2 # USB Network devices configuration
4 comment "Networking support is needed for USB Network Adapter support"
7 menu "USB Network Adapters"
11 tristate "USB CATC NetMate-based Ethernet device support (EXPERIMENTAL)"
12 depends on EXPERIMENTAL
15 Say Y if you want to use one of the following 10Mbps USB Ethernet
16 device based on the EL1210A chip. Supported devices are:
23 This driver makes the adapter appear as a normal Ethernet interface,
24 typically on eth0, if it is the only ethernet device, or perhaps on
25 eth1, if you have a PCI or ISA ethernet card installed.
27 To compile this driver as a module, choose M here: the
28 module will be called catc.
31 tristate "USB KLSI KL5USB101-based ethernet device support"
33 Say Y here if you want to use one of the following 10Mbps only
34 USB Ethernet adapters based on the KLSI KL5KUSB101B chipset:
38 ASANTE USB To Ethernet Adapter
39 AOX Endpoints USB Ethernet
41 D-Link DSB-650C and DU-E10
42 Entrega / Portgear E45
44 Jaton USB Ethernet Device Adapter
45 Kingston Technology USB Ethernet Adapter
47 Mobility USB-Ethernet Adapter
49 Peracom Enet and Enet2
50 Portsmith Express Ethernet Adapter
53 Sony Vaio port extender
55 This driver is likely to work with most 10Mbps only USB Ethernet
56 adapters, including some "no brand" devices. It does NOT work on
57 SmartBridges smartNIC or on Belkin F5U111 devices - you should use
58 the CATC NetMate driver for those. If you are not sure which one
59 you need, select both, and the correct one should be selected for
62 This driver makes the adapter appear as a normal Ethernet interface,
63 typically on eth0, if it is the only ethernet device, or perhaps on
64 eth1, if you have a PCI or ISA ethernet card installed.
66 To compile this driver as a module, choose M here: the
67 module will be called kaweth.
70 tristate "USB Pegasus/Pegasus-II based ethernet device support"
74 Say Y here if you know you have Pegasus or Pegasus-II based adapter.
75 If in doubt then look at <file:drivers/net/usb/pegasus.h> for the
76 complete list of supported devices.
78 If your particular adapter is not in the list and you are _sure_ it
79 is Pegasus or Pegasus II based then send me
80 <petkan@users.sourceforge.net> vendor and device IDs.
82 To compile this driver as a module, choose M here: the
83 module will be called pegasus.
86 tristate "USB RTL8150 based ethernet device support (EXPERIMENTAL)"
87 depends on EXPERIMENTAL
91 Say Y here if you have RTL8150 based usb-ethernet adapter.
92 Send me <petkan@users.sourceforge.net> any comments you may have.
93 You can also check for updates at <http://pegasus2.sourceforge.net/>.
95 To compile this driver as a module, choose M here: the
96 module will be called rtl8150.
99 tristate "Multi-purpose USB Networking Framework"
103 This driver supports several kinds of network links over USB,
104 with "minidrivers" built around a common network driver core
105 that supports deep queues for efficient transfers. (This gives
106 better performance with small packets and at high speeds).
108 The USB host runs "usbnet", and the other end of the link might be:
110 - Another USB host, when using USB "network" or "data transfer"
111 cables. These are often used to network laptops to PCs, like
112 "Laplink" parallel cables or some motherboards. These rely
113 on specialized chips from many suppliers.
115 - An intelligent USB gadget, perhaps embedding a Linux system.
116 These include PDAs running Linux (iPaq, Yopy, Zaurus, and
117 others), and devices that interoperate using the standard
118 CDC-Ethernet specification (including many cable modems).
120 - Network adapter hardware (like those for 10/100 Ethernet) which
121 uses this driver framework.
123 The link will appear with a name like "usb0", when the link is
124 a two-node link, or "eth0" for most CDC-Ethernet devices. Those
125 two-node links are most easily managed with Ethernet Bridging
126 (CONFIG_BRIDGE) instead of routing.
128 For more information see <http://www.linux-usb.org/usbnet/>.
130 To compile this driver as a module, choose M here: the
131 module will be called usbnet.
133 config USB_NET_AX8817X
134 tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters"
135 depends on USB_USBNET
140 This option adds support for ASIX AX88xxx based USB 2.0
141 10/100 Ethernet adapters.
143 This driver should work with at least the following devices:
146 * Billionton Systems, USB2AR
148 * Corega FEther USB2-TX
154 * Intellinet USB 2.0 Ethernet
155 * ST Lab USB 2.0 Ethernet
158 This driver creates an interface named "ethX", where X depends on
159 what other networking devices you have in use.
161 config USB_NET_CDCETHER
162 tristate "CDC Ethernet support (smart devices such as cable modems)"
163 depends on USB_USBNET
166 This option supports devices conforming to the Communication Device
167 Class (CDC) Ethernet Control Model, a specification that's easy to
168 implement in device firmware. The CDC specifications are available
169 from <http://www.usb.org/>.
171 CDC Ethernet is an implementation option for DOCSIS cable modems
172 that support USB connectivity, used for non-Microsoft USB hosts.
173 The Linux-USB CDC Ethernet Gadget driver is an open implementation.
174 This driver should work with at least the following devices:
176 * Dell Wireless 5530 HSPA
177 * Ericsson PipeRider (all variants)
178 * Ericsson Mobile Broadband Module (all variants)
179 * Motorola (DM100 and SB4100)
180 * Broadcom Cable Modem (reference design)
181 * Toshiba (PCX1100U and F3507g/F3607gw)
184 This driver creates an interface named "ethX", where X depends on
185 what other networking devices you have in use. However, if the
186 IEEE 802 "local assignment" bit is set in the address, a "usbX"
187 name is used instead.
189 config USB_NET_CDC_EEM
190 tristate "CDC EEM support"
191 depends on USB_USBNET && EXPERIMENTAL
193 This option supports devices conforming to the Communication Device
194 Class (CDC) Ethernet Emulation Model, a specification that's easy to
195 implement in device firmware. The CDC EEM specifications are available
196 from <http://www.usb.org/>.
198 This driver creates an interface named "ethX", where X depends on
199 what other networking devices you have in use. However, if the
200 IEEE 802 "local assignment" bit is set in the address, a "usbX"
201 name is used instead.
203 config USB_NET_CDC_NCM
204 tristate "CDC NCM support"
205 depends on USB_USBNET
208 This driver provides support for CDC NCM (Network Control Model
209 Device USB Class Specification). The CDC NCM specification is
210 available from <http://www.usb.org/>.
212 Say "y" to link the driver statically, or "m" to build a
213 dynamically linked module.
215 This driver should work with at least the following devices:
216 * ST-Ericsson M700 LTE FDD/TDD Mobile Broadband Modem (ref. design)
217 * ST-Ericsson M5730 HSPA+ Mobile Broadband Modem (reference design)
218 * ST-Ericsson M570 HSPA+ Mobile Broadband Modem (reference design)
219 * ST-Ericsson M343 HSPA Mobile Broadband Modem (reference design)
220 * Ericsson F5521gw Mobile Broadband Module
222 config USB_NET_CDC_MBIM
223 tristate "CDC MBIM support"
224 depends on USB_USBNET
226 select USB_NET_CDC_NCM
228 This driver provides support for CDC MBIM (Mobile Broadband
229 Interface Model) devices. The CDC MBIM specification is
230 available from <http://www.usb.org/>.
232 MBIM devices require configuration using the management
233 protocol defined by the MBIM specification. This driver
234 provides unfiltered access to the MBIM control channel
235 through the associated /dev/cdc-wdmx character device.
237 To compile this driver as a module, choose M here: the
238 module will be called cdc_mbim.
240 config USB_NET_DM9601
241 tristate "Davicom DM9601 based USB 1.1 10/100 ethernet devices"
242 depends on USB_USBNET
245 This option adds support for Davicom DM9601 based USB 1.1
246 10/100 Ethernet adapters.
248 config USB_NET_SMSC75XX
249 tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices"
250 depends on USB_USBNET
253 This option adds support for SMSC LAN95XX based USB 2.0
254 Gigabit Ethernet adapters.
256 config USB_NET_SMSC95XX
257 tristate "SMSC LAN95XX based USB 2.0 10/100 ethernet devices"
258 depends on USB_USBNET
263 This option adds support for SMSC LAN95XX based USB 2.0
264 10/100 Ethernet adapters.
266 config USB_NET_GL620A
267 tristate "GeneSys GL620USB-A based cables"
268 depends on USB_USBNET
270 Choose this option if you're using a host-to-host cable,
271 or PC2PC motherboard, with this chip.
273 Note that the half-duplex "GL620USB" is not supported.
275 config USB_NET_NET1080
276 tristate "NetChip 1080 based cables (Laplink, ...)"
278 depends on USB_USBNET
280 Choose this option if you're using a host-to-host cable based
281 on this design: one NetChip 1080 chip and supporting logic,
282 optionally with LEDs that indicate traffic
285 tristate "Prolific PL-2301/2302/25A1 based cables"
286 # if the handshake/init/reset problems, from original 'plusb',
287 # are ever resolved ... then remove "experimental"
288 depends on USB_USBNET && EXPERIMENTAL
290 Choose this option if you're using a host-to-host cable
291 with one of these chips.
293 config USB_NET_MCS7830
294 tristate "MosChip MCS7830 based Ethernet adapters"
295 depends on USB_USBNET
297 Choose this option if you're using a 10/100 Ethernet USB2
298 adapter based on the MosChip 7830 controller. This includes
299 adapters marketed under the DeLOCK brand.
301 config USB_NET_RNDIS_HOST
302 tristate "Host for RNDIS and ActiveSync devices (EXPERIMENTAL)"
303 depends on USB_USBNET && EXPERIMENTAL
304 select USB_NET_CDCETHER
306 This option enables hosting "Remote NDIS" USB networking links,
307 as encouraged by Microsoft (instead of CDC Ethernet!) for use in
308 various devices that may only support this protocol. A variant
309 of this protocol (with even less public documentation) seems to
310 be at the root of Microsoft's "ActiveSync" too.
312 Avoid using this protocol unless you have no better options.
313 The protocol specification is incomplete, and is controlled by
314 (and for) Microsoft; it isn't an "Open" ecosystem or market.
316 config USB_NET_CDC_SUBSET
317 tristate "Simple USB Network Links (CDC Ethernet subset)"
318 depends on USB_USBNET
321 This driver module supports USB network devices that can work
322 without any device-specific information. Select it if you have
323 one of these drivers.
325 Note that while many USB host-to-host cables can work in this mode,
326 that may mean not being able to talk to Win32 systems or more
327 commonly not being able to handle certain events (like replugging
328 the host on the other end) very well. Also, these devices will
329 not generally have permanently assigned Ethernet addresses.
332 boolean "ALi M5632 based 'USB 2.0 Data Link' cables"
333 depends on USB_NET_CDC_SUBSET
335 Choose this option if you're using a host-to-host cable
336 based on this design, which supports USB 2.0 high speed.
339 boolean "AnchorChips 2720 based cables (Xircom PGUNET, ...)"
340 depends on USB_NET_CDC_SUBSET
342 Choose this option if you're using a host-to-host cable
343 based on this design. Note that AnchorChips is now a
347 boolean "eTEK based host-to-host cables (Advance, Belkin, ...)"
348 depends on USB_NET_CDC_SUBSET
351 Choose this option if you're using a host-to-host cable
352 based on this design: two NetChip 2890 chips and an Atmel
353 microcontroller, with LEDs that indicate traffic.
356 boolean "Embedded ARM Linux links (iPaq, ...)"
357 depends on USB_NET_CDC_SUBSET
360 Choose this option to support the "usb-eth" networking driver
361 used by most of the ARM Linux community with device controllers
362 such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities
363 in some PXA versions of the "blob" boot loader.
365 Linux-based "Gumstix" PXA-25x based systems use this protocol
366 to talk with other Linux systems.
368 Although the ROMs shipped with Sharp Zaurus products use a
369 different link level framing protocol, you can have them use
370 this simpler protocol by installing a different kernel.
373 boolean "Epson 2888 based firmware (DEVELOPMENT)"
374 depends on USB_NET_CDC_SUBSET
376 Choose this option to support the usb networking links used
377 by some sample firmware from Epson.
380 boolean "KT Technology KC2190 based cables (InstaNet)"
381 depends on USB_NET_CDC_SUBSET && EXPERIMENTAL
383 Choose this option if you're using a host-to-host cable
384 with one of these chips.
386 config USB_NET_ZAURUS
387 tristate "Sharp Zaurus (stock ROMs) and compatible"
388 depends on USB_USBNET
389 select USB_NET_CDCETHER
393 Choose this option to support the usb networking links used by
394 Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500.
395 This also supports some related device firmware, as used in some
396 PDAs from Olympus and some cell phones from Motorola.
398 If you install an alternate image, such as the Linux 2.6 based
399 versions of OpenZaurus, you should no longer need to support this
400 protocol. Only the "eth-fd" or "net_fd" drivers in these devices
401 really need this non-conformant variant of CDC Ethernet (or in
402 some cases CDC MDLM) protocol, not "g_ether".
404 config USB_NET_CX82310_ETH
405 tristate "Conexant CX82310 USB ethernet port"
406 depends on USB_USBNET
408 Choose this option if you're using a Conexant CX82310-based ADSL
409 router with USB ethernet port. This driver is for routers only,
410 it will not work with ADSL modems (use cxacru driver instead).
412 config USB_NET_KALMIA
413 tristate "Samsung Kalmia based LTE USB modem"
414 depends on USB_USBNET
416 Choose this option if you have a Samsung Kalmia based USB modem
419 To compile this driver as a module, choose M here: the
420 module will be called kalmia.
422 config USB_NET_QMI_WWAN
423 tristate "QMI WWAN driver for Qualcomm MSM based 3G and LTE modems"
424 depends on USB_USBNET
427 Support WWAN LTE/3G devices based on Qualcomm Mobile Data Modem
428 (MDM) chipsets. Examples of such devices are
431 This driver will only drive the ethernet part of the chips.
432 The devices require additional configuration to be usable.
433 Multiple management interfaces with linux drivers are
436 * option: AT commands on /dev/ttyUSBx
437 * cdc-wdm: Qualcomm MSM Interface (QMI) protocol on /dev/cdc-wdmx
439 A modem manager with support for QMI is recommended.
441 To compile this driver as a module, choose M here: the
442 module will be called qmi_wwan.
445 tristate "Option USB High Speed Mobile Devices"
446 depends on USB && RFKILL
449 Choose this option if you have an Option HSDPA/HSUPA card.
450 These cards support downlink speeds of 7.2Mbps or greater.
452 To compile this driver as a module, choose M here: the
453 module will be called hso.
455 config USB_NET_INT51X1
456 tristate "Intellon PLC based usb adapter"
457 depends on USB_USBNET
459 Choose this option if you're using a 14Mb USB-based PLC
460 (Powerline Communications) solution with an Intellon
461 INT51x1/INT5200 chip, like the "devolo dLan duo".
463 config USB_CDC_PHONET
464 tristate "CDC Phonet support"
467 Choose this option to support the Phonet interface to a Nokia
468 cellular modem, as found on most Nokia handsets with the
469 "PC suite" USB profile.
472 tristate "Apple iPhone USB Ethernet driver"
475 Module used to share Internet connection (tethering) from your
476 iPhone (Original, 3G and 3GS) to your system.
477 Note that you need userspace libraries and programs that are needed
478 to pair your device with your system and that understand the iPhone
481 For more information: http://giagio.com/wiki/moin.cgi/iPhoneEthernetDriver
483 config USB_SIERRA_NET
484 tristate "USB-to-WWAN Driver for Sierra Wireless modems"
485 depends on USB_USBNET
487 Choose this option if you have a Sierra Wireless USB-to-WWAN device.
489 To compile this driver as a module, choose M here: the
490 module will be called sierra_net.
493 tristate "LG VL600 modem dongle"
494 depends on USB_NET_CDCETHER
497 Select this if you want to use an LG Electronics 4G/LTE usb modem
498 called VL600. This driver only handles the ethernet
499 interface exposed by the modem firmware. To establish a connection
500 you will first need a userspace program that sends the right
501 command to the modem through its CDC ACM port, and most
502 likely also a DHCP client. See this thread about using the
503 4G modem from Verizon:
505 http://ubuntuforums.org/showpost.php?p=10589647&postcount=17