This mode requires kvm-amd.avic=1.
(Default when IOMMU HW support is present.)
+ amd_pstate= [X86]
+ disable
+ Do not enable amd_pstate as the default
+ scaling driver for the supported processors
+ passive
+ Use amd_pstate with passive mode as a scaling driver.
+ In this mode autonomous selection is disabled.
+ Driver requests a desired performance level and platform
+ tries to match the same performance level if it is
+ satisfied by guaranteed performance level.
+ active
+ Use amd_pstate_epp driver instance as the scaling driver,
+ driver provides a hint to the hardware if software wants
+ to bias toward performance (0x0) or energy efficiency (0xff)
+ to the CPPC firmware. then CPPC power algorithm will
+ calculate the runtime workload and adjust the realtime cores
+ frequency.
+ guided
+ Activate guided autonomous mode. Driver requests minimum and
+ maximum performance level and the platform autonomously
+ selects a performance level in this range and appropriate
+ to the current workload.
+
amijoy.map= [HW,JOY] Amiga joystick support
Map of devices attached to JOY0DAT and JOY1DAT
Format: <a>,<b>
dependencies. This only applies for fw_devlink=on|rpm.
Format: <bool>
+ fw_devlink.sync_state =
+ [KNL] When all devices that could probe have finished
+ probing, this parameter controls what to do with
+ devices that haven't yet received their sync_state()
+ calls.
+ Format: { strict | timeout }
+ strict -- Default. Continue waiting on consumers to
+ probe successfully.
+ timeout -- Give up waiting on consumers and call
+ sync_state() on any devices that haven't yet
+ received their sync_state() calls after
+ deferred_probe_timeout has expired or by
+ late_initcall() if !CONFIG_MODULES.
+
gamecon.map[2|3]=
[HW,JOY] Multisystem joystick and NES/SNES/PSX pad
support via parallel port (up to 5 devices per port)
specified, <module>.async_probe takes precedence for
the specific module.
+ module.enable_dups_trace
+ [KNL] When CONFIG_MODULE_DEBUG_AUTOLOAD_DUPS is set,
+ this means that duplicate request_module() calls will
+ trigger a WARN_ON() instead of a pr_warn(). Note that
+ if MODULE_DEBUG_AUTOLOAD_DUPS_TRACE is set, WARN_ON()s
+ will always be issued and this option does nothing.
module.sig_enforce
[KNL] When CONFIG_MODULE_SIG is set, this means that
modules without (valid) signatures will fail to load.
[KNL] Minimal page reporting order
Format: <integer>
Adjust the minimal page reporting order. The page
- reporting is disabled when it exceeds (MAX_ORDER-1).
+ reporting is disabled when it exceeds MAX_ORDER.
panic= [KNL] Kernel behaviour on panic: delay <timeout>
timeout > 0: seconds before rebooting
later by a loaded module cannot be set this way.
Example: sysctl.vm.swappiness=40
- sysfs.deprecated=0|1 [KNL]
- Enable/disable old style sysfs layout for old udev
- on older distributions. When this option is enabled
- very new udev will not work anymore. When this option
- is disabled (or CONFIG_SYSFS_DEPRECATED not compiled)
- in older udev will not work anymore.
- Default depends on CONFIG_SYSFS_DEPRECATED_V2 set in
- the kernel configuration.
-
sysrq_always_enabled
[KNL]
Ignore sysrq setting - this boot parameter will
xmon commands.
off xmon is disabled.
- amd_pstate= [X86]
- disable
- Do not enable amd_pstate as the default
- scaling driver for the supported processors
- passive
- Use amd_pstate as a scaling driver, driver requests a
- desired performance on this abstract scale and the power
- management firmware translates the requests into actual
- hardware states (core frequency, data fabric and memory
- clocks etc.)
- active
- Use amd_pstate_epp driver instance as the scaling driver,
- driver provides a hint to the hardware if software wants
- to bias toward performance (0x0) or energy efficiency (0xff)
- to the CPPC firmware. then CPPC power algorithm will
- calculate the runtime workload and adjust the realtime cores
- frequency.