#ifndef _UAPI_LINUX_ETHTOOL_H
#define _UAPI_LINUX_ETHTOOL_H
+#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/if_ether.h>
+#ifndef __KERNEL__
+#include <limits.h> /* for INT_MAX */
+#endif
+
/* All structures exposed to userland should be defined such that they
* have the same layout for 32-bit and 64-bit userland.
*/
/**
- * struct ethtool_cmd - link control and status
+ * struct ethtool_cmd - DEPRECATED, link control and status
+ * This structure is DEPRECATED, please use struct ethtool_link_settings.
* @cmd: Command number = %ETHTOOL_GSET or %ETHTOOL_SSET
* @supported: Bitmask of %SUPPORTED_* flags for the link modes,
* physical connectors and other link features for which the
* physical connectors and other link features that are
* advertised through autonegotiation or enabled for
* auto-detection.
- * @speed: Low bits of the speed
+ * @speed: Low bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN
* @duplex: Duplex mode; one of %DUPLEX_*
* @port: Physical connector type; one of %PORT_*
* @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not
* obsoleted by &struct ethtool_coalesce. Read-only; deprecated.
* @maxrxpkt: Historically used to report RX IRQ coalescing; now
* obsoleted by &struct ethtool_coalesce. Read-only; deprecated.
- * @speed_hi: High bits of the speed
+ * @speed_hi: High bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN
* @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of
* %ETH_TP_MDI_*. If the status is unknown or not applicable, the
* value will be %ETH_TP_MDI_INVALID. Read-only.
__u8 proto;
};
+/**
+ * struct ethtool_tcpip6_spec - flow specification for TCP/IPv6 etc.
+ * @ip6src: Source host
+ * @ip6dst: Destination host
+ * @psrc: Source port
+ * @pdst: Destination port
+ * @tclass: Traffic Class
+ *
+ * This can be used to specify a TCP/IPv6, UDP/IPv6 or SCTP/IPv6 flow.
+ */
+struct ethtool_tcpip6_spec {
+ __be32 ip6src[4];
+ __be32 ip6dst[4];
+ __be16 psrc;
+ __be16 pdst;
+ __u8 tclass;
+};
+
+/**
+ * struct ethtool_ah_espip6_spec - flow specification for IPsec/IPv6
+ * @ip6src: Source host
+ * @ip6dst: Destination host
+ * @spi: Security parameters index
+ * @tclass: Traffic Class
+ *
+ * This can be used to specify an IPsec transport or tunnel over IPv6.
+ */
+struct ethtool_ah_espip6_spec {
+ __be32 ip6src[4];
+ __be32 ip6dst[4];
+ __be32 spi;
+ __u8 tclass;
+};
+
+/**
+ * struct ethtool_usrip6_spec - general flow specification for IPv6
+ * @ip6src: Source host
+ * @ip6dst: Destination host
+ * @l4_4_bytes: First 4 bytes of transport (layer 4) header
+ * @tclass: Traffic Class
+ * @l4_proto: Transport protocol number (nexthdr after any Extension Headers)
+ */
+struct ethtool_usrip6_spec {
+ __be32 ip6src[4];
+ __be32 ip6dst[4];
+ __be32 l4_4_bytes;
+ __u8 tclass;
+ __u8 l4_proto;
+};
+
union ethtool_flow_union {
struct ethtool_tcpip4_spec tcp_ip4_spec;
struct ethtool_tcpip4_spec udp_ip4_spec;
struct ethtool_ah_espip4_spec ah_ip4_spec;
struct ethtool_ah_espip4_spec esp_ip4_spec;
struct ethtool_usrip4_spec usr_ip4_spec;
+ struct ethtool_tcpip6_spec tcp_ip6_spec;
+ struct ethtool_tcpip6_spec udp_ip6_spec;
+ struct ethtool_tcpip6_spec sctp_ip6_spec;
+ struct ethtool_ah_espip6_spec ah_ip6_spec;
+ struct ethtool_ah_espip6_spec esp_ip6_spec;
+ struct ethtool_usrip6_spec usr_ip6_spec;
struct ethhdr ether_spec;
__u8 hdata[52];
};
#define ETHTOOL_F_WISH (1 << ETHTOOL_F_WISH__BIT)
#define ETHTOOL_F_COMPAT (1 << ETHTOOL_F_COMPAT__BIT)
+#define MAX_NUM_QUEUE 4096
+
+/**
+ * struct ethtool_per_queue_op - apply sub command to the queues in mask.
+ * @cmd: ETHTOOL_PERQUEUE
+ * @sub_command: the sub command which apply to each queues
+ * @queue_mask: Bitmap of the queues which sub command apply to
+ * @data: A complete command structure following for each of the queues addressed
+ */
+struct ethtool_per_queue_op {
+ __u32 cmd;
+ __u32 sub_command;
+ __u32 queue_mask[__KERNEL_DIV_ROUND_UP(MAX_NUM_QUEUE, 32)];
+ char data[];
+};
/* CMDs currently supported */
-#define ETHTOOL_GSET 0x00000001 /* Get settings. */
-#define ETHTOOL_SSET 0x00000002 /* Set settings. */
+#define ETHTOOL_GSET 0x00000001 /* DEPRECATED, Get settings.
+ * Please use ETHTOOL_GLINKSETTINGS
+ */
+#define ETHTOOL_SSET 0x00000002 /* DEPRECATED, Set settings.
+ * Please use ETHTOOL_SLINKSETTINGS
+ */
#define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */
#define ETHTOOL_GREGS 0x00000004 /* Get NIC registers. */
#define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */
#define ETHTOOL_STUNABLE 0x00000049 /* Set tunable configuration */
#define ETHTOOL_GPHYSTATS 0x0000004a /* get PHY-specific statistics */
+#define ETHTOOL_PERQUEUE 0x0000004b /* Set per queue options */
+
+#define ETHTOOL_GLINKSETTINGS 0x0000004c /* Get ethtool_link_settings */
+#define ETHTOOL_SLINKSETTINGS 0x0000004d /* Set ethtool_link_settings */
+
+
/* compatibility with older code */
#define SPARC_ETH_GSET ETHTOOL_GSET
#define SPARC_ETH_SSET ETHTOOL_SSET
-#define SUPPORTED_10baseT_Half (1 << 0)
-#define SUPPORTED_10baseT_Full (1 << 1)
-#define SUPPORTED_100baseT_Half (1 << 2)
-#define SUPPORTED_100baseT_Full (1 << 3)
-#define SUPPORTED_1000baseT_Half (1 << 4)
-#define SUPPORTED_1000baseT_Full (1 << 5)
-#define SUPPORTED_Autoneg (1 << 6)
-#define SUPPORTED_TP (1 << 7)
-#define SUPPORTED_AUI (1 << 8)
-#define SUPPORTED_MII (1 << 9)
-#define SUPPORTED_FIBRE (1 << 10)
-#define SUPPORTED_BNC (1 << 11)
-#define SUPPORTED_10000baseT_Full (1 << 12)
-#define SUPPORTED_Pause (1 << 13)
-#define SUPPORTED_Asym_Pause (1 << 14)
-#define SUPPORTED_2500baseX_Full (1 << 15)
-#define SUPPORTED_Backplane (1 << 16)
-#define SUPPORTED_1000baseKX_Full (1 << 17)
-#define SUPPORTED_10000baseKX4_Full (1 << 18)
-#define SUPPORTED_10000baseKR_Full (1 << 19)
-#define SUPPORTED_10000baseR_FEC (1 << 20)
-#define SUPPORTED_20000baseMLD2_Full (1 << 21)
-#define SUPPORTED_20000baseKR2_Full (1 << 22)
-#define SUPPORTED_40000baseKR4_Full (1 << 23)
-#define SUPPORTED_40000baseCR4_Full (1 << 24)
-#define SUPPORTED_40000baseSR4_Full (1 << 25)
-#define SUPPORTED_40000baseLR4_Full (1 << 26)
-#define SUPPORTED_56000baseKR4_Full (1 << 27)
-#define SUPPORTED_56000baseCR4_Full (1 << 28)
-#define SUPPORTED_56000baseSR4_Full (1 << 29)
-#define SUPPORTED_56000baseLR4_Full (1 << 30)
-
-#define ADVERTISED_10baseT_Half (1 << 0)
-#define ADVERTISED_10baseT_Full (1 << 1)
-#define ADVERTISED_100baseT_Half (1 << 2)
-#define ADVERTISED_100baseT_Full (1 << 3)
-#define ADVERTISED_1000baseT_Half (1 << 4)
-#define ADVERTISED_1000baseT_Full (1 << 5)
-#define ADVERTISED_Autoneg (1 << 6)
-#define ADVERTISED_TP (1 << 7)
-#define ADVERTISED_AUI (1 << 8)
-#define ADVERTISED_MII (1 << 9)
-#define ADVERTISED_FIBRE (1 << 10)
-#define ADVERTISED_BNC (1 << 11)
-#define ADVERTISED_10000baseT_Full (1 << 12)
-#define ADVERTISED_Pause (1 << 13)
-#define ADVERTISED_Asym_Pause (1 << 14)
-#define ADVERTISED_2500baseX_Full (1 << 15)
-#define ADVERTISED_Backplane (1 << 16)
-#define ADVERTISED_1000baseKX_Full (1 << 17)
-#define ADVERTISED_10000baseKX4_Full (1 << 18)
-#define ADVERTISED_10000baseKR_Full (1 << 19)
-#define ADVERTISED_10000baseR_FEC (1 << 20)
-#define ADVERTISED_20000baseMLD2_Full (1 << 21)
-#define ADVERTISED_20000baseKR2_Full (1 << 22)
-#define ADVERTISED_40000baseKR4_Full (1 << 23)
-#define ADVERTISED_40000baseCR4_Full (1 << 24)
-#define ADVERTISED_40000baseSR4_Full (1 << 25)
-#define ADVERTISED_40000baseLR4_Full (1 << 26)
-#define ADVERTISED_56000baseKR4_Full (1 << 27)
-#define ADVERTISED_56000baseCR4_Full (1 << 28)
-#define ADVERTISED_56000baseSR4_Full (1 << 29)
-#define ADVERTISED_56000baseLR4_Full (1 << 30)
+/* Link mode bit indices */
+enum ethtool_link_mode_bit_indices {
+ ETHTOOL_LINK_MODE_10baseT_Half_BIT = 0,
+ ETHTOOL_LINK_MODE_10baseT_Full_BIT = 1,
+ ETHTOOL_LINK_MODE_100baseT_Half_BIT = 2,
+ ETHTOOL_LINK_MODE_100baseT_Full_BIT = 3,
+ ETHTOOL_LINK_MODE_1000baseT_Half_BIT = 4,
+ ETHTOOL_LINK_MODE_1000baseT_Full_BIT = 5,
+ ETHTOOL_LINK_MODE_Autoneg_BIT = 6,
+ ETHTOOL_LINK_MODE_TP_BIT = 7,
+ ETHTOOL_LINK_MODE_AUI_BIT = 8,
+ ETHTOOL_LINK_MODE_MII_BIT = 9,
+ ETHTOOL_LINK_MODE_FIBRE_BIT = 10,
+ ETHTOOL_LINK_MODE_BNC_BIT = 11,
+ ETHTOOL_LINK_MODE_10000baseT_Full_BIT = 12,
+ ETHTOOL_LINK_MODE_Pause_BIT = 13,
+ ETHTOOL_LINK_MODE_Asym_Pause_BIT = 14,
+ ETHTOOL_LINK_MODE_2500baseX_Full_BIT = 15,
+ ETHTOOL_LINK_MODE_Backplane_BIT = 16,
+ ETHTOOL_LINK_MODE_1000baseKX_Full_BIT = 17,
+ ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT = 18,
+ ETHTOOL_LINK_MODE_10000baseKR_Full_BIT = 19,
+ ETHTOOL_LINK_MODE_10000baseR_FEC_BIT = 20,
+ ETHTOOL_LINK_MODE_20000baseMLD2_Full_BIT = 21,
+ ETHTOOL_LINK_MODE_20000baseKR2_Full_BIT = 22,
+ ETHTOOL_LINK_MODE_40000baseKR4_Full_BIT = 23,
+ ETHTOOL_LINK_MODE_40000baseCR4_Full_BIT = 24,
+ ETHTOOL_LINK_MODE_40000baseSR4_Full_BIT = 25,
+ ETHTOOL_LINK_MODE_40000baseLR4_Full_BIT = 26,
+ ETHTOOL_LINK_MODE_56000baseKR4_Full_BIT = 27,
+ ETHTOOL_LINK_MODE_56000baseCR4_Full_BIT = 28,
+ ETHTOOL_LINK_MODE_56000baseSR4_Full_BIT = 29,
+ ETHTOOL_LINK_MODE_56000baseLR4_Full_BIT = 30,
+
+ /* Last allowed bit for __ETHTOOL_LINK_MODE_LEGACY_MASK is bit
+ * 31. Please do NOT define any SUPPORTED_* or ADVERTISED_*
+ * macro for bits > 31. The only way to use indices > 31 is to
+ * use the new ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API.
+ */
+
+ __ETHTOOL_LINK_MODE_LAST
+ = ETHTOOL_LINK_MODE_56000baseLR4_Full_BIT,
+};
+
+#define __ETHTOOL_LINK_MODE_LEGACY_MASK(base_name) \
+ (1UL << (ETHTOOL_LINK_MODE_ ## base_name ## _BIT))
+
+/* DEPRECATED macros. Please migrate to
+ * ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. Please do NOT
+ * define any new SUPPORTED_* macro for bits > 31.
+ */
+#define SUPPORTED_10baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Half)
+#define SUPPORTED_10baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Full)
+#define SUPPORTED_100baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Half)
+#define SUPPORTED_100baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Full)
+#define SUPPORTED_1000baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Half)
+#define SUPPORTED_1000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Full)
+#define SUPPORTED_Autoneg __ETHTOOL_LINK_MODE_LEGACY_MASK(Autoneg)
+#define SUPPORTED_TP __ETHTOOL_LINK_MODE_LEGACY_MASK(TP)
+#define SUPPORTED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI)
+#define SUPPORTED_MII __ETHTOOL_LINK_MODE_LEGACY_MASK(MII)
+#define SUPPORTED_FIBRE __ETHTOOL_LINK_MODE_LEGACY_MASK(FIBRE)
+#define SUPPORTED_BNC __ETHTOOL_LINK_MODE_LEGACY_MASK(BNC)
+#define SUPPORTED_10000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseT_Full)
+#define SUPPORTED_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Pause)
+#define SUPPORTED_Asym_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Asym_Pause)
+#define SUPPORTED_2500baseX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(2500baseX_Full)
+#define SUPPORTED_Backplane __ETHTOOL_LINK_MODE_LEGACY_MASK(Backplane)
+#define SUPPORTED_1000baseKX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseKX_Full)
+#define SUPPORTED_10000baseKX4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKX4_Full)
+#define SUPPORTED_10000baseKR_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKR_Full)
+#define SUPPORTED_10000baseR_FEC __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseR_FEC)
+#define SUPPORTED_20000baseMLD2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseMLD2_Full)
+#define SUPPORTED_20000baseKR2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseKR2_Full)
+#define SUPPORTED_40000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseKR4_Full)
+#define SUPPORTED_40000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseCR4_Full)
+#define SUPPORTED_40000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseSR4_Full)
+#define SUPPORTED_40000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseLR4_Full)
+#define SUPPORTED_56000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseKR4_Full)
+#define SUPPORTED_56000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseCR4_Full)
+#define SUPPORTED_56000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseSR4_Full)
+#define SUPPORTED_56000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseLR4_Full)
+/* Please do not define any new SUPPORTED_* macro for bits > 31, see
+ * notice above.
+ */
+
+/*
+ * DEPRECATED macros. Please migrate to
+ * ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. Please do NOT
+ * define any new ADERTISE_* macro for bits > 31.
+ */
+#define ADVERTISED_10baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Half)
+#define ADVERTISED_10baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Full)
+#define ADVERTISED_100baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Half)
+#define ADVERTISED_100baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Full)
+#define ADVERTISED_1000baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Half)
+#define ADVERTISED_1000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Full)
+#define ADVERTISED_Autoneg __ETHTOOL_LINK_MODE_LEGACY_MASK(Autoneg)
+#define ADVERTISED_TP __ETHTOOL_LINK_MODE_LEGACY_MASK(TP)
+#define ADVERTISED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI)
+#define ADVERTISED_MII __ETHTOOL_LINK_MODE_LEGACY_MASK(MII)
+#define ADVERTISED_FIBRE __ETHTOOL_LINK_MODE_LEGACY_MASK(FIBRE)
+#define ADVERTISED_BNC __ETHTOOL_LINK_MODE_LEGACY_MASK(BNC)
+#define ADVERTISED_10000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseT_Full)
+#define ADVERTISED_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Pause)
+#define ADVERTISED_Asym_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Asym_Pause)
+#define ADVERTISED_2500baseX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(2500baseX_Full)
+#define ADVERTISED_Backplane __ETHTOOL_LINK_MODE_LEGACY_MASK(Backplane)
+#define ADVERTISED_1000baseKX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseKX_Full)
+#define ADVERTISED_10000baseKX4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKX4_Full)
+#define ADVERTISED_10000baseKR_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKR_Full)
+#define ADVERTISED_10000baseR_FEC __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseR_FEC)
+#define ADVERTISED_20000baseMLD2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseMLD2_Full)
+#define ADVERTISED_20000baseKR2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseKR2_Full)
+#define ADVERTISED_40000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseKR4_Full)
+#define ADVERTISED_40000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseCR4_Full)
+#define ADVERTISED_40000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseSR4_Full)
+#define ADVERTISED_40000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseLR4_Full)
+#define ADVERTISED_56000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseKR4_Full)
+#define ADVERTISED_56000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseCR4_Full)
+#define ADVERTISED_56000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseSR4_Full)
+#define ADVERTISED_56000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseLR4_Full)
+/* Please do not define any new ADVERTISED_* macro for bits > 31, see
+ * notice above.
+ */
/* The following are all involved in forcing a particular link
* mode for the device for setting things. When getting the
* it was forced up into this mode or autonegotiated.
*/
-/* The forced speed, 10Mb, 100Mb, gigabit, [2.5|5|10|20|25|40|50|56|100]GbE. */
+/* The forced speed, in units of 1Mb. All values 0 to INT_MAX are legal. */
#define SPEED_10 10
#define SPEED_100 100
#define SPEED_1000 1000
#define SPEED_UNKNOWN -1
+static inline int ethtool_validate_speed(__u32 speed)
+{
+ return speed <= INT_MAX || speed == SPEED_UNKNOWN;
+}
+
/* Duplex, half or full. */
#define DUPLEX_HALF 0x00
#define DUPLEX_FULL 0x01
#define DUPLEX_UNKNOWN 0xff
+static inline int ethtool_validate_duplex(__u8 duplex)
+{
+ switch (duplex) {
+ case DUPLEX_HALF:
+ case DUPLEX_FULL:
+ case DUPLEX_UNKNOWN:
+ return 1;
+ }
+
+ return 0;
+}
+
/* Which connector port. */
#define PORT_TP 0x00
#define PORT_AUI 0x01
#define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */
#define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */
#define AH_ESP_V4_FLOW 0x04 /* hash only */
-#define TCP_V6_FLOW 0x05 /* hash only */
-#define UDP_V6_FLOW 0x06 /* hash only */
-#define SCTP_V6_FLOW 0x07 /* hash only */
+#define TCP_V6_FLOW 0x05 /* hash or spec (tcp_ip6_spec; nfc only) */
+#define UDP_V6_FLOW 0x06 /* hash or spec (udp_ip6_spec; nfc only) */
+#define SCTP_V6_FLOW 0x07 /* hash or spec (sctp_ip6_spec; nfc only) */
#define AH_ESP_V6_FLOW 0x08 /* hash only */
#define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */
#define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */
-#define AH_V6_FLOW 0x0b /* hash only */
-#define ESP_V6_FLOW 0x0c /* hash only */
-#define IP_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */
+#define AH_V6_FLOW 0x0b /* hash or spec (ah_ip6_spec; nfc only) */
+#define ESP_V6_FLOW 0x0c /* hash or spec (esp_ip6_spec; nfc only) */
+#define IPV4_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */
+#define IP_USER_FLOW IPV4_USER_FLOW
+#define IPV6_USER_FLOW 0x0e /* spec only (usr_ip6_spec; nfc only) */
#define IPV4_FLOW 0x10 /* hash only */
#define IPV6_FLOW 0x11 /* hash only */
#define ETHER_FLOW 0x12 /* spec only (ether_spec) */
};
#define ETH_RESET_SHARED_SHIFT 16
+
+/**
+ * struct ethtool_link_settings - link control and status
+ *
+ * IMPORTANT, Backward compatibility notice: When implementing new
+ * user-space tools, please first try %ETHTOOL_GLINKSETTINGS, and
+ * if it succeeds use %ETHTOOL_SLINKSETTINGS to change link
+ * settings; do not use %ETHTOOL_SSET if %ETHTOOL_GLINKSETTINGS
+ * succeeded: stick to %ETHTOOL_GLINKSETTINGS/%SLINKSETTINGS in
+ * that case. Conversely, if %ETHTOOL_GLINKSETTINGS fails, use
+ * %ETHTOOL_GSET to query and %ETHTOOL_SSET to change link
+ * settings; do not use %ETHTOOL_SLINKSETTINGS if
+ * %ETHTOOL_GLINKSETTINGS failed: stick to
+ * %ETHTOOL_GSET/%ETHTOOL_SSET in that case.
+ *
+ * @cmd: Command number = %ETHTOOL_GLINKSETTINGS or %ETHTOOL_SLINKSETTINGS
+ * @speed: Link speed (Mbps)
+ * @duplex: Duplex mode; one of %DUPLEX_*
+ * @port: Physical connector type; one of %PORT_*
+ * @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not
+ * applicable. For clause 45 PHYs this is the PRTAD.
+ * @autoneg: Enable/disable autonegotiation and auto-detection;
+ * either %AUTONEG_DISABLE or %AUTONEG_ENABLE
+ * @mdio_support: Bitmask of %ETH_MDIO_SUPPORTS_* flags for the MDIO
+ * protocols supported by the interface; 0 if unknown.
+ * Read-only.
+ * @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of
+ * %ETH_TP_MDI_*. If the status is unknown or not applicable, the
+ * value will be %ETH_TP_MDI_INVALID. Read-only.
+ * @eth_tp_mdix_ctrl: Ethernet twisted pair MDI(-X) control; one of
+ * %ETH_TP_MDI_*. If MDI(-X) control is not implemented, reads
+ * yield %ETH_TP_MDI_INVALID and writes may be ignored or rejected.
+ * When written successfully, the link should be renegotiated if
+ * necessary.
+ * @link_mode_masks_nwords: Number of 32-bit words for each of the
+ * supported, advertising, lp_advertising link mode bitmaps. For
+ * %ETHTOOL_GLINKSETTINGS: on entry, number of words passed by user
+ * (>= 0); on return, if handshake in progress, negative if
+ * request size unsupported by kernel: absolute value indicates
+ * kernel expected size and all the other fields but cmd
+ * are 0; otherwise (handshake completed), strictly positive
+ * to indicate size used by kernel and cmd field stays
+ * %ETHTOOL_GLINKSETTINGS, all other fields populated by driver. For
+ * %ETHTOOL_SLINKSETTINGS: must be valid on entry, ie. a positive
+ * value returned previously by %ETHTOOL_GLINKSETTINGS, otherwise
+ * refused. For drivers: ignore this field (use kernel's
+ * __ETHTOOL_LINK_MODE_MASK_NBITS instead), any change to it will
+ * be overwritten by kernel.
+ * @supported: Bitmap with each bit meaning given by
+ * %ethtool_link_mode_bit_indices for the link modes, physical
+ * connectors and other link features for which the interface
+ * supports autonegotiation or auto-detection. Read-only.
+ * @advertising: Bitmap with each bit meaning given by
+ * %ethtool_link_mode_bit_indices for the link modes, physical
+ * connectors and other link features that are advertised through
+ * autonegotiation or enabled for auto-detection.
+ * @lp_advertising: Bitmap with each bit meaning given by
+ * %ethtool_link_mode_bit_indices for the link modes, and other
+ * link features that the link partner advertised through
+ * autonegotiation; 0 if unknown or not applicable. Read-only.
+ *
+ * If autonegotiation is disabled, the speed and @duplex represent the
+ * fixed link mode and are writable if the driver supports multiple
+ * link modes. If it is enabled then they are read-only; if the link
+ * is up they represent the negotiated link mode; if the link is down,
+ * the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and
+ * @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode.
+ *
+ * Some hardware interfaces may have multiple PHYs and/or physical
+ * connectors fitted or do not allow the driver to detect which are
+ * fitted. For these interfaces @port and/or @phy_address may be
+ * writable, possibly dependent on @autoneg being %AUTONEG_DISABLE.
+ * Otherwise, attempts to write different values may be ignored or
+ * rejected.
+ *
+ * Deprecated %ethtool_cmd fields transceiver, maxtxpkt and maxrxpkt
+ * are not available in %ethtool_link_settings. Until all drivers are
+ * converted to ignore them or to the new %ethtool_link_settings API,
+ * for both queries and changes, users should always try
+ * %ETHTOOL_GLINKSETTINGS first, and if it fails with -ENOTSUPP stick
+ * only to %ETHTOOL_GSET and %ETHTOOL_SSET consistently. If it
+ * succeeds, then users should stick to %ETHTOOL_GLINKSETTINGS and
+ * %ETHTOOL_SLINKSETTINGS (which would support drivers implementing
+ * either %ethtool_cmd or %ethtool_link_settings).
+ *
+ * Users should assume that all fields not marked read-only are
+ * writable and subject to validation by the driver. They should use
+ * %ETHTOOL_GLINKSETTINGS to get the current values before making specific
+ * changes and then applying them with %ETHTOOL_SLINKSETTINGS.
+ *
+ * Drivers that implement %get_link_ksettings and/or
+ * %set_link_ksettings should ignore the @cmd
+ * and @link_mode_masks_nwords fields (any change to them overwritten
+ * by kernel), and rely only on kernel's internal
+ * %__ETHTOOL_LINK_MODE_MASK_NBITS and
+ * %ethtool_link_mode_mask_t. Drivers that implement
+ * %set_link_ksettings() should validate all fields other than @cmd
+ * and @link_mode_masks_nwords that are not described as read-only or
+ * deprecated, and must ignore all fields described as read-only.
+ */
+struct ethtool_link_settings {
+ __u32 cmd;
+ __u32 speed;
+ __u8 duplex;
+ __u8 port;
+ __u8 phy_address;
+ __u8 autoneg;
+ __u8 mdio_support;
+ __u8 eth_tp_mdix;
+ __u8 eth_tp_mdix_ctrl;
+ __s8 link_mode_masks_nwords;
+ __u32 reserved[8];
+ __u32 link_mode_masks[0];
+ /* layout of link_mode_masks fields:
+ * __u32 map_supported[link_mode_masks_nwords];
+ * __u32 map_advertising[link_mode_masks_nwords];
+ * __u32 map_lp_advertising[link_mode_masks_nwords];
+ */
+};
#endif /* _UAPI_LINUX_ETHTOOL_H */
projects / linux-2.6-block.git / blobdiff