pinctrl-0 = <&bt_enable_l>, <&wifi_enable_h>;
/*
- * On the module itself this is one of these (depending
- * on the actual card populated):
+ * Depending on the actual card populated GPIO4 D4 and D5
+ * correspond to one of these signals on the module:
+ *
+ * D4:
* - SDIO_RESET_L_WL_REG_ON
* - PDN (power down when low)
+ *
+ * D5:
+ * - BT_I2S_WS_BT_RFDISABLE_L
+ * - No connect
*/
- reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>,
+ <&gpio4 RK_PD5 GPIO_ACTIVE_LOW>;
};
vcc_5v: vcc-5v {
regulator-boot-on;
vin-supply = <&vcc_5v>;
};
+
+ vdd_logic: vdd-logic {
+ compatible = "pwm-regulator";
+ regulator-name = "vdd_logic";
+
+ pwms = <&pwm1 0 1994 0>;
+ pwm-supply = <&vcc33_sys>;
+
+ pwm-dutycycle-range = <0x7b 0>;
+ pwm-dutycycle-unit = <0x94>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <4000>;
+ };
};
&cpu0 {
regulator-max-microvolt = <1250000>;
regulator-ramp-delay = <6001>;
regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <1000000>;
+ regulator-off-in-suspend;
};
};
&uart0 {
status = "okay";
- /* We need to go faster than 24MHz, so adjust clock parents / rates */
- assigned-clocks = <&cru SCLK_UART0>;
- assigned-clock-rates = <48000000>;
-
/* Pins don't include flow control by default; add that in */
pinctrl-names = "default";
pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <
/* Common for sleep and wake, but no owners */
+ &ddr0_retention
+ &ddrio_pwroff
&global_pwroff
>;
pinctrl-1 = <
/* Common for sleep and wake, but no owners */
+ &ddr0_retention
+ &ddrio_pwroff
&global_pwroff
>;
buttons {
pwr_key_l: pwr-key-l {
- rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
emmc {
emmc_reset: emmc-reset {
- rockchip,pins = <2 9 RK_FUNC_GPIO &pcfg_pull_none>;
+ rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
};
/*
* We also have external pulls, so disable the internal ones.
*/
emmc_clk: emmc-clk {
- rockchip,pins = <3 18 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+ rockchip,pins = <3 RK_PC2 2 &pcfg_pull_none_drv_8ma>;
};
emmc_cmd: emmc-cmd {
- rockchip,pins = <3 16 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+ rockchip,pins = <3 RK_PC0 2 &pcfg_pull_none_drv_8ma>;
};
emmc_bus8: emmc-bus8 {
- rockchip,pins = <3 0 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
- <3 1 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
- <3 2 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
- <3 3 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
- <3 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
- <3 5 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
- <3 6 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
- <3 7 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+ rockchip,pins = <3 RK_PA0 2 &pcfg_pull_none_drv_8ma>,
+ <3 RK_PA1 2 &pcfg_pull_none_drv_8ma>,
+ <3 RK_PA2 2 &pcfg_pull_none_drv_8ma>,
+ <3 RK_PA3 2 &pcfg_pull_none_drv_8ma>,
+ <3 RK_PA4 2 &pcfg_pull_none_drv_8ma>,
+ <3 RK_PA5 2 &pcfg_pull_none_drv_8ma>,
+ <3 RK_PA6 2 &pcfg_pull_none_drv_8ma>,
+ <3 RK_PA7 2 &pcfg_pull_none_drv_8ma>;
};
};
pmic {
pmic_int_l: pmic-int-l {
- rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+ rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
reboot {
ap_warm_reset_h: ap-warm-reset-h {
- rockchip,pins = <RK_GPIO0 13 RK_FUNC_GPIO &pcfg_pull_none>;
+ rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
recovery-switch {
rec_mode_l: rec-mode-l {
- rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>;
+ rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
sdio0 {
wifi_enable_h: wifienable-h {
- rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>;
+ rockchip,pins = <4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
};
/* NOTE: mislabelled on schematic; should be bt_enable_h */
bt_enable_l: bt-enable-l {
- rockchip,pins = <4 29 RK_FUNC_GPIO &pcfg_pull_none>;
+ rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
};
/*
* We also have external pulls, so disable the internal ones.
*/
sdio0_bus4: sdio0-bus4 {
- rockchip,pins = <4 20 RK_FUNC_1 &pcfg_pull_none_drv_8ma>,
- <4 21 RK_FUNC_1 &pcfg_pull_none_drv_8ma>,
- <4 22 RK_FUNC_1 &pcfg_pull_none_drv_8ma>,
- <4 23 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ rockchip,pins = <4 RK_PC4 1 &pcfg_pull_none_drv_8ma>,
+ <4 RK_PC5 1 &pcfg_pull_none_drv_8ma>,
+ <4 RK_PC6 1 &pcfg_pull_none_drv_8ma>,
+ <4 RK_PC7 1 &pcfg_pull_none_drv_8ma>;
};
sdio0_cmd: sdio0-cmd {
- rockchip,pins = <4 24 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ rockchip,pins = <4 RK_PD0 1 &pcfg_pull_none_drv_8ma>;
};
sdio0_clk: sdio0-clk {
- rockchip,pins = <4 25 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ rockchip,pins = <4 RK_PD1 1 &pcfg_pull_none_drv_8ma>;
};
};
tpm {
tpm_int_h: tpm-int-h {
- rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_none>;
+ rockchip,pins = <7 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
write-protect {
fw_wp_ap: fw-wp-ap {
- rockchip,pins = <7 6 RK_FUNC_GPIO &pcfg_pull_none>;
+ rockchip,pins = <7 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
};
projects / linux-2.6-block.git / blobdiff