+++ /dev/null
-Decoder firmware API description
-================================
-
-Note: this API is part of the decoder firmware, so it's cx23415 only.
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_PING_FW
-Enum 0/0x00
-Description
- This API call does nothing. It may be used to check if the firmware
- is responding.
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_START_PLAYBACK
-Enum 1/0x01
-Description
- Begin or resume playback.
-Param[0]
- 0 based frame number in GOP to begin playback from.
-Param[1]
- Specifies the number of muted audio frames to play before normal
- audio resumes. (This is not implemented in the firmware, leave at 0)
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_STOP_PLAYBACK
-Enum 2/0x02
-Description
- Ends playback and clears all decoder buffers. If PTS is not zero,
- playback stops at specified PTS.
-Param[0]
- Display 0=last frame, 1=black
- Note: this takes effect immediately, so if you want to wait for a PTS,
- then use '0', otherwise the screen goes to black at once.
- You can call this later (even if there is no playback) with a 1 value
- to set the screen to black.
-Param[1]
- PTS low
-Param[2]
- PTS high
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_PLAYBACK_SPEED
-Enum 3/0x03
-Description
- Playback stream at speed other than normal. There are two modes of
- operation:
- Smooth: host transfers entire stream and firmware drops unused
- frames.
- Coarse: host drops frames based on indexing as required to achieve
- desired speed.
-Param[0]
- Bitmap:
- 0:7 0 normal
- 1 fast only "1.5 times"
- n nX fast, 1/nX slow
- 30 Framedrop:
- '0' during 1.5 times play, every other B frame is dropped
- '1' during 1.5 times play, stream is unchanged (bitrate
- must not exceed 8mbps)
- 31 Speed:
- '0' slow
- '1' fast
- Note: n is limited to 2. Anything higher does not result in
- faster playback. Instead the host should start dropping frames.
-Param[1]
- Direction: 0=forward, 1=reverse
- Note: to make reverse playback work you have to write full GOPs in
- reverse order.
-Param[2]
- Picture mask:
- 1=I frames
- 3=I, P frames
- 7=I, P, B frames
-Param[3]
- B frames per GOP (for reverse play only)
- Note: for reverse playback the Picture Mask should be set to I or I, P.
- Adding B frames to the mask will result in corrupt video. This field
- has to be set to the correct value in order to keep the timing correct.
-Param[4]
- Mute audio: 0=disable, 1=enable
-Param[5]
- Display 0=frame, 1=field
-Param[6]
- Specifies the number of muted audio frames to play before normal audio
- resumes. (Not implemented in the firmware, leave at 0)
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_STEP_VIDEO
-Enum 5/0x05
-Description
- Each call to this API steps the playback to the next unit defined below
- in the current playback direction.
-Param[0]
- 0=frame, 1=top field, 2=bottom field
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_DMA_BLOCK_SIZE
-Enum 8/0x08
-Description
- Set DMA transfer block size. Counterpart to API 0xC9
-Param[0]
- DMA transfer block size in bytes. A different size may be specified
- when issuing the DMA transfer command.
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_GET_XFER_INFO
-Enum 9/0x09
-Description
- This API call may be used to detect an end of stream condition.
-Result[0]
- Stream type
-Result[1]
- Address offset
-Result[2]
- Maximum bytes to transfer
-Result[3]
- Buffer fullness
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_GET_DMA_STATUS
-Enum 10/0x0A
-Description
- Status of the last DMA transfer
-Result[0]
- Bit 1 set means transfer complete
- Bit 2 set means DMA error
- Bit 3 set means linked list error
-Result[1]
- DMA type: 0=MPEG, 1=OSD, 2=YUV
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SCHED_DMA_FROM_HOST
-Enum 11/0x0B
-Description
- Setup DMA from host operation. Counterpart to API 0xCC
-Param[0]
- Memory address of link list
-Param[1]
- Total # of bytes to transfer
-Param[2]
- DMA type (0=MPEG, 1=OSD, 2=YUV)
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_PAUSE_PLAYBACK
-Enum 13/0x0D
-Description
- Freeze playback immediately. In this mode, when internal buffers are
- full, no more data will be accepted and data request IRQs will be
- masked.
-Param[0]
- Display: 0=last frame, 1=black
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_HALT_FW
-Enum 14/0x0E
-Description
- The firmware is halted and no further API calls are serviced until
- the firmware is uploaded again.
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_STANDARD
-Enum 16/0x10
-Description
- Selects display standard
-Param[0]
- 0=NTSC, 1=PAL
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_GET_VERSION
-Enum 17/0x11
-Description
- Returns decoder firmware version information
-Result[0]
- Version bitmask:
- Bits 0:15 build
- Bits 16:23 minor
- Bits 24:31 major
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_STREAM_INPUT
-Enum 20/0x14
-Description
- Select decoder stream input port
-Param[0]
- 0=memory (default), 1=streaming
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_GET_TIMING_INFO
-Enum 21/0x15
-Description
- Returns timing information from start of playback
-Result[0]
- Frame count by decode order
-Result[1]
- Video PTS bits 0:31 by display order
-Result[2]
- Video PTS bit 32 by display order
-Result[3]
- SCR bits 0:31 by display order
-Result[4]
- SCR bit 32 by display order
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_AUDIO_MODE
-Enum 22/0x16
-Description
- Select audio mode
-Param[0]
- Dual mono mode action
- 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
-Param[1]
- Stereo mode action:
- 0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_EVENT_NOTIFICATION
-Enum 23/0x17
-Description
- Setup firmware to notify the host about a particular event.
- Counterpart to API 0xD5
-Param[0]
- Event: 0=Audio mode change between mono, (joint) stereo and dual channel.
- Event: 3=Decoder started
- Event: 4=Unknown: goes off 10-15 times per second while decoding.
- Event: 5=Some sync event: goes off once per frame.
-Param[1]
- Notification 0=disabled, 1=enabled
-Param[2]
- Interrupt bit
-Param[3]
- Mailbox slot, -1 if no mailbox required.
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_DISPLAY_BUFFERS
-Enum 24/0x18
-Description
- Number of display buffers. To decode all frames in reverse playback you
- must use nine buffers.
-Param[0]
- 0=six buffers, 1=nine buffers
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_EXTRACT_VBI
-Enum 25/0x19
-Description
- Extracts VBI data
-Param[0]
- 0=extract from extension & user data, 1=extract from private packets
-Result[0]
- VBI table location
-Result[1]
- VBI table size
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_DECODER_SOURCE
-Enum 26/0x1A
-Description
- Selects decoder source. Ensure that the parameters passed to this
- API match the encoder settings.
-Param[0]
- Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host
-Param[1]
- YUV picture width
-Param[2]
- YUV picture height
-Param[3]
- Bitmap: see Param[0] of API 0xBD
-
--------------------------------------------------------------------------------
-
-Name CX2341X_DEC_SET_PREBUFFERING
-Enum 30/0x1E
-Description
- Decoder prebuffering, when enabled up to 128KB are buffered for
- streams <8mpbs or 640KB for streams >8mbps
-Param[0]
- 0=off, 1=on
projects / linux-2.6-block.git / blobdiff