
linux,code = <0x102>;
- gpios = <&gpio1 30 0>;
+ gpios = <&gpio0 30 0>;
gpio-key,wakeup;
};
switch@4 {
label = "button3";
linux,code = <0x103>;
- gpios = <&gpio3 5 0>;
+ gpios = <&gpio2 5 0>;
};
};
};
serial3 = &uart4;
serial4 = &uart5;
serial5 = &uart6;
+ d_can0 = &dcan0;
+ d_can1 = &dcan1;
};
cpus {
reg = <0x48200000 0x1000>;
};
- gpio1: gpio@44e07000 {
+ gpio0: gpio@44e07000 {
compatible = "ti,omap4-gpio";
ti,hwmods = "gpio1";
gpio-controller;
interrupts = <96>;
};
- gpio2: gpio@4804c000 {
+ gpio1: gpio@4804c000 {
compatible = "ti,omap4-gpio";
ti,hwmods = "gpio2";
gpio-controller;
interrupts = <98>;
};
- gpio3: gpio@481ac000 {
+ gpio2: gpio@481ac000 {
compatible = "ti,omap4-gpio";
ti,hwmods = "gpio3";
gpio-controller;
interrupts = <32>;
};
- gpio4: gpio@481ae000 {
+ gpio3: gpio@481ae000 {
compatible = "ti,omap4-gpio";
ti,hwmods = "gpio4";
gpio-controller;
status = "disabled";
};
- i2c1: i2c@44e0b000 {
+ i2c0: i2c@44e0b000 {
compatible = "ti,omap4-i2c";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
- i2c2: i2c@4802a000 {
+ i2c1: i2c@4802a000 {
compatible = "ti,omap4-i2c";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
- i2c3: i2c@4819c000 {
+ i2c2: i2c@4819c000 {
compatible = "ti,omap4-i2c";
#address-cells = <1>;
#size-cells = <0>;
dcan0: d_can@481cc000 {
compatible = "bosch,d_can";
ti,hwmods = "d_can0";
- reg = <0x481cc000 0x2000>;
+ reg = <0x481cc000 0x2000
+ 0x44e10644 0x4>;
interrupts = <52>;
status = "disabled";
};
dcan1: d_can@481d0000 {
compatible = "bosch,d_can";
ti,hwmods = "d_can1";
- reg = <0x481d0000 0x2000>;
+ reg = <0x481d0000 0x2000
+ 0x44e10644 0x4>;
interrupts = <55>;
status = "disabled";
};
timer1: timer@44e31000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,am335x-timer-1ms";
reg = <0x44e31000 0x400>;
interrupts = <67>;
ti,hwmods = "timer1";
};
timer2: timer@48040000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,am335x-timer";
reg = <0x48040000 0x400>;
interrupts = <68>;
ti,hwmods = "timer2";
};
timer3: timer@48042000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,am335x-timer";
reg = <0x48042000 0x400>;
interrupts = <69>;
ti,hwmods = "timer3";
};
timer4: timer@48044000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,am335x-timer";
reg = <0x48044000 0x400>;
interrupts = <92>;
ti,hwmods = "timer4";
};
timer5: timer@48046000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,am335x-timer";
reg = <0x48046000 0x400>;
interrupts = <93>;
ti,hwmods = "timer5";
};
timer6: timer@48048000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,am335x-timer";
reg = <0x48048000 0x400>;
interrupts = <94>;
ti,hwmods = "timer6";
};
timer7: timer@4804a000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,am335x-timer";
reg = <0x4804a000 0x400>;
interrupts = <95>;
ti,hwmods = "timer7";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x48030000 0x400>;
- interrupt = <65>;
+ interrupts = <65>;
ti,spi-num-cs = <2>;
ti,hwmods = "spi0";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x481a0000 0x400>;
- interrupt = <125>;
+ interrupts = <125>;
ti,spi-num-cs = <2>;
ti,hwmods = "spi1";
status = "disabled";
*/
/dts-v1/;
-/include/ "omap3.dtsi"
+/include/ "omap34xx.dtsi"
/ {
model = "TI AM3517 EVM (AM3517/05)";
*/
/dts-v1/;
-/include/ "omap3.dtsi"
+/include/ "omap34xx.dtsi"
/ {
model = "TeeJet Mt.Ventoux";
};
soc {
- serial@d0012000 {
- clock-frequency = <200000000>;
- status = "okay";
- };
- sata@d00a0000 {
- nr-ports = <2>;
- status = "okay";
- };
-
- mdio {
- phy0: ethernet-phy@0 {
- reg = <0>;
+ internal-regs {
+ serial@12000 {
+ clock-frequency = <200000000>;
+ status = "okay";
};
-
- phy1: ethernet-phy@1 {
- reg = <1>;
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
};
- };
- ethernet@d0070000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "rgmii-id";
- };
- ethernet@d0074000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "rgmii-id";
- };
+ mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
- mvsdio@d00d4000 {
- pinctrl-0 = <&sdio_pins1>;
- pinctrl-names = "default";
- /*
- * This device is disabled by default, because
- * using the SD card connector requires
- * changing the default CON40 connector
- * "DB-88F6710_MPP_2xRGMII_DEVICE_Jumper" to a
- * different connector
- * "DB-88F6710_MPP_RGMII_SD_Jumper".
- */
- status = "disabled";
- /* No CD or WP GPIOs */
- };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
- usb@d0050000 {
- status = "okay";
- };
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
- usb@d0051000 {
- status = "okay";
- };
+ mvsdio@d4000 {
+ pinctrl-0 = <&sdio_pins1>;
+ pinctrl-names = "default";
+ /*
+ * This device is disabled by default, because
+ * using the SD card connector requires
+ * changing the default CON40 connector
+ * "DB-88F6710_MPP_2xRGMII_DEVICE_Jumper" to a
+ * different connector
+ * "DB-88F6710_MPP_RGMII_SD_Jumper".
+ */
+ status = "disabled";
+ /* No CD or WP GPIOs */
+ };
- spi0: spi@d0010600 {
- status = "okay";
+ usb@50000 {
+ status = "okay";
+ };
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "mx25l25635e";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <50000000>;
+ usb@51000 {
+ status = "okay";
};
- };
- pcie-controller {
- status = "okay";
- /*
- * The two PCIe units are accessible through
- * both standard PCIe slots and mini-PCIe
- * slots on the board.
- */
- pcie@1,0 {
- /* Port 0, Lane 0 */
+ spi0: spi@10600 {
status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mx25l25635e";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+ };
};
- pcie@2,0 {
- /* Port 1, Lane 0 */
+
+ pcie-controller {
status = "okay";
+ /*
+ * The two PCIe units are accessible through
+ * both standard PCIe slots and mini-PCIe
+ * slots on the board.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie@2,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
};
};
};
};
soc {
- serial@d0012000 {
- clock-frequency = <200000000>;
- status = "okay";
- };
- timer@d0020300 {
- clock-frequency = <600000000>;
- status = "okay";
- };
-
- pinctrl {
- pwr_led_pin: pwr-led-pin {
- marvell,pins = "mpp63";
- marvell,function = "gpo";
+ internal-regs {
+ serial@12000 {
+ clock-frequency = <200000000>;
+ status = "okay";
};
-
- stat_led_pins: stat-led-pins {
- marvell,pins = "mpp64", "mpp65";
- marvell,function = "gpio";
+ timer@20300 {
+ clock-frequency = <600000000>;
+ status = "okay";
};
- };
- gpio_leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pwr_led_pin &stat_led_pins>;
+ pinctrl {
+ pwr_led_pin: pwr-led-pin {
+ marvell,pins = "mpp63";
+ marvell,function = "gpo";
+ };
- green_pwr_led {
- label = "mirabox:green:pwr";
- gpios = <&gpio1 31 1>;
- linux,default-trigger = "heartbeat";
+ stat_led_pins: stat-led-pins {
+ marvell,pins = "mpp64", "mpp65";
+ marvell,function = "gpio";
+ };
};
- blue_stat_led {
- label = "mirabox:blue:stat";
- gpios = <&gpio2 0 1>;
- linux,default-trigger = "cpu0";
+ gpio_leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_led_pin &stat_led_pins>;
+
+ green_pwr_led {
+ label = "mirabox:green:pwr";
+ gpios = <&gpio1 31 1>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ blue_stat_led {
+ label = "mirabox:blue:stat";
+ gpios = <&gpio2 0 1>;
+ linux,default-trigger = "cpu0";
+ };
+
+ green_stat_led {
+ label = "mirabox:green:stat";
+ gpios = <&gpio2 1 1>;
+ default-state = "off";
+ };
};
- green_stat_led {
- label = "mirabox:green:stat";
- gpios = <&gpio2 1 1>;
- default-state = "off";
- };
- };
+ mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
- mdio {
- phy0: ethernet-phy@0 {
- reg = <0>;
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
};
-
- phy1: ethernet-phy@1 {
- reg = <1>;
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
};
- };
- ethernet@d0070000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "rgmii-id";
- };
- ethernet@d0074000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "rgmii-id";
- };
-
- mvsdio@d00d4000 {
- pinctrl-0 = <&sdio_pins3>;
- pinctrl-names = "default";
- status = "okay";
- /*
- * No CD or WP GPIOs: SDIO interface used for
- * Wifi/Bluetooth chip
- */
- };
-
- usb@d0050000 {
- status = "okay";
- };
- usb@d0051000 {
- status = "okay";
- };
+ mvsdio@d4000 {
+ pinctrl-0 = <&sdio_pins3>;
+ pinctrl-names = "default";
+ status = "okay";
+ /*
+ * No CD or WP GPIOs: SDIO interface used for
+ * Wifi/Bluetooth chip
+ */
+ };
- i2c@d0011000 {
- status = "okay";
- clock-frequency = <100000>;
- pca9505: pca9505@25 {
- compatible = "nxp,pca9505";
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x25>;
+ usb@50000 {
+ status = "okay";
};
- };
- pcie-controller {
- status = "okay";
+ usb@51000 {
+ status = "okay";
+ };
- /* Internal mini-PCIe connector */
- pcie@1,0 {
- /* Port 0, Lane 0 */
+ i2c@11000 {
status = "okay";
+ clock-frequency = <100000>;
+ pca9505: pca9505@25 {
+ compatible = "nxp,pca9505";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x25>;
+ };
};
- /* Connected on the PCB to a USB 3.0 XHCI controller */
- pcie@2,0 {
- /* Port 1, Lane 0 */
+ pcie-controller {
status = "okay";
+
+ /* Internal mini-PCIe connector */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ /* Connected on the PCB to a USB 3.0 XHCI controller */
+ pcie@2,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
};
};
};
};
soc {
- serial@d0012000 {
- clock-frequency = <200000000>;
- status = "okay";
- };
- sata@d00a0000 {
- nr-ports = <2>;
- status = "okay";
- };
-
- mdio {
- phy0: ethernet-phy@0 {
- reg = <0>;
+ internal-regs {
+ serial@12000 {
+ clock-frequency = <200000000>;
+ status = "okay";
};
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+
+ mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
- phy1: ethernet-phy@1 {
- reg = <1>;
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
};
- };
- ethernet@d0070000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "sgmii";
- };
- ethernet@d0074000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "rgmii-id";
- };
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "sgmii";
+ };
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
- mvsdio@d00d4000 {
- pinctrl-0 = <&sdio_pins1>;
- pinctrl-names = "default";
- status = "okay";
- /* No CD or WP GPIOs */
- };
+ mvsdio@d4000 {
+ pinctrl-0 = <&sdio_pins1>;
+ pinctrl-names = "default";
+ status = "okay";
+ /* No CD or WP GPIOs */
+ };
- usb@d0050000 {
- status = "okay";
- };
+ usb@50000 {
+ status = "okay";
+ };
- usb@d0051000 {
- status = "okay";
- };
- };
+ usb@51000 {
+ status = "okay";
+ };
- gpio-keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- button@1 {
- label = "Software Button";
- linux,code = <116>;
- gpios = <&gpio0 6 1>;
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ button@1 {
+ label = "Software Button";
+ linux,code = <116>;
+ gpios = <&gpio0 6 1>;
+ };
+ };
};
};
-};
+ };
* 370 and Armada XP SoC.
*/
-/include/ "skeleton.dtsi"
+/include/ "skeleton64.dtsi"
/ {
model = "Marvell Armada 370 and XP SoC";
};
};
- mpic: interrupt-controller@d0020000 {
- compatible = "marvell,mpic";
- #interrupt-cells = <1>;
- #size-cells = <1>;
- interrupt-controller;
- };
-
- coherency-fabric@d0020200 {
- compatible = "marvell,coherency-fabric";
- reg = <0xd0020200 0xb0>,
- <0xd0021810 0x1c>;
- };
-
soc {
#address-cells = <1>;
#size-cells = <1>;
compatible = "simple-bus";
interrupt-parent = <&mpic>;
- ranges;
+ ranges = <0 0 0xd0000000 0x100000>;
+
+ internal-regs {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mpic: interrupt-controller@20000 {
+ compatible = "marvell,mpic";
+ #interrupt-cells = <1>;
+ #size-cells = <1>;
+ interrupt-controller;
+ };
+
+ coherency-fabric@20200 {
+ compatible = "marvell,coherency-fabric";
+ reg = <0x20200 0xb0>, <0x21810 0x1c>;
+ };
- serial@d0012000 {
+ serial@12000 {
compatible = "snps,dw-apb-uart";
- reg = <0xd0012000 0x100>;
+ reg = <0x12000 0x100>;
reg-shift = <2>;
interrupts = <41>;
reg-io-width = <1>;
status = "disabled";
- };
- serial@d0012100 {
+ };
+ serial@12100 {
compatible = "snps,dw-apb-uart";
- reg = <0xd0012100 0x100>;
+ reg = <0x12100 0x100>;
reg-shift = <2>;
interrupts = <42>;
reg-io-width = <1>;
status = "disabled";
- };
-
- timer@d0020300 {
- compatible = "marvell,armada-370-xp-timer";
- reg = <0xd0020300 0x30>,
- <0xd0021040 0x30>;
- interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
- clocks = <&coreclk 2>;
- };
-
- sata@d00a0000 {
- compatible = "marvell,orion-sata";
- reg = <0xd00a0000 0x2400>;
- interrupts = <55>;
- clocks = <&gateclk 15>, <&gateclk 30>;
- clock-names = "0", "1";
- status = "disabled";
- };
+ };
+
+ timer@20300 {
+ compatible = "marvell,armada-370-xp-timer";
+ reg = <0x20300 0x30>, <0x21040 0x30>;
+ interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
+ clocks = <&coreclk 2>;
+ };
+
+ sata@a0000 {
+ compatible = "marvell,orion-sata";
+ reg = <0xa0000 0x2400>;
+ interrupts = <55>;
+ clocks = <&gateclk 15>, <&gateclk 30>;
+ clock-names = "0", "1";
+ status = "disabled";
+ };
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "marvell,orion-mdio";
- reg = <0xd0072004 0x4>;
- };
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,orion-mdio";
+ reg = <0x72004 0x4>;
+ };
- ethernet@d0070000 {
+ ethernet@70000 {
compatible = "marvell,armada-370-neta";
- reg = <0xd0070000 0x2500>;
+ reg = <0x70000 0x2500>;
interrupts = <8>;
clocks = <&gateclk 4>;
status = "disabled";
- };
+ };
- ethernet@d0074000 {
+ ethernet@74000 {
compatible = "marvell,armada-370-neta";
- reg = <0xd0074000 0x2500>;
+ reg = <0x74000 0x2500>;
interrupts = <10>;
clocks = <&gateclk 3>;
status = "disabled";
- };
-
- i2c0: i2c@d0011000 {
- compatible = "marvell,mv64xxx-i2c";
- reg = <0xd0011000 0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <31>;
- timeout-ms = <1000>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- i2c1: i2c@d0011100 {
- compatible = "marvell,mv64xxx-i2c";
- reg = <0xd0011100 0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <32>;
- timeout-ms = <1000>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- rtc@10300 {
- compatible = "marvell,orion-rtc";
- reg = <0xd0010300 0x20>;
- interrupts = <50>;
- };
-
- mvsdio@d00d4000 {
- compatible = "marvell,orion-sdio";
- reg = <0xd00d4000 0x200>;
- interrupts = <54>;
- clocks = <&gateclk 17>;
- status = "disabled";
- };
-
- usb@d0050000 {
- compatible = "marvell,orion-ehci";
- reg = <0xd0050000 0x500>;
- interrupts = <45>;
- status = "disabled";
- };
-
- usb@d0051000 {
- compatible = "marvell,orion-ehci";
- reg = <0xd0051000 0x500>;
- interrupts = <46>;
- status = "disabled";
- };
-
- spi0: spi@d0010600 {
- compatible = "marvell,orion-spi";
- reg = <0xd0010600 0x28>;
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- interrupts = <30>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- spi1: spi@d0010680 {
- compatible = "marvell,orion-spi";
- reg = <0xd0010680 0x28>;
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- interrupts = <92>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- devbus-bootcs@d0010400 {
- compatible = "marvell,mvebu-devbus";
- reg = <0xd0010400 0x8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- devbus-cs0@d0010408 {
- compatible = "marvell,mvebu-devbus";
- reg = <0xd0010408 0x8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- devbus-cs1@d0010410 {
- compatible = "marvell,mvebu-devbus";
- reg = <0xd0010410 0x8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
+ };
+
+ i2c0: i2c@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <31>;
+ timeout-ms = <1000>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@11100 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11100 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <32>;
+ timeout-ms = <1000>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ rtc@10300 {
+ compatible = "marvell,orion-rtc";
+ reg = <0x10300 0x20>;
+ interrupts = <50>;
+ };
+
+ mvsdio@d4000 {
+ compatible = "marvell,orion-sdio";
+ reg = <0xd4000 0x200>;
+ interrupts = <54>;
+ clocks = <&gateclk 17>;
+ status = "disabled";
+ };
- devbus-cs2@d0010418 {
- compatible = "marvell,mvebu-devbus";
- reg = <0xd0010418 0x8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
+ usb@50000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x50000 0x500>;
+ interrupts = <45>;
+ status = "disabled";
+ };
- devbus-cs3@d0010420 {
- compatible = "marvell,mvebu-devbus";
- reg = <0xd0010420 0x8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&coreclk 0>;
- status = "disabled";
+ usb@51000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x51000 0x500>;
+ interrupts = <46>;
+ status = "disabled";
+ };
+
+ spi0: spi@10600 {
+ compatible = "marvell,orion-spi";
+ reg = <0x10600 0x28>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ interrupts = <30>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ spi1: spi@10680 {
+ compatible = "marvell,orion-spi";
+ reg = <0x10680 0x28>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ interrupts = <92>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ devbus-bootcs@10400 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <0x10400 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ devbus-cs0@10408 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <0x10408 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ devbus-cs1@10410 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <0x10410 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ devbus-cs2@10418 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <0x10418 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ devbus-cs3@10420 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <0x10420 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
};
};
-};
-
+ };
*/
/include/ "armada-370-xp.dtsi"
+/include/ "skeleton.dtsi"
/ {
model = "Marvell Armada 370 family SoC";
compatible = "marvell,armada370", "marvell,armada-370-xp";
- L2: l2-cache {
- compatible = "marvell,aurora-outer-cache";
- reg = <0xd0008000 0x1000>;
- cache-id-part = <0x100>;
- wt-override;
- };
aliases {
gpio0 = &gpio0;
gpio2 = &gpio2;
};
- mpic: interrupt-controller@d0020000 {
- reg = <0xd0020a00 0x1d0>,
- <0xd0021870 0x58>;
- };
-
soc {
- system-controller@d0018200 {
+ ranges = <0 0xd0000000 0x100000>;
+ internal-regs {
+ system-controller@18200 {
compatible = "marvell,armada-370-xp-system-controller";
- reg = <0xd0018200 0x100>;
- };
-
- pinctrl {
- compatible = "marvell,mv88f6710-pinctrl";
- reg = <0xd0018000 0x38>;
-
- sdio_pins1: sdio-pins1 {
- marvell,pins = "mpp9", "mpp11", "mpp12",
- "mpp13", "mpp14", "mpp15";
- marvell,function = "sd0";
+ reg = <0x18200 0x100>;
};
- sdio_pins2: sdio-pins2 {
- marvell,pins = "mpp47", "mpp48", "mpp49",
- "mpp50", "mpp51", "mpp52";
- marvell,function = "sd0";
+ L2: l2-cache {
+ compatible = "marvell,aurora-outer-cache";
+ reg = <0xd0008000 0x1000>;
+ cache-id-part = <0x100>;
+ wt-override;
};
- sdio_pins3: sdio-pins3 {
- marvell,pins = "mpp48", "mpp49", "mpp50",
- "mpp51", "mpp52", "mpp53";
- marvell,function = "sd0";
+ mpic: interrupt-controller@20000 {
+ reg = <0x20a00 0x1d0>, <0x21870 0x58>;
};
- };
-
- gpio0: gpio@d0018100 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018100 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <82>, <83>, <84>, <85>;
- };
-
- gpio1: gpio@d0018140 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018140 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <87>, <88>, <89>, <90>;
- };
-
- gpio2: gpio@d0018180 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018180 0x40>;
- ngpios = <2>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <91>;
- };
- coreclk: mvebu-sar@d0018230 {
- compatible = "marvell,armada-370-core-clock";
- reg = <0xd0018230 0x08>;
- #clock-cells = <1>;
- };
-
- gateclk: clock-gating-control@d0018220 {
- compatible = "marvell,armada-370-gating-clock";
- reg = <0xd0018220 0x4>;
- clocks = <&coreclk 0>;
- #clock-cells = <1>;
- };
-
- xor@d0060800 {
- compatible = "marvell,orion-xor";
- reg = <0xd0060800 0x100
- 0xd0060A00 0x100>;
- status = "okay";
-
- xor00 {
- interrupts = <51>;
- dmacap,memcpy;
- dmacap,xor;
+ pinctrl {
+ compatible = "marvell,mv88f6710-pinctrl";
+ reg = <0x18000 0x38>;
+
+ sdio_pins1: sdio-pins1 {
+ marvell,pins = "mpp9", "mpp11", "mpp12",
+ "mpp13", "mpp14", "mpp15";
+ marvell,function = "sd0";
+ };
+
+ sdio_pins2: sdio-pins2 {
+ marvell,pins = "mpp47", "mpp48", "mpp49",
+ "mpp50", "mpp51", "mpp52";
+ marvell,function = "sd0";
+ };
+
+ sdio_pins3: sdio-pins3 {
+ marvell,pins = "mpp48", "mpp49", "mpp50",
+ "mpp51", "mpp52", "mpp53";
+ marvell,function = "sd0";
+ };
};
- xor01 {
- interrupts = <52>;
- dmacap,memcpy;
- dmacap,xor;
- dmacap,memset;
- };
- };
-
- xor@d0060900 {
- compatible = "marvell,orion-xor";
- reg = <0xd0060900 0x100
- 0xd0060b00 0x100>;
- status = "okay";
- xor10 {
- interrupts = <94>;
- dmacap,memcpy;
- dmacap,xor;
+ gpio0: gpio@18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
};
- xor11 {
- interrupts = <95>;
- dmacap,memcpy;
- dmacap,xor;
- dmacap,memset;
- };
- };
- usb@d0050000 {
- clocks = <&coreclk 0>;
- };
-
- usb@d0051000 {
- clocks = <&coreclk 0>;
- };
+ gpio1: gpio@18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <87>, <88>, <89>, <90>;
+ };
- thermal@d0018300 {
- compatible = "marvell,armada370-thermal";
- reg = <0xd0018300 0x4
- 0xd0018304 0x4>;
- status = "okay";
- };
+ gpio2: gpio@18180 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18180 0x40>;
+ ngpios = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <91>;
+ };
- pcie-controller {
- compatible = "marvell,armada-370-pcie";
- status = "disabled";
- device_type = "pci";
+ coreclk: mvebu-sar@18230 {
+ compatible = "marvell,armada-370-core-clock";
+ reg = <0x18230 0x08>;
+ #clock-cells = <1>;
+ };
- #address-cells = <3>;
- #size-cells = <2>;
+ gateclk: clock-gating-control@18220 {
+ compatible = "marvell,armada-370-gating-clock";
+ reg = <0x18220 0x4>;
+ clocks = <&coreclk 0>;
+ #clock-cells = <1>;
+ };
- bus-range = <0x00 0xff>;
+ xor@60800 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60800 0x100
+ 0x60A00 0x100>;
+ status = "okay";
+
+ xor00 {
+ interrupts = <51>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor01 {
+ interrupts = <52>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
- reg = <0xd0040000 0x2000>, <0xd0080000 0x2000>;
+ xor@60900 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60900 0x100
+ 0x60b00 0x100>;
+ status = "okay";
+
+ xor10 {
+ interrupts = <94>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor11 {
+ interrupts = <95>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
- reg-names = "pcie0.0", "pcie1.0";
+ usb@50000 {
+ clocks = <&coreclk 0>;
+ };
- ranges = <0x82000000 0 0xd0040000 0xd0040000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0xd0080000 0xd0080000 0 0x00002000 /* Port 1.0 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
+ usb@51000 {
+ clocks = <&coreclk 0>;
+ };
- pcie@1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0040000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
+ thermal@18300 {
+ compatible = "marvell,armada370-thermal";
+ reg = <0x18300 0x4
+ 0x18304 0x4>;
+ status = "okay";
};
- pcie@2,0 {
+ pcie-controller {
+ compatible = "marvell,armada-370-pcie";
+ status = "disabled";
device_type = "pci";
- assigned-addresses = <0x82002800 0 0xd0080000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
+
#address-cells = <3>;
#size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 62>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 9>;
- status = "disabled";
+
+ bus-range = <0x00 0xff>;
+
+ reg = <0x40000 0x2000>, <0x80000 0x2000>;
+
+ reg-names = "pcie0.0", "pcie1.0";
+
+ ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
+ 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+ pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ pcie@2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 62>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 9>;
+ status = "disabled";
+ };
};
};
};
memory {
device_type = "memory";
- reg = <0x00000000 0x80000000>; /* 2 GB */
+ reg = <0 0x00000000 0 0x80000000>; /* 2 GB */
};
soc {
- serial@d0012000 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial@d0012100 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial@d0012200 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial@d0012300 {
- clock-frequency = <250000000>;
- status = "okay";
- };
-
- sata@d00a0000 {
- nr-ports = <2>;
- status = "okay";
- };
-
- mdio {
- phy0: ethernet-phy@0 {
- reg = <0>;
+ internal-regs {
+ serial@12000 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- phy1: ethernet-phy@1 {
- reg = <1>;
+ serial@12100 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- phy2: ethernet-phy@2 {
- reg = <25>;
+ serial@12200 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- phy3: ethernet-phy@3 {
- reg = <27>;
+ serial@12300 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
- };
-
- ethernet@d0070000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "rgmii-id";
- };
- ethernet@d0074000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "rgmii-id";
- };
- ethernet@d0030000 {
- status = "okay";
- phy = <&phy2>;
- phy-mode = "sgmii";
- };
- ethernet@d0034000 {
- status = "okay";
- phy = <&phy3>;
- phy-mode = "sgmii";
- };
-
- mvsdio@d00d4000 {
- pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
- status = "okay";
- /* No CD or WP GPIOs */
- };
- usb@d0050000 {
- status = "okay";
- };
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
- usb@d0051000 {
- status = "okay";
- };
+ mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
- usb@d0052000 {
- status = "okay";
- };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
- spi0: spi@d0010600 {
- status = "okay";
+ phy2: ethernet-phy@2 {
+ reg = <25>;
+ };
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "m25p64";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <20000000>;
+ phy3: ethernet-phy@3 {
+ reg = <27>;
+ };
};
- };
- pcie-controller {
- status = "okay";
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet@30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "sgmii";
+ };
+ ethernet@34000 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "sgmii";
+ };
- /*
- * All 6 slots are physically present as
- * standard PCIe slots on the board.
- */
- pcie@1,0 {
- /* Port 0, Lane 0 */
+ mvsdio@d4000 {
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-names = "default";
status = "okay";
+ /* No CD or WP GPIOs */
};
- pcie@2,0 {
- /* Port 0, Lane 1 */
+
+ usb@50000 {
status = "okay";
};
- pcie@3,0 {
- /* Port 0, Lane 2 */
+
+ usb@51000 {
status = "okay";
};
- pcie@4,0 {
- /* Port 0, Lane 3 */
+
+ usb@52000 {
status = "okay";
};
- pcie@9,0 {
- /* Port 2, Lane 0 */
+
+ spi0: spi@10600 {
status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+ };
};
- pcie@10,0 {
- /* Port 3, Lane 0 */
+
+ pcie-controller {
status = "okay";
+
+ /*
+ * All 6 slots are physically present as
+ * standard PCIe slots on the board.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie@2,0 {
+ /* Port 0, Lane 1 */
+ status = "okay";
+ };
+ pcie@3,0 {
+ /* Port 0, Lane 2 */
+ status = "okay";
+ };
+ pcie@4,0 {
+ /* Port 0, Lane 3 */
+ status = "okay";
+ };
+ pcie@9,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ pcie@10,0 {
+ /* Port 3, Lane 0 */
+ status = "okay";
+ };
};
};
};
memory {
device_type = "memory";
-
/*
- * 4 GB of plug-in RAM modules by default but only 3GB
- * are visible, the amount of memory available can be
- * changed by the bootloader according the size of the
- * module actually plugged
+ * 8 GB of plug-in RAM modules by default.The amount
+ * of memory available can be changed by the
+ * bootloader according the size of the module
+ * actually plugged. Only 7GB are usable because
+ * addresses from 0xC0000000 to 0xffffffff are used by
+ * the internal registers of the SoC.
*/
- reg = <0x00000000 0xC0000000>;
+ reg = <0x00000000 0x00000000 0x00000000 0xC0000000>,
+ <0x00000001 0x00000000 0x00000001 0x00000000>;
};
soc {
- serial@d0012000 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial@d0012100 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial@d0012200 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial@d0012300 {
- clock-frequency = <250000000>;
- status = "okay";
- };
-
- sata@d00a0000 {
- nr-ports = <2>;
- status = "okay";
- };
-
- mdio {
- phy0: ethernet-phy@0 {
- reg = <16>;
+ internal-regs {
+ serial@12000 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- phy1: ethernet-phy@1 {
- reg = <17>;
+ serial@12100 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- phy2: ethernet-phy@2 {
- reg = <18>;
+ serial@12200 {
+ clock-frequency = <250000000>;
+ status = "okay";
+ };
+ serial@12300 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
- phy3: ethernet-phy@3 {
- reg = <19>;
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
};
- };
- ethernet@d0070000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "rgmii-id";
- };
- ethernet@d0074000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "rgmii-id";
- };
- ethernet@d0030000 {
- status = "okay";
- phy = <&phy2>;
- phy-mode = "rgmii-id";
- };
- ethernet@d0034000 {
- status = "okay";
- phy = <&phy3>;
- phy-mode = "rgmii-id";
- };
+ mdio {
+ phy0: ethernet-phy@0 {
+ reg = <16>;
+ };
- spi0: spi@d0010600 {
- status = "okay";
+ phy1: ethernet-phy@1 {
+ reg = <17>;
+ };
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "n25q128a13";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <108000000>;
- };
- };
+ phy2: ethernet-phy@2 {
+ reg = <18>;
+ };
- devbus-bootcs@d0010400 {
- status = "okay";
- ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf000000, size 0x1000000 */
-
- /* Device Bus parameters are required */
-
- /* Read parameters */
- devbus,bus-width = <8>;
- devbus,turn-off-ps = <60000>;
- devbus,badr-skew-ps = <0>;
- devbus,acc-first-ps = <124000>;
- devbus,acc-next-ps = <248000>;
- devbus,rd-setup-ps = <0>;
- devbus,rd-hold-ps = <0>;
-
- /* Write parameters */
- devbus,sync-enable = <0>;
- devbus,wr-high-ps = <60000>;
- devbus,wr-low-ps = <60000>;
- devbus,ale-wr-ps = <60000>;
-
- /* NOR 16 MiB */
- nor@0 {
- compatible = "cfi-flash";
- reg = <0 0x1000000>;
- bank-width = <2>;
+ phy3: ethernet-phy@3 {
+ reg = <19>;
+ };
};
- };
- pcie-controller {
- status = "okay";
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet@30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet@34000 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "rgmii-id";
+ };
- /*
- * The 3 slots are physically present as
- * standard PCIe slots on the board.
- */
- pcie@1,0 {
- /* Port 0, Lane 0 */
+ spi0: spi@10600 {
status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a13";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ };
};
- pcie@9,0 {
- /* Port 2, Lane 0 */
+
+ devbus-bootcs@10400 {
status = "okay";
+ ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf000000, size 0x1000000 */
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <8>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+
+ /* NOR 16 MiB */
+ nor@0 {
+ compatible = "cfi-flash";
+ reg = <0 0x1000000>;
+ bank-width = <2>;
+ };
};
- pcie@10,0 {
- /* Port 3, Lane 0 */
+
+ pcie-controller {
status = "okay";
+
+ /*
+ * The 3 slots are physically present as
+ * standard PCIe slots on the board.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie@9,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ pcie@10,0 {
+ /* Port 3, Lane 0 */
+ status = "okay";
+ };
};
};
};
};
cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- device_type = "cpu";
- compatible = "marvell,sheeva-v7";
- reg = <0>;
- clocks = <&cpuclk 0>;
- };
-
- cpu@1 {
- device_type = "cpu";
- compatible = "marvell,sheeva-v7";
- reg = <1>;
- clocks = <&cpuclk 1>;
- };
- };
-
- soc {
- pinctrl {
- compatible = "marvell,mv78230-pinctrl";
- reg = <0xd0018000 0x38>;
-
- sdio_pins: sdio-pins {
- marvell,pins = "mpp30", "mpp31", "mpp32",
- "mpp33", "mpp34", "mpp35";
- marvell,function = "sd0";
- };
- };
-
- gpio0: gpio@d0018100 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018100 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <82>, <83>, <84>, <85>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <0>;
+ clocks = <&cpuclk 0>;
};
- gpio1: gpio@d0018140 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018140 0x40>;
- ngpios = <17>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <87>, <88>, <89>;
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <1>;
+ clocks = <&cpuclk 1>;
};
+ };
- /*
- * MV78230 has 2 PCIe units Gen2.0: One unit can be
- * configured as x4 or quad x1 lanes. One unit is
- * x4/x1.
- */
- pcie-controller {
- compatible = "marvell,armada-xp-pcie";
- status = "disabled";
- device_type = "pci";
-
- #address-cells = <3>;
- #size-cells = <2>;
-
- bus-range = <0x00 0xff>;
-
- ranges = <0x82000000 0 0xd0040000 0xd0040000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0xd0042000 0xd0042000 0 0x00002000 /* Port 2.0 registers */
- 0x82000000 0 0xd0044000 0xd0044000 0 0x00002000 /* Port 0.1 registers */
- 0x82000000 0 0xd0048000 0xd0048000 0 0x00002000 /* Port 0.2 registers */
- 0x82000000 0 0xd004c000 0xd004c000 0 0x00002000 /* Port 0.3 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
-
- pcie@1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0040000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
+ soc {
+ internal-regs {
+ pinctrl {
+ compatible = "marvell,mv78230-pinctrl";
+ reg = <0x18000 0x38>;
+
+ sdio_pins: sdio-pins {
+ marvell,pins = "mpp30", "mpp31", "mpp32",
+ "mpp33", "mpp34", "mpp35";
+ marvell,function = "sd0";
+ };
};
- pcie@2,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0044000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 59>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 6>;
- status = "disabled";
+ gpio0: gpio@18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
};
- pcie@3,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0048000 0 0x2000>;
- reg = <0x1800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 60>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 7>;
- status = "disabled";
+ gpio1: gpio@18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ ngpios = <17>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <87>, <88>, <89>;
};
- pcie@4,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd004c000 0 0x2000>;
- reg = <0x2000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 61>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 8>;
+ /*
+ * MV78230 has 2 PCIe units Gen2.0: One unit can be
+ * configured as x4 or quad x1 lanes. One unit is
+ * x4/x1.
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
status = "disabled";
- };
-
- pcie@9,0 {
device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0042000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
- status = "disabled";
+
+#address-cells = <3>;
+#size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
+ 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
+ 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
+ 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
+ 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+ pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ pcie@2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 59>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
+
+ pcie@3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 60>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 7>;
+ status = "disabled";
+ };
+
+ pcie@4,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+ reg = <0x2000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 61>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
+
+ pcie@9,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+ reg = <0x4800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 99>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 26>;
+ status = "disabled";
+ };
};
};
};
};
cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu@0 {
- device_type = "cpu";
- compatible = "marvell,sheeva-v7";
- reg = <0>;
- clocks = <&cpuclk 0>;
- };
-
- cpu@1 {
- device_type = "cpu";
- compatible = "marvell,sheeva-v7";
- reg = <1>;
- clocks = <&cpuclk 1>;
- };
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <0>;
+ clocks = <&cpuclk 0>;
+ };
+
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <1>;
+ clocks = <&cpuclk 1>;
+ };
};
soc {
- pinctrl {
- compatible = "marvell,mv78260-pinctrl";
- reg = <0xd0018000 0x38>;
-
- sdio_pins: sdio-pins {
- marvell,pins = "mpp30", "mpp31", "mpp32",
- "mpp33", "mpp34", "mpp35";
- marvell,function = "sd0";
+ internal-regs {
+ pinctrl {
+ compatible = "marvell,mv78260-pinctrl";
+ reg = <0x18000 0x38>;
+
+ sdio_pins: sdio-pins {
+ marvell,pins = "mpp30", "mpp31", "mpp32",
+ "mpp33", "mpp34", "mpp35";
+ marvell,function = "sd0";
+ };
};
- };
- gpio0: gpio@d0018100 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018100 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <82>, <83>, <84>, <85>;
- };
+ gpio0: gpio@18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
+ };
- gpio1: gpio@d0018140 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018140 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <87>, <88>, <89>, <90>;
- };
+ gpio1: gpio@18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <87>, <88>, <89>, <90>;
+ };
- gpio2: gpio@d0018180 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018180 0x40>;
- ngpios = <3>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <91>;
- };
+ gpio2: gpio@18180 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18180 0x40>;
+ ngpios = <3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <91>;
+ };
- ethernet@d0034000 {
+ ethernet@34000 {
compatible = "marvell,armada-370-neta";
- reg = <0xd0034000 0x2500>;
+ reg = <0x34000 0x2500>;
interrupts = <14>;
clocks = <&gateclk 1>;
status = "disabled";
- };
-
- /*
- * MV78260 has 3 PCIe units Gen2.0: Two units can be
- * configured as x4 or quad x1 lanes. One unit is
- * x4/x1.
- */
- pcie-controller {
- compatible = "marvell,armada-xp-pcie";
- status = "disabled";
- device_type = "pci";
-
- #address-cells = <3>;
- #size-cells = <2>;
-
- bus-range = <0x00 0xff>;
-
- ranges = <0x82000000 0 0xd0040000 0xd0040000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0xd0042000 0xd0042000 0 0x00002000 /* Port 2.0 registers */
- 0x82000000 0 0xd0044000 0xd0044000 0 0x00002000 /* Port 0.1 registers */
- 0x82000000 0 0xd0048000 0xd0048000 0 0x00002000 /* Port 0.2 registers */
- 0x82000000 0 0xd004c000 0xd004c000 0 0x00002000 /* Port 0.3 registers */
- 0x82000000 0 0xd0080000 0xd0080000 0 0x00002000 /* Port 1.0 registers */
- 0x82000000 0 0xd0082000 0xd0082000 0 0x00002000 /* Port 3.0 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
-
- pcie@1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0040000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
- };
-
- pcie@2,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0044000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 59>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 6>;
- status = "disabled";
};
- pcie@3,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0048000 0 0x2000>;
- reg = <0x1800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 60>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 7>;
+ /*
+ * MV78260 has 3 PCIe units Gen2.0: Two units can be
+ * configured as x4 or quad x1 lanes. One unit is
+ * x4/x1.
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
status = "disabled";
- };
-
- pcie@4,0 {
device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd004c000 0 0x2000>;
- reg = <0x2000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 61>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 8>;
- status = "disabled";
- };
- pcie@9,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0042000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
- status = "disabled";
- };
- pcie@10,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0082000 0 0x2000>;
- reg = <0x5000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 103>;
- marvell,pcie-port = <3>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 27>;
- status = "disabled";
+ bus-range = <0x00 0xff>;
+
+ ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
+ 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
+ 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
+ 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
+ 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
+ 0x82000000 0 0x82000 0x82000 0 0x00002000 /* Port 3.0 registers */
+ 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+ pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ pcie@2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 59>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
+
+ pcie@3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 60>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 7>;
+ status = "disabled";
+ };
+
+ pcie@4,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+ reg = <0x2000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 61>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
+
+ pcie@9,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+ reg = <0x4800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 99>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 26>;
+ status = "disabled";
+ };
+
+ pcie@10,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
+ reg = <0x5000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 103>;
+ marvell,pcie-port = <3>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 27>;
+ status = "disabled";
+ };
};
};
};
cpus {
- #address-cells = <1>;
- #size-cells = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
- cpu@0 {
- device_type = "cpu";
- compatible = "marvell,sheeva-v7";
- reg = <0>;
- clocks = <&cpuclk 0>;
- };
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <0>;
+ clocks = <&cpuclk 0>;
+ };
- cpu@1 {
- device_type = "cpu";
- compatible = "marvell,sheeva-v7";
- reg = <1>;
- clocks = <&cpuclk 1>;
- };
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <1>;
+ clocks = <&cpuclk 1>;
+ };
- cpu@2 {
- device_type = "cpu";
- compatible = "marvell,sheeva-v7";
- reg = <2>;
- clocks = <&cpuclk 2>;
- };
+ cpu@2 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <2>;
+ clocks = <&cpuclk 2>;
+ };
- cpu@3 {
- device_type = "cpu";
- compatible = "marvell,sheeva-v7";
- reg = <3>;
- clocks = <&cpuclk 3>;
- };
+ cpu@3 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <3>;
+ clocks = <&cpuclk 3>;
+ };
};
soc {
- pinctrl {
- compatible = "marvell,mv78460-pinctrl";
- reg = <0xd0018000 0x38>;
+ internal-regs {
+ pinctrl {
+ compatible = "marvell,mv78460-pinctrl";
+ reg = <0x18000 0x38>;
- sdio_pins: sdio-pins {
- marvell,pins = "mpp30", "mpp31", "mpp32",
- "mpp33", "mpp34", "mpp35";
- marvell,function = "sd0";
+ sdio_pins: sdio-pins {
+ marvell,pins = "mpp30", "mpp31", "mpp32",
+ "mpp33", "mpp34", "mpp35";
+ marvell,function = "sd0";
+ };
};
- };
- gpio0: gpio@d0018100 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018100 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <82>, <83>, <84>, <85>;
- };
+ gpio0: gpio@18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
+ };
- gpio1: gpio@d0018140 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018140 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <87>, <88>, <89>, <90>;
- };
+ gpio1: gpio@18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <87>, <88>, <89>, <90>;
+ };
- gpio2: gpio@d0018180 {
- compatible = "marvell,orion-gpio";
- reg = <0xd0018180 0x40>;
- ngpios = <3>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <91>;
- };
+ gpio2: gpio@18180 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18180 0x40>;
+ ngpios = <3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <91>;
+ };
- ethernet@d0034000 {
+ ethernet@34000 {
compatible = "marvell,armada-370-neta";
- reg = <0xd0034000 0x2500>;
+ reg = <0x34000 0x2500>;
interrupts = <14>;
clocks = <&gateclk 1>;
status = "disabled";
- };
+ };
- /*
- * MV78460 has 4 PCIe units Gen2.0: Two units can be
- * configured as x4 or quad x1 lanes. Two units are
- * x4/x1.
- */
- pcie-controller {
- compatible = "marvell,armada-xp-pcie";
- status = "disabled";
- device_type = "pci";
+ /*
+ * MV78460 has 4 PCIe units Gen2.0: Two units can be
+ * configured as x4 or quad x1 lanes. Two units are
+ * x4/x1.
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
+ status = "disabled";
+ device_type = "pci";
- #address-cells = <3>;
- #size-cells = <2>;
+ #address-cells = <3>;
+ #size-cells = <2>;
- bus-range = <0x00 0xff>;
+ bus-range = <0x00 0xff>;
- ranges = <0x82000000 0 0xd0040000 0xd0040000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0xd0042000 0xd0042000 0 0x00002000 /* Port 2.0 registers */
- 0x82000000 0 0xd0044000 0xd0044000 0 0x00002000 /* Port 0.1 registers */
- 0x82000000 0 0xd0048000 0xd0048000 0 0x00002000 /* Port 0.2 registers */
- 0x82000000 0 0xd004c000 0xd004c000 0 0x00002000 /* Port 0.3 registers */
- 0x82000000 0 0xd0080000 0xd0080000 0 0x00002000 /* Port 1.0 registers */
- 0x82000000 0 0xd0082000 0xd0082000 0 0x00002000 /* Port 3.0 registers */
- 0x82000000 0 0xd0084000 0xd0084000 0 0x00002000 /* Port 1.1 registers */
- 0x82000000 0 0xd0088000 0xd0088000 0 0x00002000 /* Port 1.2 registers */
- 0x82000000 0 0xd008c000 0xd008c000 0 0x00002000 /* Port 1.3 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
+ ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
+ 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
+ 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
+ 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
+ 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
+ 0x82000000 0 0x82000 0x82000 0 0x00002000 /* Port 3.0 registers */
+ 0x82000000 0 0x84000 0x84000 0 0x00002000 /* Port 1.1 registers */
+ 0x82000000 0 0x88000 0x88000 0 0x00002000 /* Port 1.2 registers */
+ 0x82000000 0 0x8c000 0x8c000 0 0x00002000 /* Port 1.3 registers */
+ 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
- pcie@1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0xd0040000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
- };
+ pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
- pcie@2,0 {
- device_type = "pci";
- assigned-addresses = <0x82001000 0 0xd0044000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 59>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 6>;
- status = "disabled";
- };
+ pcie@2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 59>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
- pcie@3,0 {
- device_type = "pci";
- assigned-addresses = <0x82001800 0 0xd0048000 0 0x2000>;
- reg = <0x1800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 60>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 7>;
- status = "disabled";
- };
+ pcie@3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 60>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 7>;
+ status = "disabled";
+ };
- pcie@4,0 {
- device_type = "pci";
- assigned-addresses = <0x82002000 0 0xd004c000 0 0x2000>;
- reg = <0x2000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 61>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 8>;
- status = "disabled";
- };
+ pcie@4,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
+ reg = <0x2000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 61>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
- pcie@5,0 {
- device_type = "pci";
- assigned-addresses = <0x82002800 0 0xd0080000 0 0x2000>;
- reg = <0x2800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 62>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 9>;
- status = "disabled";
- };
+ pcie@5,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+ reg = <0x2800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 62>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 9>;
+ status = "disabled";
+ };
- pcie@6,0 {
- device_type = "pci";
- assigned-addresses = <0x82003000 0 0xd0084000 0 0x2000>;
- reg = <0x3000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 63>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 10>;
- status = "disabled";
- };
+ pcie@6,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
+ reg = <0x3000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 63>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 10>;
+ status = "disabled";
+ };
- pcie@7,0 {
- device_type = "pci";
- assigned-addresses = <0x82003800 0 0xd0088000 0 0x2000>;
- reg = <0x3800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 64>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 11>;
- status = "disabled";
- };
+ pcie@7,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
+ reg = <0x3800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 64>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 11>;
+ status = "disabled";
+ };
- pcie@8,0 {
- device_type = "pci";
- assigned-addresses = <0x82004000 0 0xd008c000 0 0x2000>;
- reg = <0x4000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 65>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 12>;
- status = "disabled";
- };
- pcie@9,0 {
- device_type = "pci";
- assigned-addresses = <0x82004800 0 0xd0042000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
- status = "disabled";
- };
+ pcie@8,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
+ reg = <0x4000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 65>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 12>;
+ status = "disabled";
+ };
+ pcie@9,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
+ reg = <0x4800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 99>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 26>;
+ status = "disabled";
+ };
- pcie@10,0 {
- device_type = "pci";
- assigned-addresses = <0x82005000 0 0xd0082000 0 0x2000>;
- reg = <0x5000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 103>;
- marvell,pcie-port = <3>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 27>;
- status = "disabled";
+ pcie@10,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
+ reg = <0x5000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 103>;
+ marvell,pcie-port = <3>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 27>;
+ status = "disabled";
+ };
};
};
};
- };
+};
memory {
device_type = "memory";
- reg = <0x00000000 0xC0000000>; /* 3 GB */
+ reg = <0 0x00000000 0 0xC0000000>; /* 3 GB */
};
soc {
- serial@d0012000 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial@d0012100 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- pinctrl {
- led_pins: led-pins-0 {
- marvell,pins = "mpp49", "mpp51", "mpp53";
- marvell,function = "gpio";
+ internal-regs {
+ serial@12000 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
- };
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins>;
-
- red_led {
- label = "red_led";
- gpios = <&gpio1 17 1>;
- default-state = "off";
+ serial@12100 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- yellow_led {
- label = "yellow_led";
- gpios = <&gpio1 19 1>;
- default-state = "off";
+ pinctrl {
+ led_pins: led-pins-0 {
+ marvell,pins = "mpp49", "mpp51", "mpp53";
+ marvell,function = "gpio";
+ };
};
-
- green_led {
- label = "green_led";
- gpios = <&gpio1 21 1>;
- default-state = "off";
- linux,default-trigger = "heartbeat";
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ red_led {
+ label = "red_led";
+ gpios = <&gpio1 17 1>;
+ default-state = "off";
+ };
+
+ yellow_led {
+ label = "yellow_led";
+ gpios = <&gpio1 19 1>;
+ default-state = "off";
+ };
+
+ green_led {
+ label = "green_led";
+ gpios = <&gpio1 21 1>;
+ default-state = "off";
+ linux,default-trigger = "heartbeat";
+ };
};
- };
- gpio_keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
- button@1 {
- label = "Init Button";
- linux,code = <116>;
- gpios = <&gpio1 28 0>;
+ button@1 {
+ label = "Init Button";
+ linux,code = <116>;
+ gpios = <&gpio1 28 0>;
+ };
};
- };
- mdio {
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
+ mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
- phy2: ethernet-phy@2 {
- reg = <2>;
- };
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ };
- phy3: ethernet-phy@3 {
- reg = <3>;
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ };
};
- };
- ethernet@d0070000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "sgmii";
- };
- ethernet@d0074000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "sgmii";
- };
- ethernet@d0030000 {
- status = "okay";
- phy = <&phy2>;
- phy-mode = "sgmii";
- };
- ethernet@d0034000 {
- status = "okay";
- phy = <&phy3>;
- phy-mode = "sgmii";
- };
- i2c@d0011000 {
- status = "okay";
- clock-frequency = <400000>;
- };
- i2c@d0011100 {
- status = "okay";
- clock-frequency = <400000>;
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "sgmii";
+ };
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "sgmii";
+ };
+ ethernet@30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "sgmii";
+ };
+ ethernet@34000 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "sgmii";
+ };
+ i2c@11000 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+ i2c@11100 {
+ status = "okay";
+ clock-frequency = <400000>;
- s35390a: s35390a@30 {
- compatible = "s35390a";
- reg = <0x30>;
+ s35390a: s35390a@30 {
+ compatible = "s35390a";
+ reg = <0x30>;
+ };
+ };
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+ usb@50000 {
+ status = "okay";
+ };
+ usb@51000 {
+ status = "okay";
};
- };
- sata@d00a0000 {
- nr-ports = <2>;
- status = "okay";
- };
- usb@d0050000 {
- status = "okay";
- };
- usb@d0051000 {
- status = "okay";
- };
- devbus-bootcs@d0010400 {
- status = "okay";
- ranges = <0 0xf0000000 0x8000000>; /* @addr 0xf000000, size 0x8000000 */
-
- /* Device Bus parameters are required */
-
- /* Read parameters */
- devbus,bus-width = <8>;
- devbus,turn-off-ps = <60000>;
- devbus,badr-skew-ps = <0>;
- devbus,acc-first-ps = <124000>;
- devbus,acc-next-ps = <248000>;
- devbus,rd-setup-ps = <0>;
- devbus,rd-hold-ps = <0>;
-
- /* Write parameters */
- devbus,sync-enable = <0>;
- devbus,wr-high-ps = <60000>;
- devbus,wr-low-ps = <60000>;
- devbus,ale-wr-ps = <60000>;
-
- /* NOR 128 MiB */
- nor@0 {
- compatible = "cfi-flash";
- reg = <0 0x8000000>;
- bank-width = <2>;
+ devbus-bootcs@10400 {
+ status = "okay";
+ ranges = <0 0xf0000000 0x8000000>; /* @addr 0xf000000, size 0x8000000 */
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <8>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+
+ /* NOR 128 MiB */
+ nor@0 {
+ compatible = "cfi-flash";
+ reg = <0 0x8000000>;
+ bank-width = <2>;
+ };
};
- };
- pcie-controller {
- status = "okay";
- /* Internal mini-PCIe connector */
- pcie@1,0 {
- /* Port 0, Lane 0 */
+ pcie-controller {
status = "okay";
+ /* Internal mini-PCIe connector */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
};
};
};
model = "Marvell Armada XP family SoC";
compatible = "marvell,armadaxp", "marvell,armada-370-xp";
- L2: l2-cache {
- compatible = "marvell,aurora-system-cache";
- reg = <0xd0008000 0x1000>;
- cache-id-part = <0x100>;
- wt-override;
- };
+ soc {
+ internal-regs {
+ L2: l2-cache {
+ compatible = "marvell,aurora-system-cache";
+ reg = <0x08000 0x1000>;
+ cache-id-part = <0x100>;
+ wt-override;
+ };
- mpic: interrupt-controller@d0020000 {
- reg = <0xd0020a00 0x2d0>,
- <0xd0021070 0x58>;
- };
+ mpic: interrupt-controller@20000 {
+ reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+ };
- armada-370-xp-pmsu@d0022000 {
- compatible = "marvell,armada-370-xp-pmsu";
- reg = <0xd0022100 0x430>,
- <0xd0020800 0x20>;
- };
+ armada-370-xp-pmsu@22000 {
+ compatible = "marvell,armada-370-xp-pmsu";
+ reg = <0x22100 0x430>, <0x20800 0x20>;
+ };
- soc {
- serial@d0012200 {
+ serial@12200 {
compatible = "snps,dw-apb-uart";
- reg = <0xd0012200 0x100>;
+ reg = <0x12200 0x100>;
reg-shift = <2>;
interrupts = <43>;
reg-io-width = <1>;
status = "disabled";
- };
- serial@d0012300 {
+ };
+ serial@12300 {
compatible = "snps,dw-apb-uart";
- reg = <0xd0012300 0x100>;
+ reg = <0x12300 0x100>;
reg-shift = <2>;
interrupts = <44>;
reg-io-width = <1>;
status = "disabled";
- };
+ };
- timer@d0020300 {
+ timer@20300 {
marvell,timer-25Mhz;
- };
+ };
- coreclk: mvebu-sar@d0018230 {
- compatible = "marvell,armada-xp-core-clock";
- reg = <0xd0018230 0x08>;
- #clock-cells = <1>;
- };
+ coreclk: mvebu-sar@18230 {
+ compatible = "marvell,armada-xp-core-clock";
+ reg = <0x18230 0x08>;
+ #clock-cells = <1>;
+ };
- cpuclk: clock-complex@d0018700 {
- #clock-cells = <1>;
- compatible = "marvell,armada-xp-cpu-clock";
- reg = <0xd0018700 0xA0>;
- clocks = <&coreclk 1>;
- };
+ cpuclk: clock-complex@18700 {
+ #clock-cells = <1>;
+ compatible = "marvell,armada-xp-cpu-clock";
+ reg = <0x18700 0xA0>;
+ clocks = <&coreclk 1>;
+ };
- gateclk: clock-gating-control@d0018220 {
- compatible = "marvell,armada-xp-gating-clock";
- reg = <0xd0018220 0x4>;
- clocks = <&coreclk 0>;
- #clock-cells = <1>;
- };
+ gateclk: clock-gating-control@18220 {
+ compatible = "marvell,armada-xp-gating-clock";
+ reg = <0x18220 0x4>;
+ clocks = <&coreclk 0>;
+ #clock-cells = <1>;
+ };
- system-controller@d0018200 {
+ system-controller@18200 {
compatible = "marvell,armada-370-xp-system-controller";
- reg = <0xd0018200 0x500>;
- };
+ reg = <0x18200 0x500>;
+ };
- ethernet@d0030000 {
+ ethernet@30000 {
compatible = "marvell,armada-370-neta";
- reg = <0xd0030000 0x2500>;
+ reg = <0x30000 0x2500>;
interrupts = <12>;
clocks = <&gateclk 2>;
status = "disabled";
- };
-
- xor@d0060900 {
- compatible = "marvell,orion-xor";
- reg = <0xd0060900 0x100
- 0xd0060b00 0x100>;
- clocks = <&gateclk 22>;
- status = "okay";
-
- xor10 {
- interrupts = <51>;
- dmacap,memcpy;
- dmacap,xor;
- };
- xor11 {
- interrupts = <52>;
- dmacap,memcpy;
- dmacap,xor;
- dmacap,memset;
};
- };
- xor@d00f0900 {
- compatible = "marvell,orion-xor";
- reg = <0xd00F0900 0x100
- 0xd00F0B00 0x100>;
- clocks = <&gateclk 28>;
- status = "okay";
-
- xor00 {
- interrupts = <94>;
- dmacap,memcpy;
- dmacap,xor;
+ xor@60900 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60900 0x100
+ 0x60b00 0x100>;
+ clocks = <&gateclk 22>;
+ status = "okay";
+
+ xor10 {
+ interrupts = <51>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor11 {
+ interrupts = <52>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
};
- xor01 {
- interrupts = <95>;
- dmacap,memcpy;
- dmacap,xor;
- dmacap,memset;
+
+ xor@f0900 {
+ compatible = "marvell,orion-xor";
+ reg = <0xF0900 0x100
+ 0xF0B00 0x100>;
+ clocks = <&gateclk 28>;
+ status = "okay";
+
+ xor00 {
+ interrupts = <94>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor01 {
+ interrupts = <95>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
};
- };
- usb@d0050000 {
- clocks = <&gateclk 18>;
- };
+ usb@50000 {
+ clocks = <&gateclk 18>;
+ };
- usb@d0051000 {
- clocks = <&gateclk 19>;
- };
+ usb@51000 {
+ clocks = <&gateclk 19>;
+ };
- usb@d0052000 {
- compatible = "marvell,orion-ehci";
- reg = <0xd0052000 0x500>;
- interrupts = <47>;
- clocks = <&gateclk 20>;
- status = "disabled";
- };
+ usb@52000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x52000 0x500>;
+ interrupts = <47>;
+ clocks = <&gateclk 20>;
+ status = "disabled";
+ };
- thermal@d00182b0 {
- compatible = "marvell,armadaxp-thermal";
- reg = <0xd00182b0 0x4
- 0xd00184d0 0x4>;
- status = "okay";
+ thermal@182b0 {
+ compatible = "marvell,armadaxp-thermal";
+ reg = <0x182b0 0x4
+ 0x184d0 0x4>;
+ status = "okay";
+ };
};
};
};
chosen {
};
+ pinctrl@11400000 {
+ /*
+ * Disabled pullups since external part has its own pullups and
+ * double-pulling gets us out of spec in some cases.
+ */
+ i2c2_bus: i2c2-bus {
+ samsung,pin-pud = <0>;
+ };
+ };
+
i2c@12C60000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <378000>;
- gpios = <&gpb3 0 2 3 0>,
- <&gpb3 1 2 3 0>;
max77686@09 {
compatible = "maxim,max77686";
i2c@12C70000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <378000>;
- gpios = <&gpb3 2 2 3 0>,
- <&gpb3 3 2 3 0>;
};
i2c@12C80000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
- /*
- * Disabled pullups since external part has its own pullups and
- * double-pulling gets us out of spec in some cases.
- */
- gpios = <&gpa0 6 3 0 0>,
- <&gpa0 7 3 0 0>;
-
hdmiddc@50 {
compatible = "samsung,exynos5-hdmiddc";
reg = <0x50>;
i2c@12C90000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
- gpios = <&gpa1 2 3 3 0>,
- <&gpa1 3 3 3 0>;
};
i2c@12CA0000 {
- status = "disabled";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <66000>;
};
i2c@12CB0000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
- gpios = <&gpa2 2 3 3 0>,
- <&gpa2 3 3 3 0>;
};
i2c@12CC0000 {
i2c@12CD0000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
- gpios = <&gpb2 2 3 3 0>,
- <&gpb2 3 3 3 0>;
};
i2c@12CE0000 {
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
slot@0 {
reg = <0>;
bus-width = <8>;
- gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
- <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
- <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
- <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
- <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
};
};
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
slot@0 {
reg = <0>;
bus-width = <4>;
- samsung,cd-pinmux-gpio = <&gpc3 2 2 3 3>;
- wp-gpios = <&gpc2 1 0 0 3>;
- gpios = <&gpc3 0 2 0 3>, <&gpc3 1 2 0 3>,
- <&gpc3 3 2 3 3>, <&gpc3 4 2 3 3>,
- <&gpc3 5 2 3 3>, <&gpc3 6 2 3 3>;
+ wp-gpios = <&gpc2 1 0>;
};
};
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
+ /* See board-specific dts files for pin setup */
slot@0 {
reg = <0>;
bus-width = <4>;
- /* See board-specific dts files for GPIOs */
};
};
};
spi_1: spi@12d30000 {
- gpios = <&gpa2 4 2 3 0>,
- <&gpa2 6 2 3 0>,
- <&gpa2 7 2 3 0>;
samsung,spi-src-clk = <0>;
num-cs = <1>;
};
};
hdmi {
- hpd-gpio = <&gpx3 7 0xf 1 3>;
+ hpd-gpio = <&gpx3 7 0>;
};
gpio-keys {
power {
label = "Power";
- gpios = <&gpx1 3 0 0x10000 0>;
+ gpios = <&gpx1 3 1>;
linux,code = <116>; /* KEY_POWER */
gpio-key,wakeup;
};
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
};
+ spi1: spi@1f0e000 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins &spi1_cs0_pin>;
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ spi-max-frequency = <30000000>;
+ reg = <0>;
+ partition@0 {
+ label = "U-Boot-SPL";
+ reg = <0x00000000 0x00010000>;
+ read-only;
+ };
+ partition@1 {
+ label = "U-Boot";
+ reg = <0x00010000 0x00080000>;
+ read-only;
+ };
+ partition@2 {
+ label = "U-Boot-Env";
+ reg = <0x00090000 0x00010000>;
+ read-only;
+ };
+ partition@3 {
+ label = "Kernel";
+ reg = <0x000a0000 0x00280000>;
+ };
+ partition@4 {
+ label = "Filesystem";
+ reg = <0x00320000 0x00400000>;
+ };
+ partition@5 {
+ label = "MAC-Address";
+ reg = <0x007f0000 0x00010000>;
+ read-only;
+ };
+ };
+ };
};
nand_cs3@62000000 {
status = "okay";
0x28 0x00222222 0x00ffffff
>;
};
+ ehrpwm0a_pins: pinmux_ehrpwm0a_pins {
+ pinctrl-single,bits = <
+ /* EPWM0A */
+ 0xc 0x00000002 0x0000000f
+ >;
+ };
+ ehrpwm0b_pins: pinmux_ehrpwm0b_pins {
+ pinctrl-single,bits = <
+ /* EPWM0B */
+ 0xc 0x00000020 0x000000f0
+ >;
+ };
+ ehrpwm1a_pins: pinmux_ehrpwm1a_pins {
+ pinctrl-single,bits = <
+ /* EPWM1A */
+ 0x14 0x00000002 0x0000000f
+ >;
+ };
+ ehrpwm1b_pins: pinmux_ehrpwm1b_pins {
+ pinctrl-single,bits = <
+ /* EPWM1B */
+ 0x14 0x00000020 0x000000f0
+ >;
+ };
+ ecap0_pins: pinmux_ecap0_pins {
+ pinctrl-single,bits = <
+ /* ECAP0_APWM0 */
+ 0x8 0x20000000 0xf0000000
+ >;
+ };
+ ecap1_pins: pinmux_ecap1_pins {
+ pinctrl-single,bits = <
+ /* ECAP1_APWM1 */
+ 0x4 0x40000000 0xf0000000
+ >;
+ };
+ ecap2_pins: pinmux_ecap2_pins {
+ pinctrl-single,bits = <
+ /* ECAP2_APWM2 */
+ 0x4 0x00000004 0x0000000f
+ >;
+ };
+ spi1_pins: pinmux_spi_pins {
+ pinctrl-single,bits = <
+ /* SIMO, SOMI, CLK */
+ 0x14 0x00110100 0x00ff0f00
+ >;
+ };
+ spi1_cs0_pin: pinmux_spi1_cs0 {
+ pinctrl-single,bits = <
+ /* CS0 */
+ 0x14 0x00000010 0x000000f0
+ >;
+ };
};
serial0: serial@1c42000 {
compatible = "ns16550a";
interrupts = <16>;
status = "disabled";
};
+ ehrpwm0: ehrpwm@01f00000 {
+ compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x300000 0x2000>;
+ status = "disabled";
+ };
+ ehrpwm1: ehrpwm@01f02000 {
+ compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x302000 0x2000>;
+ status = "disabled";
+ };
+ ecap0: ecap@01f06000 {
+ compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+ #pwm-cells = <3>;
+ reg = <0x306000 0x80>;
+ status = "disabled";
+ };
+ ecap1: ecap@01f07000 {
+ compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+ #pwm-cells = <3>;
+ reg = <0x307000 0x80>;
+ status = "disabled";
+ };
+ ecap2: ecap@01f08000 {
+ compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+ #pwm-cells = <3>;
+ reg = <0x308000 0x80>;
+ status = "disabled";
+ };
+ spi1: spi@1f0e000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "ti,da830-spi";
+ reg = <0x30e000 0x1000>;
+ num-cs = <4>;
+ ti,davinci-spi-intr-line = <1>;
+ interrupts = <56>;
+ status = "disabled";
+ };
};
nand_cs3@62000000 {
compatible = "ti,davinci-nand";
i2c7 = &i2c_7;
};
+ chipid@10000000 {
+ compatible = "samsung,exynos4210-chipid";
+ reg = <0x10000000 0x100>;
+ };
+
pd_mfc: mfc-power-domain@10023C40 {
compatible = "samsung,exynos4210-pd";
reg = <0x10023C40 0x20>;
reg = <0x10440000 0x1000>;
};
+ sys_reg: sysreg {
+ compatible = "samsung,exynos4-sysreg", "syscon";
+ reg = <0x10010000 0x400>;
+ };
+
watchdog@10060000 {
compatible = "samsung,s3c2410-wdt";
reg = <0x10060000 0x100>;
interrupts = <0 58 0>;
clocks = <&clock 317>;
clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
status = "disabled";
};
interrupts = <0 59 0>;
clocks = <&clock 318>;
clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
status = "disabled";
};
#size-cells = <0>;
clocks = <&clock 327>, <&clock 159>;
clock-names = "spi", "spi_busclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_bus>;
status = "disabled";
};
#size-cells = <0>;
clocks = <&clock 328>, <&clock 160>;
clock-names = "spi", "spi_busclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_bus>;
status = "disabled";
};
#size-cells = <0>;
clocks = <&clock 329>, <&clock 161>;
clock-names = "spi", "spi_busclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_bus>;
status = "disabled";
};
#dma-requests = <1>;
};
};
+
+ fimd: fimd@11c00000 {
+ compatible = "samsung,exynos4210-fimd";
+ interrupt-parent = <&combiner>;
+ reg = <0x11c00000 0x20000>;
+ interrupt-names = "fifo", "vsync", "lcd_sys";
+ interrupts = <11 0>, <11 1>, <11 2>;
+ clocks = <&clock 140>, <&clock 283>;
+ clock-names = "sclk_fimd", "fimd";
+ samsung,power-domain = <&pd_lcd0>;
+ status = "disabled";
+ };
};
status = "okay";
};
+ g2d@12800000 {
+ status = "okay";
+ };
+
codec@13400000 {
samsung,mfc-r = <0x43000000 0x800000>;
samsung,mfc-l = <0x51000000 0x800000>;
};
sdhci@12530000 {
- samsung,sdhci-bus-width = <4>;
- linux,mmc_cap_4_bit_data;
- samsung,sdhci-cd-internal;
- gpio-cd = <&gpk2 2 2 3 3>;
- gpios = <&gpk2 0 2 0 3>,
- <&gpk2 1 2 0 3>,
- <&gpk2 3 2 3 3>,
- <&gpk2 4 2 3 3>,
- <&gpk2 5 2 3 3>,
- <&gpk2 6 2 3 3>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+ status = "okay";
+ };
+
+ g2d@12800000 {
status = "okay";
};
status = "okay";
};
+ pinctrl@11000000 {
+ keypad_rows: keypad-rows {
+ samsung,pins = "gpx2-0", "gpx2-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ keypad_cols: keypad-cols {
+ samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
+ "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+ };
+
keypad@100A0000 {
samsung,keypad-num-rows = <2>;
samsung,keypad-num-columns = <8>;
linux,keypad-no-autorepeat;
linux,keypad-wakeup;
+ pinctrl-names = "default";
+ pinctrl-0 = <&keypad_rows &keypad_cols>;
status = "okay";
- row-gpios = <&gpx2 0 3 3 0>,
- <&gpx2 1 3 3 0>;
-
- col-gpios = <&gpx1 0 3 0 0>,
- <&gpx1 1 3 0 0>,
- <&gpx1 2 3 0 0>,
- <&gpx1 3 3 0 0>,
- <&gpx1 4 3 0 0>,
- <&gpx1 5 3 0 0>,
- <&gpx1 6 3 0 0>,
- <&gpx1 7 3 0 0>;
-
key_1 {
keypad,row = <0>;
keypad,column = <3>;
#address-cells = <1>;
#size-cells = <0>;
samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <20000>;
- gpios = <&gpd1 0 2 3 0>,
- <&gpd1 1 2 3 0>;
+ samsung,i2c-max-bus-freq = <100000>;
status = "okay";
eeprom@50 {
};
spi_2: spi@13940000 {
- gpios = <&gpc1 1 5 3 0>,
- <&gpc1 3 5 3 0>,
- <&gpc1 4 5 3 0>;
status = "okay";
w25x80@0 {
spi-max-frequency = <1000000>;
controller-data {
- cs-gpio = <&gpc1 2 1 0 3>;
+ cs-gpio = <&gpc1 2 0>;
samsung,spi-feedback-delay = <0>;
};
reg = <0x100C0000 0x100>;
interrupts = <2 4>;
};
+
+ g2d@12800000 {
+ compatible = "samsung,s5pv210-g2d";
+ reg = <0x12800000 0x1000>;
+ interrupts = <0 89 0>;
+ status = "disabled";
+ };
};
status = "okay";
};
+ fimd@11c00000 {
+ pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing {
+ clock-frequency = <50000>;
+ hactive = <1024>;
+ vactive = <600>;
+ hfront-porch = <64>;
+ hback-porch = <16>;
+ hsync-len = <48>;
+ vback-porch = <64>;
+ vfront-porch = <16>;
+ vsync-len = <3>;
+ };
+ };
+
serial@13800000 {
status = "okay";
};
bootargs ="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC1,115200 init=/linuxrc";
};
+ g2d@10800000 {
+ status = "okay";
+ };
+
+ g2d@10800000 {
+ status = "okay";
+ };
+
sdhci@12530000 {
bus-width = <4>;
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
<0x7 0 &gic 1 12 0>;
};
};
+
+ mshc@12550000 {
+ compatible = "samsung,exynos4412-dw-mshc";
+ reg = <0x12550000 0x1000>;
+ interrupts = <0 77 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
reg = <0x106E0000 0x1000>;
interrupts = <0 72 0>;
};
+
+ g2d@10800000 {
+ compatible = "samsung,exynos4212-g2d";
+ reg = <0x10800000 0x1000>;
+ interrupts = <0 89 0>;
+ status = "disabled";
+ };
};
bootargs = "console=ttySAC2,115200";
};
+ codec@11000000 {
+ samsung,mfc-r = <0x43000000 0x800000>;
+ samsung,mfc-l = <0x51000000 0x800000>;
+ };
+
i2c@12C60000 {
- status = "disabled";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <20000>;
+ samsung,i2c-slave-addr = <0x66>;
+
+ s5m8767_pmic@66 {
+ compatible = "samsung,s5m8767-pmic";
+ reg = <0x66>;
+
+ s5m8767,pmic-buck2-dvs-voltage = <1300000>;
+ s5m8767,pmic-buck3-dvs-voltage = <1100000>;
+ s5m8767,pmic-buck4-dvs-voltage = <1200000>;
+ s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 0>,
+ <&gpd1 1 0>,
+ <&gpd1 2 0>;
+ s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>,
+ <&gpx2 4 0>,
+ <&gpx2 5 0>;
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_1.0V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDD_28IO_DP_1.35V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VDD_COMMON1_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDD_IOPERI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ op_mode = <1>;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VDD_EXT_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD_MPLL_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD_XPLL_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VDD_COMMON2_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "VDD_33ON_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ op_mode = <1>;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VDD_COMMON3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD_ABB2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD_USB_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VDDQ_C2C_W_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD18_ABB0_3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD10_COMMON4_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD18_HSIC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "VDDQ_MMC2_3_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "VDD_33ON_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ op_mode = <1>;
+ };
+
+ ldo22_reg: LDO22 {
+ regulator-name = "EXT_33_OFF";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ op_mode = <1>;
+ };
+
+ ldo23_reg: LDO23 {
+ regulator-name = "EXT_28_OFF";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ op_mode = <1>;
+ };
+
+ ldo25_reg: LDO25 {
+ regulator-name = "PVDD_LDO25";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ op_mode = <1>;
+ };
+
+ ldo26_reg: LDO26 {
+ regulator-name = "EXT_18_OFF";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ op_mode = <1>;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VDD_MEM_1.35V";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1355000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck9_reg: BUCK9 {
+ regulator-name = "VDD_33_OFF_EXT1";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <3000000>;
+ op_mode = <1>;
+ };
+ };
+ };
};
i2c@12C70000 {
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
+ vmmc-supply = <&mmc_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
slot@0 {
reg = <0>;
bus-width = <8>;
- gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
- <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
- <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>,
- <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
- <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>;
};
};
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
+ vmmc-supply = <&mmc_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
slot@0 {
reg = <0>;
bus-width = <4>;
- samsung,cd-pinmux-gpio = <&gpc3 2 2 3 3>;
- gpios = <&gpc3 0 2 0 3>, <&gpc3 1 2 0 3>,
- <&gpc3 3 2 3 3>, <&gpc3 4 2 3 3>,
- <&gpc3 5 2 3 3>, <&gpc3 6 2 3 3>;
+ disable-wp;
};
};
status = "disabled";
};
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ menu {
+ label = "SW-TACT2";
+ gpios = <&gpx1 4 1>;
+ linux,code = <139>;
+ gpio-key,wakeup;
+ };
+
+ home {
+ label = "SW-TACT3";
+ gpios = <&gpx1 5 1>;
+ linux,code = <102>;
+ gpio-key,wakeup;
+ };
+
+ up {
+ label = "SW-TACT4";
+ gpios = <&gpx1 6 1>;
+ linux,code = <103>;
+ gpio-key,wakeup;
+ };
+
+ down {
+ label = "SW-TACT5";
+ gpios = <&gpx1 7 1>;
+ linux,code = <108>;
+ gpio-key,wakeup;
+ };
+
+ back {
+ label = "SW-TACT6";
+ gpios = <&gpx2 0 1>;
+ linux,code = <158>;
+ gpio-key,wakeup;
+ };
+
+ wakeup {
+ label = "SW-TACT7";
+ gpios = <&gpx2 1 1>;
+ linux,code = <143>;
+ gpio-key,wakeup;
+ };
+ };
+
+ hdmi {
+ hpd-gpio = <&gpx3 7 2>;
+ vdd_osc-supply = <&ldo10_reg>;
+ vdd_pll-supply = <&ldo8_reg>;
+ vdd-supply = <&ldo8_reg>;
+ };
+
+ mmc_reg: voltage-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_33ON_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ gpio = <&gpx1 1 1>;
+ enable-active-high;
+ };
+
+ reg_hdmi_en: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "hdmi-en";
+ };
+
fixed-rate-clocks {
xxti {
compatible = "samsung,clock-xxti";
--- /dev/null
+/*
+ * Samsung's Exynos5250 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * Samsung's Exynos5250 SoC pin-mux and pin-config optiosn are listed as device
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/ {
+ pinctrl@11400000 {
+ gpa0: gpa0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpa1: gpa1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpa2: gpa2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb0: gpb0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb1: gpb1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb2: gpb2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb3: gpb3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc0: gpc0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc1: gpc1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc2: gpc2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc3: gpc3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd0: gpd0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd1: gpd1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpy0: gpy0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpy1: gpy1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpy2: gpy2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpy3: gpy3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpy4: gpy4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpy5: gpy5 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpy6: gpy6 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpc4: gpc4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpx0: gpx0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ interrupt-parent = <&combiner>;
+ #interrupt-cells = <2>;
+ interrupts = <23 0>, <24 0>, <25 0>, <25 1>,
+ <26 0>, <26 1>, <27 0>, <27 1>;
+ };
+
+ gpx1: gpx1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ interrupt-parent = <&combiner>;
+ #interrupt-cells = <2>;
+ interrupts = <28 0>, <28 1>, <29 0>, <29 1>,
+ <30 0>, <30 1>, <31 0>, <31 1>;
+ };
+
+ gpx2: gpx2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpx3: gpx3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ uart0_data: uart0-data {
+ samsung,pins = "gpa0-0", "gpa0-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart0_fctl: uart0-fctl {
+ samsung,pins = "gpa0-2", "gpa0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samaung,pin-drv = <0>;
+ };
+
+ i2c2_bus: i2c2-bus {
+ samsung,pins = "gpa0-6", "gpa0-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ i2c2_hs_bus: i2c2-hs-bus {
+ samsung,pins = "gpa0-6", "gpa0-7";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ uart2_data: uart2-data {
+ samsung,pins = "gpa1-0", "gpa1-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart2_fctl: uart2-fctl {
+ samsung,pins = "gpa1-2", "gpa1-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samaung,pin-drv = <0>;
+ };
+
+ i2c3_bus: i2c3-bus {
+ samsung,pins = "gpa1-2", "gpa1-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ i2c3_hs_bus: i2c3-hs-bus {
+ samsung,pins = "gpa1-2", "gpa1-3";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ uart3_data: uart3-data {
+ samsung,pins = "gpa1-4", "gpa1-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi0_bus: spi0-bus {
+ samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c4_bus: i2c4-bus {
+ samsung,pins = "gpa2-0", "gpa2-1";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ i2c5_bus: i2c5-bus {
+ samsung,pins = "gpa2-2", "gpa2-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ spi1_bus: spi1-bus {
+ samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2s1_bus: i2s1-bus {
+ samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+ "gpb0-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pcm1_bus: pcm1-bus {
+ samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+ "gpb0-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ ac97_bus: ac97-bus {
+ samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+ "gpb0-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2s2_bus: i2s2-bus {
+ samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
+ "gpb1-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pcm2_bus: pcm2-bus {
+ samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
+ "gpb1-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ spdif_bus: spdif-bus {
+ samsung,pins = "gpb1-0", "gpb1-1";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi2_bus: spi2-bus {
+ samsung,pins = "gpb1-1", "gpb1-3", "gpb1-4";
+ samsung,pin-function = <5>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c6_bus: i2c6-bus {
+ samsung,pins = "gpb1-3", "gpb1-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c7_bus: i2c7-bus {
+ samsung,pins = "gpb2-2", "gpb2-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c0_bus: i2c0-bus {
+ samsung,pins = "gpb3-0", "gpb3-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c1_bus: i2c1-bus {
+ samsung,pins = "gpb3-2", "gpb3-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2c0_hs_bus: i2c0-hs-bus {
+ samsung,pins = "gpb3-0", "gpb3-1";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ i2c1_hs_bus: i2c1-hs-bus {
+ samsung,pins = "gpb3-2", "gpb3-3";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ sd0_clk: sd0-clk {
+ samsung,pins = "gpc0-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_cmd: sd0-cmd {
+ samsung,pins = "gpc0-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_cd: sd0-cd {
+ samsung,pins = "gpc0-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus1: sd0-bus-width1 {
+ samsung,pins = "gpc0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus4: sd0-bus-width4 {
+ samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5", "gpc0-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus8: sd0-bus-width8 {
+ samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_clk: sd1-clk {
+ samsung,pins = "gpc2-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_cmd: sd1-cmd {
+ samsung,pins = "gpc2-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_cd: sd1-cd {
+ samsung,pins = "gpc2-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_bus1: sd1-bus-width1 {
+ samsung,pins = "gpc2-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_bus4: sd1-bus-width4 {
+ samsung,pins = "gpc2-3", "gpc2-4", "gpc2-5", "gpc2-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_clk: sd2-clk {
+ samsung,pins = "gpc3-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_cmd: sd2-cmd {
+ samsung,pins = "gpc3-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_cd: sd2-cd {
+ samsung,pins = "gpc3-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_bus1: sd2-bus-width1 {
+ samsung,pins = "gpc3-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_bus4: sd2-bus-width4 {
+ samsung,pins = "gpc3-3", "gpc3-4", "gpc3-5", "gpc3-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_bus8: sd2-bus-width8 {
+ samsung,pins = "gpc4-3", "gpc4-4", "gpc4-5", "gpc4-6";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd3_clk: sd3-clk {
+ samsung,pins = "gpc4-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd3_cmd: sd3-cmd {
+ samsung,pins = "gpc4-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd3_cd: sd3-cd {
+ samsung,pins = "gpc4-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd3_bus1: sd3-bus-width1 {
+ samsung,pins = "gpc4-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd3_bus4: sd3-bus-width4 {
+ samsung,pins = "gpc4-3", "gpc4-4", "gpc4-5", "gpc4-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ uart1_data: uart1-data {
+ samsung,pins = "gpd0-0", "gpd0-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart1_fctl: uart1-fctl {
+ samsung,pins = "gpd0-2", "gpd0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samaung,pin-drv = <0>;
+ };
+ };
+
+ pinctrl@13400000 {
+ gpe0: gpe0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpe1: gpe1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf0: gpf0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf1: gpf1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg0: gpg0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg1: gpg1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg2: gpg2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gph0: gph0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gph1: gph1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ cam_gpio_a: cam-gpio-a {
+ samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
+ "gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
+ "gpe1-0", "gpe1-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ cam_gpio_b: cam-gpio-b {
+ samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
+ "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samaung,pin-drv = <0>;
+ };
+
+ cam_i2c2_bus: cam-i2c2-bus {
+ samsung,pins = "gpe0-6", "gpe1-0";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ cam_spi1_bus: cam-spi1-bus {
+ samsung,pins = "gpe0-4", "gpe0-5", "gpf0-2", "gpf0-3";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <0>;
+ samaung,pin-drv = <0>;
+ };
+
+ cam_i2c1_bus: cam-i2c1-bus {
+ samsung,pins = "gpf0-2", "gpf0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ cam_i2c0_bus: cam-i2c0-bus {
+ samsung,pins = "gpf0-0", "gpf0-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samaung,pin-drv = <0>;
+ };
+
+ cam_spi0_bus: cam-spi0-bus {
+ samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samaung,pin-drv = <0>;
+ };
+
+ cam_bayrgb_bus: cam-bayrgb-bus {
+ samsung,pins = "gpg0-0", "gpg0-1", "gpg0-2", "gpg0-3",
+ "gpg0-4", "gpg0-5", "gpg0-6", "gpg0-7",
+ "gpg1-0", "gpg1-1", "gpg1-2", "gpg1-3",
+ "gpg1-4", "gpg1-5", "gpg1-6", "gpg1-7",
+ "gpg2-0", "gpg2-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samaung,pin-drv = <0>;
+ };
+
+ cam_port_a: cam-port-a {
+ samsung,pins = "gph0-0", "gph0-1", "gph0-2", "gph0-3",
+ "gph1-0", "gph1-1", "gph1-2", "gph1-3",
+ "gph1-4", "gph1-5", "gph1-6", "gph1-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samaung,pin-drv = <0>;
+ };
+ };
+
+ pinctrl@10d10000 {
+ gpv0: gpv0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpv1: gpv1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpv2: gpv2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpv3: gpv3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpv4: gpv4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ c2c_rxd: c2c-rxd {
+ samsung,pins = "gpv0-0", "gpv0-1", "gpv0-2", "gpv0-3",
+ "gpv0-4", "gpv0-5", "gpv0-6", "gpv0-7",
+ "gpv1-0", "gpv1-1", "gpv1-2", "gpv1-3",
+ "gpv1-4", "gpv1-5", "gpv1-6", "gpv1-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samaung,pin-drv = <0>;
+ };
+
+ c2c_txd: c2c-txd {
+ samsung,pins = "gpv2-0", "gpv2-1", "gpv2-2", "gpv2-3",
+ "gpv2-4", "gpv2-5", "gpv2-6", "gpv2-7",
+ "gpv3-0", "gpv3-1", "gpv3-2", "gpv3-3",
+ "gpv3-4", "gpv3-5", "gpv3-6", "gpv3-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samaung,pin-drv = <0>;
+ };
+ };
+
+ pinctrl@03680000 {
+ gpz: gpz {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ i2s0_bus: i2s0-bus {
+ samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
+ "gpz-4", "gpz-5", "gpz-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+ };
+};
i2c@12C60000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <20000>;
- gpios = <&gpb3 0 2 3 0>,
- <&gpb3 1 2 3 0>;
eeprom@50 {
compatible = "samsung,s524ad0xd1";
i2c@12C70000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <20000>;
- gpios = <&gpb3 2 2 3 0>,
- <&gpb3 3 2 3 0>;
eeprom@51 {
compatible = "samsung,s524ad0xd1";
i2c@12C80000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <66000>;
- gpios = <&gpa0 6 3 3 0>,
- <&gpa0 7 3 3 0>;
hdmiddc@50 {
compatible = "samsung,exynos5-hdmiddc";
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
slot@0 {
reg = <0>;
bus-width = <8>;
- gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
- <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
- <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
- <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
- <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
};
};
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
slot@0 {
reg = <0>;
bus-width = <4>;
- samsung,cd-pinmux-gpio = <&gpc3 2 2 3 3>;
disable-wp;
- gpios = <&gpc3 0 2 0 3>, <&gpc3 1 2 0 3>,
- <&gpc3 3 2 3 3>, <&gpc3 4 2 3 3>,
- <&gpc3 5 2 3 3>, <&gpc3 6 2 3 3>,
- <&gpc4 3 3 3 3>, <&gpc4 3 3 3 3>,
- <&gpc4 5 3 3 3>, <&gpc4 6 3 3 3>;
};
};
};
spi_1: spi@12d30000 {
- gpios = <&gpa2 4 2 3 0>,
- <&gpa2 6 2 3 0>,
- <&gpa2 7 2 3 0>;
-
w25q80bw@0 {
#address-cells = <1>;
#size-cells = <1>;
spi-max-frequency = <1000000>;
controller-data {
- cs-gpio = <&gpa2 5 1 0 3>;
+ cs-gpio = <&gpa2 5 0>;
samsung,spi-feedback-delay = <0>;
};
};
hdmi {
- hpd-gpio = <&gpx3 7 0xf 1 3>;
+ hpd-gpio = <&gpx3 7 0>;
};
codec@11000000 {
};
i2s0: i2s@03830000 {
- gpios = <&gpz 0 2 0 0>, <&gpz 1 2 0 0>, <&gpz 2 2 0 0>,
- <&gpz 3 2 0 0>, <&gpz 4 2 0 0>, <&gpz 5 2 0 0>,
- <&gpz 6 2 0 0>;
+ status = "okay";
};
i2s1: i2s@12D60000 {
samsung,lane-count = <4>;
};
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing@0 {
+ /* 1280x800 */
+ clock-frequency = <50000>;
+ hactive = <1280>;
+ vactive = <800>;
+ hfront-porch = <4>;
+ hback-porch = <4>;
+ hsync-len = <4>;
+ vback-porch = <4>;
+ vfront-porch = <4>;
+ vsync-len = <4>;
+ };
+ };
+
fixed-rate-clocks {
xxti {
compatible = "samsung,clock-xxti";
model = "Google Snow";
compatible = "google,snow", "samsung,exynos5250";
+ aliases {
+ i2c104 = &i2c_104;
+ };
+
+ pinctrl@11400000 {
+ sd3_clk: sd3-clk {
+ samsung,pin-drv = <0>;
+ };
+
+ sd3_cmd: sd3-cmd {
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ sd3_bus4: sd3-bus-width4 {
+ samsung,pin-drv = <0>;
+ };
+ };
+
gpio-keys {
compatible = "gpio-keys";
lid-switch {
label = "Lid";
- gpios = <&gpx3 5 0 0x10000 0>;
+ gpios = <&gpx3 5 1>;
linux,input-type = <5>; /* EV_SW */
linux,code = <0>; /* SW_LID */
debounce-interval = <1>;
};
};
+ i2c-arbitrator {
+ compatible = "i2c-arb-gpio-challenge";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c-parent = <&{/i2c@12CA0000}>;
+
+ our-claim-gpio = <&gpf0 3 1>;
+ their-claim-gpios = <&gpe0 4 1>;
+ slew-delay-us = <10>;
+ wait-retry-us = <3000>;
+ wait-free-us = <50000>;
+
+ /* Use ID 104 as a hint that we're on physical bus 4 */
+ i2c_104: i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ battery: sbs-battery@b {
+ compatible = "sbs,sbs-battery";
+ reg = <0xb>;
+ sbs,poll-retry-count = <1>;
+ };
+
+ ec: embedded-controller {
+ compatible = "google,cros-ec-i2c";
+ reg = <0x1e>;
+ interrupts = <6 0>;
+ interrupt-parent = <&gpx1>;
+ wakeup-source;
+
+ keyboard-controller {
+ compatible = "google,cros-ec-keyb";
+ keypad,num-rows = <8>;
+ keypad,num-columns = <13>;
+ google,needs-ghost-filter;
+ linux,keymap = <0x0001003a /* CAPSLK */
+ 0x0002003b /* F1 */
+ 0x00030030 /* B */
+ 0x00040044 /* F10 */
+ 0x00060031 /* N */
+ 0x0008000d /* = */
+ 0x000a0064 /* R_ALT */
+
+ 0x01010001 /* ESC */
+ 0x0102003e /* F4 */
+ 0x01030022 /* G */
+ 0x01040041 /* F7 */
+ 0x01060023 /* H */
+ 0x01080028 /* ' */
+ 0x01090043 /* F9 */
+ 0x010b000e /* BKSPACE */
+
+ 0x0200001d /* L_CTRL */
+ 0x0201000f /* TAB */
+ 0x0202003d /* F3 */
+ 0x02030014 /* T */
+ 0x02040040 /* F6 */
+ 0x0205001b /* ] */
+ 0x02060015 /* Y */
+ 0x02070056 /* 102ND */
+ 0x0208001a /* [ */
+ 0x02090042 /* F8 */
+
+ 0x03010029 /* GRAVE */
+ 0x0302003c /* F2 */
+ 0x03030006 /* 5 */
+ 0x0304003f /* F5 */
+ 0x03060007 /* 6 */
+ 0x0308000c /* - */
+ 0x030b002b /* \ */
+
+ 0x04000061 /* R_CTRL */
+ 0x0401001e /* A */
+ 0x04020020 /* D */
+ 0x04030021 /* F */
+ 0x0404001f /* S */
+ 0x04050025 /* K */
+ 0x04060024 /* J */
+ 0x04080027 /* ; */
+ 0x04090026 /* L */
+ 0x040b001c /* ENTER */
+
+ 0x0501002c /* Z */
+ 0x0502002e /* C */
+ 0x0503002f /* V */
+ 0x0504002d /* X */
+ 0x05050033 /* , */
+ 0x05060032 /* M */
+ 0x0507002a /* L_SHIFT */
+ 0x05080035 /* / */
+ 0x05090034 /* . */
+ 0x050B0039 /* SPACE */
+
+ 0x06010002 /* 1 */
+ 0x06020004 /* 3 */
+ 0x06030005 /* 4 */
+ 0x06040003 /* 2 */
+ 0x06050009 /* 8 */
+ 0x06060008 /* 7 */
+ 0x0608000b /* 0 */
+ 0x0609000a /* 9 */
+ 0x060a0038 /* L_ALT */
+ 0x060b006c /* DOWN */
+ 0x060c006a /* RIGHT */
+
+ 0x07010010 /* Q */
+ 0x07020012 /* E */
+ 0x07030013 /* R */
+ 0x07040011 /* W */
+ 0x07050017 /* I */
+ 0x07060016 /* U */
+ 0x07070036 /* R_SHIFT */
+ 0x07080019 /* P */
+ 0x07090018 /* O */
+ 0x070b0067 /* UP */
+ 0x070c0069>; /* LEFT */
+ };
+ };
+ };
+ };
+
/*
* On Snow we've got SIP WiFi and so can keep drive strengths low to
* reduce EMI.
*/
dwmmc3@12230000 {
slot@0 {
- gpios = <&gpc4 0 2 0 0>, <&gpc4 1 2 3 0>,
- <&gpc4 3 2 3 0>, <&gpc4 4 2 3 0>,
- <&gpc4 5 2 3 0>, <&gpc4 6 2 3 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
};
};
*/
/include/ "skeleton.dtsi"
+/include/ "exynos5250-pinctrl.dtsi"
/ {
compatible = "samsung,exynos5250";
i2c6 = &i2c_6;
i2c7 = &i2c_7;
i2c8 = &i2c_8;
+ pinctrl0 = &pinctrl_0;
+ pinctrl1 = &pinctrl_1;
+ pinctrl2 = &pinctrl_2;
+ pinctrl3 = &pinctrl_3;
+ };
+
+ chipid@10000000 {
+ compatible = "samsung,exynos4210-chipid";
+ reg = <0x10000000 0x100>;
};
pd_gsc: gsc-power-domain@0x10044000 {
};
gic:interrupt-controller@10481000 {
- compatible = "arm,cortex-a9-gic";
+ compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
#interrupt-cells = <3>;
interrupt-controller;
- reg = <0x10481000 0x1000>, <0x10482000 0x2000>;
+ reg = <0x10481000 0x1000>,
+ <0x10482000 0x1000>,
+ <0x10484000 0x2000>,
+ <0x10486000 0x2000>;
+ interrupts = <1 9 0xf04>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <1 13 0xf08>,
+ <1 14 0xf08>,
+ <1 11 0xf08>,
+ <1 10 0xf08>;
};
combiner:interrupt-controller@10440000 {
interrupts = <1 2>, <22 4>;
};
+ pinctrl_0: pinctrl@11400000 {
+ compatible = "samsung,exynos5250-pinctrl";
+ reg = <0x11400000 0x1000>;
+ interrupts = <0 46 0>;
+
+ wakup_eint: wakeup-interrupt-controller {
+ compatible = "samsung,exynos4210-wakeup-eint";
+ interrupt-parent = <&gic>;
+ interrupts = <0 32 0>;
+ };
+ };
+
+ pinctrl_1: pinctrl@13400000 {
+ compatible = "samsung,exynos5250-pinctrl";
+ reg = <0x13400000 0x1000>;
+ interrupts = <0 45 0>;
+ };
+
+ pinctrl_2: pinctrl@10d10000 {
+ compatible = "samsung,exynos5250-pinctrl";
+ reg = <0x10d10000 0x1000>;
+ interrupts = <0 50 0>;
+ };
+
+ pinctrl_3: pinctrl@03680000 {
+ compatible = "samsung,exynos5250-pinctrl";
+ reg = <0x0368000 0x1000>;
+ interrupts = <0 47 0>;
+ };
+
watchdog {
compatible = "samsung,s3c2410-wdt";
reg = <0x101D0000 0x100>;
#size-cells = <0>;
clocks = <&clock 294>;
clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
};
i2c_1: i2c@12C70000 {
#size-cells = <0>;
clocks = <&clock 295>;
clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
};
i2c_2: i2c@12C80000 {
#size-cells = <0>;
clocks = <&clock 296>;
clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
};
i2c_3: i2c@12C90000 {
#size-cells = <0>;
clocks = <&clock 297>;
clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_bus>;
};
i2c_4: i2c@12CA0000 {
#size-cells = <0>;
clocks = <&clock 298>;
clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_bus>;
};
i2c_5: i2c@12CB0000 {
#size-cells = <0>;
clocks = <&clock 299>;
clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_bus>;
};
i2c_6: i2c@12CC0000 {
#size-cells = <0>;
clocks = <&clock 300>;
clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_bus>;
};
i2c_7: i2c@12CD0000 {
#size-cells = <0>;
clocks = <&clock 301>;
clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_bus>;
};
i2c_8: i2c@12CE0000 {
#size-cells = <0>;
clocks = <&clock 304>, <&clock 154>;
clock-names = "spi", "spi_busclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_bus>;
};
spi_1: spi@12d30000 {
#size-cells = <0>;
clocks = <&clock 305>, <&clock 155>;
clock-names = "spi", "spi_busclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_bus>;
};
spi_2: spi@12d40000 {
#size-cells = <0>;
clocks = <&clock 306>, <&clock 156>;
clock-names = "spi", "spi_busclk0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_bus>;
};
dwmmc_0: dwmmc0@12200000 {
samsung,supports-rstclr;
samsung,supports-secdai;
samsung,idma-addr = <0x03000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_bus>;
};
i2s1: i2s@12D60000 {
dmas = <&pdma1 12
&pdma1 11>;
dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1_bus>;
};
i2s2: i2s@12D70000 {
dmas = <&pdma0 12
&pdma0 11>;
dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s2_bus>;
};
usb@12110000 {
compatible = "samsung,exynos4210-ehci";
reg = <0x12110000 0x100>;
interrupts = <0 71 0>;
+
+ clocks = <&clock 285>;
+ clock-names = "usbhost";
};
usb@12120000 {
compatible = "samsung,exynos4210-ohci";
reg = <0x12120000 0x100>;
interrupts = <0 71 0>;
+
+ clocks = <&clock 285>;
+ clock-names = "usbhost";
};
amba {
};
};
- gpio-controllers {
- #address-cells = <1>;
- #size-cells = <1>;
- gpio-controller;
- ranges;
-
- gpa0: gpio-controller@11400000 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400000 0x20>;
- #gpio-cells = <4>;
- };
-
- gpa1: gpio-controller@11400020 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400020 0x20>;
- #gpio-cells = <4>;
- };
-
- gpa2: gpio-controller@11400040 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400040 0x20>;
- #gpio-cells = <4>;
- };
-
- gpb0: gpio-controller@11400060 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400060 0x20>;
- #gpio-cells = <4>;
- };
-
- gpb1: gpio-controller@11400080 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400080 0x20>;
- #gpio-cells = <4>;
- };
-
- gpb2: gpio-controller@114000A0 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x114000A0 0x20>;
- #gpio-cells = <4>;
- };
-
- gpb3: gpio-controller@114000C0 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x114000C0 0x20>;
- #gpio-cells = <4>;
- };
-
- gpc0: gpio-controller@114000E0 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x114000E0 0x20>;
- #gpio-cells = <4>;
- };
-
- gpc1: gpio-controller@11400100 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400100 0x20>;
- #gpio-cells = <4>;
- };
-
- gpc2: gpio-controller@11400120 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400120 0x20>;
- #gpio-cells = <4>;
- };
-
- gpc3: gpio-controller@11400140 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400140 0x20>;
- #gpio-cells = <4>;
- };
-
- gpc4: gpio-controller@114002E0 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x114002E0 0x20>;
- #gpio-cells = <4>;
- };
-
- gpd0: gpio-controller@11400160 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400160 0x20>;
- #gpio-cells = <4>;
- };
-
- gpd1: gpio-controller@11400180 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400180 0x20>;
- #gpio-cells = <4>;
- };
-
- gpy0: gpio-controller@114001A0 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x114001A0 0x20>;
- #gpio-cells = <4>;
- };
-
- gpy1: gpio-controller@114001C0 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x114001C0 0x20>;
- #gpio-cells = <4>;
- };
-
- gpy2: gpio-controller@114001E0 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x114001E0 0x20>;
- #gpio-cells = <4>;
- };
-
- gpy3: gpio-controller@11400200 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400200 0x20>;
- #gpio-cells = <4>;
- };
-
- gpy4: gpio-controller@11400220 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400220 0x20>;
- #gpio-cells = <4>;
- };
-
- gpy5: gpio-controller@11400240 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400240 0x20>;
- #gpio-cells = <4>;
- };
-
- gpy6: gpio-controller@11400260 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400260 0x20>;
- #gpio-cells = <4>;
- };
-
- gpx0: gpio-controller@11400C00 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400C00 0x20>;
- #gpio-cells = <4>;
- };
-
- gpx1: gpio-controller@11400C20 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400C20 0x20>;
- #gpio-cells = <4>;
- };
-
- gpx2: gpio-controller@11400C40 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400C40 0x20>;
- #gpio-cells = <4>;
- };
-
- gpx3: gpio-controller@11400C60 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x11400C60 0x20>;
- #gpio-cells = <4>;
- };
-
- gpe0: gpio-controller@13400000 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x13400000 0x20>;
- #gpio-cells = <4>;
- };
-
- gpe1: gpio-controller@13400020 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x13400020 0x20>;
- #gpio-cells = <4>;
- };
-
- gpf0: gpio-controller@13400040 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x13400040 0x20>;
- #gpio-cells = <4>;
- };
-
- gpf1: gpio-controller@13400060 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x13400060 0x20>;
- #gpio-cells = <4>;
- };
-
- gpg0: gpio-controller@13400080 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x13400080 0x20>;
- #gpio-cells = <4>;
- };
-
- gpg1: gpio-controller@134000A0 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x134000A0 0x20>;
- #gpio-cells = <4>;
- };
-
- gpg2: gpio-controller@134000C0 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x134000C0 0x20>;
- #gpio-cells = <4>;
- };
-
- gph0: gpio-controller@134000E0 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x134000E0 0x20>;
- #gpio-cells = <4>;
- };
-
- gph1: gpio-controller@13400100 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x13400100 0x20>;
- #gpio-cells = <4>;
- };
-
- gpv0: gpio-controller@10D10000 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x10D10000 0x20>;
- #gpio-cells = <4>;
- };
-
- gpv1: gpio-controller@10D10020 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x10D10020 0x20>;
- #gpio-cells = <4>;
- };
-
- gpv2: gpio-controller@10D10040 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x10D10060 0x20>;
- #gpio-cells = <4>;
- };
-
- gpv3: gpio-controller@10D10060 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x10D10080 0x20>;
- #gpio-cells = <4>;
- };
-
- gpv4: gpio-controller@10D10080 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x10D100C0 0x20>;
- #gpio-cells = <4>;
- };
-
- gpz: gpio-controller@03860000 {
- compatible = "samsung,exynos4-gpio";
- reg = <0x03860000 0x20>;
- #gpio-cells = <4>;
- };
- };
-
-
gsc_0: gsc@0x13e00000 {
compatible = "samsung,exynos5-gsc";
reg = <0x13e00000 0x1000>;
samsung,enable-mask = <1>;
};
};
+
+ fimd {
+ compatible = "samsung,exynos5250-fimd";
+ interrupt-parent = <&combiner>;
+ reg = <0x14400000 0x40000>;
+ interrupt-names = "fifo", "vsync", "lcd_sys";
+ interrupts = <18 4>, <18 5>, <18 6>;
+ clocks = <&clock 133>, <&clock 339>;
+ clock-names = "sclk_fimd", "fimd";
+ };
};
--- /dev/null
+/*
+ * SAMSUNG SD5v1 board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ "exynos5440.dtsi"
+
+/ {
+ model = "SAMSUNG SD5v1 board based on EXYNOS5440";
+ compatible = "samsung,sd5v1", "samsung,exynos5440";
+
+ chosen {
+ bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 console=ttySAC0,115200";
+ };
+
+ fixed-rate-clocks {
+ xtal {
+ compatible = "samsung,clock-xtal";
+ clock-frequency = <50000000>;
+ };
+ };
+
+ gmac: ethernet@00230000 {
+ fixed_phy;
+ phy_addr = <1>;
+ };
+
+ spi {
+ status = "disabled";
+ };
+
+};
model = "SAMSUNG SSDK5440 board based on EXYNOS5440";
compatible = "samsung,ssdk5440", "samsung,exynos5440";
- memory {
- reg = <0x80000000 0x80000000>;
- };
-
chosen {
- bootargs = "root=/dev/ram0 rw ramdisk=8192 initrd=0x81000000,8M console=ttySAC0,115200 init=/linuxrc";
+ bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 console=ttySAC0,115200";
};
spi {
compatible = "arm,cortex-a15-gic";
#interrupt-cells = <3>;
interrupt-controller;
- reg = <0x2E1000 0x1000>, <0x2E2000 0x1000>;
+ reg = <0x2E1000 0x1000>,
+ <0x2E2000 0x1000>,
+ <0x2E4000 0x2000>,
+ <0x2E6000 0x2000>;
+ interrupts = <1 9 0xf04>;
};
cpus {
};
};
+ arm-pmu {
+ compatible = "arm,cortex-a15-pmu", "arm,cortex-a9-pmu";
+ interrupts = <0 52 4>,
+ <0 53 4>,
+ <0 54 4>,
+ <0 55 4>;
+ };
+
timer {
compatible = "arm,cortex-a15-timer",
"arm,armv7-timer";
clock-frequency = <50000000>;
};
+ cpufreq@160000 {
+ compatible = "samsung,exynos5440-cpufreq";
+ reg = <0x160000 0x1000>;
+ interrupts = <0 57 0>;
+ operating-points = <
+ /* KHz uV */
+ 1200000 1025000
+ 1000000 975000
+ 800000 925000
+ >;
+ };
+
serial@B0000 {
compatible = "samsung,exynos4210-uart";
reg = <0xB0000 0x1000>;
pinctrl {
compatible = "samsung,exynos5440-pinctrl";
reg = <0xE0000 0x1000>;
+ interrupts = <0 37 0>, <0 38 0>, <0 39 0>, <0 40 0>,
+ <0 41 0>, <0 42 0>, <0 43 0>, <0 44 0>;
interrupt-controller;
#interrupt-cells = <2>;
#gpio-cells = <2>;
clock-names = "watchdog";
};
+ gmac: ethernet@00230000 {
+ compatible = "snps,dwmac-3.70a";
+ reg = <0x00230000 0x8000>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 31 4>;
+ interrupt-names = "macirq";
+ phy-mode = "sgmii";
+ clocks = <&clock 25>;
+ clock-names = "stmmaceth";
+ };
+
amba {
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&gic>;
ranges;
- pdma0: pdma@121A0000 {
+ pdma0: pdma@00121000 {
compatible = "arm,pl330", "arm,primecell";
- reg = <0x120000 0x1000>;
- interrupts = <0 34 0>;
- clocks = <&clock 21>;
+ reg = <0x121000 0x1000>;
+ interrupts = <0 46 0>;
+ clocks = <&clock 8>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
#dma-requests = <32>;
};
- pdma1: pdma@121B0000 {
+ pdma1: pdma@00120000 {
compatible = "arm,pl330", "arm,primecell";
- reg = <0x121000 0x1000>;
- interrupts = <0 35 0>;
- clocks = <&clock 21>;
+ reg = <0x120000 0x1000>;
+ interrupts = <0 47 0>;
+ clocks = <&clock 8>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a>;
- panel-enable-gpios = <&gpio1 18 0>;
+ lcd-supply = <®_lcd_3v3>;
+ display = <&display>;
status = "okay";
+
+ display: display {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9200000>;
+ hactive = <480>;
+ vactive = <272>;
+ hback-porch = <15>;
+ hfront-porch = <8>;
+ vback-porch = <12>;
+ vfront-porch = <4>;
+ hsync-len = <1>;
+ vsync-len = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
};
};
regulator-max-microvolt = <3300000>;
gpio = <&gpio1 29 0>;
};
+
+ reg_lcd_3v3: lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 18 0>;
+ enable-active-high;
+ };
};
backlight {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>;
bus-width = <4>;
+ broken-cd;
status = "okay";
};
reg = <0x80000000 0x2000>;
};
- dma-apbh@80004000 {
+ dma_apbh: dma-apbh@80004000 {
compatible = "fsl,imx23-dma-apbh";
reg = <0x80004000 0x2000>;
+ interrupts = <0 14 20 0
+ 13 13 13 13>;
+ interrupt-names = "empty", "ssp0", "ssp1", "empty",
+ "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+ #dma-cells = <1>;
+ dma-channels = <8>;
clocks = <&clks 15>;
};
interrupt-names = "gpmi-dma", "bch";
clocks = <&clks 34>;
clock-names = "gpmi_io";
+ dmas = <&dma_apbh 4>;
+ dma-names = "rx-tx";
fsl,gpmi-dma-channel = <4>;
status = "disabled";
};
reg = <0x80010000 0x2000>;
interrupts = <15 14>;
clocks = <&clks 33>;
+ dmas = <&dma_apbh 1>;
+ dma-names = "rx-tx";
fsl,ssp-dma-channel = <1>;
status = "disabled";
};
status = "disabled";
};
- dma-apbx@80024000 {
+ dma_apbx: dma-apbx@80024000 {
compatible = "fsl,imx23-dma-apbx";
reg = <0x80024000 0x2000>;
+ interrupts = <7 5 9 26
+ 19 0 25 23
+ 60 58 9 0
+ 0 0 0 0>;
+ interrupt-names = "audio-adc", "audio-dac", "spdif-tx", "i2c",
+ "saif0", "empty", "auart0-rx", "auart0-tx",
+ "auart1-rx", "auart1-tx", "saif1", "empty",
+ "empty", "empty", "empty", "empty";
+ #dma-cells = <1>;
+ dma-channels = <16>;
clocks = <&clks 16>;
};
reg = <0x80034000 0x2000>;
interrupts = <2 20>;
clocks = <&clks 33>;
+ dmas = <&dma_apbh 2>;
+ dma-names = "rx-tx";
fsl,ssp-dma-channel = <2>;
status = "disabled";
};
saif0: saif@80042000 {
reg = <0x80042000 0x2000>;
+ dmas = <&dma_apbx 4>;
+ dma-names = "rx-tx";
status = "disabled";
};
saif1: saif@80046000 {
reg = <0x80046000 0x2000>;
+ dmas = <&dma_apbx 10>;
+ dma-names = "rx-tx";
status = "disabled";
};
audio-out@80048000 {
reg = <0x80048000 0x2000>;
+ dmas = <&dma_apbx 1>;
+ dma-names = "tx";
status = "disabled";
};
audio-in@8004c000 {
reg = <0x8004c000 0x2000>;
+ dmas = <&dma_apbx 0>;
+ dma-names = "rx";
status = "disabled";
};
spdif@80054000 {
reg = <0x80054000 2000>;
+ dmas = <&dma_apbx 2>;
+ dma-names = "tx";
status = "disabled";
};
i2c@80058000 {
reg = <0x80058000 0x2000>;
+ dmas = <&dma_apbx 3>;
+ dma-names = "rx-tx";
status = "disabled";
};
reg = <0x8006c000 0x2000>;
interrupts = <24 25 23>;
clocks = <&clks 32>;
+ dmas = <&dma_apbx 6>, <&dma_apbx 7>;
+ dma-names = "rx", "tx";
status = "disabled";
};
reg = <0x8006e000 0x2000>;
interrupts = <59 60 58>;
clocks = <&clks 32>;
+ dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+ dma-names = "rx", "tx";
status = "disabled";
};
pinctrl-names = "default";
pinctrl-0 = <&lcdif_16bit_pins_a
&lcdif_pins_apf28dev>;
+ display = <&display>;
status = "okay";
+
+ display: display {
+ bits-per-pixel = <16>;
+ bus-width = <16>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33000033>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <96>;
+ hfront-porch = <96>;
+ vback-porch = <20>;
+ vfront-porch = <21>;
+ hsync-len = <64>;
+ vsync-len = <4>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
};
};
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_apx4>;
+ display = <&display>;
status = "okay";
+
+ display: display {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <30000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <88>;
+ hfront-porch = <40>;
+ vback-porch = <32>;
+ vfront-porch = <13>;
+ hsync-len = <48>;
+ vsync-len = <3>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
};
};
reg = <0>;
fsl,pinmux-ids = <
0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
- 0x1153 /* MX28_PAD_LCD_D22__GPIO_1_21 */
0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */
0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
fsl,voltage = <1>;
fsl,pull-up = <0>;
};
+
+ w1_gpio_pins: w1-gpio@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */
+ >;
+ fsl,drive-strength = <1>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>; /* 0 will enable the keeper */
+ };
};
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_18bit_pins_cfa10049
&lcdif_pins_cfa10049>;
+ display = <&display>;
status = "okay";
+
+ display: display {
+ bits-per-pixel = <32>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9216000>;
+ hactive = <320>;
+ vactive = <480>;
+ hback-porch = <2>;
+ hfront-porch = <2>;
+ vback-porch = <2>;
+ vfront-porch = <2>;
+ hsync-len = <15>;
+ vsync-len = <15>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
};
};
usbphy1: usbphy@8007e000 {
status = "okay";
};
+
+ lradc@80050000 {
+ status = "okay";
+ fsl,lradc-touchscreen-wires = <4>;
+ };
};
};
pwms = <&pwm 3 5000000>;
brightness-levels = <0 4 8 16 32 64 128 255>;
default-brightness-level = <6>;
+
+ };
+
+ onewire@0 {
+ compatible = "w1-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&w1_gpio_pins>;
+ status = "okay";
+ gpios = <&gpio1 21 0>;
};
};
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_evk>;
- panel-enable-gpios = <&gpio3 30 0>;
+ lcd-supply = <®_lcd_3v3>;
+ display = <&display>;
status = "okay";
+
+ display: display {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33500000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <89>;
+ hfront-porch = <164>;
+ vback-porch = <23>;
+ vfront-porch = <10>;
+ hsync-len = <10>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
};
can0: can@80032000 {
gpio = <&gpio3 8 0>;
enable-active-high;
};
+
+ reg_lcd_3v3: lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 30 0>;
+ enable-active-high;
+ };
};
sound {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_m28>;
+ display = <&display>;
status = "okay";
+
+ display: display {
+ bits-per-pixel = <16>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33260000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <0>;
+ hfront-porch = <256>;
+ vback-porch = <0>;
+ vfront-porch = <45>;
+ hsync-len = <1>;
+ vsync-len = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
};
can0: can@80032000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>;
+ clocks = <&clks 57>, <&clks 57>;
+ clock-names = "ipg", "ahb";
status = "okay";
};
hsadc@80002000 {
reg = <0x80002000 0x2000>;
interrupts = <13 87>;
+ dmas = <&dma_apbh 12>;
+ dma-names = "rx";
status = "disabled";
};
- dma-apbh@80004000 {
+ dma_apbh: dma-apbh@80004000 {
compatible = "fsl,imx28-dma-apbh";
reg = <0x80004000 0x2000>;
+ interrupts = <82 83 84 85
+ 88 88 88 88
+ 88 88 88 88
+ 87 86 0 0>;
+ interrupt-names = "ssp0", "ssp1", "ssp2", "ssp3",
+ "gpmi0", "gmpi1", "gpmi2", "gmpi3",
+ "gpmi4", "gmpi5", "gpmi6", "gmpi7",
+ "hsadc", "lcdif", "empty", "empty";
+ #dma-cells = <1>;
+ dma-channels = <16>;
clocks = <&clks 25>;
};
interrupt-names = "gpmi-dma", "bch";
clocks = <&clks 50>;
clock-names = "gpmi_io";
+ dmas = <&dma_apbh 4>;
+ dma-names = "rx-tx";
fsl,gpmi-dma-channel = <4>;
status = "disabled";
};
reg = <0x80010000 0x2000>;
interrupts = <96 82>;
clocks = <&clks 46>;
+ dmas = <&dma_apbh 0>;
+ dma-names = "rx-tx";
fsl,ssp-dma-channel = <0>;
status = "disabled";
};
reg = <0x80012000 0x2000>;
interrupts = <97 83>;
clocks = <&clks 47>;
+ dmas = <&dma_apbh 1>;
+ dma-names = "rx-tx";
fsl,ssp-dma-channel = <1>;
status = "disabled";
};
reg = <0x80014000 0x2000>;
interrupts = <98 84>;
clocks = <&clks 48>;
+ dmas = <&dma_apbh 2>;
+ dma-names = "rx-tx";
fsl,ssp-dma-channel = <2>;
status = "disabled";
};
reg = <0x80016000 0x2000>;
interrupts = <99 85>;
clocks = <&clks 49>;
+ dmas = <&dma_apbh 3>;
+ dma-names = "rx-tx";
fsl,ssp-dma-channel = <3>;
status = "disabled";
};
status = "disabled";
};
- dma-apbx@80024000 {
+ dma_apbx: dma-apbx@80024000 {
compatible = "fsl,imx28-dma-apbx";
reg = <0x80024000 0x2000>;
+ interrupts = <78 79 66 0
+ 80 81 68 69
+ 70 71 72 73
+ 74 75 76 77>;
+ interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+ "saif0", "saif1", "i2c0", "i2c1",
+ "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
+ "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
+ #dma-cells = <1>;
+ dma-channels = <16>;
clocks = <&clks 26>;
};
reg = <0x80030000 0x2000>;
interrupts = <38 86>;
clocks = <&clks 55>;
+ dmas = <&dma_apbh 13>;
+ dma-names = "rx";
status = "disabled";
};
reg = <0x80042000 0x2000>;
interrupts = <59 80>;
clocks = <&clks 53>;
+ dmas = <&dma_apbx 4>;
+ dma-names = "rx-tx";
fsl,saif-dma-channel = <4>;
status = "disabled";
};
reg = <0x80046000 0x2000>;
interrupts = <58 81>;
clocks = <&clks 54>;
+ dmas = <&dma_apbx 5>;
+ dma-names = "rx-tx";
fsl,saif-dma-channel = <5>;
status = "disabled";
};
spdif@80054000 {
reg = <0x80054000 0x2000>;
interrupts = <45 66>;
+ dmas = <&dma_apbx 2>;
+ dma-names = "tx";
status = "disabled";
};
reg = <0x80058000 0x2000>;
interrupts = <111 68>;
clock-frequency = <100000>;
+ dmas = <&dma_apbx 6>;
+ dma-names = "rx-tx";
fsl,i2c-dma-channel = <6>;
status = "disabled";
};
reg = <0x8005a000 0x2000>;
interrupts = <110 69>;
clock-frequency = <100000>;
+ dmas = <&dma_apbx 7>;
+ dma-names = "rx-tx";
fsl,i2c-dma-channel = <7>;
status = "disabled";
};
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006a000 0x2000>;
interrupts = <112 70 71>;
+ dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+ dma-names = "rx", "tx";
fsl,auart-dma-channel = <8 9>;
clocks = <&clks 45>;
status = "disabled";
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006c000 0x2000>;
interrupts = <113 72 73>;
+ dmas = <&dma_apbx 10>, <&dma_apbx 11>;
+ dma-names = "rx", "tx";
clocks = <&clks 45>;
status = "disabled";
};
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006e000 0x2000>;
interrupts = <114 74 75>;
+ dmas = <&dma_apbx 12>, <&dma_apbx 13>;
+ dma-names = "rx", "tx";
clocks = <&clks 45>;
status = "disabled";
};
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x80070000 0x2000>;
interrupts = <115 76 77>;
+ dmas = <&dma_apbx 14>, <&dma_apbx 15>;
+ dma-names = "rx", "tx";
clocks = <&clks 45>;
status = "disabled";
};
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x80072000 0x2000>;
interrupts = <116 78 79>;
+ dmas = <&dma_apbx 0>, <&dma_apbx 1>;
+ dma-names = "rx", "tx";
clocks = <&clks 45>;
status = "disabled";
};
compatible = "fsl,imx28-fec";
reg = <0x800f0000 0x4000>;
interrupts = <101>;
- clocks = <&clks 57>, <&clks 57>;
- clock-names = "ipg", "ahb";
+ clocks = <&clks 57>, <&clks 57>, <&clks 64>;
+ clock-names = "ipg", "ahb", "enet_out";
status = "disabled";
};
interrupt-parent = <&intc>;
ranges;
- dma-apbh@00110000 {
+ dma_apbh: dma-apbh@00110000 {
compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
reg = <0x00110000 0x2000>;
+ interrupts = <0 13 0x04>, <0 13 0x04>, <0 13 0x04>, <0 13 0x04>;
+ interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+ #dma-cells = <1>;
+ dma-channels = <4>;
clocks = <&clks 106>;
};
<&clks 150>, <&clks 149>;
clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch",
"gpmi_bch_apb", "per1_bch";
+ dmas = <&dma_apbh 0>;
+ dma-names = "rx-tx";
fsl,gpmi-dma-channel = <0>;
status = "disabled";
};
};
};
+ pmu {
+ compatible = "arm,arm1136-pmu";
+ interrupts = <3>;
+ };
+
soc {
compatible = "ti,omap-infra";
mpu {
reg = <0x480FE000 0x1000>;
};
+ sdma: dma-controller@48056000 {
+ compatible = "ti,omap2430-sdma", "ti,omap2420-sdma";
+ reg = <0x48056000 0x1000>;
+ interrupts = <12>,
+ <13>,
+ <14>,
+ <15>;
+ #dma-cells = <1>;
+ #dma-channels = <32>;
+ #dma-requests = <64>;
+ };
+
uart1: serial@4806a000 {
compatible = "ti,omap2-uart";
ti,hwmods = "uart1";
};
timer2: timer@4802a000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x4802a000 0x400>;
interrupts = <38>;
ti,hwmods = "timer2";
};
timer3: timer@48078000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x48078000 0x400>;
interrupts = <39>;
ti,hwmods = "timer3";
};
timer4: timer@4807a000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x4807a000 0x400>;
interrupts = <40>;
ti,hwmods = "timer4";
};
timer5: timer@4807c000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x4807c000 0x400>;
interrupts = <41>;
ti,hwmods = "timer5";
};
timer6: timer@4807e000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x4807e000 0x400>;
interrupts = <42>;
ti,hwmods = "timer6";
};
timer7: timer@48080000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x48080000 0x400>;
interrupts = <43>;
ti,hwmods = "timer7";
};
timer8: timer@48082000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x48082000 0x400>;
interrupts = <44>;
ti,hwmods = "timer8";
};
timer9: timer@48084000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x48084000 0x400>;
interrupts = <45>;
ti,hwmods = "timer9";
};
timer10: timer@48086000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x48086000 0x400>;
interrupts = <46>;
ti,hwmods = "timer10";
};
timer11: timer@48088000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x48088000 0x400>;
interrupts = <47>;
ti,hwmods = "timer11";
};
timer12: timer@4808a000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x4808a000 0x400>;
interrupts = <48>;
ti,hwmods = "timer12";
reg = <0x80000000 0x4000000>; /* 64 MB */
};
};
+
+&gpmc {
+ ranges = <0 0 0x08000000 0x04000000>;
+
+ nor@0,0 {
+ compatible = "cfi-flash";
+ linux,mtd-name= "intel,ge28f256l18b85";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0 0 0x04000000>;
+ bank-width = <2>;
+
+ gpmc,mux-add-data = <2>;
+ gpmc,cs-on-ns = <10>;
+ gpmc,cs-rd-off-ns = <160>;
+ gpmc,cs-wr-off-ns = <160>;
+ gpmc,adv-on-ns = <20>;
+ gpmc,adv-rd-off-ns = <50>;
+ gpmc,adv-wr-off-ns = <50>;
+ gpmc,oe-on-ns = <60>;
+ gpmc,oe-off-ns = <120>;
+ gpmc,we-on-ns = <60>;
+ gpmc,we-off-ns = <120>;
+ gpmc,rd-cycle-ns = <170>;
+ gpmc,wr-cycle-ns = <170>;
+ gpmc,access-ns = <150>;
+ gpmc,page-burst-access-ns = <10>;
+
+ partition@0 {
+ label = "bootloader";
+ reg = <0 0x20000>;
+ };
+ partition@0x20000 {
+ label = "params";
+ reg = <0x20000 0x20000>;
+ };
+ partition@0x40000 {
+ label = "kernel";
+ reg = <0x40000 0x200000>;
+ };
+ partition@0x240000 {
+ label = "file-system";
+ reg = <0x240000 0x3dc0000>;
+ };
+ };
+};
pinctrl-single,function-mask = <0x3f>;
};
+ gpio1: gpio@48018000 {
+ compatible = "ti,omap2-gpio";
+ reg = <0x48018000 0x200>;
+ interrupts = <29>;
+ ti,hwmods = "gpio1";
+ ti,gpio-always-on;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ gpio2: gpio@4801a000 {
+ compatible = "ti,omap2-gpio";
+ reg = <0x4801a000 0x200>;
+ interrupts = <30>;
+ ti,hwmods = "gpio2";
+ ti,gpio-always-on;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ gpio3: gpio@4801c000 {
+ compatible = "ti,omap2-gpio";
+ reg = <0x4801c000 0x200>;
+ interrupts = <31>;
+ ti,hwmods = "gpio3";
+ ti,gpio-always-on;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ gpio4: gpio@4801e000 {
+ compatible = "ti,omap2-gpio";
+ reg = <0x4801e000 0x200>;
+ interrupts = <32>;
+ ti,hwmods = "gpio4";
+ ti,gpio-always-on;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ gpmc: gpmc@6800a000 {
+ compatible = "ti,omap2420-gpmc";
+ reg = <0x6800a000 0x1000>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ interrupts = <20>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <4>;
+ ti,hwmods = "gpmc";
+ };
+
mcbsp1: mcbsp@48074000 {
compatible = "ti,omap2420-mcbsp";
reg = <0x48074000 0xff>;
<60>; /* RX interrupt */
interrupt-names = "tx", "rx";
ti,hwmods = "mcbsp1";
+ dmas = <&sdma 31>,
+ <&sdma 32>;
+ dma-names = "tx", "rx";
};
mcbsp2: mcbsp@48076000 {
<63>; /* RX interrupt */
interrupt-names = "tx", "rx";
ti,hwmods = "mcbsp2";
+ dmas = <&sdma 33>,
+ <&sdma 34>;
+ dma-names = "tx", "rx";
};
timer1: timer@48028000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x48028000 0x400>;
interrupts = <37>;
ti,hwmods = "timer1";
pinctrl-single,function-mask = <0x3f>;
};
+ gpio1: gpio@4900c000 {
+ compatible = "ti,omap2-gpio";
+ reg = <0x4900c000 0x200>;
+ interrupts = <29>;
+ ti,hwmods = "gpio1";
+ ti,gpio-always-on;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ gpio2: gpio@4900e000 {
+ compatible = "ti,omap2-gpio";
+ reg = <0x4900e000 0x200>;
+ interrupts = <30>;
+ ti,hwmods = "gpio2";
+ ti,gpio-always-on;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ gpio3: gpio@49010000 {
+ compatible = "ti,omap2-gpio";
+ reg = <0x49010000 0x200>;
+ interrupts = <31>;
+ ti,hwmods = "gpio3";
+ ti,gpio-always-on;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ gpio4: gpio@49012000 {
+ compatible = "ti,omap2-gpio";
+ reg = <0x49012000 0x200>;
+ interrupts = <32>;
+ ti,hwmods = "gpio4";
+ ti,gpio-always-on;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ gpio5: gpio@480b6000 {
+ compatible = "ti,omap2-gpio";
+ reg = <0x480b6000 0x200>;
+ interrupts = <33>;
+ ti,hwmods = "gpio5";
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ gpmc: gpmc@6e000000 {
+ compatible = "ti,omap2430-gpmc";
+ reg = <0x6e000000 0x1000>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ interrupts = <20>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <4>;
+ ti,hwmods = "gpmc";
+ };
+
mcbsp1: mcbsp@48074000 {
compatible = "ti,omap2430-mcbsp";
reg = <0x48074000 0xff>;
interrupt-names = "common", "tx", "rx", "rx_overflow";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp1";
+ dmas = <&sdma 31>,
+ <&sdma 32>;
+ dma-names = "tx", "rx";
};
mcbsp2: mcbsp@48076000 {
interrupt-names = "common", "tx", "rx";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp2";
+ dmas = <&sdma 33>,
+ <&sdma 34>;
+ dma-names = "tx", "rx";
};
mcbsp3: mcbsp@4808c000 {
interrupt-names = "common", "tx", "rx";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp3";
+ dmas = <&sdma 17>,
+ <&sdma 18>;
+ dma-names = "tx", "rx";
};
mcbsp4: mcbsp@4808e000 {
interrupt-names = "common", "tx", "rx";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp4";
+ dmas = <&sdma 19>,
+ <&sdma 20>;
+ dma-names = "tx", "rx";
};
mcbsp5: mcbsp@48096000 {
interrupt-names = "common", "tx", "rx";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp5";
+ dmas = <&sdma 21>,
+ <&sdma 22>;
+ dma-names = "tx", "rx";
};
timer1: timer@49018000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap2420-timer";
reg = <0x49018000 0x400>;
interrupts = <37>;
ti,hwmods = "timer1";
model = "TI OMAP3 BeagleBoard xM";
compatible = "ti,omap3-beagle-xm, ti,omap3-beagle", "ti,omap3";
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
memory {
device_type = "memory";
reg = <0x80000000 0x20000000>; /* 512 MB */
leds {
compatible = "gpio-leds";
- pmu_stat {
- label = "beagleboard::pmu_stat";
- gpios = <&twl_gpio 19 0>; /* LEDB */
- };
heartbeat {
label = "beagleboard::usr0";
};
};
+ pwmleds {
+ compatible = "pwm-leds";
+
+ pmu_stat {
+ label = "beagleboard::pmu_stat";
+ pwms = <&twl_pwmled 1 7812500>;
+ max-brightness = <127>;
+ };
+ };
+
sound {
compatible = "ti,omap-twl4030";
ti,model = "omap3beagle";
*/
ti,pulldowns = <0x03a1c4>;
};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ mode = <3>;
+ power = <50>;
+};
*/
/dts-v1/;
-/include/ "omap3.dtsi"
+/include/ "omap34xx.dtsi"
/ {
model = "TI OMAP3 BeagleBoard";
compatible = "ti,omap3-beagle", "ti,omap3";
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>; /* 256 MB */
--- /dev/null
+/*
+ * Author: Anil Kumar <anilk4.v@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap34xx.dtsi"
+/ {
+ model = "TimLL OMAP3 Devkit8000";
+ compatible = "timll,omap3-devkit8000", "ti,omap3";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ heartbeat {
+ label = "devkit8000::led1";
+ gpios = <&gpio6 26 0>; /* 186 -> LED1 */
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+
+ mmc {
+ label = "devkit8000::led2";
+ gpios = <&gpio6 3 0>; /* 163 -> LED2 */
+ default-state = "on";
+ linux,default-trigger = "none";
+ };
+
+ usr {
+ label = "devkit8000::led3";
+ gpios = <&gpio6 4 0>; /* 164 -> LED3 */
+ default-state = "on";
+ linux,default-trigger = "usr";
+ };
+
+ };
+
+ sound {
+ compatible = "ti,omap-twl4030";
+ ti,model = "devkit8000";
+
+ ti,mcbsp = <&mcbsp2>;
+ ti,codec = <&twl_audio>;
+ ti,audio-routing =
+ "Ext Spk", "PREDRIVEL",
+ "Ext Spk", "PREDRIVER",
+ "MAINMIC", "Main Mic",
+ "Main Mic", "Mic Bias 1";
+ };
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ codec {
+ };
+ };
+ };
+};
+
+&i2c2 {
+ status = "disabled";
+};
+
+&i2c3 {
+ status = "disabled";
+};
+
+/include/ "twl4030.dtsi"
+
+&mmc1 {
+ vmmc-supply = <&vmmc1>;
+ vmmc_aux-supply = <&vsim>;
+ bus-width = <8>;
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&wdt2 {
+ status = "disabled";
+};
+
+&mcbsp1 {
+ status = "disabled";
+};
+
+&mcbsp3 {
+ status = "disabled";
+};
+
+&mcbsp4 {
+ status = "disabled";
+};
+
+&mcbsp5 {
+ status = "disabled";
+};
+
+&gpmc {
+ ranges = <0 0 0x30000000 0x04>; /* CS0: NAND */
+
+ nand@0,0 {
+ reg = <0 0 0>; /* CS0, offset 0 */
+ nand-bus-width = <16>;
+
+ gpmc,sync-clk = <0>;
+ gpmc,cs-on = <0>;
+ gpmc,cs-rd-off = <44>;
+ gpmc,cs-wr-off = <44>;
+ gpmc,adv-on = <6>;
+ gpmc,adv-rd-off = <34>;
+ gpmc,adv-wr-off = <44>;
+ gpmc,we-off = <40>;
+ gpmc,oe-off = <54>;
+ gpmc,access = <64>;
+ gpmc,rd-cycle = <82>;
+ gpmc,wr-cycle = <82>;
+ gpmc,wr-access = <40>;
+ gpmc,wr-data-mux-bus = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ x-loader@0 {
+ label = "X-Loader";
+ reg = <0 0x80000>;
+ };
+
+ bootloaders@80000 {
+ label = "U-Boot";
+ reg = <0x80000 0x1e0000>;
+ };
+
+ bootloaders_env@260000 {
+ label = "U-Boot Env";
+ reg = <0x260000 0x20000>;
+ };
+
+ kernel@280000 {
+ label = "Kernel";
+ reg = <0x280000 0x400000>;
+ };
+
+ filesystem@680000 {
+ label = "File System";
+ reg = <0x680000 0xf980000>;
+ };
+ };
+};
*/
/dts-v1/;
-/include/ "omap3.dtsi"
+/include/ "omap34xx.dtsi"
/ {
model = "TI OMAP3 EVM (OMAP3530, AM/DM37x)";
compatible = "ti,omap3-evm", "ti,omap3";
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
memory {
device_type = "memory";
reg = <0x80000000 0x10000000>; /* 256 MB */
&twl_gpio {
ti,use-leds;
};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ mode = <3>;
+ power = <50>;
+};
--- /dev/null
+/*
+ * Device Tree Source for IGEP Technology devices
+ *
+ * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
+ * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap34xx.dtsi"
+
+/ {
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>; /* 512 MB */
+ };
+
+ sound {
+ compatible = "ti,omap-twl4030";
+ ti,model = "igep2";
+ ti,mcbsp = <&mcbsp2>;
+ ti,codec = <&twl_audio>;
+ };
+};
+
+&omap3_pmx_core {
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ 0x152 0x100 /* uart1_rx.uart1_rx INPUT | MODE0 */
+ 0x14c 0 /* uart1_tx.uart1_tx OUTPUT | MODE0 */
+ >;
+ };
+
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ 0x14a 0x100 /* uart2_rx.uart2_rx INPUT | MODE0 */
+ 0x148 0 /* uart2_tx.uart2_tx OUTPUT | MODE0 */
+ >;
+ };
+
+ uart3_pins: pinmux_uart3_pins {
+ pinctrl-single,pins = <
+ 0x16e 0x100 /* uart3_rx.uart3_rx INPUT | MODE0 */
+ 0x170 0 /* uart3_tx.uart3_tx OUTPUT | MODE0 */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ 0x114 0x0118 /* sdmmc1_clk.sdmmc1_clk INPUT PULLUP | MODE 0 */
+ 0x116 0x0118 /* sdmmc1_cmd.sdmmc1_cmd INPUT PULLUP | MODE 0 */
+ 0x118 0x0118 /* sdmmc1_dat0.sdmmc1_dat0 INPUT PULLUP | MODE 0 */
+ 0x11a 0x0118 /* sdmmc1_dat1.sdmmc1_dat1 INPUT PULLUP | MODE 0 */
+ 0x11c 0x0118 /* sdmmc1_dat2.sdmmc1_dat2 INPUT PULLUP | MODE 0 */
+ 0x11e 0x0118 /* sdmmc1_dat3.sdmmc1_dat3 INPUT PULLUP | MODE 0 */
+ 0x120 0x0100 /* sdmmc1_dat4.sdmmc1_dat4 INPUT | MODE 0 */
+ 0x122 0x0100 /* sdmmc1_dat5.sdmmc1_dat5 INPUT | MODE 0 */
+ 0x124 0x0100 /* sdmmc1_dat6.sdmmc1_dat6 INPUT | MODE 0 */
+ 0x126 0x0100 /* sdmmc1_dat7.sdmmc1_dat7 INPUT | MODE 0 */
+ >;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ codec {
+ };
+ };
+ };
+};
+
+/include/ "twl4030.dtsi"
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <&vmmc1>;
+ vmmc_aux-supply = <&vsim>;
+ bus-width = <8>;
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+};
+
+&twl_gpio {
+ ti,use-leds;
+};
--- /dev/null
+/*
+ * Device Tree Source for IGEPv2 board
+ *
+ * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
+ * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/include/ "omap3-igep.dtsi"
+
+/ {
+ model = "IGEPv2";
+ compatible = "isee,omap3-igep0020", "ti,omap3";
+
+ leds {
+ compatible = "gpio-leds";
+ boot {
+ label = "omap3:green:boot";
+ gpios = <&gpio1 26 0>;
+ default-state = "on";
+ };
+
+ user0 {
+ label = "omap3:red:user0";
+ gpios = <&gpio1 27 0>;
+ default-state = "off";
+ };
+
+ user1 {
+ label = "omap3:red:user1";
+ gpios = <&gpio1 28 0>;
+ default-state = "off";
+ };
+
+ user2 {
+ label = "omap3:green:user1";
+ gpios = <&twl_gpio 19 1>;
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+
+ /*
+ * Display monitor features are burnt in the EEPROM
+ * as EDID data.
+ */
+ eeprom@50 {
+ compatible = "ti,eeprom";
+ reg = <0x50>;
+ };
+};
--- /dev/null
+/*
+ * Device Tree Source for IGEP COM Module
+ *
+ * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
+ * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/include/ "omap3-igep.dtsi"
+
+/ {
+ model = "IGEP COM Module";
+ compatible = "isee,omap3-igep0030", "ti,omap3";
+
+ leds {
+ compatible = "gpio-leds";
+ boot {
+ label = "omap3:green:boot";
+ gpios = <&twl_gpio 13 1>;
+ default-state = "on";
+ };
+
+ user0 {
+ label = "omap3:red:user0";
+ gpios = <&twl_gpio 18 1>; /* LEDA */
+ default-state = "off";
+ };
+
+ user1 {
+ label = "omap3:green:user1";
+ gpios = <&twl_gpio 19 1>; /* LEDB */
+ default-state = "off";
+ };
+
+ user2 {
+ label = "omap3:red:user1";
+ gpios = <&gpio1 16 1>;
+ default-state = "off";
+ };
+ };
+};
*/
/dts-v1/;
-/include/ "omap3.dtsi"
+/include/ "omap34xx.dtsi"
/ {
- leds {
- compatible = "gpio-leds";
+ pwmleds {
+ compatible = "pwm-leds";
+
overo {
label = "overo:blue:COM";
- gpios = <&twl_gpio 19 0>;
- linux,default-trigger = "mmc0";
+ pwms = <&twl_pwmled 1 7812500>;
+ max-brightness = <127>;
};
};
+
+ sound {
+ compatible = "ti,omap-twl4030";
+ ti,model = "overo";
+
+ ti,mcbsp = <&mcbsp2>;
+ ti,codec = <&twl_audio>;
+ };
};
&i2c1 {
reg = <0x48>;
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
interrupt-parent = <&intc>;
+
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ codec {
+ };
+ };
};
};
&twl_gpio {
ti,use-leds;
};
+
+&usb_otg_hs {
+ interface-type = <0>;
+ mode = <3>;
+ power = <50>;
+};
};
};
+ pmu {
+ compatible = "arm,cortex-a8-pmu";
+ interrupts = <3>;
+ ti,hwmods = "debugss";
+ };
+
/*
- * The soc node represents the soc top level view. It is uses for IPs
+ * The soc node represents the soc top level view. It is used for IPs
* that are not memory mapped in the MPU view or for the MPU itself.
*/
soc {
reg = <0x48200000 0x1000>;
};
+ sdma: dma-controller@48056000 {
+ compatible = "ti,omap3630-sdma", "ti,omap3430-sdma";
+ reg = <0x48056000 0x1000>;
+ interrupts = <12>,
+ <13>,
+ <14>,
+ <15>;
+ #dma-cells = <1>;
+ #dma-channels = <32>;
+ #dma-requests = <96>;
+ };
+
omap3_pmx_core: pinmux@48002030 {
compatible = "ti,omap3-padconf", "pinctrl-single";
reg = <0x48002030 0x05cc>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-single,register-width = <16>;
- pinctrl-single,function-mask = <0x7fff>;
+ pinctrl-single,function-mask = <0x7f1f>;
};
- omap3_pmx_wkup: pinmux@0x48002a58 {
+ omap3_pmx_wkup: pinmux@0x48002a00 {
compatible = "ti,omap3-padconf", "pinctrl-single";
- reg = <0x48002a58 0x5c>;
+ reg = <0x48002a00 0x5c>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-single,register-width = <16>;
- pinctrl-single,function-mask = <0x7fff>;
+ pinctrl-single,function-mask = <0x7f1f>;
};
gpio1: gpio@48310000 {
compatible = "ti,omap3-gpio";
+ reg = <0x48310000 0x200>;
+ interrupts = <29>;
ti,hwmods = "gpio1";
+ ti,gpio-always-on;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio2: gpio@49050000 {
compatible = "ti,omap3-gpio";
+ reg = <0x49050000 0x200>;
+ interrupts = <30>;
ti,hwmods = "gpio2";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio3: gpio@49052000 {
compatible = "ti,omap3-gpio";
+ reg = <0x49052000 0x200>;
+ interrupts = <31>;
ti,hwmods = "gpio3";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio4: gpio@49054000 {
compatible = "ti,omap3-gpio";
+ reg = <0x49054000 0x200>;
+ interrupts = <32>;
ti,hwmods = "gpio4";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio5: gpio@49056000 {
compatible = "ti,omap3-gpio";
+ reg = <0x49056000 0x200>;
+ interrupts = <33>;
ti,hwmods = "gpio5";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio6: gpio@49058000 {
compatible = "ti,omap3-gpio";
+ reg = <0x49058000 0x200>;
+ interrupts = <34>;
ti,hwmods = "gpio6";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
uart1: serial@4806a000 {
#size-cells = <0>;
ti,hwmods = "mcspi1";
ti,spi-num-cs = <4>;
+ dmas = <&sdma 35>,
+ <&sdma 36>,
+ <&sdma 37>,
+ <&sdma 38>,
+ <&sdma 39>,
+ <&sdma 40>,
+ <&sdma 41>,
+ <&sdma 42>;
+ dma-names = "tx0", "rx0", "tx1", "rx1",
+ "tx2", "rx2", "tx3", "rx3";
};
mcspi2: spi@4809a000 {
#size-cells = <0>;
ti,hwmods = "mcspi2";
ti,spi-num-cs = <2>;
+ dmas = <&sdma 43>,
+ <&sdma 44>,
+ <&sdma 45>,
+ <&sdma 46>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
};
mcspi3: spi@480b8000 {
#size-cells = <0>;
ti,hwmods = "mcspi3";
ti,spi-num-cs = <2>;
+ dmas = <&sdma 15>,
+ <&sdma 16>,
+ <&sdma 23>,
+ <&sdma 24>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
};
mcspi4: spi@480ba000 {
#size-cells = <0>;
ti,hwmods = "mcspi4";
ti,spi-num-cs = <1>;
+ dmas = <&sdma 70>, <&sdma 71>;
+ dma-names = "tx0", "rx0";
};
mmc1: mmc@4809c000 {
compatible = "ti,omap3-hsmmc";
ti,hwmods = "mmc1";
ti,dual-volt;
+ dmas = <&sdma 61>, <&sdma 62>;
+ dma-names = "tx", "rx";
};
mmc2: mmc@480b4000 {
compatible = "ti,omap3-hsmmc";
ti,hwmods = "mmc2";
+ dmas = <&sdma 47>, <&sdma 48>;
+ dma-names = "tx", "rx";
};
mmc3: mmc@480ad000 {
compatible = "ti,omap3-hsmmc";
ti,hwmods = "mmc3";
+ dmas = <&sdma 77>, <&sdma 78>;
+ dma-names = "tx", "rx";
};
wdt2: wdt@48314000 {
interrupt-names = "common", "tx", "rx";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp1";
+ dmas = <&sdma 31>,
+ <&sdma 32>;
+ dma-names = "tx", "rx";
};
mcbsp2: mcbsp@49022000 {
interrupt-names = "common", "tx", "rx", "sidetone";
ti,buffer-size = <1280>;
ti,hwmods = "mcbsp2", "mcbsp2_sidetone";
+ dmas = <&sdma 33>,
+ <&sdma 34>;
+ dma-names = "tx", "rx";
};
mcbsp3: mcbsp@49024000 {
interrupt-names = "common", "tx", "rx", "sidetone";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp3", "mcbsp3_sidetone";
+ dmas = <&sdma 17>,
+ <&sdma 18>;
+ dma-names = "tx", "rx";
};
mcbsp4: mcbsp@49026000 {
interrupt-names = "common", "tx", "rx";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp4";
+ dmas = <&sdma 19>,
+ <&sdma 20>;
+ dma-names = "tx", "rx";
};
mcbsp5: mcbsp@48096000 {
interrupt-names = "common", "tx", "rx";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp5";
+ dmas = <&sdma 21>,
+ <&sdma 22>;
+ dma-names = "tx", "rx";
};
timer1: timer@48318000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x48318000 0x400>;
interrupts = <37>;
ti,hwmods = "timer1";
};
timer2: timer@49032000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x49032000 0x400>;
interrupts = <38>;
ti,hwmods = "timer2";
};
timer3: timer@49034000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x49034000 0x400>;
interrupts = <39>;
ti,hwmods = "timer3";
};
timer4: timer@49036000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x49036000 0x400>;
interrupts = <40>;
ti,hwmods = "timer4";
};
timer5: timer@49038000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x49038000 0x400>;
interrupts = <41>;
ti,hwmods = "timer5";
};
timer6: timer@4903a000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x4903a000 0x400>;
interrupts = <42>;
ti,hwmods = "timer6";
};
timer7: timer@4903c000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x4903c000 0x400>;
interrupts = <43>;
ti,hwmods = "timer7";
};
timer8: timer@4903e000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x4903e000 0x400>;
interrupts = <44>;
ti,hwmods = "timer8";
};
timer9: timer@49040000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x49040000 0x400>;
interrupts = <45>;
ti,hwmods = "timer9";
};
timer10: timer@48086000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x48086000 0x400>;
interrupts = <46>;
ti,hwmods = "timer10";
};
timer11: timer@48088000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x48088000 0x400>;
interrupts = <47>;
ti,hwmods = "timer11";
};
timer12: timer@48304000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x48304000 0x400>;
interrupts = <95>;
ti,hwmods = "timer12";
};
};
+ gpmc: gpmc@6e000000 {
+ compatible = "ti,omap3430-gpmc";
+ ti,hwmods = "gpmc";
+ reg = <0x6e000000 0x02d0>;
+ interrupts = <20>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <4>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ };
+
+ usb_otg_hs: usb_otg_hs@480ab000 {
+ compatible = "ti,omap3-musb";
+ reg = <0x480ab000 0x1000>;
+ interrupts = <0 92 0x4>, <0 93 0x4>;
+ interrupt-names = "mc", "dma";
+ ti,hwmods = "usb_otg_hs";
+ usb-phy = <&usb2_phy>;
+ multipoint = <1>;
+ num-eps = <16>;
+ ram-bits = <12>;
+ };
};
};
--- /dev/null
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+/include/ "omap34xx.dtsi"
+
+/ {
+ model = "TI OMAP3430 SDP";
+ compatible = "ti,omap3430-sdp", "ti,omap3";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ };
+};
+
+/include/ "twl4030.dtsi"
+
+&mmc1 {
+ vmmc-supply = <&vmmc1>;
+ vmmc_aux-supply = <&vsim>;
+ bus-width = <8>;
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&gpmc {
+ ranges = <0 0 0x10000000 0x08000000>,
+ <1 0 0x28000000 0x08000000>,
+ <2 0 0x20000000 0x10000000>;
+
+ nor@0,0 {
+ compatible = "cfi-flash";
+ linux,mtd-name= "intel,pf48f6000m0y1be";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0 0 0x08000000>;
+ bank-width = <2>;
+
+ gpmc,mux-add-data = <2>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <186>;
+ gpmc,cs-wr-off-ns = <186>;
+ gpmc,adv-on-ns = <12>;
+ gpmc,adv-rd-off-ns = <48>;
+ gpmc,adv-wr-off-ns = <48>;
+ gpmc,oe-on-ns = <54>;
+ gpmc,oe-off-ns = <168>;
+ gpmc,we-on-ns = <54>;
+ gpmc,we-off-ns = <168>;
+ gpmc,rd-cycle-ns = <186>;
+ gpmc,wr-cycle-ns = <186>;
+ gpmc,access-ns = <114>;
+ gpmc,page-burst-access-ns = <6>;
+ gpmc,bus-turnaround-ns = <12>;
+ gpmc,cycle2cycle-delay-ns = <18>;
+ gpmc,wr-data-mux-bus-ns = <90>;
+ gpmc,wr-access-ns = <186>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-diffcsen;
+
+ partition@0 {
+ label = "bootloader-nor";
+ reg = <0 0x40000>;
+ };
+ partition@0x40000 {
+ label = "params-nor";
+ reg = <0x40000 0x40000>;
+ };
+ partition@0x80000 {
+ label = "kernel-nor";
+ reg = <0x80000 0x200000>;
+ };
+ partition@0x280000 {
+ label = "filesystem-nor";
+ reg = <0x240000 0x7d80000>;
+ };
+ };
+
+ nand@1,0 {
+ linux,mtd-name= "micron,mt29f1g08abb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <1 0 0x08000000>;
+ nand-bus-width = <8>;
+
+ ti,nand-ecc-opt = "sw";
+ gpmc,device-nand;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <36>;
+ gpmc,cs-wr-off-ns = <36>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <24>;
+ gpmc,adv-wr-off-ns = <36>;
+ gpmc,oe-on-ns = <6>;
+ gpmc,oe-off-ns = <48>;
+ gpmc,we-on-ns = <6>;
+ gpmc,we-off-ns = <30>;
+ gpmc,rd-cycle-ns = <72>;
+ gpmc,wr-cycle-ns = <72>;
+ gpmc,access-ns = <54>;
+ gpmc,wr-access-ns = <30>;
+
+ partition@0 {
+ label = "xloader-nand";
+ reg = <0 0x80000>;
+ };
+ partition@0x80000 {
+ label = "bootloader-nand";
+ reg = <0x80000 0x140000>;
+ };
+ partition@0x1c0000 {
+ label = "params-nand";
+ reg = <0x1c0000 0xc0000>;
+ };
+ partition@0x280000 {
+ label = "kernel-nand";
+ reg = <0x280000 0x500000>;
+ };
+ partition@0x780000 {
+ label = "filesystem-nand";
+ reg = <0x780000 0x7880000>;
+ };
+ };
+
+ onenand@2,0 {
+ linux,mtd-name= "samsung,kfm2g16q2m-deb8";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <2 0 0x10000000>;
+
+ gpmc,device-width = <2>;
+ gpmc,mux-add-data = <2>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <84>;
+ gpmc,cs-wr-off-ns = <72>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <18>;
+ gpmc,adv-wr-off-ns = <18>;
+ gpmc,oe-on-ns = <30>;
+ gpmc,oe-off-ns = <84>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <42>;
+ gpmc,rd-cycle-ns = <108>;
+ gpmc,wr-cycle-ns = <96>;
+ gpmc,access-ns = <78>;
+ gpmc,wr-data-mux-bus-ns = <30>;
+
+ partition@0 {
+ label = "xloader-onenand";
+ reg = <0 0x80000>;
+ };
+ partition@0x80000 {
+ label = "bootloader-onenand";
+ reg = <0x80000 0x40000>;
+ };
+ partition@0xc0000 {
+ label = "params-onenand";
+ reg = <0xc0000 0x20000>;
+ };
+ partition@0xe0000 {
+ label = "kernel-onenand";
+ reg = <0xe0000 0x200000>;
+ };
+ partition@0x2e0000 {
+ label = "filesystem-onenand";
+ reg = <0x2e0000 0xfd20000>;
+ };
+ };
+};
--- /dev/null
+/*
+ * Device Tree Source for OMAP34xx/OMAP35xx SoC
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "omap3.dtsi"
+
+/ {
+ cpus {
+ cpu@0 {
+ /* OMAP343x/OMAP35xx variants OPP1-5 */
+ operating-points = <
+ /* kHz uV */
+ 125000 975000
+ 250000 1075000
+ 500000 1200000
+ 550000 1270000
+ 600000 1350000
+ >;
+ clock-latency = <300000>; /* From legacy driver */
+ };
+ };
+};
serial3 = &uart4;
};
+ cpus {
+ /* OMAP3630/OMAP37xx 'standard device' variants OPP50 to OPP130 */
+ cpu@0 {
+ operating-points = <
+ /* kHz uV */
+ 300000 975000
+ 600000 1075000
+ 800000 1200000
+ >;
+ clock-latency = <300000>; /* From legacy driver */
+ };
+ };
+
ocp {
uart4: serial@49042000 {
compatible = "ti,omap3-uart";
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-/include/ "omap4-panda.dts"
+/dts-v1/;
+
+/include/ "omap443x.dtsi"
+/include/ "omap4-panda-common.dtsi"
/* Pandaboard Rev A4+ have external pullups on SCL & SDA */
&dss_hdmi_pins {
--- /dev/null
+/*
+ * Copyright (C) 2011-2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/include/ "elpida_ecb240abacn.dtsi"
+
+/ {
+ model = "TI OMAP4 PandaBoard";
+ compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>; /* 1 GB */
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ heartbeat {
+ label = "pandaboard::status1";
+ gpios = <&gpio1 7 0>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ mmc {
+ label = "pandaboard::status2";
+ gpios = <&gpio1 8 0>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
+ sound: sound {
+ compatible = "ti,abe-twl6040";
+ ti,model = "PandaBoard";
+
+ ti,mclk-freq = <38400000>;
+
+ ti,mcpdm = <&mcpdm>;
+
+ ti,twl6040 = <&twl6040>;
+
+ /* Audio routing */
+ ti,audio-routing =
+ "Headset Stereophone", "HSOL",
+ "Headset Stereophone", "HSOR",
+ "Ext Spk", "HFL",
+ "Ext Spk", "HFR",
+ "Line Out", "AUXL",
+ "Line Out", "AUXR",
+ "HSMIC", "Headset Mic",
+ "Headset Mic", "Headset Mic Bias",
+ "AFML", "Line In",
+ "AFMR", "Line In";
+ };
+};
+
+&omap4_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &twl6040_pins
+ &mcpdm_pins
+ &mcbsp1_pins
+ &dss_hdmi_pins
+ &tpd12s015_pins
+ >;
+
+ twl6040_pins: pinmux_twl6040_pins {
+ pinctrl-single,pins = <
+ 0xe0 0x3 /* hdq_sio.gpio_127 OUTPUT | MODE3 */
+ 0x160 0x100 /* sys_nirq2.sys_nirq2 INPUT | MODE0 */
+ >;
+ };
+
+ mcpdm_pins: pinmux_mcpdm_pins {
+ pinctrl-single,pins = <
+ 0xc6 0x108 /* abe_pdm_ul_data.abe_pdm_ul_data INPUT PULLDOWN | MODE0 */
+ 0xc8 0x108 /* abe_pdm_dl_data.abe_pdm_dl_data INPUT PULLDOWN | MODE0 */
+ 0xca 0x118 /* abe_pdm_frame.abe_pdm_frame INPUT PULLUP | MODE0 */
+ 0xcc 0x108 /* abe_pdm_lb_clk.abe_pdm_lb_clk INPUT PULLDOWN | MODE0 */
+ 0xce 0x108 /* abe_clks.abe_clks INPUT PULLDOWN | MODE0 */
+ >;
+ };
+
+ mcbsp1_pins: pinmux_mcbsp1_pins {
+ pinctrl-single,pins = <
+ 0xbe 0x100 /* abe_mcbsp1_clkx.abe_mcbsp1_clkx INPUT | MODE0 */
+ 0xc0 0x108 /* abe_mcbsp1_dr.abe_mcbsp1_dr INPUT PULLDOWN | MODE0 */
+ 0xc2 0x8 /* abe_mcbsp1_dx.abe_mcbsp1_dx OUTPUT PULLDOWN | MODE0 */
+ 0xc4 0x100 /* abe_mcbsp1_fsx.abe_mcbsp1_fsx INPUT | MODE0 */
+ >;
+ };
+
+ dss_hdmi_pins: pinmux_dss_hdmi_pins {
+ pinctrl-single,pins = <
+ 0x5a 0x118 /* hdmi_cec.hdmi_cec INPUT PULLUP | MODE 0 */
+ 0x5c 0x118 /* hdmi_scl.hdmi_scl INPUT PULLUP | MODE 0 */
+ 0x5e 0x118 /* hdmi_sda.hdmi_sda INPUT PULLUP | MODE 0 */
+ >;
+ };
+
+ tpd12s015_pins: pinmux_tpd12s015_pins {
+ pinctrl-single,pins = <
+ 0x22 0x3 /* gpmc_a17.gpio_41 OUTPUT | MODE3 */
+ 0x48 0x3 /* gpmc_nbe1.gpio_60 OUTPUT | MODE3 */
+ 0x58 0x10b /* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */
+ >;
+ };
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0xe2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */
+ 0xe4 0x118 /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ 0xe6 0x118 /* i2c2_scl PULLUP | INPUTENABLE | MODE0 */
+ 0xe8 0x118 /* i2c2_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ 0xea 0x118 /* i2c3_scl PULLUP | INPUTENABLE | MODE0 */
+ 0xec 0x118 /* i2c3_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c4_pins: pinmux_i2c4_pins {
+ pinctrl-single,pins = <
+ 0xee 0x118 /* i2c4_scl PULLUP | INPUTENABLE | MODE0 */
+ 0xf0 0x118 /* i2c4_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ clock-frequency = <400000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
+ interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */
+ interrupt-parent = <&gic>;
+ };
+
+ twl6040: twl@4b {
+ compatible = "ti,twl6040";
+ reg = <0x4b>;
+ /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
+ interrupts = <0 119 4>; /* IRQ_SYS_2N cascaded to gic */
+ interrupt-parent = <&gic>;
+ ti,audpwron-gpio = <&gpio4 31 0>; /* gpio line 127 */
+
+ vio-supply = <&v1v8>;
+ v2v1-supply = <&v2v1>;
+ enable-active-high;
+ };
+};
+
+/include/ "twl6030.dtsi"
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+
+ clock-frequency = <100000>;
+
+ /*
+ * Display monitor features are burnt in their EEPROM as EDID data.
+ * The EEPROM is connected as I2C slave device.
+ */
+ eeprom@50 {
+ compatible = "ti,eeprom";
+ reg = <0x50>;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+
+ clock-frequency = <400000>;
+};
+
+&mmc1 {
+ vmmc-supply = <&vmmc>;
+ bus-width = <8>;
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&mmc4 {
+ status = "disabled";
+};
+
+&mmc5 {
+ ti,non-removable;
+ bus-width = <4>;
+};
+
+&emif1 {
+ cs1-used;
+ device-handle = <&elpida_ECB240ABACN>;
+};
+
+&emif2 {
+ cs1-used;
+ device-handle = <&elpida_ECB240ABACN>;
+};
+
+&mcbsp2 {
+ status = "disabled";
+};
+
+&mcbsp3 {
+ status = "disabled";
+};
+
+&dmic {
+ status = "disabled";
+};
+
+&twl_usb_comparator {
+ usb-supply = <&vusb>;
+};
+
+&usb_otg_hs {
+ interface-type = <1>;
+ mode = <3>;
+ power = <50>;
+};
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-/include/ "omap4-panda.dts"
+/dts-v1/;
+
+/include/ "omap4460.dtsi"
+/include/ "omap4-panda-common.dtsi"
/* Audio routing is differnet between PandaBoard4430 and PandaBoardES */
&sound {
*/
/dts-v1/;
-/include/ "omap4.dtsi"
-/include/ "elpida_ecb240abacn.dtsi"
-
-/ {
- model = "TI OMAP4 PandaBoard";
- compatible = "ti,omap4-panda", "ti,omap4430", "ti,omap4";
-
- memory {
- device_type = "memory";
- reg = <0x80000000 0x40000000>; /* 1 GB */
- };
-
- leds {
- compatible = "gpio-leds";
- heartbeat {
- label = "pandaboard::status1";
- gpios = <&gpio1 7 0>;
- linux,default-trigger = "heartbeat";
- };
-
- mmc {
- label = "pandaboard::status2";
- gpios = <&gpio1 8 0>;
- linux,default-trigger = "mmc0";
- };
- };
-
- sound: sound {
- compatible = "ti,abe-twl6040";
- ti,model = "PandaBoard";
-
- ti,mclk-freq = <38400000>;
-
- ti,mcpdm = <&mcpdm>;
-
- ti,twl6040 = <&twl6040>;
-
- /* Audio routing */
- ti,audio-routing =
- "Headset Stereophone", "HSOL",
- "Headset Stereophone", "HSOR",
- "Ext Spk", "HFL",
- "Ext Spk", "HFR",
- "Line Out", "AUXL",
- "Line Out", "AUXR",
- "HSMIC", "Headset Mic",
- "Headset Mic", "Headset Mic Bias",
- "AFML", "Line In",
- "AFMR", "Line In";
- };
-};
-
-&omap4_pmx_core {
- pinctrl-names = "default";
- pinctrl-0 = <
- &twl6040_pins
- &mcpdm_pins
- &mcbsp1_pins
- &dss_hdmi_pins
- &tpd12s015_pins
- >;
-
- twl6040_pins: pinmux_twl6040_pins {
- pinctrl-single,pins = <
- 0xe0 0x3 /* hdq_sio.gpio_127 OUTPUT | MODE3 */
- 0x160 0x100 /* sys_nirq2.sys_nirq2 INPUT | MODE0 */
- >;
- };
-
- mcpdm_pins: pinmux_mcpdm_pins {
- pinctrl-single,pins = <
- 0xc6 0x108 /* abe_pdm_ul_data.abe_pdm_ul_data INPUT PULLDOWN | MODE0 */
- 0xc8 0x108 /* abe_pdm_dl_data.abe_pdm_dl_data INPUT PULLDOWN | MODE0 */
- 0xca 0x118 /* abe_pdm_frame.abe_pdm_frame INPUT PULLUP | MODE0 */
- 0xcc 0x108 /* abe_pdm_lb_clk.abe_pdm_lb_clk INPUT PULLDOWN | MODE0 */
- 0xce 0x108 /* abe_clks.abe_clks INPUT PULLDOWN | MODE0 */
- >;
- };
-
- mcbsp1_pins: pinmux_mcbsp1_pins {
- pinctrl-single,pins = <
- 0xbe 0x100 /* abe_mcbsp1_clkx.abe_mcbsp1_clkx INPUT | MODE0 */
- 0xc0 0x108 /* abe_mcbsp1_dr.abe_mcbsp1_dr INPUT PULLDOWN | MODE0 */
- 0xc2 0x8 /* abe_mcbsp1_dx.abe_mcbsp1_dx OUTPUT PULLDOWN | MODE0 */
- 0xc4 0x100 /* abe_mcbsp1_fsx.abe_mcbsp1_fsx INPUT | MODE0 */
- >;
- };
-
- dss_hdmi_pins: pinmux_dss_hdmi_pins {
- pinctrl-single,pins = <
- 0x5a 0x118 /* hdmi_cec.hdmi_cec INPUT PULLUP | MODE 0 */
- 0x5c 0x118 /* hdmi_scl.hdmi_scl INPUT PULLUP | MODE 0 */
- 0x5e 0x118 /* hdmi_sda.hdmi_sda INPUT PULLUP | MODE 0 */
- >;
- };
-
- tpd12s015_pins: pinmux_tpd12s015_pins {
- pinctrl-single,pins = <
- 0x22 0x3 /* gpmc_a17.gpio_41 OUTPUT | MODE3 */
- 0x48 0x3 /* gpmc_nbe1.gpio_60 OUTPUT | MODE3 */
- 0x58 0x10b /* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */
- >;
- };
-};
-
-&i2c1 {
- clock-frequency = <400000>;
-
- twl: twl@48 {
- reg = <0x48>;
- /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */
- interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */
- interrupt-parent = <&gic>;
- };
-
- twl6040: twl@4b {
- compatible = "ti,twl6040";
- reg = <0x4b>;
- /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
- interrupts = <0 119 4>; /* IRQ_SYS_2N cascaded to gic */
- interrupt-parent = <&gic>;
- ti,audpwron-gpio = <&gpio4 31 0>; /* gpio line 127 */
-
- vio-supply = <&v1v8>;
- v2v1-supply = <&v2v1>;
- enable-active-high;
- };
-};
-
-/include/ "twl6030.dtsi"
-
-&i2c2 {
- clock-frequency = <400000>;
-};
-
-&i2c3 {
- clock-frequency = <100000>;
-
- /*
- * Display monitor features are burnt in their EEPROM as EDID data.
- * The EEPROM is connected as I2C slave device.
- */
- eeprom@50 {
- compatible = "ti,eeprom";
- reg = <0x50>;
- };
-};
-
-&i2c4 {
- clock-frequency = <400000>;
-};
-
-&mmc1 {
- vmmc-supply = <&vmmc>;
- bus-width = <8>;
-};
-
-&mmc2 {
- status = "disabled";
-};
-
-&mmc3 {
- status = "disabled";
-};
-
-&mmc4 {
- status = "disabled";
-};
-
-&mmc5 {
- ti,non-removable;
- bus-width = <4>;
-};
-
-&emif1 {
- cs1-used;
- device-handle = <&elpida_ECB240ABACN>;
-};
-
-&emif2 {
- cs1-used;
- device-handle = <&elpida_ECB240ABACN>;
-};
-
-&mcbsp2 {
- status = "disabled";
-};
-
-&mcbsp3 {
- status = "disabled";
-};
-
-&dmic {
- status = "disabled";
-};
-
-&twl_usb_comparator {
- usb-supply = <&vusb>;
-};
+/include/ "omap443x.dtsi"
+/include/ "omap4-panda-common.dtsi"
*/
/dts-v1/;
-/include/ "omap4.dtsi"
+/include/ "omap443x.dtsi"
/include/ "elpida_ecb240abacn.dtsi"
/ {
};
};
+ pwmleds {
+ compatible = "pwm-leds";
+ kpad {
+ label = "omap4::keypad";
+ pwms = <&twl_pwm 0 7812500>;
+ max-brightness = <127>;
+ };
+
+ charging {
+ label = "omap4:green:chrg";
+ pwms = <&twl_pwmled 0 7812500>;
+ max-brightness = <255>;
+ };
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&twl_pwm 1 7812500>;
+ brightness-levels = <
+ 0 10 20 30 40
+ 50 60 70 80 90
+ 100 110 120 127
+ >;
+ default-brightness-level = <13>;
+ };
+
sound {
compatible = "ti,abe-twl6040";
ti,model = "SDP4430";
0x58 0x10b /* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */
>;
};
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0xe2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */
+ 0xe4 0x118 /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ 0xe6 0x118 /* i2c2_scl PULLUP | INPUTENABLE | MODE0 */
+ 0xe8 0x118 /* i2c2_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ 0xea 0x118 /* i2c3_scl PULLUP | INPUTENABLE | MODE0 */
+ 0xec 0x118 /* i2c3_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c4_pins: pinmux_i2c4_pins {
+ pinctrl-single,pins = <
+ 0xee 0x118 /* i2c4_scl PULLUP | INPUTENABLE | MODE0 */
+ 0xf0 0x118 /* i2c4_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
};
&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
clock-frequency = <400000>;
twl: twl@48 {
/include/ "twl6030.dtsi"
&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
clock-frequency = <400000>;
};
&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+
clock-frequency = <400000>;
/*
};
&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+
clock-frequency = <400000>;
/*
&twl_usb_comparator {
usb-supply = <&vusb>;
};
+
+&usb_otg_hs {
+ interface-type = <1>;
+ mode = <3>;
+ power = <50>;
+};
*/
/dts-v1/;
-/include/ "omap4.dtsi"
+/include/ "omap443x.dtsi"
/ {
model = "Variscite OMAP4 SOM";
#size-cells = <1>;
ranges;
ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
+ reg = <0x44000000 0x1000>,
+ <0x44800000 0x2000>,
+ <0x45000000 0x1000>;
+ interrupts = <0 9 0x4>,
+ <0 10 0x4>;
counter32k: counter@4a304000 {
compatible = "ti,omap-counter32k";
pinctrl-single,function-mask = <0x7fff>;
};
+ sdma: dma-controller@4a056000 {
+ compatible = "ti,omap4430-sdma";
+ reg = <0x4a056000 0x1000>;
+ interrupts = <0 12 0x4>,
+ <0 13 0x4>,
+ <0 14 0x4>,
+ <0 15 0x4>;
+ #dma-cells = <1>;
+ #dma-channels = <32>;
+ #dma-requests = <127>;
+ };
+
gpio1: gpio@4a310000 {
compatible = "ti,omap4-gpio";
reg = <0x4a310000 0x200>;
interrupts = <0 29 0x4>;
ti,hwmods = "gpio1";
+ ti,gpio-always-on;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio2: gpio@48055000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio3: gpio@48057000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio4: gpio@48059000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio5: gpio@4805b000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio6: gpio@4805d000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
+ };
+
+ gpmc: gpmc@50000000 {
+ compatible = "ti,omap4430-gpmc";
+ reg = <0x50000000 0x1000>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ interrupts = <0 20 0x4>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <4>;
+ ti,hwmods = "gpmc";
};
uart1: serial@4806a000 {
#size-cells = <0>;
ti,hwmods = "mcspi1";
ti,spi-num-cs = <4>;
+ dmas = <&sdma 35>,
+ <&sdma 36>,
+ <&sdma 37>,
+ <&sdma 38>,
+ <&sdma 39>,
+ <&sdma 40>,
+ <&sdma 41>,
+ <&sdma 42>;
+ dma-names = "tx0", "rx0", "tx1", "rx1",
+ "tx2", "rx2", "tx3", "rx3";
};
mcspi2: spi@4809a000 {
#size-cells = <0>;
ti,hwmods = "mcspi2";
ti,spi-num-cs = <2>;
+ dmas = <&sdma 43>,
+ <&sdma 44>,
+ <&sdma 45>,
+ <&sdma 46>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
};
mcspi3: spi@480b8000 {
#size-cells = <0>;
ti,hwmods = "mcspi3";
ti,spi-num-cs = <2>;
+ dmas = <&sdma 15>, <&sdma 16>;
+ dma-names = "tx0", "rx0";
};
mcspi4: spi@480ba000 {
#size-cells = <0>;
ti,hwmods = "mcspi4";
ti,spi-num-cs = <1>;
+ dmas = <&sdma 70>, <&sdma 71>;
+ dma-names = "tx0", "rx0";
};
mmc1: mmc@4809c000 {
ti,hwmods = "mmc1";
ti,dual-volt;
ti,needs-special-reset;
+ dmas = <&sdma 61>, <&sdma 62>;
+ dma-names = "tx", "rx";
};
mmc2: mmc@480b4000 {
interrupts = <0 86 0x4>;
ti,hwmods = "mmc2";
ti,needs-special-reset;
+ dmas = <&sdma 47>, <&sdma 48>;
+ dma-names = "tx", "rx";
};
mmc3: mmc@480ad000 {
interrupts = <0 94 0x4>;
ti,hwmods = "mmc3";
ti,needs-special-reset;
+ dmas = <&sdma 77>, <&sdma 78>;
+ dma-names = "tx", "rx";
};
mmc4: mmc@480d1000 {
interrupts = <0 96 0x4>;
ti,hwmods = "mmc4";
ti,needs-special-reset;
+ dmas = <&sdma 57>, <&sdma 58>;
+ dma-names = "tx", "rx";
};
mmc5: mmc@480d5000 {
interrupts = <0 59 0x4>;
ti,hwmods = "mmc5";
ti,needs-special-reset;
+ dmas = <&sdma 59>, <&sdma 60>;
+ dma-names = "tx", "rx";
};
wdt2: wdt@4a314000 {
reg-names = "mpu", "dma";
interrupts = <0 112 0x4>;
ti,hwmods = "mcpdm";
+ dmas = <&sdma 65>,
+ <&sdma 66>;
+ dma-names = "up_link", "dn_link";
};
dmic: dmic@4012e000 {
reg-names = "mpu", "dma";
interrupts = <0 114 0x4>;
ti,hwmods = "dmic";
+ dmas = <&sdma 67>;
+ dma-names = "up_link";
};
mcbsp1: mcbsp@40122000 {
interrupt-names = "common";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp1";
+ dmas = <&sdma 33>,
+ <&sdma 34>;
+ dma-names = "tx", "rx";
};
mcbsp2: mcbsp@40124000 {
interrupt-names = "common";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp2";
+ dmas = <&sdma 17>,
+ <&sdma 18>;
+ dma-names = "tx", "rx";
};
mcbsp3: mcbsp@40126000 {
interrupt-names = "common";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp3";
+ dmas = <&sdma 19>,
+ <&sdma 20>;
+ dma-names = "tx", "rx";
};
mcbsp4: mcbsp@48096000 {
interrupt-names = "common";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp4";
+ dmas = <&sdma 31>,
+ <&sdma 32>;
+ dma-names = "tx", "rx";
};
keypad: keypad@4a31c000 {
#size-cells = <1>;
ranges;
ti,hwmods = "ocp2scp_usb_phy";
+ usb2_phy: usb2phy@4a0ad080 {
+ compatible = "ti,omap-usb2";
+ reg = <0x4a0ad080 0x58>;
+ ctrl-module = <&omap_control_usb>;
+ };
};
timer1: timer@4a318000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x4a318000 0x80>;
interrupts = <0 37 0x4>;
ti,hwmods = "timer1";
};
timer2: timer@48032000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x48032000 0x80>;
interrupts = <0 38 0x4>;
ti,hwmods = "timer2";
};
timer3: timer@48034000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap4430-timer";
reg = <0x48034000 0x80>;
interrupts = <0 39 0x4>;
ti,hwmods = "timer3";
};
timer4: timer@48036000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap4430-timer";
reg = <0x48036000 0x80>;
interrupts = <0 40 0x4>;
ti,hwmods = "timer4";
};
timer5: timer@40138000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap4430-timer";
reg = <0x40138000 0x80>,
<0x49038000 0x80>;
interrupts = <0 41 0x4>;
};
timer6: timer@4013a000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap4430-timer";
reg = <0x4013a000 0x80>,
<0x4903a000 0x80>;
interrupts = <0 42 0x4>;
};
timer7: timer@4013c000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap4430-timer";
reg = <0x4013c000 0x80>,
<0x4903c000 0x80>;
interrupts = <0 43 0x4>;
};
timer8: timer@4013e000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap4430-timer";
reg = <0x4013e000 0x80>,
<0x4903e000 0x80>;
interrupts = <0 44 0x4>;
};
timer9: timer@4803e000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap4430-timer";
reg = <0x4803e000 0x80>;
interrupts = <0 45 0x4>;
ti,hwmods = "timer9";
};
timer10: timer@48086000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap3430-timer";
reg = <0x48086000 0x80>;
interrupts = <0 46 0x4>;
ti,hwmods = "timer10";
};
timer11: timer@48088000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap4430-timer";
reg = <0x48088000 0x80>;
interrupts = <0 47 0x4>;
ti,hwmods = "timer11";
interrupts = <0 77 0x4>;
};
};
+
+ omap_control_usb: omap-control-usb@4a002300 {
+ compatible = "ti,omap-control-usb";
+ reg = <0x4a002300 0x4>,
+ <0x4a00233c 0x4>;
+ reg-names = "control_dev_conf", "otghs_control";
+ ti,type = <1>;
+ };
+
+ usb_otg_hs: usb_otg_hs@4a0ab000 {
+ compatible = "ti,omap4-musb";
+ reg = <0x4a0ab000 0x7ff>;
+ interrupts = <0 92 0x4>, <0 93 0x4>;
+ interrupt-names = "mc", "dma";
+ ti,hwmods = "usb_otg_hs";
+ usb-phy = <&usb2_phy>;
+ multipoint = <1>;
+ num-eps = <16>;
+ ram-bits = <12>;
+ ti,has-mailbox;
+ };
};
};
--- /dev/null
+/*
+ * Device Tree Source for OMAP443x SoC
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/include/ "omap4.dtsi"
+
+/ {
+ cpus {
+ cpu@0 {
+ /* OMAP443x variants OPP50-OPPNT */
+ operating-points = <
+ /* kHz uV */
+ 300000 1025000
+ 600000 1200000
+ 800000 1313000
+ 1008000 1375000
+ >;
+ clock-latency = <300000>; /* From legacy driver */
+ };
+ };
+};
--- /dev/null
+/*
+ * Device Tree Source for OMAP4460 SoC
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+/include/ "omap4.dtsi"
+
+/ {
+ cpus {
+ /* OMAP446x 'standard device' variants OPP50 to OPPTurbo */
+ cpu@0 {
+ operating-points = <
+ /* kHz uV */
+ 350000 975000
+ 700000 1075000
+ 920000 1200000
+ >;
+ clock-latency = <300000>; /* From legacy driver */
+ };
+ };
+
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <0 54 0x4>,
+ <0 55 0x4>;
+ ti,hwmods = "debugss";
+ };
+};
memory {
device_type = "memory";
- reg = <0x80000000 0x80000000>; /* 2 GB */
+ reg = <0x80000000 0x7F000000>; /* 2032 MB */
};
vmmcsd_fixed: fixedregulator-mmcsd {
0x15a 0x100 /* abemcbsp2_clkx.abemcbsp2_clkx INPUT | MODE0 */
>;
};
+
+ i2c1_pins: pinmux_i2c1_pins {
+ pinctrl-single,pins = <
+ 0x1b2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */
+ 0x1b4 0x118 /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ 0x178 0x100 /* i2c2_scl INPUTENABLE | MODE0 */
+ 0x17a 0x100 /* i2c2_sda INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c3_pins: pinmux_i2c3_pins {
+ pinctrl-single,pins = <
+ 0x13a 0x100 /* i2c3_scl INPUTENABLE | MODE0 */
+ 0x13c 0x100 /* i2c3_sda INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c4_pins: pinmux_i2c4_pins {
+ pinctrl-single,pins = <
+ 0xb8 0x100 /* i2c4_scl INPUTENABLE | MODE0 */
+ 0xba 0x100 /* i2c4_sda INPUTENABLE | MODE0 */
+ >;
+ };
+
+ i2c5_pins: pinmux_i2c5_pins {
+ pinctrl-single,pins = <
+ 0x184 0x100 /* i2c5_scl INPUTENABLE | MODE0 */
+ 0x186 0x100 /* i2c5_sda INPUTENABLE | MODE0 */
+ >;
+ };
+
+ mcspi2_pins: pinmux_mcspi2_pins {
+ pinctrl-single,pins = <
+ 0xbc 0x100 /* MCSPI2_CLK INPUTENABLE | MODE0 */
+ 0xbe 0x100 /* MCSPI2_SIMO INPUTENABLE | MODE0 */
+ 0xc0 0x118 /* MCSPI2_SOMI PULLUP | INPUTENABLE | MODE0*/
+ 0xc2 0x0 /* MCSPI2_CS MODE0*/
+ >;
+ };
+
+ mcspi3_pins: pinmux_mcspi3_pins {
+ pinctrl-single,pins = <
+ 0x78 0x101 /* MCSPI2_SOMI INPUTENABLE | MODE1 */
+ 0x7a 0x101 /* MCSPI2_CS INPUTENABLE | MODE1 */
+ 0x7c 0x101 /* MCSPI2_SIMO INPUTENABLE | MODE1 */
+ 0x7e 0x101 /* MCSPI2_CLK INPUTENABLE | MODE1 */
+ >;
+ };
+
+ mcspi4_pins: pinmux_mcspi4_pins {
+ pinctrl-single,pins = <
+ 0x164 0x101 /* MCSPI2_CLK INPUTENABLE | MODE1 */
+ 0x168 0x101 /* MCSPI2_SIMO INPUTENABLE | MODE1 */
+ 0x16a 0x101 /* MCSPI2_SOMI INPUTENABLE | MODE1 */
+ 0x16c 0x101 /* MCSPI2_CS INPUTENABLE | MODE1 */
+ >;
+ };
};
&mmc1 {
status = "disabled";
};
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ clock-frequency = <400000>;
+};
+
&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
clock-frequency = <400000>;
/* Pressure Sensor */
};
};
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+
+ clock-frequency = <400000>;
+};
+
&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+
clock-frequency = <400000>;
/* Temperature Sensor */
};
};
+&i2c5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_pins>;
+
+ clock-frequency = <400000>;
+};
+
&keypad {
keypad,num-rows = <8>;
keypad,num-columns = <8>;
cs1-used;
device-handle = <&samsung_K3PE0E000B>;
};
+
+&mcspi1 {
+
+};
+
+&mcspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi2_pins>;
+};
+
+&mcspi3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi3_pins>;
+};
+
+&mcspi4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi4_pins>;
+};
/include/ "skeleton.dtsi"
/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
compatible = "ti,omap5";
interrupt-parent = <&gic>;
cpus {
cpu@0 {
compatible = "arm,cortex-a15";
- timer {
- compatible = "arm,armv7-timer";
- /* 14th PPI IRQ, active low level-sensitive */
- interrupts = <1 14 0x308>;
- clock-frequency = <6144000>;
- };
};
cpu@1 {
compatible = "arm,cortex-a15";
- timer {
- compatible = "arm,armv7-timer";
- /* 14th PPI IRQ, active low level-sensitive */
- interrupts = <1 14 0x308>;
- clock-frequency = <6144000>;
- };
};
};
+ timer {
+ compatible = "arm,armv7-timer";
+ /* PPI secure/nonsecure IRQ, active low level-sensitive */
+ interrupts = <1 13 0x308>,
+ <1 14 0x308>,
+ <1 11 0x308>,
+ <1 10 0x308>;
+ clock-frequency = <6144000>;
+ };
+
+ gic: interrupt-controller@48211000 {
+ compatible = "arm,cortex-a15-gic";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x48211000 0x1000>,
+ <0x48212000 0x1000>,
+ <0x48214000 0x2000>,
+ <0x48216000 0x2000>;
+ };
+
/*
* The soc node represents the soc top level view. It is uses for IPs
* that are not memory mapped in the MPU view or for the MPU itself.
#size-cells = <1>;
ranges;
ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
+ reg = <0x44000000 0x2000>,
+ <0x44800000 0x3000>,
+ <0x45000000 0x4000>;
+ interrupts = <0 9 0x4>,
+ <0 10 0x4>;
counter32k: counter@4ae04000 {
compatible = "ti,omap-counter32k";
pinctrl-single,function-mask = <0x7fff>;
};
- gic: interrupt-controller@48211000 {
- compatible = "arm,cortex-a15-gic";
- interrupt-controller;
- #interrupt-cells = <3>;
- reg = <0x48211000 0x1000>,
- <0x48212000 0x1000>;
+ sdma: dma-controller@4a056000 {
+ compatible = "ti,omap4430-sdma";
+ reg = <0x4a056000 0x1000>;
+ interrupts = <0 12 0x4>,
+ <0 13 0x4>,
+ <0 14 0x4>,
+ <0 15 0x4>;
+ #dma-cells = <1>;
+ #dma-channels = <32>;
+ #dma-requests = <127>;
};
gpio1: gpio@4ae10000 {
reg = <0x4ae10000 0x200>;
interrupts = <0 29 0x4>;
ti,hwmods = "gpio1";
+ ti,gpio-always-on;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio2: gpio@48055000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio3: gpio@48057000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio4: gpio@48059000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio5: gpio@4805b000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio6: gpio@4805d000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio7: gpio@48051000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio8: gpio@48053000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
+ };
+
+ gpmc: gpmc@50000000 {
+ compatible = "ti,omap4430-gpmc";
+ reg = <0x50000000 0x1000>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ interrupts = <0 20 0x4>;
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <4>;
+ ti,hwmods = "gpmc";
};
i2c1: i2c@48070000 {
ti,hwmods = "i2c5";
};
+ mcspi1: spi@48098000 {
+ compatible = "ti,omap4-mcspi";
+ reg = <0x48098000 0x200>;
+ interrupts = <0 65 0x4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi1";
+ ti,spi-num-cs = <4>;
+ dmas = <&sdma 35>,
+ <&sdma 36>,
+ <&sdma 37>,
+ <&sdma 38>,
+ <&sdma 39>,
+ <&sdma 40>,
+ <&sdma 41>,
+ <&sdma 42>;
+ dma-names = "tx0", "rx0", "tx1", "rx1",
+ "tx2", "rx2", "tx3", "rx3";
+ };
+
+ mcspi2: spi@4809a000 {
+ compatible = "ti,omap4-mcspi";
+ reg = <0x4809a000 0x200>;
+ interrupts = <0 66 0x4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi2";
+ ti,spi-num-cs = <2>;
+ dmas = <&sdma 43>,
+ <&sdma 44>,
+ <&sdma 45>,
+ <&sdma 46>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
+ };
+
+ mcspi3: spi@480b8000 {
+ compatible = "ti,omap4-mcspi";
+ reg = <0x480b8000 0x200>;
+ interrupts = <0 91 0x4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi3";
+ ti,spi-num-cs = <2>;
+ dmas = <&sdma 15>, <&sdma 16>;
+ dma-names = "tx0", "rx0";
+ };
+
+ mcspi4: spi@480ba000 {
+ compatible = "ti,omap4-mcspi";
+ reg = <0x480ba000 0x200>;
+ interrupts = <0 48 0x4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "mcspi4";
+ ti,spi-num-cs = <1>;
+ dmas = <&sdma 70>, <&sdma 71>;
+ dma-names = "tx0", "rx0";
+ };
+
uart1: serial@4806a000 {
compatible = "ti,omap4-uart";
reg = <0x4806a000 0x100>;
ti,hwmods = "mmc1";
ti,dual-volt;
ti,needs-special-reset;
+ dmas = <&sdma 61>, <&sdma 62>;
+ dma-names = "tx", "rx";
};
mmc2: mmc@480b4000 {
interrupts = <0 86 0x4>;
ti,hwmods = "mmc2";
ti,needs-special-reset;
+ dmas = <&sdma 47>, <&sdma 48>;
+ dma-names = "tx", "rx";
};
mmc3: mmc@480ad000 {
interrupts = <0 94 0x4>;
ti,hwmods = "mmc3";
ti,needs-special-reset;
+ dmas = <&sdma 77>, <&sdma 78>;
+ dma-names = "tx", "rx";
};
mmc4: mmc@480d1000 {
interrupts = <0 96 0x4>;
ti,hwmods = "mmc4";
ti,needs-special-reset;
+ dmas = <&sdma 57>, <&sdma 58>;
+ dma-names = "tx", "rx";
};
mmc5: mmc@480d5000 {
interrupts = <0 59 0x4>;
ti,hwmods = "mmc5";
ti,needs-special-reset;
+ dmas = <&sdma 59>, <&sdma 60>;
+ dma-names = "tx", "rx";
};
keypad: keypad@4ae1c000 {
compatible = "ti,omap4-keypad";
+ reg = <0x4ae1c000 0x400>;
ti,hwmods = "kbd";
};
reg-names = "mpu", "dma";
interrupts = <0 112 0x4>;
ti,hwmods = "mcpdm";
+ dmas = <&sdma 65>,
+ <&sdma 66>;
+ dma-names = "up_link", "dn_link";
};
dmic: dmic@4012e000 {
reg-names = "mpu", "dma";
interrupts = <0 114 0x4>;
ti,hwmods = "dmic";
+ dmas = <&sdma 67>;
+ dma-names = "up_link";
};
mcbsp1: mcbsp@40122000 {
interrupt-names = "common";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp1";
+ dmas = <&sdma 33>,
+ <&sdma 34>;
+ dma-names = "tx", "rx";
};
mcbsp2: mcbsp@40124000 {
interrupt-names = "common";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp2";
+ dmas = <&sdma 17>,
+ <&sdma 18>;
+ dma-names = "tx", "rx";
};
mcbsp3: mcbsp@40126000 {
interrupt-names = "common";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp3";
+ dmas = <&sdma 19>,
+ <&sdma 20>;
+ dma-names = "tx", "rx";
};
timer1: timer@4ae18000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x4ae18000 0x80>;
interrupts = <0 37 0x4>;
ti,hwmods = "timer1";
};
timer2: timer@48032000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x48032000 0x80>;
interrupts = <0 38 0x4>;
ti,hwmods = "timer2";
};
timer3: timer@48034000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x48034000 0x80>;
interrupts = <0 39 0x4>;
ti,hwmods = "timer3";
};
timer4: timer@48036000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x48036000 0x80>;
interrupts = <0 40 0x4>;
ti,hwmods = "timer4";
};
timer5: timer@40138000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x40138000 0x80>,
<0x49038000 0x80>;
interrupts = <0 41 0x4>;
};
timer6: timer@4013a000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x4013a000 0x80>,
<0x4903a000 0x80>;
interrupts = <0 42 0x4>;
};
timer7: timer@4013c000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x4013c000 0x80>,
<0x4903c000 0x80>;
interrupts = <0 43 0x4>;
};
timer8: timer@4013e000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x4013e000 0x80>,
<0x4903e000 0x80>;
interrupts = <0 44 0x4>;
};
timer9: timer@4803e000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x4803e000 0x80>;
interrupts = <0 45 0x4>;
ti,hwmods = "timer9";
};
timer10: timer@48086000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x48086000 0x80>;
interrupts = <0 46 0x4>;
ti,hwmods = "timer10";
};
timer11: timer@48088000 {
- compatible = "ti,omap2-timer";
+ compatible = "ti,omap5430-timer";
reg = <0x48088000 0x80>;
interrupts = <0 47 0x4>;
ti,hwmods = "timer11";
ti,timer-pwm;
};
+ wdt2: wdt@4ae14000 {
+ compatible = "ti,omap5-wdt", "ti,omap3-wdt";
+ reg = <0x4ae14000 0x80>;
+ interrupts = <0 80 0x4>;
+ ti,hwmods = "wd_timer2";
+ };
+
emif1: emif@0x4c000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif1";
hw-caps-ll-interface;
hw-caps-temp-alert;
};
+
+ omap_control_usb: omap-control-usb@4a002300 {
+ compatible = "ti,omap-control-usb";
+ reg = <0x4a002300 0x4>,
+ <0x4a002370 0x4>;
+ reg-names = "control_dev_conf", "phy_power_usb";
+ ti,type = <2>;
+ };
+
+ omap_dwc3@4a020000 {
+ compatible = "ti,dwc3";
+ ti,hwmods = "usb_otg_ss";
+ reg = <0x4a020000 0x1000>;
+ interrupts = <0 93 4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ utmi-mode = <2>;
+ ranges;
+ dwc3@4a030000 {
+ compatible = "synopsys,dwc3";
+ reg = <0x4a030000 0x1000>;
+ interrupts = <0 92 4>;
+ usb-phy = <&usb2_phy>, <&usb3_phy>;
+ tx-fifo-resize;
+ };
+ };
+
+ ocp2scp {
+ compatible = "ti,omap-ocp2scp";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ ti,hwmods = "ocp2scp1";
+ usb2_phy: usb2phy@4a084000 {
+ compatible = "ti,omap-usb2";
+ reg = <0x4a084000 0x7c>;
+ ctrl-module = <&omap_control_usb>;
+ };
+
+ usb3_phy: usb3phy@4a084400 {
+ compatible = "ti,omap-usb3";
+ reg = <0x4a084400 0x80>,
+ <0x4a084800 0x64>,
+ <0x4a084c00 0x40>;
+ reg-names = "phy_rx", "phy_tx", "pll_ctrl";
+ ctrl-module = <&omap_control_usb>;
+ };
+ };
};
};
reg = <0x80000000 0x40000000>;
};
+ pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ clk1_out_pw4 {
+ nvidia,pins = "clk1_out_pw4";
+ nvidia,function = "extperiph1";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ dap1_din_pn1 {
+ nvidia,pins = "dap1_din_pn1";
+ nvidia,function = "i2s0";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ dap1_dout_pn2 {
+ nvidia,pins = "dap1_dout_pn2",
+ "dap1_fs_pn0",
+ "dap1_sclk_pn3";
+ nvidia,function = "i2s0";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ dap2_din_pa4 {
+ nvidia,pins = "dap2_din_pa4";
+ nvidia,function = "i2s1";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ dap2_dout_pa5 {
+ nvidia,pins = "dap2_dout_pa5",
+ "dap2_fs_pa2",
+ "dap2_sclk_pa3";
+ nvidia,function = "i2s1";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ dap4_din_pp5 {
+ nvidia,pins = "dap4_din_pp5",
+ "dap4_dout_pp6",
+ "dap4_fs_pp4",
+ "dap4_sclk_pp7";
+ nvidia,function = "i2s3";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ dvfs_pwm_px0 {
+ nvidia,pins = "dvfs_pwm_px0",
+ "dvfs_clk_px2";
+ nvidia,function = "cldvfs";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ ulpi_clk_py0 {
+ nvidia,pins = "ulpi_clk_py0",
+ "ulpi_data0_po1",
+ "ulpi_data1_po2",
+ "ulpi_data2_po3",
+ "ulpi_data3_po4",
+ "ulpi_data4_po5",
+ "ulpi_data5_po6",
+ "ulpi_data6_po7",
+ "ulpi_data7_po0";
+ nvidia,function = "ulpi";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ ulpi_dir_py1 {
+ nvidia,pins = "ulpi_dir_py1",
+ "ulpi_nxt_py2";
+ nvidia,function = "ulpi";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ ulpi_stp_py3 {
+ nvidia,pins = "ulpi_stp_py3";
+ nvidia,function = "ulpi";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ cam_i2c_scl_pbb1 {
+ nvidia,pins = "cam_i2c_scl_pbb1",
+ "cam_i2c_sda_pbb2";
+ nvidia,function = "i2c3";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ nvidia,lock = <0>;
+ nvidia,open-drain = <0>;
+ };
+ cam_mclk_pcc0 {
+ nvidia,pins = "cam_mclk_pcc0",
+ "pbb0";
+ nvidia,function = "vi_alt3";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ nvidia,lock = <0>;
+ };
+ gen2_i2c_scl_pt5 {
+ nvidia,pins = "gen2_i2c_scl_pt5",
+ "gen2_i2c_sda_pt6";
+ nvidia,function = "i2c2";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ nvidia,lock = <0>;
+ nvidia,open-drain = <0>;
+ };
+ gmi_a16_pj7 {
+ nvidia,pins = "gmi_a16_pj7";
+ nvidia,function = "uartd";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ gmi_a17_pb0 {
+ nvidia,pins = "gmi_a17_pb0",
+ "gmi_a18_pb1";
+ nvidia,function = "uartd";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ gmi_a19_pk7 {
+ nvidia,pins = "gmi_a19_pk7";
+ nvidia,function = "uartd";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ gmi_ad5_pg5 {
+ nvidia,pins = "gmi_ad5_pg5",
+ "gmi_cs6_n_pi3",
+ "gmi_wr_n_pi0";
+ nvidia,function = "spi4";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ gmi_ad6_pg6 {
+ nvidia,pins = "gmi_ad6_pg6",
+ "gmi_ad7_pg7";
+ nvidia,function = "spi4";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ gmi_ad12_ph4 {
+ nvidia,pins = "gmi_ad12_ph4";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ gmi_ad9_ph1 {
+ nvidia,pins = "gmi_ad9_ph1";
+ nvidia,function = "pwm1";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ gmi_cs1_n_pj2 {
+ nvidia,pins = "gmi_cs1_n_pj2",
+ "gmi_oe_n_pi1";
+ nvidia,function = "soc";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ clk2_out_pw5 {
+ nvidia,pins = "clk2_out_pw5";
+ nvidia,function = "extperiph2";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ sdmmc1_clk_pz0 {
+ nvidia,pins = "sdmmc1_clk_pz0";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ sdmmc1_cmd_pz1 {
+ nvidia,pins = "sdmmc1_cmd_pz1",
+ "sdmmc1_dat0_py7",
+ "sdmmc1_dat1_py6",
+ "sdmmc1_dat2_py5",
+ "sdmmc1_dat3_py4";
+ nvidia,function = "sdmmc1";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ sdmmc1_wp_n_pv3 {
+ nvidia,pins = "sdmmc1_wp_n_pv3";
+ nvidia,function = "spi4";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ sdmmc3_clk_pa6 {
+ nvidia,pins = "sdmmc3_clk_pa6";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ sdmmc3_cmd_pa7 {
+ nvidia,pins = "sdmmc3_cmd_pa7",
+ "sdmmc3_dat0_pb7",
+ "sdmmc3_dat1_pb6",
+ "sdmmc3_dat2_pb5",
+ "sdmmc3_dat3_pb4",
+ "kb_col4_pq4",
+ "sdmmc3_clk_lb_out_pee4",
+ "sdmmc3_clk_lb_in_pee5";
+ nvidia,function = "sdmmc3";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ sdmmc4_clk_pcc4 {
+ nvidia,pins = "sdmmc4_clk_pcc4";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ sdmmc4_cmd_pt7 {
+ nvidia,pins = "sdmmc4_cmd_pt7",
+ "sdmmc4_dat0_paa0",
+ "sdmmc4_dat1_paa1",
+ "sdmmc4_dat2_paa2",
+ "sdmmc4_dat3_paa3",
+ "sdmmc4_dat4_paa4",
+ "sdmmc4_dat5_paa5",
+ "sdmmc4_dat6_paa6",
+ "sdmmc4_dat7_paa7";
+ nvidia,function = "sdmmc4";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ clk_32k_out_pa0 {
+ nvidia,pins = "clk_32k_out_pa0";
+ nvidia,function = "blink";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ kb_col0_pq0 {
+ nvidia,pins = "kb_col0_pq0",
+ "kb_col1_pq1",
+ "kb_col2_pq2",
+ "kb_row0_pr0",
+ "kb_row1_pr1",
+ "kb_row2_pr2";
+ nvidia,function = "kbc";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ dap3_din_pp1 {
+ nvidia,pins = "dap3_din_pp1",
+ "dap3_sclk_pp3";
+ nvidia,function = "displayb";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <0>;
+ };
+ pv0 {
+ nvidia,pins = "pv0";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <0>;
+ };
+ kb_row7_pr7 {
+ nvidia,pins = "kb_row7_pr7";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ kb_row10_ps2 {
+ nvidia,pins = "kb_row10_ps2";
+ nvidia,function = "uarta";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ kb_row9_ps1 {
+ nvidia,pins = "kb_row9_ps1";
+ nvidia,function = "uarta";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ pwr_i2c_scl_pz6 {
+ nvidia,pins = "pwr_i2c_scl_pz6",
+ "pwr_i2c_sda_pz7";
+ nvidia,function = "i2cpwr";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ nvidia,lock = <0>;
+ nvidia,open-drain = <0>;
+ };
+ sys_clk_req_pz5 {
+ nvidia,pins = "sys_clk_req_pz5";
+ nvidia,function = "sysclk";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ core_pwr_req {
+ nvidia,pins = "core_pwr_req";
+ nvidia,function = "pwron";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ cpu_pwr_req {
+ nvidia,pins = "cpu_pwr_req";
+ nvidia,function = "cpu";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ pwr_int_n {
+ nvidia,pins = "pwr_int_n";
+ nvidia,function = "pmi";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ reset_out_n {
+ nvidia,pins = "reset_out_n";
+ nvidia,function = "reset_out_n";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ clk3_out_pee0 {
+ nvidia,pins = "clk3_out_pee0";
+ nvidia,function = "extperiph3";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ gen1_i2c_scl_pc4 {
+ nvidia,pins = "gen1_i2c_scl_pc4",
+ "gen1_i2c_sda_pc5";
+ nvidia,function = "i2c1";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ nvidia,lock = <0>;
+ nvidia,open-drain = <0>;
+ };
+ uart2_cts_n_pj5 {
+ nvidia,pins = "uart2_cts_n_pj5";
+ nvidia,function = "uartb";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ uart2_rts_n_pj6 {
+ nvidia,pins = "uart2_rts_n_pj6";
+ nvidia,function = "uartb";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ uart2_rxd_pc3 {
+ nvidia,pins = "uart2_rxd_pc3";
+ nvidia,function = "irda";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ uart2_txd_pc2 {
+ nvidia,pins = "uart2_txd_pc2";
+ nvidia,function = "irda";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ uart3_cts_n_pa1 {
+ nvidia,pins = "uart3_cts_n_pa1",
+ "uart3_rxd_pw7";
+ nvidia,function = "uartc";
+ nvidia,pull = <0>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ uart3_rts_n_pc0 {
+ nvidia,pins = "uart3_rts_n_pc0",
+ "uart3_txd_pw6";
+ nvidia,function = "uartc";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ owr {
+ nvidia,pins = "owr";
+ nvidia,function = "owr";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ hdmi_cec_pee3 {
+ nvidia,pins = "hdmi_cec_pee3";
+ nvidia,function = "cec";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ nvidia,lock = <0>;
+ nvidia,open-drain = <0>;
+ };
+ ddc_scl_pv4 {
+ nvidia,pins = "ddc_scl_pv4",
+ "ddc_sda_pv5";
+ nvidia,function = "i2c4";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ nvidia,lock = <0>;
+ nvidia,rcv-sel = <1>;
+ };
+ spdif_in_pk6 {
+ nvidia,pins = "spdif_in_pk6";
+ nvidia,function = "usb";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ nvidia,lock = <0>;
+ };
+ usb_vbus_en0_pn4 {
+ nvidia,pins = "usb_vbus_en0_pn4";
+ nvidia,function = "usb";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ nvidia,lock = <0>;
+ nvidia,open-drain = <1>;
+ };
+ gpio_x6_aud_px6 {
+ nvidia,pins = "gpio_x6_aud_px6";
+ nvidia,function = "spi6";
+ nvidia,pull = <2>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <1>;
+ };
+ gpio_x4_aud_px4 {
+ nvidia,pins = "gpio_x4_aud_px4",
+ "gpio_x7_aud_px7";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ gpio_x5_aud_px5 {
+ nvidia,pins = "gpio_x5_aud_px5";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ gpio_w2_aud_pw2 {
+ nvidia,pins = "gpio_w2_aud_pw2";
+ nvidia,function = "rsvd2";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ gpio_w3_aud_pw3 {
+ nvidia,pins = "gpio_w3_aud_pw3";
+ nvidia,function = "spi6";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ gpio_x1_aud_px1 {
+ nvidia,pins = "gpio_x1_aud_px1";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ gpio_x3_aud_px3 {
+ nvidia,pins = "gpio_x3_aud_px3";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ dap3_fs_pp0 {
+ nvidia,pins = "dap3_fs_pp0";
+ nvidia,function = "i2s2";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ dap3_dout_pp2 {
+ nvidia,pins = "dap3_dout_pp2";
+ nvidia,function = "i2s2";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ pv1 {
+ nvidia,pins = "pv1";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ pbb3 {
+ nvidia,pins = "pbb3",
+ "pbb5",
+ "pbb6",
+ "pbb7";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ pcc1 {
+ nvidia,pins = "pcc1",
+ "pcc2";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ gmi_ad0_pg0 {
+ nvidia,pins = "gmi_ad0_pg0",
+ "gmi_ad1_pg1";
+ nvidia,function = "gmi";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ gmi_ad10_ph2 {
+ nvidia,pins = "gmi_ad10_ph2",
+ "gmi_ad11_ph3",
+ "gmi_ad13_ph5",
+ "gmi_ad8_ph0",
+ "gmi_clk_pk1";
+ nvidia,function = "gmi";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ gmi_ad2_pg2 {
+ nvidia,pins = "gmi_ad2_pg2",
+ "gmi_ad3_pg3";
+ nvidia,function = "gmi";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ gmi_adv_n_pk0 {
+ nvidia,pins = "gmi_adv_n_pk0",
+ "gmi_cs0_n_pj0",
+ "gmi_cs2_n_pk3",
+ "gmi_cs4_n_pk2",
+ "gmi_cs7_n_pi6",
+ "gmi_dqs_p_pj3",
+ "gmi_iordy_pi5",
+ "gmi_wp_n_pc7";
+ nvidia,function = "gmi";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ gmi_cs3_n_pk4 {
+ nvidia,pins = "gmi_cs3_n_pk4";
+ nvidia,function = "gmi";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ clk2_req_pcc5 {
+ nvidia,pins = "clk2_req_pcc5";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ kb_col3_pq3 {
+ nvidia,pins = "kb_col3_pq3",
+ "kb_col6_pq6",
+ "kb_col7_pq7";
+ nvidia,function = "kbc";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ kb_col5_pq5 {
+ nvidia,pins = "kb_col5_pq5";
+ nvidia,function = "kbc";
+ nvidia,pull = <2>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ kb_row3_pr3 {
+ nvidia,pins = "kb_row3_pr3",
+ "kb_row4_pr4",
+ "kb_row6_pr6",
+ "kb_row8_ps0";
+ nvidia,function = "kbc";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ clk3_req_pee1 {
+ nvidia,pins = "clk3_req_pee1";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ pu4 {
+ nvidia,pins = "pu4";
+ nvidia,function = "displayb";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <0>;
+ };
+ pu5 {
+ nvidia,pins = "pu5",
+ "pu6";
+ nvidia,function = "displayb";
+ nvidia,pull = <0>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ hdmi_int_pn7 {
+ nvidia,pins = "hdmi_int_pn7";
+ nvidia,function = "rsvd1";
+ nvidia,pull = <1>;
+ nvidia,tristate = <0>;
+ nvidia,enable-input = <1>;
+ };
+ clk1_req_pee2 {
+ nvidia,pins = "clk1_req_pee2",
+ "usb_vbus_en1_pn5";
+ nvidia,function = "rsvd4";
+ nvidia,pull = <1>;
+ nvidia,tristate = <1>;
+ nvidia,enable-input = <0>;
+ };
+
+ drive_sdio1 {
+ nvidia,pins = "drive_sdio1";
+ nvidia,high-speed-mode = <1>;
+ nvidia,schmitt = <0>;
+ nvidia,low-power-mode = <3>;
+ nvidia,pull-down-strength = <36>;
+ nvidia,pull-up-strength = <20>;
+ nvidia,slew-rate-rising = <2>;
+ nvidia,slew-rate-falling = <2>;
+ };
+ drive_sdio3 {
+ nvidia,pins = "drive_sdio3";
+ nvidia,high-speed-mode = <1>;
+ nvidia,schmitt = <0>;
+ nvidia,low-power-mode = <3>;
+ nvidia,pull-down-strength = <22>;
+ nvidia,pull-up-strength = <36>;
+ nvidia,slew-rate-rising = <0>;
+ nvidia,slew-rate-falling = <0>;
+ };
+ drive_gma {
+ nvidia,pins = "drive_gma";
+ nvidia,high-speed-mode = <1>;
+ nvidia,schmitt = <0>;
+ nvidia,low-power-mode = <3>;
+ nvidia,pull-down-strength = <2>;
+ nvidia,pull-up-strength = <1>;
+ nvidia,slew-rate-rising = <0>;
+ nvidia,slew-rate-falling = <0>;
+ nvidia,drive-type = <1>;
+ };
+ };
+ };
+
serial@70006300 {
status = "okay";
};
+ i2c@7000c000 {
+ status = "okay";
+ clock-frequency = <100000>;
+
+ battery: smart-battery {
+ compatible = "ti,bq20z45", "sbs,sbs-battery";
+ reg = <0xb>;
+ battery-name = "battery";
+ sbs,i2c-retry-count = <2>;
+ sbs,poll-retry-count = <100>;
+ };
+ };
+
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps51632 {
+ compatible = "ti,tps51632";
+ reg = <0x43>;
+ regulator-name = "vdd-cpu";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1520000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ tps65090 {
+ compatible = "ti,tps65090";
+ reg = <0x48>;
+ interrupt-parent = <&gpio>;
+ interrupts = <72 0x04>; /* gpio PJ0 */
+
+ vsys1-supply = <&vdd_ac_bat_reg>;
+ vsys2-supply = <&vdd_ac_bat_reg>;
+ vsys3-supply = <&vdd_ac_bat_reg>;
+ infet1-supply = <&vdd_ac_bat_reg>;
+ infet2-supply = <&vdd_ac_bat_reg>;
+ infet3-supply = <&tps65090_dcdc2_reg>;
+ infet4-supply = <&tps65090_dcdc2_reg>;
+ infet5-supply = <&tps65090_dcdc2_reg>;
+ infet6-supply = <&tps65090_dcdc2_reg>;
+ infet7-supply = <&tps65090_dcdc2_reg>;
+ vsys-l1-supply = <&vdd_ac_bat_reg>;
+ vsys-l2-supply = <&vdd_ac_bat_reg>;
+
+ regulators {
+ tps65090_dcdc1_reg: dcdc1 {
+ regulator-name = "vdd-sys-5v0";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ tps65090_dcdc2_reg: dcdc2 {
+ regulator-name = "vdd-sys-3v3";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ dcdc3 {
+ regulator-name = "vdd-ao";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ fet1 {
+ regulator-name = "vdd-lcd-bl";
+ };
+
+ fet3 {
+ regulator-name = "vdd-modem-3v3";
+ };
+
+ fet4 {
+ regulator-name = "avdd-lcd";
+ };
+
+ fet5 {
+ regulator-name = "vdd-lvds";
+ };
+
+ fet6 {
+ regulator-name = "vdd-sd-slot";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ fet7 {
+ regulator-name = "vdd-com-3v3";
+ };
+
+ ldo1 {
+ regulator-name = "vdd-sby-5v0";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo2 {
+ regulator-name = "vdd-sby-3v3";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+
pmc {
nvidia,invert-interrupt;
};
+ sdhci@78000400 {
+ cd-gpios = <&gpio 170 1>; /* gpio PV2 */
+ bus-width = <4>;
+ status = "okay";
+ };
+
+ sdhci@78000600 {
+ bus-width = <8>;
+ status = "okay";
+ non-removable;
+ };
+
clocks {
compatible = "simple-bus";
#address-cells = <1>;
clock-frequency = <32768>;
};
};
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdd_ac_bat_reg: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "vdd_ac_bat";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ dvdd_ts_reg: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "dvdd_ts";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ gpio = <&gpio 61 0>; /* GPIO PH5 */
+ };
+
+ lcd_bl_en_reg: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "lcd_bl_en";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio 58 0>; /* GPIO PH2 */
+ };
+
+ usb1_vbus_reg: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "usb1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio 108 0>; /* GPIO PN4 */
+ gpio-open-drain;
+ vin-supply = <&tps65090_dcdc1_reg>;
+ };
+
+ usb3_vbus_reg: regulator@4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "usb2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio 86 0>; /* GPIO PK6 */
+ gpio-open-drain;
+ vin-supply = <&tps65090_dcdc1_reg>;
+ };
+
+ vdd_hdmi_reg: regulator@5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ regulator-name = "vdd_hdmi_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio 81 0>; /* GPIO PK1 */
+ vin-supply = <&tps65090_dcdc1_reg>;
+ };
+ };
};
compatible = "nvidia,tegra114";
interrupt-parent = <&gic>;
+ aliases {
+ serial0 = &uarta;
+ serial1 = &uartb;
+ serial2 = &uartc;
+ serial3 = &uartd;
+ };
+
gic: interrupt-controller {
compatible = "arm,cortex-a15-gic";
#interrupt-cells = <3>;
#clock-cells = <1>;
};
+ apbdma: dma {
+ compatible = "nvidia,tegra114-apbdma";
+ reg = <0x6000a000 0x1400>;
+ interrupts = <0 104 0x04
+ 0 105 0x04
+ 0 106 0x04
+ 0 107 0x04
+ 0 108 0x04
+ 0 109 0x04
+ 0 110 0x04
+ 0 111 0x04
+ 0 112 0x04
+ 0 113 0x04
+ 0 114 0x04
+ 0 115 0x04
+ 0 116 0x04
+ 0 117 0x04
+ 0 118 0x04
+ 0 119 0x04
+ 0 128 0x04
+ 0 129 0x04
+ 0 130 0x04
+ 0 131 0x04
+ 0 132 0x04
+ 0 133 0x04
+ 0 134 0x04
+ 0 135 0x04
+ 0 136 0x04
+ 0 137 0x04
+ 0 138 0x04
+ 0 139 0x04
+ 0 140 0x04
+ 0 141 0x04
+ 0 142 0x04
+ 0 143 0x04>;
+ clocks = <&tegra_car 34>;
+ };
+
ahb: ahb {
compatible = "nvidia,tegra114-ahb", "nvidia,tegra30-ahb";
reg = <0x6000c004 0x14c>;
0x70003000 0x40c>; /* Mux registers */
};
- serial@70006000 {
+ /*
+ * There are two serial driver i.e. 8250 based simple serial
+ * driver and APB DMA based serial driver for higher baudrate
+ * and performace. To enable the 8250 based driver, the compatible
+ * is "nvidia,tegra114-uart", "nvidia,tegra20-uart" and to enable
+ * the APB DMA based serial driver, the comptible is
+ * "nvidia,tegra114-hsuart", "nvidia,tegra30-hsuart".
+ */
+ uarta: serial@70006000 {
compatible = "nvidia,tegra114-uart", "nvidia,tegra20-uart";
reg = <0x70006000 0x40>;
reg-shift = <2>;
interrupts = <0 36 0x04>;
+ nvidia,dma-request-selector = <&apbdma 8>;
status = "disabled";
clocks = <&tegra_car 6>;
};
- serial@70006040 {
+ uartb: serial@70006040 {
compatible = "nvidia,tegra114-uart", "nvidia,tegra20-uart";
reg = <0x70006040 0x40>;
reg-shift = <2>;
interrupts = <0 37 0x04>;
+ nvidia,dma-request-selector = <&apbdma 9>;
status = "disabled";
clocks = <&tegra_car 192>;
};
- serial@70006200 {
+ uartc: serial@70006200 {
compatible = "nvidia,tegra114-uart", "nvidia,tegra20-uart";
reg = <0x70006200 0x100>;
reg-shift = <2>;
interrupts = <0 46 0x04>;
+ nvidia,dma-request-selector = <&apbdma 10>;
status = "disabled";
clocks = <&tegra_car 55>;
};
- serial@70006300 {
+ uartd: serial@70006300 {
compatible = "nvidia,tegra114-uart", "nvidia,tegra20-uart";
reg = <0x70006300 0x100>;
reg-shift = <2>;
interrupts = <0 90 0x04>;
+ nvidia,dma-request-selector = <&apbdma 19>;
status = "disabled";
clocks = <&tegra_car 65>;
};
+ pwm: pwm {
+ compatible = "nvidia,tegra114-pwm", "nvidia,tegra20-pwm";
+ reg = <0x7000a000 0x100>;
+ #pwm-cells = <2>;
+ clocks = <&tegra_car 17>;
+ status = "disabled";
+ };
+
+ i2c@7000c000 {
+ compatible = "nvidia,tegra114-i2c";
+ reg = <0x7000c000 0x100>;
+ interrupts = <0 38 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 12>;
+ clock-names = "div-clk";
+ status = "disabled";
+ };
+
+ i2c@7000c400 {
+ compatible = "nvidia,tegra114-i2c";
+ reg = <0x7000c400 0x100>;
+ interrupts = <0 84 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 54>;
+ clock-names = "div-clk";
+ status = "disabled";
+ };
+
+ i2c@7000c500 {
+ compatible = "nvidia,tegra114-i2c";
+ reg = <0x7000c500 0x100>;
+ interrupts = <0 92 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 67>;
+ clock-names = "div-clk";
+ status = "disabled";
+ };
+
+ i2c@7000c700 {
+ compatible = "nvidia,tegra114-i2c";
+ reg = <0x7000c700 0x100>;
+ interrupts = <0 120 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 103>;
+ clock-names = "div-clk";
+ status = "disabled";
+ };
+
+ i2c@7000d000 {
+ compatible = "nvidia,tegra114-i2c";
+ reg = <0x7000d000 0x100>;
+ interrupts = <0 53 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 47>;
+ clock-names = "div-clk";
+ status = "disabled";
+ };
+
+ spi@7000d400 {
+ compatible = "nvidia,tegra114-spi";
+ reg = <0x7000d400 0x200>;
+ interrupts = <0 59 0x04>;
+ nvidia,dma-request-selector = <&apbdma 15>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 41>;
+ clock-names = "spi";
+ status = "disabled";
+ };
+
+ spi@7000d600 {
+ compatible = "nvidia,tegra114-spi";
+ reg = <0x7000d600 0x200>;
+ interrupts = <0 82 0x04>;
+ nvidia,dma-request-selector = <&apbdma 16>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 44>;
+ clock-names = "spi";
+ status = "disabled";
+ };
+
+ spi@7000d800 {
+ compatible = "nvidia,tegra114-spi";
+ reg = <0x7000d800 0x200>;
+ interrupts = <0 83 0x04>;
+ nvidia,dma-request-selector = <&apbdma 17>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 46>;
+ clock-names = "spi";
+ status = "disabled";
+ };
+
+ spi@7000da00 {
+ compatible = "nvidia,tegra114-spi";
+ reg = <0x7000da00 0x200>;
+ interrupts = <0 93 0x04>;
+ nvidia,dma-request-selector = <&apbdma 18>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 68>;
+ clock-names = "spi";
+ status = "disabled";
+ };
+
+ spi@7000dc00 {
+ compatible = "nvidia,tegra114-spi";
+ reg = <0x7000dc00 0x200>;
+ interrupts = <0 94 0x04>;
+ nvidia,dma-request-selector = <&apbdma 27>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 104>;
+ clock-names = "spi";
+ status = "disabled";
+ };
+
+ spi@7000de00 {
+ compatible = "nvidia,tegra114-spi";
+ reg = <0x7000de00 0x200>;
+ interrupts = <0 79 0x04>;
+ nvidia,dma-request-selector = <&apbdma 28>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&tegra_car 105>;
+ clock-names = "spi";
+ status = "disabled";
+ };
+
rtc {
compatible = "nvidia,tegra114-rtc", "nvidia,tegra20-rtc";
reg = <0x7000e000 0x100>;
clocks = <&tegra_car 4>;
};
+ kbc {
+ compatible = "nvidia,tegra114-kbc";
+ reg = <0x7000e200 0x100>;
+ interrupts = <0 85 0x04>;
+ clocks = <&tegra_car 36>;
+ status = "disabled";
+ };
+
pmc {
compatible = "nvidia,tegra114-pmc";
reg = <0x7000e400 0x400>;
nvidia,ahb = <&ahb>;
};
+ sdhci@78000000 {
+ compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+ reg = <0x78000000 0x200>;
+ interrupts = <0 14 0x04>;
+ clocks = <&tegra_car 14>;
+ status = "disable";
+ };
+
+ sdhci@78000200 {
+ compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+ reg = <0x78000200 0x200>;
+ interrupts = <0 15 0x04>;
+ clocks = <&tegra_car 9>;
+ status = "disable";
+ };
+
+ sdhci@78000400 {
+ compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+ reg = <0x78000400 0x200>;
+ interrupts = <0 19 0x04>;
+ clocks = <&tegra_car 69>;
+ status = "disable";
+ };
+
+ sdhci@78000600 {
+ compatible = "nvidia,tegra114-sdhci", "nvidia,tegra30-sdhci";
+ reg = <0x78000600 0x200>;
+ interrupts = <0 31 0x04>;
+ clocks = <&tegra_car 15>;
+ status = "disable";
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
};
};
+ pmc {
+ nvidia,suspend-mode = <2>;
+ nvidia,cpu-pwr-good-time = <5000>;
+ nvidia,cpu-pwr-off-time = <5000>;
+ nvidia,core-pwr-good-time = <3845 3845>;
+ nvidia,core-pwr-off-time = <3875>;
+ nvidia,sys-clock-req-active-high;
+ };
+
memory-controller@7000f400 {
emc-table@83250 {
reg = <83250>;
"Mic", "MIC1";
nvidia,ac97-controller = <&ac97>;
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
regulators {
pmc {
nvidia,invert-interrupt;
+ nvidia,suspend-mode = <2>;
+ nvidia,cpu-pwr-good-time = <5000>;
+ nvidia,cpu-pwr-off-time = <5000>;
+ nvidia,core-pwr-good-time = <3845 3845>;
+ nvidia,core-pwr-off-time = <3875>;
+ nvidia,sys-clock-req-active-high;
};
usb@c5000000 {
};
};
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "Power";
+ gpios = <&gpio 170 1>; /* gpio PV2, active low */
+ linux,code = <116>; /* KEY_POWER */
+ gpio-key,wakeup;
+ };
+ };
+
kbc {
status = "okay";
nvidia,debounce-delay-ms = <2>;
nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
};
model = "Avionic Design Medcom-Wide board";
compatible = "ad,medcom-wide", "ad,tamonten", "nvidia,tegra20";
+ pwm {
+ status = "okay";
+ };
+
i2c@7000c000 {
wm8903: wm8903@1a {
compatible = "wlf,wm8903";
nvidia,spkr-en-gpios = <&wm8903 2 0>;
nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
};
pmc {
nvidia,invert-interrupt;
+ nvidia,suspend-mode = <2>;
+ nvidia,cpu-pwr-good-time = <2000>;
+ nvidia,cpu-pwr-off-time = <0>;
+ nvidia,core-pwr-good-time = <3845 3845>;
+ nvidia,core-pwr-off-time = <0>;
+ nvidia,sys-clock-req-active-high;
};
usb@c5000000 {
sdhci@c8000600 {
status = "okay";
bus-width = <8>;
+ non-removable;
};
clocks {
nvidia,audio-codec = <&alc5632>;
nvidia,i2s-controller = <&tegra_i2s1>;
nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
};
nvidia,spkr-en-gpios = <&wm8903 2 0>;
nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
};
pmc {
nvidia,invert-interrupt;
+ nvidia,suspend-mode = <2>;
+ nvidia,cpu-pwr-good-time = <5000>;
+ nvidia,cpu-pwr-off-time = <5000>;
+ nvidia,core-pwr-good-time = <3845 3845>;
+ nvidia,core-pwr-off-time = <3875>;
+ nvidia,sys-clock-req-active-high;
};
memory-controller@7000f400 {
status = "okay";
power-gpios = <&gpio 86 0>; /* gpio PK6 */
bus-width = <4>;
+ keep-power-in-suspend;
};
sdhci@c8000400 {
sdhci@c8000600 {
status = "okay";
bus-width = <8>;
+ non-removable;
};
clocks {
nvidia,spkr-en-gpios = <&wm8903 2 0>;
nvidia,hp-det-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
};
pmc {
nvidia,invert-interrupt;
+ nvidia,suspend-mode = <2>;
+ nvidia,cpu-pwr-good-time = <5000>;
+ nvidia,cpu-pwr-off-time = <5000>;
+ nvidia,core-pwr-good-time = <3845 3845>;
+ nvidia,core-pwr-off-time = <3875>;
+ nvidia,sys-clock-req-active-high;
};
usb@c5008000 {
nvidia,spkr-en-gpios = <&wm8903 2 0>;
nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
};
};
};
+ pmc {
+ nvidia,suspend-mode = <2>;
+ nvidia,cpu-pwr-good-time = <5000>;
+ nvidia,cpu-pwr-off-time = <5000>;
+ nvidia,core-pwr-good-time = <3845 3845>;
+ nvidia,core-pwr-off-time = <3875>;
+ nvidia,sys-clock-req-active-high;
+ };
+
usb@c5000000 {
status = "okay";
nvidia,vbus-gpio = <&gpio 170 0>; /* gpio PV2 */
};
};
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "Power";
+ gpios = <&gpio 190 1>; /* gpio PX6, active low */
+ linux,code = <116>; /* KEY_POWER */
+ gpio-key,wakeup;
+ };
+ };
+
poweroff {
compatible = "gpio-poweroff";
gpios = <&gpio 191 1>; /* gpio PX7, active low */
compatible = "nvidia,tegra-audio-trimslice";
nvidia,i2s-controller = <&tegra_i2s1>;
nvidia,audio-codec = <&codec>;
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
};
pmc {
nvidia,invert-interrupt;
+ nvidia,suspend-mode = <2>;
+ nvidia,cpu-pwr-good-time = <2000>;
+ nvidia,cpu-pwr-off-time = <100>;
+ nvidia,core-pwr-good-time = <3845 3845>;
+ nvidia,core-pwr-off-time = <458>;
+ nvidia,sys-clock-req-active-high;
};
usb@c5000000 {
status = "okay";
power-gpios = <&gpio 86 0>; /* gpio PK6 */
bus-width = <4>;
+ keep-power-in-suspend;
};
sdhci@c8000400 {
sdhci@c8000600 {
status = "okay";
bus-width = <8>;
+ non-removable;
};
clocks {
};
};
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "Power";
+ gpios = <&gpio 170 1>; /* gpio PV2, active low */
+ linux,code = <116>; /* KEY_POWER */
+ gpio-key,wakeup;
+ };
+ };
+
regulators {
compatible = "simple-bus";
#address-cells = <1>;
nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
nvidia,int-mic-en-gpios = <&gpio 184 0>; /* gpio PX0 */
nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
};
pmc {
nvidia,invert-interrupt;
+ nvidia,suspend-mode = <2>;
+ nvidia,cpu-pwr-good-time = <2000>;
+ nvidia,cpu-pwr-off-time = <1000>;
+ nvidia,core-pwr-good-time = <0 3845>;
+ nvidia,core-pwr-off-time = <93727>;
+ nvidia,core-power-req-active-high;
+ nvidia,sys-clock-req-active-high;
+ nvidia,combined-power-req;
};
usb@c5000000 {
sdhci@c8000600 {
status = "okay";
bus-width = <8>;
+ non-removable;
};
clocks {
nvidia,repeat-delay-ms = <160>;
nvidia,kbc-row-pins = <0 1 2>;
nvidia,kbc-col-pins = <16 17>;
+ nvidia,wakeup-source;
linux,keymap = <0x00000074 /* KEY_POWER */
0x01000066 /* KEY_HOME */
0x0101009E /* KEY_BACK */
nvidia,i2s-controller = <&tegra_i2s1>;
nvidia,audio-codec = <&codec>;
+
+ clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 94>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
};
compatible = "nvidia,tegra20-das";
reg = <0x70000c00 0x80>;
};
-
+
tegra_ac97: ac97 {
compatible = "nvidia,tegra20-ac97";
reg = <0x70002000 0x200>;
reg = <0x7000a000 0x100>;
#pwm-cells = <2>;
clocks = <&tegra_car 17>;
+ status = "disabled";
};
rtc {
#size-cells = <0>;
};
- phy1: usb-phy@c5000400 {
- compatible = "nvidia,tegra20-usb-phy";
- reg = <0xc5000400 0x3c00>;
- phy_type = "utmi";
- nvidia,has-legacy-mode;
- clocks = <&tegra_car 22>, <&tegra_car 127>;
- clock-names = "phy", "pll_u";
- };
-
- phy2: usb-phy@c5004400 {
- compatible = "nvidia,tegra20-usb-phy";
- reg = <0xc5004400 0x3c00>;
- phy_type = "ulpi";
- clocks = <&tegra_car 94>, <&tegra_car 127>;
- clock-names = "phy", "pll_u";
- };
-
- phy3: usb-phy@c5008400 {
- compatible = "nvidia,tegra20-usb-phy";
- reg = <0xc5008400 0x3C00>;
- phy_type = "utmi";
- clocks = <&tegra_car 22>, <&tegra_car 127>;
- clock-names = "phy", "pll_u";
- };
-
usb@c5000000 {
compatible = "nvidia,tegra20-ehci", "usb-ehci";
reg = <0xc5000000 0x4000>;
status = "disabled";
};
+ phy1: usb-phy@c5000400 {
+ compatible = "nvidia,tegra20-usb-phy";
+ reg = <0xc5000400 0x3c00>;
+ phy_type = "utmi";
+ nvidia,has-legacy-mode;
+ clocks = <&tegra_car 22>, <&tegra_car 127>;
+ clock-names = "phy", "pll_u";
+ };
+
usb@c5004000 {
compatible = "nvidia,tegra20-ehci", "usb-ehci";
reg = <0xc5004000 0x4000>;
status = "disabled";
};
+ phy2: usb-phy@c5004400 {
+ compatible = "nvidia,tegra20-usb-phy";
+ reg = <0xc5004400 0x3c00>;
+ phy_type = "ulpi";
+ clocks = <&tegra_car 93>, <&tegra_car 127>;
+ clock-names = "phy", "pll_u";
+ };
+
usb@c5008000 {
compatible = "nvidia,tegra20-ehci", "usb-ehci";
reg = <0xc5008000 0x4000>;
status = "disabled";
};
+ phy3: usb-phy@c5008400 {
+ compatible = "nvidia,tegra20-usb-phy";
+ reg = <0xc5008400 0x3c00>;
+ phy_type = "utmi";
+ clocks = <&tegra_car 22>, <&tegra_car 127>;
+ clock-names = "phy", "pll_u";
+ };
+
sdhci@c8000000 {
compatible = "nvidia,tegra20-sdhci";
reg = <0xc8000000 0x200>;
pmc {
status = "okay";
nvidia,invert-interrupt;
+ nvidia,suspend-mode = <2>;
+ nvidia,cpu-pwr-good-time = <2000>;
+ nvidia,cpu-pwr-off-time = <200>;
+ nvidia,core-pwr-good-time = <3845 3845>;
+ nvidia,core-pwr-off-time = <0>;
+ nvidia,core-power-req-active-high;
+ nvidia,sys-clock-req-active-high;
};
sdhci@78000000 {
sdhci@78000600 {
status = "okay";
bus-width = <8>;
+ non-removable;
};
clocks {
status = "okay";
power-gpios = <&gpio 28 0>; /* gpio PD4 */
bus-width = <4>;
+ keep-power-in-suspend;
};
};
status = "okay";
power-gpios = <&gpio 27 0>; /* gpio PD3 */
bus-width = <4>;
+ keep-power-in-suspend;
};
};
pmc {
status = "okay";
nvidia,invert-interrupt;
+ nvidia,suspend-mode = <2>;
+ nvidia,cpu-pwr-good-time = <2000>;
+ nvidia,cpu-pwr-off-time = <200>;
+ nvidia,core-pwr-good-time = <3845 3845>;
+ nvidia,core-pwr-off-time = <0>;
+ nvidia,core-power-req-active-high;
+ nvidia,sys-clock-req-active-high;
};
sdhci@78000000 {
sdhci@78000600 {
status = "okay";
bus-width = <8>;
+ non-removable;
};
clocks {
nvidia,spkr-en-gpios = <&wm8903 2 0>;
nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
+
+ clocks = <&tegra_car 184>, <&tegra_car 185>, <&tegra_car 120>;
+ clock-names = "pll_a", "pll_a_out0", "mclk";
};
};
reg = <0x7000a000 0x100>;
#pwm-cells = <2>;
clocks = <&tegra_car 17>;
+ status = "disabled";
};
rtc {
compatible = "ti,twl4030-wdt";
};
+ vcc: regulator-vdd1 {
+ compatible = "ti,twl4030-vdd1";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1450000>;
+ };
+
vdac: regulator-vdac {
compatible = "ti,twl4030-vdac";
regulator-min-microvolt = <1800000>;
#interrupt-cells = <1>;
};
- twl4030-usb {
+ usb2_phy: twl4030-usb {
compatible = "ti,twl4030-usb";
interrupts = <10>, <4>;
usb1v5-supply = <&vusb1v5>;
usb3v1-supply = <&vusb3v1>;
usb_mode = <1>;
};
+
+ twl_pwm: pwm {
+ compatible = "ti,twl4030-pwm";
+ #pwm-cells = <2>;
+ };
+
+ twl_pwmled: pwmled {
+ compatible = "ti,twl4030-pwmled";
+ #pwm-cells = <2>;
+ };
};
compatible = "ti,twl6030-usb";
interrupts = <4>, <10>;
};
+
+ twl_pwm: pwm {
+ /* provides two PWMs (id 0, 1 for PWM1 and PWM2) */
+ compatible = "ti,twl6030-pwm";
+ #pwm-cells = <2>;
+ };
+
+ twl_pwmled: pwmled {
+ /* provides one PWM (id 0 for Charging indicator LED) */
+ compatible = "ti,twl6030-pwmled";
+ #pwm-cells = <2>;
+ };
};
OF_DEV_AUXDATA("ti,davinci-i2c", 0x01c22000, "i2c_davinci.1", NULL),
OF_DEV_AUXDATA("ti,davinci-wdt", 0x01c21000, "watchdog", NULL),
OF_DEV_AUXDATA("ti,da830-mmc", 0x01c40000, "da830-mmc.0", NULL),
+ OF_DEV_AUXDATA("ti,da850-ehrpwm", 0x01f00000, "ehrpwm", NULL),
+ OF_DEV_AUXDATA("ti,da850-ehrpwm", 0x01f02000, "ehrpwm", NULL),
+ OF_DEV_AUXDATA("ti,da850-ecap", 0x01f06000, "ecap", NULL),
+ OF_DEV_AUXDATA("ti,da850-ecap", 0x01f07000, "ecap", NULL),
+ OF_DEV_AUXDATA("ti,da850-ecap", 0x01f08000, "ecap", NULL),
+ OF_DEV_AUXDATA("ti,da830-spi", 0x01f0e000, "spi_davinci.1", NULL),
{}
};
},
};
-#ifdef CONFIG_ARCH_EXYNOS5
-static struct map_desc exynos5440_iodesc[] __initdata = {
- {
- .virtual = (unsigned long)S5P_VA_CHIPID,
- .pfn = __phys_to_pfn(EXYNOS5440_PA_CHIPID),
- .length = SZ_4K,
- .type = MT_DEVICE,
- },
-};
-#endif
-
static struct map_desc exynos4_iodesc[] __initdata = {
{
.virtual = (unsigned long)S3C_VA_SYS,
exynos_pm_late_initcall();
}
+#ifdef CONFIG_OF
+int __init exynos_fdt_map_chipid(unsigned long node, const char *uname,
+ int depth, void *data)
+{
+ struct map_desc iodesc;
+ __be32 *reg;
+ unsigned long len;
+
+ if (!of_flat_dt_is_compatible(node, "samsung,exynos4210-chipid") &&
+ !of_flat_dt_is_compatible(node, "samsung,exynos5440-clock"))
+ return 0;
+
+ reg = of_get_flat_dt_prop(node, "reg", &len);
+ if (reg == NULL || len != (sizeof(unsigned long) * 2))
+ return 0;
+
+ iodesc.pfn = __phys_to_pfn(be32_to_cpu(reg[0]));
+ iodesc.length = be32_to_cpu(reg[1]) - 1;
+ iodesc.virtual = (unsigned long)S5P_VA_CHIPID;
+ iodesc.type = MT_DEVICE;
+ iotable_init(&iodesc, 1);
+ return 1;
+}
+#endif
+
/*
* exynos_map_io
*
void __init exynos_init_io(struct map_desc *mach_desc, int size)
{
- struct map_desc *iodesc = exynos_iodesc;
- int iodesc_sz = ARRAY_SIZE(exynos_iodesc);
-#if defined(CONFIG_OF) && defined(CONFIG_ARCH_EXYNOS5)
- unsigned long root = of_get_flat_dt_root();
-
- /* initialize the io descriptors we need for initialization */
- if (of_flat_dt_is_compatible(root, "samsung,exynos5440")) {
- iodesc = exynos5440_iodesc;
- iodesc_sz = ARRAY_SIZE(exynos5440_iodesc);
- }
+#ifdef CONFIG_OF
+ if (initial_boot_params)
+ of_scan_flat_dt(exynos_fdt_map_chipid, NULL);
+ else
#endif
-
- iotable_init(iodesc, iodesc_sz);
+ iotable_init(exynos_iodesc, ARRAY_SIZE(exynos_iodesc));
if (mach_desc)
iotable_init(mach_desc, size);
#define EXYNOS4_PA_ONENAND_DMA 0x0C600000
#define EXYNOS_PA_CHIPID 0x10000000
-#define EXYNOS5440_PA_CHIPID 0x00160000
#define EXYNOS4_PA_SYSCON 0x10010000
#define EXYNOS5_PA_SYSCON 0x10050100
#include <linux/irqchip.h>
#include <linux/irqchip/mxs.h>
#include <linux/micrel_phy.h>
-#include <linux/mxsfb.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>
#include <linux/phy.h>
__raw_writel(mask, reg + MXS_TOG_ADDR);
}
-static struct fb_videomode mx23evk_video_modes[] = {
- {
- .name = "Samsung-LMS430HF02",
- .refresh = 60,
- .xres = 480,
- .yres = 272,
- .pixclock = 108096, /* picosecond (9.2 MHz) */
- .left_margin = 15,
- .right_margin = 8,
- .upper_margin = 12,
- .lower_margin = 4,
- .hsync_len = 1,
- .vsync_len = 1,
- },
-};
-
-static struct fb_videomode mx28evk_video_modes[] = {
- {
- .name = "Seiko-43WVF1G",
- .refresh = 60,
- .xres = 800,
- .yres = 480,
- .pixclock = 29851, /* picosecond (33.5 MHz) */
- .left_margin = 89,
- .right_margin = 164,
- .upper_margin = 23,
- .lower_margin = 10,
- .hsync_len = 10,
- .vsync_len = 10,
- },
-};
-
-static struct fb_videomode m28evk_video_modes[] = {
- {
- .name = "Ampire AM-800480R2TMQW-T01H",
- .refresh = 60,
- .xres = 800,
- .yres = 480,
- .pixclock = 30066, /* picosecond (33.26 MHz) */
- .left_margin = 0,
- .right_margin = 256,
- .upper_margin = 0,
- .lower_margin = 45,
- .hsync_len = 1,
- .vsync_len = 1,
- },
-};
-
-static struct fb_videomode apx4devkit_video_modes[] = {
- {
- .name = "HannStar PJ70112A",
- .refresh = 60,
- .xres = 800,
- .yres = 480,
- .pixclock = 33333, /* picosecond (30.00 MHz) */
- .left_margin = 88,
- .right_margin = 40,
- .upper_margin = 32,
- .lower_margin = 13,
- .hsync_len = 48,
- .vsync_len = 3,
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
- },
-};
-
-static struct fb_videomode apf28dev_video_modes[] = {
- {
- .name = "LW700",
- .refresh = 60,
- .xres = 800,
- .yres = 480,
- .pixclock = 30303, /* picosecond */
- .left_margin = 96,
- .right_margin = 96, /* at least 3 & 1 */
- .upper_margin = 0x14,
- .lower_margin = 0x15,
- .hsync_len = 64,
- .vsync_len = 4,
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
- },
-};
-
-static struct fb_videomode cfa10049_video_modes[] = {
- {
- .name = "Himax HX8357-B",
- .refresh = 60,
- .xres = 320,
- .yres = 480,
- .pixclock = 108506, /* picosecond (9.216 MHz) */
- .left_margin = 2,
- .right_margin = 2,
- .upper_margin = 2,
- .lower_margin = 2,
- .hsync_len = 15,
- .vsync_len = 15,
- },
-};
-
-static struct mxsfb_platform_data mxsfb_pdata __initdata;
-
/*
* MX28EVK_FLEXCAN_SWITCH is shared between both flexcan controllers
*/
static struct flexcan_platform_data flexcan_pdata[2];
static struct of_dev_auxdata mxs_auxdata_lookup[] __initdata = {
- OF_DEV_AUXDATA("fsl,imx23-lcdif", 0x80030000, NULL, &mxsfb_pdata),
- OF_DEV_AUXDATA("fsl,imx28-lcdif", 0x80030000, NULL, &mxsfb_pdata),
OF_DEV_AUXDATA("fsl,imx28-flexcan", 0x80032000, NULL, &flexcan_pdata[0]),
OF_DEV_AUXDATA("fsl,imx28-flexcan", 0x80034000, NULL, &flexcan_pdata[1]),
{ /* sentinel */ }
}
}
-static void __init imx23_evk_init(void)
-{
- mxsfb_pdata.mode_list = mx23evk_video_modes;
- mxsfb_pdata.mode_count = ARRAY_SIZE(mx23evk_video_modes);
- mxsfb_pdata.default_bpp = 32;
- mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
- mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
- MXSFB_SYNC_DOTCLK_FAILING_ACT;
-}
-
static inline void enable_clk_enet_out(void)
{
struct clk *clk = clk_get_sys("enet_out", NULL);
static void __init imx28_evk_init(void)
{
- enable_clk_enet_out();
update_fec_mac_prop(OUI_FSL);
- mxsfb_pdata.mode_list = mx28evk_video_modes;
- mxsfb_pdata.mode_count = ARRAY_SIZE(mx28evk_video_modes);
- mxsfb_pdata.default_bpp = 32;
- mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
- mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
- MXSFB_SYNC_DOTCLK_FAILING_ACT;
-
mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0);
}
}
}
-static void __init m28evk_init(void)
-{
- mxsfb_pdata.mode_list = m28evk_video_modes;
- mxsfb_pdata.mode_count = ARRAY_SIZE(m28evk_video_modes);
- mxsfb_pdata.default_bpp = 16;
- mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
- mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT;
-}
-
-static void __init sc_sps1_init(void)
-{
- enable_clk_enet_out();
-}
-
static int apx4devkit_phy_fixup(struct phy_device *phy)
{
phy->dev_flags |= MICREL_PHY_50MHZ_CLK;
if (IS_BUILTIN(CONFIG_PHYLIB))
phy_register_fixup_for_uid(PHY_ID_KSZ8051, MICREL_PHY_ID_MASK,
apx4devkit_phy_fixup);
-
- mxsfb_pdata.mode_list = apx4devkit_video_modes;
- mxsfb_pdata.mode_count = ARRAY_SIZE(apx4devkit_video_modes);
- mxsfb_pdata.default_bpp = 32;
- mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT;
- mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
- MXSFB_SYNC_DOTCLK_FAILING_ACT;
}
#define ENET0_MDC__GPIO_4_0 MXS_GPIO_NR(4, 0)
static void __init cfa10049_init(void)
{
- enable_clk_enet_out();
update_fec_mac_prop(OUI_CRYSTALFONTZ);
-
- mxsfb_pdata.mode_list = cfa10049_video_modes;
- mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes);
- mxsfb_pdata.default_bpp = 32;
- mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT;
- mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT;
}
static void __init cfa10037_init(void)
{
- enable_clk_enet_out();
update_fec_mac_prop(OUI_CRYSTALFONTZ);
}
-static void __init apf28_init(void)
-{
- enable_clk_enet_out();
-
- mxsfb_pdata.mode_list = apf28dev_video_modes;
- mxsfb_pdata.mode_count = ARRAY_SIZE(apf28dev_video_modes);
- mxsfb_pdata.default_bpp = 16;
- mxsfb_pdata.ld_intf_width = STMLCDIF_16BIT;
- mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT |
- MXSFB_SYNC_DOTCLK_FAILING_ACT;
-}
-
static void __init mxs_machine_init(void)
{
if (of_machine_is_compatible("fsl,imx28-evk"))
imx28_evk_init();
- else if (of_machine_is_compatible("fsl,imx23-evk"))
- imx23_evk_init();
- else if (of_machine_is_compatible("denx,m28evk"))
- m28evk_init();
else if (of_machine_is_compatible("bluegiga,apx4devkit"))
apx4devkit_init();
else if (of_machine_is_compatible("crystalfontz,cfa10037"))
cfa10037_init();
else if (of_machine_is_compatible("crystalfontz,cfa10049"))
cfa10049_init();
- else if (of_machine_is_compatible("armadeus,imx28-apf28"))
- apf28_init();
- else if (of_machine_is_compatible("schulercontrol,imx28-sps1"))
- sc_sps1_init();
of_platform_populate(NULL, of_default_bus_match_table,
mxs_auxdata_lookup, NULL);
static const char *omap3_gp_boards_compat[] __initdata = {
"ti,omap3-beagle",
+ "timll,omap3-devkit8000",
NULL,
};
#include <linux/slab.h>
#include <linux/bootmem.h>
#include <linux/cpu.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
#include <asm/system_misc.h>
return 0;
}
+/**
+ * of_dev_hwmod_lookup - look up needed hwmod from dt blob
+ * @np: struct device_node *
+ * @oh: struct omap_hwmod *
+ *
+ * Parse the dt blob and find out needed hwmod. Recursive function is
+ * implemented to take care hierarchical dt blob parsing.
+ * Return: The device node on success or NULL on failure.
+ */
+static struct device_node *of_dev_hwmod_lookup(struct device_node *np,
+ struct omap_hwmod *oh)
+{
+ struct device_node *np0 = NULL, *np1 = NULL;
+ const char *p;
+
+ for_each_child_of_node(np, np0) {
+ if (of_find_property(np0, "ti,hwmods", NULL)) {
+ p = of_get_property(np0, "ti,hwmods", NULL);
+ if (!strcmp(p, oh->name))
+ return np0;
+ np1 = of_dev_hwmod_lookup(np0, oh);
+ if (np1)
+ return np1;
+ }
+ }
+ return NULL;
+}
+
/**
* _init_mpu_rt_base - populate the virtual address for a hwmod
* @oh: struct omap_hwmod * to locate the virtual address
static void __init _init_mpu_rt_base(struct omap_hwmod *oh, void *data)
{
struct omap_hwmod_addr_space *mem;
- void __iomem *va_start;
+ void __iomem *va_start = NULL;
+ struct device_node *np;
if (!oh)
return;
if (!mem) {
pr_debug("omap_hwmod: %s: no MPU register target found\n",
oh->name);
- return;
+
+ /* Extract the IO space from device tree blob */
+ if (!of_have_populated_dt())
+ return;
+
+ np = of_dev_hwmod_lookup(of_find_node_by_name(NULL, "ocp"), oh);
+ if (np)
+ va_start = of_iomap(np, 0);
+ } else {
+ va_start = ioremap(mem->pa_start, mem->pa_end - mem->pa_start);
}
- va_start = ioremap(mem->pa_start, mem->pa_end - mem->pa_start);
if (!va_start) {
pr_err("omap_hwmod: %s: Could not ioremap\n", oh->name);
return;
if (oh->_state != _HWMOD_STATE_REGISTERED)
return 0;
- _init_mpu_rt_base(oh, NULL);
+ if (oh->class->sysc)
+ _init_mpu_rt_base(oh, NULL);
r = _init_clocks(oh, NULL);
if (r < 0) {
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
+#include <linux/of.h>
+
#include <asm/pmu.h>
#include "soc.h"
unsigned oh_num;
char **oh_names;
+ /* XXX Remove this check when the CTI driver is available */
+ if (cpu_is_omap443x()) {
+ pr_info("ARM PMU: not yet supported on OMAP4430 due to missing CTI driver\n");
+ return 0;
+ }
+
+ if (of_have_populated_dt())
+ return 0;
+
/*
* To create an ARM-PMU device the following HWMODs
* are required for the various OMAP2+ devices.
if (cpu_is_omap443x()) {
oh_num = ARRAY_SIZE(omap4430_pmu_oh_names);
oh_names = omap4430_pmu_oh_names;
- /* XXX Remove the next two lines when CTI driver available */
- pr_info("ARM PMU: not yet supported on OMAP4430 due to missing CTI driver\n");
- return 0;
} else if (cpu_is_omap34xx() || cpu_is_omap44xx()) {
oh_num = ARRAY_SIZE(omap3_pmu_oh_names);
oh_names = omap3_pmu_oh_names;
};
static struct of_device_id omap_timer_match[] __initdata = {
- { .compatible = "ti,omap2-timer", },
+ { .compatible = "ti,omap2420-timer", },
+ { .compatible = "ti,omap3430-timer", },
+ { .compatible = "ti,omap4430-timer", },
+ { .compatible = "ti,omap5430-timer", },
+ { .compatible = "ti,am335x-timer", },
+ { .compatible = "ti,am335x-timer-1ms", },
{ }
};
static LIST_HEAD(omap_timer_list);
static DEFINE_SPINLOCK(dm_timer_lock);
+enum {
+ REQUEST_ANY = 0,
+ REQUEST_BY_ID,
+ REQUEST_BY_CAP,
+ REQUEST_BY_NODE,
+};
+
/**
* omap_dm_timer_read_reg - read timer registers in posted and non-posted mode
* @timer: timer pointer over which read operation to perform
return 0;
}
-struct omap_dm_timer *omap_dm_timer_request(void)
+static struct omap_dm_timer *_omap_dm_timer_request(int req_type, void *data)
{
struct omap_dm_timer *timer = NULL, *t;
+ struct device_node *np = NULL;
unsigned long flags;
- int ret = 0;
+ u32 cap = 0;
+ int id = 0;
+
+ switch (req_type) {
+ case REQUEST_BY_ID:
+ id = *(int *)data;
+ break;
+ case REQUEST_BY_CAP:
+ cap = *(u32 *)data;
+ break;
+ case REQUEST_BY_NODE:
+ np = (struct device_node *)data;
+ break;
+ default:
+ /* REQUEST_ANY */
+ break;
+ }
spin_lock_irqsave(&dm_timer_lock, flags);
list_for_each_entry(t, &omap_timer_list, node) {
if (t->reserved)
continue;
- timer = t;
- timer->reserved = 1;
- break;
+ switch (req_type) {
+ case REQUEST_BY_ID:
+ if (id == t->pdev->id) {
+ timer = t;
+ timer->reserved = 1;
+ goto found;
+ }
+ break;
+ case REQUEST_BY_CAP:
+ if (cap == (t->capability & cap)) {
+ /*
+ * If timer is not NULL, we have already found
+ * one timer but it was not an exact match
+ * because it had more capabilites that what
+ * was required. Therefore, unreserve the last
+ * timer found and see if this one is a better
+ * match.
+ */
+ if (timer)
+ timer->reserved = 0;
+ timer = t;
+ timer->reserved = 1;
+
+ /* Exit loop early if we find an exact match */
+ if (t->capability == cap)
+ goto found;
+ }
+ break;
+ case REQUEST_BY_NODE:
+ if (np == t->pdev->dev.of_node) {
+ timer = t;
+ timer->reserved = 1;
+ goto found;
+ }
+ break;
+ default:
+ /* REQUEST_ANY */
+ timer = t;
+ timer->reserved = 1;
+ goto found;
+ }
}
+found:
spin_unlock_irqrestore(&dm_timer_lock, flags);
- if (timer) {
- ret = omap_dm_timer_prepare(timer);
- if (ret) {
- timer->reserved = 0;
- timer = NULL;
- }
+ if (timer && omap_dm_timer_prepare(timer)) {
+ timer->reserved = 0;
+ timer = NULL;
}
if (!timer)
return timer;
}
+
+struct omap_dm_timer *omap_dm_timer_request(void)
+{
+ return _omap_dm_timer_request(REQUEST_ANY, NULL);
+}
EXPORT_SYMBOL_GPL(omap_dm_timer_request);
struct omap_dm_timer *omap_dm_timer_request_specific(int id)
{
- struct omap_dm_timer *timer = NULL, *t;
- unsigned long flags;
- int ret = 0;
-
/* Requesting timer by ID is not supported when device tree is used */
if (of_have_populated_dt()) {
- pr_warn("%s: Please use omap_dm_timer_request_by_cap()\n",
+ pr_warn("%s: Please use omap_dm_timer_request_by_cap/node()\n",
__func__);
return NULL;
}
- spin_lock_irqsave(&dm_timer_lock, flags);
- list_for_each_entry(t, &omap_timer_list, node) {
- if (t->pdev->id == id && !t->reserved) {
- timer = t;
- timer->reserved = 1;
- break;
- }
- }
- spin_unlock_irqrestore(&dm_timer_lock, flags);
-
- if (timer) {
- ret = omap_dm_timer_prepare(timer);
- if (ret) {
- timer->reserved = 0;
- timer = NULL;
- }
- }
-
- if (!timer)
- pr_debug("%s: timer%d request failed!\n", __func__, id);
-
- return timer;
+ return _omap_dm_timer_request(REQUEST_BY_ID, &id);
}
EXPORT_SYMBOL_GPL(omap_dm_timer_request_specific);
*/
struct omap_dm_timer *omap_dm_timer_request_by_cap(u32 cap)
{
- struct omap_dm_timer *timer = NULL, *t;
- unsigned long flags;
+ return _omap_dm_timer_request(REQUEST_BY_CAP, &cap);
+}
+EXPORT_SYMBOL_GPL(omap_dm_timer_request_by_cap);
- if (!cap)
+/**
+ * omap_dm_timer_request_by_node - Request a timer by device-tree node
+ * @np: Pointer to device-tree timer node
+ *
+ * Request a timer based upon a device node pointer. Returns pointer to
+ * timer handle on success and a NULL pointer on failure.
+ */
+struct omap_dm_timer *omap_dm_timer_request_by_node(struct device_node *np)
+{
+ if (!np)
return NULL;
- spin_lock_irqsave(&dm_timer_lock, flags);
- list_for_each_entry(t, &omap_timer_list, node) {
- if ((!t->reserved) && ((t->capability & cap) == cap)) {
- /*
- * If timer is not NULL, we have already found one timer
- * but it was not an exact match because it had more
- * capabilites that what was required. Therefore,
- * unreserve the last timer found and see if this one
- * is a better match.
- */
- if (timer)
- timer->reserved = 0;
-
- timer = t;
- timer->reserved = 1;
-
- /* Exit loop early if we find an exact match */
- if (t->capability == cap)
- break;
- }
- }
- spin_unlock_irqrestore(&dm_timer_lock, flags);
-
- if (timer && omap_dm_timer_prepare(timer)) {
- timer->reserved = 0;
- timer = NULL;
- }
-
- if (!timer)
- pr_debug("%s: timer request failed!\n", __func__);
-
- return timer;
+ return _omap_dm_timer_request(REQUEST_BY_NODE, np);
}
-EXPORT_SYMBOL_GPL(omap_dm_timer_request_by_cap);
+EXPORT_SYMBOL_GPL(omap_dm_timer_request_by_node);
int omap_dm_timer_free(struct omap_dm_timer *timer)
{
void omap_dm_timer_enable(struct omap_dm_timer *timer)
{
+ int c;
+
pm_runtime_get_sync(&timer->pdev->dev);
+
+ if (!(timer->capability & OMAP_TIMER_ALWON)) {
+ if (timer->get_context_loss_count) {
+ c = timer->get_context_loss_count(&timer->pdev->dev);
+ if (c != timer->ctx_loss_count) {
+ omap_timer_restore_context(timer);
+ timer->ctx_loss_count = c;
+ }
+ } else {
+ omap_timer_restore_context(timer);
+ }
+ }
}
EXPORT_SYMBOL_GPL(omap_dm_timer_enable);
omap_dm_timer_enable(timer);
- if (!(timer->capability & OMAP_TIMER_ALWON)) {
- if (timer->get_context_loss_count &&
- timer->get_context_loss_count(&timer->pdev->dev) !=
- timer->ctx_loss_count)
- omap_timer_restore_context(timer);
- }
-
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
if (!(l & OMAP_TIMER_CTRL_ST)) {
l |= OMAP_TIMER_CTRL_ST;
__omap_dm_timer_stop(timer, timer->posted, rate);
- if (!(timer->capability & OMAP_TIMER_ALWON)) {
- if (timer->get_context_loss_count)
- timer->ctx_loss_count =
- timer->get_context_loss_count(&timer->pdev->dev);
- }
-
/*
* Since the register values are computed and written within
* __omap_dm_timer_stop, we need to use read to retrieve the
omap_dm_timer_enable(timer);
- if (!(timer->capability & OMAP_TIMER_ALWON)) {
- if (timer->get_context_loss_count &&
- timer->get_context_loss_count(&timer->pdev->dev) !=
- timer->ctx_loss_count)
- omap_timer_restore_context(timer);
- }
-
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
if (autoreload) {
l |= OMAP_TIMER_CTRL_AR;
}
EXPORT_SYMBOL_GPL(omap_dm_timers_active);
+static const struct of_device_id omap_timer_match[];
+
/**
* omap_dm_timer_probe - probe function called for every registered device
* @pdev: pointer to current timer platform device
struct omap_dm_timer *timer;
struct resource *mem, *irq;
struct device *dev = &pdev->dev;
- struct dmtimer_platform_data *pdata = pdev->dev.platform_data;
+ const struct of_device_id *match;
+ const struct dmtimer_platform_data *pdata;
+
+ match = of_match_device(of_match_ptr(omap_timer_match), dev);
+ pdata = match ? match->data : dev->platform_data;
if (!pdata && !dev->of_node) {
dev_err(dev, "%s: no platform data.\n", __func__);
timer->capability |= OMAP_TIMER_SECURE;
} else {
timer->id = pdev->id;
- timer->errata = pdata->timer_errata;
timer->capability = pdata->timer_capability;
timer->reserved = omap_dm_timer_reserved_systimer(timer->id);
timer->get_context_loss_count = pdata->get_context_loss_count;
}
+ if (pdata)
+ timer->errata = pdata->timer_errata;
+
timer->irq = irq->start;
timer->pdev = pdev;
return ret;
}
+static const struct dmtimer_platform_data omap3plus_pdata = {
+ .timer_errata = OMAP_TIMER_ERRATA_I103_I767,
+};
+
static const struct of_device_id omap_timer_match[] = {
- { .compatible = "ti,omap2-timer", },
+ {
+ .compatible = "ti,omap2420-timer",
+ },
+ {
+ .compatible = "ti,omap3430-timer",
+ .data = &omap3plus_pdata,
+ },
+ {
+ .compatible = "ti,omap4430-timer",
+ .data = &omap3plus_pdata,
+ },
+ {
+ .compatible = "ti,omap5430-timer",
+ .data = &omap3plus_pdata,
+ },
+ {
+ .compatible = "ti,am335x-timer",
+ .data = &omap3plus_pdata,
+ },
+ {
+ .compatible = "ti,am335x-timer-1ms",
+ .data = &omap3plus_pdata,
+ },
{},
};
MODULE_DEVICE_TABLE(of, omap_timer_match);
struct omap_dm_timer *omap_dm_timer_request(void);
struct omap_dm_timer *omap_dm_timer_request_specific(int timer_id);
struct omap_dm_timer *omap_dm_timer_request_by_cap(u32 cap);
+struct omap_dm_timer *omap_dm_timer_request_by_node(struct device_node *np);
int omap_dm_timer_free(struct omap_dm_timer *timer);
void omap_dm_timer_enable(struct omap_dm_timer *timer);
void omap_dm_timer_disable(struct omap_dm_timer *timer);
#include <linux/stmp_device.h>
#include <linux/of.h>
#include <linux/of_device.h>
+#include <linux/of_dma.h>
#include <asm/irq.h>
struct dma_device dma_device;
struct device_dma_parameters dma_parms;
struct mxs_dma_chan mxs_chans[MXS_DMA_CHANNELS];
+ struct platform_device *pdev;
+ unsigned int nr_channels;
};
struct mxs_dma_type {
struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
int ret;
- if (!data)
- return -EINVAL;
-
- mxs_chan->chan_irq = data->chan_irq;
+ if (data)
+ mxs_chan->chan_irq = data->chan_irq;
mxs_chan->ccw = dma_alloc_coherent(mxs_dma->dma_device.dev,
CCW_BLOCK_SIZE, &mxs_chan->ccw_phys,
return ret;
}
+struct mxs_dma_filter_param {
+ struct device_node *of_node;
+ unsigned int chan_id;
+};
+
+static bool mxs_dma_filter_fn(struct dma_chan *chan, void *fn_param)
+{
+ struct mxs_dma_filter_param *param = fn_param;
+ struct mxs_dma_chan *mxs_chan = to_mxs_dma_chan(chan);
+ struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
+ int chan_irq;
+
+ if (mxs_dma->dma_device.dev->of_node != param->of_node)
+ return false;
+
+ if (chan->chan_id != param->chan_id)
+ return false;
+
+ chan_irq = platform_get_irq(mxs_dma->pdev, param->chan_id);
+ if (chan_irq < 0)
+ return false;
+
+ mxs_chan->chan_irq = chan_irq;
+
+ return true;
+}
+
+struct dma_chan *mxs_dma_xlate(struct of_phandle_args *dma_spec,
+ struct of_dma *ofdma)
+{
+ struct mxs_dma_engine *mxs_dma = ofdma->of_dma_data;
+ dma_cap_mask_t mask = mxs_dma->dma_device.cap_mask;
+ struct mxs_dma_filter_param param;
+
+ if (dma_spec->args_count != 1)
+ return NULL;
+
+ param.of_node = ofdma->of_node;
+ param.chan_id = dma_spec->args[0];
+
+ if (param.chan_id >= mxs_dma->nr_channels)
+ return NULL;
+
+ return dma_request_channel(mask, mxs_dma_filter_fn, ¶m);
+}
+
static int __init mxs_dma_probe(struct platform_device *pdev)
{
+ struct device_node *np = pdev->dev.of_node;
const struct platform_device_id *id_entry;
const struct of_device_id *of_id;
const struct mxs_dma_type *dma_type;
struct resource *iores;
int ret, i;
- mxs_dma = kzalloc(sizeof(*mxs_dma), GFP_KERNEL);
+ mxs_dma = devm_kzalloc(&pdev->dev, sizeof(*mxs_dma), GFP_KERNEL);
if (!mxs_dma)
return -ENOMEM;
+ ret = of_property_read_u32(np, "dma-channels", &mxs_dma->nr_channels);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to read dma-channels\n");
+ return ret;
+ }
+
of_id = of_match_device(mxs_dma_dt_ids, &pdev->dev);
if (of_id)
id_entry = of_id->data;
mxs_dma->dev_id = dma_type->id;
iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mxs_dma->base = devm_ioremap_resource(&pdev->dev, iores);
+ if (IS_ERR(mxs_dma->base))
+ return PTR_ERR(mxs_dma->base);
- if (!request_mem_region(iores->start, resource_size(iores),
- pdev->name)) {
- ret = -EBUSY;
- goto err_request_region;
- }
-
- mxs_dma->base = ioremap(iores->start, resource_size(iores));
- if (!mxs_dma->base) {
- ret = -ENOMEM;
- goto err_ioremap;
- }
-
- mxs_dma->clk = clk_get(&pdev->dev, NULL);
- if (IS_ERR(mxs_dma->clk)) {
- ret = PTR_ERR(mxs_dma->clk);
- goto err_clk;
- }
+ mxs_dma->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(mxs_dma->clk))
+ return PTR_ERR(mxs_dma->clk);
dma_cap_set(DMA_SLAVE, mxs_dma->dma_device.cap_mask);
dma_cap_set(DMA_CYCLIC, mxs_dma->dma_device.cap_mask);
ret = mxs_dma_init(mxs_dma);
if (ret)
- goto err_init;
+ return ret;
+ mxs_dma->pdev = pdev;
mxs_dma->dma_device.dev = &pdev->dev;
/* mxs_dma gets 65535 bytes maximum sg size */
ret = dma_async_device_register(&mxs_dma->dma_device);
if (ret) {
dev_err(mxs_dma->dma_device.dev, "unable to register\n");
- goto err_init;
+ return ret;
+ }
+
+ ret = of_dma_controller_register(np, mxs_dma_xlate, mxs_dma);
+ if (ret) {
+ dev_err(mxs_dma->dma_device.dev,
+ "failed to register controller\n");
+ dma_async_device_unregister(&mxs_dma->dma_device);
}
dev_info(mxs_dma->dma_device.dev, "initialized\n");
return 0;
-
-err_init:
- clk_put(mxs_dma->clk);
-err_clk:
- iounmap(mxs_dma->base);
-err_ioremap:
- release_mem_region(iores->start, resource_size(iores));
-err_request_region:
- kfree(mxs_dma);
- return ret;
}
static struct platform_driver mxs_dma_driver = {
#include <linux/of_i2c.h>
#include <linux/dma-mapping.h>
#include <linux/dmaengine.h>
-#include <linux/fsl/mxs-dma.h>
#define DRIVER_NAME "mxs-i2c"
uint32_t timing1;
/* DMA support components */
- int dma_channel;
struct dma_chan *dmach;
- struct mxs_dma_data dma_data;
uint32_t pio_data[2];
uint32_t addr_data;
struct scatterlist sg_io[2];
.functionality = mxs_i2c_func,
};
-static bool mxs_i2c_dma_filter(struct dma_chan *chan, void *param)
-{
- struct mxs_i2c_dev *i2c = param;
-
- if (!mxs_dma_is_apbx(chan))
- return false;
-
- if (chan->chan_id != i2c->dma_channel)
- return false;
-
- chan->private = &i2c->dma_data;
-
- return true;
-}
-
static void mxs_i2c_derive_timing(struct mxs_i2c_dev *i2c, int speed)
{
/* The I2C block clock run at 24MHz */
struct device_node *node = dev->of_node;
int ret;
- /*
- * TODO: This is a temporary solution and should be changed
- * to use generic DMA binding later when the helpers get in.
- */
- ret = of_property_read_u32(node, "fsl,i2c-dma-channel",
- &i2c->dma_channel);
- if (ret) {
- dev_err(dev, "Failed to get DMA channel!\n");
- return -ENODEV;
- }
-
ret = of_property_read_u32(node, "clock-frequency", &speed);
if (ret) {
dev_warn(dev, "No I2C speed selected, using 100kHz\n");
struct pinctrl *pinctrl;
struct resource *res;
resource_size_t res_size;
- int err, irq, dmairq;
- dma_cap_mask_t mask;
+ int err, irq;
pinctrl = devm_pinctrl_get_select_default(dev);
if (IS_ERR(pinctrl))
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
irq = platform_get_irq(pdev, 0);
- dmairq = platform_get_irq(pdev, 1);
- if (!res || irq < 0 || dmairq < 0)
+ if (!res || irq < 0)
return -ENOENT;
res_size = resource_size(res);
}
/* Setup the DMA */
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
- i2c->dma_data.chan_irq = dmairq;
- i2c->dmach = dma_request_channel(mask, mxs_i2c_dma_filter, i2c);
+ i2c->dmach = dma_request_slave_channel(dev, "rx-tx");
if (!i2c->dmach) {
dev_err(dev, "Failed to request dma\n");
return -ENODEV;
.enable_sdio_irq = mxs_mmc_enable_sdio_irq,
};
-static bool mxs_mmc_dma_filter(struct dma_chan *chan, void *param)
-{
- struct mxs_mmc_host *host = param;
- struct mxs_ssp *ssp = &host->ssp;
-
- if (!mxs_dma_is_apbh(chan))
- return false;
-
- if (chan->chan_id != ssp->dma_channel)
- return false;
-
- chan->private = &ssp->dma_data;
-
- return true;
-}
-
static struct platform_device_id mxs_ssp_ids[] = {
{
.name = "imx23-mmc",
struct device_node *np = pdev->dev.of_node;
struct mxs_mmc_host *host;
struct mmc_host *mmc;
- struct resource *iores, *dmares;
+ struct resource *iores;
struct pinctrl *pinctrl;
- int ret = 0, irq_err, irq_dma;
- dma_cap_mask_t mask;
+ int ret = 0, irq_err;
struct regulator *reg_vmmc;
enum of_gpio_flags flags;
struct mxs_ssp *ssp;
u32 bus_width = 0;
iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- dmares = platform_get_resource(pdev, IORESOURCE_DMA, 0);
irq_err = platform_get_irq(pdev, 0);
- irq_dma = platform_get_irq(pdev, 1);
- if (!iores || irq_err < 0 || irq_dma < 0)
+ if (!iores || irq_err < 0)
return -EINVAL;
mmc = mmc_alloc_host(sizeof(struct mxs_mmc_host), &pdev->dev);
goto out_mmc_free;
}
- if (np) {
- ssp->devid = (enum mxs_ssp_id) of_id->data;
- /*
- * TODO: This is a temporary solution and should be changed
- * to use generic DMA binding later when the helpers get in.
- */
- ret = of_property_read_u32(np, "fsl,ssp-dma-channel",
- &ssp->dma_channel);
- if (ret) {
- dev_err(mmc_dev(host->mmc),
- "failed to get dma channel\n");
- goto out_mmc_free;
- }
- } else {
- ssp->devid = pdev->id_entry->driver_data;
- ssp->dma_channel = dmares->start;
- }
+ ssp->devid = (enum mxs_ssp_id) of_id->data;
host->mmc = mmc;
host->sdio_irq_en = 0;
mxs_mmc_reset(host);
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
- ssp->dma_data.chan_irq = irq_dma;
- ssp->dmach = dma_request_channel(mask, mxs_mmc_dma_filter, host);
+ ssp->dmach = dma_request_slave_channel(&pdev->dev, "rx-tx");
if (!ssp->dmach) {
dev_err(mmc_dev(host->mmc),
"%s: failed to request dma\n", __func__);
#define GPMI_NAND_GPMI_REGS_ADDR_RES_NAME "gpmi-nand"
#define GPMI_NAND_BCH_REGS_ADDR_RES_NAME "bch"
#define GPMI_NAND_BCH_INTERRUPT_RES_NAME "bch"
-#define GPMI_NAND_DMA_INTERRUPT_RES_NAME "gpmi-dma"
/* add our owner bbt descriptor */
static uint8_t scan_ff_pattern[] = { 0xff };
free_irq(i, this);
}
-static bool gpmi_dma_filter(struct dma_chan *chan, void *param)
-{
- struct gpmi_nand_data *this = param;
- int dma_channel = (int)this->private;
-
- if (!mxs_dma_is_apbh(chan))
- return false;
- /*
- * only catch the GPMI dma channels :
- * for mx23 : MX23_DMA_GPMI0 ~ MX23_DMA_GPMI3
- * (These four channels share the same IRQ!)
- *
- * for mx28 : MX28_DMA_GPMI0 ~ MX28_DMA_GPMI7
- * (These eight channels share the same IRQ!)
- */
- if (dma_channel == chan->chan_id) {
- chan->private = &this->dma_data;
- return true;
- }
- return false;
-}
-
static void release_dma_channels(struct gpmi_nand_data *this)
{
unsigned int i;
static int acquire_dma_channels(struct gpmi_nand_data *this)
{
struct platform_device *pdev = this->pdev;
- struct resource *r_dma;
- struct device_node *dn;
- u32 dma_channel;
- int ret;
struct dma_chan *dma_chan;
- dma_cap_mask_t mask;
-
- /* dma channel, we only use the first one. */
- dn = pdev->dev.of_node;
- ret = of_property_read_u32(dn, "fsl,gpmi-dma-channel", &dma_channel);
- if (ret) {
- pr_err("unable to get DMA channel from dt.\n");
- goto acquire_err;
- }
- this->private = (void *)dma_channel;
-
- /* gpmi dma interrupt */
- r_dma = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
- GPMI_NAND_DMA_INTERRUPT_RES_NAME);
- if (!r_dma) {
- pr_err("Can't get resource for DMA\n");
- goto acquire_err;
- }
- this->dma_data.chan_irq = r_dma->start;
/* request dma channel */
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
-
- dma_chan = dma_request_channel(mask, gpmi_dma_filter, this);
+ dma_chan = dma_request_slave_channel(&pdev->dev, "rx-tx");
if (!dma_chan) {
pr_err("Failed to request DMA channel.\n");
goto acquire_err;
#include <linux/mtd/nand.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
-#include <linux/fsl/mxs-dma.h>
+#include <linux/dmaengine.h>
#define GPMI_CLK_MAX 5 /* MX6Q needs five clocks */
struct resources {
/* DMA channels */
#define DMA_CHANS 8
struct dma_chan *dma_chans[DMA_CHANS];
- struct mxs_dma_data dma_data;
enum dma_ops_type last_dma_type;
enum dma_ops_type dma_type;
struct completion dma_done;
struct clk *clk_ipg;
struct clk *clk_ahb;
+ struct clk *clk_enet_out;
struct clk *clk_ptp;
/* The saved address of a sent-in-place packet/buffer, for skfree(). */
goto failed_clk;
}
+ /* enet_out is optional, depends on board */
+ fep->clk_enet_out = devm_clk_get(&pdev->dev, "enet_out");
+ if (IS_ERR(fep->clk_enet_out))
+ fep->clk_enet_out = NULL;
+
fep->clk_ptp = devm_clk_get(&pdev->dev, "ptp");
fep->bufdesc_ex =
pdev->id_entry->driver_data & FEC_QUIRK_HAS_BUFDESC_EX;
if (IS_ERR(fep->clk_ptp)) {
- ret = PTR_ERR(fep->clk_ptp);
+ fep->clk_ptp = NULL;
fep->bufdesc_ex = 0;
}
clk_prepare_enable(fep->clk_ahb);
clk_prepare_enable(fep->clk_ipg);
- if (!IS_ERR(fep->clk_ptp))
- clk_prepare_enable(fep->clk_ptp);
+ clk_prepare_enable(fep->clk_enet_out);
+ clk_prepare_enable(fep->clk_ptp);
reg_phy = devm_regulator_get(&pdev->dev, "phy");
if (!IS_ERR(reg_phy)) {
failed_regulator:
clk_disable_unprepare(fep->clk_ahb);
clk_disable_unprepare(fep->clk_ipg);
- if (!IS_ERR(fep->clk_ptp))
- clk_disable_unprepare(fep->clk_ptp);
+ clk_disable_unprepare(fep->clk_enet_out);
+ clk_disable_unprepare(fep->clk_ptp);
failed_pin:
failed_clk:
failed_ioremap:
clk_disable_unprepare(fep->clk_ptp);
if (fep->ptp_clock)
ptp_clock_unregister(fep->ptp_clock);
+ clk_disable_unprepare(fep->clk_enet_out);
clk_disable_unprepare(fep->clk_ahb);
clk_disable_unprepare(fep->clk_ipg);
for (i = 0; i < FEC_IRQ_NUM; i++) {
fec_stop(ndev);
netif_device_detach(ndev);
}
+ clk_disable_unprepare(fep->clk_enet_out);
clk_disable_unprepare(fep->clk_ahb);
clk_disable_unprepare(fep->clk_ipg);
struct net_device *ndev = dev_get_drvdata(dev);
struct fec_enet_private *fep = netdev_priv(ndev);
+ clk_prepare_enable(fep->clk_enet_out);
clk_prepare_enable(fep->clk_ahb);
clk_prepare_enable(fep->clk_ipg);
if (netif_running(ndev)) {
#if defined(CONFIG_OF)
static const struct of_device_id davinci_spi_of_match[] = {
{
- .compatible = "ti,dm644x-spi",
+ .compatible = "ti,dm6441-spi",
},
{
- .compatible = "ti,da8xx-spi",
+ .compatible = "ti,da830-spi",
.data = (void *)SPI_VERSION_2,
},
{ },
return status;
}
-static bool mxs_ssp_dma_filter(struct dma_chan *chan, void *param)
-{
- struct mxs_ssp *ssp = param;
-
- if (!mxs_dma_is_apbh(chan))
- return false;
-
- if (chan->chan_id != ssp->dma_channel)
- return false;
-
- chan->private = &ssp->dma_data;
-
- return true;
-}
-
static const struct of_device_id mxs_spi_dt_ids[] = {
{ .compatible = "fsl,imx23-spi", .data = (void *) IMX23_SSP, },
{ .compatible = "fsl,imx28-spi", .data = (void *) IMX28_SSP, },
struct spi_master *master;
struct mxs_spi *spi;
struct mxs_ssp *ssp;
- struct resource *iores, *dmares;
+ struct resource *iores;
struct pinctrl *pinctrl;
struct clk *clk;
void __iomem *base;
- int devid, dma_channel, clk_freq;
- int ret = 0, irq_err, irq_dma;
- dma_cap_mask_t mask;
+ int devid, clk_freq;
+ int ret = 0, irq_err;
/*
* Default clock speed for the SPI core. 160MHz seems to
iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
irq_err = platform_get_irq(pdev, 0);
- irq_dma = platform_get_irq(pdev, 1);
- if (!iores || irq_err < 0 || irq_dma < 0)
+ if (!iores || irq_err < 0)
return -EINVAL;
base = devm_ioremap_resource(&pdev->dev, iores);
if (IS_ERR(clk))
return PTR_ERR(clk);
- if (np) {
- devid = (enum mxs_ssp_id) of_id->data;
- /*
- * TODO: This is a temporary solution and should be changed
- * to use generic DMA binding later when the helpers get in.
- */
- ret = of_property_read_u32(np, "fsl,ssp-dma-channel",
- &dma_channel);
- if (ret) {
- dev_err(&pdev->dev,
- "Failed to get DMA channel\n");
- return -EINVAL;
- }
-
- ret = of_property_read_u32(np, "clock-frequency",
- &clk_freq);
- if (ret)
- clk_freq = clk_freq_default;
- } else {
- dmares = platform_get_resource(pdev, IORESOURCE_DMA, 0);
- if (!dmares)
- return -EINVAL;
- devid = pdev->id_entry->driver_data;
- dma_channel = dmares->start;
+ devid = (enum mxs_ssp_id) of_id->data;
+ ret = of_property_read_u32(np, "clock-frequency",
+ &clk_freq);
+ if (ret)
clk_freq = clk_freq_default;
- }
master = spi_alloc_master(&pdev->dev, sizeof(*spi));
if (!master)
ssp->clk = clk;
ssp->base = base;
ssp->devid = devid;
- ssp->dma_channel = dma_channel;
init_completion(&spi->c);
if (ret)
goto out_master_free;
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
- ssp->dma_data.chan_irq = irq_dma;
- ssp->dmach = dma_request_channel(mask, mxs_ssp_dma_filter, ssp);
+ ssp->dmach = dma_request_slave_channel(&pdev->dev, "rx-tx");
if (!ssp->dmach) {
dev_err(ssp->dev, "Failed to request DMA\n");
ret = -ENODEV;
#include <linux/pinctrl/consumer.h>
#include <linux/of_device.h>
#include <linux/dma-mapping.h>
-#include <linux/fsl/mxs-dma.h>
+#include <linux/dmaengine.h>
#include <asm/cacheflush.h>
struct device *dev;
/* for DMA */
- struct mxs_dma_data dma_data;
- int dma_channel_rx, dma_channel_tx;
- int dma_irq_rx, dma_irq_tx;
- int dma_channel;
-
struct scatterlist tx_sgl;
struct dma_chan *tx_dma_chan;
void *tx_dma_buf;
return mctrl;
}
-static bool mxs_auart_dma_filter(struct dma_chan *chan, void *param)
-{
- struct mxs_auart_port *s = param;
-
- if (!mxs_dma_is_apbx(chan))
- return false;
-
- if (s->dma_channel == chan->chan_id) {
- chan->private = &s->dma_data;
- return true;
- }
- return false;
-}
-
static int mxs_auart_dma_prep_rx(struct mxs_auart_port *s);
static void dma_rx_callback(void *arg)
{
static int mxs_auart_dma_init(struct mxs_auart_port *s)
{
- dma_cap_mask_t mask;
-
if (auart_dma_enabled(s))
return 0;
- /* We do not get the right DMA channels. */
- if (s->dma_channel_rx == -1 || s->dma_channel_tx == -1)
- return -EINVAL;
-
/* init for RX */
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
- s->dma_channel = s->dma_channel_rx;
- s->dma_data.chan_irq = s->dma_irq_rx;
- s->rx_dma_chan = dma_request_channel(mask, mxs_auart_dma_filter, s);
+ s->rx_dma_chan = dma_request_slave_channel(s->dev, "rx");
if (!s->rx_dma_chan)
goto err_out;
s->rx_dma_buf = kzalloc(UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA);
goto err_out;
/* init for TX */
- s->dma_channel = s->dma_channel_tx;
- s->dma_data.chan_irq = s->dma_irq_tx;
- s->tx_dma_chan = dma_request_channel(mask, mxs_auart_dma_filter, s);
+ s->tx_dma_chan = dma_request_slave_channel(s->dev, "tx");
if (!s->tx_dma_chan)
goto err_out;
s->tx_dma_buf = kzalloc(UART_XMIT_SIZE, GFP_KERNEL | GFP_DMA);
struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
- u32 dma_channel[2];
int ret;
if (!np)
}
s->port.line = ret;
- s->dma_irq_rx = platform_get_irq(pdev, 1);
- s->dma_irq_tx = platform_get_irq(pdev, 2);
+ s->flags |= MXS_AUART_DMA_CONFIG;
- ret = of_property_read_u32_array(np, "fsl,auart-dma-channel",
- dma_channel, 2);
- if (ret == 0) {
- s->dma_channel_rx = dma_channel[0];
- s->dma_channel_tx = dma_channel[1];
-
- s->flags |= MXS_AUART_DMA_CONFIG;
- } else {
- s->dma_channel_rx = -1;
- s->dma_channel_tx = -1;
- }
return 0;
}
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
+ select FB_MODE_HELPERS
+ select OF_VIDEOMODE
help
Framebuffer support for the MXS SoC.
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/of_device.h>
-#include <linux/of_gpio.h>
+#include <video/of_display_timing.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/io.h>
#include <linux/pinctrl/consumer.h>
-#include <linux/mxsfb.h>
+#include <linux/fb.h>
+#include <linux/regulator/consumer.h>
+#include <video/videomode.h>
#define REG_SET 4
#define REG_CLR 8
#define VDCTRL0_ENABLE_PRESENT (1 << 28)
#define VDCTRL0_VSYNC_ACT_HIGH (1 << 27)
#define VDCTRL0_HSYNC_ACT_HIGH (1 << 26)
-#define VDCTRL0_DOTCLK_ACT_FAILING (1 << 25)
+#define VDCTRL0_DOTCLK_ACT_FALLING (1 << 25)
#define VDCTRL0_ENABLE_ACT_HIGH (1 << 24)
#define VDCTRL0_VSYNC_PERIOD_UNIT (1 << 21)
#define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT (1 << 20)
#define BLUE 2
#define TRANSP 3
+#define STMLCDIF_8BIT 1 /** pixel data bus to the display is of 8 bit width */
+#define STMLCDIF_16BIT 0 /** pixel data bus to the display is of 16 bit width */
+#define STMLCDIF_18BIT 2 /** pixel data bus to the display is of 18 bit width */
+#define STMLCDIF_24BIT 3 /** pixel data bus to the display is of 24 bit width */
+
+#define MXSFB_SYNC_DATA_ENABLE_HIGH_ACT (1 << 6)
+#define MXSFB_SYNC_DOTCLK_FALLING_ACT (1 << 7) /* negtive edge sampling */
+
enum mxsfb_devtype {
MXSFB_V3,
MXSFB_V4,
unsigned ld_intf_width;
unsigned dotclk_delay;
const struct mxsfb_devdata *devdata;
- int mapped;
u32 sync;
+ struct regulator *reg_lcd;
};
#define mxsfb_is_v3(host) (host->devdata->ipversion == 3)
{
struct mxsfb_info *host = to_imxfb_host(fb_info);
u32 reg;
+ int ret;
dev_dbg(&host->pdev->dev, "%s\n", __func__);
+ if (host->reg_lcd) {
+ ret = regulator_enable(host->reg_lcd);
+ if (ret) {
+ dev_err(&host->pdev->dev,
+ "lcd regulator enable failed: %d\n", ret);
+ return;
+ }
+ }
+
clk_prepare_enable(host->clk);
clk_set_rate(host->clk, PICOS2KHZ(fb_info->var.pixclock) * 1000U);
struct mxsfb_info *host = to_imxfb_host(fb_info);
unsigned loop;
u32 reg;
+ int ret;
dev_dbg(&host->pdev->dev, "%s\n", __func__);
clk_disable_unprepare(host->clk);
host->enabled = 0;
+
+ if (host->reg_lcd) {
+ ret = regulator_disable(host->reg_lcd);
+ if (ret)
+ dev_err(&host->pdev->dev,
+ "lcd regulator disable failed: %d\n", ret);
+ }
}
static int mxsfb_set_par(struct fb_info *fb_info)
vdctrl0 |= VDCTRL0_VSYNC_ACT_HIGH;
if (host->sync & MXSFB_SYNC_DATA_ENABLE_HIGH_ACT)
vdctrl0 |= VDCTRL0_ENABLE_ACT_HIGH;
- if (host->sync & MXSFB_SYNC_DOTCLK_FAILING_ACT)
- vdctrl0 |= VDCTRL0_DOTCLK_ACT_FAILING;
+ if (host->sync & MXSFB_SYNC_DOTCLK_FALLING_ACT)
+ vdctrl0 |= VDCTRL0_DOTCLK_ACT_FALLING;
writel(vdctrl0, host->base + LCDC_VDCTRL0);
return 0;
}
+static int mxsfb_init_fbinfo_dt(struct mxsfb_info *host)
+{
+ struct fb_info *fb_info = &host->fb_info;
+ struct fb_var_screeninfo *var = &fb_info->var;
+ struct device *dev = &host->pdev->dev;
+ struct device_node *np = host->pdev->dev.of_node;
+ struct device_node *display_np;
+ struct device_node *timings_np;
+ struct display_timings *timings;
+ u32 width;
+ int i;
+ int ret = 0;
+
+ display_np = of_parse_phandle(np, "display", 0);
+ if (!display_np) {
+ dev_err(dev, "failed to find display phandle\n");
+ return -ENOENT;
+ }
+
+ ret = of_property_read_u32(display_np, "bus-width", &width);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property bus-width\n");
+ goto put_display_node;
+ }
+
+ switch (width) {
+ case 8:
+ host->ld_intf_width = STMLCDIF_8BIT;
+ break;
+ case 16:
+ host->ld_intf_width = STMLCDIF_16BIT;
+ break;
+ case 18:
+ host->ld_intf_width = STMLCDIF_18BIT;
+ break;
+ case 24:
+ host->ld_intf_width = STMLCDIF_24BIT;
+ break;
+ default:
+ dev_err(dev, "invalid bus-width value\n");
+ ret = -EINVAL;
+ goto put_display_node;
+ }
+
+ ret = of_property_read_u32(display_np, "bits-per-pixel",
+ &var->bits_per_pixel);
+ if (ret < 0) {
+ dev_err(dev, "failed to get property bits-per-pixel\n");
+ goto put_display_node;
+ }
+
+ timings = of_get_display_timings(display_np);
+ if (!timings) {
+ dev_err(dev, "failed to get display timings\n");
+ ret = -ENOENT;
+ goto put_display_node;
+ }
+
+ timings_np = of_find_node_by_name(display_np,
+ "display-timings");
+ if (!timings_np) {
+ dev_err(dev, "failed to find display-timings node\n");
+ ret = -ENOENT;
+ goto put_display_node;
+ }
+
+ for (i = 0; i < of_get_child_count(timings_np); i++) {
+ struct videomode vm;
+ struct fb_videomode fb_vm;
+
+ ret = videomode_from_timing(timings, &vm, i);
+ if (ret < 0)
+ goto put_timings_node;
+ ret = fb_videomode_from_videomode(&vm, &fb_vm);
+ if (ret < 0)
+ goto put_timings_node;
+
+ if (vm.data_flags & DISPLAY_FLAGS_DE_HIGH)
+ host->sync |= MXSFB_SYNC_DATA_ENABLE_HIGH_ACT;
+ if (vm.data_flags & DISPLAY_FLAGS_PIXDATA_NEGEDGE)
+ host->sync |= MXSFB_SYNC_DOTCLK_FALLING_ACT;
+ fb_add_videomode(&fb_vm, &fb_info->modelist);
+ }
+
+put_timings_node:
+ of_node_put(timings_np);
+put_display_node:
+ of_node_put(display_np);
+ return ret;
+}
+
static int mxsfb_init_fbinfo(struct mxsfb_info *host)
{
struct fb_info *fb_info = &host->fb_info;
struct fb_var_screeninfo *var = &fb_info->var;
- struct mxsfb_platform_data *pdata = host->pdev->dev.platform_data;
dma_addr_t fb_phys;
void *fb_virt;
- unsigned fb_size = pdata->fb_size;
+ unsigned fb_size;
+ int ret;
fb_info->fbops = &mxsfb_ops;
fb_info->flags = FBINFO_FLAG_DEFAULT | FBINFO_READS_FAST;
fb_info->fix.visual = FB_VISUAL_TRUECOLOR,
fb_info->fix.accel = FB_ACCEL_NONE;
- var->bits_per_pixel = pdata->default_bpp ? pdata->default_bpp : 16;
+ ret = mxsfb_init_fbinfo_dt(host);
+ if (ret)
+ return ret;
+
var->nonstd = 0;
var->activate = FB_ACTIVATE_NOW;
var->accel_flags = 0;
var->vmode = FB_VMODE_NONINTERLACED;
- host->dotclk_delay = pdata->dotclk_delay;
- host->ld_intf_width = pdata->ld_intf_width;
-
/* Memory allocation for framebuffer */
- if (pdata->fb_phys) {
- if (!fb_size)
- return -EINVAL;
-
- fb_phys = pdata->fb_phys;
-
- if (!request_mem_region(fb_phys, fb_size, host->pdev->name))
- return -ENOMEM;
+ fb_size = SZ_2M;
+ fb_virt = alloc_pages_exact(fb_size, GFP_DMA);
+ if (!fb_virt)
+ return -ENOMEM;
- fb_virt = ioremap(fb_phys, fb_size);
- if (!fb_virt) {
- release_mem_region(fb_phys, fb_size);
- return -ENOMEM;
- }
- host->mapped = 1;
- } else {
- if (!fb_size)
- fb_size = SZ_2M; /* default */
- fb_virt = alloc_pages_exact(fb_size, GFP_DMA);
- if (!fb_virt)
- return -ENOMEM;
-
- fb_phys = virt_to_phys(fb_virt);
- }
+ fb_phys = virt_to_phys(fb_virt);
fb_info->fix.smem_start = fb_phys;
fb_info->screen_base = fb_virt;
{
struct fb_info *fb_info = &host->fb_info;
- if (host->mapped) {
- iounmap(fb_info->screen_base);
- release_mem_region(fb_info->fix.smem_start,
- fb_info->screen_size);
- } else {
- free_pages_exact(fb_info->screen_base, fb_info->fix.smem_len);
- }
+ free_pages_exact(fb_info->screen_base, fb_info->fix.smem_len);
}
static struct platform_device_id mxsfb_devtype[] = {
{
const struct of_device_id *of_id =
of_match_device(mxsfb_dt_ids, &pdev->dev);
- struct mxsfb_platform_data *pdata = pdev->dev.platform_data;
struct resource *res;
struct mxsfb_info *host;
struct fb_info *fb_info;
struct fb_modelist *modelist;
struct pinctrl *pinctrl;
- int panel_enable;
- enum of_gpio_flags flags;
- int i, ret;
+ int ret;
if (of_id)
pdev->id_entry = of_id->data;
- if (!pdata) {
- dev_err(&pdev->dev, "No platformdata. Giving up\n");
- return -ENODEV;
- }
-
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "Cannot get memory IO resource\n");
return -ENODEV;
}
- if (!request_mem_region(res->start, resource_size(res), pdev->name))
- return -EBUSY;
-
fb_info = framebuffer_alloc(sizeof(struct mxsfb_info), &pdev->dev);
if (!fb_info) {
dev_err(&pdev->dev, "Failed to allocate fbdev\n");
- ret = -ENOMEM;
- goto error_alloc_info;
+ return -ENOMEM;
}
host = to_imxfb_host(fb_info);
- host->base = ioremap(res->start, resource_size(res));
- if (!host->base) {
+ host->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(host->base)) {
dev_err(&pdev->dev, "ioremap failed\n");
- ret = -ENOMEM;
- goto error_ioremap;
+ ret = PTR_ERR(host->base);
+ goto fb_release;
}
host->pdev = pdev;
pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
if (IS_ERR(pinctrl)) {
ret = PTR_ERR(pinctrl);
- goto error_getpin;
+ goto fb_release;
}
- host->clk = clk_get(&host->pdev->dev, NULL);
+ host->clk = devm_clk_get(&host->pdev->dev, NULL);
if (IS_ERR(host->clk)) {
ret = PTR_ERR(host->clk);
- goto error_getclock;
+ goto fb_release;
}
- panel_enable = of_get_named_gpio_flags(pdev->dev.of_node,
- "panel-enable-gpios", 0, &flags);
- if (gpio_is_valid(panel_enable)) {
- unsigned long f = GPIOF_OUT_INIT_HIGH;
- if (flags == OF_GPIO_ACTIVE_LOW)
- f = GPIOF_OUT_INIT_LOW;
- ret = devm_gpio_request_one(&pdev->dev, panel_enable,
- f, "panel-enable");
- if (ret) {
- dev_err(&pdev->dev,
- "failed to request gpio %d: %d\n",
- panel_enable, ret);
- goto error_panel_enable;
- }
- }
+ host->reg_lcd = devm_regulator_get(&pdev->dev, "lcd");
+ if (IS_ERR(host->reg_lcd))
+ host->reg_lcd = NULL;
- fb_info->pseudo_palette = kmalloc(sizeof(u32) * 16, GFP_KERNEL);
+ fb_info->pseudo_palette = devm_kzalloc(&pdev->dev, sizeof(u32) * 16,
+ GFP_KERNEL);
if (!fb_info->pseudo_palette) {
ret = -ENOMEM;
- goto error_pseudo_pallette;
+ goto fb_release;
}
INIT_LIST_HEAD(&fb_info->modelist);
- host->sync = pdata->sync;
-
ret = mxsfb_init_fbinfo(host);
if (ret != 0)
- goto error_init_fb;
-
- for (i = 0; i < pdata->mode_count; i++)
- fb_add_videomode(&pdata->mode_list[i], &fb_info->modelist);
+ goto fb_release;
modelist = list_first_entry(&fb_info->modelist,
struct fb_modelist, list);
ret = register_framebuffer(fb_info);
if (ret != 0) {
dev_err(&pdev->dev,"Failed to register framebuffer\n");
- goto error_register;
+ goto fb_destroy;
}
if (!host->enabled) {
return 0;
-error_register:
+fb_destroy:
if (host->enabled)
clk_disable_unprepare(host->clk);
fb_destroy_modelist(&fb_info->modelist);
-error_init_fb:
- kfree(fb_info->pseudo_palette);
-error_pseudo_pallette:
-error_panel_enable:
- clk_put(host->clk);
-error_getclock:
-error_getpin:
- iounmap(host->base);
-error_ioremap:
+fb_release:
framebuffer_release(fb_info);
-error_alloc_info:
- release_mem_region(res->start, resource_size(res));
return ret;
}
{
struct fb_info *fb_info = platform_get_drvdata(pdev);
struct mxsfb_info *host = to_imxfb_host(fb_info);
- struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (host->enabled)
mxsfb_disable_controller(fb_info);
unregister_framebuffer(fb_info);
- kfree(fb_info->pseudo_palette);
mxsfb_free_videomem(host);
- iounmap(host->base);
- clk_put(host->clk);
framebuffer_release(fb_info);
- release_mem_region(res->start, resource_size(res));
platform_set_drvdata(pdev, NULL);
+++ /dev/null
-/*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#ifndef __LINUX_MXSFB_H
-#define __LINUX_MXSFB_H
-
-#include <linux/fb.h>
-
-#define STMLCDIF_8BIT 1 /** pixel data bus to the display is of 8 bit width */
-#define STMLCDIF_16BIT 0 /** pixel data bus to the display is of 16 bit width */
-#define STMLCDIF_18BIT 2 /** pixel data bus to the display is of 18 bit width */
-#define STMLCDIF_24BIT 3 /** pixel data bus to the display is of 24 bit width */
-
-#define MXSFB_SYNC_DATA_ENABLE_HIGH_ACT (1 << 6)
-#define MXSFB_SYNC_DOTCLK_FAILING_ACT (1 << 7) /* failing/negtive edge sampling */
-
-struct mxsfb_platform_data {
- struct fb_videomode *mode_list;
- unsigned mode_count;
-
- unsigned default_bpp;
-
- unsigned dotclk_delay; /* refer manual HW_LCDIF_VDCTRL4 register */
- unsigned ld_intf_width; /* refer STMLCDIF_* macros */
-
- unsigned fb_size; /* Size of the video memory. If zero a
- * default will be used
- */
- unsigned long fb_phys; /* physical address for the video memory. If
- * zero the framebuffer memory will be dynamically
- * allocated. If specified,fb_size must also be specified.
- * fb_phys must be unused by Linux.
- */
- u32 sync; /* sync mask, contains MXSFB specifics not
- * carried in fb_info->var.sync
- */
-};
-
-#endif /* __LINUX_MXSFB_H */
#ifndef __LINUX_SPI_MXS_SPI_H__
#define __LINUX_SPI_MXS_SPI_H__
-#include <linux/fsl/mxs-dma.h>
+#include <linux/dmaengine.h>
#define ssp_is_old(host) ((host)->devid == IMX23_SSP)
unsigned int clk_rate;
enum mxs_ssp_id devid;
- int dma_channel;
struct dma_chan *dmach;
- struct mxs_dma_data dma_data;
unsigned int dma_dir;
enum dma_transfer_direction slave_dirn;
u32 ssp_pio_words[SSP_PIO_NUM];
projects / linux-2.6-block.git / commitdiff