1 // SPDX-License-Identifier: GPL-2.0-only
3 * wm8960.c -- WM8960 ALSA SoC Audio driver
5 * Copyright 2007-11 Wolfson Microelectronics, plc
7 * Author: Liam Girdwood
10 #include <linux/module.h>
11 #include <linux/moduleparam.h>
12 #include <linux/init.h>
13 #include <linux/delay.h>
15 #include <linux/clk.h>
16 #include <linux/i2c.h>
17 #include <linux/slab.h>
18 #include <sound/core.h>
19 #include <sound/pcm.h>
20 #include <sound/pcm_params.h>
21 #include <sound/soc.h>
22 #include <sound/initval.h>
23 #include <sound/tlv.h>
24 #include <sound/wm8960.h>
29 #define WM8960_VMID_MASK 0x180
30 #define WM8960_VREF 0x40
33 #define WM8960_PWR2_LOUT1 0x40
34 #define WM8960_PWR2_ROUT1 0x20
35 #define WM8960_PWR2_OUT3 0x02
37 /* R28 - Anti-pop 1 */
38 #define WM8960_POBCTRL 0x80
39 #define WM8960_BUFDCOPEN 0x10
40 #define WM8960_BUFIOEN 0x08
41 #define WM8960_SOFT_ST 0x04
42 #define WM8960_HPSTBY 0x01
44 /* R29 - Anti-pop 2 */
45 #define WM8960_DISOP 0x40
46 #define WM8960_DRES_MASK 0x30
48 static bool is_pll_freq_available(unsigned int source, unsigned int target);
49 static int wm8960_set_pll(struct snd_soc_component *component,
50 unsigned int freq_in, unsigned int freq_out);
52 * wm8960 register cache
53 * We can't read the WM8960 register space when we are
54 * using 2 wire for device control, so we cache them instead.
56 static const struct reg_default wm8960_reg_defaults[] = {
110 static bool wm8960_volatile(struct device *dev, unsigned int reg)
122 struct regmap *regmap;
123 int (*set_bias_level)(struct snd_soc_component *,
124 enum snd_soc_bias_level level);
125 struct snd_soc_dapm_widget *lout1;
126 struct snd_soc_dapm_widget *rout1;
127 struct snd_soc_dapm_widget *out3;
134 bool is_stream_in_use[2];
135 struct wm8960_data pdata;
138 #define wm8960_reset(c) regmap_write(c, WM8960_RESET, 0)
140 /* enumerated controls */
141 static const char *wm8960_polarity[] = {"No Inversion", "Left Inverted",
142 "Right Inverted", "Stereo Inversion"};
143 static const char *wm8960_3d_upper_cutoff[] = {"High", "Low"};
144 static const char *wm8960_3d_lower_cutoff[] = {"Low", "High"};
145 static const char *wm8960_alcfunc[] = {"Off", "Right", "Left", "Stereo"};
146 static const char *wm8960_alcmode[] = {"ALC", "Limiter"};
147 static const char *wm8960_adc_data_output_sel[] = {
148 "Left Data = Left ADC; Right Data = Right ADC",
149 "Left Data = Left ADC; Right Data = Left ADC",
150 "Left Data = Right ADC; Right Data = Right ADC",
151 "Left Data = Right ADC; Right Data = Left ADC",
153 static const char *wm8960_dmonomix[] = {"Stereo", "Mono"};
155 static const struct soc_enum wm8960_enum[] = {
156 SOC_ENUM_SINGLE(WM8960_DACCTL1, 5, 4, wm8960_polarity),
157 SOC_ENUM_SINGLE(WM8960_DACCTL2, 5, 4, wm8960_polarity),
158 SOC_ENUM_SINGLE(WM8960_3D, 6, 2, wm8960_3d_upper_cutoff),
159 SOC_ENUM_SINGLE(WM8960_3D, 5, 2, wm8960_3d_lower_cutoff),
160 SOC_ENUM_SINGLE(WM8960_ALC1, 7, 4, wm8960_alcfunc),
161 SOC_ENUM_SINGLE(WM8960_ALC3, 8, 2, wm8960_alcmode),
162 SOC_ENUM_SINGLE(WM8960_ADDCTL1, 2, 4, wm8960_adc_data_output_sel),
163 SOC_ENUM_SINGLE(WM8960_ADDCTL1, 4, 2, wm8960_dmonomix),
166 static const int deemph_settings[] = { 0, 32000, 44100, 48000 };
168 static int wm8960_set_deemph(struct snd_soc_component *component)
170 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
173 /* If we're using deemphasis select the nearest available sample
176 if (wm8960->deemph) {
178 for (i = 2; i < ARRAY_SIZE(deemph_settings); i++) {
179 if (abs(deemph_settings[i] - wm8960->lrclk) <
180 abs(deemph_settings[best] - wm8960->lrclk))
189 dev_dbg(component->dev, "Set deemphasis %d\n", val);
191 return snd_soc_component_update_bits(component, WM8960_DACCTL1,
195 static int wm8960_get_deemph(struct snd_kcontrol *kcontrol,
196 struct snd_ctl_elem_value *ucontrol)
198 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
199 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
201 ucontrol->value.integer.value[0] = wm8960->deemph;
205 static int wm8960_put_deemph(struct snd_kcontrol *kcontrol,
206 struct snd_ctl_elem_value *ucontrol)
208 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
209 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
210 unsigned int deemph = ucontrol->value.integer.value[0];
215 wm8960->deemph = deemph;
217 return wm8960_set_deemph(component);
220 static const DECLARE_TLV_DB_SCALE(adc_tlv, -9750, 50, 1);
221 static const DECLARE_TLV_DB_SCALE(inpga_tlv, -1725, 75, 0);
222 static const DECLARE_TLV_DB_SCALE(dac_tlv, -12750, 50, 1);
223 static const DECLARE_TLV_DB_SCALE(bypass_tlv, -2100, 300, 0);
224 static const DECLARE_TLV_DB_SCALE(out_tlv, -12100, 100, 1);
225 static const DECLARE_TLV_DB_SCALE(lineinboost_tlv, -1500, 300, 1);
226 static const SNDRV_CTL_TLVD_DECLARE_DB_RANGE(micboost_tlv,
227 0, 1, TLV_DB_SCALE_ITEM(0, 1300, 0),
228 2, 3, TLV_DB_SCALE_ITEM(2000, 900, 0),
231 static const struct snd_kcontrol_new wm8960_snd_controls[] = {
232 SOC_DOUBLE_R_TLV("Capture Volume", WM8960_LINVOL, WM8960_RINVOL,
233 0, 63, 0, inpga_tlv),
234 SOC_DOUBLE_R("Capture Volume ZC Switch", WM8960_LINVOL, WM8960_RINVOL,
236 SOC_DOUBLE_R("Capture Switch", WM8960_LINVOL, WM8960_RINVOL,
239 SOC_SINGLE_TLV("Left Input Boost Mixer LINPUT3 Volume",
240 WM8960_INBMIX1, 4, 7, 0, lineinboost_tlv),
241 SOC_SINGLE_TLV("Left Input Boost Mixer LINPUT2 Volume",
242 WM8960_INBMIX1, 1, 7, 0, lineinboost_tlv),
243 SOC_SINGLE_TLV("Right Input Boost Mixer RINPUT3 Volume",
244 WM8960_INBMIX2, 4, 7, 0, lineinboost_tlv),
245 SOC_SINGLE_TLV("Right Input Boost Mixer RINPUT2 Volume",
246 WM8960_INBMIX2, 1, 7, 0, lineinboost_tlv),
247 SOC_SINGLE_TLV("Right Input Boost Mixer RINPUT1 Volume",
248 WM8960_RINPATH, 4, 3, 0, micboost_tlv),
249 SOC_SINGLE_TLV("Left Input Boost Mixer LINPUT1 Volume",
250 WM8960_LINPATH, 4, 3, 0, micboost_tlv),
252 SOC_DOUBLE_R_TLV("Playback Volume", WM8960_LDAC, WM8960_RDAC,
255 SOC_DOUBLE_R_TLV("Headphone Playback Volume", WM8960_LOUT1, WM8960_ROUT1,
257 SOC_DOUBLE_R("Headphone Playback ZC Switch", WM8960_LOUT1, WM8960_ROUT1,
260 SOC_DOUBLE_R_TLV("Speaker Playback Volume", WM8960_LOUT2, WM8960_ROUT2,
262 SOC_DOUBLE_R("Speaker Playback ZC Switch", WM8960_LOUT2, WM8960_ROUT2,
264 SOC_SINGLE("Speaker DC Volume", WM8960_CLASSD3, 3, 5, 0),
265 SOC_SINGLE("Speaker AC Volume", WM8960_CLASSD3, 0, 5, 0),
267 SOC_SINGLE("PCM Playback -6dB Switch", WM8960_DACCTL1, 7, 1, 0),
268 SOC_ENUM("ADC Polarity", wm8960_enum[0]),
269 SOC_SINGLE("ADC High Pass Filter Switch", WM8960_DACCTL1, 0, 1, 0),
271 SOC_ENUM("DAC Polarity", wm8960_enum[1]),
272 SOC_SINGLE_BOOL_EXT("DAC Deemphasis Switch", 0,
273 wm8960_get_deemph, wm8960_put_deemph),
275 SOC_ENUM("3D Filter Upper Cut-Off", wm8960_enum[2]),
276 SOC_ENUM("3D Filter Lower Cut-Off", wm8960_enum[3]),
277 SOC_SINGLE("3D Volume", WM8960_3D, 1, 15, 0),
278 SOC_SINGLE("3D Switch", WM8960_3D, 0, 1, 0),
280 SOC_ENUM("ALC Function", wm8960_enum[4]),
281 SOC_SINGLE("ALC Max Gain", WM8960_ALC1, 4, 7, 0),
282 SOC_SINGLE("ALC Target", WM8960_ALC1, 0, 15, 1),
283 SOC_SINGLE("ALC Min Gain", WM8960_ALC2, 4, 7, 0),
284 SOC_SINGLE("ALC Hold Time", WM8960_ALC2, 0, 15, 0),
285 SOC_ENUM("ALC Mode", wm8960_enum[5]),
286 SOC_SINGLE("ALC Decay", WM8960_ALC3, 4, 15, 0),
287 SOC_SINGLE("ALC Attack", WM8960_ALC3, 0, 15, 0),
289 SOC_SINGLE("Noise Gate Threshold", WM8960_NOISEG, 3, 31, 0),
290 SOC_SINGLE("Noise Gate Switch", WM8960_NOISEG, 0, 1, 0),
292 SOC_DOUBLE_R_TLV("ADC PCM Capture Volume", WM8960_LADC, WM8960_RADC,
295 SOC_SINGLE_TLV("Left Output Mixer Boost Bypass Volume",
296 WM8960_BYPASS1, 4, 7, 1, bypass_tlv),
297 SOC_SINGLE_TLV("Left Output Mixer LINPUT3 Volume",
298 WM8960_LOUTMIX, 4, 7, 1, bypass_tlv),
299 SOC_SINGLE_TLV("Right Output Mixer Boost Bypass Volume",
300 WM8960_BYPASS2, 4, 7, 1, bypass_tlv),
301 SOC_SINGLE_TLV("Right Output Mixer RINPUT3 Volume",
302 WM8960_ROUTMIX, 4, 7, 1, bypass_tlv),
304 SOC_ENUM("ADC Data Output Select", wm8960_enum[6]),
305 SOC_ENUM("DAC Mono Mix", wm8960_enum[7]),
308 static const struct snd_kcontrol_new wm8960_lin_boost[] = {
309 SOC_DAPM_SINGLE("LINPUT2 Switch", WM8960_LINPATH, 6, 1, 0),
310 SOC_DAPM_SINGLE("LINPUT3 Switch", WM8960_LINPATH, 7, 1, 0),
311 SOC_DAPM_SINGLE("LINPUT1 Switch", WM8960_LINPATH, 8, 1, 0),
314 static const struct snd_kcontrol_new wm8960_lin[] = {
315 SOC_DAPM_SINGLE("Boost Switch", WM8960_LINPATH, 3, 1, 0),
318 static const struct snd_kcontrol_new wm8960_rin_boost[] = {
319 SOC_DAPM_SINGLE("RINPUT2 Switch", WM8960_RINPATH, 6, 1, 0),
320 SOC_DAPM_SINGLE("RINPUT3 Switch", WM8960_RINPATH, 7, 1, 0),
321 SOC_DAPM_SINGLE("RINPUT1 Switch", WM8960_RINPATH, 8, 1, 0),
324 static const struct snd_kcontrol_new wm8960_rin[] = {
325 SOC_DAPM_SINGLE("Boost Switch", WM8960_RINPATH, 3, 1, 0),
328 static const struct snd_kcontrol_new wm8960_loutput_mixer[] = {
329 SOC_DAPM_SINGLE("PCM Playback Switch", WM8960_LOUTMIX, 8, 1, 0),
330 SOC_DAPM_SINGLE("LINPUT3 Switch", WM8960_LOUTMIX, 7, 1, 0),
331 SOC_DAPM_SINGLE("Boost Bypass Switch", WM8960_BYPASS1, 7, 1, 0),
334 static const struct snd_kcontrol_new wm8960_routput_mixer[] = {
335 SOC_DAPM_SINGLE("PCM Playback Switch", WM8960_ROUTMIX, 8, 1, 0),
336 SOC_DAPM_SINGLE("RINPUT3 Switch", WM8960_ROUTMIX, 7, 1, 0),
337 SOC_DAPM_SINGLE("Boost Bypass Switch", WM8960_BYPASS2, 7, 1, 0),
340 static const struct snd_kcontrol_new wm8960_mono_out[] = {
341 SOC_DAPM_SINGLE("Left Switch", WM8960_MONOMIX1, 7, 1, 0),
342 SOC_DAPM_SINGLE("Right Switch", WM8960_MONOMIX2, 7, 1, 0),
345 static const struct snd_soc_dapm_widget wm8960_dapm_widgets[] = {
346 SND_SOC_DAPM_INPUT("LINPUT1"),
347 SND_SOC_DAPM_INPUT("RINPUT1"),
348 SND_SOC_DAPM_INPUT("LINPUT2"),
349 SND_SOC_DAPM_INPUT("RINPUT2"),
350 SND_SOC_DAPM_INPUT("LINPUT3"),
351 SND_SOC_DAPM_INPUT("RINPUT3"),
353 SND_SOC_DAPM_SUPPLY("MICB", WM8960_POWER1, 1, 0, NULL, 0),
355 SND_SOC_DAPM_MIXER("Left Boost Mixer", WM8960_POWER1, 5, 0,
356 wm8960_lin_boost, ARRAY_SIZE(wm8960_lin_boost)),
357 SND_SOC_DAPM_MIXER("Right Boost Mixer", WM8960_POWER1, 4, 0,
358 wm8960_rin_boost, ARRAY_SIZE(wm8960_rin_boost)),
360 SND_SOC_DAPM_MIXER("Left Input Mixer", WM8960_POWER3, 5, 0,
361 wm8960_lin, ARRAY_SIZE(wm8960_lin)),
362 SND_SOC_DAPM_MIXER("Right Input Mixer", WM8960_POWER3, 4, 0,
363 wm8960_rin, ARRAY_SIZE(wm8960_rin)),
365 SND_SOC_DAPM_ADC("Left ADC", "Capture", WM8960_POWER1, 3, 0),
366 SND_SOC_DAPM_ADC("Right ADC", "Capture", WM8960_POWER1, 2, 0),
368 SND_SOC_DAPM_DAC("Left DAC", "Playback", WM8960_POWER2, 8, 0),
369 SND_SOC_DAPM_DAC("Right DAC", "Playback", WM8960_POWER2, 7, 0),
371 SND_SOC_DAPM_MIXER("Left Output Mixer", WM8960_POWER3, 3, 0,
372 &wm8960_loutput_mixer[0],
373 ARRAY_SIZE(wm8960_loutput_mixer)),
374 SND_SOC_DAPM_MIXER("Right Output Mixer", WM8960_POWER3, 2, 0,
375 &wm8960_routput_mixer[0],
376 ARRAY_SIZE(wm8960_routput_mixer)),
378 SND_SOC_DAPM_PGA("LOUT1 PGA", WM8960_POWER2, 6, 0, NULL, 0),
379 SND_SOC_DAPM_PGA("ROUT1 PGA", WM8960_POWER2, 5, 0, NULL, 0),
381 SND_SOC_DAPM_PGA("Left Speaker PGA", WM8960_POWER2, 4, 0, NULL, 0),
382 SND_SOC_DAPM_PGA("Right Speaker PGA", WM8960_POWER2, 3, 0, NULL, 0),
384 SND_SOC_DAPM_PGA("Right Speaker Output", WM8960_CLASSD1, 7, 0, NULL, 0),
385 SND_SOC_DAPM_PGA("Left Speaker Output", WM8960_CLASSD1, 6, 0, NULL, 0),
387 SND_SOC_DAPM_OUTPUT("SPK_LP"),
388 SND_SOC_DAPM_OUTPUT("SPK_LN"),
389 SND_SOC_DAPM_OUTPUT("HP_L"),
390 SND_SOC_DAPM_OUTPUT("HP_R"),
391 SND_SOC_DAPM_OUTPUT("SPK_RP"),
392 SND_SOC_DAPM_OUTPUT("SPK_RN"),
393 SND_SOC_DAPM_OUTPUT("OUT3"),
396 static const struct snd_soc_dapm_widget wm8960_dapm_widgets_out3[] = {
397 SND_SOC_DAPM_MIXER("Mono Output Mixer", WM8960_POWER2, 1, 0,
399 ARRAY_SIZE(wm8960_mono_out)),
402 /* Represent OUT3 as a PGA so that it gets turned on with LOUT1/ROUT1 */
403 static const struct snd_soc_dapm_widget wm8960_dapm_widgets_capless[] = {
404 SND_SOC_DAPM_PGA("OUT3 VMID", WM8960_POWER2, 1, 0, NULL, 0),
407 static const struct snd_soc_dapm_route audio_paths[] = {
408 { "Left Boost Mixer", "LINPUT1 Switch", "LINPUT1" },
409 { "Left Boost Mixer", "LINPUT2 Switch", "LINPUT2" },
410 { "Left Boost Mixer", "LINPUT3 Switch", "LINPUT3" },
412 { "Left Input Mixer", "Boost Switch", "Left Boost Mixer" },
413 { "Left Input Mixer", "Boost Switch", "LINPUT1" }, /* Really Boost Switch */
414 { "Left Input Mixer", NULL, "LINPUT2" },
415 { "Left Input Mixer", NULL, "LINPUT3" },
417 { "Right Boost Mixer", "RINPUT1 Switch", "RINPUT1" },
418 { "Right Boost Mixer", "RINPUT2 Switch", "RINPUT2" },
419 { "Right Boost Mixer", "RINPUT3 Switch", "RINPUT3" },
421 { "Right Input Mixer", "Boost Switch", "Right Boost Mixer" },
422 { "Right Input Mixer", "Boost Switch", "RINPUT1" }, /* Really Boost Switch */
423 { "Right Input Mixer", NULL, "RINPUT2" },
424 { "Right Input Mixer", NULL, "RINPUT3" },
426 { "Left ADC", NULL, "Left Input Mixer" },
427 { "Right ADC", NULL, "Right Input Mixer" },
429 { "Left Output Mixer", "LINPUT3 Switch", "LINPUT3" },
430 { "Left Output Mixer", "Boost Bypass Switch", "Left Boost Mixer" },
431 { "Left Output Mixer", "PCM Playback Switch", "Left DAC" },
433 { "Right Output Mixer", "RINPUT3 Switch", "RINPUT3" },
434 { "Right Output Mixer", "Boost Bypass Switch", "Right Boost Mixer" },
435 { "Right Output Mixer", "PCM Playback Switch", "Right DAC" },
437 { "LOUT1 PGA", NULL, "Left Output Mixer" },
438 { "ROUT1 PGA", NULL, "Right Output Mixer" },
440 { "HP_L", NULL, "LOUT1 PGA" },
441 { "HP_R", NULL, "ROUT1 PGA" },
443 { "Left Speaker PGA", NULL, "Left Output Mixer" },
444 { "Right Speaker PGA", NULL, "Right Output Mixer" },
446 { "Left Speaker Output", NULL, "Left Speaker PGA" },
447 { "Right Speaker Output", NULL, "Right Speaker PGA" },
449 { "SPK_LN", NULL, "Left Speaker Output" },
450 { "SPK_LP", NULL, "Left Speaker Output" },
451 { "SPK_RN", NULL, "Right Speaker Output" },
452 { "SPK_RP", NULL, "Right Speaker Output" },
455 static const struct snd_soc_dapm_route audio_paths_out3[] = {
456 { "Mono Output Mixer", "Left Switch", "Left Output Mixer" },
457 { "Mono Output Mixer", "Right Switch", "Right Output Mixer" },
459 { "OUT3", NULL, "Mono Output Mixer", }
462 static const struct snd_soc_dapm_route audio_paths_capless[] = {
463 { "HP_L", NULL, "OUT3 VMID" },
464 { "HP_R", NULL, "OUT3 VMID" },
466 { "OUT3 VMID", NULL, "Left Output Mixer" },
467 { "OUT3 VMID", NULL, "Right Output Mixer" },
470 static int wm8960_add_widgets(struct snd_soc_component *component)
472 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
473 struct wm8960_data *pdata = &wm8960->pdata;
474 struct snd_soc_dapm_context *dapm = snd_soc_component_get_dapm(component);
475 struct snd_soc_dapm_widget *w;
477 snd_soc_dapm_new_controls(dapm, wm8960_dapm_widgets,
478 ARRAY_SIZE(wm8960_dapm_widgets));
480 snd_soc_dapm_add_routes(dapm, audio_paths, ARRAY_SIZE(audio_paths));
482 /* In capless mode OUT3 is used to provide VMID for the
483 * headphone outputs, otherwise it is used as a mono mixer.
485 if (pdata && pdata->capless) {
486 snd_soc_dapm_new_controls(dapm, wm8960_dapm_widgets_capless,
487 ARRAY_SIZE(wm8960_dapm_widgets_capless));
489 snd_soc_dapm_add_routes(dapm, audio_paths_capless,
490 ARRAY_SIZE(audio_paths_capless));
492 snd_soc_dapm_new_controls(dapm, wm8960_dapm_widgets_out3,
493 ARRAY_SIZE(wm8960_dapm_widgets_out3));
495 snd_soc_dapm_add_routes(dapm, audio_paths_out3,
496 ARRAY_SIZE(audio_paths_out3));
499 /* We need to power up the headphone output stage out of
500 * sequence for capless mode. To save scanning the widget
501 * list each time to find the desired power state do so now
502 * and save the result.
504 list_for_each_entry(w, &component->card->widgets, list) {
507 if (strcmp(w->name, "LOUT1 PGA") == 0)
509 if (strcmp(w->name, "ROUT1 PGA") == 0)
511 if (strcmp(w->name, "OUT3 VMID") == 0)
518 static int wm8960_set_dai_fmt(struct snd_soc_dai *codec_dai,
521 struct snd_soc_component *component = codec_dai->component;
524 /* set master/slave audio interface */
525 switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
526 case SND_SOC_DAIFMT_CBM_CFM:
529 case SND_SOC_DAIFMT_CBS_CFS:
535 /* interface format */
536 switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
537 case SND_SOC_DAIFMT_I2S:
540 case SND_SOC_DAIFMT_RIGHT_J:
542 case SND_SOC_DAIFMT_LEFT_J:
545 case SND_SOC_DAIFMT_DSP_A:
548 case SND_SOC_DAIFMT_DSP_B:
555 /* clock inversion */
556 switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
557 case SND_SOC_DAIFMT_NB_NF:
559 case SND_SOC_DAIFMT_IB_IF:
562 case SND_SOC_DAIFMT_IB_NF:
565 case SND_SOC_DAIFMT_NB_IF:
573 snd_soc_component_write(component, WM8960_IFACE1, iface);
592 /* -1 for reserved value */
593 static const int sysclk_divs[] = { 1, -1, 2, -1 };
595 /* Multiply 256 for internal 256 div */
596 static const int dac_divs[] = { 256, 384, 512, 768, 1024, 1408, 1536 };
598 /* Multiply 10 to eliminate decimials */
599 static const int bclk_divs[] = {
600 10, 15, 20, 30, 40, 55, 60, 80, 110,
601 120, 160, 220, 240, 320, 320, 320
605 * wm8960_configure_sysclk - checks if there is a sysclk frequency available
606 * The sysclk must be chosen such that:
607 * - sysclk = MCLK / sysclk_divs
608 * - lrclk = sysclk / dac_divs
609 * - 10 * bclk = sysclk / bclk_divs
611 * @wm8960: codec private data
612 * @mclk: MCLK used to derive sysclk
613 * @sysclk_idx: sysclk_divs index for found sysclk
614 * @dac_idx: dac_divs index for found lrclk
615 * @bclk_idx: bclk_divs index for found bclk
618 * -1, in case no sysclk frequency available found
619 * >=0, in case we could derive bclk and lrclk from sysclk using
620 * (@sysclk_idx, @dac_idx, @bclk_idx) dividers
623 int wm8960_configure_sysclk(struct wm8960_priv *wm8960, int mclk,
624 int *sysclk_idx, int *dac_idx, int *bclk_idx)
626 int sysclk, bclk, lrclk;
630 /* marker for no match */
634 lrclk = wm8960->lrclk;
636 /* check if the sysclk frequency is available. */
637 for (i = 0; i < ARRAY_SIZE(sysclk_divs); ++i) {
638 if (sysclk_divs[i] == -1)
640 sysclk = mclk / sysclk_divs[i];
641 for (j = 0; j < ARRAY_SIZE(dac_divs); ++j) {
642 if (sysclk != dac_divs[j] * lrclk)
644 for (k = 0; k < ARRAY_SIZE(bclk_divs); ++k) {
645 diff = sysclk - bclk * bclk_divs[k] / 10;
653 if (k != ARRAY_SIZE(bclk_divs))
656 if (j != ARRAY_SIZE(dac_divs))
663 * wm8960_configure_pll - checks if there is a PLL out frequency available
664 * The PLL out frequency must be chosen such that:
665 * - sysclk = lrclk * dac_divs
666 * - freq_out = sysclk * sysclk_divs
667 * - 10 * sysclk = bclk * bclk_divs
669 * If we cannot find an exact match for (sysclk, lrclk, bclk)
670 * triplet, we relax the bclk such that bclk is chosen as the
671 * closest available frequency greater than expected bclk.
673 * @component: component structure
674 * @freq_in: input frequency used to derive freq out via PLL
675 * @sysclk_idx: sysclk_divs index for found sysclk
676 * @dac_idx: dac_divs index for found lrclk
677 * @bclk_idx: bclk_divs index for found bclk
680 * < 0, in case no PLL frequency out available was found
681 * >=0, in case we could derive bclk, lrclk, sysclk from PLL out using
682 * (@sysclk_idx, @dac_idx, @bclk_idx) dividers
685 int wm8960_configure_pll(struct snd_soc_component *component, int freq_in,
686 int *sysclk_idx, int *dac_idx, int *bclk_idx)
688 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
689 int sysclk, bclk, lrclk, freq_out;
690 int diff, closest, best_freq_out;
694 lrclk = wm8960->lrclk;
697 best_freq_out = -EINVAL;
698 *sysclk_idx = *dac_idx = *bclk_idx = -1;
701 * From Datasheet, the PLL performs best when f2 is between
702 * 90MHz and 100MHz, the desired sysclk output is 11.2896MHz
703 * or 12.288MHz, then sysclkdiv = 2 is the best choice.
704 * So search sysclk_divs from 2 to 1 other than from 1 to 2.
706 for (i = ARRAY_SIZE(sysclk_divs) - 1; i >= 0; --i) {
707 if (sysclk_divs[i] == -1)
709 for (j = 0; j < ARRAY_SIZE(dac_divs); ++j) {
710 sysclk = lrclk * dac_divs[j];
711 freq_out = sysclk * sysclk_divs[i];
713 for (k = 0; k < ARRAY_SIZE(bclk_divs); ++k) {
714 if (!is_pll_freq_available(freq_in, freq_out))
717 diff = sysclk - bclk * bclk_divs[k] / 10;
724 if (diff > 0 && closest > diff) {
729 best_freq_out = freq_out;
735 return best_freq_out;
737 static int wm8960_configure_clocking(struct snd_soc_component *component)
739 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
740 int freq_out, freq_in;
741 u16 iface1 = snd_soc_component_read(component, WM8960_IFACE1);
746 * For Slave mode clocking should still be configured,
747 * so this if statement should be removed, but some platform
748 * may not work if the sysclk is not configured, to avoid such
749 * compatible issue, just add '!wm8960->sysclk' condition in
752 if (!(iface1 & (1 << 6)) && !wm8960->sysclk) {
753 dev_warn(component->dev,
754 "slave mode, but proceeding with no clock configuration\n");
758 if (wm8960->clk_id != WM8960_SYSCLK_MCLK && !wm8960->freq_in) {
759 dev_err(component->dev, "No MCLK configured\n");
763 freq_in = wm8960->freq_in;
765 * If it's sysclk auto mode, check if the MCLK can provide sysclk or
766 * not. If MCLK can provide sysclk, using MCLK to provide sysclk
767 * directly. Otherwise, auto select a available pll out frequency
770 if (wm8960->clk_id == WM8960_SYSCLK_AUTO) {
771 /* disable the PLL and using MCLK to provide sysclk */
772 wm8960_set_pll(component, 0, 0);
774 } else if (wm8960->sysclk) {
775 freq_out = wm8960->sysclk;
777 dev_err(component->dev, "No SYSCLK configured\n");
781 if (wm8960->clk_id != WM8960_SYSCLK_PLL) {
782 ret = wm8960_configure_sysclk(wm8960, freq_out, &i, &j, &k);
784 goto configure_clock;
785 } else if (wm8960->clk_id != WM8960_SYSCLK_AUTO) {
786 dev_err(component->dev, "failed to configure clock\n");
791 freq_out = wm8960_configure_pll(component, freq_in, &i, &j, &k);
793 dev_err(component->dev, "failed to configure clock via PLL\n");
796 wm8960_set_pll(component, freq_in, freq_out);
799 /* configure sysclk clock */
800 snd_soc_component_update_bits(component, WM8960_CLOCK1, 3 << 1, i << 1);
802 /* configure frame clock */
803 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x7 << 3, j << 3);
804 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x7 << 6, j << 6);
806 /* configure bit clock */
807 snd_soc_component_update_bits(component, WM8960_CLOCK2, 0xf, k);
812 static int wm8960_hw_params(struct snd_pcm_substream *substream,
813 struct snd_pcm_hw_params *params,
814 struct snd_soc_dai *dai)
816 struct snd_soc_component *component = dai->component;
817 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
818 u16 iface = snd_soc_component_read(component, WM8960_IFACE1) & 0xfff3;
819 bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK;
822 wm8960->bclk = snd_soc_params_to_bclk(params);
823 if (params_channels(params) == 1)
827 switch (params_width(params)) {
837 /* right justify mode does not support 32 word length */
838 if ((iface & 0x3) != 0) {
844 dev_err(component->dev, "unsupported width %d\n",
845 params_width(params));
849 wm8960->lrclk = params_rate(params);
850 /* Update filters for the new rate */
852 wm8960_set_deemph(component);
854 for (i = 0; i < ARRAY_SIZE(alc_rates); i++)
855 if (alc_rates[i].rate == params_rate(params))
856 snd_soc_component_update_bits(component,
862 snd_soc_component_write(component, WM8960_IFACE1, iface);
864 wm8960->is_stream_in_use[tx] = true;
866 if (!wm8960->is_stream_in_use[!tx])
867 return wm8960_configure_clocking(component);
872 static int wm8960_hw_free(struct snd_pcm_substream *substream,
873 struct snd_soc_dai *dai)
875 struct snd_soc_component *component = dai->component;
876 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
877 bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK;
879 wm8960->is_stream_in_use[tx] = false;
884 static int wm8960_mute(struct snd_soc_dai *dai, int mute, int direction)
886 struct snd_soc_component *component = dai->component;
889 snd_soc_component_update_bits(component, WM8960_DACCTL1, 0x8, 0x8);
891 snd_soc_component_update_bits(component, WM8960_DACCTL1, 0x8, 0);
895 static int wm8960_set_bias_level_out3(struct snd_soc_component *component,
896 enum snd_soc_bias_level level)
898 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
899 u16 pm2 = snd_soc_component_read(component, WM8960_POWER2);
903 case SND_SOC_BIAS_ON:
906 case SND_SOC_BIAS_PREPARE:
907 switch (snd_soc_component_get_bias_level(component)) {
908 case SND_SOC_BIAS_STANDBY:
909 if (!IS_ERR(wm8960->mclk)) {
910 ret = clk_prepare_enable(wm8960->mclk);
912 dev_err(component->dev,
913 "Failed to enable MCLK: %d\n",
919 ret = wm8960_configure_clocking(component);
923 /* Set VMID to 2x50k */
924 snd_soc_component_update_bits(component, WM8960_POWER1, 0x180, 0x80);
927 case SND_SOC_BIAS_ON:
929 * If it's sysclk auto mode, and the pll is enabled,
932 if (wm8960->clk_id == WM8960_SYSCLK_AUTO && (pm2 & 0x1))
933 wm8960_set_pll(component, 0, 0);
935 if (!IS_ERR(wm8960->mclk))
936 clk_disable_unprepare(wm8960->mclk);
945 case SND_SOC_BIAS_STANDBY:
946 if (snd_soc_component_get_bias_level(component) == SND_SOC_BIAS_OFF) {
947 regcache_sync(wm8960->regmap);
949 /* Enable anti-pop features */
950 snd_soc_component_write(component, WM8960_APOP1,
951 WM8960_POBCTRL | WM8960_SOFT_ST |
952 WM8960_BUFDCOPEN | WM8960_BUFIOEN);
954 /* Enable & ramp VMID at 2x50k */
955 snd_soc_component_update_bits(component, WM8960_POWER1, 0x80, 0x80);
959 snd_soc_component_update_bits(component, WM8960_POWER1, WM8960_VREF,
962 /* Disable anti-pop features */
963 snd_soc_component_write(component, WM8960_APOP1, WM8960_BUFIOEN);
966 /* Set VMID to 2x250k */
967 snd_soc_component_update_bits(component, WM8960_POWER1, 0x180, 0x100);
970 case SND_SOC_BIAS_OFF:
971 /* Enable anti-pop features */
972 snd_soc_component_write(component, WM8960_APOP1,
973 WM8960_POBCTRL | WM8960_SOFT_ST |
974 WM8960_BUFDCOPEN | WM8960_BUFIOEN);
976 /* Disable VMID and VREF, let them discharge */
977 snd_soc_component_write(component, WM8960_POWER1, 0);
985 static int wm8960_set_bias_level_capless(struct snd_soc_component *component,
986 enum snd_soc_bias_level level)
988 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
989 u16 pm2 = snd_soc_component_read(component, WM8960_POWER2);
993 case SND_SOC_BIAS_ON:
996 case SND_SOC_BIAS_PREPARE:
997 switch (snd_soc_component_get_bias_level(component)) {
998 case SND_SOC_BIAS_STANDBY:
999 /* Enable anti pop mode */
1000 snd_soc_component_update_bits(component, WM8960_APOP1,
1001 WM8960_POBCTRL | WM8960_SOFT_ST |
1003 WM8960_POBCTRL | WM8960_SOFT_ST |
1006 /* Enable LOUT1, ROUT1 and OUT3 if they're enabled */
1008 if (wm8960->lout1 && wm8960->lout1->power)
1009 reg |= WM8960_PWR2_LOUT1;
1010 if (wm8960->rout1 && wm8960->rout1->power)
1011 reg |= WM8960_PWR2_ROUT1;
1012 if (wm8960->out3 && wm8960->out3->power)
1013 reg |= WM8960_PWR2_OUT3;
1014 snd_soc_component_update_bits(component, WM8960_POWER2,
1017 WM8960_PWR2_OUT3, reg);
1019 /* Enable VMID at 2*50k */
1020 snd_soc_component_update_bits(component, WM8960_POWER1,
1021 WM8960_VMID_MASK, 0x80);
1027 snd_soc_component_update_bits(component, WM8960_POWER1,
1028 WM8960_VREF, WM8960_VREF);
1032 if (!IS_ERR(wm8960->mclk)) {
1033 ret = clk_prepare_enable(wm8960->mclk);
1035 dev_err(component->dev,
1036 "Failed to enable MCLK: %d\n",
1042 ret = wm8960_configure_clocking(component);
1048 case SND_SOC_BIAS_ON:
1050 * If it's sysclk auto mode, and the pll is enabled,
1053 if (wm8960->clk_id == WM8960_SYSCLK_AUTO && (pm2 & 0x1))
1054 wm8960_set_pll(component, 0, 0);
1056 if (!IS_ERR(wm8960->mclk))
1057 clk_disable_unprepare(wm8960->mclk);
1059 /* Enable anti-pop mode */
1060 snd_soc_component_update_bits(component, WM8960_APOP1,
1061 WM8960_POBCTRL | WM8960_SOFT_ST |
1063 WM8960_POBCTRL | WM8960_SOFT_ST |
1066 /* Disable VMID and VREF */
1067 snd_soc_component_update_bits(component, WM8960_POWER1,
1068 WM8960_VREF | WM8960_VMID_MASK, 0);
1071 case SND_SOC_BIAS_OFF:
1072 regcache_sync(wm8960->regmap);
1079 case SND_SOC_BIAS_STANDBY:
1080 switch (snd_soc_component_get_bias_level(component)) {
1081 case SND_SOC_BIAS_PREPARE:
1082 /* Disable HP discharge */
1083 snd_soc_component_update_bits(component, WM8960_APOP2,
1084 WM8960_DISOP | WM8960_DRES_MASK,
1087 /* Disable anti-pop features */
1088 snd_soc_component_update_bits(component, WM8960_APOP1,
1089 WM8960_POBCTRL | WM8960_SOFT_ST |
1091 WM8960_POBCTRL | WM8960_SOFT_ST |
1100 case SND_SOC_BIAS_OFF:
1114 static bool is_pll_freq_available(unsigned int source, unsigned int target)
1118 if (source == 0 || target == 0)
1121 /* Scale up target to PLL operating frequency */
1123 Ndiv = target / source;
1127 Ndiv = target / source;
1130 if ((Ndiv < 6) || (Ndiv > 12))
1136 /* The size in bits of the pll divide multiplied by 10
1137 * to allow rounding later */
1138 #define FIXED_PLL_SIZE ((1 << 24) * 10)
1140 static int pll_factors(unsigned int source, unsigned int target,
1141 struct _pll_div *pll_div)
1143 unsigned long long Kpart;
1144 unsigned int K, Ndiv, Nmod;
1146 pr_debug("WM8960 PLL: setting %dHz->%dHz\n", source, target);
1148 /* Scale up target to PLL operating frequency */
1151 Ndiv = target / source;
1154 pll_div->pre_div = 1;
1155 Ndiv = target / source;
1157 pll_div->pre_div = 0;
1159 if ((Ndiv < 6) || (Ndiv > 12)) {
1160 pr_err("WM8960 PLL: Unsupported N=%d\n", Ndiv);
1165 Nmod = target % source;
1166 Kpart = FIXED_PLL_SIZE * (long long)Nmod;
1168 do_div(Kpart, source);
1170 K = Kpart & 0xFFFFFFFF;
1172 /* Check if we need to round */
1176 /* Move down to proper range now rounding is done */
1181 pr_debug("WM8960 PLL: N=%x K=%x pre_div=%d\n",
1182 pll_div->n, pll_div->k, pll_div->pre_div);
1187 static int wm8960_set_pll(struct snd_soc_component *component,
1188 unsigned int freq_in, unsigned int freq_out)
1191 static struct _pll_div pll_div;
1194 if (freq_in && freq_out) {
1195 ret = pll_factors(freq_in, freq_out, &pll_div);
1200 /* Disable the PLL: even if we are changing the frequency the
1201 * PLL needs to be disabled while we do so. */
1202 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x1, 0);
1203 snd_soc_component_update_bits(component, WM8960_POWER2, 0x1, 0);
1205 if (!freq_in || !freq_out)
1208 reg = snd_soc_component_read(component, WM8960_PLL1) & ~0x3f;
1209 reg |= pll_div.pre_div << 4;
1215 snd_soc_component_write(component, WM8960_PLL2, (pll_div.k >> 16) & 0xff);
1216 snd_soc_component_write(component, WM8960_PLL3, (pll_div.k >> 8) & 0xff);
1217 snd_soc_component_write(component, WM8960_PLL4, pll_div.k & 0xff);
1219 snd_soc_component_write(component, WM8960_PLL1, reg);
1222 snd_soc_component_update_bits(component, WM8960_POWER2, 0x1, 0x1);
1224 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x1, 0x1);
1229 static int wm8960_set_dai_pll(struct snd_soc_dai *codec_dai, int pll_id,
1230 int source, unsigned int freq_in, unsigned int freq_out)
1232 struct snd_soc_component *component = codec_dai->component;
1233 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
1235 wm8960->freq_in = freq_in;
1237 if (pll_id == WM8960_SYSCLK_AUTO)
1240 return wm8960_set_pll(component, freq_in, freq_out);
1243 static int wm8960_set_dai_clkdiv(struct snd_soc_dai *codec_dai,
1244 int div_id, int div)
1246 struct snd_soc_component *component = codec_dai->component;
1250 case WM8960_SYSCLKDIV:
1251 reg = snd_soc_component_read(component, WM8960_CLOCK1) & 0x1f9;
1252 snd_soc_component_write(component, WM8960_CLOCK1, reg | div);
1255 reg = snd_soc_component_read(component, WM8960_CLOCK1) & 0x1c7;
1256 snd_soc_component_write(component, WM8960_CLOCK1, reg | div);
1258 case WM8960_OPCLKDIV:
1259 reg = snd_soc_component_read(component, WM8960_PLL1) & 0x03f;
1260 snd_soc_component_write(component, WM8960_PLL1, reg | div);
1262 case WM8960_DCLKDIV:
1263 reg = snd_soc_component_read(component, WM8960_CLOCK2) & 0x03f;
1264 snd_soc_component_write(component, WM8960_CLOCK2, reg | div);
1266 case WM8960_TOCLKSEL:
1267 reg = snd_soc_component_read(component, WM8960_ADDCTL1) & 0x1fd;
1268 snd_soc_component_write(component, WM8960_ADDCTL1, reg | div);
1277 static int wm8960_set_bias_level(struct snd_soc_component *component,
1278 enum snd_soc_bias_level level)
1280 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
1282 return wm8960->set_bias_level(component, level);
1285 static int wm8960_set_dai_sysclk(struct snd_soc_dai *dai, int clk_id,
1286 unsigned int freq, int dir)
1288 struct snd_soc_component *component = dai->component;
1289 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
1292 case WM8960_SYSCLK_MCLK:
1293 snd_soc_component_update_bits(component, WM8960_CLOCK1,
1294 0x1, WM8960_SYSCLK_MCLK);
1296 case WM8960_SYSCLK_PLL:
1297 snd_soc_component_update_bits(component, WM8960_CLOCK1,
1298 0x1, WM8960_SYSCLK_PLL);
1300 case WM8960_SYSCLK_AUTO:
1306 wm8960->sysclk = freq;
1307 wm8960->clk_id = clk_id;
1312 #define WM8960_RATES SNDRV_PCM_RATE_8000_48000
1314 #define WM8960_FORMATS \
1315 (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \
1316 SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE)
1318 static const struct snd_soc_dai_ops wm8960_dai_ops = {
1319 .hw_params = wm8960_hw_params,
1320 .hw_free = wm8960_hw_free,
1321 .mute_stream = wm8960_mute,
1322 .set_fmt = wm8960_set_dai_fmt,
1323 .set_clkdiv = wm8960_set_dai_clkdiv,
1324 .set_pll = wm8960_set_dai_pll,
1325 .set_sysclk = wm8960_set_dai_sysclk,
1326 .no_capture_mute = 1,
1329 static struct snd_soc_dai_driver wm8960_dai = {
1330 .name = "wm8960-hifi",
1332 .stream_name = "Playback",
1335 .rates = WM8960_RATES,
1336 .formats = WM8960_FORMATS,},
1338 .stream_name = "Capture",
1341 .rates = WM8960_RATES,
1342 .formats = WM8960_FORMATS,},
1343 .ops = &wm8960_dai_ops,
1344 .symmetric_rate = 1,
1347 static int wm8960_probe(struct snd_soc_component *component)
1349 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
1350 struct wm8960_data *pdata = &wm8960->pdata;
1353 wm8960->set_bias_level = wm8960_set_bias_level_capless;
1355 wm8960->set_bias_level = wm8960_set_bias_level_out3;
1357 snd_soc_add_component_controls(component, wm8960_snd_controls,
1358 ARRAY_SIZE(wm8960_snd_controls));
1359 wm8960_add_widgets(component);
1364 static const struct snd_soc_component_driver soc_component_dev_wm8960 = {
1365 .probe = wm8960_probe,
1366 .set_bias_level = wm8960_set_bias_level,
1367 .suspend_bias_off = 1,
1369 .use_pmdown_time = 1,
1371 .non_legacy_dai_naming = 1,
1374 static const struct regmap_config wm8960_regmap = {
1377 .max_register = WM8960_PLL4,
1379 .reg_defaults = wm8960_reg_defaults,
1380 .num_reg_defaults = ARRAY_SIZE(wm8960_reg_defaults),
1381 .cache_type = REGCACHE_RBTREE,
1383 .volatile_reg = wm8960_volatile,
1386 static void wm8960_set_pdata_from_of(struct i2c_client *i2c,
1387 struct wm8960_data *pdata)
1389 const struct device_node *np = i2c->dev.of_node;
1391 if (of_property_read_bool(np, "wlf,capless"))
1392 pdata->capless = true;
1394 if (of_property_read_bool(np, "wlf,shared-lrclk"))
1395 pdata->shared_lrclk = true;
1397 of_property_read_u32_array(np, "wlf,gpio-cfg", pdata->gpio_cfg,
1398 ARRAY_SIZE(pdata->gpio_cfg));
1400 of_property_read_u32_array(np, "wlf,hp-cfg", pdata->hp_cfg,
1401 ARRAY_SIZE(pdata->hp_cfg));
1404 static int wm8960_i2c_probe(struct i2c_client *i2c,
1405 const struct i2c_device_id *id)
1407 struct wm8960_data *pdata = dev_get_platdata(&i2c->dev);
1408 struct wm8960_priv *wm8960;
1411 wm8960 = devm_kzalloc(&i2c->dev, sizeof(struct wm8960_priv),
1416 wm8960->mclk = devm_clk_get(&i2c->dev, "mclk");
1417 if (IS_ERR(wm8960->mclk)) {
1418 if (PTR_ERR(wm8960->mclk) == -EPROBE_DEFER)
1419 return -EPROBE_DEFER;
1422 wm8960->regmap = devm_regmap_init_i2c(i2c, &wm8960_regmap);
1423 if (IS_ERR(wm8960->regmap))
1424 return PTR_ERR(wm8960->regmap);
1427 memcpy(&wm8960->pdata, pdata, sizeof(struct wm8960_data));
1428 else if (i2c->dev.of_node)
1429 wm8960_set_pdata_from_of(i2c, &wm8960->pdata);
1431 ret = wm8960_reset(wm8960->regmap);
1433 dev_err(&i2c->dev, "Failed to issue reset\n");
1437 if (wm8960->pdata.shared_lrclk) {
1438 ret = regmap_update_bits(wm8960->regmap, WM8960_ADDCTL2,
1441 dev_err(&i2c->dev, "Failed to enable LRCM: %d\n",
1447 /* Latch the update bits */
1448 regmap_update_bits(wm8960->regmap, WM8960_LINVOL, 0x100, 0x100);
1449 regmap_update_bits(wm8960->regmap, WM8960_RINVOL, 0x100, 0x100);
1450 regmap_update_bits(wm8960->regmap, WM8960_LADC, 0x100, 0x100);
1451 regmap_update_bits(wm8960->regmap, WM8960_RADC, 0x100, 0x100);
1452 regmap_update_bits(wm8960->regmap, WM8960_LDAC, 0x100, 0x100);
1453 regmap_update_bits(wm8960->regmap, WM8960_RDAC, 0x100, 0x100);
1454 regmap_update_bits(wm8960->regmap, WM8960_LOUT1, 0x100, 0x100);
1455 regmap_update_bits(wm8960->regmap, WM8960_ROUT1, 0x100, 0x100);
1456 regmap_update_bits(wm8960->regmap, WM8960_LOUT2, 0x100, 0x100);
1457 regmap_update_bits(wm8960->regmap, WM8960_ROUT2, 0x100, 0x100);
1459 /* ADCLRC pin configured as GPIO. */
1460 regmap_update_bits(wm8960->regmap, WM8960_IFACE2, 1 << 6,
1461 wm8960->pdata.gpio_cfg[0] << 6);
1462 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL4, 0xF << 4,
1463 wm8960->pdata.gpio_cfg[1] << 4);
1465 /* Enable headphone jack detect */
1466 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL4, 3 << 2,
1467 wm8960->pdata.hp_cfg[0] << 2);
1468 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL2, 3 << 5,
1469 wm8960->pdata.hp_cfg[1] << 5);
1470 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL1, 3,
1471 wm8960->pdata.hp_cfg[2]);
1473 i2c_set_clientdata(i2c, wm8960);
1475 ret = devm_snd_soc_register_component(&i2c->dev,
1476 &soc_component_dev_wm8960, &wm8960_dai, 1);
1481 static int wm8960_i2c_remove(struct i2c_client *client)
1486 static const struct i2c_device_id wm8960_i2c_id[] = {
1490 MODULE_DEVICE_TABLE(i2c, wm8960_i2c_id);
1492 static const struct of_device_id wm8960_of_match[] = {
1493 { .compatible = "wlf,wm8960", },
1496 MODULE_DEVICE_TABLE(of, wm8960_of_match);
1498 static struct i2c_driver wm8960_i2c_driver = {
1501 .of_match_table = wm8960_of_match,
1503 .probe = wm8960_i2c_probe,
1504 .remove = wm8960_i2c_remove,
1505 .id_table = wm8960_i2c_id,
1508 module_i2c_driver(wm8960_i2c_driver);
1510 MODULE_DESCRIPTION("ASoC WM8960 driver");
1511 MODULE_AUTHOR("Liam Girdwood");
1512 MODULE_LICENSE("GPL");