2 * This file is part of wl1271
4 * Copyright (C) 2008-2010 Nokia Corporation
6 * Contact: Luciano Coelho <luciano.coelho@nokia.com>
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License
10 * version 2 as published by the Free Software Foundation.
12 * This program is distributed in the hope that it will be useful, but
13 * WITHOUT ANY WARRANTY; without even the implied warranty of
14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
15 * General Public License for more details.
17 * You should have received a copy of the GNU General Public License
18 * along with this program; if not, write to the Free Software
19 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
24 #include <linux/slab.h>
25 #include <linux/wl12xx.h>
26 #include <linux/export.h>
35 static struct wl1271_partition_set part_table[PART_TABLE_LEN] = {
42 .start = REGISTERS_BASE,
61 .start = REGISTERS_BASE,
94 static void wl1271_boot_set_ecpu_ctrl(struct wl1271 *wl, u32 flag)
98 /* 10.5.0 run the firmware (I) */
99 cpu_ctrl = wl1271_read32(wl, ACX_REG_ECPU_CONTROL);
101 /* 10.5.1 run the firmware (II) */
103 wl1271_write32(wl, ACX_REG_ECPU_CONTROL, cpu_ctrl);
106 static unsigned int wl12xx_get_fw_ver_quirks(struct wl1271 *wl)
108 unsigned int quirks = 0;
109 unsigned int *fw_ver = wl->chip.fw_ver;
111 /* Only new station firmwares support routing fw logs to the host */
112 if ((fw_ver[FW_VER_IF_TYPE] == FW_VER_IF_TYPE_STA) &&
113 (fw_ver[FW_VER_MINOR] < FW_VER_MINOR_FWLOG_STA_MIN))
114 quirks |= WL12XX_QUIRK_FWLOG_NOT_IMPLEMENTED;
116 /* This feature is not yet supported for AP mode */
117 if (fw_ver[FW_VER_IF_TYPE] == FW_VER_IF_TYPE_AP)
118 quirks |= WL12XX_QUIRK_FWLOG_NOT_IMPLEMENTED;
123 static void wl1271_parse_fw_ver(struct wl1271 *wl)
127 ret = sscanf(wl->chip.fw_ver_str + 4, "%u.%u.%u.%u.%u",
128 &wl->chip.fw_ver[0], &wl->chip.fw_ver[1],
129 &wl->chip.fw_ver[2], &wl->chip.fw_ver[3],
130 &wl->chip.fw_ver[4]);
133 wl1271_warning("fw version incorrect value");
134 memset(wl->chip.fw_ver, 0, sizeof(wl->chip.fw_ver));
138 /* Check if any quirks are needed with older fw versions */
139 wl->quirks |= wl12xx_get_fw_ver_quirks(wl);
142 static void wl1271_boot_fw_version(struct wl1271 *wl)
144 struct wl1271_static_data static_data;
146 wl1271_read(wl, wl->cmd_box_addr, &static_data, sizeof(static_data),
149 strncpy(wl->chip.fw_ver_str, static_data.fw_version,
150 sizeof(wl->chip.fw_ver_str));
152 /* make sure the string is NULL-terminated */
153 wl->chip.fw_ver_str[sizeof(wl->chip.fw_ver_str) - 1] = '\0';
155 wl1271_parse_fw_ver(wl);
158 static int wl1271_boot_upload_firmware_chunk(struct wl1271 *wl, void *buf,
159 size_t fw_data_len, u32 dest)
161 struct wl1271_partition_set partition;
162 int addr, chunk_num, partition_limit;
165 /* whal_FwCtrl_LoadFwImageSm() */
167 wl1271_debug(DEBUG_BOOT, "starting firmware upload");
169 wl1271_debug(DEBUG_BOOT, "fw_data_len %zd chunk_size %d",
170 fw_data_len, CHUNK_SIZE);
172 if ((fw_data_len % 4) != 0) {
173 wl1271_error("firmware length not multiple of four");
177 chunk = kmalloc(CHUNK_SIZE, GFP_KERNEL);
179 wl1271_error("allocation for firmware upload chunk failed");
183 memcpy(&partition, &part_table[PART_DOWN], sizeof(partition));
184 partition.mem.start = dest;
185 wl1271_set_partition(wl, &partition);
187 /* 10.1 set partition limit and chunk num */
189 partition_limit = part_table[PART_DOWN].mem.size;
191 while (chunk_num < fw_data_len / CHUNK_SIZE) {
192 /* 10.2 update partition, if needed */
193 addr = dest + (chunk_num + 2) * CHUNK_SIZE;
194 if (addr > partition_limit) {
195 addr = dest + chunk_num * CHUNK_SIZE;
196 partition_limit = chunk_num * CHUNK_SIZE +
197 part_table[PART_DOWN].mem.size;
198 partition.mem.start = addr;
199 wl1271_set_partition(wl, &partition);
202 /* 10.3 upload the chunk */
203 addr = dest + chunk_num * CHUNK_SIZE;
204 p = buf + chunk_num * CHUNK_SIZE;
205 memcpy(chunk, p, CHUNK_SIZE);
206 wl1271_debug(DEBUG_BOOT, "uploading fw chunk 0x%p to 0x%x",
208 wl1271_write(wl, addr, chunk, CHUNK_SIZE, false);
213 /* 10.4 upload the last chunk */
214 addr = dest + chunk_num * CHUNK_SIZE;
215 p = buf + chunk_num * CHUNK_SIZE;
216 memcpy(chunk, p, fw_data_len % CHUNK_SIZE);
217 wl1271_debug(DEBUG_BOOT, "uploading fw last chunk (%zd B) 0x%p to 0x%x",
218 fw_data_len % CHUNK_SIZE, p, addr);
219 wl1271_write(wl, addr, chunk, fw_data_len % CHUNK_SIZE, false);
225 static int wl1271_boot_upload_firmware(struct wl1271 *wl)
227 u32 chunks, addr, len;
232 chunks = be32_to_cpup((__be32 *) fw);
235 wl1271_debug(DEBUG_BOOT, "firmware chunks to be uploaded: %u", chunks);
238 addr = be32_to_cpup((__be32 *) fw);
240 len = be32_to_cpup((__be32 *) fw);
244 wl1271_info("firmware chunk too long: %u", len);
247 wl1271_debug(DEBUG_BOOT, "chunk %d addr 0x%x len %u",
249 ret = wl1271_boot_upload_firmware_chunk(wl, fw, len, addr);
258 static int wl1271_boot_upload_nvs(struct wl1271 *wl)
260 size_t nvs_len, burst_len;
263 u8 *nvs_ptr, *nvs_aligned;
268 if (wl->chip.id == CHIP_ID_1283_PG20) {
269 struct wl128x_nvs_file *nvs = (struct wl128x_nvs_file *)wl->nvs;
271 if (wl->nvs_len == sizeof(struct wl128x_nvs_file)) {
272 if (nvs->general_params.dual_mode_select)
273 wl->enable_11a = true;
275 wl1271_error("nvs size is not as expected: %zu != %zu",
277 sizeof(struct wl128x_nvs_file));
284 /* only the first part of the NVS needs to be uploaded */
285 nvs_len = sizeof(nvs->nvs);
286 nvs_ptr = (u8 *)nvs->nvs;
289 struct wl1271_nvs_file *nvs =
290 (struct wl1271_nvs_file *)wl->nvs;
292 * FIXME: the LEGACY NVS image support (NVS's missing the 5GHz
293 * band configurations) can be removed when those NVS files stop
296 if (wl->nvs_len == sizeof(struct wl1271_nvs_file) ||
297 wl->nvs_len == WL1271_INI_LEGACY_NVS_FILE_SIZE) {
298 if (nvs->general_params.dual_mode_select)
299 wl->enable_11a = true;
302 if (wl->nvs_len != sizeof(struct wl1271_nvs_file) &&
303 (wl->nvs_len != WL1271_INI_LEGACY_NVS_FILE_SIZE ||
305 wl1271_error("nvs size is not as expected: %zu != %zu",
306 wl->nvs_len, sizeof(struct wl1271_nvs_file));
313 /* only the first part of the NVS needs to be uploaded */
314 nvs_len = sizeof(nvs->nvs);
315 nvs_ptr = (u8 *) nvs->nvs;
318 /* update current MAC address to NVS */
319 nvs_ptr[11] = wl->mac_addr[0];
320 nvs_ptr[10] = wl->mac_addr[1];
321 nvs_ptr[6] = wl->mac_addr[2];
322 nvs_ptr[5] = wl->mac_addr[3];
323 nvs_ptr[4] = wl->mac_addr[4];
324 nvs_ptr[3] = wl->mac_addr[5];
327 * Layout before the actual NVS tables:
328 * 1 byte : burst length.
329 * 2 bytes: destination address.
330 * n bytes: data to burst copy.
332 * This is ended by a 0 length, then the NVS tables.
335 /* FIXME: Do we need to check here whether the LSB is 1? */
337 burst_len = nvs_ptr[0];
338 dest_addr = (nvs_ptr[1] & 0xfe) | ((u32)(nvs_ptr[2] << 8));
341 * Due to our new wl1271_translate_reg_addr function,
342 * we need to add the REGISTER_BASE to the destination
344 dest_addr += REGISTERS_BASE;
346 /* We move our pointer to the data */
349 for (i = 0; i < burst_len; i++) {
350 val = (nvs_ptr[0] | (nvs_ptr[1] << 8)
351 | (nvs_ptr[2] << 16) | (nvs_ptr[3] << 24));
353 wl1271_debug(DEBUG_BOOT,
354 "nvs burst write 0x%x: 0x%x",
356 wl1271_write32(wl, dest_addr, val);
364 * We've reached the first zero length, the first NVS table
365 * is located at an aligned offset which is at least 7 bytes further.
366 * NOTE: The wl->nvs->nvs element must be first, in order to
367 * simplify the casting, we assume it is at the beginning of
368 * the wl->nvs structure.
370 nvs_ptr = (u8 *)wl->nvs +
371 ALIGN(nvs_ptr - (u8 *)wl->nvs + 7, 4);
372 nvs_len -= nvs_ptr - (u8 *)wl->nvs;
374 /* Now we must set the partition correctly */
375 wl1271_set_partition(wl, &part_table[PART_WORK]);
377 /* Copy the NVS tables to a new block to ensure alignment */
378 nvs_aligned = kmemdup(nvs_ptr, nvs_len, GFP_KERNEL);
382 /* And finally we upload the NVS tables */
383 wl1271_write(wl, CMD_MBOX_ADDRESS, nvs_aligned, nvs_len, false);
389 static void wl1271_boot_enable_interrupts(struct wl1271 *wl)
391 wl1271_enable_interrupts(wl);
392 wl1271_write32(wl, ACX_REG_INTERRUPT_MASK,
393 WL1271_ACX_INTR_ALL & ~(WL1271_INTR_MASK));
394 wl1271_write32(wl, HI_CFG, HI_CFG_DEF_VAL);
397 static int wl1271_boot_soft_reset(struct wl1271 *wl)
399 unsigned long timeout;
402 /* perform soft reset */
403 wl1271_write32(wl, ACX_REG_SLV_SOFT_RESET, ACX_SLV_SOFT_RESET_BIT);
405 /* SOFT_RESET is self clearing */
406 timeout = jiffies + usecs_to_jiffies(SOFT_RESET_MAX_TIME);
408 boot_data = wl1271_read32(wl, ACX_REG_SLV_SOFT_RESET);
409 wl1271_debug(DEBUG_BOOT, "soft reset bootdata 0x%x", boot_data);
410 if ((boot_data & ACX_SLV_SOFT_RESET_BIT) == 0)
413 if (time_after(jiffies, timeout)) {
414 /* 1.2 check pWhalBus->uSelfClearTime if the
415 * timeout was reached */
416 wl1271_error("soft reset timeout");
420 udelay(SOFT_RESET_STALL_TIME);
424 wl1271_write32(wl, ENABLE, 0x0);
426 /* disable auto calibration on start*/
427 wl1271_write32(wl, SPARE_A2, 0xffff);
432 static int wl1271_boot_run_firmware(struct wl1271 *wl)
437 wl1271_boot_set_ecpu_ctrl(wl, ECPU_CONTROL_HALT);
439 chip_id = wl1271_read32(wl, CHIP_ID_B);
441 wl1271_debug(DEBUG_BOOT, "chip id after firmware boot: 0x%x", chip_id);
443 if (chip_id != wl->chip.id) {
444 wl1271_error("chip id doesn't match after firmware boot");
448 /* wait for init to complete */
450 while (loop++ < INIT_LOOP) {
451 udelay(INIT_LOOP_DELAY);
452 intr = wl1271_read32(wl, ACX_REG_INTERRUPT_NO_CLEAR);
454 if (intr == 0xffffffff) {
455 wl1271_error("error reading hardware complete "
459 /* check that ACX_INTR_INIT_COMPLETE is enabled */
460 else if (intr & WL1271_ACX_INTR_INIT_COMPLETE) {
461 wl1271_write32(wl, ACX_REG_INTERRUPT_ACK,
462 WL1271_ACX_INTR_INIT_COMPLETE);
467 if (loop > INIT_LOOP) {
468 wl1271_error("timeout waiting for the hardware to "
469 "complete initialization");
473 /* get hardware config command mail box */
474 wl->cmd_box_addr = wl1271_read32(wl, REG_COMMAND_MAILBOX_PTR);
476 /* get hardware config event mail box */
477 wl->event_box_addr = wl1271_read32(wl, REG_EVENT_MAILBOX_PTR);
479 /* set the working partition to its "running" mode offset */
480 wl1271_set_partition(wl, &part_table[PART_WORK]);
482 wl1271_debug(DEBUG_MAILBOX, "cmd_box_addr 0x%x event_box_addr 0x%x",
483 wl->cmd_box_addr, wl->event_box_addr);
485 wl1271_boot_fw_version(wl);
488 * in case of full asynchronous mode the firmware event must be
489 * ready to receive event from the command mailbox
492 /* unmask required mbox events */
493 wl->event_mask = BSS_LOSE_EVENT_ID |
494 SCAN_COMPLETE_EVENT_ID |
496 DISCONNECT_EVENT_COMPLETE_ID |
497 RSSI_SNR_TRIGGER_0_EVENT_ID |
498 PSPOLL_DELIVERY_FAILURE_EVENT_ID |
499 SOFT_GEMINI_SENSE_EVENT_ID |
500 PERIODIC_SCAN_REPORT_EVENT_ID |
501 PERIODIC_SCAN_COMPLETE_EVENT_ID |
502 DUMMY_PACKET_EVENT_ID |
503 PEER_REMOVE_COMPLETE_EVENT_ID |
504 BA_SESSION_RX_CONSTRAINT_EVENT_ID |
505 REMAIN_ON_CHANNEL_COMPLETE_EVENT_ID |
506 INACTIVE_STA_EVENT_ID |
507 MAX_TX_RETRY_EVENT_ID |
508 CHANNEL_SWITCH_COMPLETE_EVENT_ID;
510 ret = wl1271_event_unmask(wl);
512 wl1271_error("EVENT mask setting failed");
516 wl1271_event_mbox_config(wl);
518 /* firmware startup completed */
522 static int wl1271_boot_write_irq_polarity(struct wl1271 *wl)
526 polarity = wl1271_top_reg_read(wl, OCP_REG_POLARITY);
528 /* We use HIGH polarity, so unset the LOW bit */
529 polarity &= ~POLARITY_LOW;
530 wl1271_top_reg_write(wl, OCP_REG_POLARITY, polarity);
535 static void wl1271_boot_hw_version(struct wl1271 *wl)
539 if (wl->chip.id == CHIP_ID_1283_PG20)
540 fuse = wl1271_top_reg_read(wl, WL128X_REG_FUSE_DATA_2_1);
542 fuse = wl1271_top_reg_read(wl, WL127X_REG_FUSE_DATA_2_1);
543 fuse = (fuse & PG_VER_MASK) >> PG_VER_OFFSET;
545 wl->hw_pg_ver = (s8)fuse;
548 static int wl128x_switch_tcxo_to_fref(struct wl1271 *wl)
552 /* Mask bits [2] & [8:4] in the sys_clk_cfg register */
553 spare_reg = wl1271_top_reg_read(wl, WL_SPARE_REG);
554 if (spare_reg == 0xFFFF)
556 spare_reg |= (BIT(3) | BIT(5) | BIT(6));
557 wl1271_top_reg_write(wl, WL_SPARE_REG, spare_reg);
559 /* Enable FREF_CLK_REQ & mux MCS and coex PLLs to FREF */
560 wl1271_top_reg_write(wl, SYS_CLK_CFG_REG,
561 WL_CLK_REQ_TYPE_PG2 | MCS_PLL_CLK_SEL_FREF);
563 /* Delay execution for 15msec, to let the HW settle */
569 static bool wl128x_is_tcxo_valid(struct wl1271 *wl)
573 tcxo_detection = wl1271_top_reg_read(wl, TCXO_CLK_DETECT_REG);
574 if (tcxo_detection & TCXO_DET_FAILED)
580 static bool wl128x_is_fref_valid(struct wl1271 *wl)
584 fref_detection = wl1271_top_reg_read(wl, FREF_CLK_DETECT_REG);
585 if (fref_detection & FREF_CLK_DETECT_FAIL)
591 static int wl128x_manually_configure_mcs_pll(struct wl1271 *wl)
593 wl1271_top_reg_write(wl, MCS_PLL_M_REG, MCS_PLL_M_REG_VAL);
594 wl1271_top_reg_write(wl, MCS_PLL_N_REG, MCS_PLL_N_REG_VAL);
595 wl1271_top_reg_write(wl, MCS_PLL_CONFIG_REG, MCS_PLL_CONFIG_REG_VAL);
600 static int wl128x_configure_mcs_pll(struct wl1271 *wl, int clk)
606 /* Mask bits [3:1] in the sys_clk_cfg register */
607 spare_reg = wl1271_top_reg_read(wl, WL_SPARE_REG);
608 if (spare_reg == 0xFFFF)
611 wl1271_top_reg_write(wl, WL_SPARE_REG, spare_reg);
613 /* Handle special cases of the TCXO clock */
614 if (wl->tcxo_clock == WL12XX_TCXOCLOCK_16_8 ||
615 wl->tcxo_clock == WL12XX_TCXOCLOCK_33_6)
616 return wl128x_manually_configure_mcs_pll(wl);
618 /* Set the input frequency according to the selected clock source */
619 input_freq = (clk & 1) + 1;
621 pll_config = wl1271_top_reg_read(wl, MCS_PLL_CONFIG_REG);
622 if (pll_config == 0xFFFF)
624 pll_config |= (input_freq << MCS_SEL_IN_FREQ_SHIFT);
625 pll_config |= MCS_PLL_ENABLE_HP;
626 wl1271_top_reg_write(wl, MCS_PLL_CONFIG_REG, pll_config);
632 * WL128x has two clocks input - TCXO and FREF.
633 * TCXO is the main clock of the device, while FREF is used to sync
634 * between the GPS and the cellular modem.
635 * In cases where TCXO is 32.736MHz or 16.368MHz, the FREF will be used
636 * as the WLAN/BT main clock.
638 static int wl128x_boot_clk(struct wl1271 *wl, int *selected_clock)
642 /* For XTAL-only modes, FREF will be used after switching from TCXO */
643 if (wl->ref_clock == WL12XX_REFCLOCK_26_XTAL ||
644 wl->ref_clock == WL12XX_REFCLOCK_38_XTAL) {
645 if (!wl128x_switch_tcxo_to_fref(wl))
650 /* Query the HW, to determine which clock source we should use */
651 sys_clk_cfg = wl1271_top_reg_read(wl, SYS_CLK_CFG_REG);
652 if (sys_clk_cfg == 0xFFFF)
654 if (sys_clk_cfg & PRCM_CM_EN_MUX_WLAN_FREF)
657 /* If TCXO is either 32.736MHz or 16.368MHz, switch to FREF */
658 if (wl->tcxo_clock == WL12XX_TCXOCLOCK_16_368 ||
659 wl->tcxo_clock == WL12XX_TCXOCLOCK_32_736) {
660 if (!wl128x_switch_tcxo_to_fref(wl))
665 /* TCXO clock is selected */
666 if (!wl128x_is_tcxo_valid(wl))
668 *selected_clock = wl->tcxo_clock;
672 /* FREF clock is selected */
673 if (!wl128x_is_fref_valid(wl))
675 *selected_clock = wl->ref_clock;
678 return wl128x_configure_mcs_pll(wl, *selected_clock);
681 static int wl127x_boot_clk(struct wl1271 *wl)
686 if (((wl->hw_pg_ver & PG_MAJOR_VER_MASK) >> PG_MAJOR_VER_OFFSET) < 3)
687 wl->quirks |= WL12XX_QUIRK_END_OF_TRANSACTION;
689 if (wl->ref_clock == CONF_REF_CLK_19_2_E ||
690 wl->ref_clock == CONF_REF_CLK_38_4_E ||
691 wl->ref_clock == CONF_REF_CLK_38_4_M_XTAL)
692 /* ref clk: 19.2/38.4/38.4-XTAL */
694 else if (wl->ref_clock == CONF_REF_CLK_26_E ||
695 wl->ref_clock == CONF_REF_CLK_52_E)
701 if (wl->ref_clock != CONF_REF_CLK_19_2_E) {
703 /* Set clock type (open drain) */
704 val = wl1271_top_reg_read(wl, OCP_REG_CLK_TYPE);
705 val &= FREF_CLK_TYPE_BITS;
706 wl1271_top_reg_write(wl, OCP_REG_CLK_TYPE, val);
708 /* Set clock pull mode (no pull) */
709 val = wl1271_top_reg_read(wl, OCP_REG_CLK_PULL);
711 wl1271_top_reg_write(wl, OCP_REG_CLK_PULL, val);
714 /* Set clock polarity */
715 val = wl1271_top_reg_read(wl, OCP_REG_CLK_POLARITY);
716 val &= FREF_CLK_POLARITY_BITS;
717 val |= CLK_REQ_OUTN_SEL;
718 wl1271_top_reg_write(wl, OCP_REG_CLK_POLARITY, val);
721 wl1271_write32(wl, PLL_PARAMETERS, clk);
723 pause = wl1271_read32(wl, PLL_PARAMETERS);
725 wl1271_debug(DEBUG_BOOT, "pause1 0x%x", pause);
727 pause &= ~(WU_COUNTER_PAUSE_VAL);
728 pause |= WU_COUNTER_PAUSE_VAL;
729 wl1271_write32(wl, WU_COUNTER_PAUSE, pause);
734 /* uploads NVS and firmware */
735 int wl1271_load_firmware(struct wl1271 *wl)
739 int selected_clock = -1;
741 wl1271_boot_hw_version(wl);
743 if (wl->chip.id == CHIP_ID_1283_PG20) {
744 ret = wl128x_boot_clk(wl, &selected_clock);
748 ret = wl127x_boot_clk(wl);
753 /* Continue the ELP wake up sequence */
754 wl1271_write32(wl, WELP_ARM_COMMAND, WELP_ARM_COMMAND_VAL);
757 wl1271_set_partition(wl, &part_table[PART_DRPW]);
759 /* Read-modify-write DRPW_SCRATCH_START register (see next state)
760 to be used by DRPw FW. The RTRIM value will be added by the FW
761 before taking DRPw out of reset */
763 wl1271_debug(DEBUG_BOOT, "DRPW_SCRATCH_START %08x", DRPW_SCRATCH_START);
764 clk = wl1271_read32(wl, DRPW_SCRATCH_START);
766 wl1271_debug(DEBUG_BOOT, "clk2 0x%x", clk);
768 if (wl->chip.id == CHIP_ID_1283_PG20) {
769 clk |= ((selected_clock & 0x3) << 1) << 4;
771 clk |= (wl->ref_clock << 1) << 4;
774 wl1271_write32(wl, DRPW_SCRATCH_START, clk);
776 wl1271_set_partition(wl, &part_table[PART_WORK]);
778 /* Disable interrupts */
779 wl1271_write32(wl, ACX_REG_INTERRUPT_MASK, WL1271_ACX_INTR_ALL);
781 ret = wl1271_boot_soft_reset(wl);
785 /* 2. start processing NVS file */
786 ret = wl1271_boot_upload_nvs(wl);
790 /* write firmware's last address (ie. it's length) to
791 * ACX_EEPROMLESS_IND_REG */
792 wl1271_debug(DEBUG_BOOT, "ACX_EEPROMLESS_IND_REG");
794 wl1271_write32(wl, ACX_EEPROMLESS_IND_REG, ACX_EEPROMLESS_IND_REG);
796 tmp = wl1271_read32(wl, CHIP_ID_B);
798 wl1271_debug(DEBUG_BOOT, "chip id 0x%x", tmp);
800 /* 6. read the EEPROM parameters */
801 tmp = wl1271_read32(wl, SCR_PAD2);
803 /* WL1271: The reference driver skips steps 7 to 10 (jumps directly
806 if (wl->chip.id == CHIP_ID_1283_PG20)
807 wl1271_top_reg_write(wl, SDIO_IO_DS, wl->conf.hci_io_ds);
809 ret = wl1271_boot_upload_firmware(wl);
816 EXPORT_SYMBOL_GPL(wl1271_load_firmware);
818 int wl1271_boot(struct wl1271 *wl)
822 /* upload NVS and firmware */
823 ret = wl1271_load_firmware(wl);
827 /* 10.5 start firmware */
828 ret = wl1271_boot_run_firmware(wl);
832 ret = wl1271_boot_write_irq_polarity(wl);
836 wl1271_write32(wl, ACX_REG_INTERRUPT_MASK,
837 WL1271_ACX_ALL_EVENTS_VECTOR);
839 /* Enable firmware interrupts now */
840 wl1271_boot_enable_interrupts(wl);
842 wl1271_event_mbox_config(wl);