'#', the entire line is discarded as a comment.
So let's look at a really simple job file that defines two processes, each
-randomly reading from a 128MiB file.
+randomly reading from a 128MB file.
; -- start job file --
[global]
Here we have no global section, as we only have one job defined anyway.
We want to use async io here, with a depth of 4 for each file. We also
-increased the buffer size used to 32KiB and define numjobs to 4 to
+increased the buffer size used to 32KB and define numjobs to 4 to
fork 4 identical jobs. The result is 4 processes each randomly writing
-to their own 64MiB file. Instead of using the above job file, you could
+to their own 64MB file. Instead of using the above job file, you could
have given the parameters on the command line. For this case, you would
specify:
$ fio --name=random-writers --ioengine=libaio --iodepth=4 --rw=randwrite --bs=32k --direct=0 --size=64m --numjobs=4
+4.1 Environment variables
+-------------------------
+
fio also supports environment variable expansion in job files. Any
substring of the form "${VARNAME}" as part of an option value (in other
words, on the right of the `='), will be expanded to the value of the
fio ships with a few example job files, you can also look there for
inspiration.
+4.2 Reserved keywords
+---------------------
+
+Additionally, fio has a set of reserved keywords that will be replaced
+internally with the appropriate value. Those keywords are:
+
+$pagesize The architecture page size of the running system
+$mb_memory Megabytes of total memory in the system
+$ncpus Number of online available CPUs
+
+These can be used on the command line or in the job file, and will be
+automatically substituted with the current system values when the job
+is run.
+
5.0 Detailed list of parameters
-------------------------------
a string. The following types are used:
str String. This is a sequence of alpha characters.
-int Integer. A whole number value, can be negative. If prefixed with
- 0x, the integer is assumed to be of base 16 (hexadecimal).
-time Integer with possible time postfix. In seconds unless otherwise
+time Integer with possible time suffix. In seconds unless otherwise
specified, use eg 10m for 10 minutes. Accepts s/m/h for seconds,
minutes, and hours.
-siint SI integer. A whole number value, which may contain a postfix
- describing the base of the number. Accepted postfixes are k/m/g,
- meaning kilo, mega, and giga. So if you want to specify 4096,
- you could either write out '4096' or just give 4k. The postfixes
- signify base 2 values, so 1024 is 1k and 1024k is 1m and so on.
- If the option accepts an upper and lower range, use a colon ':'
- or minus '-' to separate such values. May also include a prefix
- to indicate numbers base. If 0x is used, the number is assumed to
- be hexadecimal. See irange.
+int SI integer. A whole number value, which may contain a suffix
+ describing the base of the number. Accepted suffixes are k/m/g/t/p,
+ meaning kilo, mega, giga, tera, and peta. The suffix is not case
+ sensitive. So if you want to specify 4096, you could either write
+ out '4096' or just give 4k. The suffixes signify base 2 values, so
+ 1024 is 1k and 1024k is 1m and so on. If the option accepts an upper
+ and lower range, use a colon ':' or minus '-' to separate such values.
+ May also include a prefix to indicate numbers base. If 0x is used,
+ the number is assumed to be hexadecimal. See irange.
bool Boolean. Usually parsed as an integer, however only defined for
true and false (1 and 0).
-irange Integer range with postfix. Allows value range to be given, such
+irange Integer range with suffix. Allows value range to be given, such
as 1024-4096. A colon may also be used as the separator, eg
1k:4k. If the option allows two sets of ranges, they can be
specified with a ',' or '/' delimiter: 1k-4k/8k-32k. Also see
- siint.
+ int.
With the above in mind, here follows the complete list of fio job
parameters.
dump this text description when this job is run. It's
not parsed.
-directory=str Prefix filenames with this directory. Used to places files
+directory=str Prefix filenames with this directory. Used to place files
in a different location than "./".
filename=str Fio normally makes up a filename based on the job name,
can specify a number of files by separating the names with a
':' colon. So if you wanted a job to open /dev/sda and /dev/sdb
as the two working files, you would use
- filename=/dev/sda:/dev/sdb. '-' is a reserved name, meaning
- stdin or stdout. Which of the two depends on the read/write
+ filename=/dev/sda:/dev/sdb. If the wanted filename does need to
+ include a colon, then escape that with a '\' character. For
+ instance, if the filename is "/dev/dsk/foo@3,0:c", then you would
+ use filename="/dev/dsk/foo@3,0\:c". '-' is a reserved name,
+ meaning stdin or stdout. Which of the two depends on the read/write
direction set.
opendir=str Tell fio to recursively add any file it can find in this
directory and down the file system tree.
-lockfile=str Fio defaults to not doing any locking files before it does
+lockfile=str Fio defaults to not locking any files before it does
IO to them. If a file or file descriptor is shared, fio
can serialize IO to that file to make the end result
consistent. This is usual for emulating real workloads that
IO's, instead of for every IO. Use rw=randread:8 to specify
that.
+kb_base=int The base unit for a kilobyte. The defacto base is 2^10, 1024.
+ Storage manufacturers like to use 10^3 or 1000 as a base
+ ten unit instead, for obvious reasons. Allow values are
+ 1024 or 1000, with 1024 being the default.
+
randrepeat=bool For random IO workloads, seed the generator in a predictable
way so that results are repeatable across repetitions.
If set, fio will use POSIX_FADV_SEQUENTIAL for sequential
IO and POSIX_FADV_RANDOM for random IO.
-size=siint The total size of file io for this job. Fio will run until
+size=int The total size of file io for this job. Fio will run until
this many bytes has been transferred, unless runtime is
limited by other options (such as 'runtime', for instance).
- Unless specific nr_files and filesize options are given,
+ Unless specific nrfiles and filesize options are given,
fio will divide this size between the available files
specified by the job.
-filesize=siint Individual file sizes. May be a range, in which case fio
+filesize=int Individual file sizes. May be a range, in which case fio
will select sizes for files at random within the given range
and limited to 'size' in total (if that is given). If not
given, each created file is the same size.
fill_device=bool Sets size to something really large and waits for ENOSPC (no
space left on device) as the terminating condition. Only makes
- sense with sequential write.
+ sense with sequential write. For a read workload, the mount
+ point will be filled first then IO started on the result.
-blocksize=siint
-bs=siint The block size used for the io units. Defaults to 4k. Values
- can be given for both read and writes. If a single siint is
- given, it will apply to both. If a second siint is specified
+blocksize=int
+bs=int The block size used for the io units. Defaults to 4k. Values
+ can be given for both read and writes. If a single int is
+ given, it will apply to both. If a second int is specified
after a comma, it will apply to writes only. In other words,
the format is either bs=read_and_write or bs=read,write.
bs=4k,8k will thus use 4k blocks for reads, and 8k blocks
can do so by passing an empty read size - bs=,8k will set
8k for writes and leave the read default value.
+blockalign=int
+ba=int At what boundary to align random IO offsets. Defaults to
+ the same as 'blocksize' the minimum blocksize given.
+ Minimum alignment is typically 512b for using direct IO,
+ though it usually depends on the hardware block size. This
+ option is mutually exclusive with using a random map for
+ files, so it will turn off that option.
+
blocksize_range=irange
bsrange=irange Instead of giving a single block size, specify a range
and fio will mix the issued io block sizes. The issued
always add up to 100, if bssplit is given a range that adds
up to more, it will error out.
+ bssplit also supports giving separate splits to reads and
+ writes. The format is identical to what bs= accepts. You
+ have to separate the read and write parts with a comma. So
+ if you want a workload that has 50% 2k reads and 50% 4k reads,
+ while having 90% 4k writes and 10% 8k writes, you would
+ specify:
+
+ bssplit=2k/50:4k/50,4k/90,8k/10
+
blocksize_unaligned
bs_unaligned If this option is given, any byte size value within bsrange
may be used as a block range. This typically wont work with
buffered=bool If value is true, use buffered io. This is the opposite
of the 'direct' option. Defaults to true.
-offset=siint Start io at the given offset in the file. The data before
+offset=int Start io at the given offset in the file. The data before
the given offset will not be touched. This effectively
caps the file size at real_size - offset.
not sync the file. The exception is the sg io engine, which
synchronizes the disk cache anyway.
+fsyncdata=int Like fsync= but uses fdatasync() to only sync data and not
+ metadata blocks.
+
overwrite=bool If true, writes to a file will always overwrite existing
data. If the file doesn't already exist, it will be
created before the write phase begins. If the file exists
rwmixwrite=int How large a percentage of the mix should be writes. If both
rwmixread and rwmixwrite is given and the values do not add
up to 100%, the latter of the two will be used to override
- the first.
+ the first. This may interfere with a given rate setting,
+ if fio is asked to limit reads or writes to a certain rate.
+ If that is the case, then the distribution may be skewed.
norandommap Normally fio will cover every block of the file when doing
random IO. If this option is given, fio will just get a
defaults to 1 which will make fio wait 'thinktime' usecs
after every block.
-rate=int Cap the bandwidth used by this job to this number of KiB/sec.
+rate=int Cap the bandwidth used by this job. The number is in bytes/sec,
+ the normal suffix rules apply. You can use rate=500k to limit
+ reads and writes to 500k each, or you can specify read and
+ writes separately. Using rate=1m,500k would limit reads to
+ 1MB/sec and writes to 500KB/sec. Capping only reads or
+ writes can be done with rate=,500k or rate=500k,. The former
+ will only limit writes (to 500KB/sec), the latter will only
+ limit reads.
ratemin=int Tell fio to do whatever it can to maintain at least this
bandwidth. Failing to meet this requirement, will cause
- the job to exit.
+ the job to exit. The same format as rate is used for
+ read vs write separation.
rate_iops=int Cap the bandwidth to this number of IOPS. Basically the same
as rate, just specified independently of bandwidth. If the
job is given a block size range instead of a fixed value,
- the smallest block size is used as the metric.
+ the smallest block size is used as the metric. The same format
+ as rate is used for read vs write seperation.
rate_iops_min=int If fio doesn't meet this rate of IO, it will cause
- the job to exit.
+ the job to exit. The same format as rate is used for read vs
+ write seperation.
ratecycle=int Average bandwidth for 'rate' and 'ratemin' over this number
of milliseconds.
that for shmhuge and mmaphuge to work, the system must have
free huge pages allocated. This can normally be checked
and set by reading/writing /proc/sys/vm/nr_hugepages on a
- Linux system. Fio assumes a huge page is 4MiB in size. So
+ Linux system. Fio assumes a huge page is 4MB in size. So
to calculate the number of huge pages you need for a given
job file, add up the io depth of all jobs (normally one unless
iodepth= is used) and multiply by the maximum bs set. Then
location should point there. So if it's mounted in /huge,
you would use mem=mmaphuge:/huge/somefile.
-hugepage-size=siint
+iomem_align=int This indiciates the memory alignment of the IO memory buffers.
+ Note that the given alignment is applied to the first IO unit
+ buffer, if using iodepth the alignment of the following buffers
+ are given by the bs used. In other words, if using a bs that is
+ a multiple of the page sized in the system, all buffers will
+ be aligned to this value. If using a bs that is not page
+ aligned, the alignment of subsequent IO memory buffers is the
+ sum of the iomem_align and bs used.
+
+hugepage-size=int
Defines the size of a huge page. Must at least be equal
- to the system setting, see /proc/meminfo. Defaults to 4MiB.
+ to the system setting, see /proc/meminfo. Defaults to 4MB.
Should probably always be a multiple of megabytes, so using
hugepage-size=Xm is the preferred way to set this to avoid
setting a non-pow-2 bad value.
create_on_open=bool Don't pre-setup the files for IO, just create open()
when it's time to do IO to that file.
+pre_read=bool If this is given, files will be pre-read into memory before
+ starting the given IO operation. This will also clear
+ the 'invalidate' flag, since it is pointless to pre-read
+ and then drop the cache. This will only work for IO engines
+ that are seekable, since they allow you to read the same data
+ multiple times. Thus it will not work on eg network or splice
+ IO.
+
unlink=bool Unlink the job files when done. Not the default, as repeated
runs of that job would then waste time recreating the file
set again and again.
sha256 Use sha256 as the checksum function.
+ sha1 Use optimized sha1 as the checksum function.
+
meta Write extra information about each io
(timestamp, block number etc.). The block
number is verified.
This option can be used for repeated burn-in tests of a
system to make sure that the written data is also
- correctly read back.
+ correctly read back. If the data direction given is
+ a read or random read, fio will assume that it should
+ verify a previously written file. If the data direction
+ includes any form of write, the verify will be of the
+ newly written data.
verifysort=bool If set, fio will sort written verify blocks when it deems
it faster to read them back in a sorted manner. This is
fast IO where the red-black tree sorting CPU time becomes
significant.
-verify_offset=siint Swap the verification header with data somewhere else
+verify_offset=int Swap the verification header with data somewhere else
in the block before writing. Its swapped back before
verifying.
-verify_interval=siint Write the verification header at a finer granularity
+verify_interval=int Write the verification header at a finer granularity
than the blocksize. It will be written for chunks the
size of header_interval. blocksize should divide this
evenly.
before quitting on a block verification failure. If this
option is set, fio will exit the job on the first observed
failure.
+
+verify_async=int Fio will normally verify IO inline from the submitting
+ thread. This option takes an integer describing how many
+ async offload threads to create for IO verification instead,
+ causing fio to offload the duty of verifying IO contents
+ to one or more separate threads. If using this offload
+ option, even sync IO engines can benefit from using an
+ iodepth setting higher than 1, as it allows them to have
+ IO in flight while verifies are running.
+
+verify_async_cpus=str Tell fio to set the given CPU affinity on the
+ async IO verification threads. See cpus_allowed for the
+ format used.
stonewall Wait for preceeding jobs in the job file to exit, before
starting this one. Can be used to insert serialization
given, fio will use pthread_create(3) to create threads
instead.
-zonesize=siint Divide a file into zones of the specified size. See zoneskip.
+zonesize=int Divide a file into zones of the specified size. See zoneskip.
-zoneskip=siint Skip the specified number of bytes when zonesize data has
+zoneskip=int Skip the specified number of bytes when zonesize data has
been read. The two zone options can be used to only do
io on zones of a file.
The actual log names will be foo_clat.log and foo_slat.log.
This helps fio_generate_plot fine the logs automatically.
-lockmem=siint Pin down the specified amount of memory with mlock(2). Can
+lockmem=int Pin down the specified amount of memory with mlock(2). Can
potentially be used instead of removing memory or booting
with less memory to simulate a smaller amount of memory.
percentage of CPU cycles.
cpuchunks=int If the job is a CPU cycle eater, split the load into
- cycles of the given time. In milliseconds.
+ cycles of the given time. In microseconds.
disk_util=bool Generate disk utilization statistics, if the platform
supports it. Defaults to on.
for doing these time calls will be excluded from other
uses. Fio will manually clear it from the CPU mask of other
jobs.
+continue_on_error=bool Normally fio will exit the job on the first observed
+ failure. If this option is set, fio will continue the job when
+ there is a 'non-fatal error' (EIO or EILSEQ) until the runtime
+ is exceeded or the I/O size specified is completed. If this
+ option is used, there are two more stats that are appended,
+ the total error count and the first error. The error field
+ given in the stats is the first error that was hit during the
+ run.
6.0 Interpreting the output
P Thread setup, but not started.
C Thread created.
I Thread initialized, waiting.
+ p Thread running pre-reading file(s).
R Running, doing sequential reads.
r Running, doing random reads.
W Running, doing sequential writes.
M Running, doing mixed sequential reads/writes.
m Running, doing mixed random reads/writes.
F Running, currently waiting for fsync()
-V Running, doing verification of written data.
+ V Running, doing verification of written data.
E Thread exited, not reaped by main thread yet.
_ Thread reaped.
direction, the output looks like:
Client1 (g=0): err= 0:
- write: io= 32MiB, bw= 666KiB/s, runt= 50320msec
+ write: io= 32MB, bw= 666KB/s, runt= 50320msec
slat (msec): min= 0, max= 136, avg= 0.03, stdev= 1.92
clat (msec): min= 0, max= 631, avg=48.50, stdev=86.82
- bw (KiB/s) : min= 0, max= 1196, per=51.00%, avg=664.02, stdev=681.68
+ bw (KB/s) : min= 0, max= 1196, per=51.00%, avg=664.02, stdev=681.68
cpu : usr=1.49%, sys=0.25%, ctx=7969, majf=0, minf=17
IO depths : 1=0.1%, 2=0.3%, 4=0.5%, 8=99.0%, 16=0.0%, 32=0.0%, >32=0.0%
submit : 0=0.0%, 4=100.0%, 8=0.0%, 16=0.0%, 32=0.0%, 64=0.0%, >=64=0.0%
will look like this:
Run status group 0 (all jobs):
- READ: io=64MiB, aggrb=22178, minb=11355, maxb=11814, mint=2840msec, maxt=2955msec
- WRITE: io=64MiB, aggrb=1302, minb=666, maxb=669, mint=50093msec, maxt=50320msec
+ READ: io=64MB, aggrb=22178, minb=11355, maxb=11814, mint=2840msec, maxt=2955msec
+ WRITE: io=64MB, aggrb=1302, minb=666, maxb=669, mint=50093msec, maxt=50320msec
For each data direction, it prints:
jobname, groupid, error
READ status:
- KiB IO, bandwidth (KiB/sec), runtime (msec)
+ KB IO, bandwidth (KB/sec), runtime (msec)
Submission latency: min, max, mean, deviation
Completion latency: min, max, mean, deviation
Bw: min, max, aggregate percentage of total, mean, deviation
WRITE status:
- KiB IO, bandwidth (KiB/sec), runtime (msec)
+ KB IO, bandwidth (KB/sec), runtime (msec)
Submission latency: min, max, mean, deviation
Completion latency: min, max, mean, deviation
Bw: min, max, aggregate percentage of total, mean, deviation