+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0
-if ETRAX_ARCH_V10
-
-menu "CRIS v10 options"
-
-# ETRAX 100LX v1 has a MMU "feature" requiring a low mapping
-config CRIS_LOW_MAP
- bool
- depends on ETRAX_ARCH_V10 && ETRAX100LX
- default y
-
-config ETRAX_DRAM_VIRTUAL_BASE
- hex
- depends on ETRAX_ARCH_V10
- default "c0000000" if !ETRAX100LX
- default "60000000" if ETRAX100LX
-
-choice
- prompt "Product LED port"
- depends on ETRAX_ARCH_V10
- default ETRAX_PA_LEDS
-
-config ETRAX_PA_LEDS
- bool "Port-PA-LEDs"
- help
- The ETRAX network driver is responsible for flashing LED's when
- packets arrive and are sent. It uses macros defined in
- <file:arch/cris/include/asm/io.h>, and those macros are defined after
- what YOU choose in this option. The actual bits used are configured
- separately. Select this if the LEDs are on port PA. Some products
- put the leds on PB or a memory-mapped latch (CSP0) instead.
-
-config ETRAX_PB_LEDS
- bool "Port-PB-LEDs"
- help
- The ETRAX network driver is responsible for flashing LED's when
- packets arrive and are sent. It uses macros defined in
- <file:arch/cris/include/asm/io.h>, and those macros are defined after
- what YOU choose in this option. The actual bits used are configured
- separately. Select this if the LEDs are on port PB. Some products
- put the leds on PA or a memory-mapped latch (CSP0) instead.
-
-config ETRAX_CSP0_LEDS
- bool "Port-CSP0-LEDs"
- help
- The ETRAX network driver is responsible for flashing LED's when
- packets arrive and are sent. It uses macros defined in
- <file:arch/cris/include/asm/io.h>, and those macros are defined after
- what YOU choose in this option. The actual bits used are configured
- separately. Select this if the LEDs are on a memory-mapped latch
- using chip select CSP0, this is mapped at 0x90000000.
- Some products put the leds on PA or PB instead.
-
-config ETRAX_NO_LEDS
- bool "None"
- help
- Select this option if you don't have any LED at all.
-
-endchoice
-
-config ETRAX_LED1G
- int "First green LED bit"
- depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS
- default "2"
- help
- Bit to use for the first green LED.
- Most Axis products use bit 2 here.
-
-config ETRAX_LED1R
- int "First red LED bit"
- depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS
- default "3"
- help
- Bit to use for the first red LED.
- Most Axis products use bit 3 here.
- For products with only one controllable LED,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED2G
- int "Second green LED bit"
- depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS
- default "4"
- help
- Bit to use for the second green LED. The "Active" LED.
- Most Axis products use bit 4 here.
- For products with only one controllable LED,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED2R
- int "Second red LED bit"
- depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS
- default "5"
- help
- Bit to use for the second red LED.
- Most Axis products use bit 5 here.
- For products with only one controllable LED,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED3G
- int "Third green LED bit"
- depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS
- default "2"
- help
- Bit to use for the third green LED. The "Drive" LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED3R
- int "Third red LED bit"
- depends on ETRAX_ARCH_V10 && !ETRAX_NO_LEDS
- default "2"
- help
- Bit to use for the third red LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED4R
- int "Fourth red LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the fourth red LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED4G
- int "Fourth green LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the fourth green LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED5R
- int "Fifth red LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the fifth red LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED5G
- int "Fifth green LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the fifth green LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED6R
- int "Sixth red LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the sixth red LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED6G
- int "Sixth green LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the sixth green LED. The "Drive" LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED7R
- int "Seventh red LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the seventh red LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED7G
- int "Seventh green LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the seventh green LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED8Y
- int "Eighth yellow LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the eighth yellow LED. The "Drive" LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED9Y
- int "Ninth yellow LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the ninth yellow LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED10Y
- int "Tenth yellow LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the tenth yellow LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED11Y
- int "Eleventh yellow LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the eleventh yellow LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-config ETRAX_LED12R
- int "Twelfth red LED bit"
- depends on ETRAX_CSP0_LEDS
- default "2"
- help
- Bit to use for the twelfth red LED.
- For products with only one or two controllable LEDs,
- set this to same as CONFIG_ETRAX_LED1G (normally 2).
-
-
-choice
- prompt "Product rescue-port"
- depends on ETRAX_ARCH_V10
- default ETRAX_RESCUE_SER0
-
-config ETRAX_RESCUE_SER0
- bool "Serial-0"
- help
- Select one of the four serial ports as a rescue port. The default
- is port 0.
-
-config ETRAX_RESCUE_SER1
- bool "Serial-1"
- help
- Use serial port 1 as the rescue port.
-
-config ETRAX_RESCUE_SER2
- bool "Serial-2"
- help
- Use serial port 2 as the rescue port.
-
-config ETRAX_RESCUE_SER3
- bool "Serial-3"
- help
- Use serial port 3 as the rescue port.
-
-endchoice
-
-config ETRAX_DEF_R_WAITSTATES
- hex "R_WAITSTATES"
- depends on ETRAX_ARCH_V10
- default "95a6"
- help
- Waitstates for SRAM, Flash and peripherals (not DRAM). 95f8 is a
- good choice for most Axis products...
-
-config ETRAX_DEF_R_BUS_CONFIG
- hex "R_BUS_CONFIG"
- depends on ETRAX_ARCH_V10
- default "104"
- help
- Assorted bits controlling write mode, DMA burst length etc. 104 is
- a good choice for most Axis products...
-
-config ETRAX_SDRAM
- bool "SDRAM support"
- depends on ETRAX_ARCH_V10
- help
- Enable this if you use SDRAM chips and configure
- R_SDRAM_CONFIG and R_SDRAM_TIMING as well.
-
-config ETRAX_DEF_R_DRAM_CONFIG
- hex "R_DRAM_CONFIG"
- depends on ETRAX_ARCH_V10 && !ETRAX_SDRAM
- default "1a200040"
- help
- The R_DRAM_CONFIG register specifies everything on how the DRAM
- chips in the system are connected to the ETRAX CPU. This is
- different depending on the manufacturer, chip type and number of
- chips. So this value often needs to be different for each Axis
- product.
-
-config ETRAX_DEF_R_DRAM_TIMING
- hex "R_DRAM_TIMING"
- depends on ETRAX_ARCH_V10 && !ETRAX_SDRAM
- default "5611"
- help
- Different DRAM chips have different speeds. Current Axis products
- use 50ns DRAM chips which can use the timing: 5611.
-
-config ETRAX_DEF_R_SDRAM_CONFIG
- hex "R_SDRAM_CONFIG"
- depends on ETRAX_ARCH_V10 && ETRAX_SDRAM
- default "d2fa7878"
- help
- The R_SDRAM_CONFIG register specifies everything on how the SDRAM
- chips in the system are connected to the ETRAX CPU. This is
- different depending on the manufacturer, chip type and number of
- chips. So this value often needs to be different for each Axis
- product.
-
-config ETRAX_DEF_R_SDRAM_TIMING
- hex "R_SDRAM_TIMING"
- depends on ETRAX_ARCH_V10 && ETRAX_SDRAM
- default "80004801"
- help
- Different SDRAM chips have different timing.
-
-config ETRAX_DEF_R_PORT_PA_DIR
- hex "R_PORT_PA_DIR"
- depends on ETRAX_ARCH_V10
- default "1c"
- help
- Configures the direction of general port A bits. 1 is out, 0 is in.
- This is often totally different depending on the product used.
- There are some guidelines though - if you know that only LED's are
- connected to port PA, then they are usually connected to bits 2-4
- and you can therefore use 1c. On other boards which don't have the
- LED's at the general ports, these bits are used for all kinds of
- stuff. If you don't know what to use, it is always safe to put all
- as inputs, although floating inputs isn't good.
-
-config ETRAX_DEF_R_PORT_PA_DATA
- hex "R_PORT_PA_DATA"
- depends on ETRAX_ARCH_V10
- default "00"
- help
- Configures the initial data for the general port A bits. Most
- products should use 00 here.
-
-config ETRAX_DEF_R_PORT_PB_CONFIG
- hex "R_PORT_PB_CONFIG"
- depends on ETRAX_ARCH_V10
- default "00"
- help
- Configures the type of the general port B bits. 1 is chip select,
- 0 is port. Most products should use 00 here.
-
-config ETRAX_DEF_R_PORT_PB_DIR
- hex "R_PORT_PB_DIR"
- depends on ETRAX_ARCH_V10
- default "00"
- help
- Configures the direction of general port B bits. 1 is out, 0 is in.
- This is often totally different depending on the product used. Bits
- 0 and 1 on port PB are usually used for I2C communication, but the
- kernel I2C driver sets the appropriate directions itself so you
- don't need to take that into consideration when setting this option.
- If you don't know what to use, it is always safe to put all as
- inputs.
-
-config ETRAX_DEF_R_PORT_PB_DATA
- hex "R_PORT_PB_DATA"
- depends on ETRAX_ARCH_V10
- default "ff"
- help
- Configures the initial data for the general port A bits. Most
- products should use FF here.
-
-config ETRAX_SOFT_SHUTDOWN
- bool "Software Shutdown Support"
- depends on ETRAX_ARCH_V10
- help
- Enable this if ETRAX is used with a power-supply that can be turned
- off and on with PS_ON signal. Gives the possibility to detect
- powerbutton and then do a power off after unmounting disks.
-
-config ETRAX_SHUTDOWN_BIT
- int "Shutdown bit on port CSP0"
- depends on ETRAX_SOFT_SHUTDOWN
- default "12"
- help
- Configure what pin on CSPO-port that is used for controlling power
- supply.
-
-config ETRAX_POWERBUTTON_BIT
- int "Power button bit on port G"
- depends on ETRAX_SOFT_SHUTDOWN
- default "25"
- help
- Configure where power button is connected.
-
-endmenu
-
-endif
projects / linux-2.6-block.git / blobdiff