Merge branch 'powerpc-next' of master.kernel.org:/pub/scm/linux/kernel/git/galak...
[linux-2.6-block.git] / drivers / scsi / sd.c
1 /*
2  *      sd.c Copyright (C) 1992 Drew Eckhardt
3  *           Copyright (C) 1993, 1994, 1995, 1999 Eric Youngdale
4  *
5  *      Linux scsi disk driver
6  *              Initial versions: Drew Eckhardt
7  *              Subsequent revisions: Eric Youngdale
8  *      Modification history:
9  *       - Drew Eckhardt <drew@colorado.edu> original
10  *       - Eric Youngdale <eric@andante.org> add scatter-gather, multiple 
11  *         outstanding request, and other enhancements.
12  *         Support loadable low-level scsi drivers.
13  *       - Jirka Hanika <geo@ff.cuni.cz> support more scsi disks using 
14  *         eight major numbers.
15  *       - Richard Gooch <rgooch@atnf.csiro.au> support devfs.
16  *       - Torben Mathiasen <tmm@image.dk> Resource allocation fixes in 
17  *         sd_init and cleanups.
18  *       - Alex Davis <letmein@erols.com> Fix problem where partition info
19  *         not being read in sd_open. Fix problem where removable media 
20  *         could be ejected after sd_open.
21  *       - Douglas Gilbert <dgilbert@interlog.com> cleanup for lk 2.5.x
22  *       - Badari Pulavarty <pbadari@us.ibm.com>, Matthew Wilcox 
23  *         <willy@debian.org>, Kurt Garloff <garloff@suse.de>: 
24  *         Support 32k/1M disks.
25  *
26  *      Logging policy (needs CONFIG_SCSI_LOGGING defined):
27  *       - setting up transfer: SCSI_LOG_HLQUEUE levels 1 and 2
28  *       - end of transfer (bh + scsi_lib): SCSI_LOG_HLCOMPLETE level 1
29  *       - entering sd_ioctl: SCSI_LOG_IOCTL level 1
30  *       - entering other commands: SCSI_LOG_HLQUEUE level 3
31  *      Note: when the logging level is set by the user, it must be greater
32  *      than the level indicated above to trigger output.       
33  */
34
35 #include <linux/module.h>
36 #include <linux/fs.h>
37 #include <linux/kernel.h>
38 #include <linux/mm.h>
39 #include <linux/bio.h>
40 #include <linux/genhd.h>
41 #include <linux/hdreg.h>
42 #include <linux/errno.h>
43 #include <linux/idr.h>
44 #include <linux/interrupt.h>
45 #include <linux/init.h>
46 #include <linux/blkdev.h>
47 #include <linux/blkpg.h>
48 #include <linux/delay.h>
49 #include <linux/mutex.h>
50 #include <asm/uaccess.h>
51
52 #include <scsi/scsi.h>
53 #include <scsi/scsi_cmnd.h>
54 #include <scsi/scsi_dbg.h>
55 #include <scsi/scsi_device.h>
56 #include <scsi/scsi_driver.h>
57 #include <scsi/scsi_eh.h>
58 #include <scsi/scsi_host.h>
59 #include <scsi/scsi_ioctl.h>
60 #include <scsi/scsicam.h>
61 #include <scsi/sd.h>
62
63 #include "scsi_logging.h"
64
65 MODULE_AUTHOR("Eric Youngdale");
66 MODULE_DESCRIPTION("SCSI disk (sd) driver");
67 MODULE_LICENSE("GPL");
68
69 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK0_MAJOR);
70 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK1_MAJOR);
71 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK2_MAJOR);
72 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK3_MAJOR);
73 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK4_MAJOR);
74 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK5_MAJOR);
75 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK6_MAJOR);
76 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK7_MAJOR);
77 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK8_MAJOR);
78 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK9_MAJOR);
79 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK10_MAJOR);
80 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK11_MAJOR);
81 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK12_MAJOR);
82 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK13_MAJOR);
83 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK14_MAJOR);
84 MODULE_ALIAS_BLOCKDEV_MAJOR(SCSI_DISK15_MAJOR);
85 MODULE_ALIAS_SCSI_DEVICE(TYPE_DISK);
86 MODULE_ALIAS_SCSI_DEVICE(TYPE_MOD);
87 MODULE_ALIAS_SCSI_DEVICE(TYPE_RBC);
88
89 static int  sd_revalidate_disk(struct gendisk *);
90 static int  sd_probe(struct device *);
91 static int  sd_remove(struct device *);
92 static void sd_shutdown(struct device *);
93 static int sd_suspend(struct device *, pm_message_t state);
94 static int sd_resume(struct device *);
95 static void sd_rescan(struct device *);
96 static int sd_done(struct scsi_cmnd *);
97 static void sd_read_capacity(struct scsi_disk *sdkp, unsigned char *buffer);
98 static void scsi_disk_release(struct device *cdev);
99 static void sd_print_sense_hdr(struct scsi_disk *, struct scsi_sense_hdr *);
100 static void sd_print_result(struct scsi_disk *, int);
101
102 static DEFINE_IDR(sd_index_idr);
103 static DEFINE_SPINLOCK(sd_index_lock);
104
105 /* This semaphore is used to mediate the 0->1 reference get in the
106  * face of object destruction (i.e. we can't allow a get on an
107  * object after last put) */
108 static DEFINE_MUTEX(sd_ref_mutex);
109
110 static const char *sd_cache_types[] = {
111         "write through", "none", "write back",
112         "write back, no read (daft)"
113 };
114
115 static ssize_t
116 sd_store_cache_type(struct device *dev, struct device_attribute *attr,
117                     const char *buf, size_t count)
118 {
119         int i, ct = -1, rcd, wce, sp;
120         struct scsi_disk *sdkp = to_scsi_disk(dev);
121         struct scsi_device *sdp = sdkp->device;
122         char buffer[64];
123         char *buffer_data;
124         struct scsi_mode_data data;
125         struct scsi_sense_hdr sshdr;
126         int len;
127
128         if (sdp->type != TYPE_DISK)
129                 /* no cache control on RBC devices; theoretically they
130                  * can do it, but there's probably so many exceptions
131                  * it's not worth the risk */
132                 return -EINVAL;
133
134         for (i = 0; i < ARRAY_SIZE(sd_cache_types); i++) {
135                 const int len = strlen(sd_cache_types[i]);
136                 if (strncmp(sd_cache_types[i], buf, len) == 0 &&
137                     buf[len] == '\n') {
138                         ct = i;
139                         break;
140                 }
141         }
142         if (ct < 0)
143                 return -EINVAL;
144         rcd = ct & 0x01 ? 1 : 0;
145         wce = ct & 0x02 ? 1 : 0;
146         if (scsi_mode_sense(sdp, 0x08, 8, buffer, sizeof(buffer), SD_TIMEOUT,
147                             SD_MAX_RETRIES, &data, NULL))
148                 return -EINVAL;
149         len = min_t(size_t, sizeof(buffer), data.length - data.header_length -
150                   data.block_descriptor_length);
151         buffer_data = buffer + data.header_length +
152                 data.block_descriptor_length;
153         buffer_data[2] &= ~0x05;
154         buffer_data[2] |= wce << 2 | rcd;
155         sp = buffer_data[0] & 0x80 ? 1 : 0;
156
157         if (scsi_mode_select(sdp, 1, sp, 8, buffer_data, len, SD_TIMEOUT,
158                              SD_MAX_RETRIES, &data, &sshdr)) {
159                 if (scsi_sense_valid(&sshdr))
160                         sd_print_sense_hdr(sdkp, &sshdr);
161                 return -EINVAL;
162         }
163         sd_revalidate_disk(sdkp->disk);
164         return count;
165 }
166
167 static ssize_t
168 sd_store_manage_start_stop(struct device *dev, struct device_attribute *attr,
169                            const char *buf, size_t count)
170 {
171         struct scsi_disk *sdkp = to_scsi_disk(dev);
172         struct scsi_device *sdp = sdkp->device;
173
174         if (!capable(CAP_SYS_ADMIN))
175                 return -EACCES;
176
177         sdp->manage_start_stop = simple_strtoul(buf, NULL, 10);
178
179         return count;
180 }
181
182 static ssize_t
183 sd_store_allow_restart(struct device *dev, struct device_attribute *attr,
184                        const char *buf, size_t count)
185 {
186         struct scsi_disk *sdkp = to_scsi_disk(dev);
187         struct scsi_device *sdp = sdkp->device;
188
189         if (!capable(CAP_SYS_ADMIN))
190                 return -EACCES;
191
192         if (sdp->type != TYPE_DISK)
193                 return -EINVAL;
194
195         sdp->allow_restart = simple_strtoul(buf, NULL, 10);
196
197         return count;
198 }
199
200 static ssize_t
201 sd_show_cache_type(struct device *dev, struct device_attribute *attr,
202                    char *buf)
203 {
204         struct scsi_disk *sdkp = to_scsi_disk(dev);
205         int ct = sdkp->RCD + 2*sdkp->WCE;
206
207         return snprintf(buf, 40, "%s\n", sd_cache_types[ct]);
208 }
209
210 static ssize_t
211 sd_show_fua(struct device *dev, struct device_attribute *attr, char *buf)
212 {
213         struct scsi_disk *sdkp = to_scsi_disk(dev);
214
215         return snprintf(buf, 20, "%u\n", sdkp->DPOFUA);
216 }
217
218 static ssize_t
219 sd_show_manage_start_stop(struct device *dev, struct device_attribute *attr,
220                           char *buf)
221 {
222         struct scsi_disk *sdkp = to_scsi_disk(dev);
223         struct scsi_device *sdp = sdkp->device;
224
225         return snprintf(buf, 20, "%u\n", sdp->manage_start_stop);
226 }
227
228 static ssize_t
229 sd_show_allow_restart(struct device *dev, struct device_attribute *attr,
230                       char *buf)
231 {
232         struct scsi_disk *sdkp = to_scsi_disk(dev);
233
234         return snprintf(buf, 40, "%d\n", sdkp->device->allow_restart);
235 }
236
237 static struct device_attribute sd_disk_attrs[] = {
238         __ATTR(cache_type, S_IRUGO|S_IWUSR, sd_show_cache_type,
239                sd_store_cache_type),
240         __ATTR(FUA, S_IRUGO, sd_show_fua, NULL),
241         __ATTR(allow_restart, S_IRUGO|S_IWUSR, sd_show_allow_restart,
242                sd_store_allow_restart),
243         __ATTR(manage_start_stop, S_IRUGO|S_IWUSR, sd_show_manage_start_stop,
244                sd_store_manage_start_stop),
245         __ATTR_NULL,
246 };
247
248 static struct class sd_disk_class = {
249         .name           = "scsi_disk",
250         .owner          = THIS_MODULE,
251         .dev_release    = scsi_disk_release,
252         .dev_attrs      = sd_disk_attrs,
253 };
254
255 static struct scsi_driver sd_template = {
256         .owner                  = THIS_MODULE,
257         .gendrv = {
258                 .name           = "sd",
259                 .probe          = sd_probe,
260                 .remove         = sd_remove,
261                 .suspend        = sd_suspend,
262                 .resume         = sd_resume,
263                 .shutdown       = sd_shutdown,
264         },
265         .rescan                 = sd_rescan,
266         .done                   = sd_done,
267 };
268
269 /*
270  * Device no to disk mapping:
271  * 
272  *       major         disc2     disc  p1
273  *   |............|.............|....|....| <- dev_t
274  *    31        20 19          8 7  4 3  0
275  * 
276  * Inside a major, we have 16k disks, however mapped non-
277  * contiguously. The first 16 disks are for major0, the next
278  * ones with major1, ... Disk 256 is for major0 again, disk 272 
279  * for major1, ... 
280  * As we stay compatible with our numbering scheme, we can reuse 
281  * the well-know SCSI majors 8, 65--71, 136--143.
282  */
283 static int sd_major(int major_idx)
284 {
285         switch (major_idx) {
286         case 0:
287                 return SCSI_DISK0_MAJOR;
288         case 1 ... 7:
289                 return SCSI_DISK1_MAJOR + major_idx - 1;
290         case 8 ... 15:
291                 return SCSI_DISK8_MAJOR + major_idx - 8;
292         default:
293                 BUG();
294                 return 0;       /* shut up gcc */
295         }
296 }
297
298 static inline struct scsi_disk *scsi_disk(struct gendisk *disk)
299 {
300         return container_of(disk->private_data, struct scsi_disk, driver);
301 }
302
303 static struct scsi_disk *__scsi_disk_get(struct gendisk *disk)
304 {
305         struct scsi_disk *sdkp = NULL;
306
307         if (disk->private_data) {
308                 sdkp = scsi_disk(disk);
309                 if (scsi_device_get(sdkp->device) == 0)
310                         get_device(&sdkp->dev);
311                 else
312                         sdkp = NULL;
313         }
314         return sdkp;
315 }
316
317 static struct scsi_disk *scsi_disk_get(struct gendisk *disk)
318 {
319         struct scsi_disk *sdkp;
320
321         mutex_lock(&sd_ref_mutex);
322         sdkp = __scsi_disk_get(disk);
323         mutex_unlock(&sd_ref_mutex);
324         return sdkp;
325 }
326
327 static struct scsi_disk *scsi_disk_get_from_dev(struct device *dev)
328 {
329         struct scsi_disk *sdkp;
330
331         mutex_lock(&sd_ref_mutex);
332         sdkp = dev_get_drvdata(dev);
333         if (sdkp)
334                 sdkp = __scsi_disk_get(sdkp->disk);
335         mutex_unlock(&sd_ref_mutex);
336         return sdkp;
337 }
338
339 static void scsi_disk_put(struct scsi_disk *sdkp)
340 {
341         struct scsi_device *sdev = sdkp->device;
342
343         mutex_lock(&sd_ref_mutex);
344         put_device(&sdkp->dev);
345         scsi_device_put(sdev);
346         mutex_unlock(&sd_ref_mutex);
347 }
348
349 /**
350  *      sd_init_command - build a scsi (read or write) command from
351  *      information in the request structure.
352  *      @SCpnt: pointer to mid-level's per scsi command structure that
353  *      contains request and into which the scsi command is written
354  *
355  *      Returns 1 if successful and 0 if error (or cannot be done now).
356  **/
357 static int sd_prep_fn(struct request_queue *q, struct request *rq)
358 {
359         struct scsi_cmnd *SCpnt;
360         struct scsi_device *sdp = q->queuedata;
361         struct gendisk *disk = rq->rq_disk;
362         sector_t block = rq->sector;
363         unsigned int this_count = rq->nr_sectors;
364         unsigned int timeout = sdp->timeout;
365         int ret;
366
367         if (rq->cmd_type == REQ_TYPE_BLOCK_PC) {
368                 ret = scsi_setup_blk_pc_cmnd(sdp, rq);
369                 goto out;
370         } else if (rq->cmd_type != REQ_TYPE_FS) {
371                 ret = BLKPREP_KILL;
372                 goto out;
373         }
374         ret = scsi_setup_fs_cmnd(sdp, rq);
375         if (ret != BLKPREP_OK)
376                 goto out;
377         SCpnt = rq->special;
378
379         /* from here on until we're complete, any goto out
380          * is used for a killable error condition */
381         ret = BLKPREP_KILL;
382
383         SCSI_LOG_HLQUEUE(1, scmd_printk(KERN_INFO, SCpnt,
384                                         "sd_init_command: block=%llu, "
385                                         "count=%d\n",
386                                         (unsigned long long)block,
387                                         this_count));
388
389         if (!sdp || !scsi_device_online(sdp) ||
390             block + rq->nr_sectors > get_capacity(disk)) {
391                 SCSI_LOG_HLQUEUE(2, scmd_printk(KERN_INFO, SCpnt,
392                                                 "Finishing %ld sectors\n",
393                                                 rq->nr_sectors));
394                 SCSI_LOG_HLQUEUE(2, scmd_printk(KERN_INFO, SCpnt,
395                                                 "Retry with 0x%p\n", SCpnt));
396                 goto out;
397         }
398
399         if (sdp->changed) {
400                 /*
401                  * quietly refuse to do anything to a changed disc until 
402                  * the changed bit has been reset
403                  */
404                 /* printk("SCSI disk has been changed. Prohibiting further I/O.\n"); */
405                 goto out;
406         }
407
408         /*
409          * Some devices (some sdcards for one) don't like it if the
410          * last sector gets read in a larger then 1 sector read.
411          */
412         if (unlikely(sdp->last_sector_bug &&
413             rq->nr_sectors > sdp->sector_size / 512 &&
414             block + this_count == get_capacity(disk)))
415                 this_count -= sdp->sector_size / 512;
416
417         SCSI_LOG_HLQUEUE(2, scmd_printk(KERN_INFO, SCpnt, "block=%llu\n",
418                                         (unsigned long long)block));
419
420         /*
421          * If we have a 1K hardware sectorsize, prevent access to single
422          * 512 byte sectors.  In theory we could handle this - in fact
423          * the scsi cdrom driver must be able to handle this because
424          * we typically use 1K blocksizes, and cdroms typically have
425          * 2K hardware sectorsizes.  Of course, things are simpler
426          * with the cdrom, since it is read-only.  For performance
427          * reasons, the filesystems should be able to handle this
428          * and not force the scsi disk driver to use bounce buffers
429          * for this.
430          */
431         if (sdp->sector_size == 1024) {
432                 if ((block & 1) || (rq->nr_sectors & 1)) {
433                         scmd_printk(KERN_ERR, SCpnt,
434                                     "Bad block number requested\n");
435                         goto out;
436                 } else {
437                         block = block >> 1;
438                         this_count = this_count >> 1;
439                 }
440         }
441         if (sdp->sector_size == 2048) {
442                 if ((block & 3) || (rq->nr_sectors & 3)) {
443                         scmd_printk(KERN_ERR, SCpnt,
444                                     "Bad block number requested\n");
445                         goto out;
446                 } else {
447                         block = block >> 2;
448                         this_count = this_count >> 2;
449                 }
450         }
451         if (sdp->sector_size == 4096) {
452                 if ((block & 7) || (rq->nr_sectors & 7)) {
453                         scmd_printk(KERN_ERR, SCpnt,
454                                     "Bad block number requested\n");
455                         goto out;
456                 } else {
457                         block = block >> 3;
458                         this_count = this_count >> 3;
459                 }
460         }
461         if (rq_data_dir(rq) == WRITE) {
462                 if (!sdp->writeable) {
463                         goto out;
464                 }
465                 SCpnt->cmnd[0] = WRITE_6;
466                 SCpnt->sc_data_direction = DMA_TO_DEVICE;
467         } else if (rq_data_dir(rq) == READ) {
468                 SCpnt->cmnd[0] = READ_6;
469                 SCpnt->sc_data_direction = DMA_FROM_DEVICE;
470         } else {
471                 scmd_printk(KERN_ERR, SCpnt, "Unknown command %x\n", rq->cmd_flags);
472                 goto out;
473         }
474
475         SCSI_LOG_HLQUEUE(2, scmd_printk(KERN_INFO, SCpnt,
476                                         "%s %d/%ld 512 byte blocks.\n",
477                                         (rq_data_dir(rq) == WRITE) ?
478                                         "writing" : "reading", this_count,
479                                         rq->nr_sectors));
480
481         SCpnt->cmnd[1] = 0;
482         
483         if (block > 0xffffffff) {
484                 SCpnt->cmnd[0] += READ_16 - READ_6;
485                 SCpnt->cmnd[1] |= blk_fua_rq(rq) ? 0x8 : 0;
486                 SCpnt->cmnd[2] = sizeof(block) > 4 ? (unsigned char) (block >> 56) & 0xff : 0;
487                 SCpnt->cmnd[3] = sizeof(block) > 4 ? (unsigned char) (block >> 48) & 0xff : 0;
488                 SCpnt->cmnd[4] = sizeof(block) > 4 ? (unsigned char) (block >> 40) & 0xff : 0;
489                 SCpnt->cmnd[5] = sizeof(block) > 4 ? (unsigned char) (block >> 32) & 0xff : 0;
490                 SCpnt->cmnd[6] = (unsigned char) (block >> 24) & 0xff;
491                 SCpnt->cmnd[7] = (unsigned char) (block >> 16) & 0xff;
492                 SCpnt->cmnd[8] = (unsigned char) (block >> 8) & 0xff;
493                 SCpnt->cmnd[9] = (unsigned char) block & 0xff;
494                 SCpnt->cmnd[10] = (unsigned char) (this_count >> 24) & 0xff;
495                 SCpnt->cmnd[11] = (unsigned char) (this_count >> 16) & 0xff;
496                 SCpnt->cmnd[12] = (unsigned char) (this_count >> 8) & 0xff;
497                 SCpnt->cmnd[13] = (unsigned char) this_count & 0xff;
498                 SCpnt->cmnd[14] = SCpnt->cmnd[15] = 0;
499         } else if ((this_count > 0xff) || (block > 0x1fffff) ||
500                    SCpnt->device->use_10_for_rw) {
501                 if (this_count > 0xffff)
502                         this_count = 0xffff;
503
504                 SCpnt->cmnd[0] += READ_10 - READ_6;
505                 SCpnt->cmnd[1] |= blk_fua_rq(rq) ? 0x8 : 0;
506                 SCpnt->cmnd[2] = (unsigned char) (block >> 24) & 0xff;
507                 SCpnt->cmnd[3] = (unsigned char) (block >> 16) & 0xff;
508                 SCpnt->cmnd[4] = (unsigned char) (block >> 8) & 0xff;
509                 SCpnt->cmnd[5] = (unsigned char) block & 0xff;
510                 SCpnt->cmnd[6] = SCpnt->cmnd[9] = 0;
511                 SCpnt->cmnd[7] = (unsigned char) (this_count >> 8) & 0xff;
512                 SCpnt->cmnd[8] = (unsigned char) this_count & 0xff;
513         } else {
514                 if (unlikely(blk_fua_rq(rq))) {
515                         /*
516                          * This happens only if this drive failed
517                          * 10byte rw command with ILLEGAL_REQUEST
518                          * during operation and thus turned off
519                          * use_10_for_rw.
520                          */
521                         scmd_printk(KERN_ERR, SCpnt,
522                                     "FUA write on READ/WRITE(6) drive\n");
523                         goto out;
524                 }
525
526                 SCpnt->cmnd[1] |= (unsigned char) ((block >> 16) & 0x1f);
527                 SCpnt->cmnd[2] = (unsigned char) ((block >> 8) & 0xff);
528                 SCpnt->cmnd[3] = (unsigned char) block & 0xff;
529                 SCpnt->cmnd[4] = (unsigned char) this_count;
530                 SCpnt->cmnd[5] = 0;
531         }
532         SCpnt->sdb.length = this_count * sdp->sector_size;
533
534         /*
535          * We shouldn't disconnect in the middle of a sector, so with a dumb
536          * host adapter, it's safe to assume that we can at least transfer
537          * this many bytes between each connect / disconnect.
538          */
539         SCpnt->transfersize = sdp->sector_size;
540         SCpnt->underflow = this_count << 9;
541         SCpnt->allowed = SD_MAX_RETRIES;
542         SCpnt->timeout_per_command = timeout;
543
544         /*
545          * This indicates that the command is ready from our end to be
546          * queued.
547          */
548         ret = BLKPREP_OK;
549  out:
550         return scsi_prep_return(q, rq, ret);
551 }
552
553 /**
554  *      sd_open - open a scsi disk device
555  *      @inode: only i_rdev member may be used
556  *      @filp: only f_mode and f_flags may be used
557  *
558  *      Returns 0 if successful. Returns a negated errno value in case 
559  *      of error.
560  *
561  *      Note: This can be called from a user context (e.g. fsck(1) )
562  *      or from within the kernel (e.g. as a result of a mount(1) ).
563  *      In the latter case @inode and @filp carry an abridged amount
564  *      of information as noted above.
565  **/
566 static int sd_open(struct inode *inode, struct file *filp)
567 {
568         struct gendisk *disk = inode->i_bdev->bd_disk;
569         struct scsi_disk *sdkp;
570         struct scsi_device *sdev;
571         int retval;
572
573         if (!(sdkp = scsi_disk_get(disk)))
574                 return -ENXIO;
575
576
577         SCSI_LOG_HLQUEUE(3, sd_printk(KERN_INFO, sdkp, "sd_open\n"));
578
579         sdev = sdkp->device;
580
581         /*
582          * If the device is in error recovery, wait until it is done.
583          * If the device is offline, then disallow any access to it.
584          */
585         retval = -ENXIO;
586         if (!scsi_block_when_processing_errors(sdev))
587                 goto error_out;
588
589         if (sdev->removable || sdkp->write_prot)
590                 check_disk_change(inode->i_bdev);
591
592         /*
593          * If the drive is empty, just let the open fail.
594          */
595         retval = -ENOMEDIUM;
596         if (sdev->removable && !sdkp->media_present &&
597             !(filp->f_flags & O_NDELAY))
598                 goto error_out;
599
600         /*
601          * If the device has the write protect tab set, have the open fail
602          * if the user expects to be able to write to the thing.
603          */
604         retval = -EROFS;
605         if (sdkp->write_prot && (filp->f_mode & FMODE_WRITE))
606                 goto error_out;
607
608         /*
609          * It is possible that the disk changing stuff resulted in
610          * the device being taken offline.  If this is the case,
611          * report this to the user, and don't pretend that the
612          * open actually succeeded.
613          */
614         retval = -ENXIO;
615         if (!scsi_device_online(sdev))
616                 goto error_out;
617
618         if (!sdkp->openers++ && sdev->removable) {
619                 if (scsi_block_when_processing_errors(sdev))
620                         scsi_set_medium_removal(sdev, SCSI_REMOVAL_PREVENT);
621         }
622
623         return 0;
624
625 error_out:
626         scsi_disk_put(sdkp);
627         return retval;  
628 }
629
630 /**
631  *      sd_release - invoked when the (last) close(2) is called on this
632  *      scsi disk.
633  *      @inode: only i_rdev member may be used
634  *      @filp: only f_mode and f_flags may be used
635  *
636  *      Returns 0. 
637  *
638  *      Note: may block (uninterruptible) if error recovery is underway
639  *      on this disk.
640  **/
641 static int sd_release(struct inode *inode, struct file *filp)
642 {
643         struct gendisk *disk = inode->i_bdev->bd_disk;
644         struct scsi_disk *sdkp = scsi_disk(disk);
645         struct scsi_device *sdev = sdkp->device;
646
647         SCSI_LOG_HLQUEUE(3, sd_printk(KERN_INFO, sdkp, "sd_release\n"));
648
649         if (!--sdkp->openers && sdev->removable) {
650                 if (scsi_block_when_processing_errors(sdev))
651                         scsi_set_medium_removal(sdev, SCSI_REMOVAL_ALLOW);
652         }
653
654         /*
655          * XXX and what if there are packets in flight and this close()
656          * XXX is followed by a "rmmod sd_mod"?
657          */
658         scsi_disk_put(sdkp);
659         return 0;
660 }
661
662 static int sd_getgeo(struct block_device *bdev, struct hd_geometry *geo)
663 {
664         struct scsi_disk *sdkp = scsi_disk(bdev->bd_disk);
665         struct scsi_device *sdp = sdkp->device;
666         struct Scsi_Host *host = sdp->host;
667         int diskinfo[4];
668
669         /* default to most commonly used values */
670         diskinfo[0] = 0x40;     /* 1 << 6 */
671         diskinfo[1] = 0x20;     /* 1 << 5 */
672         diskinfo[2] = sdkp->capacity >> 11;
673         
674         /* override with calculated, extended default, or driver values */
675         if (host->hostt->bios_param)
676                 host->hostt->bios_param(sdp, bdev, sdkp->capacity, diskinfo);
677         else
678                 scsicam_bios_param(bdev, sdkp->capacity, diskinfo);
679
680         geo->heads = diskinfo[0];
681         geo->sectors = diskinfo[1];
682         geo->cylinders = diskinfo[2];
683         return 0;
684 }
685
686 /**
687  *      sd_ioctl - process an ioctl
688  *      @inode: only i_rdev/i_bdev members may be used
689  *      @filp: only f_mode and f_flags may be used
690  *      @cmd: ioctl command number
691  *      @arg: this is third argument given to ioctl(2) system call.
692  *      Often contains a pointer.
693  *
694  *      Returns 0 if successful (some ioctls return postive numbers on
695  *      success as well). Returns a negated errno value in case of error.
696  *
697  *      Note: most ioctls are forward onto the block subsystem or further
698  *      down in the scsi subsystem.
699  **/
700 static int sd_ioctl(struct inode * inode, struct file * filp, 
701                     unsigned int cmd, unsigned long arg)
702 {
703         struct block_device *bdev = inode->i_bdev;
704         struct gendisk *disk = bdev->bd_disk;
705         struct scsi_device *sdp = scsi_disk(disk)->device;
706         void __user *p = (void __user *)arg;
707         int error;
708     
709         SCSI_LOG_IOCTL(1, printk("sd_ioctl: disk=%s, cmd=0x%x\n",
710                                                 disk->disk_name, cmd));
711
712         /*
713          * If we are in the middle of error recovery, don't let anyone
714          * else try and use this device.  Also, if error recovery fails, it
715          * may try and take the device offline, in which case all further
716          * access to the device is prohibited.
717          */
718         error = scsi_nonblockable_ioctl(sdp, cmd, p, filp);
719         if (!scsi_block_when_processing_errors(sdp) || !error)
720                 return error;
721
722         /*
723          * Send SCSI addressing ioctls directly to mid level, send other
724          * ioctls to block level and then onto mid level if they can't be
725          * resolved.
726          */
727         switch (cmd) {
728                 case SCSI_IOCTL_GET_IDLUN:
729                 case SCSI_IOCTL_GET_BUS_NUMBER:
730                         return scsi_ioctl(sdp, cmd, p);
731                 default:
732                         error = scsi_cmd_ioctl(filp, disk->queue, disk, cmd, p);
733                         if (error != -ENOTTY)
734                                 return error;
735         }
736         return scsi_ioctl(sdp, cmd, p);
737 }
738
739 static void set_media_not_present(struct scsi_disk *sdkp)
740 {
741         sdkp->media_present = 0;
742         sdkp->capacity = 0;
743         sdkp->device->changed = 1;
744 }
745
746 /**
747  *      sd_media_changed - check if our medium changed
748  *      @disk: kernel device descriptor 
749  *
750  *      Returns 0 if not applicable or no change; 1 if change
751  *
752  *      Note: this function is invoked from the block subsystem.
753  **/
754 static int sd_media_changed(struct gendisk *disk)
755 {
756         struct scsi_disk *sdkp = scsi_disk(disk);
757         struct scsi_device *sdp = sdkp->device;
758         struct scsi_sense_hdr *sshdr = NULL;
759         int retval;
760
761         SCSI_LOG_HLQUEUE(3, sd_printk(KERN_INFO, sdkp, "sd_media_changed\n"));
762
763         if (!sdp->removable)
764                 return 0;
765
766         /*
767          * If the device is offline, don't send any commands - just pretend as
768          * if the command failed.  If the device ever comes back online, we
769          * can deal with it then.  It is only because of unrecoverable errors
770          * that we would ever take a device offline in the first place.
771          */
772         if (!scsi_device_online(sdp)) {
773                 set_media_not_present(sdkp);
774                 retval = 1;
775                 goto out;
776         }
777
778         /*
779          * Using TEST_UNIT_READY enables differentiation between drive with
780          * no cartridge loaded - NOT READY, drive with changed cartridge -
781          * UNIT ATTENTION, or with same cartridge - GOOD STATUS.
782          *
783          * Drives that auto spin down. eg iomega jaz 1G, will be started
784          * by sd_spinup_disk() from sd_revalidate_disk(), which happens whenever
785          * sd_revalidate() is called.
786          */
787         retval = -ENODEV;
788
789         if (scsi_block_when_processing_errors(sdp)) {
790                 sshdr  = kzalloc(sizeof(*sshdr), GFP_KERNEL);
791                 retval = scsi_test_unit_ready(sdp, SD_TIMEOUT, SD_MAX_RETRIES,
792                                               sshdr);
793         }
794
795         /*
796          * Unable to test, unit probably not ready.   This usually
797          * means there is no disc in the drive.  Mark as changed,
798          * and we will figure it out later once the drive is
799          * available again.
800          */
801         if (retval || (scsi_sense_valid(sshdr) &&
802                        /* 0x3a is medium not present */
803                        sshdr->asc == 0x3a)) {
804                 set_media_not_present(sdkp);
805                 retval = 1;
806                 goto out;
807         }
808
809         /*
810          * For removable scsi disk we have to recognise the presence
811          * of a disk in the drive. This is kept in the struct scsi_disk
812          * struct and tested at open !  Daniel Roche (dan@lectra.fr)
813          */
814         sdkp->media_present = 1;
815
816         retval = sdp->changed;
817         sdp->changed = 0;
818 out:
819         if (retval != sdkp->previous_state)
820                 sdev_evt_send_simple(sdp, SDEV_EVT_MEDIA_CHANGE, GFP_KERNEL);
821         sdkp->previous_state = retval;
822         kfree(sshdr);
823         return retval;
824 }
825
826 static int sd_sync_cache(struct scsi_disk *sdkp)
827 {
828         int retries, res;
829         struct scsi_device *sdp = sdkp->device;
830         struct scsi_sense_hdr sshdr;
831
832         if (!scsi_device_online(sdp))
833                 return -ENODEV;
834
835
836         for (retries = 3; retries > 0; --retries) {
837                 unsigned char cmd[10] = { 0 };
838
839                 cmd[0] = SYNCHRONIZE_CACHE;
840                 /*
841                  * Leave the rest of the command zero to indicate
842                  * flush everything.
843                  */
844                 res = scsi_execute_req(sdp, cmd, DMA_NONE, NULL, 0, &sshdr,
845                                        SD_TIMEOUT, SD_MAX_RETRIES);
846                 if (res == 0)
847                         break;
848         }
849
850         if (res) {
851                 sd_print_result(sdkp, res);
852                 if (driver_byte(res) & DRIVER_SENSE)
853                         sd_print_sense_hdr(sdkp, &sshdr);
854         }
855
856         if (res)
857                 return -EIO;
858         return 0;
859 }
860
861 static void sd_prepare_flush(struct request_queue *q, struct request *rq)
862 {
863         memset(rq->cmd, 0, sizeof(rq->cmd));
864         rq->cmd_type = REQ_TYPE_BLOCK_PC;
865         rq->timeout = SD_TIMEOUT;
866         rq->cmd[0] = SYNCHRONIZE_CACHE;
867         rq->cmd_len = 10;
868 }
869
870 static void sd_rescan(struct device *dev)
871 {
872         struct scsi_disk *sdkp = scsi_disk_get_from_dev(dev);
873
874         if (sdkp) {
875                 sd_revalidate_disk(sdkp->disk);
876                 scsi_disk_put(sdkp);
877         }
878 }
879
880
881 #ifdef CONFIG_COMPAT
882 /* 
883  * This gets directly called from VFS. When the ioctl 
884  * is not recognized we go back to the other translation paths. 
885  */
886 static long sd_compat_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
887 {
888         struct block_device *bdev = file->f_path.dentry->d_inode->i_bdev;
889         struct gendisk *disk = bdev->bd_disk;
890         struct scsi_device *sdev = scsi_disk(disk)->device;
891
892         /*
893          * If we are in the middle of error recovery, don't let anyone
894          * else try and use this device.  Also, if error recovery fails, it
895          * may try and take the device offline, in which case all further
896          * access to the device is prohibited.
897          */
898         if (!scsi_block_when_processing_errors(sdev))
899                 return -ENODEV;
900                
901         if (sdev->host->hostt->compat_ioctl) {
902                 int ret;
903
904                 ret = sdev->host->hostt->compat_ioctl(sdev, cmd, (void __user *)arg);
905
906                 return ret;
907         }
908
909         /* 
910          * Let the static ioctl translation table take care of it.
911          */
912         return -ENOIOCTLCMD; 
913 }
914 #endif
915
916 static struct block_device_operations sd_fops = {
917         .owner                  = THIS_MODULE,
918         .open                   = sd_open,
919         .release                = sd_release,
920         .ioctl                  = sd_ioctl,
921         .getgeo                 = sd_getgeo,
922 #ifdef CONFIG_COMPAT
923         .compat_ioctl           = sd_compat_ioctl,
924 #endif
925         .media_changed          = sd_media_changed,
926         .revalidate_disk        = sd_revalidate_disk,
927 };
928
929 /**
930  *      sd_done - bottom half handler: called when the lower level
931  *      driver has completed (successfully or otherwise) a scsi command.
932  *      @SCpnt: mid-level's per command structure.
933  *
934  *      Note: potentially run from within an ISR. Must not block.
935  **/
936 static int sd_done(struct scsi_cmnd *SCpnt)
937 {
938         int result = SCpnt->result;
939         unsigned int xfer_size = scsi_bufflen(SCpnt);
940         unsigned int good_bytes = result ? 0 : xfer_size;
941         u64 start_lba = SCpnt->request->sector;
942         u64 end_lba = SCpnt->request->sector + (xfer_size / 512);
943         u64 bad_lba;
944         struct scsi_sense_hdr sshdr;
945         int sense_valid = 0;
946         int sense_deferred = 0;
947         int info_valid;
948
949         if (result) {
950                 sense_valid = scsi_command_normalize_sense(SCpnt, &sshdr);
951                 if (sense_valid)
952                         sense_deferred = scsi_sense_is_deferred(&sshdr);
953         }
954 #ifdef CONFIG_SCSI_LOGGING
955         SCSI_LOG_HLCOMPLETE(1, scsi_print_result(SCpnt));
956         if (sense_valid) {
957                 SCSI_LOG_HLCOMPLETE(1, scmd_printk(KERN_INFO, SCpnt,
958                                                    "sd_done: sb[respc,sk,asc,"
959                                                    "ascq]=%x,%x,%x,%x\n",
960                                                    sshdr.response_code,
961                                                    sshdr.sense_key, sshdr.asc,
962                                                    sshdr.ascq));
963         }
964 #endif
965         if (driver_byte(result) != DRIVER_SENSE &&
966             (!sense_valid || sense_deferred))
967                 goto out;
968
969         switch (sshdr.sense_key) {
970         case HARDWARE_ERROR:
971         case MEDIUM_ERROR:
972                 if (!blk_fs_request(SCpnt->request))
973                         goto out;
974                 info_valid = scsi_get_sense_info_fld(SCpnt->sense_buffer,
975                                                      SCSI_SENSE_BUFFERSIZE,
976                                                      &bad_lba);
977                 if (!info_valid)
978                         goto out;
979                 if (xfer_size <= SCpnt->device->sector_size)
980                         goto out;
981                 if (SCpnt->device->sector_size < 512) {
982                         /* only legitimate sector_size here is 256 */
983                         start_lba <<= 1;
984                         end_lba <<= 1;
985                 } else {
986                         /* be careful ... don't want any overflows */
987                         u64 factor = SCpnt->device->sector_size / 512;
988                         do_div(start_lba, factor);
989                         do_div(end_lba, factor);
990                 }
991
992                 if (bad_lba < start_lba  || bad_lba >= end_lba)
993                         /* the bad lba was reported incorrectly, we have
994                          * no idea where the error is
995                          */
996                         goto out;
997
998                 /* This computation should always be done in terms of
999                  * the resolution of the device's medium.
1000                  */
1001                 good_bytes = (bad_lba - start_lba)*SCpnt->device->sector_size;
1002                 break;
1003         case RECOVERED_ERROR:
1004         case NO_SENSE:
1005                 /* Inform the user, but make sure that it's not treated
1006                  * as a hard error.
1007                  */
1008                 scsi_print_sense("sd", SCpnt);
1009                 SCpnt->result = 0;
1010                 memset(SCpnt->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE);
1011                 good_bytes = xfer_size;
1012                 break;
1013         case ILLEGAL_REQUEST:
1014                 if (SCpnt->device->use_10_for_rw &&
1015                     (SCpnt->cmnd[0] == READ_10 ||
1016                      SCpnt->cmnd[0] == WRITE_10))
1017                         SCpnt->device->use_10_for_rw = 0;
1018                 if (SCpnt->device->use_10_for_ms &&
1019                     (SCpnt->cmnd[0] == MODE_SENSE_10 ||
1020                      SCpnt->cmnd[0] == MODE_SELECT_10))
1021                         SCpnt->device->use_10_for_ms = 0;
1022                 break;
1023         default:
1024                 break;
1025         }
1026  out:
1027         return good_bytes;
1028 }
1029
1030 static int media_not_present(struct scsi_disk *sdkp,
1031                              struct scsi_sense_hdr *sshdr)
1032 {
1033
1034         if (!scsi_sense_valid(sshdr))
1035                 return 0;
1036         /* not invoked for commands that could return deferred errors */
1037         if (sshdr->sense_key != NOT_READY &&
1038             sshdr->sense_key != UNIT_ATTENTION)
1039                 return 0;
1040         if (sshdr->asc != 0x3A) /* medium not present */
1041                 return 0;
1042
1043         set_media_not_present(sdkp);
1044         return 1;
1045 }
1046
1047 /*
1048  * spinup disk - called only in sd_revalidate_disk()
1049  */
1050 static void
1051 sd_spinup_disk(struct scsi_disk *sdkp)
1052 {
1053         unsigned char cmd[10];
1054         unsigned long spintime_expire = 0;
1055         int retries, spintime;
1056         unsigned int the_result;
1057         struct scsi_sense_hdr sshdr;
1058         int sense_valid = 0;
1059
1060         spintime = 0;
1061
1062         /* Spin up drives, as required.  Only do this at boot time */
1063         /* Spinup needs to be done for module loads too. */
1064         do {
1065                 retries = 0;
1066
1067                 do {
1068                         cmd[0] = TEST_UNIT_READY;
1069                         memset((void *) &cmd[1], 0, 9);
1070
1071                         the_result = scsi_execute_req(sdkp->device, cmd,
1072                                                       DMA_NONE, NULL, 0,
1073                                                       &sshdr, SD_TIMEOUT,
1074                                                       SD_MAX_RETRIES);
1075
1076                         /*
1077                          * If the drive has indicated to us that it
1078                          * doesn't have any media in it, don't bother
1079                          * with any more polling.
1080                          */
1081                         if (media_not_present(sdkp, &sshdr))
1082                                 return;
1083
1084                         if (the_result)
1085                                 sense_valid = scsi_sense_valid(&sshdr);
1086                         retries++;
1087                 } while (retries < 3 && 
1088                          (!scsi_status_is_good(the_result) ||
1089                           ((driver_byte(the_result) & DRIVER_SENSE) &&
1090                           sense_valid && sshdr.sense_key == UNIT_ATTENTION)));
1091
1092                 if ((driver_byte(the_result) & DRIVER_SENSE) == 0) {
1093                         /* no sense, TUR either succeeded or failed
1094                          * with a status error */
1095                         if(!spintime && !scsi_status_is_good(the_result)) {
1096                                 sd_printk(KERN_NOTICE, sdkp, "Unit Not Ready\n");
1097                                 sd_print_result(sdkp, the_result);
1098                         }
1099                         break;
1100                 }
1101                                         
1102                 /*
1103                  * The device does not want the automatic start to be issued.
1104                  */
1105                 if (sdkp->device->no_start_on_add) {
1106                         break;
1107                 }
1108
1109                 /*
1110                  * If manual intervention is required, or this is an
1111                  * absent USB storage device, a spinup is meaningless.
1112                  */
1113                 if (sense_valid &&
1114                     sshdr.sense_key == NOT_READY &&
1115                     sshdr.asc == 4 && sshdr.ascq == 3) {
1116                         break;          /* manual intervention required */
1117
1118                 /*
1119                  * Issue command to spin up drive when not ready
1120                  */
1121                 } else if (sense_valid && sshdr.sense_key == NOT_READY) {
1122                         if (!spintime) {
1123                                 sd_printk(KERN_NOTICE, sdkp, "Spinning up disk...");
1124                                 cmd[0] = START_STOP;
1125                                 cmd[1] = 1;     /* Return immediately */
1126                                 memset((void *) &cmd[2], 0, 8);
1127                                 cmd[4] = 1;     /* Start spin cycle */
1128                                 scsi_execute_req(sdkp->device, cmd, DMA_NONE,
1129                                                  NULL, 0, &sshdr,
1130                                                  SD_TIMEOUT, SD_MAX_RETRIES);
1131                                 spintime_expire = jiffies + 100 * HZ;
1132                                 spintime = 1;
1133                         }
1134                         /* Wait 1 second for next try */
1135                         msleep(1000);
1136                         printk(".");
1137
1138                 /*
1139                  * Wait for USB flash devices with slow firmware.
1140                  * Yes, this sense key/ASC combination shouldn't
1141                  * occur here.  It's characteristic of these devices.
1142                  */
1143                 } else if (sense_valid &&
1144                                 sshdr.sense_key == UNIT_ATTENTION &&
1145                                 sshdr.asc == 0x28) {
1146                         if (!spintime) {
1147                                 spintime_expire = jiffies + 5 * HZ;
1148                                 spintime = 1;
1149                         }
1150                         /* Wait 1 second for next try */
1151                         msleep(1000);
1152                 } else {
1153                         /* we don't understand the sense code, so it's
1154                          * probably pointless to loop */
1155                         if(!spintime) {
1156                                 sd_printk(KERN_NOTICE, sdkp, "Unit Not Ready\n");
1157                                 sd_print_sense_hdr(sdkp, &sshdr);
1158                         }
1159                         break;
1160                 }
1161                                 
1162         } while (spintime && time_before_eq(jiffies, spintime_expire));
1163
1164         if (spintime) {
1165                 if (scsi_status_is_good(the_result))
1166                         printk("ready\n");
1167                 else
1168                         printk("not responding...\n");
1169         }
1170 }
1171
1172 /*
1173  * read disk capacity
1174  */
1175 static void
1176 sd_read_capacity(struct scsi_disk *sdkp, unsigned char *buffer)
1177 {
1178         unsigned char cmd[16];
1179         int the_result, retries;
1180         int sector_size = 0;
1181         int longrc = 0;
1182         struct scsi_sense_hdr sshdr;
1183         int sense_valid = 0;
1184         struct scsi_device *sdp = sdkp->device;
1185
1186 repeat:
1187         retries = 3;
1188         do {
1189                 if (longrc) {
1190                         memset((void *) cmd, 0, 16);
1191                         cmd[0] = SERVICE_ACTION_IN;
1192                         cmd[1] = SAI_READ_CAPACITY_16;
1193                         cmd[13] = 12;
1194                         memset((void *) buffer, 0, 12);
1195                 } else {
1196                         cmd[0] = READ_CAPACITY;
1197                         memset((void *) &cmd[1], 0, 9);
1198                         memset((void *) buffer, 0, 8);
1199                 }
1200                 
1201                 the_result = scsi_execute_req(sdp, cmd, DMA_FROM_DEVICE,
1202                                               buffer, longrc ? 12 : 8, &sshdr,
1203                                               SD_TIMEOUT, SD_MAX_RETRIES);
1204
1205                 if (media_not_present(sdkp, &sshdr))
1206                         return;
1207
1208                 if (the_result)
1209                         sense_valid = scsi_sense_valid(&sshdr);
1210                 retries--;
1211
1212         } while (the_result && retries);
1213
1214         if (the_result && !longrc) {
1215                 sd_printk(KERN_NOTICE, sdkp, "READ CAPACITY failed\n");
1216                 sd_print_result(sdkp, the_result);
1217                 if (driver_byte(the_result) & DRIVER_SENSE)
1218                         sd_print_sense_hdr(sdkp, &sshdr);
1219                 else
1220                         sd_printk(KERN_NOTICE, sdkp, "Sense not available.\n");
1221
1222                 /* Set dirty bit for removable devices if not ready -
1223                  * sometimes drives will not report this properly. */
1224                 if (sdp->removable &&
1225                     sense_valid && sshdr.sense_key == NOT_READY)
1226                         sdp->changed = 1;
1227
1228                 /* Either no media are present but the drive didn't tell us,
1229                    or they are present but the read capacity command fails */
1230                 /* sdkp->media_present = 0; -- not always correct */
1231                 sdkp->capacity = 0; /* unknown mapped to zero - as usual */
1232
1233                 return;
1234         } else if (the_result && longrc) {
1235                 /* READ CAPACITY(16) has been failed */
1236                 sd_printk(KERN_NOTICE, sdkp, "READ CAPACITY(16) failed\n");
1237                 sd_print_result(sdkp, the_result);
1238                 sd_printk(KERN_NOTICE, sdkp, "Use 0xffffffff as device size\n");
1239
1240                 sdkp->capacity = 1 + (sector_t) 0xffffffff;             
1241                 goto got_data;
1242         }       
1243         
1244         if (!longrc) {
1245                 sector_size = (buffer[4] << 24) |
1246                         (buffer[5] << 16) | (buffer[6] << 8) | buffer[7];
1247                 if (buffer[0] == 0xff && buffer[1] == 0xff &&
1248                     buffer[2] == 0xff && buffer[3] == 0xff) {
1249                         if(sizeof(sdkp->capacity) > 4) {
1250                                 sd_printk(KERN_NOTICE, sdkp, "Very big device. "
1251                                           "Trying to use READ CAPACITY(16).\n");
1252                                 longrc = 1;
1253                                 goto repeat;
1254                         }
1255                         sd_printk(KERN_ERR, sdkp, "Too big for this kernel. Use "
1256                                   "a kernel compiled with support for large "
1257                                   "block devices.\n");
1258                         sdkp->capacity = 0;
1259                         goto got_data;
1260                 }
1261                 sdkp->capacity = 1 + (((sector_t)buffer[0] << 24) |
1262                         (buffer[1] << 16) |
1263                         (buffer[2] << 8) |
1264                         buffer[3]);                     
1265         } else {
1266                 sdkp->capacity = 1 + (((u64)buffer[0] << 56) |
1267                         ((u64)buffer[1] << 48) |
1268                         ((u64)buffer[2] << 40) |
1269                         ((u64)buffer[3] << 32) |
1270                         ((sector_t)buffer[4] << 24) |
1271                         ((sector_t)buffer[5] << 16) |
1272                         ((sector_t)buffer[6] << 8)  |
1273                         (sector_t)buffer[7]);
1274                         
1275                 sector_size = (buffer[8] << 24) |
1276                         (buffer[9] << 16) | (buffer[10] << 8) | buffer[11];
1277         }       
1278
1279         /* Some devices return the total number of sectors, not the
1280          * highest sector number.  Make the necessary adjustment. */
1281         if (sdp->fix_capacity) {
1282                 --sdkp->capacity;
1283
1284         /* Some devices have version which report the correct sizes
1285          * and others which do not. We guess size according to a heuristic
1286          * and err on the side of lowering the capacity. */
1287         } else {
1288                 if (sdp->guess_capacity)
1289                         if (sdkp->capacity & 0x01) /* odd sizes are odd */
1290                                 --sdkp->capacity;
1291         }
1292
1293 got_data:
1294         if (sector_size == 0) {
1295                 sector_size = 512;
1296                 sd_printk(KERN_NOTICE, sdkp, "Sector size 0 reported, "
1297                           "assuming 512.\n");
1298         }
1299
1300         if (sector_size != 512 &&
1301             sector_size != 1024 &&
1302             sector_size != 2048 &&
1303             sector_size != 4096 &&
1304             sector_size != 256) {
1305                 sd_printk(KERN_NOTICE, sdkp, "Unsupported sector size %d.\n",
1306                           sector_size);
1307                 /*
1308                  * The user might want to re-format the drive with
1309                  * a supported sectorsize.  Once this happens, it
1310                  * would be relatively trivial to set the thing up.
1311                  * For this reason, we leave the thing in the table.
1312                  */
1313                 sdkp->capacity = 0;
1314                 /*
1315                  * set a bogus sector size so the normal read/write
1316                  * logic in the block layer will eventually refuse any
1317                  * request on this device without tripping over power
1318                  * of two sector size assumptions
1319                  */
1320                 sector_size = 512;
1321         }
1322         {
1323                 /*
1324                  * The msdos fs needs to know the hardware sector size
1325                  * So I have created this table. See ll_rw_blk.c
1326                  * Jacques Gelinas (Jacques@solucorp.qc.ca)
1327                  */
1328                 int hard_sector = sector_size;
1329                 sector_t sz = (sdkp->capacity/2) * (hard_sector/256);
1330                 struct request_queue *queue = sdp->request_queue;
1331                 sector_t mb = sz;
1332
1333                 blk_queue_hardsect_size(queue, hard_sector);
1334                 /* avoid 64-bit division on 32-bit platforms */
1335                 sector_div(sz, 625);
1336                 mb -= sz - 974;
1337                 sector_div(mb, 1950);
1338
1339                 sd_printk(KERN_NOTICE, sdkp,
1340                           "%llu %d-byte hardware sectors (%llu MB)\n",
1341                           (unsigned long long)sdkp->capacity,
1342                           hard_sector, (unsigned long long)mb);
1343         }
1344
1345         /* Rescale capacity to 512-byte units */
1346         if (sector_size == 4096)
1347                 sdkp->capacity <<= 3;
1348         else if (sector_size == 2048)
1349                 sdkp->capacity <<= 2;
1350         else if (sector_size == 1024)
1351                 sdkp->capacity <<= 1;
1352         else if (sector_size == 256)
1353                 sdkp->capacity >>= 1;
1354
1355         sdkp->device->sector_size = sector_size;
1356 }
1357
1358 /* called with buffer of length 512 */
1359 static inline int
1360 sd_do_mode_sense(struct scsi_device *sdp, int dbd, int modepage,
1361                  unsigned char *buffer, int len, struct scsi_mode_data *data,
1362                  struct scsi_sense_hdr *sshdr)
1363 {
1364         return scsi_mode_sense(sdp, dbd, modepage, buffer, len,
1365                                SD_TIMEOUT, SD_MAX_RETRIES, data,
1366                                sshdr);
1367 }
1368
1369 /*
1370  * read write protect setting, if possible - called only in sd_revalidate_disk()
1371  * called with buffer of length SD_BUF_SIZE
1372  */
1373 static void
1374 sd_read_write_protect_flag(struct scsi_disk *sdkp, unsigned char *buffer)
1375 {
1376         int res;
1377         struct scsi_device *sdp = sdkp->device;
1378         struct scsi_mode_data data;
1379
1380         set_disk_ro(sdkp->disk, 0);
1381         if (sdp->skip_ms_page_3f) {
1382                 sd_printk(KERN_NOTICE, sdkp, "Assuming Write Enabled\n");
1383                 return;
1384         }
1385
1386         if (sdp->use_192_bytes_for_3f) {
1387                 res = sd_do_mode_sense(sdp, 0, 0x3F, buffer, 192, &data, NULL);
1388         } else {
1389                 /*
1390                  * First attempt: ask for all pages (0x3F), but only 4 bytes.
1391                  * We have to start carefully: some devices hang if we ask
1392                  * for more than is available.
1393                  */
1394                 res = sd_do_mode_sense(sdp, 0, 0x3F, buffer, 4, &data, NULL);
1395
1396                 /*
1397                  * Second attempt: ask for page 0 When only page 0 is
1398                  * implemented, a request for page 3F may return Sense Key
1399                  * 5: Illegal Request, Sense Code 24: Invalid field in
1400                  * CDB.
1401                  */
1402                 if (!scsi_status_is_good(res))
1403                         res = sd_do_mode_sense(sdp, 0, 0, buffer, 4, &data, NULL);
1404
1405                 /*
1406                  * Third attempt: ask 255 bytes, as we did earlier.
1407                  */
1408                 if (!scsi_status_is_good(res))
1409                         res = sd_do_mode_sense(sdp, 0, 0x3F, buffer, 255,
1410                                                &data, NULL);
1411         }
1412
1413         if (!scsi_status_is_good(res)) {
1414                 sd_printk(KERN_WARNING, sdkp,
1415                           "Test WP failed, assume Write Enabled\n");
1416         } else {
1417                 sdkp->write_prot = ((data.device_specific & 0x80) != 0);
1418                 set_disk_ro(sdkp->disk, sdkp->write_prot);
1419                 sd_printk(KERN_NOTICE, sdkp, "Write Protect is %s\n",
1420                           sdkp->write_prot ? "on" : "off");
1421                 sd_printk(KERN_DEBUG, sdkp,
1422                           "Mode Sense: %02x %02x %02x %02x\n",
1423                           buffer[0], buffer[1], buffer[2], buffer[3]);
1424         }
1425 }
1426
1427 /*
1428  * sd_read_cache_type - called only from sd_revalidate_disk()
1429  * called with buffer of length SD_BUF_SIZE
1430  */
1431 static void
1432 sd_read_cache_type(struct scsi_disk *sdkp, unsigned char *buffer)
1433 {
1434         int len = 0, res;
1435         struct scsi_device *sdp = sdkp->device;
1436
1437         int dbd;
1438         int modepage;
1439         struct scsi_mode_data data;
1440         struct scsi_sense_hdr sshdr;
1441
1442         if (sdp->skip_ms_page_8)
1443                 goto defaults;
1444
1445         if (sdp->type == TYPE_RBC) {
1446                 modepage = 6;
1447                 dbd = 8;
1448         } else {
1449                 modepage = 8;
1450                 dbd = 0;
1451         }
1452
1453         /* cautiously ask */
1454         res = sd_do_mode_sense(sdp, dbd, modepage, buffer, 4, &data, &sshdr);
1455
1456         if (!scsi_status_is_good(res))
1457                 goto bad_sense;
1458
1459         if (!data.header_length) {
1460                 modepage = 6;
1461                 sd_printk(KERN_ERR, sdkp, "Missing header in MODE_SENSE response\n");
1462         }
1463
1464         /* that went OK, now ask for the proper length */
1465         len = data.length;
1466
1467         /*
1468          * We're only interested in the first three bytes, actually.
1469          * But the data cache page is defined for the first 20.
1470          */
1471         if (len < 3)
1472                 goto bad_sense;
1473         if (len > 20)
1474                 len = 20;
1475
1476         /* Take headers and block descriptors into account */
1477         len += data.header_length + data.block_descriptor_length;
1478         if (len > SD_BUF_SIZE)
1479                 goto bad_sense;
1480
1481         /* Get the data */
1482         res = sd_do_mode_sense(sdp, dbd, modepage, buffer, len, &data, &sshdr);
1483
1484         if (scsi_status_is_good(res)) {
1485                 int offset = data.header_length + data.block_descriptor_length;
1486
1487                 if (offset >= SD_BUF_SIZE - 2) {
1488                         sd_printk(KERN_ERR, sdkp, "Malformed MODE SENSE response\n");
1489                         goto defaults;
1490                 }
1491
1492                 if ((buffer[offset] & 0x3f) != modepage) {
1493                         sd_printk(KERN_ERR, sdkp, "Got wrong page\n");
1494                         goto defaults;
1495                 }
1496
1497                 if (modepage == 8) {
1498                         sdkp->WCE = ((buffer[offset + 2] & 0x04) != 0);
1499                         sdkp->RCD = ((buffer[offset + 2] & 0x01) != 0);
1500                 } else {
1501                         sdkp->WCE = ((buffer[offset + 2] & 0x01) == 0);
1502                         sdkp->RCD = 0;
1503                 }
1504
1505                 sdkp->DPOFUA = (data.device_specific & 0x10) != 0;
1506                 if (sdkp->DPOFUA && !sdkp->device->use_10_for_rw) {
1507                         sd_printk(KERN_NOTICE, sdkp,
1508                                   "Uses READ/WRITE(6), disabling FUA\n");
1509                         sdkp->DPOFUA = 0;
1510                 }
1511
1512                 sd_printk(KERN_NOTICE, sdkp,
1513                        "Write cache: %s, read cache: %s, %s\n",
1514                        sdkp->WCE ? "enabled" : "disabled",
1515                        sdkp->RCD ? "disabled" : "enabled",
1516                        sdkp->DPOFUA ? "supports DPO and FUA"
1517                        : "doesn't support DPO or FUA");
1518
1519                 return;
1520         }
1521
1522 bad_sense:
1523         if (scsi_sense_valid(&sshdr) &&
1524             sshdr.sense_key == ILLEGAL_REQUEST &&
1525             sshdr.asc == 0x24 && sshdr.ascq == 0x0)
1526                 /* Invalid field in CDB */
1527                 sd_printk(KERN_NOTICE, sdkp, "Cache data unavailable\n");
1528         else
1529                 sd_printk(KERN_ERR, sdkp, "Asking for cache data failed\n");
1530
1531 defaults:
1532         sd_printk(KERN_ERR, sdkp, "Assuming drive cache: write through\n");
1533         sdkp->WCE = 0;
1534         sdkp->RCD = 0;
1535         sdkp->DPOFUA = 0;
1536 }
1537
1538 /**
1539  *      sd_revalidate_disk - called the first time a new disk is seen,
1540  *      performs disk spin up, read_capacity, etc.
1541  *      @disk: struct gendisk we care about
1542  **/
1543 static int sd_revalidate_disk(struct gendisk *disk)
1544 {
1545         struct scsi_disk *sdkp = scsi_disk(disk);
1546         struct scsi_device *sdp = sdkp->device;
1547         unsigned char *buffer;
1548         unsigned ordered;
1549
1550         SCSI_LOG_HLQUEUE(3, sd_printk(KERN_INFO, sdkp,
1551                                       "sd_revalidate_disk\n"));
1552
1553         /*
1554          * If the device is offline, don't try and read capacity or any
1555          * of the other niceties.
1556          */
1557         if (!scsi_device_online(sdp))
1558                 goto out;
1559
1560         buffer = kmalloc(SD_BUF_SIZE, GFP_KERNEL);
1561         if (!buffer) {
1562                 sd_printk(KERN_WARNING, sdkp, "sd_revalidate_disk: Memory "
1563                           "allocation failure.\n");
1564                 goto out;
1565         }
1566
1567         /* defaults, until the device tells us otherwise */
1568         sdp->sector_size = 512;
1569         sdkp->capacity = 0;
1570         sdkp->media_present = 1;
1571         sdkp->write_prot = 0;
1572         sdkp->WCE = 0;
1573         sdkp->RCD = 0;
1574
1575         sd_spinup_disk(sdkp);
1576
1577         /*
1578          * Without media there is no reason to ask; moreover, some devices
1579          * react badly if we do.
1580          */
1581         if (sdkp->media_present) {
1582                 sd_read_capacity(sdkp, buffer);
1583                 sd_read_write_protect_flag(sdkp, buffer);
1584                 sd_read_cache_type(sdkp, buffer);
1585         }
1586
1587         /*
1588          * We now have all cache related info, determine how we deal
1589          * with ordered requests.  Note that as the current SCSI
1590          * dispatch function can alter request order, we cannot use
1591          * QUEUE_ORDERED_TAG_* even when ordered tag is supported.
1592          */
1593         if (sdkp->WCE)
1594                 ordered = sdkp->DPOFUA
1595                         ? QUEUE_ORDERED_DRAIN_FUA : QUEUE_ORDERED_DRAIN_FLUSH;
1596         else
1597                 ordered = QUEUE_ORDERED_DRAIN;
1598
1599         blk_queue_ordered(sdkp->disk->queue, ordered, sd_prepare_flush);
1600
1601         set_capacity(disk, sdkp->capacity);
1602         kfree(buffer);
1603
1604  out:
1605         return 0;
1606 }
1607
1608 /**
1609  *      sd_probe - called during driver initialization and whenever a
1610  *      new scsi device is attached to the system. It is called once
1611  *      for each scsi device (not just disks) present.
1612  *      @dev: pointer to device object
1613  *
1614  *      Returns 0 if successful (or not interested in this scsi device 
1615  *      (e.g. scanner)); 1 when there is an error.
1616  *
1617  *      Note: this function is invoked from the scsi mid-level.
1618  *      This function sets up the mapping between a given 
1619  *      <host,channel,id,lun> (found in sdp) and new device name 
1620  *      (e.g. /dev/sda). More precisely it is the block device major 
1621  *      and minor number that is chosen here.
1622  *
1623  *      Assume sd_attach is not re-entrant (for time being)
1624  *      Also think about sd_attach() and sd_remove() running coincidentally.
1625  **/
1626 static int sd_probe(struct device *dev)
1627 {
1628         struct scsi_device *sdp = to_scsi_device(dev);
1629         struct scsi_disk *sdkp;
1630         struct gendisk *gd;
1631         u32 index;
1632         int error;
1633
1634         error = -ENODEV;
1635         if (sdp->type != TYPE_DISK && sdp->type != TYPE_MOD && sdp->type != TYPE_RBC)
1636                 goto out;
1637
1638         SCSI_LOG_HLQUEUE(3, sdev_printk(KERN_INFO, sdp,
1639                                         "sd_attach\n"));
1640
1641         error = -ENOMEM;
1642         sdkp = kzalloc(sizeof(*sdkp), GFP_KERNEL);
1643         if (!sdkp)
1644                 goto out;
1645
1646         gd = alloc_disk(16);
1647         if (!gd)
1648                 goto out_free;
1649
1650         if (!idr_pre_get(&sd_index_idr, GFP_KERNEL))
1651                 goto out_put;
1652
1653         spin_lock(&sd_index_lock);
1654         error = idr_get_new(&sd_index_idr, NULL, &index);
1655         spin_unlock(&sd_index_lock);
1656
1657         if (index >= SD_MAX_DISKS)
1658                 error = -EBUSY;
1659         if (error)
1660                 goto out_put;
1661
1662         sdkp->device = sdp;
1663         sdkp->driver = &sd_template;
1664         sdkp->disk = gd;
1665         sdkp->index = index;
1666         sdkp->openers = 0;
1667         sdkp->previous_state = 1;
1668
1669         if (!sdp->timeout) {
1670                 if (sdp->type != TYPE_MOD)
1671                         sdp->timeout = SD_TIMEOUT;
1672                 else
1673                         sdp->timeout = SD_MOD_TIMEOUT;
1674         }
1675
1676         device_initialize(&sdkp->dev);
1677         sdkp->dev.parent = &sdp->sdev_gendev;
1678         sdkp->dev.class = &sd_disk_class;
1679         strncpy(sdkp->dev.bus_id, sdp->sdev_gendev.bus_id, BUS_ID_SIZE);
1680
1681         if (device_add(&sdkp->dev))
1682                 goto out_put;
1683
1684         get_device(&sdp->sdev_gendev);
1685
1686         gd->major = sd_major((index & 0xf0) >> 4);
1687         gd->first_minor = ((index & 0xf) << 4) | (index & 0xfff00);
1688         gd->minors = 16;
1689         gd->fops = &sd_fops;
1690
1691         if (index < 26) {
1692                 sprintf(gd->disk_name, "sd%c", 'a' + index % 26);
1693         } else if (index < (26 + 1) * 26) {
1694                 sprintf(gd->disk_name, "sd%c%c",
1695                         'a' + index / 26 - 1,'a' + index % 26);
1696         } else {
1697                 const unsigned int m1 = (index / 26 - 1) / 26 - 1;
1698                 const unsigned int m2 = (index / 26 - 1) % 26;
1699                 const unsigned int m3 =  index % 26;
1700                 sprintf(gd->disk_name, "sd%c%c%c",
1701                         'a' + m1, 'a' + m2, 'a' + m3);
1702         }
1703
1704         gd->private_data = &sdkp->driver;
1705         gd->queue = sdkp->device->request_queue;
1706
1707         sd_revalidate_disk(gd);
1708
1709         blk_queue_prep_rq(sdp->request_queue, sd_prep_fn);
1710
1711         gd->driverfs_dev = &sdp->sdev_gendev;
1712         gd->flags = GENHD_FL_DRIVERFS;
1713         if (sdp->removable)
1714                 gd->flags |= GENHD_FL_REMOVABLE;
1715
1716         dev_set_drvdata(dev, sdkp);
1717         add_disk(gd);
1718
1719         sd_printk(KERN_NOTICE, sdkp, "Attached SCSI %sdisk\n",
1720                   sdp->removable ? "removable " : "");
1721
1722         return 0;
1723
1724  out_put:
1725         put_disk(gd);
1726  out_free:
1727         kfree(sdkp);
1728  out:
1729         return error;
1730 }
1731
1732 /**
1733  *      sd_remove - called whenever a scsi disk (previously recognized by
1734  *      sd_probe) is detached from the system. It is called (potentially
1735  *      multiple times) during sd module unload.
1736  *      @sdp: pointer to mid level scsi device object
1737  *
1738  *      Note: this function is invoked from the scsi mid-level.
1739  *      This function potentially frees up a device name (e.g. /dev/sdc)
1740  *      that could be re-used by a subsequent sd_probe().
1741  *      This function is not called when the built-in sd driver is "exit-ed".
1742  **/
1743 static int sd_remove(struct device *dev)
1744 {
1745         struct scsi_disk *sdkp = dev_get_drvdata(dev);
1746
1747         device_del(&sdkp->dev);
1748         del_gendisk(sdkp->disk);
1749         sd_shutdown(dev);
1750
1751         mutex_lock(&sd_ref_mutex);
1752         dev_set_drvdata(dev, NULL);
1753         put_device(&sdkp->dev);
1754         mutex_unlock(&sd_ref_mutex);
1755
1756         return 0;
1757 }
1758
1759 /**
1760  *      scsi_disk_release - Called to free the scsi_disk structure
1761  *      @dev: pointer to embedded class device
1762  *
1763  *      sd_ref_mutex must be held entering this routine.  Because it is
1764  *      called on last put, you should always use the scsi_disk_get()
1765  *      scsi_disk_put() helpers which manipulate the semaphore directly
1766  *      and never do a direct put_device.
1767  **/
1768 static void scsi_disk_release(struct device *dev)
1769 {
1770         struct scsi_disk *sdkp = to_scsi_disk(dev);
1771         struct gendisk *disk = sdkp->disk;
1772         
1773         spin_lock(&sd_index_lock);
1774         idr_remove(&sd_index_idr, sdkp->index);
1775         spin_unlock(&sd_index_lock);
1776
1777         disk->private_data = NULL;
1778         put_disk(disk);
1779         put_device(&sdkp->device->sdev_gendev);
1780
1781         kfree(sdkp);
1782 }
1783
1784 static int sd_start_stop_device(struct scsi_disk *sdkp, int start)
1785 {
1786         unsigned char cmd[6] = { START_STOP };  /* START_VALID */
1787         struct scsi_sense_hdr sshdr;
1788         struct scsi_device *sdp = sdkp->device;
1789         int res;
1790
1791         if (start)
1792                 cmd[4] |= 1;    /* START */
1793
1794         if (!scsi_device_online(sdp))
1795                 return -ENODEV;
1796
1797         res = scsi_execute_req(sdp, cmd, DMA_NONE, NULL, 0, &sshdr,
1798                                SD_TIMEOUT, SD_MAX_RETRIES);
1799         if (res) {
1800                 sd_printk(KERN_WARNING, sdkp, "START_STOP FAILED\n");
1801                 sd_print_result(sdkp, res);
1802                 if (driver_byte(res) & DRIVER_SENSE)
1803                         sd_print_sense_hdr(sdkp, &sshdr);
1804         }
1805
1806         return res;
1807 }
1808
1809 /*
1810  * Send a SYNCHRONIZE CACHE instruction down to the device through
1811  * the normal SCSI command structure.  Wait for the command to
1812  * complete.
1813  */
1814 static void sd_shutdown(struct device *dev)
1815 {
1816         struct scsi_disk *sdkp = scsi_disk_get_from_dev(dev);
1817
1818         if (!sdkp)
1819                 return;         /* this can happen */
1820
1821         if (sdkp->WCE) {
1822                 sd_printk(KERN_NOTICE, sdkp, "Synchronizing SCSI cache\n");
1823                 sd_sync_cache(sdkp);
1824         }
1825
1826         if (system_state != SYSTEM_RESTART && sdkp->device->manage_start_stop) {
1827                 sd_printk(KERN_NOTICE, sdkp, "Stopping disk\n");
1828                 sd_start_stop_device(sdkp, 0);
1829         }
1830
1831         scsi_disk_put(sdkp);
1832 }
1833
1834 static int sd_suspend(struct device *dev, pm_message_t mesg)
1835 {
1836         struct scsi_disk *sdkp = scsi_disk_get_from_dev(dev);
1837         int ret = 0;
1838
1839         if (!sdkp)
1840                 return 0;       /* this can happen */
1841
1842         if (sdkp->WCE) {
1843                 sd_printk(KERN_NOTICE, sdkp, "Synchronizing SCSI cache\n");
1844                 ret = sd_sync_cache(sdkp);
1845                 if (ret)
1846                         goto done;
1847         }
1848
1849         if ((mesg.event & PM_EVENT_SLEEP) && sdkp->device->manage_start_stop) {
1850                 sd_printk(KERN_NOTICE, sdkp, "Stopping disk\n");
1851                 ret = sd_start_stop_device(sdkp, 0);
1852         }
1853
1854 done:
1855         scsi_disk_put(sdkp);
1856         return ret;
1857 }
1858
1859 static int sd_resume(struct device *dev)
1860 {
1861         struct scsi_disk *sdkp = scsi_disk_get_from_dev(dev);
1862         int ret = 0;
1863
1864         if (!sdkp->device->manage_start_stop)
1865                 goto done;
1866
1867         sd_printk(KERN_NOTICE, sdkp, "Starting disk\n");
1868         ret = sd_start_stop_device(sdkp, 1);
1869
1870 done:
1871         scsi_disk_put(sdkp);
1872         return ret;
1873 }
1874
1875 /**
1876  *      init_sd - entry point for this driver (both when built in or when
1877  *      a module).
1878  *
1879  *      Note: this function registers this driver with the scsi mid-level.
1880  **/
1881 static int __init init_sd(void)
1882 {
1883         int majors = 0, i, err;
1884
1885         SCSI_LOG_HLQUEUE(3, printk("init_sd: sd driver entry point\n"));
1886
1887         for (i = 0; i < SD_MAJORS; i++)
1888                 if (register_blkdev(sd_major(i), "sd") == 0)
1889                         majors++;
1890
1891         if (!majors)
1892                 return -ENODEV;
1893
1894         err = class_register(&sd_disk_class);
1895         if (err)
1896                 goto err_out;
1897
1898         err = scsi_register_driver(&sd_template.gendrv);
1899         if (err)
1900                 goto err_out_class;
1901
1902         return 0;
1903
1904 err_out_class:
1905         class_unregister(&sd_disk_class);
1906 err_out:
1907         for (i = 0; i < SD_MAJORS; i++)
1908                 unregister_blkdev(sd_major(i), "sd");
1909         return err;
1910 }
1911
1912 /**
1913  *      exit_sd - exit point for this driver (when it is a module).
1914  *
1915  *      Note: this function unregisters this driver from the scsi mid-level.
1916  **/
1917 static void __exit exit_sd(void)
1918 {
1919         int i;
1920
1921         SCSI_LOG_HLQUEUE(3, printk("exit_sd: exiting sd driver\n"));
1922
1923         scsi_unregister_driver(&sd_template.gendrv);
1924         class_unregister(&sd_disk_class);
1925
1926         for (i = 0; i < SD_MAJORS; i++)
1927                 unregister_blkdev(sd_major(i), "sd");
1928 }
1929
1930 module_init(init_sd);
1931 module_exit(exit_sd);
1932
1933 static void sd_print_sense_hdr(struct scsi_disk *sdkp,
1934                                struct scsi_sense_hdr *sshdr)
1935 {
1936         sd_printk(KERN_INFO, sdkp, "");
1937         scsi_show_sense_hdr(sshdr);
1938         sd_printk(KERN_INFO, sdkp, "");
1939         scsi_show_extd_sense(sshdr->asc, sshdr->ascq);
1940 }
1941
1942 static void sd_print_result(struct scsi_disk *sdkp, int result)
1943 {
1944         sd_printk(KERN_INFO, sdkp, "");
1945         scsi_show_result(result);
1946 }
1947