+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines.
- * Due to massive hardware bugs, UltraDMA is only supported
- * on the 646U2 and not on the 646U.
- *
- * Copyright (C) 1998 Eddie C. Dost (ecd@skynet.be)
- * Copyright (C) 1998 David S. Miller (davem@redhat.com)
- *
- * Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
- * Copyright (C) 2007-2010 Bartlomiej Zolnierkiewicz
- * Copyright (C) 2007,2009 MontaVista Software, Inc. <source@mvista.com>
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-
-#define DRV_NAME "cmd64x"
-
-/*
- * CMD64x specific registers definition.
- */
-#define CFR 0x50
-#define CFR_INTR_CH0 0x04
-
-#define CMDTIM 0x52
-#define ARTTIM0 0x53
-#define DRWTIM0 0x54
-#define ARTTIM1 0x55
-#define DRWTIM1 0x56
-#define ARTTIM23 0x57
-#define ARTTIM23_DIS_RA2 0x04
-#define ARTTIM23_DIS_RA3 0x08
-#define ARTTIM23_INTR_CH1 0x10
-#define DRWTIM2 0x58
-#define BRST 0x59
-#define DRWTIM3 0x5b
-
-#define BMIDECR0 0x70
-#define MRDMODE 0x71
-#define MRDMODE_INTR_CH0 0x04
-#define MRDMODE_INTR_CH1 0x08
-#define UDIDETCR0 0x73
-#define DTPR0 0x74
-#define BMIDECR1 0x78
-#define BMIDECSR 0x79
-#define UDIDETCR1 0x7B
-#define DTPR1 0x7C
-
-static void cmd64x_program_timings(ide_drive_t *drive, u8 mode)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
- int bus_speed = ide_pci_clk ? ide_pci_clk : 33;
- const unsigned long T = 1000000 / bus_speed;
- static const u8 recovery_values[] =
- {15, 15, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0};
- static const u8 setup_values[] = {0x40, 0x40, 0x40, 0x80, 0, 0xc0};
- static const u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23};
- static const u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM2, DRWTIM3};
- struct ide_timing t;
- u8 arttim = 0;
-
- if (drive->dn >= ARRAY_SIZE(drwtim_regs))
- return;
-
- ide_timing_compute(drive, mode, &t, T, 0);
-
- /*
- * In case we've got too long recovery phase, try to lengthen
- * the active phase
- */
- if (t.recover > 16) {
- t.active += t.recover - 16;
- t.recover = 16;
- }
- if (t.active > 16) /* shouldn't actually happen... */
- t.active = 16;
-
- /*
- * Convert values to internal chipset representation
- */
- t.recover = recovery_values[t.recover];
- t.active &= 0x0f;
-
- /* Program the active/recovery counts into the DRWTIM register */
- pci_write_config_byte(dev, drwtim_regs[drive->dn],
- (t.active << 4) | t.recover);
-
- /*
- * The primary channel has individual address setup timing registers
- * for each drive and the hardware selects the slowest timing itself.
- * The secondary channel has one common register and we have to select
- * the slowest address setup timing ourselves.
- */
- if (hwif->channel) {
- ide_drive_t *pair = ide_get_pair_dev(drive);
-
- if (pair) {
- struct ide_timing tp;
-
- ide_timing_compute(pair, pair->pio_mode, &tp, T, 0);
- ide_timing_merge(&t, &tp, &t, IDE_TIMING_SETUP);
- if (pair->dma_mode) {
- ide_timing_compute(pair, pair->dma_mode,
- &tp, T, 0);
- ide_timing_merge(&tp, &t, &t, IDE_TIMING_SETUP);
- }
- }
- }
-
- if (t.setup > 5) /* shouldn't actually happen... */
- t.setup = 5;
-
- /*
- * Program the address setup clocks into the ARTTIM registers.
- * Avoid clearing the secondary channel's interrupt bit.
- */
- (void) pci_read_config_byte (dev, arttim_regs[drive->dn], &arttim);
- if (hwif->channel)
- arttim &= ~ARTTIM23_INTR_CH1;
- arttim &= ~0xc0;
- arttim |= setup_values[t.setup];
- (void) pci_write_config_byte(dev, arttim_regs[drive->dn], arttim);
-}
-
-/*
- * Attempts to set drive's PIO mode.
- * Special cases are 8: prefetch off, 9: prefetch on (both never worked)
- */
-
-static void cmd64x_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- const u8 pio = drive->pio_mode - XFER_PIO_0;
-
- /*
- * Filter out the prefetch control values
- * to prevent PIO5 from being programmed
- */
- if (pio == 8 || pio == 9)
- return;
-
- cmd64x_program_timings(drive, XFER_PIO_0 + pio);
-}
-
-static void cmd64x_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 unit = drive->dn & 0x01;
- u8 regU = 0, pciU = hwif->channel ? UDIDETCR1 : UDIDETCR0;
- const u8 speed = drive->dma_mode;
-
- pci_read_config_byte(dev, pciU, ®U);
- regU &= ~(unit ? 0xCA : 0x35);
-
- switch(speed) {
- case XFER_UDMA_5:
- regU |= unit ? 0x0A : 0x05;
- break;
- case XFER_UDMA_4:
- regU |= unit ? 0x4A : 0x15;
- break;
- case XFER_UDMA_3:
- regU |= unit ? 0x8A : 0x25;
- break;
- case XFER_UDMA_2:
- regU |= unit ? 0x42 : 0x11;
- break;
- case XFER_UDMA_1:
- regU |= unit ? 0x82 : 0x21;
- break;
- case XFER_UDMA_0:
- regU |= unit ? 0xC2 : 0x31;
- break;
- case XFER_MW_DMA_2:
- case XFER_MW_DMA_1:
- case XFER_MW_DMA_0:
- cmd64x_program_timings(drive, speed);
- break;
- }
-
- pci_write_config_byte(dev, pciU, regU);
-}
-
-static void cmd648_clear_irq(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- unsigned long base = pci_resource_start(dev, 4);
- u8 irq_mask = hwif->channel ? MRDMODE_INTR_CH1 :
- MRDMODE_INTR_CH0;
- u8 mrdmode = inb(base + 1);
-
- /* clear the interrupt bit */
- outb((mrdmode & ~(MRDMODE_INTR_CH0 | MRDMODE_INTR_CH1)) | irq_mask,
- base + 1);
-}
-
-static void cmd64x_clear_irq(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- int irq_reg = hwif->channel ? ARTTIM23 : CFR;
- u8 irq_mask = hwif->channel ? ARTTIM23_INTR_CH1 :
- CFR_INTR_CH0;
- u8 irq_stat = 0;
-
- (void) pci_read_config_byte(dev, irq_reg, &irq_stat);
- /* clear the interrupt bit */
- (void) pci_write_config_byte(dev, irq_reg, irq_stat | irq_mask);
-}
-
-static int cmd648_test_irq(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- unsigned long base = pci_resource_start(dev, 4);
- u8 irq_mask = hwif->channel ? MRDMODE_INTR_CH1 :
- MRDMODE_INTR_CH0;
- u8 mrdmode = inb(base + 1);
-
- pr_debug("%s: mrdmode: 0x%02x irq_mask: 0x%02x\n",
- hwif->name, mrdmode, irq_mask);
-
- return (mrdmode & irq_mask) ? 1 : 0;
-}
-
-static int cmd64x_test_irq(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- int irq_reg = hwif->channel ? ARTTIM23 : CFR;
- u8 irq_mask = hwif->channel ? ARTTIM23_INTR_CH1 :
- CFR_INTR_CH0;
- u8 irq_stat = 0;
-
- (void) pci_read_config_byte(dev, irq_reg, &irq_stat);
-
- pr_debug("%s: irq_stat: 0x%02x irq_mask: 0x%02x\n",
- hwif->name, irq_stat, irq_mask);
-
- return (irq_stat & irq_mask) ? 1 : 0;
-}
-
-/*
- * ASUS P55T2P4D with CMD646 chipset revision 0x01 requires the old
- * event order for DMA transfers.
- */
-
-static int cmd646_1_dma_end(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- u8 dma_stat = 0, dma_cmd = 0;
-
- /* get DMA status */
- dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
- /* read DMA command state */
- dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD);
- /* stop DMA */
- outb(dma_cmd & ~1, hwif->dma_base + ATA_DMA_CMD);
- /* clear the INTR & ERROR bits */
- outb(dma_stat | 6, hwif->dma_base + ATA_DMA_STATUS);
- /* verify good DMA status */
- return (dma_stat & 7) != 4;
-}
-
-static int init_chipset_cmd64x(struct pci_dev *dev)
-{
- u8 mrdmode = 0;
-
- /* Set a good latency timer and cache line size value. */
- (void) pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
- /* FIXME: pci_set_master() to ensure a good latency timer value */
-
- /*
- * Enable interrupts, select MEMORY READ LINE for reads.
- *
- * NOTE: although not mentioned in the PCI0646U specs,
- * bits 0-1 are write only and won't be read back as
- * set or not -- PCI0646U2 specs clarify this point.
- */
- (void) pci_read_config_byte (dev, MRDMODE, &mrdmode);
- mrdmode &= ~0x30;
- (void) pci_write_config_byte(dev, MRDMODE, (mrdmode | 0x02));
-
- return 0;
-}
-
-static u8 cmd64x_cable_detect(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 bmidecsr = 0, mask = hwif->channel ? 0x02 : 0x01;
-
- switch (dev->device) {
- case PCI_DEVICE_ID_CMD_648:
- case PCI_DEVICE_ID_CMD_649:
- pci_read_config_byte(dev, BMIDECSR, &bmidecsr);
- return (bmidecsr & mask) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
- default:
- return ATA_CBL_PATA40;
- }
-}
-
-static const struct ide_port_ops cmd64x_port_ops = {
- .set_pio_mode = cmd64x_set_pio_mode,
- .set_dma_mode = cmd64x_set_dma_mode,
- .clear_irq = cmd64x_clear_irq,
- .test_irq = cmd64x_test_irq,
- .cable_detect = cmd64x_cable_detect,
-};
-
-static const struct ide_port_ops cmd648_port_ops = {
- .set_pio_mode = cmd64x_set_pio_mode,
- .set_dma_mode = cmd64x_set_dma_mode,
- .clear_irq = cmd648_clear_irq,
- .test_irq = cmd648_test_irq,
- .cable_detect = cmd64x_cable_detect,
-};
-
-static const struct ide_dma_ops cmd646_rev1_dma_ops = {
- .dma_host_set = ide_dma_host_set,
- .dma_setup = ide_dma_setup,
- .dma_start = ide_dma_start,
- .dma_end = cmd646_1_dma_end,
- .dma_test_irq = ide_dma_test_irq,
- .dma_lost_irq = ide_dma_lost_irq,
- .dma_timer_expiry = ide_dma_sff_timer_expiry,
- .dma_sff_read_status = ide_dma_sff_read_status,
-};
-
-static const struct ide_port_info cmd64x_chipsets[] = {
- { /* 0: CMD643 */
- .name = DRV_NAME,
- .init_chipset = init_chipset_cmd64x,
- .enablebits = {{0x00,0x00,0x00}, {0x51,0x08,0x08}},
- .port_ops = &cmd64x_port_ops,
- .host_flags = IDE_HFLAG_CLEAR_SIMPLEX |
- IDE_HFLAG_ABUSE_PREFETCH |
- IDE_HFLAG_SERIALIZE,
- .pio_mask = ATA_PIO5,
- .mwdma_mask = ATA_MWDMA2,
- .udma_mask = 0x00, /* no udma */
- },
- { /* 1: CMD646 */
- .name = DRV_NAME,
- .init_chipset = init_chipset_cmd64x,
- .enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
- .port_ops = &cmd648_port_ops,
- .host_flags = IDE_HFLAG_ABUSE_PREFETCH |
- IDE_HFLAG_SERIALIZE,
- .pio_mask = ATA_PIO5,
- .mwdma_mask = ATA_MWDMA2,
- .udma_mask = ATA_UDMA2,
- },
- { /* 2: CMD648 */
- .name = DRV_NAME,
- .init_chipset = init_chipset_cmd64x,
- .enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
- .port_ops = &cmd648_port_ops,
- .host_flags = IDE_HFLAG_ABUSE_PREFETCH,
- .pio_mask = ATA_PIO5,
- .mwdma_mask = ATA_MWDMA2,
- .udma_mask = ATA_UDMA4,
- },
- { /* 3: CMD649 */
- .name = DRV_NAME,
- .init_chipset = init_chipset_cmd64x,
- .enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
- .port_ops = &cmd648_port_ops,
- .host_flags = IDE_HFLAG_ABUSE_PREFETCH,
- .pio_mask = ATA_PIO5,
- .mwdma_mask = ATA_MWDMA2,
- .udma_mask = ATA_UDMA5,
- }
-};
-
-static int cmd64x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
- struct ide_port_info d;
- u8 idx = id->driver_data;
-
- d = cmd64x_chipsets[idx];
-
- if (idx == 1) {
- /*
- * UltraDMA only supported on PCI646U and PCI646U2, which
- * correspond to revisions 0x03, 0x05 and 0x07 respectively.
- * Actually, although the CMD tech support people won't
- * tell me the details, the 0x03 revision cannot support
- * UDMA correctly without hardware modifications, and even
- * then it only works with Quantum disks due to some
- * hold time assumptions in the 646U part which are fixed
- * in the 646U2.
- *
- * So we only do UltraDMA on revision 0x05 and 0x07 chipsets.
- */
- if (dev->revision < 5) {
- d.udma_mask = 0x00;
- /*
- * The original PCI0646 didn't have the primary
- * channel enable bit, it appeared starting with
- * PCI0646U (i.e. revision ID 3).
- */
- if (dev->revision < 3) {
- d.enablebits[0].reg = 0;
- d.port_ops = &cmd64x_port_ops;
- if (dev->revision == 1)
- d.dma_ops = &cmd646_rev1_dma_ops;
- }
- }
- }
-
- return ide_pci_init_one(dev, &d, NULL);
-}
-
-static const struct pci_device_id cmd64x_pci_tbl[] = {
- { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_643), 0 },
- { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_646), 1 },
- { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_648), 2 },
- { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_649), 3 },
- { 0, },
-};
-MODULE_DEVICE_TABLE(pci, cmd64x_pci_tbl);
-
-static struct pci_driver cmd64x_pci_driver = {
- .name = "CMD64x_IDE",
- .id_table = cmd64x_pci_tbl,
- .probe = cmd64x_init_one,
- .remove = ide_pci_remove,
- .suspend = ide_pci_suspend,
- .resume = ide_pci_resume,
-};
-
-static int __init cmd64x_ide_init(void)
-{
- return ide_pci_register_driver(&cmd64x_pci_driver);
-}
-
-static void __exit cmd64x_ide_exit(void)
-{
- pci_unregister_driver(&cmd64x_pci_driver);
-}
-
-module_init(cmd64x_ide_init);
-module_exit(cmd64x_ide_exit);
-
-MODULE_AUTHOR("Eddie Dost, David Miller, Andre Hedrick, Bartlomiej Zolnierkiewicz");
-MODULE_DESCRIPTION("PCI driver module for CMD64x IDE");
-MODULE_LICENSE("GPL");
projects / linux-2.6-block.git / blobdiff