docs: admin-guide: add a series of orphaned documents

[linux-2.6-block.git] / Documentation / btmrvl.txt

diff --git a/Documentation/btmrvl.txt b/Documentation/btmrvl.txt
deleted file mode 100644 (file)
index ec57740..0000000
--- a/Documentation/btmrvl.txt
+++ /dev/null
@@ -1,124 +0,0 @@
-=============
-btmrvl driver
-=============
-
-All commands are used via debugfs interface.
-
-Set/get driver configurations
-=============================
-
-Path:  /debug/btmrvl/config/
-
-gpiogap=[n], hscfgcmd
-       These commands are used to configure the host sleep parameters::
-       bit 8:0  -- Gap
-       bit 16:8 -- GPIO
-
-       where GPIO is the pin number of GPIO used to wake up the host.
-       It could be any valid GPIO pin# (e.g. 0-7) or 0xff (SDIO interface
-       wakeup will be used instead).
-
-       where Gap is the gap in milli seconds between wakeup signal and
-       wakeup event, or 0xff for special host sleep setting.
-
-       Usage::
-
-               # Use SDIO interface to wake up the host and set GAP to 0x80:
-               echo 0xff80 > /debug/btmrvl/config/gpiogap
-               echo 1 > /debug/btmrvl/config/hscfgcmd
-
-               # Use GPIO pin #3 to wake up the host and set GAP to 0xff:
-               echo 0x03ff >  /debug/btmrvl/config/gpiogap
-               echo 1 > /debug/btmrvl/config/hscfgcmd
-
-psmode=[n], pscmd
-       These commands are used to enable/disable auto sleep mode
-
-       where the option is::
-
-                       1       -- Enable auto sleep mode
-                       0       -- Disable auto sleep mode
-
-       Usage::
-
-               # Enable auto sleep mode
-               echo 1 > /debug/btmrvl/config/psmode
-               echo 1 > /debug/btmrvl/config/pscmd
-
-               # Disable auto sleep mode
-               echo 0 > /debug/btmrvl/config/psmode
-               echo 1 > /debug/btmrvl/config/pscmd
-
-
-hsmode=[n], hscmd
-       These commands are used to enable host sleep or wake up firmware
-
-       where the option is::
-
-                       1       -- Enable host sleep
-                       0       -- Wake up firmware
-
-       Usage::
-
-               # Enable host sleep
-               echo 1 > /debug/btmrvl/config/hsmode
-               echo 1 > /debug/btmrvl/config/hscmd
-
-               # Wake up firmware
-               echo 0 > /debug/btmrvl/config/hsmode
-               echo 1 > /debug/btmrvl/config/hscmd
-
-
-Get driver status
-=================
-
-Path:  /debug/btmrvl/status/
-
-Usage::
-
-       cat /debug/btmrvl/status/<args>
-
-where the args are:
-
-curpsmode
-       This command displays current auto sleep status.
-
-psstate
-       This command display the power save state.
-
-hsstate
-       This command display the host sleep state.
-
-txdnldrdy
-       This command displays the value of Tx download ready flag.
-
-Issuing a raw hci command
-=========================
-
-Use hcitool to issue raw hci command, refer to hcitool manual
-
-Usage::
-
-       Hcitool cmd <ogf> <ocf> [Parameters]
-
-Interface Control Command::
-
-       hcitool cmd 0x3f 0x5b 0xf5 0x01 0x00    --Enable All interface
-       hcitool cmd 0x3f 0x5b 0xf5 0x01 0x01    --Enable Wlan interface
-       hcitool cmd 0x3f 0x5b 0xf5 0x01 0x02    --Enable BT interface
-       hcitool cmd 0x3f 0x5b 0xf5 0x00 0x00    --Disable All interface
-       hcitool cmd 0x3f 0x5b 0xf5 0x00 0x01    --Disable Wlan interface
-       hcitool cmd 0x3f 0x5b 0xf5 0x00 0x02    --Disable BT interface
-
-SD8688 firmware
-===============
-
-Images:
-
-- /lib/firmware/sd8688_helper.bin
-- /lib/firmware/sd8688.bin
-
-
-The images can be downloaded from:
-
-git.infradead.org/users/dwmw2/linux-firmware.git/libertas/