*
* @NL80211_CMD_GET_SCAN: get scan results
* @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters
+ * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
+ * probe requests at CCK rate or not.
* @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to
* NL80211_CMD_GET_SCAN and on the "scan" multicast group)
* @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
* specified using %NL80211_ATTR_DURATION. When called, this operation
* returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the
* TX status event pertaining to the TX request.
+ * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
+ * management frames at CCK rate or not in 2GHz band.
* @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
* command may be used with the corresponding cookie to cancel the wait
* time if it is known that it is no longer necessary.
* this command may also be sent by the driver as an MLME event to
* inform userspace of the new replay counter.
*
+ * @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace
+ * of PMKSA caching dandidates.
+ *
+ * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
+ * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame.
+ *
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
NL80211_CMD_SET_REKEY_OFFLOAD,
+ NL80211_CMD_PMKSA_CANDIDATE,
+
+ NL80211_CMD_TDLS_OPER,
+ NL80211_CMD_TDLS_MGMT,
+
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
* @NL80211_ATTR_ROAM_SUPPORT: Indicates whether the firmware is capable of
* roaming to another AP in the same ESS if the signal lever is low.
*
+ * @NL80211_ATTR_PMKSA_CANDIDATE: Nested attribute containing the PMKSA caching
+ * candidate information, see &enum nl80211_pmksa_candidate_attr.
+ *
+ * @NL80211_ATTR_TX_NO_CCK_RATE: Indicates whether to use CCK rate or not
+ * for management frames transmission. In order to avoid p2p probe/action
+ * frames are being transmitted at CCK rate in 2GHz band, the user space
+ * applications use this attribute.
+ * This attribute is used with %NL80211_CMD_TRIGGER_SCAN and
+ * %NL80211_CMD_FRAME commands.
+ *
+ * @NL80211_ATTR_TDLS_ACTION: Low level TDLS action code (e.g. link setup
+ * request, link setup confirm, link teardown, etc.). Values are
+ * described in the TDLS (802.11z) specification.
+ * @NL80211_ATTR_TDLS_DIALOG_TOKEN: Non-zero token for uniquely identifying a
+ * TDLS conversation between two devices.
+ * @NL80211_ATTR_TDLS_OPERATION: High level TDLS operation; see
+ * &enum nl80211_tdls_operation, represented as a u8.
+ * @NL80211_ATTR_TDLS_SUPPORT: A flag indicating the device can operate
+ * as a TDLS peer sta.
+ * @NL80211_ATTR_TDLS_EXTERNAL_SETUP: The TDLS discovery/setup and teardown
+ * procedures should be performed by sending TDLS packets via
+ * %NL80211_CMD_TDLS_MGMT. Otherwise %NL80211_CMD_TDLS_OPER should be
+ * used for asking the driver to perform a TDLS operation.
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
NL80211_ATTR_SCHED_SCAN_MATCH,
NL80211_ATTR_MAX_MATCH_SETS,
+ NL80211_ATTR_PMKSA_CANDIDATE,
+
+ NL80211_ATTR_TX_NO_CCK_RATE,
+
+ NL80211_ATTR_TDLS_ACTION,
+ NL80211_ATTR_TDLS_DIALOG_TOKEN,
+ NL80211_ATTR_TDLS_OPERATION,
+ NL80211_ATTR_TDLS_SUPPORT,
+ NL80211_ATTR_TDLS_EXTERNAL_SETUP,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
* @NL80211_STA_FLAG_WME: station is WME/QoS capable
* @NL80211_STA_FLAG_MFP: station uses management frame protection
* @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated
+ * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer
* @NL80211_STA_FLAG_MAX: highest station flag number currently defined
* @__NL80211_STA_FLAG_AFTER_LAST: internal use
*/
NL80211_STA_FLAG_WME,
NL80211_STA_FLAG_MFP,
NL80211_STA_FLAG_AUTHENTICATED,
+ NL80211_STA_FLAG_TDLS_PEER,
/* keep last */
__NL80211_STA_FLAG_AFTER_LAST,
* @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute
* containing info as possible, see &enum nl80211_sta_bss_param
* @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected
+ * @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update.
* @__NL80211_STA_INFO_AFTER_LAST: internal
* @NL80211_STA_INFO_MAX: highest possible station info attribute
*/
NL80211_STA_INFO_RX_BITRATE,
NL80211_STA_INFO_BSS_PARAM,
NL80211_STA_INFO_CONNECTED_TIME,
+ NL80211_STA_INFO_STA_FLAGS,
/* keep last */
__NL80211_STA_INFO_AFTER_LAST,
NL80211_STA_WME_MAX = __NL80211_STA_WME_AFTER_LAST - 1
};
+/**
+ * enum nl80211_pmksa_candidate_attr - attributes for PMKSA caching candidates
+ * @__NL80211_PMKSA_CANDIDATE_INVALID: invalid number for nested attributes
+ * @NL80211_PMKSA_CANDIDATE_INDEX: candidate index (u32; the smaller, the higher
+ * priority)
+ * @NL80211_PMKSA_CANDIDATE_BSSID: candidate BSSID (6 octets)
+ * @NL80211_PMKSA_CANDIDATE_PREAUTH: RSN pre-authentication supported (flag)
+ * @NUM_NL80211_PMKSA_CANDIDATE: number of PMKSA caching candidate attributes
+ * (internal)
+ * @MAX_NL80211_PMKSA_CANDIDATE: highest PMKSA caching candidate attribute
+ * (internal)
+ */
+enum nl80211_pmksa_candidate_attr {
+ __NL80211_PMKSA_CANDIDATE_INVALID,
+ NL80211_PMKSA_CANDIDATE_INDEX,
+ NL80211_PMKSA_CANDIDATE_BSSID,
+ NL80211_PMKSA_CANDIDATE_PREAUTH,
+
+ /* keep last */
+ NUM_NL80211_PMKSA_CANDIDATE,
+ MAX_NL80211_PMKSA_CANDIDATE = NUM_NL80211_PMKSA_CANDIDATE - 1
+};
+
+/**
+ * enum nl80211_tdls_operation - values for %NL80211_ATTR_TDLS_OPERATION
+ * @NL80211_TDLS_DISCOVERY_REQ: Send a TDLS discovery request
+ * @NL80211_TDLS_SETUP: Setup TDLS link
+ * @NL80211_TDLS_TEARDOWN: Teardown a TDLS link which is already established
+ * @NL80211_TDLS_ENABLE_LINK: Enable TDLS link
+ * @NL80211_TDLS_DISABLE_LINK: Disable TDLS link
+ */
+enum nl80211_tdls_operation {
+ NL80211_TDLS_DISCOVERY_REQ,
+ NL80211_TDLS_SETUP,
+ NL80211_TDLS_TEARDOWN,
+ NL80211_TDLS_ENABLE_LINK,
+ NL80211_TDLS_DISABLE_LINK,
+};
+
#endif /* __LINUX_NL80211_H */
projects / linux-2.6-block.git / blobdiff