uart[8250],io,<addr>[,options]
uart[8250],mmio,<addr>[,options]
+ uart[8250],mmio32,<addr>[,options]
+ uart[8250],0x<addr>[,options]
Start an early, polled-mode console on the 8250/16550
UART at the specified I/O port or MMIO address,
- switching to the matching ttyS device later. The
- options are the same as for ttyS, above.
+ switching to the matching ttyS device later.
+ MMIO inter-register address stride is either 8-bit
+ (mmio) or 32-bit (mmio32).
+ If none of [io|mmio|mmio32], <addr> is assumed to be
+ equivalent to 'mmio'. 'options' are specified in the
+ same format described for ttyS above; if unspecified,
+ the h/w is not re-initialized.
+
hvc<n> Use the hypervisor console device <n>. This is for
both Xen and PowerPC hypervisors.
Enable debug messages at boot time. See
Documentation/dynamic-debug-howto.txt for details.
+ eagerfpu= [X86]
+ on enable eager fpu restore
+ off disable eager fpu restore
+ auto selects the default scheme, which automatically
+ enables eagerfpu restore for xsaveopt.
+
early_ioremap_debug [KNL]
Enable debug messages in early_ioremap support. This
is useful for tracking down temporary early mappings
uart[8250],io,<addr>[,options]
uart[8250],mmio,<addr>[,options]
uart[8250],mmio32,<addr>[,options]
+ uart[8250],0x<addr>[,options]
Start an early, polled-mode console on the 8250/16550
UART at the specified I/O port or MMIO address.
MMIO inter-register address stride is either 8-bit
(mmio) or 32-bit (mmio32).
- The options are the same as for ttyS, above.
+ If none of [io|mmio|mmio32], <addr> is assumed to be
+ equivalent to 'mmio'. 'options' are specified in the
+ same format described for "console=ttyS<n>"; if
+ unspecified, the h/w is not initialized.
pl011,<addr>
Start an early, polled-mode console on a pl011 serial
or
memmap=0x10000$0x18690000
+ memmap=nn[KMG]!ss[KMG]
+ [KNL,X86] Mark specific memory as protected.
+ Region of memory to be used, from ss to ss+nn.
+ The memory region may be marked as e820 type 12 (0xc)
+ and is NVDIMM or ADR memory.
+
memory_corruption_check=0/1 [X86]
Some BIOSes seem to corrupt the first 64k of
memory when doing things like suspend/resume.
seconds. Use this parameter to check at some
other rate. 0 disables periodic checking.
- memtest= [KNL,X86] Enable memtest
+ memtest= [KNL,X86,ARM] Enable memtest
Format: <integer>
default : 0 <disable>
Specifies the number of memtest passes to be
noexec32=off: disable non-executable mappings
read implies executable mappings
- nofpu [SH] Disable hardware FPU at boot time.
+ nofpu [MIPS,SH] Disable hardware FPU at boot time.
nofxsr [BUGS=X86-32] Disables x86 floating point extended
register save and restore. The kernel will only save
legacy floating-point registers on task switch.
+ nohugeiomap [KNL,x86] Disable kernel huge I/O mappings.
+
noxsave [BUGS=X86] Disables x86 extended register state save
and restore using xsave. The kernel will fallback to
enabling legacy floating-point and sse state.
parameter, xsave area per process might occupy more
memory on xsaves enabled systems.
- eagerfpu= [X86]
- on enable eager fpu restore
- off disable eager fpu restore
- auto selects the default scheme, which automatically
- enables eagerfpu restore for xsaveopt.
-
nohlt [BUGS=ARM,SH] Tells the kernel that the sleep(SH) or
wfi(ARM) instruction doesn't work correctly and not to
use it. This is also useful when using JTAG debugger.
Set maximum number of finished RCU callbacks to
process in one batch.
+ rcutree.gp_init_delay= [KNL]
+ Set the number of jiffies to delay each step of
+ RCU grace-period initialization. This only has
+ effect when CONFIG_RCU_TORTURE_TEST_SLOW_INIT is
+ set.
+
rcutree.rcu_fanout_leaf= [KNL]
Increase the number of CPUs assigned to each
leaf rcu_node structure. Useful for very large
value is one, and maximum value is HZ.
rcutree.kthread_prio= [KNL,BOOT]
- Set the SCHED_FIFO priority of the RCU
- per-CPU kthreads (rcuc/N). This value is also
- used for the priority of the RCU boost threads
- (rcub/N). Valid values are 1-99 and the default
- is 1 (the least-favored priority).
+ Set the SCHED_FIFO priority of the RCU per-CPU
+ kthreads (rcuc/N). This value is also used for
+ the priority of the RCU boost threads (rcub/N)
+ and for the RCU grace-period kthreads (rcu_bh,
+ rcu_preempt, and rcu_sched). If RCU_BOOST is
+ set, valid values are 1-99 and the default is 1
+ (the least-favored priority). Otherwise, when
+ RCU_BOOST is not set, valid values are 0-99 and
+ the default is zero (non-realtime operation).
rcutree.rcu_nocb_leader_stride= [KNL]
Set the number of NOCB kthread groups, which
improve throughput, but will also increase the
amount of memory reserved for use by the client.
+ suspend.pm_test_delay=
+ [SUSPEND]
+ Sets the number of seconds to remain in a suspend test
+ mode before resuming the system (see
+ /sys/power/pm_test). Only available when CONFIG_PM_DEBUG
+ is set. Default value is 5.
+
swapaccount=[0|1]
[KNL] Enable accounting of swap in memory resource
controller if no parameter or 1 is given or disable
projects / linux-2.6-block.git / blobdiff