2 * QLogic iSCSI HBA Driver
3 * Copyright (c) 2003-2010 QLogic Corporation
5 * See LICENSE.qla4xxx for copyright and licensing details.
11 #include "ql4_inline.h"
15 * qla4xxx_mailbox_command - issues mailbox commands
16 * @ha: Pointer to host adapter structure.
17 * @inCount: number of mailbox registers to load.
18 * @outCount: number of mailbox registers to return.
19 * @mbx_cmd: data pointer for mailbox in registers.
20 * @mbx_sts: data pointer for mailbox out registers.
22 * This routine isssue mailbox commands and waits for completion.
23 * If outCount is 0, this routine completes successfully WITHOUT waiting
24 * for the mailbox command to complete.
26 int qla4xxx_mailbox_command(struct scsi_qla_host *ha, uint8_t inCount,
27 uint8_t outCount, uint32_t *mbx_cmd,
30 int status = QLA_ERROR;
34 unsigned long flags = 0;
36 /* Make sure that pointers are valid */
37 if (!mbx_cmd || !mbx_sts) {
38 DEBUG2(printk("scsi%ld: %s: Invalid mbx_cmd or mbx_sts "
39 "pointer\n", ha->host_no, __func__));
44 test_bit(AF_FW_RECOVERY, &ha->flags)) {
45 DEBUG2(ql4_printk(KERN_WARNING, ha, "scsi%ld: %s: prematurely "
46 "completing mbx cmd as firmware recovery detected\n",
47 ha->host_no, __func__));
51 if ((is_aer_supported(ha)) &&
52 (test_bit(AF_PCI_CHANNEL_IO_PERM_FAILURE, &ha->flags))) {
53 DEBUG2(printk(KERN_WARNING "scsi%ld: %s: Perm failure on EEH, "
54 "timeout MBX Exiting.\n", ha->host_no, __func__));
58 /* Mailbox code active */
59 wait_count = MBOX_TOV * 100;
61 while (wait_count--) {
62 mutex_lock(&ha->mbox_sem);
63 if (!test_bit(AF_MBOX_COMMAND, &ha->flags)) {
64 set_bit(AF_MBOX_COMMAND, &ha->flags);
65 mutex_unlock(&ha->mbox_sem);
68 mutex_unlock(&ha->mbox_sem);
70 DEBUG2(printk("scsi%ld: %s: mbox_sem failed\n",
71 ha->host_no, __func__));
77 /* To prevent overwriting mailbox registers for a command that has
78 * not yet been serviced, check to see if an active command
79 * (AEN, IOCB, etc.) is interrupting, then service it.
80 * -----------------------------------------------------------------
82 spin_lock_irqsave(&ha->hardware_lock, flags);
84 if (!is_qla8022(ha)) {
85 intr_status = readl(&ha->reg->ctrl_status);
86 if (intr_status & CSR_SCSI_PROCESSOR_INTR) {
87 /* Service existing interrupt */
88 ha->isp_ops->interrupt_service_routine(ha, intr_status);
89 clear_bit(AF_MBOX_COMMAND_DONE, &ha->flags);
93 ha->mbox_status_count = outCount;
94 for (i = 0; i < outCount; i++)
95 ha->mbox_status[i] = 0;
98 /* Load all mailbox registers, except mailbox 0. */
100 printk("scsi%ld: %s: Cmd ", ha->host_no, __func__);
101 for (i = 0; i < inCount; i++)
102 printk("mb%d=%04x ", i, mbx_cmd[i]);
105 for (i = 1; i < inCount; i++)
106 writel(mbx_cmd[i], &ha->qla4_8xxx_reg->mailbox_in[i]);
107 writel(mbx_cmd[0], &ha->qla4_8xxx_reg->mailbox_in[0]);
108 readl(&ha->qla4_8xxx_reg->mailbox_in[0]);
109 writel(HINT_MBX_INT_PENDING, &ha->qla4_8xxx_reg->hint);
111 /* Load all mailbox registers, except mailbox 0. */
112 for (i = 1; i < inCount; i++)
113 writel(mbx_cmd[i], &ha->reg->mailbox[i]);
115 /* Wakeup firmware */
116 writel(mbx_cmd[0], &ha->reg->mailbox[0]);
117 readl(&ha->reg->mailbox[0]);
118 writel(set_rmask(CSR_INTR_RISC), &ha->reg->ctrl_status);
119 readl(&ha->reg->ctrl_status);
122 spin_unlock_irqrestore(&ha->hardware_lock, flags);
124 /* Wait for completion */
127 * If we don't want status, don't wait for the mailbox command to
128 * complete. For example, MBOX_CMD_RESET_FW doesn't return status,
129 * you must poll the inbound Interrupt Mask for completion.
132 status = QLA_SUCCESS;
137 * Wait for completion: Poll or completion queue
139 if (test_bit(AF_IRQ_ATTACHED, &ha->flags) &&
140 test_bit(AF_INTERRUPTS_ON, &ha->flags) &&
141 test_bit(AF_ONLINE, &ha->flags) &&
142 !test_bit(AF_HBA_GOING_AWAY, &ha->flags)) {
143 /* Do not poll for completion. Use completion queue */
144 set_bit(AF_MBOX_COMMAND_NOPOLL, &ha->flags);
145 wait_for_completion_timeout(&ha->mbx_intr_comp, MBOX_TOV * HZ);
146 clear_bit(AF_MBOX_COMMAND_NOPOLL, &ha->flags);
148 /* Poll for command to complete */
149 wait_count = jiffies + MBOX_TOV * HZ;
150 while (test_bit(AF_MBOX_COMMAND_DONE, &ha->flags) == 0) {
151 if (time_after_eq(jiffies, wait_count))
155 * Service the interrupt.
156 * The ISR will save the mailbox status registers
157 * to a temporary storage location in the adapter
161 spin_lock_irqsave(&ha->hardware_lock, flags);
162 if (is_qla8022(ha)) {
164 readl(&ha->qla4_8xxx_reg->host_int);
165 if (intr_status & ISRX_82XX_RISC_INT) {
166 ha->mbox_status_count = outCount;
168 readl(&ha->qla4_8xxx_reg->host_status);
169 ha->isp_ops->interrupt_service_routine(
171 if (test_bit(AF_INTERRUPTS_ON,
173 test_bit(AF_INTx_ENABLED,
176 ha->nx_legacy_intr.tgt_mask_reg,
180 intr_status = readl(&ha->reg->ctrl_status);
181 if (intr_status & INTR_PENDING) {
183 * Service the interrupt.
184 * The ISR will save the mailbox status
185 * registers to a temporary storage
186 * location in the adapter structure.
188 ha->mbox_status_count = outCount;
189 ha->isp_ops->interrupt_service_routine(
193 spin_unlock_irqrestore(&ha->hardware_lock, flags);
198 /* Check for mailbox timeout. */
199 if (!test_bit(AF_MBOX_COMMAND_DONE, &ha->flags)) {
200 if (is_qla8022(ha) &&
201 test_bit(AF_FW_RECOVERY, &ha->flags)) {
202 DEBUG2(ql4_printk(KERN_INFO, ha,
203 "scsi%ld: %s: prematurely completing mbx cmd as "
204 "firmware recovery detected\n",
205 ha->host_no, __func__));
208 DEBUG2(printk("scsi%ld: Mailbox Cmd 0x%08X timed out ...,"
209 " Scheduling Adapter Reset\n", ha->host_no,
211 ha->mailbox_timeout_count++;
213 set_bit(DPC_RESET_HA, &ha->dpc_flags);
218 * Copy the mailbox out registers to the caller's mailbox in/out
221 spin_lock_irqsave(&ha->hardware_lock, flags);
222 for (i = 0; i < outCount; i++)
223 mbx_sts[i] = ha->mbox_status[i];
225 /* Set return status and error flags (if applicable). */
226 switch (ha->mbox_status[0]) {
227 case MBOX_STS_COMMAND_COMPLETE:
228 status = QLA_SUCCESS;
231 case MBOX_STS_INTERMEDIATE_COMPLETION:
232 status = QLA_SUCCESS;
236 DEBUG2( printk("scsi%ld: %s: Cmd = %08X, ISP BUSY\n",
237 ha->host_no, __func__, mbx_cmd[0]));
238 ha->mailbox_timeout_count++;
242 DEBUG2(printk("scsi%ld: %s: **** FAILED, cmd = %08X, "
243 "sts = %08X ****\n", ha->host_no, __func__,
244 mbx_cmd[0], mbx_sts[0]));
247 spin_unlock_irqrestore(&ha->hardware_lock, flags);
250 mutex_lock(&ha->mbox_sem);
251 clear_bit(AF_MBOX_COMMAND, &ha->flags);
252 mutex_unlock(&ha->mbox_sem);
253 clear_bit(AF_MBOX_COMMAND_DONE, &ha->flags);
258 void qla4xxx_mailbox_premature_completion(struct scsi_qla_host *ha)
260 set_bit(AF_FW_RECOVERY, &ha->flags);
261 ql4_printk(KERN_INFO, ha, "scsi%ld: %s: set FW RECOVERY!\n",
262 ha->host_no, __func__);
264 if (test_bit(AF_MBOX_COMMAND, &ha->flags)) {
265 if (test_bit(AF_MBOX_COMMAND_NOPOLL, &ha->flags)) {
266 complete(&ha->mbx_intr_comp);
267 ql4_printk(KERN_INFO, ha, "scsi%ld: %s: Due to fw "
268 "recovery, doing premature completion of "
269 "mbx cmd\n", ha->host_no, __func__);
272 set_bit(AF_MBOX_COMMAND_DONE, &ha->flags);
273 ql4_printk(KERN_INFO, ha, "scsi%ld: %s: Due to fw "
274 "recovery, doing premature completion of "
275 "polling mbx cmd\n", ha->host_no, __func__);
281 qla4xxx_set_ifcb(struct scsi_qla_host *ha, uint32_t *mbox_cmd,
282 uint32_t *mbox_sts, dma_addr_t init_fw_cb_dma)
284 memset(mbox_cmd, 0, sizeof(mbox_cmd[0]) * MBOX_REG_COUNT);
285 memset(mbox_sts, 0, sizeof(mbox_sts[0]) * MBOX_REG_COUNT);
288 qla4_8xxx_wr_32(ha, ha->nx_db_wr_ptr, 0);
290 mbox_cmd[0] = MBOX_CMD_INITIALIZE_FIRMWARE;
292 mbox_cmd[2] = LSDW(init_fw_cb_dma);
293 mbox_cmd[3] = MSDW(init_fw_cb_dma);
294 mbox_cmd[4] = sizeof(struct addr_ctrl_blk);
295 mbox_cmd[5] = (IFCB_VER_MAX << 8) | IFCB_VER_MIN;
297 if (qla4xxx_mailbox_command(ha, 6, 6, mbox_cmd, mbox_sts) !=
299 DEBUG2(printk(KERN_WARNING "scsi%ld: %s: "
300 "MBOX_CMD_INITIALIZE_FIRMWARE"
301 " failed w/ status %04X\n",
302 ha->host_no, __func__, mbox_sts[0]));
309 qla4xxx_get_ifcb(struct scsi_qla_host *ha, uint32_t *mbox_cmd,
310 uint32_t *mbox_sts, dma_addr_t init_fw_cb_dma)
312 memset(mbox_cmd, 0, sizeof(mbox_cmd[0]) * MBOX_REG_COUNT);
313 memset(mbox_sts, 0, sizeof(mbox_sts[0]) * MBOX_REG_COUNT);
314 mbox_cmd[0] = MBOX_CMD_GET_INIT_FW_CTRL_BLOCK;
315 mbox_cmd[2] = LSDW(init_fw_cb_dma);
316 mbox_cmd[3] = MSDW(init_fw_cb_dma);
317 mbox_cmd[4] = sizeof(struct addr_ctrl_blk);
319 if (qla4xxx_mailbox_command(ha, 5, 5, mbox_cmd, mbox_sts) !=
321 DEBUG2(printk(KERN_WARNING "scsi%ld: %s: "
322 "MBOX_CMD_GET_INIT_FW_CTRL_BLOCK"
323 " failed w/ status %04X\n",
324 ha->host_no, __func__, mbox_sts[0]));
331 qla4xxx_update_local_ip(struct scsi_qla_host *ha,
332 struct addr_ctrl_blk *init_fw_cb)
334 /* Save IPv4 Address Info */
335 memcpy(ha->ip_address, init_fw_cb->ipv4_addr,
336 min(sizeof(ha->ip_address), sizeof(init_fw_cb->ipv4_addr)));
337 memcpy(ha->subnet_mask, init_fw_cb->ipv4_subnet,
338 min(sizeof(ha->subnet_mask), sizeof(init_fw_cb->ipv4_subnet)));
339 memcpy(ha->gateway, init_fw_cb->ipv4_gw_addr,
340 min(sizeof(ha->gateway), sizeof(init_fw_cb->ipv4_gw_addr)));
342 if (is_ipv6_enabled(ha)) {
343 /* Save IPv6 Address */
344 ha->ipv6_link_local_state = init_fw_cb->ipv6_lnk_lcl_addr_state;
345 ha->ipv6_addr0_state = init_fw_cb->ipv6_addr0_state;
346 ha->ipv6_addr1_state = init_fw_cb->ipv6_addr1_state;
347 ha->ipv6_default_router_state = init_fw_cb->ipv6_dflt_rtr_state;
348 ha->ipv6_link_local_addr.in6_u.u6_addr8[0] = 0xFE;
349 ha->ipv6_link_local_addr.in6_u.u6_addr8[1] = 0x80;
351 memcpy(&ha->ipv6_link_local_addr.in6_u.u6_addr8[8],
352 init_fw_cb->ipv6_if_id,
353 min(sizeof(ha->ipv6_link_local_addr)/2,
354 sizeof(init_fw_cb->ipv6_if_id)));
355 memcpy(&ha->ipv6_addr0, init_fw_cb->ipv6_addr0,
356 min(sizeof(ha->ipv6_addr0),
357 sizeof(init_fw_cb->ipv6_addr0)));
358 memcpy(&ha->ipv6_addr1, init_fw_cb->ipv6_addr1,
359 min(sizeof(ha->ipv6_addr1),
360 sizeof(init_fw_cb->ipv6_addr1)));
361 memcpy(&ha->ipv6_default_router_addr,
362 init_fw_cb->ipv6_dflt_rtr_addr,
363 min(sizeof(ha->ipv6_default_router_addr),
364 sizeof(init_fw_cb->ipv6_dflt_rtr_addr)));
369 qla4xxx_update_local_ifcb(struct scsi_qla_host *ha,
372 struct addr_ctrl_blk *init_fw_cb,
373 dma_addr_t init_fw_cb_dma)
375 if (qla4xxx_get_ifcb(ha, mbox_cmd, mbox_sts, init_fw_cb_dma)
377 DEBUG2(printk(KERN_WARNING
378 "scsi%ld: %s: Failed to get init_fw_ctrl_blk\n",
379 ha->host_no, __func__));
383 DEBUG2(qla4xxx_dump_buffer(init_fw_cb, sizeof(struct addr_ctrl_blk)));
385 /* Save some info in adapter structure. */
386 ha->acb_version = init_fw_cb->acb_version;
387 ha->firmware_options = le16_to_cpu(init_fw_cb->fw_options);
388 ha->tcp_options = le16_to_cpu(init_fw_cb->ipv4_tcp_opts);
389 ha->ipv4_options = le16_to_cpu(init_fw_cb->ipv4_ip_opts);
390 ha->ipv4_addr_state = le16_to_cpu(init_fw_cb->ipv4_addr_state);
391 ha->heartbeat_interval = init_fw_cb->hb_interval;
392 memcpy(ha->name_string, init_fw_cb->iscsi_name,
393 min(sizeof(ha->name_string),
394 sizeof(init_fw_cb->iscsi_name)));
395 /*memcpy(ha->alias, init_fw_cb->Alias,
396 min(sizeof(ha->alias), sizeof(init_fw_cb->Alias)));*/
398 /* Save Command Line Paramater info */
399 ha->discovery_wait = ql4xdiscoverywait;
401 if (ha->acb_version == ACB_SUPPORTED) {
402 ha->ipv6_options = init_fw_cb->ipv6_opts;
403 ha->ipv6_addl_options = init_fw_cb->ipv6_addtl_opts;
405 qla4xxx_update_local_ip(ha, init_fw_cb);
411 * qla4xxx_initialize_fw_cb - initializes firmware control block.
412 * @ha: Pointer to host adapter structure.
414 int qla4xxx_initialize_fw_cb(struct scsi_qla_host * ha)
416 struct addr_ctrl_blk *init_fw_cb;
417 dma_addr_t init_fw_cb_dma;
418 uint32_t mbox_cmd[MBOX_REG_COUNT];
419 uint32_t mbox_sts[MBOX_REG_COUNT];
420 int status = QLA_ERROR;
422 init_fw_cb = dma_alloc_coherent(&ha->pdev->dev,
423 sizeof(struct addr_ctrl_blk),
424 &init_fw_cb_dma, GFP_KERNEL);
425 if (init_fw_cb == NULL) {
426 DEBUG2(printk("scsi%ld: %s: Unable to alloc init_cb\n",
427 ha->host_no, __func__));
428 goto exit_init_fw_cb_no_free;
430 memset(init_fw_cb, 0, sizeof(struct addr_ctrl_blk));
432 /* Get Initialize Firmware Control Block. */
433 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
434 memset(&mbox_sts, 0, sizeof(mbox_sts));
436 if (qla4xxx_get_ifcb(ha, &mbox_cmd[0], &mbox_sts[0], init_fw_cb_dma) !=
438 dma_free_coherent(&ha->pdev->dev,
439 sizeof(struct addr_ctrl_blk),
440 init_fw_cb, init_fw_cb_dma);
441 goto exit_init_fw_cb;
444 /* Initialize request and response queues. */
445 qla4xxx_init_rings(ha);
447 /* Fill in the request and response queue information. */
448 init_fw_cb->rqq_consumer_idx = cpu_to_le16(ha->request_out);
449 init_fw_cb->compq_producer_idx = cpu_to_le16(ha->response_in);
450 init_fw_cb->rqq_len = __constant_cpu_to_le16(REQUEST_QUEUE_DEPTH);
451 init_fw_cb->compq_len = __constant_cpu_to_le16(RESPONSE_QUEUE_DEPTH);
452 init_fw_cb->rqq_addr_lo = cpu_to_le32(LSDW(ha->request_dma));
453 init_fw_cb->rqq_addr_hi = cpu_to_le32(MSDW(ha->request_dma));
454 init_fw_cb->compq_addr_lo = cpu_to_le32(LSDW(ha->response_dma));
455 init_fw_cb->compq_addr_hi = cpu_to_le32(MSDW(ha->response_dma));
456 init_fw_cb->shdwreg_addr_lo = cpu_to_le32(LSDW(ha->shadow_regs_dma));
457 init_fw_cb->shdwreg_addr_hi = cpu_to_le32(MSDW(ha->shadow_regs_dma));
459 /* Set up required options. */
460 init_fw_cb->fw_options |=
461 __constant_cpu_to_le16(FWOPT_SESSION_MODE |
462 FWOPT_INITIATOR_MODE);
465 init_fw_cb->fw_options |=
466 __constant_cpu_to_le16(FWOPT_ENABLE_CRBDB);
468 init_fw_cb->fw_options &= __constant_cpu_to_le16(~FWOPT_TARGET_MODE);
470 if (qla4xxx_set_ifcb(ha, &mbox_cmd[0], &mbox_sts[0], init_fw_cb_dma)
472 DEBUG2(printk(KERN_WARNING
473 "scsi%ld: %s: Failed to set init_fw_ctrl_blk\n",
474 ha->host_no, __func__));
475 goto exit_init_fw_cb;
478 if (qla4xxx_update_local_ifcb(ha, &mbox_cmd[0], &mbox_sts[0],
479 init_fw_cb, init_fw_cb_dma) != QLA_SUCCESS) {
480 DEBUG2(printk("scsi%ld: %s: Failed to update local ifcb\n",
481 ha->host_no, __func__));
482 goto exit_init_fw_cb;
484 status = QLA_SUCCESS;
487 dma_free_coherent(&ha->pdev->dev, sizeof(struct addr_ctrl_blk),
488 init_fw_cb, init_fw_cb_dma);
489 exit_init_fw_cb_no_free:
494 * qla4xxx_get_dhcp_ip_address - gets HBA ip address via DHCP
495 * @ha: Pointer to host adapter structure.
497 int qla4xxx_get_dhcp_ip_address(struct scsi_qla_host * ha)
499 struct addr_ctrl_blk *init_fw_cb;
500 dma_addr_t init_fw_cb_dma;
501 uint32_t mbox_cmd[MBOX_REG_COUNT];
502 uint32_t mbox_sts[MBOX_REG_COUNT];
504 init_fw_cb = dma_alloc_coherent(&ha->pdev->dev,
505 sizeof(struct addr_ctrl_blk),
506 &init_fw_cb_dma, GFP_KERNEL);
507 if (init_fw_cb == NULL) {
508 printk("scsi%ld: %s: Unable to alloc init_cb\n", ha->host_no,
513 /* Get Initialize Firmware Control Block. */
514 memset(init_fw_cb, 0, sizeof(struct addr_ctrl_blk));
515 if (qla4xxx_get_ifcb(ha, &mbox_cmd[0], &mbox_sts[0], init_fw_cb_dma) !=
517 DEBUG2(printk("scsi%ld: %s: Failed to get init_fw_ctrl_blk\n",
518 ha->host_no, __func__));
519 dma_free_coherent(&ha->pdev->dev,
520 sizeof(struct addr_ctrl_blk),
521 init_fw_cb, init_fw_cb_dma);
525 /* Save IP Address. */
526 qla4xxx_update_local_ip(ha, init_fw_cb);
527 dma_free_coherent(&ha->pdev->dev, sizeof(struct addr_ctrl_blk),
528 init_fw_cb, init_fw_cb_dma);
534 * qla4xxx_get_firmware_state - gets firmware state of HBA
535 * @ha: Pointer to host adapter structure.
537 int qla4xxx_get_firmware_state(struct scsi_qla_host * ha)
539 uint32_t mbox_cmd[MBOX_REG_COUNT];
540 uint32_t mbox_sts[MBOX_REG_COUNT];
542 /* Get firmware version */
543 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
544 memset(&mbox_sts, 0, sizeof(mbox_sts));
546 mbox_cmd[0] = MBOX_CMD_GET_FW_STATE;
548 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 4, &mbox_cmd[0], &mbox_sts[0]) !=
550 DEBUG2(printk("scsi%ld: %s: MBOX_CMD_GET_FW_STATE failed w/ "
551 "status %04X\n", ha->host_no, __func__,
555 ha->firmware_state = mbox_sts[1];
556 ha->board_id = mbox_sts[2];
557 ha->addl_fw_state = mbox_sts[3];
558 DEBUG2(printk("scsi%ld: %s firmware_state=0x%x\n",
559 ha->host_no, __func__, ha->firmware_state);)
565 * qla4xxx_get_firmware_status - retrieves firmware status
566 * @ha: Pointer to host adapter structure.
568 int qla4xxx_get_firmware_status(struct scsi_qla_host * ha)
570 uint32_t mbox_cmd[MBOX_REG_COUNT];
571 uint32_t mbox_sts[MBOX_REG_COUNT];
573 /* Get firmware version */
574 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
575 memset(&mbox_sts, 0, sizeof(mbox_sts));
577 mbox_cmd[0] = MBOX_CMD_GET_FW_STATUS;
579 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 3, &mbox_cmd[0], &mbox_sts[0]) !=
581 DEBUG2(printk("scsi%ld: %s: MBOX_CMD_GET_FW_STATUS failed w/ "
582 "status %04X\n", ha->host_no, __func__,
587 ql4_printk(KERN_INFO, ha, "%ld firmare IOCBs available (%d).\n",
588 ha->host_no, mbox_sts[2]);
594 * qla4xxx_get_fwddb_entry - retrieves firmware ddb entry
595 * @ha: Pointer to host adapter structure.
596 * @fw_ddb_index: Firmware's device database index
597 * @fw_ddb_entry: Pointer to firmware's device database entry structure
598 * @num_valid_ddb_entries: Pointer to number of valid ddb entries
599 * @next_ddb_index: Pointer to next valid device database index
600 * @fw_ddb_device_state: Pointer to device state
602 int qla4xxx_get_fwddb_entry(struct scsi_qla_host *ha,
603 uint16_t fw_ddb_index,
604 struct dev_db_entry *fw_ddb_entry,
605 dma_addr_t fw_ddb_entry_dma,
606 uint32_t *num_valid_ddb_entries,
607 uint32_t *next_ddb_index,
608 uint32_t *fw_ddb_device_state,
609 uint32_t *conn_err_detail,
610 uint16_t *tcp_source_port_num,
611 uint16_t *connection_id)
613 int status = QLA_ERROR;
615 uint32_t mbox_cmd[MBOX_REG_COUNT];
616 uint32_t mbox_sts[MBOX_REG_COUNT];
618 /* Make sure the device index is valid */
619 if (fw_ddb_index >= MAX_DDB_ENTRIES) {
620 DEBUG2(printk("scsi%ld: %s: ddb [%d] out of range.\n",
621 ha->host_no, __func__, fw_ddb_index));
624 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
625 memset(&mbox_sts, 0, sizeof(mbox_sts));
627 mbox_cmd[0] = MBOX_CMD_GET_DATABASE_ENTRY;
628 mbox_cmd[1] = (uint32_t) fw_ddb_index;
629 mbox_cmd[2] = LSDW(fw_ddb_entry_dma);
630 mbox_cmd[3] = MSDW(fw_ddb_entry_dma);
631 mbox_cmd[4] = sizeof(struct dev_db_entry);
633 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 7, &mbox_cmd[0], &mbox_sts[0]) ==
635 DEBUG2(printk("scsi%ld: %s: MBOX_CMD_GET_DATABASE_ENTRY failed"
636 " with status 0x%04X\n", ha->host_no, __func__,
640 if (fw_ddb_index != mbox_sts[1]) {
641 DEBUG2(printk("scsi%ld: %s: ddb mismatch [%d] != [%d].\n",
642 ha->host_no, __func__, fw_ddb_index,
647 options = le16_to_cpu(fw_ddb_entry->options);
648 if (options & DDB_OPT_IPV6_DEVICE) {
649 ql4_printk(KERN_INFO, ha, "%s: DDB[%d] MB0 %04x Tot %d "
650 "Next %d State %04x ConnErr %08x %pI6 "
651 ":%04d \"%s\"\n", __func__, fw_ddb_index,
652 mbox_sts[0], mbox_sts[2], mbox_sts[3],
653 mbox_sts[4], mbox_sts[5],
654 fw_ddb_entry->ip_addr,
655 le16_to_cpu(fw_ddb_entry->port),
656 fw_ddb_entry->iscsi_name);
658 ql4_printk(KERN_INFO, ha, "%s: DDB[%d] MB0 %04x Tot %d "
659 "Next %d State %04x ConnErr %08x %pI4 "
660 ":%04d \"%s\"\n", __func__, fw_ddb_index,
661 mbox_sts[0], mbox_sts[2], mbox_sts[3],
662 mbox_sts[4], mbox_sts[5],
663 fw_ddb_entry->ip_addr,
664 le16_to_cpu(fw_ddb_entry->port),
665 fw_ddb_entry->iscsi_name);
668 if (num_valid_ddb_entries)
669 *num_valid_ddb_entries = mbox_sts[2];
671 *next_ddb_index = mbox_sts[3];
672 if (fw_ddb_device_state)
673 *fw_ddb_device_state = mbox_sts[4];
676 * RA: This mailbox has been changed to pass connection error and
677 * details. Its true for ISP4010 as per Version E - Not sure when it
678 * was changed. Get the time2wait from the fw_dd_entry field :
679 * default_time2wait which we call it as minTime2Wait DEV_DB_ENTRY
683 *conn_err_detail = mbox_sts[5];
684 if (tcp_source_port_num)
685 *tcp_source_port_num = (uint16_t) (mbox_sts[6] >> 16);
687 *connection_id = (uint16_t) mbox_sts[6] & 0x00FF;
688 status = QLA_SUCCESS;
695 * qla4xxx_set_fwddb_entry - sets a ddb entry.
696 * @ha: Pointer to host adapter structure.
697 * @fw_ddb_index: Firmware's device database index
698 * @fw_ddb_entry: Pointer to firmware's ddb entry structure, or NULL.
700 * This routine initializes or updates the adapter's device database
701 * entry for the specified device. It also triggers a login for the
702 * specified device. Therefore, it may also be used as a secondary
703 * login routine when a NULL pointer is specified for the fw_ddb_entry.
705 int qla4xxx_set_ddb_entry(struct scsi_qla_host * ha, uint16_t fw_ddb_index,
706 dma_addr_t fw_ddb_entry_dma)
708 uint32_t mbox_cmd[MBOX_REG_COUNT];
709 uint32_t mbox_sts[MBOX_REG_COUNT];
712 /* Do not wait for completion. The firmware will send us an
713 * ASTS_DATABASE_CHANGED (0x8014) to notify us of the login status.
715 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
716 memset(&mbox_sts, 0, sizeof(mbox_sts));
718 mbox_cmd[0] = MBOX_CMD_SET_DATABASE_ENTRY;
719 mbox_cmd[1] = (uint32_t) fw_ddb_index;
720 mbox_cmd[2] = LSDW(fw_ddb_entry_dma);
721 mbox_cmd[3] = MSDW(fw_ddb_entry_dma);
722 mbox_cmd[4] = sizeof(struct dev_db_entry);
724 status = qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 5, &mbox_cmd[0],
726 DEBUG2(printk("scsi%ld: %s: status=%d mbx0=0x%x mbx4=0x%x\n",
727 ha->host_no, __func__, status, mbox_sts[0], mbox_sts[4]);)
733 * qla4xxx_get_crash_record - retrieves crash record.
734 * @ha: Pointer to host adapter structure.
736 * This routine retrieves a crash record from the QLA4010 after an 8002h aen.
738 void qla4xxx_get_crash_record(struct scsi_qla_host * ha)
740 uint32_t mbox_cmd[MBOX_REG_COUNT];
741 uint32_t mbox_sts[MBOX_REG_COUNT];
742 struct crash_record *crash_record = NULL;
743 dma_addr_t crash_record_dma = 0;
744 uint32_t crash_record_size = 0;
746 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
747 memset(&mbox_sts, 0, sizeof(mbox_cmd));
749 /* Get size of crash record. */
750 mbox_cmd[0] = MBOX_CMD_GET_CRASH_RECORD;
752 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 5, &mbox_cmd[0], &mbox_sts[0]) !=
754 DEBUG2(printk("scsi%ld: %s: ERROR: Unable to retrieve size!\n",
755 ha->host_no, __func__));
756 goto exit_get_crash_record;
758 crash_record_size = mbox_sts[4];
759 if (crash_record_size == 0) {
760 DEBUG2(printk("scsi%ld: %s: ERROR: Crash record size is 0!\n",
761 ha->host_no, __func__));
762 goto exit_get_crash_record;
765 /* Alloc Memory for Crash Record. */
766 crash_record = dma_alloc_coherent(&ha->pdev->dev, crash_record_size,
767 &crash_record_dma, GFP_KERNEL);
768 if (crash_record == NULL)
769 goto exit_get_crash_record;
771 /* Get Crash Record. */
772 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
773 memset(&mbox_sts, 0, sizeof(mbox_cmd));
775 mbox_cmd[0] = MBOX_CMD_GET_CRASH_RECORD;
776 mbox_cmd[2] = LSDW(crash_record_dma);
777 mbox_cmd[3] = MSDW(crash_record_dma);
778 mbox_cmd[4] = crash_record_size;
780 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 5, &mbox_cmd[0], &mbox_sts[0]) !=
782 goto exit_get_crash_record;
784 /* Dump Crash Record. */
786 exit_get_crash_record:
788 dma_free_coherent(&ha->pdev->dev, crash_record_size,
789 crash_record, crash_record_dma);
793 * qla4xxx_get_conn_event_log - retrieves connection event log
794 * @ha: Pointer to host adapter structure.
796 void qla4xxx_get_conn_event_log(struct scsi_qla_host * ha)
798 uint32_t mbox_cmd[MBOX_REG_COUNT];
799 uint32_t mbox_sts[MBOX_REG_COUNT];
800 struct conn_event_log_entry *event_log = NULL;
801 dma_addr_t event_log_dma = 0;
802 uint32_t event_log_size = 0;
803 uint32_t num_valid_entries;
804 uint32_t oldest_entry = 0;
805 uint32_t max_event_log_entries;
809 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
810 memset(&mbox_sts, 0, sizeof(mbox_cmd));
812 /* Get size of crash record. */
813 mbox_cmd[0] = MBOX_CMD_GET_CONN_EVENT_LOG;
815 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 5, &mbox_cmd[0], &mbox_sts[0]) !=
817 goto exit_get_event_log;
819 event_log_size = mbox_sts[4];
820 if (event_log_size == 0)
821 goto exit_get_event_log;
823 /* Alloc Memory for Crash Record. */
824 event_log = dma_alloc_coherent(&ha->pdev->dev, event_log_size,
825 &event_log_dma, GFP_KERNEL);
826 if (event_log == NULL)
827 goto exit_get_event_log;
829 /* Get Crash Record. */
830 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
831 memset(&mbox_sts, 0, sizeof(mbox_cmd));
833 mbox_cmd[0] = MBOX_CMD_GET_CONN_EVENT_LOG;
834 mbox_cmd[2] = LSDW(event_log_dma);
835 mbox_cmd[3] = MSDW(event_log_dma);
837 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 5, &mbox_cmd[0], &mbox_sts[0]) !=
839 DEBUG2(printk("scsi%ld: %s: ERROR: Unable to retrieve event "
840 "log!\n", ha->host_no, __func__));
841 goto exit_get_event_log;
844 /* Dump Event Log. */
845 num_valid_entries = mbox_sts[1];
847 max_event_log_entries = event_log_size /
848 sizeof(struct conn_event_log_entry);
850 if (num_valid_entries > max_event_log_entries)
851 oldest_entry = num_valid_entries % max_event_log_entries;
853 DEBUG3(printk("scsi%ld: Connection Event Log Dump (%d entries):\n",
854 ha->host_no, num_valid_entries));
856 if (ql4xextended_error_logging == 3) {
857 if (oldest_entry == 0) {
858 /* Circular Buffer has not wrapped around */
859 for (i=0; i < num_valid_entries; i++) {
860 qla4xxx_dump_buffer((uint8_t *)event_log+
861 (i*sizeof(*event_log)),
866 /* Circular Buffer has wrapped around -
867 * display accordingly*/
868 for (i=oldest_entry; i < max_event_log_entries; i++) {
869 qla4xxx_dump_buffer((uint8_t *)event_log+
870 (i*sizeof(*event_log)),
873 for (i=0; i < oldest_entry; i++) {
874 qla4xxx_dump_buffer((uint8_t *)event_log+
875 (i*sizeof(*event_log)),
883 dma_free_coherent(&ha->pdev->dev, event_log_size, event_log,
888 * qla4xxx_abort_task - issues Abort Task
889 * @ha: Pointer to host adapter structure.
890 * @srb: Pointer to srb entry
892 * This routine performs a LUN RESET on the specified target/lun.
893 * The caller must ensure that the ddb_entry and lun_entry pointers
894 * are valid before calling this routine.
896 int qla4xxx_abort_task(struct scsi_qla_host *ha, struct srb *srb)
898 uint32_t mbox_cmd[MBOX_REG_COUNT];
899 uint32_t mbox_sts[MBOX_REG_COUNT];
900 struct scsi_cmnd *cmd = srb->cmd;
901 int status = QLA_SUCCESS;
902 unsigned long flags = 0;
906 * Send abort task command to ISP, so that the ISP will return
907 * request with ABORT status
909 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
910 memset(&mbox_sts, 0, sizeof(mbox_sts));
912 spin_lock_irqsave(&ha->hardware_lock, flags);
913 index = (unsigned long)(unsigned char *)cmd->host_scribble;
914 spin_unlock_irqrestore(&ha->hardware_lock, flags);
916 /* Firmware already posted completion on response queue */
917 if (index == MAX_SRBS)
920 mbox_cmd[0] = MBOX_CMD_ABORT_TASK;
921 mbox_cmd[1] = srb->ddb->fw_ddb_index;
923 /* Immediate Command Enable */
926 qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 5, &mbox_cmd[0],
928 if (mbox_sts[0] != MBOX_STS_COMMAND_COMPLETE) {
931 DEBUG2(printk(KERN_WARNING "scsi%ld:%d:%d: abort task FAILED: "
932 "mbx0=%04X, mb1=%04X, mb2=%04X, mb3=%04X, mb4=%04X\n",
933 ha->host_no, cmd->device->id, cmd->device->lun, mbox_sts[0],
934 mbox_sts[1], mbox_sts[2], mbox_sts[3], mbox_sts[4]));
941 * qla4xxx_reset_lun - issues LUN Reset
942 * @ha: Pointer to host adapter structure.
943 * @ddb_entry: Pointer to device database entry
946 * This routine performs a LUN RESET on the specified target/lun.
947 * The caller must ensure that the ddb_entry and lun_entry pointers
948 * are valid before calling this routine.
950 int qla4xxx_reset_lun(struct scsi_qla_host * ha, struct ddb_entry * ddb_entry,
953 uint32_t mbox_cmd[MBOX_REG_COUNT];
954 uint32_t mbox_sts[MBOX_REG_COUNT];
955 int status = QLA_SUCCESS;
957 DEBUG2(printk("scsi%ld:%d:%d: lun reset issued\n", ha->host_no,
958 ddb_entry->fw_ddb_index, lun));
961 * Send lun reset command to ISP, so that the ISP will return all
962 * outstanding requests with RESET status
964 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
965 memset(&mbox_sts, 0, sizeof(mbox_sts));
967 mbox_cmd[0] = MBOX_CMD_LUN_RESET;
968 mbox_cmd[1] = ddb_entry->fw_ddb_index;
969 mbox_cmd[2] = lun << 8;
970 mbox_cmd[5] = 0x01; /* Immediate Command Enable */
972 qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 1, &mbox_cmd[0], &mbox_sts[0]);
973 if (mbox_sts[0] != MBOX_STS_COMMAND_COMPLETE &&
974 mbox_sts[0] != MBOX_STS_COMMAND_ERROR)
981 * qla4xxx_reset_target - issues target Reset
982 * @ha: Pointer to host adapter structure.
983 * @db_entry: Pointer to device database entry
984 * @un_entry: Pointer to lun entry structure
986 * This routine performs a TARGET RESET on the specified target.
987 * The caller must ensure that the ddb_entry pointers
988 * are valid before calling this routine.
990 int qla4xxx_reset_target(struct scsi_qla_host *ha,
991 struct ddb_entry *ddb_entry)
993 uint32_t mbox_cmd[MBOX_REG_COUNT];
994 uint32_t mbox_sts[MBOX_REG_COUNT];
995 int status = QLA_SUCCESS;
997 DEBUG2(printk("scsi%ld:%d: target reset issued\n", ha->host_no,
998 ddb_entry->fw_ddb_index));
1001 * Send target reset command to ISP, so that the ISP will return all
1002 * outstanding requests with RESET status
1004 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
1005 memset(&mbox_sts, 0, sizeof(mbox_sts));
1007 mbox_cmd[0] = MBOX_CMD_TARGET_WARM_RESET;
1008 mbox_cmd[1] = ddb_entry->fw_ddb_index;
1009 mbox_cmd[5] = 0x01; /* Immediate Command Enable */
1011 qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 1, &mbox_cmd[0],
1013 if (mbox_sts[0] != MBOX_STS_COMMAND_COMPLETE &&
1014 mbox_sts[0] != MBOX_STS_COMMAND_ERROR)
1020 int qla4xxx_get_flash(struct scsi_qla_host * ha, dma_addr_t dma_addr,
1021 uint32_t offset, uint32_t len)
1023 uint32_t mbox_cmd[MBOX_REG_COUNT];
1024 uint32_t mbox_sts[MBOX_REG_COUNT];
1026 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
1027 memset(&mbox_sts, 0, sizeof(mbox_sts));
1029 mbox_cmd[0] = MBOX_CMD_READ_FLASH;
1030 mbox_cmd[1] = LSDW(dma_addr);
1031 mbox_cmd[2] = MSDW(dma_addr);
1032 mbox_cmd[3] = offset;
1035 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 2, &mbox_cmd[0], &mbox_sts[0]) !=
1037 DEBUG2(printk("scsi%ld: %s: MBOX_CMD_READ_FLASH, failed w/ "
1038 "status %04X %04X, offset %08x, len %08x\n", ha->host_no,
1039 __func__, mbox_sts[0], mbox_sts[1], offset, len));
1046 * qla4xxx_get_fw_version - gets firmware version
1047 * @ha: Pointer to host adapter structure.
1049 * Retrieves the firmware version on HBA. In QLA4010, mailboxes 2 & 3 may
1050 * hold an address for data. Make sure that we write 0 to those mailboxes,
1053 int qla4xxx_get_fw_version(struct scsi_qla_host * ha)
1055 uint32_t mbox_cmd[MBOX_REG_COUNT];
1056 uint32_t mbox_sts[MBOX_REG_COUNT];
1058 /* Get firmware version. */
1059 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
1060 memset(&mbox_sts, 0, sizeof(mbox_sts));
1062 mbox_cmd[0] = MBOX_CMD_ABOUT_FW;
1064 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 5, &mbox_cmd[0], &mbox_sts[0]) !=
1066 DEBUG2(printk("scsi%ld: %s: MBOX_CMD_ABOUT_FW failed w/ "
1067 "status %04X\n", ha->host_no, __func__, mbox_sts[0]));
1071 /* Save firmware version information. */
1072 ha->firmware_version[0] = mbox_sts[1];
1073 ha->firmware_version[1] = mbox_sts[2];
1074 ha->patch_number = mbox_sts[3];
1075 ha->build_number = mbox_sts[4];
1080 static int qla4xxx_get_default_ddb(struct scsi_qla_host *ha,
1081 dma_addr_t dma_addr)
1083 uint32_t mbox_cmd[MBOX_REG_COUNT];
1084 uint32_t mbox_sts[MBOX_REG_COUNT];
1086 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
1087 memset(&mbox_sts, 0, sizeof(mbox_sts));
1089 mbox_cmd[0] = MBOX_CMD_GET_DATABASE_ENTRY_DEFAULTS;
1090 mbox_cmd[2] = LSDW(dma_addr);
1091 mbox_cmd[3] = MSDW(dma_addr);
1093 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 1, &mbox_cmd[0], &mbox_sts[0]) !=
1095 DEBUG2(printk("scsi%ld: %s: failed status %04X\n",
1096 ha->host_no, __func__, mbox_sts[0]));
1102 static int qla4xxx_req_ddb_entry(struct scsi_qla_host *ha, uint32_t *ddb_index)
1104 uint32_t mbox_cmd[MBOX_REG_COUNT];
1105 uint32_t mbox_sts[MBOX_REG_COUNT];
1107 memset(&mbox_cmd, 0, sizeof(mbox_cmd));
1108 memset(&mbox_sts, 0, sizeof(mbox_sts));
1110 mbox_cmd[0] = MBOX_CMD_REQUEST_DATABASE_ENTRY;
1111 mbox_cmd[1] = MAX_PRST_DEV_DB_ENTRIES;
1113 if (qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 3, &mbox_cmd[0], &mbox_sts[0]) !=
1115 if (mbox_sts[0] == MBOX_STS_COMMAND_ERROR) {
1116 *ddb_index = mbox_sts[2];
1118 DEBUG2(printk("scsi%ld: %s: failed status %04X\n",
1119 ha->host_no, __func__, mbox_sts[0]));
1123 *ddb_index = MAX_PRST_DEV_DB_ENTRIES;
1130 int qla4xxx_send_tgts(struct scsi_qla_host *ha, char *ip, uint16_t port)
1132 struct dev_db_entry *fw_ddb_entry;
1133 dma_addr_t fw_ddb_entry_dma;
1135 int ret_val = QLA_SUCCESS;
1138 fw_ddb_entry = dma_alloc_coherent(&ha->pdev->dev,
1139 sizeof(*fw_ddb_entry),
1140 &fw_ddb_entry_dma, GFP_KERNEL);
1141 if (!fw_ddb_entry) {
1142 DEBUG2(printk("scsi%ld: %s: Unable to allocate dma buffer.\n",
1143 ha->host_no, __func__));
1144 ret_val = QLA_ERROR;
1145 goto exit_send_tgts_no_free;
1148 ret_val = qla4xxx_get_default_ddb(ha, fw_ddb_entry_dma);
1149 if (ret_val != QLA_SUCCESS)
1150 goto exit_send_tgts;
1152 ret_val = qla4xxx_req_ddb_entry(ha, &ddb_index);
1153 if (ret_val != QLA_SUCCESS)
1154 goto exit_send_tgts;
1156 memset(fw_ddb_entry->iscsi_alias, 0,
1157 sizeof(fw_ddb_entry->iscsi_alias));
1159 memset(fw_ddb_entry->iscsi_name, 0,
1160 sizeof(fw_ddb_entry->iscsi_name));
1162 memset(fw_ddb_entry->ip_addr, 0, sizeof(fw_ddb_entry->ip_addr));
1163 memset(fw_ddb_entry->tgt_addr, 0,
1164 sizeof(fw_ddb_entry->tgt_addr));
1166 fw_ddb_entry->options = (DDB_OPT_DISC_SESSION | DDB_OPT_TARGET);
1167 fw_ddb_entry->port = cpu_to_le16(ntohs(port));
1169 fw_ddb_entry->ip_addr[0] = *ip;
1170 fw_ddb_entry->ip_addr[1] = *(ip + 1);
1171 fw_ddb_entry->ip_addr[2] = *(ip + 2);
1172 fw_ddb_entry->ip_addr[3] = *(ip + 3);
1174 ret_val = qla4xxx_set_ddb_entry(ha, ddb_index, fw_ddb_entry_dma);
1177 dma_free_coherent(&ha->pdev->dev, sizeof(*fw_ddb_entry),
1178 fw_ddb_entry, fw_ddb_entry_dma);
1179 exit_send_tgts_no_free: