+++ /dev/null
-/*
- * Copyright (c) 1997-1998 Mark Lord
- * Copyright (c) 2007 MontaVista Software, Inc. <source@mvista.com>
- *
- * May be copied or modified under the terms of the GNU General Public License
- *
- * June 22, 2004 - get rid of check_region
- * - Jesper Juhl
- *
- */
-
-/*
- * This module provides support for the bus-master IDE DMA function
- * of the Tekram TRM290 chip, used on a variety of PCI IDE add-on boards,
- * including a "Precision Instruments" board. The TRM290 pre-dates
- * the sff-8038 standard (ide-dma.c) by a few months, and differs
- * significantly enough to warrant separate routines for some functions,
- * while re-using others from ide-dma.c.
- *
- * EXPERIMENTAL! It works for me (a sample of one).
- *
- * Works reliably for me in DMA mode (READs only),
- * DMA WRITEs are disabled by default (see #define below);
- *
- * DMA is not enabled automatically for this chipset,
- * but can be turned on manually (with "hdparm -d1") at run time.
- *
- * I need volunteers with "spare" drives for further testing
- * and development, and maybe to help figure out the peculiarities.
- * Even knowing the registers (below), some things behave strangely.
- */
-
-#define TRM290_NO_DMA_WRITES /* DMA writes seem unreliable sometimes */
-
-/*
- * TRM-290 PCI-IDE2 Bus Master Chip
- * ================================
- * The configuration registers are addressed in normal I/O port space
- * and are used as follows:
- *
- * trm290_base depends on jumper settings, and is probed for by ide-dma.c
- *
- * trm290_base+2 when WRITTEN: chiptest register (byte, write-only)
- * bit7 must always be written as "1"
- * bits6-2 undefined
- * bit1 1=legacy_compatible_mode, 0=native_pci_mode
- * bit0 1=test_mode, 0=normal(default)
- *
- * trm290_base+2 when READ: status register (byte, read-only)
- * bits7-2 undefined
- * bit1 channel0 busmaster interrupt status 0=none, 1=asserted
- * bit0 channel0 interrupt status 0=none, 1=asserted
- *
- * trm290_base+3 Interrupt mask register
- * bits7-5 undefined
- * bit4 legacy_header: 1=present, 0=absent
- * bit3 channel1 busmaster interrupt status 0=none, 1=asserted (read only)
- * bit2 channel1 interrupt status 0=none, 1=asserted (read only)
- * bit1 channel1 interrupt mask: 1=masked, 0=unmasked(default)
- * bit0 channel0 interrupt mask: 1=masked, 0=unmasked(default)
- *
- * trm290_base+1 "CPR" Config Pointer Register (byte)
- * bit7 1=autoincrement CPR bits 2-0 after each access of CDR
- * bit6 1=min. 1 wait-state posted write cycle (default), 0=0 wait-state
- * bit5 0=enabled master burst access (default), 1=disable (write only)
- * bit4 PCI DEVSEL# timing select: 1=medium(default), 0=fast
- * bit3 0=primary IDE channel, 1=secondary IDE channel
- * bits2-0 register index for accesses through CDR port
- *
- * trm290_base+0 "CDR" Config Data Register (word)
- * two sets of seven config registers,
- * selected by CPR bit 3 (channel) and CPR bits 2-0 (index 0 to 6),
- * each index defined below:
- *
- * Index-0 Base address register for command block (word)
- * defaults: 0x1f0 for primary, 0x170 for secondary
- *
- * Index-1 general config register (byte)
- * bit7 1=DMA enable, 0=DMA disable
- * bit6 1=activate IDE_RESET, 0=no action (default)
- * bit5 1=enable IORDY, 0=disable IORDY (default)
- * bit4 0=16-bit data port(default), 1=8-bit (XT) data port
- * bit3 interrupt polarity: 1=active_low, 0=active_high(default)
- * bit2 power-saving-mode(?): 1=enable, 0=disable(default) (write only)
- * bit1 bus_master_mode(?): 1=enable, 0=disable(default)
- * bit0 enable_io_ports: 1=enable(default), 0=disable
- *
- * Index-2 read-ahead counter preload bits 0-7 (byte, write only)
- * bits7-0 bits7-0 of readahead count
- *
- * Index-3 read-ahead config register (byte, write only)
- * bit7 1=enable_readahead, 0=disable_readahead(default)
- * bit6 1=clear_FIFO, 0=no_action
- * bit5 undefined
- * bit4 mode4 timing control: 1=enable, 0=disable(default)
- * bit3 undefined
- * bit2 undefined
- * bits1-0 bits9-8 of read-ahead count
- *
- * Index-4 base address register for control block (word)
- * defaults: 0x3f6 for primary, 0x376 for secondary
- *
- * Index-5 data port timings (shared by both drives) (byte)
- * standard PCI "clk" (clock) counts, default value = 0xf5
- *
- * bits7-6 setup time: 00=1clk, 01=2clk, 10=3clk, 11=4clk
- * bits5-3 hold time: 000=1clk, 001=2clk, 010=3clk,
- * 011=4clk, 100=5clk, 101=6clk,
- * 110=8clk, 111=12clk
- * bits2-0 active time: 000=2clk, 001=3clk, 010=4clk,
- * 011=5clk, 100=6clk, 101=8clk,
- * 110=12clk, 111=16clk
- *
- * Index-6 command/control port timings (shared by both drives) (byte)
- * same layout as Index-5, default value = 0xde
- *
- * Suggested CDR programming for PIO mode0 (600ns):
- * 0x01f0,0x21,0xff,0x80,0x03f6,0xf5,0xde ; primary
- * 0x0170,0x21,0xff,0x80,0x0376,0xf5,0xde ; secondary
- *
- * Suggested CDR programming for PIO mode3 (180ns):
- * 0x01f0,0x21,0xff,0x80,0x03f6,0x09,0xde ; primary
- * 0x0170,0x21,0xff,0x80,0x0376,0x09,0xde ; secondary
- *
- * Suggested CDR programming for PIO mode4 (120ns):
- * 0x01f0,0x21,0xff,0x80,0x03f6,0x00,0xde ; primary
- * 0x0170,0x21,0xff,0x80,0x0376,0x00,0xde ; secondary
- *
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/ioport.h>
-#include <linux/interrupt.h>
-#include <linux/blkdev.h>
-#include <linux/init.h>
-#include <linux/pci.h>
-#include <linux/ide.h>
-
-#include <asm/io.h>
-
-#define DRV_NAME "trm290"
-
-static void trm290_prepare_drive (ide_drive_t *drive, unsigned int use_dma)
-{
- ide_hwif_t *hwif = drive->hwif;
- u16 reg = 0;
- unsigned long flags;
-
- /* select PIO or DMA */
- reg = use_dma ? (0x21 | 0x82) : (0x21 & ~0x82);
-
- local_irq_save(flags);
-
- if (reg != hwif->select_data) {
- hwif->select_data = reg;
- /* set PIO/DMA */
- outb(0x51 | (hwif->channel << 3), hwif->config_data + 1);
- outw(reg & 0xff, hwif->config_data);
- }
-
- /* enable IRQ if not probing */
- if (drive->dev_flags & IDE_DFLAG_PRESENT) {
- reg = inw(hwif->config_data + 3);
- reg &= 0x13;
- reg &= ~(1 << hwif->channel);
- outw(reg, hwif->config_data + 3);
- }
-
- local_irq_restore(flags);
-}
-
-static void trm290_dev_select(ide_drive_t *drive)
-{
- trm290_prepare_drive(drive, !!(drive->dev_flags & IDE_DFLAG_USING_DMA));
-
- outb(drive->select | ATA_DEVICE_OBS, drive->hwif->io_ports.device_addr);
-}
-
-static int trm290_dma_check(ide_drive_t *drive, struct ide_cmd *cmd)
-{
- if (cmd->tf_flags & IDE_TFLAG_WRITE) {
-#ifdef TRM290_NO_DMA_WRITES
- /* always use PIO for writes */
- return 1;
-#endif
- }
- return 0;
-}
-
-static int trm290_dma_setup(ide_drive_t *drive, struct ide_cmd *cmd)
-{
- ide_hwif_t *hwif = drive->hwif;
- unsigned int count, rw = (cmd->tf_flags & IDE_TFLAG_WRITE) ? 1 : 2;
-
- count = ide_build_dmatable(drive, cmd);
- if (count == 0)
- /* try PIO instead of DMA */
- return 1;
-
- outl(hwif->dmatable_dma | rw, hwif->dma_base);
- /* start DMA */
- outw(count * 2 - 1, hwif->dma_base + 2);
-
- return 0;
-}
-
-static void trm290_dma_start(ide_drive_t *drive)
-{
- trm290_prepare_drive(drive, 1);
-}
-
-static int trm290_dma_end(ide_drive_t *drive)
-{
- u16 status = inw(drive->hwif->dma_base + 2);
-
- trm290_prepare_drive(drive, 0);
-
- return status != 0x00ff;
-}
-
-static int trm290_dma_test_irq(ide_drive_t *drive)
-{
- u16 status = inw(drive->hwif->dma_base + 2);
-
- return status == 0x00ff;
-}
-
-static void trm290_dma_host_set(ide_drive_t *drive, int on)
-{
-}
-
-static void init_hwif_trm290(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- unsigned int cfg_base = pci_resource_start(dev, 4);
- unsigned long flags;
- u8 reg = 0;
-
- if ((dev->class & 5) && cfg_base)
- printk(KERN_INFO DRV_NAME " %s: chip", pci_name(dev));
- else {
- cfg_base = 0x3df0;
- printk(KERN_INFO DRV_NAME " %s: using default", pci_name(dev));
- }
- printk(KERN_CONT " config base at 0x%04x\n", cfg_base);
- hwif->config_data = cfg_base;
- hwif->dma_base = (cfg_base + 4) ^ (hwif->channel ? 0x80 : 0);
-
- printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
- hwif->name, hwif->dma_base, hwif->dma_base + 3);
-
- if (ide_allocate_dma_engine(hwif))
- return;
-
- local_irq_save(flags);
- /* put config reg into first byte of hwif->select_data */
- outb(0x51 | (hwif->channel << 3), hwif->config_data + 1);
- /* select PIO as default */
- hwif->select_data = 0x21;
- outb(hwif->select_data, hwif->config_data);
- /* get IRQ info */
- reg = inb(hwif->config_data + 3);
- /* mask IRQs for both ports */
- reg = (reg & 0x10) | 0x03;
- outb(reg, hwif->config_data + 3);
- local_irq_restore(flags);
-
- if (reg & 0x10)
- /* legacy mode */
- hwif->irq = hwif->channel ? 15 : 14;
-
-#if 1
- {
- /*
- * My trm290-based card doesn't seem to work with all possible values
- * for the control basereg, so this kludge ensures that we use only
- * values that are known to work. Ugh. -ml
- */
- u16 new, old, compat = hwif->channel ? 0x374 : 0x3f4;
- static u16 next_offset = 0;
- u8 old_mask;
-
- outb(0x54 | (hwif->channel << 3), hwif->config_data + 1);
- old = inw(hwif->config_data);
- old &= ~1;
- old_mask = inb(old + 2);
- if (old != compat && old_mask == 0xff) {
- /* leave lower 10 bits untouched */
- compat += (next_offset += 0x400);
- hwif->io_ports.ctl_addr = compat + 2;
- outw(compat | 1, hwif->config_data);
- new = inw(hwif->config_data);
- printk(KERN_INFO "%s: control basereg workaround: "
- "old=0x%04x, new=0x%04x\n",
- hwif->name, old, new & ~1);
- }
- }
-#endif
-}
-
-static const struct ide_tp_ops trm290_tp_ops = {
- .exec_command = ide_exec_command,
- .read_status = ide_read_status,
- .read_altstatus = ide_read_altstatus,
- .write_devctl = ide_write_devctl,
-
- .dev_select = trm290_dev_select,
- .tf_load = ide_tf_load,
- .tf_read = ide_tf_read,
-
- .input_data = ide_input_data,
- .output_data = ide_output_data,
-};
-
-static const struct ide_dma_ops trm290_dma_ops = {
- .dma_host_set = trm290_dma_host_set,
- .dma_setup = trm290_dma_setup,
- .dma_start = trm290_dma_start,
- .dma_end = trm290_dma_end,
- .dma_test_irq = trm290_dma_test_irq,
- .dma_lost_irq = ide_dma_lost_irq,
- .dma_check = trm290_dma_check,
-};
-
-static const struct ide_port_info trm290_chipset = {
- .name = DRV_NAME,
- .init_hwif = init_hwif_trm290,
- .tp_ops = &trm290_tp_ops,
- .dma_ops = &trm290_dma_ops,
- .host_flags = IDE_HFLAG_TRM290 |
- IDE_HFLAG_NO_ATAPI_DMA |
-#if 0 /* play it safe for now */
- IDE_HFLAG_TRUST_BIOS_FOR_DMA |
-#endif
- IDE_HFLAG_NO_AUTODMA |
- IDE_HFLAG_NO_LBA48,
-};
-
-static int trm290_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
- return ide_pci_init_one(dev, &trm290_chipset, NULL);
-}
-
-static const struct pci_device_id trm290_pci_tbl[] = {
- { PCI_VDEVICE(TEKRAM, PCI_DEVICE_ID_TEKRAM_DC290), 0 },
- { 0, },
-};
-MODULE_DEVICE_TABLE(pci, trm290_pci_tbl);
-
-static struct pci_driver trm290_pci_driver = {
- .name = "TRM290_IDE",
- .id_table = trm290_pci_tbl,
- .probe = trm290_init_one,
- .remove = ide_pci_remove,
-};
-
-static int __init trm290_ide_init(void)
-{
- return ide_pci_register_driver(&trm290_pci_driver);
-}
-
-static void __exit trm290_ide_exit(void)
-{
- pci_unregister_driver(&trm290_pci_driver);
-}
-
-module_init(trm290_ide_init);
-module_exit(trm290_ide_exit);
-
-MODULE_AUTHOR("Mark Lord");
-MODULE_DESCRIPTION("PCI driver module for Tekram TRM290 IDE");
-MODULE_LICENSE("GPL");
projects / linux-2.6-block.git / blobdiff