1 /************************************************************************
2 * s2io.c: A Linux PCI-X Ethernet driver for Neterion 10GbE Server NIC
3 * Copyright(c) 2002-2010 Exar Corp.
5 * This software may be used and distributed according to the terms of
6 * the GNU General Public License (GPL), incorporated herein by reference.
7 * Drivers based on or derived from this code fall under the GPL and must
8 * retain the authorship, copyright and license notice. This file is not
9 * a complete program and may only be used when the entire operating
10 * system is licensed under the GPL.
11 * See the file COPYING in this distribution for more information.
14 * Jeff Garzik : For pointing out the improper error condition
15 * check in the s2io_xmit routine and also some
16 * issues in the Tx watch dog function. Also for
17 * patiently answering all those innumerable
18 * questions regaring the 2.6 porting issues.
19 * Stephen Hemminger : Providing proper 2.6 porting mechanism for some
20 * macros available only in 2.6 Kernel.
21 * Francois Romieu : For pointing out all code part that were
22 * deprecated and also styling related comments.
23 * Grant Grundler : For helping me get rid of some Architecture
25 * Christopher Hellwig : Some more 2.6 specific issues in the driver.
27 * The module loadable parameters that are supported by the driver and a brief
28 * explanation of all the variables.
30 * rx_ring_num : This can be used to program the number of receive rings used
32 * rx_ring_sz: This defines the number of receive blocks each ring can have.
33 * This is also an array of size 8.
34 * rx_ring_mode: This defines the operation mode of all 8 rings. The valid
36 * tx_fifo_num: This defines the number of Tx FIFOs thats used int the driver.
37 * tx_fifo_len: This too is an array of 8. Each element defines the number of
38 * Tx descriptors that can be associated with each corresponding FIFO.
39 * intr_type: This defines the type of interrupt. The values can be 0(INTA),
40 * 2(MSI_X). Default value is '2(MSI_X)'
41 * lro_max_pkts: This parameter defines maximum number of packets can be
42 * aggregated as a single large packet
43 * napi: This parameter used to enable/disable NAPI (polling Rx)
44 * Possible values '1' for enable and '0' for disable. Default is '1'
45 * ufo: This parameter used to enable/disable UDP Fragmentation Offload(UFO)
46 * Possible values '1' for enable and '0' for disable. Default is '0'
47 * vlan_tag_strip: This can be used to enable or disable vlan stripping.
48 * Possible values '1' for enable , '0' for disable.
49 * Default is '2' - which means disable in promisc mode
50 * and enable in non-promiscuous mode.
51 * multiq: This parameter used to enable/disable MULTIQUEUE support.
52 * Possible values '1' for enable and '0' for disable. Default is '0'
53 ************************************************************************/
55 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
57 #include <linux/module.h>
58 #include <linux/types.h>
59 #include <linux/errno.h>
60 #include <linux/ioport.h>
61 #include <linux/pci.h>
62 #include <linux/dma-mapping.h>
63 #include <linux/kernel.h>
64 #include <linux/netdevice.h>
65 #include <linux/etherdevice.h>
66 #include <linux/mdio.h>
67 #include <linux/skbuff.h>
68 #include <linux/init.h>
69 #include <linux/delay.h>
70 #include <linux/stddef.h>
71 #include <linux/ioctl.h>
72 #include <linux/timex.h>
73 #include <linux/ethtool.h>
74 #include <linux/workqueue.h>
75 #include <linux/if_vlan.h>
77 #include <linux/tcp.h>
78 #include <linux/uaccess.h>
80 #include <linux/slab.h>
81 #include <linux/prefetch.h>
83 #include <net/checksum.h>
85 #include <asm/div64.h>
90 #include "s2io-regs.h"
92 #define DRV_VERSION "2.0.26.28"
94 /* S2io Driver name & version. */
95 static const char s2io_driver_name[] = "Neterion";
96 static const char s2io_driver_version[] = DRV_VERSION;
98 static const int rxd_size[2] = {32, 48};
99 static const int rxd_count[2] = {127, 85};
101 static inline int RXD_IS_UP2DT(struct RxD_t *rxdp)
105 ret = ((!(rxdp->Control_1 & RXD_OWN_XENA)) &&
106 (GET_RXD_MARKER(rxdp->Control_2) != THE_RXD_MARK));
112 * Cards with following subsystem_id have a link state indication
113 * problem, 600B, 600C, 600D, 640B, 640C and 640D.
114 * macro below identifies these cards given the subsystem_id.
116 #define CARDS_WITH_FAULTY_LINK_INDICATORS(dev_type, subid) \
117 (dev_type == XFRAME_I_DEVICE) ? \
118 ((((subid >= 0x600B) && (subid <= 0x600D)) || \
119 ((subid >= 0x640B) && (subid <= 0x640D))) ? 1 : 0) : 0
121 #define LINK_IS_UP(val64) (!(val64 & (ADAPTER_STATUS_RMAC_REMOTE_FAULT | \
122 ADAPTER_STATUS_RMAC_LOCAL_FAULT)))
124 static inline int is_s2io_card_up(const struct s2io_nic *sp)
126 return test_bit(__S2IO_STATE_CARD_UP, &sp->state);
129 /* Ethtool related variables and Macros. */
130 static const char s2io_gstrings[][ETH_GSTRING_LEN] = {
131 "Register test\t(offline)",
132 "Eeprom test\t(offline)",
133 "Link test\t(online)",
134 "RLDRAM test\t(offline)",
135 "BIST Test\t(offline)"
138 static const char ethtool_xena_stats_keys[][ETH_GSTRING_LEN] = {
140 {"tmac_data_octets"},
144 {"tmac_pause_ctrl_frms"},
148 {"tmac_any_err_frms"},
149 {"tmac_ttl_less_fb_octets"},
150 {"tmac_vld_ip_octets"},
158 {"rmac_data_octets"},
159 {"rmac_fcs_err_frms"},
161 {"rmac_vld_mcst_frms"},
162 {"rmac_vld_bcst_frms"},
163 {"rmac_in_rng_len_err_frms"},
164 {"rmac_out_rng_len_err_frms"},
166 {"rmac_pause_ctrl_frms"},
167 {"rmac_unsup_ctrl_frms"},
169 {"rmac_accepted_ucst_frms"},
170 {"rmac_accepted_nucst_frms"},
171 {"rmac_discarded_frms"},
172 {"rmac_drop_events"},
173 {"rmac_ttl_less_fb_octets"},
175 {"rmac_usized_frms"},
176 {"rmac_osized_frms"},
178 {"rmac_jabber_frms"},
179 {"rmac_ttl_64_frms"},
180 {"rmac_ttl_65_127_frms"},
181 {"rmac_ttl_128_255_frms"},
182 {"rmac_ttl_256_511_frms"},
183 {"rmac_ttl_512_1023_frms"},
184 {"rmac_ttl_1024_1518_frms"},
192 {"rmac_err_drp_udp"},
193 {"rmac_xgmii_err_sym"},
211 {"rmac_xgmii_data_err_cnt"},
212 {"rmac_xgmii_ctrl_err_cnt"},
213 {"rmac_accepted_ip"},
217 {"new_rd_req_rtry_cnt"},
219 {"wr_rtry_rd_ack_cnt"},
222 {"new_wr_req_rtry_cnt"},
225 {"rd_rtry_wr_ack_cnt"},
235 static const char ethtool_enhanced_stats_keys[][ETH_GSTRING_LEN] = {
236 {"rmac_ttl_1519_4095_frms"},
237 {"rmac_ttl_4096_8191_frms"},
238 {"rmac_ttl_8192_max_frms"},
239 {"rmac_ttl_gt_max_frms"},
240 {"rmac_osized_alt_frms"},
241 {"rmac_jabber_alt_frms"},
242 {"rmac_gt_max_alt_frms"},
244 {"rmac_len_discard"},
245 {"rmac_fcs_discard"},
248 {"rmac_red_discard"},
249 {"rmac_rts_discard"},
250 {"rmac_ingm_full_discard"},
254 static const char ethtool_driver_stats_keys[][ETH_GSTRING_LEN] = {
255 {"\n DRIVER STATISTICS"},
256 {"single_bit_ecc_errs"},
257 {"double_bit_ecc_errs"},
270 {"alarm_transceiver_temp_high"},
271 {"alarm_transceiver_temp_low"},
272 {"alarm_laser_bias_current_high"},
273 {"alarm_laser_bias_current_low"},
274 {"alarm_laser_output_power_high"},
275 {"alarm_laser_output_power_low"},
276 {"warn_transceiver_temp_high"},
277 {"warn_transceiver_temp_low"},
278 {"warn_laser_bias_current_high"},
279 {"warn_laser_bias_current_low"},
280 {"warn_laser_output_power_high"},
281 {"warn_laser_output_power_low"},
282 {"lro_aggregated_pkts"},
283 {"lro_flush_both_count"},
284 {"lro_out_of_sequence_pkts"},
285 {"lro_flush_due_to_max_pkts"},
286 {"lro_avg_aggr_pkts"},
287 {"mem_alloc_fail_cnt"},
288 {"pci_map_fail_cnt"},
289 {"watchdog_timer_cnt"},
296 {"tx_tcode_buf_abort_cnt"},
297 {"tx_tcode_desc_abort_cnt"},
298 {"tx_tcode_parity_err_cnt"},
299 {"tx_tcode_link_loss_cnt"},
300 {"tx_tcode_list_proc_err_cnt"},
301 {"rx_tcode_parity_err_cnt"},
302 {"rx_tcode_abort_cnt"},
303 {"rx_tcode_parity_abort_cnt"},
304 {"rx_tcode_rda_fail_cnt"},
305 {"rx_tcode_unkn_prot_cnt"},
306 {"rx_tcode_fcs_err_cnt"},
307 {"rx_tcode_buf_size_err_cnt"},
308 {"rx_tcode_rxd_corrupt_cnt"},
309 {"rx_tcode_unkn_err_cnt"},
317 {"mac_tmac_err_cnt"},
318 {"mac_rmac_err_cnt"},
319 {"xgxs_txgxs_err_cnt"},
320 {"xgxs_rxgxs_err_cnt"},
322 {"prc_pcix_err_cnt"},
329 #define S2IO_XENA_STAT_LEN ARRAY_SIZE(ethtool_xena_stats_keys)
330 #define S2IO_ENHANCED_STAT_LEN ARRAY_SIZE(ethtool_enhanced_stats_keys)
331 #define S2IO_DRIVER_STAT_LEN ARRAY_SIZE(ethtool_driver_stats_keys)
333 #define XFRAME_I_STAT_LEN (S2IO_XENA_STAT_LEN + S2IO_DRIVER_STAT_LEN)
334 #define XFRAME_II_STAT_LEN (XFRAME_I_STAT_LEN + S2IO_ENHANCED_STAT_LEN)
336 #define XFRAME_I_STAT_STRINGS_LEN (XFRAME_I_STAT_LEN * ETH_GSTRING_LEN)
337 #define XFRAME_II_STAT_STRINGS_LEN (XFRAME_II_STAT_LEN * ETH_GSTRING_LEN)
339 #define S2IO_TEST_LEN ARRAY_SIZE(s2io_gstrings)
340 #define S2IO_STRINGS_LEN (S2IO_TEST_LEN * ETH_GSTRING_LEN)
342 #define S2IO_TIMER_CONF(timer, handle, arg, exp) \
343 init_timer(&timer); \
344 timer.function = handle; \
345 timer.data = (unsigned long)arg; \
346 mod_timer(&timer, (jiffies + exp)) \
348 /* copy mac addr to def_mac_addr array */
349 static void do_s2io_copy_mac_addr(struct s2io_nic *sp, int offset, u64 mac_addr)
351 sp->def_mac_addr[offset].mac_addr[5] = (u8) (mac_addr);
352 sp->def_mac_addr[offset].mac_addr[4] = (u8) (mac_addr >> 8);
353 sp->def_mac_addr[offset].mac_addr[3] = (u8) (mac_addr >> 16);
354 sp->def_mac_addr[offset].mac_addr[2] = (u8) (mac_addr >> 24);
355 sp->def_mac_addr[offset].mac_addr[1] = (u8) (mac_addr >> 32);
356 sp->def_mac_addr[offset].mac_addr[0] = (u8) (mac_addr >> 40);
360 * Constants to be programmed into the Xena's registers, to configure
365 static const u64 herc_act_dtx_cfg[] = {
367 0x8000051536750000ULL, 0x80000515367500E0ULL,
369 0x8000051536750004ULL, 0x80000515367500E4ULL,
371 0x80010515003F0000ULL, 0x80010515003F00E0ULL,
373 0x80010515003F0004ULL, 0x80010515003F00E4ULL,
375 0x801205150D440000ULL, 0x801205150D4400E0ULL,
377 0x801205150D440004ULL, 0x801205150D4400E4ULL,
379 0x80020515F2100000ULL, 0x80020515F21000E0ULL,
381 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
386 static const u64 xena_dtx_cfg[] = {
388 0x8000051500000000ULL, 0x80000515000000E0ULL,
390 0x80000515D9350004ULL, 0x80000515D93500E4ULL,
392 0x8001051500000000ULL, 0x80010515000000E0ULL,
394 0x80010515001E0004ULL, 0x80010515001E00E4ULL,
396 0x8002051500000000ULL, 0x80020515000000E0ULL,
398 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
403 * Constants for Fixing the MacAddress problem seen mostly on
406 static const u64 fix_mac[] = {
407 0x0060000000000000ULL, 0x0060600000000000ULL,
408 0x0040600000000000ULL, 0x0000600000000000ULL,
409 0x0020600000000000ULL, 0x0060600000000000ULL,
410 0x0020600000000000ULL, 0x0060600000000000ULL,
411 0x0020600000000000ULL, 0x0060600000000000ULL,
412 0x0020600000000000ULL, 0x0060600000000000ULL,
413 0x0020600000000000ULL, 0x0060600000000000ULL,
414 0x0020600000000000ULL, 0x0060600000000000ULL,
415 0x0020600000000000ULL, 0x0060600000000000ULL,
416 0x0020600000000000ULL, 0x0060600000000000ULL,
417 0x0020600000000000ULL, 0x0060600000000000ULL,
418 0x0020600000000000ULL, 0x0060600000000000ULL,
419 0x0020600000000000ULL, 0x0000600000000000ULL,
420 0x0040600000000000ULL, 0x0060600000000000ULL,
424 MODULE_LICENSE("GPL");
425 MODULE_VERSION(DRV_VERSION);
428 /* Module Loadable parameters. */
429 S2IO_PARM_INT(tx_fifo_num, FIFO_DEFAULT_NUM);
430 S2IO_PARM_INT(rx_ring_num, 1);
431 S2IO_PARM_INT(multiq, 0);
432 S2IO_PARM_INT(rx_ring_mode, 1);
433 S2IO_PARM_INT(use_continuous_tx_intrs, 1);
434 S2IO_PARM_INT(rmac_pause_time, 0x100);
435 S2IO_PARM_INT(mc_pause_threshold_q0q3, 187);
436 S2IO_PARM_INT(mc_pause_threshold_q4q7, 187);
437 S2IO_PARM_INT(shared_splits, 0);
438 S2IO_PARM_INT(tmac_util_period, 5);
439 S2IO_PARM_INT(rmac_util_period, 5);
440 S2IO_PARM_INT(l3l4hdr_size, 128);
441 /* 0 is no steering, 1 is Priority steering, 2 is Default steering */
442 S2IO_PARM_INT(tx_steering_type, TX_DEFAULT_STEERING);
443 /* Frequency of Rx desc syncs expressed as power of 2 */
444 S2IO_PARM_INT(rxsync_frequency, 3);
445 /* Interrupt type. Values can be 0(INTA), 2(MSI_X) */
446 S2IO_PARM_INT(intr_type, 2);
447 /* Large receive offload feature */
449 /* Max pkts to be aggregated by LRO at one time. If not specified,
450 * aggregation happens until we hit max IP pkt size(64K)
452 S2IO_PARM_INT(lro_max_pkts, 0xFFFF);
453 S2IO_PARM_INT(indicate_max_pkts, 0);
455 S2IO_PARM_INT(napi, 1);
456 S2IO_PARM_INT(ufo, 0);
457 S2IO_PARM_INT(vlan_tag_strip, NO_STRIP_IN_PROMISC);
459 static unsigned int tx_fifo_len[MAX_TX_FIFOS] =
460 {DEFAULT_FIFO_0_LEN, [1 ...(MAX_TX_FIFOS - 1)] = DEFAULT_FIFO_1_7_LEN};
461 static unsigned int rx_ring_sz[MAX_RX_RINGS] =
462 {[0 ...(MAX_RX_RINGS - 1)] = SMALL_BLK_CNT};
463 static unsigned int rts_frm_len[MAX_RX_RINGS] =
464 {[0 ...(MAX_RX_RINGS - 1)] = 0 };
466 module_param_array(tx_fifo_len, uint, NULL, 0);
467 module_param_array(rx_ring_sz, uint, NULL, 0);
468 module_param_array(rts_frm_len, uint, NULL, 0);
472 * This table lists all the devices that this driver supports.
474 static const struct pci_device_id s2io_tbl[] = {
475 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_WIN,
476 PCI_ANY_ID, PCI_ANY_ID},
477 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_UNI,
478 PCI_ANY_ID, PCI_ANY_ID},
479 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_WIN,
480 PCI_ANY_ID, PCI_ANY_ID},
481 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_UNI,
482 PCI_ANY_ID, PCI_ANY_ID},
486 MODULE_DEVICE_TABLE(pci, s2io_tbl);
488 static const struct pci_error_handlers s2io_err_handler = {
489 .error_detected = s2io_io_error_detected,
490 .slot_reset = s2io_io_slot_reset,
491 .resume = s2io_io_resume,
494 static struct pci_driver s2io_driver = {
496 .id_table = s2io_tbl,
497 .probe = s2io_init_nic,
498 .remove = s2io_rem_nic,
499 .err_handler = &s2io_err_handler,
502 /* A simplifier macro used both by init and free shared_mem Fns(). */
503 #define TXD_MEM_PAGE_CNT(len, per_each) ((len+per_each - 1) / per_each)
505 /* netqueue manipulation helper functions */
506 static inline void s2io_stop_all_tx_queue(struct s2io_nic *sp)
508 if (!sp->config.multiq) {
511 for (i = 0; i < sp->config.tx_fifo_num; i++)
512 sp->mac_control.fifos[i].queue_state = FIFO_QUEUE_STOP;
514 netif_tx_stop_all_queues(sp->dev);
517 static inline void s2io_stop_tx_queue(struct s2io_nic *sp, int fifo_no)
519 if (!sp->config.multiq)
520 sp->mac_control.fifos[fifo_no].queue_state =
523 netif_tx_stop_all_queues(sp->dev);
526 static inline void s2io_start_all_tx_queue(struct s2io_nic *sp)
528 if (!sp->config.multiq) {
531 for (i = 0; i < sp->config.tx_fifo_num; i++)
532 sp->mac_control.fifos[i].queue_state = FIFO_QUEUE_START;
534 netif_tx_start_all_queues(sp->dev);
537 static inline void s2io_wake_all_tx_queue(struct s2io_nic *sp)
539 if (!sp->config.multiq) {
542 for (i = 0; i < sp->config.tx_fifo_num; i++)
543 sp->mac_control.fifos[i].queue_state = FIFO_QUEUE_START;
545 netif_tx_wake_all_queues(sp->dev);
548 static inline void s2io_wake_tx_queue(
549 struct fifo_info *fifo, int cnt, u8 multiq)
553 if (cnt && __netif_subqueue_stopped(fifo->dev, fifo->fifo_no))
554 netif_wake_subqueue(fifo->dev, fifo->fifo_no);
555 } else if (cnt && (fifo->queue_state == FIFO_QUEUE_STOP)) {
556 if (netif_queue_stopped(fifo->dev)) {
557 fifo->queue_state = FIFO_QUEUE_START;
558 netif_wake_queue(fifo->dev);
564 * init_shared_mem - Allocation and Initialization of Memory
565 * @nic: Device private variable.
566 * Description: The function allocates all the memory areas shared
567 * between the NIC and the driver. This includes Tx descriptors,
568 * Rx descriptors and the statistics block.
571 static int init_shared_mem(struct s2io_nic *nic)
574 void *tmp_v_addr, *tmp_v_addr_next;
575 dma_addr_t tmp_p_addr, tmp_p_addr_next;
576 struct RxD_block *pre_rxd_blk = NULL;
578 int lst_size, lst_per_page;
579 struct net_device *dev = nic->dev;
582 struct config_param *config = &nic->config;
583 struct mac_info *mac_control = &nic->mac_control;
584 unsigned long long mem_allocated = 0;
586 /* Allocation and initialization of TXDLs in FIFOs */
588 for (i = 0; i < config->tx_fifo_num; i++) {
589 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
591 size += tx_cfg->fifo_len;
593 if (size > MAX_AVAILABLE_TXDS) {
595 "Too many TxDs requested: %d, max supported: %d\n",
596 size, MAX_AVAILABLE_TXDS);
601 for (i = 0; i < config->tx_fifo_num; i++) {
602 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
604 size = tx_cfg->fifo_len;
606 * Legal values are from 2 to 8192
609 DBG_PRINT(ERR_DBG, "Fifo %d: Invalid length (%d) - "
610 "Valid lengths are 2 through 8192\n",
616 lst_size = (sizeof(struct TxD) * config->max_txds);
617 lst_per_page = PAGE_SIZE / lst_size;
619 for (i = 0; i < config->tx_fifo_num; i++) {
620 struct fifo_info *fifo = &mac_control->fifos[i];
621 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
622 int fifo_len = tx_cfg->fifo_len;
623 int list_holder_size = fifo_len * sizeof(struct list_info_hold);
625 fifo->list_info = kzalloc(list_holder_size, GFP_KERNEL);
626 if (!fifo->list_info) {
627 DBG_PRINT(INFO_DBG, "Malloc failed for list_info\n");
630 mem_allocated += list_holder_size;
632 for (i = 0; i < config->tx_fifo_num; i++) {
633 int page_num = TXD_MEM_PAGE_CNT(config->tx_cfg[i].fifo_len,
635 struct fifo_info *fifo = &mac_control->fifos[i];
636 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
638 fifo->tx_curr_put_info.offset = 0;
639 fifo->tx_curr_put_info.fifo_len = tx_cfg->fifo_len - 1;
640 fifo->tx_curr_get_info.offset = 0;
641 fifo->tx_curr_get_info.fifo_len = tx_cfg->fifo_len - 1;
644 fifo->max_txds = MAX_SKB_FRAGS + 2;
647 for (j = 0; j < page_num; j++) {
651 tmp_v = pci_alloc_consistent(nic->pdev,
655 "pci_alloc_consistent failed for TxDL\n");
658 /* If we got a zero DMA address(can happen on
659 * certain platforms like PPC), reallocate.
660 * Store virtual address of page we don't want,
664 mac_control->zerodma_virt_addr = tmp_v;
666 "%s: Zero DMA address for TxDL. "
667 "Virtual address %p\n",
669 tmp_v = pci_alloc_consistent(nic->pdev,
673 "pci_alloc_consistent failed for TxDL\n");
676 mem_allocated += PAGE_SIZE;
678 while (k < lst_per_page) {
679 int l = (j * lst_per_page) + k;
680 if (l == tx_cfg->fifo_len)
682 fifo->list_info[l].list_virt_addr =
683 tmp_v + (k * lst_size);
684 fifo->list_info[l].list_phy_addr =
685 tmp_p + (k * lst_size);
691 for (i = 0; i < config->tx_fifo_num; i++) {
692 struct fifo_info *fifo = &mac_control->fifos[i];
693 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
695 size = tx_cfg->fifo_len;
696 fifo->ufo_in_band_v = kcalloc(size, sizeof(u64), GFP_KERNEL);
697 if (!fifo->ufo_in_band_v)
699 mem_allocated += (size * sizeof(u64));
702 /* Allocation and initialization of RXDs in Rings */
704 for (i = 0; i < config->rx_ring_num; i++) {
705 struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
706 struct ring_info *ring = &mac_control->rings[i];
708 if (rx_cfg->num_rxd % (rxd_count[nic->rxd_mode] + 1)) {
709 DBG_PRINT(ERR_DBG, "%s: Ring%d RxD count is not a "
710 "multiple of RxDs per Block\n",
714 size += rx_cfg->num_rxd;
715 ring->block_count = rx_cfg->num_rxd /
716 (rxd_count[nic->rxd_mode] + 1);
717 ring->pkt_cnt = rx_cfg->num_rxd - ring->block_count;
719 if (nic->rxd_mode == RXD_MODE_1)
720 size = (size * (sizeof(struct RxD1)));
722 size = (size * (sizeof(struct RxD3)));
724 for (i = 0; i < config->rx_ring_num; i++) {
725 struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
726 struct ring_info *ring = &mac_control->rings[i];
728 ring->rx_curr_get_info.block_index = 0;
729 ring->rx_curr_get_info.offset = 0;
730 ring->rx_curr_get_info.ring_len = rx_cfg->num_rxd - 1;
731 ring->rx_curr_put_info.block_index = 0;
732 ring->rx_curr_put_info.offset = 0;
733 ring->rx_curr_put_info.ring_len = rx_cfg->num_rxd - 1;
737 blk_cnt = rx_cfg->num_rxd / (rxd_count[nic->rxd_mode] + 1);
738 /* Allocating all the Rx blocks */
739 for (j = 0; j < blk_cnt; j++) {
740 struct rx_block_info *rx_blocks;
743 rx_blocks = &ring->rx_blocks[j];
744 size = SIZE_OF_BLOCK; /* size is always page size */
745 tmp_v_addr = pci_alloc_consistent(nic->pdev, size,
747 if (tmp_v_addr == NULL) {
749 * In case of failure, free_shared_mem()
750 * is called, which should free any
751 * memory that was alloced till the
754 rx_blocks->block_virt_addr = tmp_v_addr;
757 mem_allocated += size;
758 memset(tmp_v_addr, 0, size);
760 size = sizeof(struct rxd_info) *
761 rxd_count[nic->rxd_mode];
762 rx_blocks->block_virt_addr = tmp_v_addr;
763 rx_blocks->block_dma_addr = tmp_p_addr;
764 rx_blocks->rxds = kmalloc(size, GFP_KERNEL);
765 if (!rx_blocks->rxds)
767 mem_allocated += size;
768 for (l = 0; l < rxd_count[nic->rxd_mode]; l++) {
769 rx_blocks->rxds[l].virt_addr =
770 rx_blocks->block_virt_addr +
771 (rxd_size[nic->rxd_mode] * l);
772 rx_blocks->rxds[l].dma_addr =
773 rx_blocks->block_dma_addr +
774 (rxd_size[nic->rxd_mode] * l);
777 /* Interlinking all Rx Blocks */
778 for (j = 0; j < blk_cnt; j++) {
779 int next = (j + 1) % blk_cnt;
780 tmp_v_addr = ring->rx_blocks[j].block_virt_addr;
781 tmp_v_addr_next = ring->rx_blocks[next].block_virt_addr;
782 tmp_p_addr = ring->rx_blocks[j].block_dma_addr;
783 tmp_p_addr_next = ring->rx_blocks[next].block_dma_addr;
785 pre_rxd_blk = tmp_v_addr;
786 pre_rxd_blk->reserved_2_pNext_RxD_block =
787 (unsigned long)tmp_v_addr_next;
788 pre_rxd_blk->pNext_RxD_Blk_physical =
789 (u64)tmp_p_addr_next;
792 if (nic->rxd_mode == RXD_MODE_3B) {
794 * Allocation of Storages for buffer addresses in 2BUFF mode
795 * and the buffers as well.
797 for (i = 0; i < config->rx_ring_num; i++) {
798 struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
799 struct ring_info *ring = &mac_control->rings[i];
801 blk_cnt = rx_cfg->num_rxd /
802 (rxd_count[nic->rxd_mode] + 1);
803 size = sizeof(struct buffAdd *) * blk_cnt;
804 ring->ba = kmalloc(size, GFP_KERNEL);
807 mem_allocated += size;
808 for (j = 0; j < blk_cnt; j++) {
811 size = sizeof(struct buffAdd) *
812 (rxd_count[nic->rxd_mode] + 1);
813 ring->ba[j] = kmalloc(size, GFP_KERNEL);
816 mem_allocated += size;
817 while (k != rxd_count[nic->rxd_mode]) {
818 ba = &ring->ba[j][k];
819 size = BUF0_LEN + ALIGN_SIZE;
820 ba->ba_0_org = kmalloc(size, GFP_KERNEL);
823 mem_allocated += size;
824 tmp = (unsigned long)ba->ba_0_org;
826 tmp &= ~((unsigned long)ALIGN_SIZE);
827 ba->ba_0 = (void *)tmp;
829 size = BUF1_LEN + ALIGN_SIZE;
830 ba->ba_1_org = kmalloc(size, GFP_KERNEL);
833 mem_allocated += size;
834 tmp = (unsigned long)ba->ba_1_org;
836 tmp &= ~((unsigned long)ALIGN_SIZE);
837 ba->ba_1 = (void *)tmp;
844 /* Allocation and initialization of Statistics block */
845 size = sizeof(struct stat_block);
846 mac_control->stats_mem =
847 pci_alloc_consistent(nic->pdev, size,
848 &mac_control->stats_mem_phy);
850 if (!mac_control->stats_mem) {
852 * In case of failure, free_shared_mem() is called, which
853 * should free any memory that was alloced till the
858 mem_allocated += size;
859 mac_control->stats_mem_sz = size;
861 tmp_v_addr = mac_control->stats_mem;
862 mac_control->stats_info = tmp_v_addr;
863 memset(tmp_v_addr, 0, size);
864 DBG_PRINT(INIT_DBG, "%s: Ring Mem PHY: 0x%llx\n",
865 dev_name(&nic->pdev->dev), (unsigned long long)tmp_p_addr);
866 mac_control->stats_info->sw_stat.mem_allocated += mem_allocated;
871 * free_shared_mem - Free the allocated Memory
872 * @nic: Device private variable.
873 * Description: This function is to free all memory locations allocated by
874 * the init_shared_mem() function and return it to the kernel.
877 static void free_shared_mem(struct s2io_nic *nic)
879 int i, j, blk_cnt, size;
881 dma_addr_t tmp_p_addr;
882 int lst_size, lst_per_page;
883 struct net_device *dev;
885 struct config_param *config;
886 struct mac_info *mac_control;
887 struct stat_block *stats;
888 struct swStat *swstats;
895 config = &nic->config;
896 mac_control = &nic->mac_control;
897 stats = mac_control->stats_info;
898 swstats = &stats->sw_stat;
900 lst_size = sizeof(struct TxD) * config->max_txds;
901 lst_per_page = PAGE_SIZE / lst_size;
903 for (i = 0; i < config->tx_fifo_num; i++) {
904 struct fifo_info *fifo = &mac_control->fifos[i];
905 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
907 page_num = TXD_MEM_PAGE_CNT(tx_cfg->fifo_len, lst_per_page);
908 for (j = 0; j < page_num; j++) {
909 int mem_blks = (j * lst_per_page);
910 struct list_info_hold *fli;
912 if (!fifo->list_info)
915 fli = &fifo->list_info[mem_blks];
916 if (!fli->list_virt_addr)
918 pci_free_consistent(nic->pdev, PAGE_SIZE,
921 swstats->mem_freed += PAGE_SIZE;
923 /* If we got a zero DMA address during allocation,
926 if (mac_control->zerodma_virt_addr) {
927 pci_free_consistent(nic->pdev, PAGE_SIZE,
928 mac_control->zerodma_virt_addr,
931 "%s: Freeing TxDL with zero DMA address. "
932 "Virtual address %p\n",
933 dev->name, mac_control->zerodma_virt_addr);
934 swstats->mem_freed += PAGE_SIZE;
936 kfree(fifo->list_info);
937 swstats->mem_freed += tx_cfg->fifo_len *
938 sizeof(struct list_info_hold);
941 size = SIZE_OF_BLOCK;
942 for (i = 0; i < config->rx_ring_num; i++) {
943 struct ring_info *ring = &mac_control->rings[i];
945 blk_cnt = ring->block_count;
946 for (j = 0; j < blk_cnt; j++) {
947 tmp_v_addr = ring->rx_blocks[j].block_virt_addr;
948 tmp_p_addr = ring->rx_blocks[j].block_dma_addr;
949 if (tmp_v_addr == NULL)
951 pci_free_consistent(nic->pdev, size,
952 tmp_v_addr, tmp_p_addr);
953 swstats->mem_freed += size;
954 kfree(ring->rx_blocks[j].rxds);
955 swstats->mem_freed += sizeof(struct rxd_info) *
956 rxd_count[nic->rxd_mode];
960 if (nic->rxd_mode == RXD_MODE_3B) {
961 /* Freeing buffer storage addresses in 2BUFF mode. */
962 for (i = 0; i < config->rx_ring_num; i++) {
963 struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
964 struct ring_info *ring = &mac_control->rings[i];
966 blk_cnt = rx_cfg->num_rxd /
967 (rxd_count[nic->rxd_mode] + 1);
968 for (j = 0; j < blk_cnt; j++) {
972 while (k != rxd_count[nic->rxd_mode]) {
973 struct buffAdd *ba = &ring->ba[j][k];
975 swstats->mem_freed +=
976 BUF0_LEN + ALIGN_SIZE;
978 swstats->mem_freed +=
979 BUF1_LEN + ALIGN_SIZE;
983 swstats->mem_freed += sizeof(struct buffAdd) *
984 (rxd_count[nic->rxd_mode] + 1);
987 swstats->mem_freed += sizeof(struct buffAdd *) *
992 for (i = 0; i < nic->config.tx_fifo_num; i++) {
993 struct fifo_info *fifo = &mac_control->fifos[i];
994 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
996 if (fifo->ufo_in_band_v) {
997 swstats->mem_freed += tx_cfg->fifo_len *
999 kfree(fifo->ufo_in_band_v);
1003 if (mac_control->stats_mem) {
1004 swstats->mem_freed += mac_control->stats_mem_sz;
1005 pci_free_consistent(nic->pdev,
1006 mac_control->stats_mem_sz,
1007 mac_control->stats_mem,
1008 mac_control->stats_mem_phy);
1013 * s2io_verify_pci_mode -
1016 static int s2io_verify_pci_mode(struct s2io_nic *nic)
1018 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1019 register u64 val64 = 0;
1022 val64 = readq(&bar0->pci_mode);
1023 mode = (u8)GET_PCI_MODE(val64);
1025 if (val64 & PCI_MODE_UNKNOWN_MODE)
1026 return -1; /* Unknown PCI mode */
1030 #define NEC_VENID 0x1033
1031 #define NEC_DEVID 0x0125
1032 static int s2io_on_nec_bridge(struct pci_dev *s2io_pdev)
1034 struct pci_dev *tdev = NULL;
1035 for_each_pci_dev(tdev) {
1036 if (tdev->vendor == NEC_VENID && tdev->device == NEC_DEVID) {
1037 if (tdev->bus == s2io_pdev->bus->parent) {
1046 static int bus_speed[8] = {33, 133, 133, 200, 266, 133, 200, 266};
1048 * s2io_print_pci_mode -
1050 static int s2io_print_pci_mode(struct s2io_nic *nic)
1052 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1053 register u64 val64 = 0;
1055 struct config_param *config = &nic->config;
1056 const char *pcimode;
1058 val64 = readq(&bar0->pci_mode);
1059 mode = (u8)GET_PCI_MODE(val64);
1061 if (val64 & PCI_MODE_UNKNOWN_MODE)
1062 return -1; /* Unknown PCI mode */
1064 config->bus_speed = bus_speed[mode];
1066 if (s2io_on_nec_bridge(nic->pdev)) {
1067 DBG_PRINT(ERR_DBG, "%s: Device is on PCI-E bus\n",
1073 case PCI_MODE_PCI_33:
1074 pcimode = "33MHz PCI bus";
1076 case PCI_MODE_PCI_66:
1077 pcimode = "66MHz PCI bus";
1079 case PCI_MODE_PCIX_M1_66:
1080 pcimode = "66MHz PCIX(M1) bus";
1082 case PCI_MODE_PCIX_M1_100:
1083 pcimode = "100MHz PCIX(M1) bus";
1085 case PCI_MODE_PCIX_M1_133:
1086 pcimode = "133MHz PCIX(M1) bus";
1088 case PCI_MODE_PCIX_M2_66:
1089 pcimode = "133MHz PCIX(M2) bus";
1091 case PCI_MODE_PCIX_M2_100:
1092 pcimode = "200MHz PCIX(M2) bus";
1094 case PCI_MODE_PCIX_M2_133:
1095 pcimode = "266MHz PCIX(M2) bus";
1098 pcimode = "unsupported bus!";
1102 DBG_PRINT(ERR_DBG, "%s: Device is on %d bit %s\n",
1103 nic->dev->name, val64 & PCI_MODE_32_BITS ? 32 : 64, pcimode);
1109 * init_tti - Initialization transmit traffic interrupt scheme
1110 * @nic: device private variable
1111 * @link: link status (UP/DOWN) used to enable/disable continuous
1112 * transmit interrupts
1113 * Description: The function configures transmit traffic interrupts
1114 * Return Value: SUCCESS on success and
1118 static int init_tti(struct s2io_nic *nic, int link)
1120 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1121 register u64 val64 = 0;
1123 struct config_param *config = &nic->config;
1125 for (i = 0; i < config->tx_fifo_num; i++) {
1127 * TTI Initialization. Default Tx timer gets us about
1128 * 250 interrupts per sec. Continuous interrupts are enabled
1131 if (nic->device_type == XFRAME_II_DEVICE) {
1132 int count = (nic->config.bus_speed * 125)/2;
1133 val64 = TTI_DATA1_MEM_TX_TIMER_VAL(count);
1135 val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078);
1137 val64 |= TTI_DATA1_MEM_TX_URNG_A(0xA) |
1138 TTI_DATA1_MEM_TX_URNG_B(0x10) |
1139 TTI_DATA1_MEM_TX_URNG_C(0x30) |
1140 TTI_DATA1_MEM_TX_TIMER_AC_EN;
1142 if (use_continuous_tx_intrs && (link == LINK_UP))
1143 val64 |= TTI_DATA1_MEM_TX_TIMER_CI_EN;
1144 writeq(val64, &bar0->tti_data1_mem);
1146 if (nic->config.intr_type == MSI_X) {
1147 val64 = TTI_DATA2_MEM_TX_UFC_A(0x10) |
1148 TTI_DATA2_MEM_TX_UFC_B(0x100) |
1149 TTI_DATA2_MEM_TX_UFC_C(0x200) |
1150 TTI_DATA2_MEM_TX_UFC_D(0x300);
1152 if ((nic->config.tx_steering_type ==
1153 TX_DEFAULT_STEERING) &&
1154 (config->tx_fifo_num > 1) &&
1155 (i >= nic->udp_fifo_idx) &&
1156 (i < (nic->udp_fifo_idx +
1157 nic->total_udp_fifos)))
1158 val64 = TTI_DATA2_MEM_TX_UFC_A(0x50) |
1159 TTI_DATA2_MEM_TX_UFC_B(0x80) |
1160 TTI_DATA2_MEM_TX_UFC_C(0x100) |
1161 TTI_DATA2_MEM_TX_UFC_D(0x120);
1163 val64 = TTI_DATA2_MEM_TX_UFC_A(0x10) |
1164 TTI_DATA2_MEM_TX_UFC_B(0x20) |
1165 TTI_DATA2_MEM_TX_UFC_C(0x40) |
1166 TTI_DATA2_MEM_TX_UFC_D(0x80);
1169 writeq(val64, &bar0->tti_data2_mem);
1171 val64 = TTI_CMD_MEM_WE |
1172 TTI_CMD_MEM_STROBE_NEW_CMD |
1173 TTI_CMD_MEM_OFFSET(i);
1174 writeq(val64, &bar0->tti_command_mem);
1176 if (wait_for_cmd_complete(&bar0->tti_command_mem,
1177 TTI_CMD_MEM_STROBE_NEW_CMD,
1178 S2IO_BIT_RESET) != SUCCESS)
1186 * init_nic - Initialization of hardware
1187 * @nic: device private variable
1188 * Description: The function sequentially configures every block
1189 * of the H/W from their reset values.
1190 * Return Value: SUCCESS on success and
1191 * '-1' on failure (endian settings incorrect).
1194 static int init_nic(struct s2io_nic *nic)
1196 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1197 struct net_device *dev = nic->dev;
1198 register u64 val64 = 0;
1203 unsigned long long mem_share;
1205 struct config_param *config = &nic->config;
1206 struct mac_info *mac_control = &nic->mac_control;
1208 /* to set the swapper controle on the card */
1209 if (s2io_set_swapper(nic)) {
1210 DBG_PRINT(ERR_DBG, "ERROR: Setting Swapper failed\n");
1215 * Herc requires EOI to be removed from reset before XGXS, so..
1217 if (nic->device_type & XFRAME_II_DEVICE) {
1218 val64 = 0xA500000000ULL;
1219 writeq(val64, &bar0->sw_reset);
1221 val64 = readq(&bar0->sw_reset);
1224 /* Remove XGXS from reset state */
1226 writeq(val64, &bar0->sw_reset);
1228 val64 = readq(&bar0->sw_reset);
1230 /* Ensure that it's safe to access registers by checking
1231 * RIC_RUNNING bit is reset. Check is valid only for XframeII.
1233 if (nic->device_type == XFRAME_II_DEVICE) {
1234 for (i = 0; i < 50; i++) {
1235 val64 = readq(&bar0->adapter_status);
1236 if (!(val64 & ADAPTER_STATUS_RIC_RUNNING))
1244 /* Enable Receiving broadcasts */
1245 add = &bar0->mac_cfg;
1246 val64 = readq(&bar0->mac_cfg);
1247 val64 |= MAC_RMAC_BCAST_ENABLE;
1248 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1249 writel((u32)val64, add);
1250 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1251 writel((u32) (val64 >> 32), (add + 4));
1253 /* Read registers in all blocks */
1254 val64 = readq(&bar0->mac_int_mask);
1255 val64 = readq(&bar0->mc_int_mask);
1256 val64 = readq(&bar0->xgxs_int_mask);
1260 writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
1262 if (nic->device_type & XFRAME_II_DEVICE) {
1263 while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) {
1264 SPECIAL_REG_WRITE(herc_act_dtx_cfg[dtx_cnt],
1265 &bar0->dtx_control, UF);
1267 msleep(1); /* Necessary!! */
1271 while (xena_dtx_cfg[dtx_cnt] != END_SIGN) {
1272 SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
1273 &bar0->dtx_control, UF);
1274 val64 = readq(&bar0->dtx_control);
1279 /* Tx DMA Initialization */
1281 writeq(val64, &bar0->tx_fifo_partition_0);
1282 writeq(val64, &bar0->tx_fifo_partition_1);
1283 writeq(val64, &bar0->tx_fifo_partition_2);
1284 writeq(val64, &bar0->tx_fifo_partition_3);
1286 for (i = 0, j = 0; i < config->tx_fifo_num; i++) {
1287 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
1289 val64 |= vBIT(tx_cfg->fifo_len - 1, ((j * 32) + 19), 13) |
1290 vBIT(tx_cfg->fifo_priority, ((j * 32) + 5), 3);
1292 if (i == (config->tx_fifo_num - 1)) {
1299 writeq(val64, &bar0->tx_fifo_partition_0);
1304 writeq(val64, &bar0->tx_fifo_partition_1);
1309 writeq(val64, &bar0->tx_fifo_partition_2);
1314 writeq(val64, &bar0->tx_fifo_partition_3);
1325 * Disable 4 PCCs for Xena1, 2 and 3 as per H/W bug
1326 * SXE-008 TRANSMIT DMA ARBITRATION ISSUE.
1328 if ((nic->device_type == XFRAME_I_DEVICE) && (nic->pdev->revision < 4))
1329 writeq(PCC_ENABLE_FOUR, &bar0->pcc_enable);
1331 val64 = readq(&bar0->tx_fifo_partition_0);
1332 DBG_PRINT(INIT_DBG, "Fifo partition at: 0x%p is: 0x%llx\n",
1333 &bar0->tx_fifo_partition_0, (unsigned long long)val64);
1336 * Initialization of Tx_PA_CONFIG register to ignore packet
1337 * integrity checking.
1339 val64 = readq(&bar0->tx_pa_cfg);
1340 val64 |= TX_PA_CFG_IGNORE_FRM_ERR |
1341 TX_PA_CFG_IGNORE_SNAP_OUI |
1342 TX_PA_CFG_IGNORE_LLC_CTRL |
1343 TX_PA_CFG_IGNORE_L2_ERR;
1344 writeq(val64, &bar0->tx_pa_cfg);
1346 /* Rx DMA intialization. */
1348 for (i = 0; i < config->rx_ring_num; i++) {
1349 struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
1351 val64 |= vBIT(rx_cfg->ring_priority, (5 + (i * 8)), 3);
1353 writeq(val64, &bar0->rx_queue_priority);
1356 * Allocating equal share of memory to all the
1360 if (nic->device_type & XFRAME_II_DEVICE)
1365 for (i = 0; i < config->rx_ring_num; i++) {
1368 mem_share = (mem_size / config->rx_ring_num +
1369 mem_size % config->rx_ring_num);
1370 val64 |= RX_QUEUE_CFG_Q0_SZ(mem_share);
1373 mem_share = (mem_size / config->rx_ring_num);
1374 val64 |= RX_QUEUE_CFG_Q1_SZ(mem_share);
1377 mem_share = (mem_size / config->rx_ring_num);
1378 val64 |= RX_QUEUE_CFG_Q2_SZ(mem_share);
1381 mem_share = (mem_size / config->rx_ring_num);
1382 val64 |= RX_QUEUE_CFG_Q3_SZ(mem_share);
1385 mem_share = (mem_size / config->rx_ring_num);
1386 val64 |= RX_QUEUE_CFG_Q4_SZ(mem_share);
1389 mem_share = (mem_size / config->rx_ring_num);
1390 val64 |= RX_QUEUE_CFG_Q5_SZ(mem_share);
1393 mem_share = (mem_size / config->rx_ring_num);
1394 val64 |= RX_QUEUE_CFG_Q6_SZ(mem_share);
1397 mem_share = (mem_size / config->rx_ring_num);
1398 val64 |= RX_QUEUE_CFG_Q7_SZ(mem_share);
1402 writeq(val64, &bar0->rx_queue_cfg);
1405 * Filling Tx round robin registers
1406 * as per the number of FIFOs for equal scheduling priority
1408 switch (config->tx_fifo_num) {
1411 writeq(val64, &bar0->tx_w_round_robin_0);
1412 writeq(val64, &bar0->tx_w_round_robin_1);
1413 writeq(val64, &bar0->tx_w_round_robin_2);
1414 writeq(val64, &bar0->tx_w_round_robin_3);
1415 writeq(val64, &bar0->tx_w_round_robin_4);
1418 val64 = 0x0001000100010001ULL;
1419 writeq(val64, &bar0->tx_w_round_robin_0);
1420 writeq(val64, &bar0->tx_w_round_robin_1);
1421 writeq(val64, &bar0->tx_w_round_robin_2);
1422 writeq(val64, &bar0->tx_w_round_robin_3);
1423 val64 = 0x0001000100000000ULL;
1424 writeq(val64, &bar0->tx_w_round_robin_4);
1427 val64 = 0x0001020001020001ULL;
1428 writeq(val64, &bar0->tx_w_round_robin_0);
1429 val64 = 0x0200010200010200ULL;
1430 writeq(val64, &bar0->tx_w_round_robin_1);
1431 val64 = 0x0102000102000102ULL;
1432 writeq(val64, &bar0->tx_w_round_robin_2);
1433 val64 = 0x0001020001020001ULL;
1434 writeq(val64, &bar0->tx_w_round_robin_3);
1435 val64 = 0x0200010200000000ULL;
1436 writeq(val64, &bar0->tx_w_round_robin_4);
1439 val64 = 0x0001020300010203ULL;
1440 writeq(val64, &bar0->tx_w_round_robin_0);
1441 writeq(val64, &bar0->tx_w_round_robin_1);
1442 writeq(val64, &bar0->tx_w_round_robin_2);
1443 writeq(val64, &bar0->tx_w_round_robin_3);
1444 val64 = 0x0001020300000000ULL;
1445 writeq(val64, &bar0->tx_w_round_robin_4);
1448 val64 = 0x0001020304000102ULL;
1449 writeq(val64, &bar0->tx_w_round_robin_0);
1450 val64 = 0x0304000102030400ULL;
1451 writeq(val64, &bar0->tx_w_round_robin_1);
1452 val64 = 0x0102030400010203ULL;
1453 writeq(val64, &bar0->tx_w_round_robin_2);
1454 val64 = 0x0400010203040001ULL;
1455 writeq(val64, &bar0->tx_w_round_robin_3);
1456 val64 = 0x0203040000000000ULL;
1457 writeq(val64, &bar0->tx_w_round_robin_4);
1460 val64 = 0x0001020304050001ULL;
1461 writeq(val64, &bar0->tx_w_round_robin_0);
1462 val64 = 0x0203040500010203ULL;
1463 writeq(val64, &bar0->tx_w_round_robin_1);
1464 val64 = 0x0405000102030405ULL;
1465 writeq(val64, &bar0->tx_w_round_robin_2);
1466 val64 = 0x0001020304050001ULL;
1467 writeq(val64, &bar0->tx_w_round_robin_3);
1468 val64 = 0x0203040500000000ULL;
1469 writeq(val64, &bar0->tx_w_round_robin_4);
1472 val64 = 0x0001020304050600ULL;
1473 writeq(val64, &bar0->tx_w_round_robin_0);
1474 val64 = 0x0102030405060001ULL;
1475 writeq(val64, &bar0->tx_w_round_robin_1);
1476 val64 = 0x0203040506000102ULL;
1477 writeq(val64, &bar0->tx_w_round_robin_2);
1478 val64 = 0x0304050600010203ULL;
1479 writeq(val64, &bar0->tx_w_round_robin_3);
1480 val64 = 0x0405060000000000ULL;
1481 writeq(val64, &bar0->tx_w_round_robin_4);
1484 val64 = 0x0001020304050607ULL;
1485 writeq(val64, &bar0->tx_w_round_robin_0);
1486 writeq(val64, &bar0->tx_w_round_robin_1);
1487 writeq(val64, &bar0->tx_w_round_robin_2);
1488 writeq(val64, &bar0->tx_w_round_robin_3);
1489 val64 = 0x0001020300000000ULL;
1490 writeq(val64, &bar0->tx_w_round_robin_4);
1494 /* Enable all configured Tx FIFO partitions */
1495 val64 = readq(&bar0->tx_fifo_partition_0);
1496 val64 |= (TX_FIFO_PARTITION_EN);
1497 writeq(val64, &bar0->tx_fifo_partition_0);
1499 /* Filling the Rx round robin registers as per the
1500 * number of Rings and steering based on QoS with
1503 switch (config->rx_ring_num) {
1506 writeq(val64, &bar0->rx_w_round_robin_0);
1507 writeq(val64, &bar0->rx_w_round_robin_1);
1508 writeq(val64, &bar0->rx_w_round_robin_2);
1509 writeq(val64, &bar0->rx_w_round_robin_3);
1510 writeq(val64, &bar0->rx_w_round_robin_4);
1512 val64 = 0x8080808080808080ULL;
1513 writeq(val64, &bar0->rts_qos_steering);
1516 val64 = 0x0001000100010001ULL;
1517 writeq(val64, &bar0->rx_w_round_robin_0);
1518 writeq(val64, &bar0->rx_w_round_robin_1);
1519 writeq(val64, &bar0->rx_w_round_robin_2);
1520 writeq(val64, &bar0->rx_w_round_robin_3);
1521 val64 = 0x0001000100000000ULL;
1522 writeq(val64, &bar0->rx_w_round_robin_4);
1524 val64 = 0x8080808040404040ULL;
1525 writeq(val64, &bar0->rts_qos_steering);
1528 val64 = 0x0001020001020001ULL;
1529 writeq(val64, &bar0->rx_w_round_robin_0);
1530 val64 = 0x0200010200010200ULL;
1531 writeq(val64, &bar0->rx_w_round_robin_1);
1532 val64 = 0x0102000102000102ULL;
1533 writeq(val64, &bar0->rx_w_round_robin_2);
1534 val64 = 0x0001020001020001ULL;
1535 writeq(val64, &bar0->rx_w_round_robin_3);
1536 val64 = 0x0200010200000000ULL;
1537 writeq(val64, &bar0->rx_w_round_robin_4);
1539 val64 = 0x8080804040402020ULL;
1540 writeq(val64, &bar0->rts_qos_steering);
1543 val64 = 0x0001020300010203ULL;
1544 writeq(val64, &bar0->rx_w_round_robin_0);
1545 writeq(val64, &bar0->rx_w_round_robin_1);
1546 writeq(val64, &bar0->rx_w_round_robin_2);
1547 writeq(val64, &bar0->rx_w_round_robin_3);
1548 val64 = 0x0001020300000000ULL;
1549 writeq(val64, &bar0->rx_w_round_robin_4);
1551 val64 = 0x8080404020201010ULL;
1552 writeq(val64, &bar0->rts_qos_steering);
1555 val64 = 0x0001020304000102ULL;
1556 writeq(val64, &bar0->rx_w_round_robin_0);
1557 val64 = 0x0304000102030400ULL;
1558 writeq(val64, &bar0->rx_w_round_robin_1);
1559 val64 = 0x0102030400010203ULL;
1560 writeq(val64, &bar0->rx_w_round_robin_2);
1561 val64 = 0x0400010203040001ULL;
1562 writeq(val64, &bar0->rx_w_round_robin_3);
1563 val64 = 0x0203040000000000ULL;
1564 writeq(val64, &bar0->rx_w_round_robin_4);
1566 val64 = 0x8080404020201008ULL;
1567 writeq(val64, &bar0->rts_qos_steering);
1570 val64 = 0x0001020304050001ULL;
1571 writeq(val64, &bar0->rx_w_round_robin_0);
1572 val64 = 0x0203040500010203ULL;
1573 writeq(val64, &bar0->rx_w_round_robin_1);
1574 val64 = 0x0405000102030405ULL;
1575 writeq(val64, &bar0->rx_w_round_robin_2);
1576 val64 = 0x0001020304050001ULL;
1577 writeq(val64, &bar0->rx_w_round_robin_3);
1578 val64 = 0x0203040500000000ULL;
1579 writeq(val64, &bar0->rx_w_round_robin_4);
1581 val64 = 0x8080404020100804ULL;
1582 writeq(val64, &bar0->rts_qos_steering);
1585 val64 = 0x0001020304050600ULL;
1586 writeq(val64, &bar0->rx_w_round_robin_0);
1587 val64 = 0x0102030405060001ULL;
1588 writeq(val64, &bar0->rx_w_round_robin_1);
1589 val64 = 0x0203040506000102ULL;
1590 writeq(val64, &bar0->rx_w_round_robin_2);
1591 val64 = 0x0304050600010203ULL;
1592 writeq(val64, &bar0->rx_w_round_robin_3);
1593 val64 = 0x0405060000000000ULL;
1594 writeq(val64, &bar0->rx_w_round_robin_4);
1596 val64 = 0x8080402010080402ULL;
1597 writeq(val64, &bar0->rts_qos_steering);
1600 val64 = 0x0001020304050607ULL;
1601 writeq(val64, &bar0->rx_w_round_robin_0);
1602 writeq(val64, &bar0->rx_w_round_robin_1);
1603 writeq(val64, &bar0->rx_w_round_robin_2);
1604 writeq(val64, &bar0->rx_w_round_robin_3);
1605 val64 = 0x0001020300000000ULL;
1606 writeq(val64, &bar0->rx_w_round_robin_4);
1608 val64 = 0x8040201008040201ULL;
1609 writeq(val64, &bar0->rts_qos_steering);
1615 for (i = 0; i < 8; i++)
1616 writeq(val64, &bar0->rts_frm_len_n[i]);
1618 /* Set the default rts frame length for the rings configured */
1619 val64 = MAC_RTS_FRM_LEN_SET(dev->mtu+22);
1620 for (i = 0 ; i < config->rx_ring_num ; i++)
1621 writeq(val64, &bar0->rts_frm_len_n[i]);
1623 /* Set the frame length for the configured rings
1624 * desired by the user
1626 for (i = 0; i < config->rx_ring_num; i++) {
1627 /* If rts_frm_len[i] == 0 then it is assumed that user not
1628 * specified frame length steering.
1629 * If the user provides the frame length then program
1630 * the rts_frm_len register for those values or else
1631 * leave it as it is.
1633 if (rts_frm_len[i] != 0) {
1634 writeq(MAC_RTS_FRM_LEN_SET(rts_frm_len[i]),
1635 &bar0->rts_frm_len_n[i]);
1639 /* Disable differentiated services steering logic */
1640 for (i = 0; i < 64; i++) {
1641 if (rts_ds_steer(nic, i, 0) == FAILURE) {
1643 "%s: rts_ds_steer failed on codepoint %d\n",
1649 /* Program statistics memory */
1650 writeq(mac_control->stats_mem_phy, &bar0->stat_addr);
1652 if (nic->device_type == XFRAME_II_DEVICE) {
1653 val64 = STAT_BC(0x320);
1654 writeq(val64, &bar0->stat_byte_cnt);
1658 * Initializing the sampling rate for the device to calculate the
1659 * bandwidth utilization.
1661 val64 = MAC_TX_LINK_UTIL_VAL(tmac_util_period) |
1662 MAC_RX_LINK_UTIL_VAL(rmac_util_period);
1663 writeq(val64, &bar0->mac_link_util);
1666 * Initializing the Transmit and Receive Traffic Interrupt
1670 /* Initialize TTI */
1671 if (SUCCESS != init_tti(nic, nic->last_link_state))
1674 /* RTI Initialization */
1675 if (nic->device_type == XFRAME_II_DEVICE) {
1677 * Programmed to generate Apprx 500 Intrs per
1680 int count = (nic->config.bus_speed * 125)/4;
1681 val64 = RTI_DATA1_MEM_RX_TIMER_VAL(count);
1683 val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF);
1684 val64 |= RTI_DATA1_MEM_RX_URNG_A(0xA) |
1685 RTI_DATA1_MEM_RX_URNG_B(0x10) |
1686 RTI_DATA1_MEM_RX_URNG_C(0x30) |
1687 RTI_DATA1_MEM_RX_TIMER_AC_EN;
1689 writeq(val64, &bar0->rti_data1_mem);
1691 val64 = RTI_DATA2_MEM_RX_UFC_A(0x1) |
1692 RTI_DATA2_MEM_RX_UFC_B(0x2) ;
1693 if (nic->config.intr_type == MSI_X)
1694 val64 |= (RTI_DATA2_MEM_RX_UFC_C(0x20) |
1695 RTI_DATA2_MEM_RX_UFC_D(0x40));
1697 val64 |= (RTI_DATA2_MEM_RX_UFC_C(0x40) |
1698 RTI_DATA2_MEM_RX_UFC_D(0x80));
1699 writeq(val64, &bar0->rti_data2_mem);
1701 for (i = 0; i < config->rx_ring_num; i++) {
1702 val64 = RTI_CMD_MEM_WE |
1703 RTI_CMD_MEM_STROBE_NEW_CMD |
1704 RTI_CMD_MEM_OFFSET(i);
1705 writeq(val64, &bar0->rti_command_mem);
1708 * Once the operation completes, the Strobe bit of the
1709 * command register will be reset. We poll for this
1710 * particular condition. We wait for a maximum of 500ms
1711 * for the operation to complete, if it's not complete
1712 * by then we return error.
1716 val64 = readq(&bar0->rti_command_mem);
1717 if (!(val64 & RTI_CMD_MEM_STROBE_NEW_CMD))
1721 DBG_PRINT(ERR_DBG, "%s: RTI init failed\n",
1731 * Initializing proper values as Pause threshold into all
1732 * the 8 Queues on Rx side.
1734 writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q0q3);
1735 writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q4q7);
1737 /* Disable RMAC PAD STRIPPING */
1738 add = &bar0->mac_cfg;
1739 val64 = readq(&bar0->mac_cfg);
1740 val64 &= ~(MAC_CFG_RMAC_STRIP_PAD);
1741 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1742 writel((u32) (val64), add);
1743 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1744 writel((u32) (val64 >> 32), (add + 4));
1745 val64 = readq(&bar0->mac_cfg);
1747 /* Enable FCS stripping by adapter */
1748 add = &bar0->mac_cfg;
1749 val64 = readq(&bar0->mac_cfg);
1750 val64 |= MAC_CFG_RMAC_STRIP_FCS;
1751 if (nic->device_type == XFRAME_II_DEVICE)
1752 writeq(val64, &bar0->mac_cfg);
1754 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1755 writel((u32) (val64), add);
1756 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1757 writel((u32) (val64 >> 32), (add + 4));
1761 * Set the time value to be inserted in the pause frame
1762 * generated by xena.
1764 val64 = readq(&bar0->rmac_pause_cfg);
1765 val64 &= ~(RMAC_PAUSE_HG_PTIME(0xffff));
1766 val64 |= RMAC_PAUSE_HG_PTIME(nic->mac_control.rmac_pause_time);
1767 writeq(val64, &bar0->rmac_pause_cfg);
1770 * Set the Threshold Limit for Generating the pause frame
1771 * If the amount of data in any Queue exceeds ratio of
1772 * (mac_control.mc_pause_threshold_q0q3 or q4q7)/256
1773 * pause frame is generated
1776 for (i = 0; i < 4; i++) {
1777 val64 |= (((u64)0xFF00 |
1778 nic->mac_control.mc_pause_threshold_q0q3)
1781 writeq(val64, &bar0->mc_pause_thresh_q0q3);
1784 for (i = 0; i < 4; i++) {
1785 val64 |= (((u64)0xFF00 |
1786 nic->mac_control.mc_pause_threshold_q4q7)
1789 writeq(val64, &bar0->mc_pause_thresh_q4q7);
1792 * TxDMA will stop Read request if the number of read split has
1793 * exceeded the limit pointed by shared_splits
1795 val64 = readq(&bar0->pic_control);
1796 val64 |= PIC_CNTL_SHARED_SPLITS(shared_splits);
1797 writeq(val64, &bar0->pic_control);
1799 if (nic->config.bus_speed == 266) {
1800 writeq(TXREQTO_VAL(0x7f) | TXREQTO_EN, &bar0->txreqtimeout);
1801 writeq(0x0, &bar0->read_retry_delay);
1802 writeq(0x0, &bar0->write_retry_delay);
1806 * Programming the Herc to split every write transaction
1807 * that does not start on an ADB to reduce disconnects.
1809 if (nic->device_type == XFRAME_II_DEVICE) {
1810 val64 = FAULT_BEHAVIOUR | EXT_REQ_EN |
1811 MISC_LINK_STABILITY_PRD(3);
1812 writeq(val64, &bar0->misc_control);
1813 val64 = readq(&bar0->pic_control2);
1814 val64 &= ~(s2BIT(13)|s2BIT(14)|s2BIT(15));
1815 writeq(val64, &bar0->pic_control2);
1817 if (strstr(nic->product_name, "CX4")) {
1818 val64 = TMAC_AVG_IPG(0x17);
1819 writeq(val64, &bar0->tmac_avg_ipg);
1824 #define LINK_UP_DOWN_INTERRUPT 1
1825 #define MAC_RMAC_ERR_TIMER 2
1827 static int s2io_link_fault_indication(struct s2io_nic *nic)
1829 if (nic->device_type == XFRAME_II_DEVICE)
1830 return LINK_UP_DOWN_INTERRUPT;
1832 return MAC_RMAC_ERR_TIMER;
1836 * do_s2io_write_bits - update alarm bits in alarm register
1837 * @value: alarm bits
1838 * @flag: interrupt status
1839 * @addr: address value
1840 * Description: update alarm bits in alarm register
1844 static void do_s2io_write_bits(u64 value, int flag, void __iomem *addr)
1848 temp64 = readq(addr);
1850 if (flag == ENABLE_INTRS)
1851 temp64 &= ~((u64)value);
1853 temp64 |= ((u64)value);
1854 writeq(temp64, addr);
1857 static void en_dis_err_alarms(struct s2io_nic *nic, u16 mask, int flag)
1859 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1860 register u64 gen_int_mask = 0;
1863 writeq(DISABLE_ALL_INTRS, &bar0->general_int_mask);
1864 if (mask & TX_DMA_INTR) {
1865 gen_int_mask |= TXDMA_INT_M;
1867 do_s2io_write_bits(TXDMA_TDA_INT | TXDMA_PFC_INT |
1868 TXDMA_PCC_INT | TXDMA_TTI_INT |
1869 TXDMA_LSO_INT | TXDMA_TPA_INT |
1870 TXDMA_SM_INT, flag, &bar0->txdma_int_mask);
1872 do_s2io_write_bits(PFC_ECC_DB_ERR | PFC_SM_ERR_ALARM |
1873 PFC_MISC_0_ERR | PFC_MISC_1_ERR |
1874 PFC_PCIX_ERR | PFC_ECC_SG_ERR, flag,
1875 &bar0->pfc_err_mask);
1877 do_s2io_write_bits(TDA_Fn_ECC_DB_ERR | TDA_SM0_ERR_ALARM |
1878 TDA_SM1_ERR_ALARM | TDA_Fn_ECC_SG_ERR |
1879 TDA_PCIX_ERR, flag, &bar0->tda_err_mask);
1881 do_s2io_write_bits(PCC_FB_ECC_DB_ERR | PCC_TXB_ECC_DB_ERR |
1882 PCC_SM_ERR_ALARM | PCC_WR_ERR_ALARM |
1883 PCC_N_SERR | PCC_6_COF_OV_ERR |
1884 PCC_7_COF_OV_ERR | PCC_6_LSO_OV_ERR |
1885 PCC_7_LSO_OV_ERR | PCC_FB_ECC_SG_ERR |
1887 flag, &bar0->pcc_err_mask);
1889 do_s2io_write_bits(TTI_SM_ERR_ALARM | TTI_ECC_SG_ERR |
1890 TTI_ECC_DB_ERR, flag, &bar0->tti_err_mask);
1892 do_s2io_write_bits(LSO6_ABORT | LSO7_ABORT |
1893 LSO6_SM_ERR_ALARM | LSO7_SM_ERR_ALARM |
1894 LSO6_SEND_OFLOW | LSO7_SEND_OFLOW,
1895 flag, &bar0->lso_err_mask);
1897 do_s2io_write_bits(TPA_SM_ERR_ALARM | TPA_TX_FRM_DROP,
1898 flag, &bar0->tpa_err_mask);
1900 do_s2io_write_bits(SM_SM_ERR_ALARM, flag, &bar0->sm_err_mask);
1903 if (mask & TX_MAC_INTR) {
1904 gen_int_mask |= TXMAC_INT_M;
1905 do_s2io_write_bits(MAC_INT_STATUS_TMAC_INT, flag,
1906 &bar0->mac_int_mask);
1907 do_s2io_write_bits(TMAC_TX_BUF_OVRN | TMAC_TX_SM_ERR |
1908 TMAC_ECC_SG_ERR | TMAC_ECC_DB_ERR |
1909 TMAC_DESC_ECC_SG_ERR | TMAC_DESC_ECC_DB_ERR,
1910 flag, &bar0->mac_tmac_err_mask);
1913 if (mask & TX_XGXS_INTR) {
1914 gen_int_mask |= TXXGXS_INT_M;
1915 do_s2io_write_bits(XGXS_INT_STATUS_TXGXS, flag,
1916 &bar0->xgxs_int_mask);
1917 do_s2io_write_bits(TXGXS_ESTORE_UFLOW | TXGXS_TX_SM_ERR |
1918 TXGXS_ECC_SG_ERR | TXGXS_ECC_DB_ERR,
1919 flag, &bar0->xgxs_txgxs_err_mask);
1922 if (mask & RX_DMA_INTR) {
1923 gen_int_mask |= RXDMA_INT_M;
1924 do_s2io_write_bits(RXDMA_INT_RC_INT_M | RXDMA_INT_RPA_INT_M |
1925 RXDMA_INT_RDA_INT_M | RXDMA_INT_RTI_INT_M,
1926 flag, &bar0->rxdma_int_mask);
1927 do_s2io_write_bits(RC_PRCn_ECC_DB_ERR | RC_FTC_ECC_DB_ERR |
1928 RC_PRCn_SM_ERR_ALARM | RC_FTC_SM_ERR_ALARM |
1929 RC_PRCn_ECC_SG_ERR | RC_FTC_ECC_SG_ERR |
1930 RC_RDA_FAIL_WR_Rn, flag, &bar0->rc_err_mask);
1931 do_s2io_write_bits(PRC_PCI_AB_RD_Rn | PRC_PCI_AB_WR_Rn |
1932 PRC_PCI_AB_F_WR_Rn | PRC_PCI_DP_RD_Rn |
1933 PRC_PCI_DP_WR_Rn | PRC_PCI_DP_F_WR_Rn, flag,
1934 &bar0->prc_pcix_err_mask);
1935 do_s2io_write_bits(RPA_SM_ERR_ALARM | RPA_CREDIT_ERR |
1936 RPA_ECC_SG_ERR | RPA_ECC_DB_ERR, flag,
1937 &bar0->rpa_err_mask);
1938 do_s2io_write_bits(RDA_RXDn_ECC_DB_ERR | RDA_FRM_ECC_DB_N_AERR |
1939 RDA_SM1_ERR_ALARM | RDA_SM0_ERR_ALARM |
1940 RDA_RXD_ECC_DB_SERR | RDA_RXDn_ECC_SG_ERR |
1941 RDA_FRM_ECC_SG_ERR |
1942 RDA_MISC_ERR|RDA_PCIX_ERR,
1943 flag, &bar0->rda_err_mask);
1944 do_s2io_write_bits(RTI_SM_ERR_ALARM |
1945 RTI_ECC_SG_ERR | RTI_ECC_DB_ERR,
1946 flag, &bar0->rti_err_mask);
1949 if (mask & RX_MAC_INTR) {
1950 gen_int_mask |= RXMAC_INT_M;
1951 do_s2io_write_bits(MAC_INT_STATUS_RMAC_INT, flag,
1952 &bar0->mac_int_mask);
1953 interruptible = (RMAC_RX_BUFF_OVRN | RMAC_RX_SM_ERR |
1954 RMAC_UNUSED_INT | RMAC_SINGLE_ECC_ERR |
1955 RMAC_DOUBLE_ECC_ERR);
1956 if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER)
1957 interruptible |= RMAC_LINK_STATE_CHANGE_INT;
1958 do_s2io_write_bits(interruptible,
1959 flag, &bar0->mac_rmac_err_mask);
1962 if (mask & RX_XGXS_INTR) {
1963 gen_int_mask |= RXXGXS_INT_M;
1964 do_s2io_write_bits(XGXS_INT_STATUS_RXGXS, flag,
1965 &bar0->xgxs_int_mask);
1966 do_s2io_write_bits(RXGXS_ESTORE_OFLOW | RXGXS_RX_SM_ERR, flag,
1967 &bar0->xgxs_rxgxs_err_mask);
1970 if (mask & MC_INTR) {
1971 gen_int_mask |= MC_INT_M;
1972 do_s2io_write_bits(MC_INT_MASK_MC_INT,
1973 flag, &bar0->mc_int_mask);
1974 do_s2io_write_bits(MC_ERR_REG_SM_ERR | MC_ERR_REG_ECC_ALL_SNG |
1975 MC_ERR_REG_ECC_ALL_DBL | PLL_LOCK_N, flag,
1976 &bar0->mc_err_mask);
1978 nic->general_int_mask = gen_int_mask;
1980 /* Remove this line when alarm interrupts are enabled */
1981 nic->general_int_mask = 0;
1985 * en_dis_able_nic_intrs - Enable or Disable the interrupts
1986 * @nic: device private variable,
1987 * @mask: A mask indicating which Intr block must be modified and,
1988 * @flag: A flag indicating whether to enable or disable the Intrs.
1989 * Description: This function will either disable or enable the interrupts
1990 * depending on the flag argument. The mask argument can be used to
1991 * enable/disable any Intr block.
1992 * Return Value: NONE.
1995 static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag)
1997 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1998 register u64 temp64 = 0, intr_mask = 0;
2000 intr_mask = nic->general_int_mask;
2002 /* Top level interrupt classification */
2003 /* PIC Interrupts */
2004 if (mask & TX_PIC_INTR) {
2005 /* Enable PIC Intrs in the general intr mask register */
2006 intr_mask |= TXPIC_INT_M;
2007 if (flag == ENABLE_INTRS) {
2009 * If Hercules adapter enable GPIO otherwise
2010 * disable all PCIX, Flash, MDIO, IIC and GPIO
2011 * interrupts for now.
2014 if (s2io_link_fault_indication(nic) ==
2015 LINK_UP_DOWN_INTERRUPT) {
2016 do_s2io_write_bits(PIC_INT_GPIO, flag,
2017 &bar0->pic_int_mask);
2018 do_s2io_write_bits(GPIO_INT_MASK_LINK_UP, flag,
2019 &bar0->gpio_int_mask);
2021 writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
2022 } else if (flag == DISABLE_INTRS) {
2024 * Disable PIC Intrs in the general
2025 * intr mask register
2027 writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
2031 /* Tx traffic interrupts */
2032 if (mask & TX_TRAFFIC_INTR) {
2033 intr_mask |= TXTRAFFIC_INT_M;
2034 if (flag == ENABLE_INTRS) {
2036 * Enable all the Tx side interrupts
2037 * writing 0 Enables all 64 TX interrupt levels
2039 writeq(0x0, &bar0->tx_traffic_mask);
2040 } else if (flag == DISABLE_INTRS) {
2042 * Disable Tx Traffic Intrs in the general intr mask
2045 writeq(DISABLE_ALL_INTRS, &bar0->tx_traffic_mask);
2049 /* Rx traffic interrupts */
2050 if (mask & RX_TRAFFIC_INTR) {
2051 intr_mask |= RXTRAFFIC_INT_M;
2052 if (flag == ENABLE_INTRS) {
2053 /* writing 0 Enables all 8 RX interrupt levels */
2054 writeq(0x0, &bar0->rx_traffic_mask);
2055 } else if (flag == DISABLE_INTRS) {
2057 * Disable Rx Traffic Intrs in the general intr mask
2060 writeq(DISABLE_ALL_INTRS, &bar0->rx_traffic_mask);
2064 temp64 = readq(&bar0->general_int_mask);
2065 if (flag == ENABLE_INTRS)
2066 temp64 &= ~((u64)intr_mask);
2068 temp64 = DISABLE_ALL_INTRS;
2069 writeq(temp64, &bar0->general_int_mask);
2071 nic->general_int_mask = readq(&bar0->general_int_mask);
2075 * verify_pcc_quiescent- Checks for PCC quiescent state
2076 * Return: 1 If PCC is quiescence
2077 * 0 If PCC is not quiescence
2079 static int verify_pcc_quiescent(struct s2io_nic *sp, int flag)
2082 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2083 u64 val64 = readq(&bar0->adapter_status);
2085 herc = (sp->device_type == XFRAME_II_DEVICE);
2087 if (flag == false) {
2088 if ((!herc && (sp->pdev->revision >= 4)) || herc) {
2089 if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE))
2092 if (!(val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE))
2096 if ((!herc && (sp->pdev->revision >= 4)) || herc) {
2097 if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) ==
2098 ADAPTER_STATUS_RMAC_PCC_IDLE))
2101 if (((val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) ==
2102 ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE))
2110 * verify_xena_quiescence - Checks whether the H/W is ready
2111 * Description: Returns whether the H/W is ready to go or not. Depending
2112 * on whether adapter enable bit was written or not the comparison
2113 * differs and the calling function passes the input argument flag to
2115 * Return: 1 If xena is quiescence
2116 * 0 If Xena is not quiescence
2119 static int verify_xena_quiescence(struct s2io_nic *sp)
2122 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2123 u64 val64 = readq(&bar0->adapter_status);
2124 mode = s2io_verify_pci_mode(sp);
2126 if (!(val64 & ADAPTER_STATUS_TDMA_READY)) {
2127 DBG_PRINT(ERR_DBG, "TDMA is not ready!\n");
2130 if (!(val64 & ADAPTER_STATUS_RDMA_READY)) {
2131 DBG_PRINT(ERR_DBG, "RDMA is not ready!\n");
2134 if (!(val64 & ADAPTER_STATUS_PFC_READY)) {
2135 DBG_PRINT(ERR_DBG, "PFC is not ready!\n");
2138 if (!(val64 & ADAPTER_STATUS_TMAC_BUF_EMPTY)) {
2139 DBG_PRINT(ERR_DBG, "TMAC BUF is not empty!\n");
2142 if (!(val64 & ADAPTER_STATUS_PIC_QUIESCENT)) {
2143 DBG_PRINT(ERR_DBG, "PIC is not QUIESCENT!\n");
2146 if (!(val64 & ADAPTER_STATUS_MC_DRAM_READY)) {
2147 DBG_PRINT(ERR_DBG, "MC_DRAM is not ready!\n");
2150 if (!(val64 & ADAPTER_STATUS_MC_QUEUES_READY)) {
2151 DBG_PRINT(ERR_DBG, "MC_QUEUES is not ready!\n");
2154 if (!(val64 & ADAPTER_STATUS_M_PLL_LOCK)) {
2155 DBG_PRINT(ERR_DBG, "M_PLL is not locked!\n");
2160 * In PCI 33 mode, the P_PLL is not used, and therefore,
2161 * the the P_PLL_LOCK bit in the adapter_status register will
2164 if (!(val64 & ADAPTER_STATUS_P_PLL_LOCK) &&
2165 sp->device_type == XFRAME_II_DEVICE &&
2166 mode != PCI_MODE_PCI_33) {
2167 DBG_PRINT(ERR_DBG, "P_PLL is not locked!\n");
2170 if (!((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
2171 ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
2172 DBG_PRINT(ERR_DBG, "RC_PRC is not QUIESCENT!\n");
2179 * fix_mac_address - Fix for Mac addr problem on Alpha platforms
2180 * @sp: Pointer to device specifc structure
2182 * New procedure to clear mac address reading problems on Alpha platforms
2186 static void fix_mac_address(struct s2io_nic *sp)
2188 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2191 while (fix_mac[i] != END_SIGN) {
2192 writeq(fix_mac[i++], &bar0->gpio_control);
2194 (void) readq(&bar0->gpio_control);
2199 * start_nic - Turns the device on
2200 * @nic : device private variable.
2202 * This function actually turns the device on. Before this function is
2203 * called,all Registers are configured from their reset states
2204 * and shared memory is allocated but the NIC is still quiescent. On
2205 * calling this function, the device interrupts are cleared and the NIC is
2206 * literally switched on by writing into the adapter control register.
2208 * SUCCESS on success and -1 on failure.
2211 static int start_nic(struct s2io_nic *nic)
2213 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2214 struct net_device *dev = nic->dev;
2215 register u64 val64 = 0;
2217 struct config_param *config = &nic->config;
2218 struct mac_info *mac_control = &nic->mac_control;
2220 /* PRC Initialization and configuration */
2221 for (i = 0; i < config->rx_ring_num; i++) {
2222 struct ring_info *ring = &mac_control->rings[i];
2224 writeq((u64)ring->rx_blocks[0].block_dma_addr,
2225 &bar0->prc_rxd0_n[i]);
2227 val64 = readq(&bar0->prc_ctrl_n[i]);
2228 if (nic->rxd_mode == RXD_MODE_1)
2229 val64 |= PRC_CTRL_RC_ENABLED;
2231 val64 |= PRC_CTRL_RC_ENABLED | PRC_CTRL_RING_MODE_3;
2232 if (nic->device_type == XFRAME_II_DEVICE)
2233 val64 |= PRC_CTRL_GROUP_READS;
2234 val64 &= ~PRC_CTRL_RXD_BACKOFF_INTERVAL(0xFFFFFF);
2235 val64 |= PRC_CTRL_RXD_BACKOFF_INTERVAL(0x1000);
2236 writeq(val64, &bar0->prc_ctrl_n[i]);
2239 if (nic->rxd_mode == RXD_MODE_3B) {
2240 /* Enabling 2 buffer mode by writing into Rx_pa_cfg reg. */
2241 val64 = readq(&bar0->rx_pa_cfg);
2242 val64 |= RX_PA_CFG_IGNORE_L2_ERR;
2243 writeq(val64, &bar0->rx_pa_cfg);
2246 if (vlan_tag_strip == 0) {
2247 val64 = readq(&bar0->rx_pa_cfg);
2248 val64 &= ~RX_PA_CFG_STRIP_VLAN_TAG;
2249 writeq(val64, &bar0->rx_pa_cfg);
2250 nic->vlan_strip_flag = 0;
2254 * Enabling MC-RLDRAM. After enabling the device, we timeout
2255 * for around 100ms, which is approximately the time required
2256 * for the device to be ready for operation.
2258 val64 = readq(&bar0->mc_rldram_mrs);
2259 val64 |= MC_RLDRAM_QUEUE_SIZE_ENABLE | MC_RLDRAM_MRS_ENABLE;
2260 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
2261 val64 = readq(&bar0->mc_rldram_mrs);
2263 msleep(100); /* Delay by around 100 ms. */
2265 /* Enabling ECC Protection. */
2266 val64 = readq(&bar0->adapter_control);
2267 val64 &= ~ADAPTER_ECC_EN;
2268 writeq(val64, &bar0->adapter_control);
2271 * Verify if the device is ready to be enabled, if so enable
2274 val64 = readq(&bar0->adapter_status);
2275 if (!verify_xena_quiescence(nic)) {
2276 DBG_PRINT(ERR_DBG, "%s: device is not ready, "
2277 "Adapter status reads: 0x%llx\n",
2278 dev->name, (unsigned long long)val64);
2283 * With some switches, link might be already up at this point.
2284 * Because of this weird behavior, when we enable laser,
2285 * we may not get link. We need to handle this. We cannot
2286 * figure out which switch is misbehaving. So we are forced to
2287 * make a global change.
2290 /* Enabling Laser. */
2291 val64 = readq(&bar0->adapter_control);
2292 val64 |= ADAPTER_EOI_TX_ON;
2293 writeq(val64, &bar0->adapter_control);
2295 if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
2297 * Dont see link state interrupts initially on some switches,
2298 * so directly scheduling the link state task here.
2300 schedule_work(&nic->set_link_task);
2302 /* SXE-002: Initialize link and activity LED */
2303 subid = nic->pdev->subsystem_device;
2304 if (((subid & 0xFF) >= 0x07) &&
2305 (nic->device_type == XFRAME_I_DEVICE)) {
2306 val64 = readq(&bar0->gpio_control);
2307 val64 |= 0x0000800000000000ULL;
2308 writeq(val64, &bar0->gpio_control);
2309 val64 = 0x0411040400000000ULL;
2310 writeq(val64, (void __iomem *)bar0 + 0x2700);
2316 * s2io_txdl_getskb - Get the skb from txdl, unmap and return skb
2318 static struct sk_buff *s2io_txdl_getskb(struct fifo_info *fifo_data,
2319 struct TxD *txdlp, int get_off)
2321 struct s2io_nic *nic = fifo_data->nic;
2322 struct sk_buff *skb;
2327 if (txds->Host_Control == (u64)(long)fifo_data->ufo_in_band_v) {
2328 pci_unmap_single(nic->pdev, (dma_addr_t)txds->Buffer_Pointer,
2329 sizeof(u64), PCI_DMA_TODEVICE);
2333 skb = (struct sk_buff *)((unsigned long)txds->Host_Control);
2335 memset(txdlp, 0, (sizeof(struct TxD) * fifo_data->max_txds));
2338 pci_unmap_single(nic->pdev, (dma_addr_t)txds->Buffer_Pointer,
2339 skb_headlen(skb), PCI_DMA_TODEVICE);
2340 frg_cnt = skb_shinfo(skb)->nr_frags;
2343 for (j = 0; j < frg_cnt; j++, txds++) {
2344 const skb_frag_t *frag = &skb_shinfo(skb)->frags[j];
2345 if (!txds->Buffer_Pointer)
2347 pci_unmap_page(nic->pdev,
2348 (dma_addr_t)txds->Buffer_Pointer,
2349 skb_frag_size(frag), PCI_DMA_TODEVICE);
2352 memset(txdlp, 0, (sizeof(struct TxD) * fifo_data->max_txds));
2357 * free_tx_buffers - Free all queued Tx buffers
2358 * @nic : device private variable.
2360 * Free all queued Tx buffers.
2361 * Return Value: void
2364 static void free_tx_buffers(struct s2io_nic *nic)
2366 struct net_device *dev = nic->dev;
2367 struct sk_buff *skb;
2371 struct config_param *config = &nic->config;
2372 struct mac_info *mac_control = &nic->mac_control;
2373 struct stat_block *stats = mac_control->stats_info;
2374 struct swStat *swstats = &stats->sw_stat;
2376 for (i = 0; i < config->tx_fifo_num; i++) {
2377 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
2378 struct fifo_info *fifo = &mac_control->fifos[i];
2379 unsigned long flags;
2381 spin_lock_irqsave(&fifo->tx_lock, flags);
2382 for (j = 0; j < tx_cfg->fifo_len; j++) {
2383 txdp = fifo->list_info[j].list_virt_addr;
2384 skb = s2io_txdl_getskb(&mac_control->fifos[i], txdp, j);
2386 swstats->mem_freed += skb->truesize;
2392 "%s: forcibly freeing %d skbs on FIFO%d\n",
2394 fifo->tx_curr_get_info.offset = 0;
2395 fifo->tx_curr_put_info.offset = 0;
2396 spin_unlock_irqrestore(&fifo->tx_lock, flags);
2401 * stop_nic - To stop the nic
2402 * @nic ; device private variable.
2404 * This function does exactly the opposite of what the start_nic()
2405 * function does. This function is called to stop the device.
2410 static void stop_nic(struct s2io_nic *nic)
2412 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2413 register u64 val64 = 0;
2416 /* Disable all interrupts */
2417 en_dis_err_alarms(nic, ENA_ALL_INTRS, DISABLE_INTRS);
2418 interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
2419 interruptible |= TX_PIC_INTR;
2420 en_dis_able_nic_intrs(nic, interruptible, DISABLE_INTRS);
2422 /* Clearing Adapter_En bit of ADAPTER_CONTROL Register */
2423 val64 = readq(&bar0->adapter_control);
2424 val64 &= ~(ADAPTER_CNTL_EN);
2425 writeq(val64, &bar0->adapter_control);
2429 * fill_rx_buffers - Allocates the Rx side skbs
2430 * @ring_info: per ring structure
2431 * @from_card_up: If this is true, we will map the buffer to get
2432 * the dma address for buf0 and buf1 to give it to the card.
2433 * Else we will sync the already mapped buffer to give it to the card.
2435 * The function allocates Rx side skbs and puts the physical
2436 * address of these buffers into the RxD buffer pointers, so that the NIC
2437 * can DMA the received frame into these locations.
2438 * The NIC supports 3 receive modes, viz
2440 * 2. three buffer and
2441 * 3. Five buffer modes.
2442 * Each mode defines how many fragments the received frame will be split
2443 * up into by the NIC. The frame is split into L3 header, L4 Header,
2444 * L4 payload in three buffer mode and in 5 buffer mode, L4 payload itself
2445 * is split into 3 fragments. As of now only single buffer mode is
2448 * SUCCESS on success or an appropriate -ve value on failure.
2450 static int fill_rx_buffers(struct s2io_nic *nic, struct ring_info *ring,
2453 struct sk_buff *skb;
2455 int off, size, block_no, block_no1;
2460 struct RxD_t *first_rxdp = NULL;
2461 u64 Buffer0_ptr = 0, Buffer1_ptr = 0;
2465 struct swStat *swstats = &ring->nic->mac_control.stats_info->sw_stat;
2467 alloc_cnt = ring->pkt_cnt - ring->rx_bufs_left;
2469 block_no1 = ring->rx_curr_get_info.block_index;
2470 while (alloc_tab < alloc_cnt) {
2471 block_no = ring->rx_curr_put_info.block_index;
2473 off = ring->rx_curr_put_info.offset;
2475 rxdp = ring->rx_blocks[block_no].rxds[off].virt_addr;
2477 rxd_index = off + 1;
2479 rxd_index += (block_no * ring->rxd_count);
2481 if ((block_no == block_no1) &&
2482 (off == ring->rx_curr_get_info.offset) &&
2483 (rxdp->Host_Control)) {
2484 DBG_PRINT(INTR_DBG, "%s: Get and Put info equated\n",
2488 if (off && (off == ring->rxd_count)) {
2489 ring->rx_curr_put_info.block_index++;
2490 if (ring->rx_curr_put_info.block_index ==
2492 ring->rx_curr_put_info.block_index = 0;
2493 block_no = ring->rx_curr_put_info.block_index;
2495 ring->rx_curr_put_info.offset = off;
2496 rxdp = ring->rx_blocks[block_no].block_virt_addr;
2497 DBG_PRINT(INTR_DBG, "%s: Next block at: %p\n",
2498 ring->dev->name, rxdp);
2502 if ((rxdp->Control_1 & RXD_OWN_XENA) &&
2503 ((ring->rxd_mode == RXD_MODE_3B) &&
2504 (rxdp->Control_2 & s2BIT(0)))) {
2505 ring->rx_curr_put_info.offset = off;
2508 /* calculate size of skb based on ring mode */
2510 HEADER_ETHERNET_II_802_3_SIZE +
2511 HEADER_802_2_SIZE + HEADER_SNAP_SIZE;
2512 if (ring->rxd_mode == RXD_MODE_1)
2513 size += NET_IP_ALIGN;
2515 size = ring->mtu + ALIGN_SIZE + BUF0_LEN + 4;
2518 skb = netdev_alloc_skb(nic->dev, size);
2520 DBG_PRINT(INFO_DBG, "%s: Could not allocate skb\n",
2524 first_rxdp->Control_1 |= RXD_OWN_XENA;
2526 swstats->mem_alloc_fail_cnt++;
2530 swstats->mem_allocated += skb->truesize;
2532 if (ring->rxd_mode == RXD_MODE_1) {
2533 /* 1 buffer mode - normal operation mode */
2534 rxdp1 = (struct RxD1 *)rxdp;
2535 memset(rxdp, 0, sizeof(struct RxD1));
2536 skb_reserve(skb, NET_IP_ALIGN);
2537 rxdp1->Buffer0_ptr =
2538 pci_map_single(ring->pdev, skb->data,
2539 size - NET_IP_ALIGN,
2540 PCI_DMA_FROMDEVICE);
2541 if (pci_dma_mapping_error(nic->pdev,
2542 rxdp1->Buffer0_ptr))
2543 goto pci_map_failed;
2546 SET_BUFFER0_SIZE_1(size - NET_IP_ALIGN);
2547 rxdp->Host_Control = (unsigned long)skb;
2548 } else if (ring->rxd_mode == RXD_MODE_3B) {
2551 * 2 buffer mode provides 128
2552 * byte aligned receive buffers.
2555 rxdp3 = (struct RxD3 *)rxdp;
2556 /* save buffer pointers to avoid frequent dma mapping */
2557 Buffer0_ptr = rxdp3->Buffer0_ptr;
2558 Buffer1_ptr = rxdp3->Buffer1_ptr;
2559 memset(rxdp, 0, sizeof(struct RxD3));
2560 /* restore the buffer pointers for dma sync*/
2561 rxdp3->Buffer0_ptr = Buffer0_ptr;
2562 rxdp3->Buffer1_ptr = Buffer1_ptr;
2564 ba = &ring->ba[block_no][off];
2565 skb_reserve(skb, BUF0_LEN);
2566 tmp = (u64)(unsigned long)skb->data;
2569 skb->data = (void *) (unsigned long)tmp;
2570 skb_reset_tail_pointer(skb);
2573 rxdp3->Buffer0_ptr =
2574 pci_map_single(ring->pdev, ba->ba_0,
2576 PCI_DMA_FROMDEVICE);
2577 if (pci_dma_mapping_error(nic->pdev,
2578 rxdp3->Buffer0_ptr))
2579 goto pci_map_failed;
2581 pci_dma_sync_single_for_device(ring->pdev,
2582 (dma_addr_t)rxdp3->Buffer0_ptr,
2584 PCI_DMA_FROMDEVICE);
2586 rxdp->Control_2 = SET_BUFFER0_SIZE_3(BUF0_LEN);
2587 if (ring->rxd_mode == RXD_MODE_3B) {
2588 /* Two buffer mode */
2591 * Buffer2 will have L3/L4 header plus
2594 rxdp3->Buffer2_ptr = pci_map_single(ring->pdev,
2597 PCI_DMA_FROMDEVICE);
2599 if (pci_dma_mapping_error(nic->pdev,
2600 rxdp3->Buffer2_ptr))
2601 goto pci_map_failed;
2604 rxdp3->Buffer1_ptr =
2605 pci_map_single(ring->pdev,
2608 PCI_DMA_FROMDEVICE);
2610 if (pci_dma_mapping_error(nic->pdev,
2611 rxdp3->Buffer1_ptr)) {
2612 pci_unmap_single(ring->pdev,
2613 (dma_addr_t)(unsigned long)
2616 PCI_DMA_FROMDEVICE);
2617 goto pci_map_failed;
2620 rxdp->Control_2 |= SET_BUFFER1_SIZE_3(1);
2621 rxdp->Control_2 |= SET_BUFFER2_SIZE_3
2624 rxdp->Control_2 |= s2BIT(0);
2625 rxdp->Host_Control = (unsigned long) (skb);
2627 if (alloc_tab & ((1 << rxsync_frequency) - 1))
2628 rxdp->Control_1 |= RXD_OWN_XENA;
2630 if (off == (ring->rxd_count + 1))
2632 ring->rx_curr_put_info.offset = off;
2634 rxdp->Control_2 |= SET_RXD_MARKER;
2635 if (!(alloc_tab & ((1 << rxsync_frequency) - 1))) {
2638 first_rxdp->Control_1 |= RXD_OWN_XENA;
2642 ring->rx_bufs_left += 1;
2647 /* Transfer ownership of first descriptor to adapter just before
2648 * exiting. Before that, use memory barrier so that ownership
2649 * and other fields are seen by adapter correctly.
2653 first_rxdp->Control_1 |= RXD_OWN_XENA;
2659 swstats->pci_map_fail_cnt++;
2660 swstats->mem_freed += skb->truesize;
2661 dev_kfree_skb_irq(skb);
2665 static void free_rxd_blk(struct s2io_nic *sp, int ring_no, int blk)
2667 struct net_device *dev = sp->dev;
2669 struct sk_buff *skb;
2673 struct mac_info *mac_control = &sp->mac_control;
2674 struct stat_block *stats = mac_control->stats_info;
2675 struct swStat *swstats = &stats->sw_stat;
2677 for (j = 0 ; j < rxd_count[sp->rxd_mode]; j++) {
2678 rxdp = mac_control->rings[ring_no].
2679 rx_blocks[blk].rxds[j].virt_addr;
2680 skb = (struct sk_buff *)((unsigned long)rxdp->Host_Control);
2683 if (sp->rxd_mode == RXD_MODE_1) {
2684 rxdp1 = (struct RxD1 *)rxdp;
2685 pci_unmap_single(sp->pdev,
2686 (dma_addr_t)rxdp1->Buffer0_ptr,
2688 HEADER_ETHERNET_II_802_3_SIZE +
2689 HEADER_802_2_SIZE + HEADER_SNAP_SIZE,
2690 PCI_DMA_FROMDEVICE);
2691 memset(rxdp, 0, sizeof(struct RxD1));
2692 } else if (sp->rxd_mode == RXD_MODE_3B) {
2693 rxdp3 = (struct RxD3 *)rxdp;
2694 pci_unmap_single(sp->pdev,
2695 (dma_addr_t)rxdp3->Buffer0_ptr,
2697 PCI_DMA_FROMDEVICE);
2698 pci_unmap_single(sp->pdev,
2699 (dma_addr_t)rxdp3->Buffer1_ptr,
2701 PCI_DMA_FROMDEVICE);
2702 pci_unmap_single(sp->pdev,
2703 (dma_addr_t)rxdp3->Buffer2_ptr,
2705 PCI_DMA_FROMDEVICE);
2706 memset(rxdp, 0, sizeof(struct RxD3));
2708 swstats->mem_freed += skb->truesize;
2710 mac_control->rings[ring_no].rx_bufs_left -= 1;
2715 * free_rx_buffers - Frees all Rx buffers
2716 * @sp: device private variable.
2718 * This function will free all Rx buffers allocated by host.
2723 static void free_rx_buffers(struct s2io_nic *sp)
2725 struct net_device *dev = sp->dev;
2726 int i, blk = 0, buf_cnt = 0;
2727 struct config_param *config = &sp->config;
2728 struct mac_info *mac_control = &sp->mac_control;
2730 for (i = 0; i < config->rx_ring_num; i++) {
2731 struct ring_info *ring = &mac_control->rings[i];
2733 for (blk = 0; blk < rx_ring_sz[i]; blk++)
2734 free_rxd_blk(sp, i, blk);
2736 ring->rx_curr_put_info.block_index = 0;
2737 ring->rx_curr_get_info.block_index = 0;
2738 ring->rx_curr_put_info.offset = 0;
2739 ring->rx_curr_get_info.offset = 0;
2740 ring->rx_bufs_left = 0;
2741 DBG_PRINT(INIT_DBG, "%s: Freed 0x%x Rx Buffers on ring%d\n",
2742 dev->name, buf_cnt, i);
2746 static int s2io_chk_rx_buffers(struct s2io_nic *nic, struct ring_info *ring)
2748 if (fill_rx_buffers(nic, ring, 0) == -ENOMEM) {
2749 DBG_PRINT(INFO_DBG, "%s: Out of memory in Rx Intr!!\n",
2756 * s2io_poll - Rx interrupt handler for NAPI support
2757 * @napi : pointer to the napi structure.
2758 * @budget : The number of packets that were budgeted to be processed
2759 * during one pass through the 'Poll" function.
2761 * Comes into picture only if NAPI support has been incorporated. It does
2762 * the same thing that rx_intr_handler does, but not in a interrupt context
2763 * also It will process only a given number of packets.
2765 * 0 on success and 1 if there are No Rx packets to be processed.
2768 static int s2io_poll_msix(struct napi_struct *napi, int budget)
2770 struct ring_info *ring = container_of(napi, struct ring_info, napi);
2771 struct net_device *dev = ring->dev;
2772 int pkts_processed = 0;
2773 u8 __iomem *addr = NULL;
2775 struct s2io_nic *nic = netdev_priv(dev);
2776 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2777 int budget_org = budget;
2779 if (unlikely(!is_s2io_card_up(nic)))
2782 pkts_processed = rx_intr_handler(ring, budget);
2783 s2io_chk_rx_buffers(nic, ring);
2785 if (pkts_processed < budget_org) {
2786 napi_complete(napi);
2787 /*Re Enable MSI-Rx Vector*/
2788 addr = (u8 __iomem *)&bar0->xmsi_mask_reg;
2789 addr += 7 - ring->ring_no;
2790 val8 = (ring->ring_no == 0) ? 0x3f : 0xbf;
2794 return pkts_processed;
2797 static int s2io_poll_inta(struct napi_struct *napi, int budget)
2799 struct s2io_nic *nic = container_of(napi, struct s2io_nic, napi);
2800 int pkts_processed = 0;
2801 int ring_pkts_processed, i;
2802 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2803 int budget_org = budget;
2804 struct config_param *config = &nic->config;
2805 struct mac_info *mac_control = &nic->mac_control;
2807 if (unlikely(!is_s2io_card_up(nic)))
2810 for (i = 0; i < config->rx_ring_num; i++) {
2811 struct ring_info *ring = &mac_control->rings[i];
2812 ring_pkts_processed = rx_intr_handler(ring, budget);
2813 s2io_chk_rx_buffers(nic, ring);
2814 pkts_processed += ring_pkts_processed;
2815 budget -= ring_pkts_processed;
2819 if (pkts_processed < budget_org) {
2820 napi_complete(napi);
2821 /* Re enable the Rx interrupts for the ring */
2822 writeq(0, &bar0->rx_traffic_mask);
2823 readl(&bar0->rx_traffic_mask);
2825 return pkts_processed;
2828 #ifdef CONFIG_NET_POLL_CONTROLLER
2830 * s2io_netpoll - netpoll event handler entry point
2831 * @dev : pointer to the device structure.
2833 * This function will be called by upper layer to check for events on the
2834 * interface in situations where interrupts are disabled. It is used for
2835 * specific in-kernel networking tasks, such as remote consoles and kernel
2836 * debugging over the network (example netdump in RedHat).
2838 static void s2io_netpoll(struct net_device *dev)
2840 struct s2io_nic *nic = netdev_priv(dev);
2841 const int irq = nic->pdev->irq;
2842 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2843 u64 val64 = 0xFFFFFFFFFFFFFFFFULL;
2845 struct config_param *config = &nic->config;
2846 struct mac_info *mac_control = &nic->mac_control;
2848 if (pci_channel_offline(nic->pdev))
2853 writeq(val64, &bar0->rx_traffic_int);
2854 writeq(val64, &bar0->tx_traffic_int);
2856 /* we need to free up the transmitted skbufs or else netpoll will
2857 * run out of skbs and will fail and eventually netpoll application such
2858 * as netdump will fail.
2860 for (i = 0; i < config->tx_fifo_num; i++)
2861 tx_intr_handler(&mac_control->fifos[i]);
2863 /* check for received packet and indicate up to network */
2864 for (i = 0; i < config->rx_ring_num; i++) {
2865 struct ring_info *ring = &mac_control->rings[i];
2867 rx_intr_handler(ring, 0);
2870 for (i = 0; i < config->rx_ring_num; i++) {
2871 struct ring_info *ring = &mac_control->rings[i];
2873 if (fill_rx_buffers(nic, ring, 0) == -ENOMEM) {
2875 "%s: Out of memory in Rx Netpoll!!\n",
2885 * rx_intr_handler - Rx interrupt handler
2886 * @ring_info: per ring structure.
2887 * @budget: budget for napi processing.
2889 * If the interrupt is because of a received frame or if the
2890 * receive ring contains fresh as yet un-processed frames,this function is
2891 * called. It picks out the RxD at which place the last Rx processing had
2892 * stopped and sends the skb to the OSM's Rx handler and then increments
2895 * No. of napi packets processed.
2897 static int rx_intr_handler(struct ring_info *ring_data, int budget)
2899 int get_block, put_block;
2900 struct rx_curr_get_info get_info, put_info;
2902 struct sk_buff *skb;
2903 int pkt_cnt = 0, napi_pkts = 0;
2911 get_info = ring_data->rx_curr_get_info;
2912 get_block = get_info.block_index;
2913 memcpy(&put_info, &ring_data->rx_curr_put_info, sizeof(put_info));
2914 put_block = put_info.block_index;
2915 rxdp = ring_data->rx_blocks[get_block].rxds[get_info.offset].virt_addr;
2917 while (RXD_IS_UP2DT(rxdp)) {
2919 * If your are next to put index then it's
2920 * FIFO full condition
2922 if ((get_block == put_block) &&
2923 (get_info.offset + 1) == put_info.offset) {
2924 DBG_PRINT(INTR_DBG, "%s: Ring Full\n",
2925 ring_data->dev->name);
2928 skb = (struct sk_buff *)((unsigned long)rxdp->Host_Control);
2930 DBG_PRINT(ERR_DBG, "%s: NULL skb in Rx Intr\n",
2931 ring_data->dev->name);
2934 if (ring_data->rxd_mode == RXD_MODE_1) {
2935 rxdp1 = (struct RxD1 *)rxdp;
2936 pci_unmap_single(ring_data->pdev, (dma_addr_t)
2939 HEADER_ETHERNET_II_802_3_SIZE +
2942 PCI_DMA_FROMDEVICE);
2943 } else if (ring_data->rxd_mode == RXD_MODE_3B) {
2944 rxdp3 = (struct RxD3 *)rxdp;
2945 pci_dma_sync_single_for_cpu(ring_data->pdev,
2946 (dma_addr_t)rxdp3->Buffer0_ptr,
2948 PCI_DMA_FROMDEVICE);
2949 pci_unmap_single(ring_data->pdev,
2950 (dma_addr_t)rxdp3->Buffer2_ptr,
2952 PCI_DMA_FROMDEVICE);
2954 prefetch(skb->data);
2955 rx_osm_handler(ring_data, rxdp);
2957 ring_data->rx_curr_get_info.offset = get_info.offset;
2958 rxdp = ring_data->rx_blocks[get_block].
2959 rxds[get_info.offset].virt_addr;
2960 if (get_info.offset == rxd_count[ring_data->rxd_mode]) {
2961 get_info.offset = 0;
2962 ring_data->rx_curr_get_info.offset = get_info.offset;
2964 if (get_block == ring_data->block_count)
2966 ring_data->rx_curr_get_info.block_index = get_block;
2967 rxdp = ring_data->rx_blocks[get_block].block_virt_addr;
2970 if (ring_data->nic->config.napi) {
2977 if ((indicate_max_pkts) && (pkt_cnt > indicate_max_pkts))
2980 if (ring_data->lro) {
2981 /* Clear all LRO sessions before exiting */
2982 for (i = 0; i < MAX_LRO_SESSIONS; i++) {
2983 struct lro *lro = &ring_data->lro0_n[i];
2985 update_L3L4_header(ring_data->nic, lro);
2986 queue_rx_frame(lro->parent, lro->vlan_tag);
2987 clear_lro_session(lro);
2995 * tx_intr_handler - Transmit interrupt handler
2996 * @nic : device private variable
2998 * If an interrupt was raised to indicate DMA complete of the
2999 * Tx packet, this function is called. It identifies the last TxD
3000 * whose buffer was freed and frees all skbs whose data have already
3001 * DMA'ed into the NICs internal memory.
3006 static void tx_intr_handler(struct fifo_info *fifo_data)
3008 struct s2io_nic *nic = fifo_data->nic;
3009 struct tx_curr_get_info get_info, put_info;
3010 struct sk_buff *skb = NULL;
3013 unsigned long flags = 0;
3015 struct stat_block *stats = nic->mac_control.stats_info;
3016 struct swStat *swstats = &stats->sw_stat;
3018 if (!spin_trylock_irqsave(&fifo_data->tx_lock, flags))
3021 get_info = fifo_data->tx_curr_get_info;
3022 memcpy(&put_info, &fifo_data->tx_curr_put_info, sizeof(put_info));
3023 txdlp = fifo_data->list_info[get_info.offset].list_virt_addr;
3024 while ((!(txdlp->Control_1 & TXD_LIST_OWN_XENA)) &&
3025 (get_info.offset != put_info.offset) &&
3026 (txdlp->Host_Control)) {
3027 /* Check for TxD errors */
3028 if (txdlp->Control_1 & TXD_T_CODE) {
3029 unsigned long long err;
3030 err = txdlp->Control_1 & TXD_T_CODE;
3032 swstats->parity_err_cnt++;
3035 /* update t_code statistics */
3036 err_mask = err >> 48;
3039 swstats->tx_buf_abort_cnt++;
3043 swstats->tx_desc_abort_cnt++;
3047 swstats->tx_parity_err_cnt++;
3051 swstats->tx_link_loss_cnt++;
3055 swstats->tx_list_proc_err_cnt++;
3060 skb = s2io_txdl_getskb(fifo_data, txdlp, get_info.offset);
3062 spin_unlock_irqrestore(&fifo_data->tx_lock, flags);
3063 DBG_PRINT(ERR_DBG, "%s: NULL skb in Tx Free Intr\n",
3069 /* Updating the statistics block */
3070 swstats->mem_freed += skb->truesize;
3071 dev_kfree_skb_irq(skb);
3074 if (get_info.offset == get_info.fifo_len + 1)
3075 get_info.offset = 0;
3076 txdlp = fifo_data->list_info[get_info.offset].list_virt_addr;
3077 fifo_data->tx_curr_get_info.offset = get_info.offset;
3080 s2io_wake_tx_queue(fifo_data, pkt_cnt, nic->config.multiq);
3082 spin_unlock_irqrestore(&fifo_data->tx_lock, flags);
3086 * s2io_mdio_write - Function to write in to MDIO registers
3087 * @mmd_type : MMD type value (PMA/PMD/WIS/PCS/PHYXS)
3088 * @addr : address value
3089 * @value : data value
3090 * @dev : pointer to net_device structure
3092 * This function is used to write values to the MDIO registers
3095 static void s2io_mdio_write(u32 mmd_type, u64 addr, u16 value,
3096 struct net_device *dev)
3099 struct s2io_nic *sp = netdev_priv(dev);
3100 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3102 /* address transaction */
3103 val64 = MDIO_MMD_INDX_ADDR(addr) |
3104 MDIO_MMD_DEV_ADDR(mmd_type) |
3105 MDIO_MMS_PRT_ADDR(0x0);
3106 writeq(val64, &bar0->mdio_control);
3107 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3108 writeq(val64, &bar0->mdio_control);
3111 /* Data transaction */
3112 val64 = MDIO_MMD_INDX_ADDR(addr) |
3113 MDIO_MMD_DEV_ADDR(mmd_type) |
3114 MDIO_MMS_PRT_ADDR(0x0) |
3115 MDIO_MDIO_DATA(value) |
3116 MDIO_OP(MDIO_OP_WRITE_TRANS);
3117 writeq(val64, &bar0->mdio_control);
3118 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3119 writeq(val64, &bar0->mdio_control);
3122 val64 = MDIO_MMD_INDX_ADDR(addr) |
3123 MDIO_MMD_DEV_ADDR(mmd_type) |
3124 MDIO_MMS_PRT_ADDR(0x0) |
3125 MDIO_OP(MDIO_OP_READ_TRANS);
3126 writeq(val64, &bar0->mdio_control);
3127 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3128 writeq(val64, &bar0->mdio_control);
3133 * s2io_mdio_read - Function to write in to MDIO registers
3134 * @mmd_type : MMD type value (PMA/PMD/WIS/PCS/PHYXS)
3135 * @addr : address value
3136 * @dev : pointer to net_device structure
3138 * This function is used to read values to the MDIO registers
3141 static u64 s2io_mdio_read(u32 mmd_type, u64 addr, struct net_device *dev)
3145 struct s2io_nic *sp = netdev_priv(dev);
3146 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3148 /* address transaction */
3149 val64 = val64 | (MDIO_MMD_INDX_ADDR(addr)
3150 | MDIO_MMD_DEV_ADDR(mmd_type)
3151 | MDIO_MMS_PRT_ADDR(0x0));
3152 writeq(val64, &bar0->mdio_control);
3153 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3154 writeq(val64, &bar0->mdio_control);
3157 /* Data transaction */
3158 val64 = MDIO_MMD_INDX_ADDR(addr) |
3159 MDIO_MMD_DEV_ADDR(mmd_type) |
3160 MDIO_MMS_PRT_ADDR(0x0) |
3161 MDIO_OP(MDIO_OP_READ_TRANS);
3162 writeq(val64, &bar0->mdio_control);
3163 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3164 writeq(val64, &bar0->mdio_control);
3167 /* Read the value from regs */
3168 rval64 = readq(&bar0->mdio_control);
3169 rval64 = rval64 & 0xFFFF0000;
3170 rval64 = rval64 >> 16;
3175 * s2io_chk_xpak_counter - Function to check the status of the xpak counters
3176 * @counter : counter value to be updated
3177 * @flag : flag to indicate the status
3178 * @type : counter type
3180 * This function is to check the status of the xpak counters value
3184 static void s2io_chk_xpak_counter(u64 *counter, u64 * regs_stat, u32 index,
3190 for (i = 0; i < index; i++)
3194 *counter = *counter + 1;
3195 val64 = *regs_stat & mask;
3196 val64 = val64 >> (index * 0x2);
3202 "Take Xframe NIC out of service.\n");
3204 "Excessive temperatures may result in premature transceiver failure.\n");
3208 "Take Xframe NIC out of service.\n");
3210 "Excessive bias currents may indicate imminent laser diode failure.\n");
3214 "Take Xframe NIC out of service.\n");
3216 "Excessive laser output power may saturate far-end receiver.\n");
3220 "Incorrect XPAK Alarm type\n");
3224 val64 = val64 << (index * 0x2);
3225 *regs_stat = (*regs_stat & (~mask)) | (val64);
3228 *regs_stat = *regs_stat & (~mask);
3233 * s2io_updt_xpak_counter - Function to update the xpak counters
3234 * @dev : pointer to net_device struct
3236 * This function is to upate the status of the xpak counters value
3239 static void s2io_updt_xpak_counter(struct net_device *dev)
3247 struct s2io_nic *sp = netdev_priv(dev);
3248 struct stat_block *stats = sp->mac_control.stats_info;
3249 struct xpakStat *xstats = &stats->xpak_stat;
3251 /* Check the communication with the MDIO slave */
3254 val64 = s2io_mdio_read(MDIO_MMD_PMAPMD, addr, dev);
3255 if ((val64 == 0xFFFF) || (val64 == 0x0000)) {
3257 "ERR: MDIO slave access failed - Returned %llx\n",
3258 (unsigned long long)val64);
3262 /* Check for the expected value of control reg 1 */
3263 if (val64 != MDIO_CTRL1_SPEED10G) {
3264 DBG_PRINT(ERR_DBG, "Incorrect value at PMA address 0x0000 - "
3265 "Returned: %llx- Expected: 0x%x\n",
3266 (unsigned long long)val64, MDIO_CTRL1_SPEED10G);
3270 /* Loading the DOM register to MDIO register */
3272 s2io_mdio_write(MDIO_MMD_PMAPMD, addr, val16, dev);
3273 val64 = s2io_mdio_read(MDIO_MMD_PMAPMD, addr, dev);
3275 /* Reading the Alarm flags */
3278 val64 = s2io_mdio_read(MDIO_MMD_PMAPMD, addr, dev);
3280 flag = CHECKBIT(val64, 0x7);
3282 s2io_chk_xpak_counter(&xstats->alarm_transceiver_temp_high,
3283 &xstats->xpak_regs_stat,
3286 if (CHECKBIT(val64, 0x6))
3287 xstats->alarm_transceiver_temp_low++;
3289 flag = CHECKBIT(val64, 0x3);
3291 s2io_chk_xpak_counter(&xstats->alarm_laser_bias_current_high,
3292 &xstats->xpak_regs_stat,
3295 if (CHECKBIT(val64, 0x2))
3296 xstats->alarm_laser_bias_current_low++;
3298 flag = CHECKBIT(val64, 0x1);
3300 s2io_chk_xpak_counter(&xstats->alarm_laser_output_power_high,
3301 &xstats->xpak_regs_stat,
3304 if (CHECKBIT(val64, 0x0))
3305 xstats->alarm_laser_output_power_low++;
3307 /* Reading the Warning flags */
3310 val64 = s2io_mdio_read(MDIO_MMD_PMAPMD, addr, dev);
3312 if (CHECKBIT(val64, 0x7))
3313 xstats->warn_transceiver_temp_high++;
3315 if (CHECKBIT(val64, 0x6))
3316 xstats->warn_transceiver_temp_low++;
3318 if (CHECKBIT(val64, 0x3))
3319 xstats->warn_laser_bias_current_high++;
3321 if (CHECKBIT(val64, 0x2))
3322 xstats->warn_laser_bias_current_low++;
3324 if (CHECKBIT(val64, 0x1))
3325 xstats->warn_laser_output_power_high++;
3327 if (CHECKBIT(val64, 0x0))
3328 xstats->warn_laser_output_power_low++;
3332 * wait_for_cmd_complete - waits for a command to complete.
3333 * @sp : private member of the device structure, which is a pointer to the
3334 * s2io_nic structure.
3335 * Description: Function that waits for a command to Write into RMAC
3336 * ADDR DATA registers to be completed and returns either success or
3337 * error depending on whether the command was complete or not.
3339 * SUCCESS on success and FAILURE on failure.
3342 static int wait_for_cmd_complete(void __iomem *addr, u64 busy_bit,
3345 int ret = FAILURE, cnt = 0, delay = 1;
3348 if ((bit_state != S2IO_BIT_RESET) && (bit_state != S2IO_BIT_SET))
3352 val64 = readq(addr);
3353 if (bit_state == S2IO_BIT_RESET) {
3354 if (!(val64 & busy_bit)) {
3359 if (val64 & busy_bit) {
3376 * check_pci_device_id - Checks if the device id is supported
3378 * Description: Function to check if the pci device id is supported by driver.
3379 * Return value: Actual device id if supported else PCI_ANY_ID
3381 static u16 check_pci_device_id(u16 id)
3384 case PCI_DEVICE_ID_HERC_WIN:
3385 case PCI_DEVICE_ID_HERC_UNI:
3386 return XFRAME_II_DEVICE;
3387 case PCI_DEVICE_ID_S2IO_UNI:
3388 case PCI_DEVICE_ID_S2IO_WIN:
3389 return XFRAME_I_DEVICE;
3396 * s2io_reset - Resets the card.
3397 * @sp : private member of the device structure.
3398 * Description: Function to Reset the card. This function then also
3399 * restores the previously saved PCI configuration space registers as
3400 * the card reset also resets the configuration space.
3405 static void s2io_reset(struct s2io_nic *sp)
3407 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3412 unsigned long long up_cnt, down_cnt, up_time, down_time, reset_cnt;
3413 unsigned long long mem_alloc_cnt, mem_free_cnt, watchdog_cnt;
3414 struct stat_block *stats;
3415 struct swStat *swstats;
3417 DBG_PRINT(INIT_DBG, "%s: Resetting XFrame card %s\n",
3418 __func__, pci_name(sp->pdev));
3420 /* Back up the PCI-X CMD reg, dont want to lose MMRBC, OST settings */
3421 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, &(pci_cmd));
3423 val64 = SW_RESET_ALL;
3424 writeq(val64, &bar0->sw_reset);
3425 if (strstr(sp->product_name, "CX4"))
3428 for (i = 0; i < S2IO_MAX_PCI_CONFIG_SPACE_REINIT; i++) {
3430 /* Restore the PCI state saved during initialization. */
3431 pci_restore_state(sp->pdev);
3432 pci_save_state(sp->pdev);
3433 pci_read_config_word(sp->pdev, 0x2, &val16);
3434 if (check_pci_device_id(val16) != (u16)PCI_ANY_ID)
3439 if (check_pci_device_id(val16) == (u16)PCI_ANY_ID)
3440 DBG_PRINT(ERR_DBG, "%s SW_Reset failed!\n", __func__);
3442 pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, pci_cmd);
3446 /* Set swapper to enable I/O register access */
3447 s2io_set_swapper(sp);
3449 /* restore mac_addr entries */
3450 do_s2io_restore_unicast_mc(sp);
3452 /* Restore the MSIX table entries from local variables */
3453 restore_xmsi_data(sp);
3455 /* Clear certain PCI/PCI-X fields after reset */
3456 if (sp->device_type == XFRAME_II_DEVICE) {
3457 /* Clear "detected parity error" bit */
3458 pci_write_config_word(sp->pdev, PCI_STATUS, 0x8000);
3460 /* Clearing PCIX Ecc status register */
3461 pci_write_config_dword(sp->pdev, 0x68, 0x7C);
3463 /* Clearing PCI_STATUS error reflected here */
3464 writeq(s2BIT(62), &bar0->txpic_int_reg);
3467 /* Reset device statistics maintained by OS */
3468 memset(&sp->stats, 0, sizeof(struct net_device_stats));
3470 stats = sp->mac_control.stats_info;
3471 swstats = &stats->sw_stat;
3473 /* save link up/down time/cnt, reset/memory/watchdog cnt */
3474 up_cnt = swstats->link_up_cnt;
3475 down_cnt = swstats->link_down_cnt;
3476 up_time = swstats->link_up_time;
3477 down_time = swstats->link_down_time;
3478 reset_cnt = swstats->soft_reset_cnt;
3479 mem_alloc_cnt = swstats->mem_allocated;
3480 mem_free_cnt = swstats->mem_freed;
3481 watchdog_cnt = swstats->watchdog_timer_cnt;
3483 memset(stats, 0, sizeof(struct stat_block));
3485 /* restore link up/down time/cnt, reset/memory/watchdog cnt */
3486 swstats->link_up_cnt = up_cnt;
3487 swstats->link_down_cnt = down_cnt;
3488 swstats->link_up_time = up_time;
3489 swstats->link_down_time = down_time;
3490 swstats->soft_reset_cnt = reset_cnt;
3491 swstats->mem_allocated = mem_alloc_cnt;
3492 swstats->mem_freed = mem_free_cnt;
3493 swstats->watchdog_timer_cnt = watchdog_cnt;
3495 /* SXE-002: Configure link and activity LED to turn it off */
3496 subid = sp->pdev->subsystem_device;
3497 if (((subid & 0xFF) >= 0x07) &&
3498 (sp->device_type == XFRAME_I_DEVICE)) {
3499 val64 = readq(&bar0->gpio_control);
3500 val64 |= 0x0000800000000000ULL;
3501 writeq(val64, &bar0->gpio_control);
3502 val64 = 0x0411040400000000ULL;
3503 writeq(val64, (void __iomem *)bar0 + 0x2700);
3507 * Clear spurious ECC interrupts that would have occurred on
3508 * XFRAME II cards after reset.
3510 if (sp->device_type == XFRAME_II_DEVICE) {
3511 val64 = readq(&bar0->pcc_err_reg);
3512 writeq(val64, &bar0->pcc_err_reg);
3515 sp->device_enabled_once = false;
3519 * s2io_set_swapper - to set the swapper controle on the card
3520 * @sp : private member of the device structure,
3521 * pointer to the s2io_nic structure.
3522 * Description: Function to set the swapper control on the card
3523 * correctly depending on the 'endianness' of the system.
3525 * SUCCESS on success and FAILURE on failure.
3528 static int s2io_set_swapper(struct s2io_nic *sp)
3530 struct net_device *dev = sp->dev;
3531 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3532 u64 val64, valt, valr;
3535 * Set proper endian settings and verify the same by reading
3536 * the PIF Feed-back register.
3539 val64 = readq(&bar0->pif_rd_swapper_fb);
3540 if (val64 != 0x0123456789ABCDEFULL) {
3542 static const u64 value[] = {
3543 0xC30000C3C30000C3ULL, /* FE=1, SE=1 */
3544 0x8100008181000081ULL, /* FE=1, SE=0 */
3545 0x4200004242000042ULL, /* FE=0, SE=1 */
3550 writeq(value[i], &bar0->swapper_ctrl);
3551 val64 = readq(&bar0->pif_rd_swapper_fb);
3552 if (val64 == 0x0123456789ABCDEFULL)
3557 DBG_PRINT(ERR_DBG, "%s: Endian settings are wrong, "
3558 "feedback read %llx\n",
3559 dev->name, (unsigned long long)val64);
3564 valr = readq(&bar0->swapper_ctrl);
3567 valt = 0x0123456789ABCDEFULL;
3568 writeq(valt, &bar0->xmsi_address);
3569 val64 = readq(&bar0->xmsi_address);
3571 if (val64 != valt) {
3573 static const u64 value[] = {
3574 0x00C3C30000C3C300ULL, /* FE=1, SE=1 */
3575 0x0081810000818100ULL, /* FE=1, SE=0 */
3576 0x0042420000424200ULL, /* FE=0, SE=1 */
3581 writeq((value[i] | valr), &bar0->swapper_ctrl);
3582 writeq(valt, &bar0->xmsi_address);
3583 val64 = readq(&bar0->xmsi_address);
3589 unsigned long long x = val64;
3591 "Write failed, Xmsi_addr reads:0x%llx\n", x);
3595 val64 = readq(&bar0->swapper_ctrl);
3596 val64 &= 0xFFFF000000000000ULL;
3600 * The device by default set to a big endian format, so a
3601 * big endian driver need not set anything.
3603 val64 |= (SWAPPER_CTRL_TXP_FE |
3604 SWAPPER_CTRL_TXP_SE |
3605 SWAPPER_CTRL_TXD_R_FE |
3606 SWAPPER_CTRL_TXD_W_FE |
3607 SWAPPER_CTRL_TXF_R_FE |
3608 SWAPPER_CTRL_RXD_R_FE |
3609 SWAPPER_CTRL_RXD_W_FE |
3610 SWAPPER_CTRL_RXF_W_FE |
3611 SWAPPER_CTRL_XMSI_FE |
3612 SWAPPER_CTRL_STATS_FE |
3613 SWAPPER_CTRL_STATS_SE);
3614 if (sp->config.intr_type == INTA)
3615 val64 |= SWAPPER_CTRL_XMSI_SE;
3616 writeq(val64, &bar0->swapper_ctrl);
3619 * Initially we enable all bits to make it accessible by the
3620 * driver, then we selectively enable only those bits that
3623 val64 |= (SWAPPER_CTRL_TXP_FE |
3624 SWAPPER_CTRL_TXP_SE |
3625 SWAPPER_CTRL_TXD_R_FE |
3626 SWAPPER_CTRL_TXD_R_SE |
3627 SWAPPER_CTRL_TXD_W_FE |
3628 SWAPPER_CTRL_TXD_W_SE |
3629 SWAPPER_CTRL_TXF_R_FE |
3630 SWAPPER_CTRL_RXD_R_FE |
3631 SWAPPER_CTRL_RXD_R_SE |
3632 SWAPPER_CTRL_RXD_W_FE |
3633 SWAPPER_CTRL_RXD_W_SE |
3634 SWAPPER_CTRL_RXF_W_FE |
3635 SWAPPER_CTRL_XMSI_FE |
3636 SWAPPER_CTRL_STATS_FE |
3637 SWAPPER_CTRL_STATS_SE);
3638 if (sp->config.intr_type == INTA)
3639 val64 |= SWAPPER_CTRL_XMSI_SE;
3640 writeq(val64, &bar0->swapper_ctrl);
3642 val64 = readq(&bar0->swapper_ctrl);
3645 * Verifying if endian settings are accurate by reading a
3646 * feedback register.
3648 val64 = readq(&bar0->pif_rd_swapper_fb);
3649 if (val64 != 0x0123456789ABCDEFULL) {
3650 /* Endian settings are incorrect, calls for another dekko. */
3652 "%s: Endian settings are wrong, feedback read %llx\n",
3653 dev->name, (unsigned long long)val64);
3660 static int wait_for_msix_trans(struct s2io_nic *nic, int i)
3662 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3664 int ret = 0, cnt = 0;
3667 val64 = readq(&bar0->xmsi_access);
3668 if (!(val64 & s2BIT(15)))
3674 DBG_PRINT(ERR_DBG, "XMSI # %d Access failed\n", i);
3681 static void restore_xmsi_data(struct s2io_nic *nic)
3683 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3687 if (nic->device_type == XFRAME_I_DEVICE)
3690 for (i = 0; i < MAX_REQUESTED_MSI_X; i++) {
3691 msix_index = (i) ? ((i-1) * 8 + 1) : 0;
3692 writeq(nic->msix_info[i].addr, &bar0->xmsi_address);
3693 writeq(nic->msix_info[i].data, &bar0->xmsi_data);
3694 val64 = (s2BIT(7) | s2BIT(15) | vBIT(msix_index, 26, 6));
3695 writeq(val64, &bar0->xmsi_access);
3696 if (wait_for_msix_trans(nic, msix_index)) {
3697 DBG_PRINT(ERR_DBG, "%s: index: %d failed\n",
3698 __func__, msix_index);
3704 static void store_xmsi_data(struct s2io_nic *nic)
3706 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3707 u64 val64, addr, data;
3710 if (nic->device_type == XFRAME_I_DEVICE)
3713 /* Store and display */
3714 for (i = 0; i < MAX_REQUESTED_MSI_X; i++) {
3715 msix_index = (i) ? ((i-1) * 8 + 1) : 0;
3716 val64 = (s2BIT(15) | vBIT(msix_index, 26, 6));
3717 writeq(val64, &bar0->xmsi_access);
3718 if (wait_for_msix_trans(nic, msix_index)) {
3719 DBG_PRINT(ERR_DBG, "%s: index: %d failed\n",
3720 __func__, msix_index);
3723 addr = readq(&bar0->xmsi_address);
3724 data = readq(&bar0->xmsi_data);
3726 nic->msix_info[i].addr = addr;
3727 nic->msix_info[i].data = data;
3732 static int s2io_enable_msi_x(struct s2io_nic *nic)
3734 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3736 u16 msi_control; /* Temp variable */
3737 int ret, i, j, msix_indx = 1;
3739 struct stat_block *stats = nic->mac_control.stats_info;
3740 struct swStat *swstats = &stats->sw_stat;
3742 size = nic->num_entries * sizeof(struct msix_entry);
3743 nic->entries = kzalloc(size, GFP_KERNEL);
3744 if (!nic->entries) {
3745 DBG_PRINT(INFO_DBG, "%s: Memory allocation failed\n",
3747 swstats->mem_alloc_fail_cnt++;
3750 swstats->mem_allocated += size;
3752 size = nic->num_entries * sizeof(struct s2io_msix_entry);
3753 nic->s2io_entries = kzalloc(size, GFP_KERNEL);
3754 if (!nic->s2io_entries) {
3755 DBG_PRINT(INFO_DBG, "%s: Memory allocation failed\n",
3757 swstats->mem_alloc_fail_cnt++;
3758 kfree(nic->entries);
3760 += (nic->num_entries * sizeof(struct msix_entry));
3763 swstats->mem_allocated += size;
3765 nic->entries[0].entry = 0;
3766 nic->s2io_entries[0].entry = 0;
3767 nic->s2io_entries[0].in_use = MSIX_FLG;
3768 nic->s2io_entries[0].type = MSIX_ALARM_TYPE;
3769 nic->s2io_entries[0].arg = &nic->mac_control.fifos;
3771 for (i = 1; i < nic->num_entries; i++) {
3772 nic->entries[i].entry = ((i - 1) * 8) + 1;
3773 nic->s2io_entries[i].entry = ((i - 1) * 8) + 1;
3774 nic->s2io_entries[i].arg = NULL;
3775 nic->s2io_entries[i].in_use = 0;
3778 rx_mat = readq(&bar0->rx_mat);
3779 for (j = 0; j < nic->config.rx_ring_num; j++) {
3780 rx_mat |= RX_MAT_SET(j, msix_indx);
3781 nic->s2io_entries[j+1].arg = &nic->mac_control.rings[j];
3782 nic->s2io_entries[j+1].type = MSIX_RING_TYPE;
3783 nic->s2io_entries[j+1].in_use = MSIX_FLG;
3786 writeq(rx_mat, &bar0->rx_mat);
3787 readq(&bar0->rx_mat);
3789 ret = pci_enable_msix_range(nic->pdev, nic->entries,
3790 nic->num_entries, nic->num_entries);
3791 /* We fail init if error or we get less vectors than min required */
3793 DBG_PRINT(ERR_DBG, "Enabling MSI-X failed\n");
3794 kfree(nic->entries);
3795 swstats->mem_freed += nic->num_entries *
3796 sizeof(struct msix_entry);
3797 kfree(nic->s2io_entries);
3798 swstats->mem_freed += nic->num_entries *
3799 sizeof(struct s2io_msix_entry);
3800 nic->entries = NULL;
3801 nic->s2io_entries = NULL;
3806 * To enable MSI-X, MSI also needs to be enabled, due to a bug
3807 * in the herc NIC. (Temp change, needs to be removed later)
3809 pci_read_config_word(nic->pdev, 0x42, &msi_control);
3810 msi_control |= 0x1; /* Enable MSI */
3811 pci_write_config_word(nic->pdev, 0x42, msi_control);
3816 /* Handle software interrupt used during MSI(X) test */
3817 static irqreturn_t s2io_test_intr(int irq, void *dev_id)
3819 struct s2io_nic *sp = dev_id;
3821 sp->msi_detected = 1;
3822 wake_up(&sp->msi_wait);
3827 /* Test interrupt path by forcing a a software IRQ */
3828 static int s2io_test_msi(struct s2io_nic *sp)
3830 struct pci_dev *pdev = sp->pdev;
3831 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3835 err = request_irq(sp->entries[1].vector, s2io_test_intr, 0,
3838 DBG_PRINT(ERR_DBG, "%s: PCI %s: cannot assign irq %d\n",
3839 sp->dev->name, pci_name(pdev), pdev->irq);
3843 init_waitqueue_head(&sp->msi_wait);
3844 sp->msi_detected = 0;
3846 saved64 = val64 = readq(&bar0->scheduled_int_ctrl);
3847 val64 |= SCHED_INT_CTRL_ONE_SHOT;
3848 val64 |= SCHED_INT_CTRL_TIMER_EN;
3849 val64 |= SCHED_INT_CTRL_INT2MSI(1);
3850 writeq(val64, &bar0->scheduled_int_ctrl);
3852 wait_event_timeout(sp->msi_wait, sp->msi_detected, HZ/10);
3854 if (!sp->msi_detected) {
3855 /* MSI(X) test failed, go back to INTx mode */
3856 DBG_PRINT(ERR_DBG, "%s: PCI %s: No interrupt was generated "
3857 "using MSI(X) during test\n",
3858 sp->dev->name, pci_name(pdev));
3863 free_irq(sp->entries[1].vector, sp);
3865 writeq(saved64, &bar0->scheduled_int_ctrl);
3870 static void remove_msix_isr(struct s2io_nic *sp)
3875 for (i = 0; i < sp->num_entries; i++) {
3876 if (sp->s2io_entries[i].in_use == MSIX_REGISTERED_SUCCESS) {
3877 int vector = sp->entries[i].vector;
3878 void *arg = sp->s2io_entries[i].arg;
3879 free_irq(vector, arg);
3884 kfree(sp->s2io_entries);
3886 sp->s2io_entries = NULL;
3888 pci_read_config_word(sp->pdev, 0x42, &msi_control);
3889 msi_control &= 0xFFFE; /* Disable MSI */
3890 pci_write_config_word(sp->pdev, 0x42, msi_control);
3892 pci_disable_msix(sp->pdev);
3895 static void remove_inta_isr(struct s2io_nic *sp)
3897 free_irq(sp->pdev->irq, sp->dev);
3900 /* ********************************************************* *
3901 * Functions defined below concern the OS part of the driver *
3902 * ********************************************************* */
3905 * s2io_open - open entry point of the driver
3906 * @dev : pointer to the device structure.
3908 * This function is the open entry point of the driver. It mainly calls a
3909 * function to allocate Rx buffers and inserts them into the buffer
3910 * descriptors and then enables the Rx part of the NIC.
3912 * 0 on success and an appropriate (-)ve integer as defined in errno.h
3916 static int s2io_open(struct net_device *dev)
3918 struct s2io_nic *sp = netdev_priv(dev);
3919 struct swStat *swstats = &sp->mac_control.stats_info->sw_stat;
3923 * Make sure you have link off by default every time
3924 * Nic is initialized
3926 netif_carrier_off(dev);
3927 sp->last_link_state = 0;
3929 /* Initialize H/W and enable interrupts */
3930 err = s2io_card_up(sp);
3932 DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
3934 goto hw_init_failed;
3937 if (do_s2io_prog_unicast(dev, dev->dev_addr) == FAILURE) {
3938 DBG_PRINT(ERR_DBG, "Set Mac Address Failed\n");
3941 goto hw_init_failed;
3943 s2io_start_all_tx_queue(sp);
3947 if (sp->config.intr_type == MSI_X) {
3950 swstats->mem_freed += sp->num_entries *
3951 sizeof(struct msix_entry);
3953 if (sp->s2io_entries) {
3954 kfree(sp->s2io_entries);
3955 swstats->mem_freed += sp->num_entries *
3956 sizeof(struct s2io_msix_entry);
3963 * s2io_close -close entry point of the driver
3964 * @dev : device pointer.
3966 * This is the stop entry point of the driver. It needs to undo exactly
3967 * whatever was done by the open entry point,thus it's usually referred to
3968 * as the close function.Among other things this function mainly stops the
3969 * Rx side of the NIC and frees all the Rx buffers in the Rx rings.
3971 * 0 on success and an appropriate (-)ve integer as defined in errno.h
3975 static int s2io_close(struct net_device *dev)
3977 struct s2io_nic *sp = netdev_priv(dev);
3978 struct config_param *config = &sp->config;
3982 /* Return if the device is already closed *
3983 * Can happen when s2io_card_up failed in change_mtu *
3985 if (!is_s2io_card_up(sp))
3988 s2io_stop_all_tx_queue(sp);
3989 /* delete all populated mac entries */
3990 for (offset = 1; offset < config->max_mc_addr; offset++) {
3991 tmp64 = do_s2io_read_unicast_mc(sp, offset);
3992 if (tmp64 != S2IO_DISABLE_MAC_ENTRY)
3993 do_s2io_delete_unicast_mc(sp, tmp64);
4002 * s2io_xmit - Tx entry point of te driver
4003 * @skb : the socket buffer containing the Tx data.
4004 * @dev : device pointer.
4006 * This function is the Tx entry point of the driver. S2IO NIC supports
4007 * certain protocol assist features on Tx side, namely CSO, S/G, LSO.
4008 * NOTE: when device can't queue the pkt,just the trans_start variable will
4011 * 0 on success & 1 on failure.
4014 static netdev_tx_t s2io_xmit(struct sk_buff *skb, struct net_device *dev)
4016 struct s2io_nic *sp = netdev_priv(dev);
4017 u16 frg_cnt, frg_len, i, queue, queue_len, put_off, get_off;
4020 struct TxFIFO_element __iomem *tx_fifo;
4021 unsigned long flags = 0;
4023 struct fifo_info *fifo = NULL;
4024 int do_spin_lock = 1;
4026 int enable_per_list_interrupt = 0;
4027 struct config_param *config = &sp->config;
4028 struct mac_info *mac_control = &sp->mac_control;
4029 struct stat_block *stats = mac_control->stats_info;
4030 struct swStat *swstats = &stats->sw_stat;
4032 DBG_PRINT(TX_DBG, "%s: In Neterion Tx routine\n", dev->name);
4034 if (unlikely(skb->len <= 0)) {
4035 DBG_PRINT(TX_DBG, "%s: Buffer has no data..\n", dev->name);
4036 dev_kfree_skb_any(skb);
4037 return NETDEV_TX_OK;
4040 if (!is_s2io_card_up(sp)) {
4041 DBG_PRINT(TX_DBG, "%s: Card going down for reset\n",
4043 dev_kfree_skb_any(skb);
4044 return NETDEV_TX_OK;
4048 if (vlan_tx_tag_present(skb))
4049 vlan_tag = vlan_tx_tag_get(skb);
4050 if (sp->config.tx_steering_type == TX_DEFAULT_STEERING) {
4051 if (skb->protocol == htons(ETH_P_IP)) {
4056 if (!ip_is_fragment(ip)) {
4057 th = (struct tcphdr *)(((unsigned char *)ip) +
4060 if (ip->protocol == IPPROTO_TCP) {
4061 queue_len = sp->total_tcp_fifos;
4062 queue = (ntohs(th->source) +
4064 sp->fifo_selector[queue_len - 1];
4065 if (queue >= queue_len)
4066 queue = queue_len - 1;
4067 } else if (ip->protocol == IPPROTO_UDP) {
4068 queue_len = sp->total_udp_fifos;
4069 queue = (ntohs(th->source) +
4071 sp->fifo_selector[queue_len - 1];
4072 if (queue >= queue_len)
4073 queue = queue_len - 1;
4074 queue += sp->udp_fifo_idx;
4075 if (skb->len > 1024)
4076 enable_per_list_interrupt = 1;
4081 } else if (sp->config.tx_steering_type == TX_PRIORITY_STEERING)
4082 /* get fifo number based on skb->priority value */
4083 queue = config->fifo_mapping
4084 [skb->priority & (MAX_TX_FIFOS - 1)];
4085 fifo = &mac_control->fifos[queue];
4088 spin_lock_irqsave(&fifo->tx_lock, flags);
4090 if (unlikely(!spin_trylock_irqsave(&fifo->tx_lock, flags)))
4091 return NETDEV_TX_LOCKED;
4094 if (sp->config.multiq) {
4095 if (__netif_subqueue_stopped(dev, fifo->fifo_no)) {
4096 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4097 return NETDEV_TX_BUSY;
4099 } else if (unlikely(fifo->queue_state == FIFO_QUEUE_STOP)) {
4100 if (netif_queue_stopped(dev)) {
4101 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4102 return NETDEV_TX_BUSY;
4106 put_off = (u16)fifo->tx_curr_put_info.offset;
4107 get_off = (u16)fifo->tx_curr_get_info.offset;
4108 txdp = fifo->list_info[put_off].list_virt_addr;
4110 queue_len = fifo->tx_curr_put_info.fifo_len + 1;
4111 /* Avoid "put" pointer going beyond "get" pointer */
4112 if (txdp->Host_Control ||
4113 ((put_off+1) == queue_len ? 0 : (put_off+1)) == get_off) {
4114 DBG_PRINT(TX_DBG, "Error in xmit, No free TXDs.\n");
4115 s2io_stop_tx_queue(sp, fifo->fifo_no);
4116 dev_kfree_skb_any(skb);
4117 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4118 return NETDEV_TX_OK;
4121 offload_type = s2io_offload_type(skb);
4122 if (offload_type & (SKB_GSO_TCPV4 | SKB_GSO_TCPV6)) {
4123 txdp->Control_1 |= TXD_TCP_LSO_EN;
4124 txdp->Control_1 |= TXD_TCP_LSO_MSS(s2io_tcp_mss(skb));
4126 if (skb->ip_summed == CHECKSUM_PARTIAL) {
4127 txdp->Control_2 |= (TXD_TX_CKO_IPV4_EN |
4131 txdp->Control_1 |= TXD_GATHER_CODE_FIRST;
4132 txdp->Control_1 |= TXD_LIST_OWN_XENA;
4133 txdp->Control_2 |= TXD_INT_NUMBER(fifo->fifo_no);
4134 if (enable_per_list_interrupt)
4135 if (put_off & (queue_len >> 5))
4136 txdp->Control_2 |= TXD_INT_TYPE_PER_LIST;
4138 txdp->Control_2 |= TXD_VLAN_ENABLE;
4139 txdp->Control_2 |= TXD_VLAN_TAG(vlan_tag);
4142 frg_len = skb_headlen(skb);
4143 if (offload_type == SKB_GSO_UDP) {
4146 ufo_size = s2io_udp_mss(skb);
4148 txdp->Control_1 |= TXD_UFO_EN;
4149 txdp->Control_1 |= TXD_UFO_MSS(ufo_size);
4150 txdp->Control_1 |= TXD_BUFFER0_SIZE(8);
4152 /* both variants do cpu_to_be64(be32_to_cpu(...)) */
4153 fifo->ufo_in_band_v[put_off] =
4154 (__force u64)skb_shinfo(skb)->ip6_frag_id;
4156 fifo->ufo_in_band_v[put_off] =
4157 (__force u64)skb_shinfo(skb)->ip6_frag_id << 32;
4159 txdp->Host_Control = (unsigned long)fifo->ufo_in_band_v;
4160 txdp->Buffer_Pointer = pci_map_single(sp->pdev,
4161 fifo->ufo_in_band_v,
4164 if (pci_dma_mapping_error(sp->pdev, txdp->Buffer_Pointer))
4165 goto pci_map_failed;
4169 txdp->Buffer_Pointer = pci_map_single(sp->pdev, skb->data,
4170 frg_len, PCI_DMA_TODEVICE);
4171 if (pci_dma_mapping_error(sp->pdev, txdp->Buffer_Pointer))
4172 goto pci_map_failed;
4174 txdp->Host_Control = (unsigned long)skb;
4175 txdp->Control_1 |= TXD_BUFFER0_SIZE(frg_len);
4176 if (offload_type == SKB_GSO_UDP)
4177 txdp->Control_1 |= TXD_UFO_EN;
4179 frg_cnt = skb_shinfo(skb)->nr_frags;
4180 /* For fragmented SKB. */
4181 for (i = 0; i < frg_cnt; i++) {
4182 const skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
4183 /* A '0' length fragment will be ignored */
4184 if (!skb_frag_size(frag))
4187 txdp->Buffer_Pointer = (u64)skb_frag_dma_map(&sp->pdev->dev,
4189 skb_frag_size(frag),
4191 txdp->Control_1 = TXD_BUFFER0_SIZE(skb_frag_size(frag));
4192 if (offload_type == SKB_GSO_UDP)
4193 txdp->Control_1 |= TXD_UFO_EN;
4195 txdp->Control_1 |= TXD_GATHER_CODE_LAST;
4197 if (offload_type == SKB_GSO_UDP)
4198 frg_cnt++; /* as Txd0 was used for inband header */
4200 tx_fifo = mac_control->tx_FIFO_start[queue];
4201 val64 = fifo->list_info[put_off].list_phy_addr;
4202 writeq(val64, &tx_fifo->TxDL_Pointer);
4204 val64 = (TX_FIFO_LAST_TXD_NUM(frg_cnt) | TX_FIFO_FIRST_LIST |
4207 val64 |= TX_FIFO_SPECIAL_FUNC;
4209 writeq(val64, &tx_fifo->List_Control);
4214 if (put_off == fifo->tx_curr_put_info.fifo_len + 1)
4216 fifo->tx_curr_put_info.offset = put_off;
4218 /* Avoid "put" pointer going beyond "get" pointer */
4219 if (((put_off+1) == queue_len ? 0 : (put_off+1)) == get_off) {
4220 swstats->fifo_full_cnt++;
4222 "No free TxDs for xmit, Put: 0x%x Get:0x%x\n",
4224 s2io_stop_tx_queue(sp, fifo->fifo_no);
4226 swstats->mem_allocated += skb->truesize;
4227 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4229 if (sp->config.intr_type == MSI_X)
4230 tx_intr_handler(fifo);
4232 return NETDEV_TX_OK;
4235 swstats->pci_map_fail_cnt++;
4236 s2io_stop_tx_queue(sp, fifo->fifo_no);
4237 swstats->mem_freed += skb->truesize;
4238 dev_kfree_skb_any(skb);
4239 spin_unlock_irqrestore(&fifo->tx_lock, flags);
4240 return NETDEV_TX_OK;
4244 s2io_alarm_handle(unsigned long data)
4246 struct s2io_nic *sp = (struct s2io_nic *)data;
4247 struct net_device *dev = sp->dev;
4249 s2io_handle_errors(dev);
4250 mod_timer(&sp->alarm_timer, jiffies + HZ / 2);
4253 static irqreturn_t s2io_msix_ring_handle(int irq, void *dev_id)
4255 struct ring_info *ring = (struct ring_info *)dev_id;
4256 struct s2io_nic *sp = ring->nic;
4257 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4259 if (unlikely(!is_s2io_card_up(sp)))
4262 if (sp->config.napi) {
4263 u8 __iomem *addr = NULL;
4266 addr = (u8 __iomem *)&bar0->xmsi_mask_reg;
4267 addr += (7 - ring->ring_no);
4268 val8 = (ring->ring_no == 0) ? 0x7f : 0xff;
4271 napi_schedule(&ring->napi);
4273 rx_intr_handler(ring, 0);
4274 s2io_chk_rx_buffers(sp, ring);
4280 static irqreturn_t s2io_msix_fifo_handle(int irq, void *dev_id)
4283 struct fifo_info *fifos = (struct fifo_info *)dev_id;
4284 struct s2io_nic *sp = fifos->nic;
4285 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4286 struct config_param *config = &sp->config;
4289 if (unlikely(!is_s2io_card_up(sp)))
4292 reason = readq(&bar0->general_int_status);
4293 if (unlikely(reason == S2IO_MINUS_ONE))
4294 /* Nothing much can be done. Get out */
4297 if (reason & (GEN_INTR_TXPIC | GEN_INTR_TXTRAFFIC)) {
4298 writeq(S2IO_MINUS_ONE, &bar0->general_int_mask);
4300 if (reason & GEN_INTR_TXPIC)
4301 s2io_txpic_intr_handle(sp);
4303 if (reason & GEN_INTR_TXTRAFFIC)
4304 writeq(S2IO_MINUS_ONE, &bar0->tx_traffic_int);
4306 for (i = 0; i < config->tx_fifo_num; i++)
4307 tx_intr_handler(&fifos[i]);
4309 writeq(sp->general_int_mask, &bar0->general_int_mask);
4310 readl(&bar0->general_int_status);
4313 /* The interrupt was not raised by us */
4317 static void s2io_txpic_intr_handle(struct s2io_nic *sp)
4319 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4322 val64 = readq(&bar0->pic_int_status);
4323 if (val64 & PIC_INT_GPIO) {
4324 val64 = readq(&bar0->gpio_int_reg);
4325 if ((val64 & GPIO_INT_REG_LINK_DOWN) &&
4326 (val64 & GPIO_INT_REG_LINK_UP)) {
4328 * This is unstable state so clear both up/down
4329 * interrupt and adapter to re-evaluate the link state.
4331 val64 |= GPIO_INT_REG_LINK_DOWN;
4332 val64 |= GPIO_INT_REG_LINK_UP;
4333 writeq(val64, &bar0->gpio_int_reg);
4334 val64 = readq(&bar0->gpio_int_mask);
4335 val64 &= ~(GPIO_INT_MASK_LINK_UP |
4336 GPIO_INT_MASK_LINK_DOWN);
4337 writeq(val64, &bar0->gpio_int_mask);
4338 } else if (val64 & GPIO_INT_REG_LINK_UP) {
4339 val64 = readq(&bar0->adapter_status);
4340 /* Enable Adapter */
4341 val64 = readq(&bar0->adapter_control);
4342 val64 |= ADAPTER_CNTL_EN;
4343 writeq(val64, &bar0->adapter_control);
4344 val64 |= ADAPTER_LED_ON;
4345 writeq(val64, &bar0->adapter_control);
4346 if (!sp->device_enabled_once)
4347 sp->device_enabled_once = 1;
4349 s2io_link(sp, LINK_UP);
4351 * unmask link down interrupt and mask link-up
4354 val64 = readq(&bar0->gpio_int_mask);
4355 val64 &= ~GPIO_INT_MASK_LINK_DOWN;
4356 val64 |= GPIO_INT_MASK_LINK_UP;
4357 writeq(val64, &bar0->gpio_int_mask);
4359 } else if (val64 & GPIO_INT_REG_LINK_DOWN) {
4360 val64 = readq(&bar0->adapter_status);
4361 s2io_link(sp, LINK_DOWN);
4362 /* Link is down so unmaks link up interrupt */
4363 val64 = readq(&bar0->gpio_int_mask);
4364 val64 &= ~GPIO_INT_MASK_LINK_UP;
4365 val64 |= GPIO_INT_MASK_LINK_DOWN;
4366 writeq(val64, &bar0->gpio_int_mask);
4369 val64 = readq(&bar0->adapter_control);
4370 val64 = val64 & (~ADAPTER_LED_ON);
4371 writeq(val64, &bar0->adapter_control);
4374 val64 = readq(&bar0->gpio_int_mask);
4378 * do_s2io_chk_alarm_bit - Check for alarm and incrment the counter
4379 * @value: alarm bits
4380 * @addr: address value
4381 * @cnt: counter variable
4382 * Description: Check for alarm and increment the counter
4384 * 1 - if alarm bit set
4385 * 0 - if alarm bit is not set
4387 static int do_s2io_chk_alarm_bit(u64 value, void __iomem *addr,
4388 unsigned long long *cnt)
4391 val64 = readq(addr);
4392 if (val64 & value) {
4393 writeq(val64, addr);
4402 * s2io_handle_errors - Xframe error indication handler
4403 * @nic: device private variable
4404 * Description: Handle alarms such as loss of link, single or
4405 * double ECC errors, critical and serious errors.
4409 static void s2io_handle_errors(void *dev_id)
4411 struct net_device *dev = (struct net_device *)dev_id;
4412 struct s2io_nic *sp = netdev_priv(dev);
4413 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4414 u64 temp64 = 0, val64 = 0;
4417 struct swStat *sw_stat = &sp->mac_control.stats_info->sw_stat;
4418 struct xpakStat *stats = &sp->mac_control.stats_info->xpak_stat;
4420 if (!is_s2io_card_up(sp))
4423 if (pci_channel_offline(sp->pdev))
4426 memset(&sw_stat->ring_full_cnt, 0,
4427 sizeof(sw_stat->ring_full_cnt));
4429 /* Handling the XPAK counters update */
4430 if (stats->xpak_timer_count < 72000) {
4431 /* waiting for an hour */
4432 stats->xpak_timer_count++;
4434 s2io_updt_xpak_counter(dev);
4435 /* reset the count to zero */
4436 stats->xpak_timer_count = 0;
4439 /* Handling link status change error Intr */
4440 if (s2io_link_fault_indication(sp) == MAC_RMAC_ERR_TIMER) {
4441 val64 = readq(&bar0->mac_rmac_err_reg);
4442 writeq(val64, &bar0->mac_rmac_err_reg);
4443 if (val64 & RMAC_LINK_STATE_CHANGE_INT)
4444 schedule_work(&sp->set_link_task);
4447 /* In case of a serious error, the device will be Reset. */
4448 if (do_s2io_chk_alarm_bit(SERR_SOURCE_ANY, &bar0->serr_source,
4449 &sw_stat->serious_err_cnt))
4452 /* Check for data parity error */
4453 if (do_s2io_chk_alarm_bit(GPIO_INT_REG_DP_ERR_INT, &bar0->gpio_int_reg,
4454 &sw_stat->parity_err_cnt))
4457 /* Check for ring full counter */
4458 if (sp->device_type == XFRAME_II_DEVICE) {
4459 val64 = readq(&bar0->ring_bump_counter1);
4460 for (i = 0; i < 4; i++) {
4461 temp64 = (val64 & vBIT(0xFFFF, (i*16), 16));
4462 temp64 >>= 64 - ((i+1)*16);
4463 sw_stat->ring_full_cnt[i] += temp64;
4466 val64 = readq(&bar0->ring_bump_counter2);
4467 for (i = 0; i < 4; i++) {
4468 temp64 = (val64 & vBIT(0xFFFF, (i*16), 16));
4469 temp64 >>= 64 - ((i+1)*16);
4470 sw_stat->ring_full_cnt[i+4] += temp64;
4474 val64 = readq(&bar0->txdma_int_status);
4475 /*check for pfc_err*/
4476 if (val64 & TXDMA_PFC_INT) {
4477 if (do_s2io_chk_alarm_bit(PFC_ECC_DB_ERR | PFC_SM_ERR_ALARM |
4478 PFC_MISC_0_ERR | PFC_MISC_1_ERR |
4481 &sw_stat->pfc_err_cnt))
4483 do_s2io_chk_alarm_bit(PFC_ECC_SG_ERR,
4485 &sw_stat->pfc_err_cnt);
4488 /*check for tda_err*/
4489 if (val64 & TXDMA_TDA_INT) {
4490 if (do_s2io_chk_alarm_bit(TDA_Fn_ECC_DB_ERR |
4494 &sw_stat->tda_err_cnt))
4496 do_s2io_chk_alarm_bit(TDA_Fn_ECC_SG_ERR | TDA_PCIX_ERR,
4498 &sw_stat->tda_err_cnt);
4500 /*check for pcc_err*/
4501 if (val64 & TXDMA_PCC_INT) {
4502 if (do_s2io_chk_alarm_bit(PCC_SM_ERR_ALARM | PCC_WR_ERR_ALARM |
4503 PCC_N_SERR | PCC_6_COF_OV_ERR |
4504 PCC_7_COF_OV_ERR | PCC_6_LSO_OV_ERR |
4505 PCC_7_LSO_OV_ERR | PCC_FB_ECC_DB_ERR |
4508 &sw_stat->pcc_err_cnt))
4510 do_s2io_chk_alarm_bit(PCC_FB_ECC_SG_ERR | PCC_TXB_ECC_SG_ERR,
4512 &sw_stat->pcc_err_cnt);
4515 /*check for tti_err*/
4516 if (val64 & TXDMA_TTI_INT) {
4517 if (do_s2io_chk_alarm_bit(TTI_SM_ERR_ALARM,
4519 &sw_stat->tti_err_cnt))
4521 do_s2io_chk_alarm_bit(TTI_ECC_SG_ERR | TTI_ECC_DB_ERR,
4523 &sw_stat->tti_err_cnt);
4526 /*check for lso_err*/
4527 if (val64 & TXDMA_LSO_INT) {
4528 if (do_s2io_chk_alarm_bit(LSO6_ABORT | LSO7_ABORT |
4529 LSO6_SM_ERR_ALARM | LSO7_SM_ERR_ALARM,
4531 &sw_stat->lso_err_cnt))
4533 do_s2io_chk_alarm_bit(LSO6_SEND_OFLOW | LSO7_SEND_OFLOW,
4535 &sw_stat->lso_err_cnt);
4538 /*check for tpa_err*/
4539 if (val64 & TXDMA_TPA_INT) {
4540 if (do_s2io_chk_alarm_bit(TPA_SM_ERR_ALARM,
4542 &sw_stat->tpa_err_cnt))
4544 do_s2io_chk_alarm_bit(TPA_TX_FRM_DROP,
4546 &sw_stat->tpa_err_cnt);
4549 /*check for sm_err*/
4550 if (val64 & TXDMA_SM_INT) {
4551 if (do_s2io_chk_alarm_bit(SM_SM_ERR_ALARM,
4553 &sw_stat->sm_err_cnt))
4557 val64 = readq(&bar0->mac_int_status);
4558 if (val64 & MAC_INT_STATUS_TMAC_INT) {
4559 if (do_s2io_chk_alarm_bit(TMAC_TX_BUF_OVRN | TMAC_TX_SM_ERR,
4560 &bar0->mac_tmac_err_reg,
4561 &sw_stat->mac_tmac_err_cnt))
4563 do_s2io_chk_alarm_bit(TMAC_ECC_SG_ERR | TMAC_ECC_DB_ERR |
4564 TMAC_DESC_ECC_SG_ERR |
4565 TMAC_DESC_ECC_DB_ERR,
4566 &bar0->mac_tmac_err_reg,
4567 &sw_stat->mac_tmac_err_cnt);
4570 val64 = readq(&bar0->xgxs_int_status);
4571 if (val64 & XGXS_INT_STATUS_TXGXS) {
4572 if (do_s2io_chk_alarm_bit(TXGXS_ESTORE_UFLOW | TXGXS_TX_SM_ERR,
4573 &bar0->xgxs_txgxs_err_reg,
4574 &sw_stat->xgxs_txgxs_err_cnt))
4576 do_s2io_chk_alarm_bit(TXGXS_ECC_SG_ERR | TXGXS_ECC_DB_ERR,
4577 &bar0->xgxs_txgxs_err_reg,
4578 &sw_stat->xgxs_txgxs_err_cnt);
4581 val64 = readq(&bar0->rxdma_int_status);
4582 if (val64 & RXDMA_INT_RC_INT_M) {
4583 if (do_s2io_chk_alarm_bit(RC_PRCn_ECC_DB_ERR |
4585 RC_PRCn_SM_ERR_ALARM |
4586 RC_FTC_SM_ERR_ALARM,
4588 &sw_stat->rc_err_cnt))
4590 do_s2io_chk_alarm_bit(RC_PRCn_ECC_SG_ERR |
4592 RC_RDA_FAIL_WR_Rn, &bar0->rc_err_reg,
4593 &sw_stat->rc_err_cnt);
4594 if (do_s2io_chk_alarm_bit(PRC_PCI_AB_RD_Rn |
4597 &bar0->prc_pcix_err_reg,
4598 &sw_stat->prc_pcix_err_cnt))
4600 do_s2io_chk_alarm_bit(PRC_PCI_DP_RD_Rn |
4603 &bar0->prc_pcix_err_reg,
4604 &sw_stat->prc_pcix_err_cnt);
4607 if (val64 & RXDMA_INT_RPA_INT_M) {
4608 if (do_s2io_chk_alarm_bit(RPA_SM_ERR_ALARM | RPA_CREDIT_ERR,
4610 &sw_stat->rpa_err_cnt))
4612 do_s2io_chk_alarm_bit(RPA_ECC_SG_ERR | RPA_ECC_DB_ERR,
4614 &sw_stat->rpa_err_cnt);
4617 if (val64 & RXDMA_INT_RDA_INT_M) {
4618 if (do_s2io_chk_alarm_bit(RDA_RXDn_ECC_DB_ERR |
4619 RDA_FRM_ECC_DB_N_AERR |
4622 RDA_RXD_ECC_DB_SERR,
4624 &sw_stat->rda_err_cnt))
4626 do_s2io_chk_alarm_bit(RDA_RXDn_ECC_SG_ERR |
4627 RDA_FRM_ECC_SG_ERR |
4631 &sw_stat->rda_err_cnt);
4634 if (val64 & RXDMA_INT_RTI_INT_M) {
4635 if (do_s2io_chk_alarm_bit(RTI_SM_ERR_ALARM,
4637 &sw_stat->rti_err_cnt))
4639 do_s2io_chk_alarm_bit(RTI_ECC_SG_ERR | RTI_ECC_DB_ERR,
4641 &sw_stat->rti_err_cnt);
4644 val64 = readq(&bar0->mac_int_status);
4645 if (val64 & MAC_INT_STATUS_RMAC_INT) {
4646 if (do_s2io_chk_alarm_bit(RMAC_RX_BUFF_OVRN | RMAC_RX_SM_ERR,
4647 &bar0->mac_rmac_err_reg,
4648 &sw_stat->mac_rmac_err_cnt))
4650 do_s2io_chk_alarm_bit(RMAC_UNUSED_INT |
4651 RMAC_SINGLE_ECC_ERR |
4652 RMAC_DOUBLE_ECC_ERR,
4653 &bar0->mac_rmac_err_reg,
4654 &sw_stat->mac_rmac_err_cnt);
4657 val64 = readq(&bar0->xgxs_int_status);
4658 if (val64 & XGXS_INT_STATUS_RXGXS) {
4659 if (do_s2io_chk_alarm_bit(RXGXS_ESTORE_OFLOW | RXGXS_RX_SM_ERR,
4660 &bar0->xgxs_rxgxs_err_reg,
4661 &sw_stat->xgxs_rxgxs_err_cnt))
4665 val64 = readq(&bar0->mc_int_status);
4666 if (val64 & MC_INT_STATUS_MC_INT) {
4667 if (do_s2io_chk_alarm_bit(MC_ERR_REG_SM_ERR,
4669 &sw_stat->mc_err_cnt))
4672 /* Handling Ecc errors */
4673 if (val64 & (MC_ERR_REG_ECC_ALL_SNG | MC_ERR_REG_ECC_ALL_DBL)) {
4674 writeq(val64, &bar0->mc_err_reg);
4675 if (val64 & MC_ERR_REG_ECC_ALL_DBL) {
4676 sw_stat->double_ecc_errs++;
4677 if (sp->device_type != XFRAME_II_DEVICE) {
4679 * Reset XframeI only if critical error
4682 (MC_ERR_REG_MIRI_ECC_DB_ERR_0 |
4683 MC_ERR_REG_MIRI_ECC_DB_ERR_1))
4687 sw_stat->single_ecc_errs++;
4693 s2io_stop_all_tx_queue(sp);
4694 schedule_work(&sp->rst_timer_task);
4695 sw_stat->soft_reset_cnt++;
4699 * s2io_isr - ISR handler of the device .
4700 * @irq: the irq of the device.
4701 * @dev_id: a void pointer to the dev structure of the NIC.
4702 * Description: This function is the ISR handler of the device. It
4703 * identifies the reason for the interrupt and calls the relevant
4704 * service routines. As a contongency measure, this ISR allocates the
4705 * recv buffers, if their numbers are below the panic value which is
4706 * presently set to 25% of the original number of rcv buffers allocated.
4708 * IRQ_HANDLED: will be returned if IRQ was handled by this routine
4709 * IRQ_NONE: will be returned if interrupt is not from our device
4711 static irqreturn_t s2io_isr(int irq, void *dev_id)
4713 struct net_device *dev = (struct net_device *)dev_id;
4714 struct s2io_nic *sp = netdev_priv(dev);
4715 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4718 struct mac_info *mac_control;
4719 struct config_param *config;
4721 /* Pretend we handled any irq's from a disconnected card */
4722 if (pci_channel_offline(sp->pdev))
4725 if (!is_s2io_card_up(sp))
4728 config = &sp->config;
4729 mac_control = &sp->mac_control;
4732 * Identify the cause for interrupt and call the appropriate
4733 * interrupt handler. Causes for the interrupt could be;
4738 reason = readq(&bar0->general_int_status);
4740 if (unlikely(reason == S2IO_MINUS_ONE))
4741 return IRQ_HANDLED; /* Nothing much can be done. Get out */
4744 (GEN_INTR_RXTRAFFIC | GEN_INTR_TXTRAFFIC | GEN_INTR_TXPIC)) {
4745 writeq(S2IO_MINUS_ONE, &bar0->general_int_mask);
4748 if (reason & GEN_INTR_RXTRAFFIC) {
4749 napi_schedule(&sp->napi);
4750 writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_mask);
4751 writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
4752 readl(&bar0->rx_traffic_int);
4756 * rx_traffic_int reg is an R1 register, writing all 1's
4757 * will ensure that the actual interrupt causing bit
4758 * get's cleared and hence a read can be avoided.
4760 if (reason & GEN_INTR_RXTRAFFIC)
4761 writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
4763 for (i = 0; i < config->rx_ring_num; i++) {
4764 struct ring_info *ring = &mac_control->rings[i];
4766 rx_intr_handler(ring, 0);
4771 * tx_traffic_int reg is an R1 register, writing all 1's
4772 * will ensure that the actual interrupt causing bit get's
4773 * cleared and hence a read can be avoided.
4775 if (reason & GEN_INTR_TXTRAFFIC)
4776 writeq(S2IO_MINUS_ONE, &bar0->tx_traffic_int);
4778 for (i = 0; i < config->tx_fifo_num; i++)
4779 tx_intr_handler(&mac_control->fifos[i]);
4781 if (reason & GEN_INTR_TXPIC)
4782 s2io_txpic_intr_handle(sp);
4785 * Reallocate the buffers from the interrupt handler itself.
4787 if (!config->napi) {
4788 for (i = 0; i < config->rx_ring_num; i++) {
4789 struct ring_info *ring = &mac_control->rings[i];
4791 s2io_chk_rx_buffers(sp, ring);
4794 writeq(sp->general_int_mask, &bar0->general_int_mask);
4795 readl(&bar0->general_int_status);
4799 } else if (!reason) {
4800 /* The interrupt was not raised by us */
4810 static void s2io_updt_stats(struct s2io_nic *sp)
4812 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4816 if (is_s2io_card_up(sp)) {
4817 /* Apprx 30us on a 133 MHz bus */
4818 val64 = SET_UPDT_CLICKS(10) |
4819 STAT_CFG_ONE_SHOT_EN | STAT_CFG_STAT_EN;
4820 writeq(val64, &bar0->stat_cfg);
4823 val64 = readq(&bar0->stat_cfg);
4824 if (!(val64 & s2BIT(0)))
4828 break; /* Updt failed */
4834 * s2io_get_stats - Updates the device statistics structure.
4835 * @dev : pointer to the device structure.
4837 * This function updates the device statistics structure in the s2io_nic
4838 * structure and returns a pointer to the same.
4840 * pointer to the updated net_device_stats structure.
4842 static struct net_device_stats *s2io_get_stats(struct net_device *dev)
4844 struct s2io_nic *sp = netdev_priv(dev);
4845 struct mac_info *mac_control = &sp->mac_control;
4846 struct stat_block *stats = mac_control->stats_info;
4849 /* Configure Stats for immediate updt */
4850 s2io_updt_stats(sp);
4852 /* A device reset will cause the on-adapter statistics to be zero'ed.
4853 * This can be done while running by changing the MTU. To prevent the
4854 * system from having the stats zero'ed, the driver keeps a copy of the
4855 * last update to the system (which is also zero'ed on reset). This
4856 * enables the driver to accurately know the delta between the last
4857 * update and the current update.
4859 delta = ((u64) le32_to_cpu(stats->rmac_vld_frms_oflow) << 32 |
4860 le32_to_cpu(stats->rmac_vld_frms)) - sp->stats.rx_packets;
4861 sp->stats.rx_packets += delta;
4862 dev->stats.rx_packets += delta;
4864 delta = ((u64) le32_to_cpu(stats->tmac_frms_oflow) << 32 |
4865 le32_to_cpu(stats->tmac_frms)) - sp->stats.tx_packets;
4866 sp->stats.tx_packets += delta;
4867 dev->stats.tx_packets += delta;
4869 delta = ((u64) le32_to_cpu(stats->rmac_data_octets_oflow) << 32 |
4870 le32_to_cpu(stats->rmac_data_octets)) - sp->stats.rx_bytes;
4871 sp->stats.rx_bytes += delta;
4872 dev->stats.rx_bytes += delta;
4874 delta = ((u64) le32_to_cpu(stats->tmac_data_octets_oflow) << 32 |
4875 le32_to_cpu(stats->tmac_data_octets)) - sp->stats.tx_bytes;
4876 sp->stats.tx_bytes += delta;
4877 dev->stats.tx_bytes += delta;
4879 delta = le64_to_cpu(stats->rmac_drop_frms) - sp->stats.rx_errors;
4880 sp->stats.rx_errors += delta;
4881 dev->stats.rx_errors += delta;
4883 delta = ((u64) le32_to_cpu(stats->tmac_any_err_frms_oflow) << 32 |
4884 le32_to_cpu(stats->tmac_any_err_frms)) - sp->stats.tx_errors;
4885 sp->stats.tx_errors += delta;
4886 dev->stats.tx_errors += delta;
4888 delta = le64_to_cpu(stats->rmac_drop_frms) - sp->stats.rx_dropped;
4889 sp->stats.rx_dropped += delta;
4890 dev->stats.rx_dropped += delta;
4892 delta = le64_to_cpu(stats->tmac_drop_frms) - sp->stats.tx_dropped;
4893 sp->stats.tx_dropped += delta;
4894 dev->stats.tx_dropped += delta;
4896 /* The adapter MAC interprets pause frames as multicast packets, but
4897 * does not pass them up. This erroneously increases the multicast
4898 * packet count and needs to be deducted when the multicast frame count
4901 delta = (u64) le32_to_cpu(stats->rmac_vld_mcst_frms_oflow) << 32 |
4902 le32_to_cpu(stats->rmac_vld_mcst_frms);
4903 delta -= le64_to_cpu(stats->rmac_pause_ctrl_frms);
4904 delta -= sp->stats.multicast;
4905 sp->stats.multicast += delta;
4906 dev->stats.multicast += delta;
4908 delta = ((u64) le32_to_cpu(stats->rmac_usized_frms_oflow) << 32 |
4909 le32_to_cpu(stats->rmac_usized_frms)) +
4910 le64_to_cpu(stats->rmac_long_frms) - sp->stats.rx_length_errors;
4911 sp->stats.rx_length_errors += delta;
4912 dev->stats.rx_length_errors += delta;
4914 delta = le64_to_cpu(stats->rmac_fcs_err_frms) - sp->stats.rx_crc_errors;
4915 sp->stats.rx_crc_errors += delta;
4916 dev->stats.rx_crc_errors += delta;
4922 * s2io_set_multicast - entry point for multicast address enable/disable.
4923 * @dev : pointer to the device structure
4925 * This function is a driver entry point which gets called by the kernel
4926 * whenever multicast addresses must be enabled/disabled. This also gets
4927 * called to set/reset promiscuous mode. Depending on the deivce flag, we
4928 * determine, if multicast address must be enabled or if promiscuous mode
4929 * is to be disabled etc.
4934 static void s2io_set_multicast(struct net_device *dev)
4937 struct netdev_hw_addr *ha;
4938 struct s2io_nic *sp = netdev_priv(dev);
4939 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4940 u64 val64 = 0, multi_mac = 0x010203040506ULL, mask =
4942 u64 dis_addr = S2IO_DISABLE_MAC_ENTRY, mac_addr = 0;
4944 struct config_param *config = &sp->config;
4946 if ((dev->flags & IFF_ALLMULTI) && (!sp->m_cast_flg)) {
4947 /* Enable all Multicast addresses */
4948 writeq(RMAC_ADDR_DATA0_MEM_ADDR(multi_mac),
4949 &bar0->rmac_addr_data0_mem);
4950 writeq(RMAC_ADDR_DATA1_MEM_MASK(mask),
4951 &bar0->rmac_addr_data1_mem);
4952 val64 = RMAC_ADDR_CMD_MEM_WE |
4953 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4954 RMAC_ADDR_CMD_MEM_OFFSET(config->max_mc_addr - 1);
4955 writeq(val64, &bar0->rmac_addr_cmd_mem);
4956 /* Wait till command completes */
4957 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4958 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
4962 sp->all_multi_pos = config->max_mc_addr - 1;
4963 } else if ((dev->flags & IFF_ALLMULTI) && (sp->m_cast_flg)) {
4964 /* Disable all Multicast addresses */
4965 writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr),
4966 &bar0->rmac_addr_data0_mem);
4967 writeq(RMAC_ADDR_DATA1_MEM_MASK(0x0),
4968 &bar0->rmac_addr_data1_mem);
4969 val64 = RMAC_ADDR_CMD_MEM_WE |
4970 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4971 RMAC_ADDR_CMD_MEM_OFFSET(sp->all_multi_pos);
4972 writeq(val64, &bar0->rmac_addr_cmd_mem);
4973 /* Wait till command completes */
4974 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4975 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
4979 sp->all_multi_pos = 0;
4982 if ((dev->flags & IFF_PROMISC) && (!sp->promisc_flg)) {
4983 /* Put the NIC into promiscuous mode */
4984 add = &bar0->mac_cfg;
4985 val64 = readq(&bar0->mac_cfg);
4986 val64 |= MAC_CFG_RMAC_PROM_ENABLE;
4988 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
4989 writel((u32)val64, add);
4990 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
4991 writel((u32) (val64 >> 32), (add + 4));
4993 if (vlan_tag_strip != 1) {
4994 val64 = readq(&bar0->rx_pa_cfg);
4995 val64 &= ~RX_PA_CFG_STRIP_VLAN_TAG;
4996 writeq(val64, &bar0->rx_pa_cfg);
4997 sp->vlan_strip_flag = 0;
5000 val64 = readq(&bar0->mac_cfg);
5001 sp->promisc_flg = 1;
5002 DBG_PRINT(INFO_DBG, "%s: entered promiscuous mode\n",
5004 } else if (!(dev->flags & IFF_PROMISC) && (sp->promisc_flg)) {
5005 /* Remove the NIC from promiscuous mode */
5006 add = &bar0->mac_cfg;
5007 val64 = readq(&bar0->mac_cfg);
5008 val64 &= ~MAC_CFG_RMAC_PROM_ENABLE;
5010 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
5011 writel((u32)val64, add);
5012 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
5013 writel((u32) (val64 >> 32), (add + 4));
5015 if (vlan_tag_strip != 0) {
5016 val64 = readq(&bar0->rx_pa_cfg);
5017 val64 |= RX_PA_CFG_STRIP_VLAN_TAG;
5018 writeq(val64, &bar0->rx_pa_cfg);
5019 sp->vlan_strip_flag = 1;
5022 val64 = readq(&bar0->mac_cfg);
5023 sp->promisc_flg = 0;
5024 DBG_PRINT(INFO_DBG, "%s: left promiscuous mode\n", dev->name);
5027 /* Update individual M_CAST address list */
5028 if ((!sp->m_cast_flg) && netdev_mc_count(dev)) {
5029 if (netdev_mc_count(dev) >
5030 (config->max_mc_addr - config->max_mac_addr)) {
5032 "%s: No more Rx filters can be added - "
5033 "please enable ALL_MULTI instead\n",
5038 prev_cnt = sp->mc_addr_count;
5039 sp->mc_addr_count = netdev_mc_count(dev);
5041 /* Clear out the previous list of Mc in the H/W. */
5042 for (i = 0; i < prev_cnt; i++) {
5043 writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr),
5044 &bar0->rmac_addr_data0_mem);
5045 writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL),
5046 &bar0->rmac_addr_data1_mem);
5047 val64 = RMAC_ADDR_CMD_MEM_WE |
5048 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5049 RMAC_ADDR_CMD_MEM_OFFSET
5050 (config->mc_start_offset + i);
5051 writeq(val64, &bar0->rmac_addr_cmd_mem);
5053 /* Wait for command completes */
5054 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5055 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5058 "%s: Adding Multicasts failed\n",
5064 /* Create the new Rx filter list and update the same in H/W. */
5066 netdev_for_each_mc_addr(ha, dev) {
5068 for (j = 0; j < ETH_ALEN; j++) {
5069 mac_addr |= ha->addr[j];
5073 writeq(RMAC_ADDR_DATA0_MEM_ADDR(mac_addr),
5074 &bar0->rmac_addr_data0_mem);
5075 writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL),
5076 &bar0->rmac_addr_data1_mem);
5077 val64 = RMAC_ADDR_CMD_MEM_WE |
5078 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5079 RMAC_ADDR_CMD_MEM_OFFSET
5080 (i + config->mc_start_offset);
5081 writeq(val64, &bar0->rmac_addr_cmd_mem);
5083 /* Wait for command completes */
5084 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5085 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5088 "%s: Adding Multicasts failed\n",
5097 /* read from CAM unicast & multicast addresses and store it in
5098 * def_mac_addr structure
5100 static void do_s2io_store_unicast_mc(struct s2io_nic *sp)
5104 struct config_param *config = &sp->config;
5106 /* store unicast & multicast mac addresses */
5107 for (offset = 0; offset < config->max_mc_addr; offset++) {
5108 mac_addr = do_s2io_read_unicast_mc(sp, offset);
5109 /* if read fails disable the entry */
5110 if (mac_addr == FAILURE)
5111 mac_addr = S2IO_DISABLE_MAC_ENTRY;
5112 do_s2io_copy_mac_addr(sp, offset, mac_addr);
5116 /* restore unicast & multicast MAC to CAM from def_mac_addr structure */
5117 static void do_s2io_restore_unicast_mc(struct s2io_nic *sp)
5120 struct config_param *config = &sp->config;
5121 /* restore unicast mac address */
5122 for (offset = 0; offset < config->max_mac_addr; offset++)
5123 do_s2io_prog_unicast(sp->dev,
5124 sp->def_mac_addr[offset].mac_addr);
5126 /* restore multicast mac address */
5127 for (offset = config->mc_start_offset;
5128 offset < config->max_mc_addr; offset++)
5129 do_s2io_add_mc(sp, sp->def_mac_addr[offset].mac_addr);
5132 /* add a multicast MAC address to CAM */
5133 static int do_s2io_add_mc(struct s2io_nic *sp, u8 *addr)
5137 struct config_param *config = &sp->config;
5139 for (i = 0; i < ETH_ALEN; i++) {
5141 mac_addr |= addr[i];
5143 if ((0ULL == mac_addr) || (mac_addr == S2IO_DISABLE_MAC_ENTRY))
5146 /* check if the multicast mac already preset in CAM */
5147 for (i = config->mc_start_offset; i < config->max_mc_addr; i++) {
5149 tmp64 = do_s2io_read_unicast_mc(sp, i);
5150 if (tmp64 == S2IO_DISABLE_MAC_ENTRY) /* CAM entry is empty */
5153 if (tmp64 == mac_addr)
5156 if (i == config->max_mc_addr) {
5158 "CAM full no space left for multicast MAC\n");
5161 /* Update the internal structure with this new mac address */
5162 do_s2io_copy_mac_addr(sp, i, mac_addr);
5164 return do_s2io_add_mac(sp, mac_addr, i);
5167 /* add MAC address to CAM */
5168 static int do_s2io_add_mac(struct s2io_nic *sp, u64 addr, int off)
5171 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5173 writeq(RMAC_ADDR_DATA0_MEM_ADDR(addr),
5174 &bar0->rmac_addr_data0_mem);
5176 val64 = RMAC_ADDR_CMD_MEM_WE | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5177 RMAC_ADDR_CMD_MEM_OFFSET(off);
5178 writeq(val64, &bar0->rmac_addr_cmd_mem);
5180 /* Wait till command completes */
5181 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5182 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5184 DBG_PRINT(INFO_DBG, "do_s2io_add_mac failed\n");
5189 /* deletes a specified unicast/multicast mac entry from CAM */
5190 static int do_s2io_delete_unicast_mc(struct s2io_nic *sp, u64 addr)
5193 u64 dis_addr = S2IO_DISABLE_MAC_ENTRY, tmp64;
5194 struct config_param *config = &sp->config;
5197 offset < config->max_mc_addr; offset++) {
5198 tmp64 = do_s2io_read_unicast_mc(sp, offset);
5199 if (tmp64 == addr) {
5200 /* disable the entry by writing 0xffffffffffffULL */
5201 if (do_s2io_add_mac(sp, dis_addr, offset) == FAILURE)
5203 /* store the new mac list from CAM */
5204 do_s2io_store_unicast_mc(sp);
5208 DBG_PRINT(ERR_DBG, "MAC address 0x%llx not found in CAM\n",
5209 (unsigned long long)addr);
5213 /* read mac entries from CAM */
5214 static u64 do_s2io_read_unicast_mc(struct s2io_nic *sp, int offset)
5216 u64 tmp64 = 0xffffffffffff0000ULL, val64;
5217 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5220 val64 = RMAC_ADDR_CMD_MEM_RD | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
5221 RMAC_ADDR_CMD_MEM_OFFSET(offset);
5222 writeq(val64, &bar0->rmac_addr_cmd_mem);
5224 /* Wait till command completes */
5225 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
5226 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
5228 DBG_PRINT(INFO_DBG, "do_s2io_read_unicast_mc failed\n");
5231 tmp64 = readq(&bar0->rmac_addr_data0_mem);
5237 * s2io_set_mac_addr - driver entry point
5240 static int s2io_set_mac_addr(struct net_device *dev, void *p)
5242 struct sockaddr *addr = p;
5244 if (!is_valid_ether_addr(addr->sa_data))
5245 return -EADDRNOTAVAIL;
5247 memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
5249 /* store the MAC address in CAM */
5250 return do_s2io_prog_unicast(dev, dev->dev_addr);
5253 * do_s2io_prog_unicast - Programs the Xframe mac address
5254 * @dev : pointer to the device structure.
5255 * @addr: a uchar pointer to the new mac address which is to be set.
5256 * Description : This procedure will program the Xframe to receive
5257 * frames with new Mac Address
5258 * Return value: SUCCESS on success and an appropriate (-)ve integer
5259 * as defined in errno.h file on failure.
5262 static int do_s2io_prog_unicast(struct net_device *dev, u8 *addr)
5264 struct s2io_nic *sp = netdev_priv(dev);
5265 register u64 mac_addr = 0, perm_addr = 0;
5268 struct config_param *config = &sp->config;
5271 * Set the new MAC address as the new unicast filter and reflect this
5272 * change on the device address registered with the OS. It will be
5275 for (i = 0; i < ETH_ALEN; i++) {
5277 mac_addr |= addr[i];
5279 perm_addr |= sp->def_mac_addr[0].mac_addr[i];
5282 /* check if the dev_addr is different than perm_addr */
5283 if (mac_addr == perm_addr)
5286 /* check if the mac already preset in CAM */
5287 for (i = 1; i < config->max_mac_addr; i++) {
5288 tmp64 = do_s2io_read_unicast_mc(sp, i);
5289 if (tmp64 == S2IO_DISABLE_MAC_ENTRY) /* CAM entry is empty */
5292 if (tmp64 == mac_addr) {
5294 "MAC addr:0x%llx already present in CAM\n",
5295 (unsigned long long)mac_addr);
5299 if (i == config->max_mac_addr) {
5300 DBG_PRINT(ERR_DBG, "CAM full no space left for Unicast MAC\n");
5303 /* Update the internal structure with this new mac address */
5304 do_s2io_copy_mac_addr(sp, i, mac_addr);
5306 return do_s2io_add_mac(sp, mac_addr, i);
5310 * s2io_ethtool_sset - Sets different link parameters.
5311 * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
5312 * @info: pointer to the structure with parameters given by ethtool to set
5315 * The function sets different link parameters provided by the user onto
5321 static int s2io_ethtool_sset(struct net_device *dev,
5322 struct ethtool_cmd *info)
5324 struct s2io_nic *sp = netdev_priv(dev);
5325 if ((info->autoneg == AUTONEG_ENABLE) ||
5326 (ethtool_cmd_speed(info) != SPEED_10000) ||
5327 (info->duplex != DUPLEX_FULL))
5330 s2io_close(sp->dev);
5338 * s2io_ethtol_gset - Return link specific information.
5339 * @sp : private member of the device structure, pointer to the
5340 * s2io_nic structure.
5341 * @info : pointer to the structure with parameters given by ethtool
5342 * to return link information.
5344 * Returns link specific information like speed, duplex etc.. to ethtool.
5346 * return 0 on success.
5349 static int s2io_ethtool_gset(struct net_device *dev, struct ethtool_cmd *info)
5351 struct s2io_nic *sp = netdev_priv(dev);
5352 info->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
5353 info->advertising = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
5354 info->port = PORT_FIBRE;
5356 /* info->transceiver */
5357 info->transceiver = XCVR_EXTERNAL;
5359 if (netif_carrier_ok(sp->dev)) {
5360 ethtool_cmd_speed_set(info, SPEED_10000);
5361 info->duplex = DUPLEX_FULL;
5363 ethtool_cmd_speed_set(info, SPEED_UNKNOWN);
5364 info->duplex = DUPLEX_UNKNOWN;
5367 info->autoneg = AUTONEG_DISABLE;
5372 * s2io_ethtool_gdrvinfo - Returns driver specific information.
5373 * @sp : private member of the device structure, which is a pointer to the
5374 * s2io_nic structure.
5375 * @info : pointer to the structure with parameters given by ethtool to
5376 * return driver information.
5378 * Returns driver specefic information like name, version etc.. to ethtool.
5383 static void s2io_ethtool_gdrvinfo(struct net_device *dev,
5384 struct ethtool_drvinfo *info)
5386 struct s2io_nic *sp = netdev_priv(dev);
5388 strlcpy(info->driver, s2io_driver_name, sizeof(info->driver));
5389 strlcpy(info->version, s2io_driver_version, sizeof(info->version));
5390 strlcpy(info->bus_info, pci_name(sp->pdev), sizeof(info->bus_info));
5391 info->regdump_len = XENA_REG_SPACE;
5392 info->eedump_len = XENA_EEPROM_SPACE;
5396 * s2io_ethtool_gregs - dumps the entire space of Xfame into the buffer.
5397 * @sp: private member of the device structure, which is a pointer to the
5398 * s2io_nic structure.
5399 * @regs : pointer to the structure with parameters given by ethtool for
5400 * dumping the registers.
5401 * @reg_space: The input argumnet into which all the registers are dumped.
5403 * Dumps the entire register space of xFrame NIC into the user given
5409 static void s2io_ethtool_gregs(struct net_device *dev,
5410 struct ethtool_regs *regs, void *space)
5414 u8 *reg_space = (u8 *)space;
5415 struct s2io_nic *sp = netdev_priv(dev);
5417 regs->len = XENA_REG_SPACE;
5418 regs->version = sp->pdev->subsystem_device;
5420 for (i = 0; i < regs->len; i += 8) {
5421 reg = readq(sp->bar0 + i);
5422 memcpy((reg_space + i), ®, 8);
5427 * s2io_set_led - control NIC led
5429 static void s2io_set_led(struct s2io_nic *sp, bool on)
5431 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5432 u16 subid = sp->pdev->subsystem_device;
5435 if ((sp->device_type == XFRAME_II_DEVICE) ||
5436 ((subid & 0xFF) >= 0x07)) {
5437 val64 = readq(&bar0->gpio_control);
5439 val64 |= GPIO_CTRL_GPIO_0;
5441 val64 &= ~GPIO_CTRL_GPIO_0;
5443 writeq(val64, &bar0->gpio_control);
5445 val64 = readq(&bar0->adapter_control);
5447 val64 |= ADAPTER_LED_ON;
5449 val64 &= ~ADAPTER_LED_ON;
5451 writeq(val64, &bar0->adapter_control);
5457 * s2io_ethtool_set_led - To physically identify the nic on the system.
5458 * @dev : network device
5459 * @state: led setting
5461 * Description: Used to physically identify the NIC on the system.
5462 * The Link LED will blink for a time specified by the user for
5464 * NOTE: The Link has to be Up to be able to blink the LED. Hence
5465 * identification is possible only if it's link is up.
5468 static int s2io_ethtool_set_led(struct net_device *dev,
5469 enum ethtool_phys_id_state state)
5471 struct s2io_nic *sp = netdev_priv(dev);
5472 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5473 u16 subid = sp->pdev->subsystem_device;
5475 if ((sp->device_type == XFRAME_I_DEVICE) && ((subid & 0xFF) < 0x07)) {
5476 u64 val64 = readq(&bar0->adapter_control);
5477 if (!(val64 & ADAPTER_CNTL_EN)) {
5478 pr_err("Adapter Link down, cannot blink LED\n");
5484 case ETHTOOL_ID_ACTIVE:
5485 sp->adapt_ctrl_org = readq(&bar0->gpio_control);
5486 return 1; /* cycle on/off once per second */
5489 s2io_set_led(sp, true);
5492 case ETHTOOL_ID_OFF:
5493 s2io_set_led(sp, false);
5496 case ETHTOOL_ID_INACTIVE:
5497 if (CARDS_WITH_FAULTY_LINK_INDICATORS(sp->device_type, subid))
5498 writeq(sp->adapt_ctrl_org, &bar0->gpio_control);
5504 static void s2io_ethtool_gringparam(struct net_device *dev,
5505 struct ethtool_ringparam *ering)
5507 struct s2io_nic *sp = netdev_priv(dev);
5508 int i, tx_desc_count = 0, rx_desc_count = 0;
5510 if (sp->rxd_mode == RXD_MODE_1) {
5511 ering->rx_max_pending = MAX_RX_DESC_1;
5512 ering->rx_jumbo_max_pending = MAX_RX_DESC_1;
5514 ering->rx_max_pending = MAX_RX_DESC_2;
5515 ering->rx_jumbo_max_pending = MAX_RX_DESC_2;
5518 ering->tx_max_pending = MAX_TX_DESC;
5520 for (i = 0; i < sp->config.rx_ring_num; i++)
5521 rx_desc_count += sp->config.rx_cfg[i].num_rxd;
5522 ering->rx_pending = rx_desc_count;
5523 ering->rx_jumbo_pending = rx_desc_count;
5525 for (i = 0; i < sp->config.tx_fifo_num; i++)
5526 tx_desc_count += sp->config.tx_cfg[i].fifo_len;
5527 ering->tx_pending = tx_desc_count;
5528 DBG_PRINT(INFO_DBG, "max txds: %d\n", sp->config.max_txds);
5532 * s2io_ethtool_getpause_data -Pause frame frame generation and reception.
5533 * @sp : private member of the device structure, which is a pointer to the
5534 * s2io_nic structure.
5535 * @ep : pointer to the structure with pause parameters given by ethtool.
5537 * Returns the Pause frame generation and reception capability of the NIC.
5541 static void s2io_ethtool_getpause_data(struct net_device *dev,
5542 struct ethtool_pauseparam *ep)
5545 struct s2io_nic *sp = netdev_priv(dev);
5546 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5548 val64 = readq(&bar0->rmac_pause_cfg);
5549 if (val64 & RMAC_PAUSE_GEN_ENABLE)
5550 ep->tx_pause = true;
5551 if (val64 & RMAC_PAUSE_RX_ENABLE)
5552 ep->rx_pause = true;
5553 ep->autoneg = false;
5557 * s2io_ethtool_setpause_data - set/reset pause frame generation.
5558 * @sp : private member of the device structure, which is a pointer to the
5559 * s2io_nic structure.
5560 * @ep : pointer to the structure with pause parameters given by ethtool.
5562 * It can be used to set or reset Pause frame generation or reception
5563 * support of the NIC.
5565 * int, returns 0 on Success
5568 static int s2io_ethtool_setpause_data(struct net_device *dev,
5569 struct ethtool_pauseparam *ep)
5572 struct s2io_nic *sp = netdev_priv(dev);
5573 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5575 val64 = readq(&bar0->rmac_pause_cfg);
5577 val64 |= RMAC_PAUSE_GEN_ENABLE;
5579 val64 &= ~RMAC_PAUSE_GEN_ENABLE;
5581 val64 |= RMAC_PAUSE_RX_ENABLE;
5583 val64 &= ~RMAC_PAUSE_RX_ENABLE;
5584 writeq(val64, &bar0->rmac_pause_cfg);
5589 * read_eeprom - reads 4 bytes of data from user given offset.
5590 * @sp : private member of the device structure, which is a pointer to the
5591 * s2io_nic structure.
5592 * @off : offset at which the data must be written
5593 * @data : Its an output parameter where the data read at the given
5596 * Will read 4 bytes of data from the user given offset and return the
5598 * NOTE: Will allow to read only part of the EEPROM visible through the
5601 * -1 on failure and 0 on success.
5604 #define S2IO_DEV_ID 5
5605 static int read_eeprom(struct s2io_nic *sp, int off, u64 *data)
5610 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5612 if (sp->device_type == XFRAME_I_DEVICE) {
5613 val64 = I2C_CONTROL_DEV_ID(S2IO_DEV_ID) |
5614 I2C_CONTROL_ADDR(off) |
5615 I2C_CONTROL_BYTE_CNT(0x3) |
5617 I2C_CONTROL_CNTL_START;
5618 SPECIAL_REG_WRITE(val64, &bar0->i2c_control, LF);
5620 while (exit_cnt < 5) {
5621 val64 = readq(&bar0->i2c_control);
5622 if (I2C_CONTROL_CNTL_END(val64)) {
5623 *data = I2C_CONTROL_GET_DATA(val64);
5632 if (sp->device_type == XFRAME_II_DEVICE) {
5633 val64 = SPI_CONTROL_KEY(0x9) | SPI_CONTROL_SEL1 |
5634 SPI_CONTROL_BYTECNT(0x3) |
5635 SPI_CONTROL_CMD(0x3) | SPI_CONTROL_ADDR(off);
5636 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5637 val64 |= SPI_CONTROL_REQ;
5638 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5639 while (exit_cnt < 5) {
5640 val64 = readq(&bar0->spi_control);
5641 if (val64 & SPI_CONTROL_NACK) {
5644 } else if (val64 & SPI_CONTROL_DONE) {
5645 *data = readq(&bar0->spi_data);
5658 * write_eeprom - actually writes the relevant part of the data value.
5659 * @sp : private member of the device structure, which is a pointer to the
5660 * s2io_nic structure.
5661 * @off : offset at which the data must be written
5662 * @data : The data that is to be written
5663 * @cnt : Number of bytes of the data that are actually to be written into
5664 * the Eeprom. (max of 3)
5666 * Actually writes the relevant part of the data value into the Eeprom
5667 * through the I2C bus.
5669 * 0 on success, -1 on failure.
5672 static int write_eeprom(struct s2io_nic *sp, int off, u64 data, int cnt)
5674 int exit_cnt = 0, ret = -1;
5676 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5678 if (sp->device_type == XFRAME_I_DEVICE) {
5679 val64 = I2C_CONTROL_DEV_ID(S2IO_DEV_ID) |
5680 I2C_CONTROL_ADDR(off) |
5681 I2C_CONTROL_BYTE_CNT(cnt) |
5682 I2C_CONTROL_SET_DATA((u32)data) |
5683 I2C_CONTROL_CNTL_START;
5684 SPECIAL_REG_WRITE(val64, &bar0->i2c_control, LF);
5686 while (exit_cnt < 5) {
5687 val64 = readq(&bar0->i2c_control);
5688 if (I2C_CONTROL_CNTL_END(val64)) {
5689 if (!(val64 & I2C_CONTROL_NACK))
5698 if (sp->device_type == XFRAME_II_DEVICE) {
5699 int write_cnt = (cnt == 8) ? 0 : cnt;
5700 writeq(SPI_DATA_WRITE(data, (cnt << 3)), &bar0->spi_data);
5702 val64 = SPI_CONTROL_KEY(0x9) | SPI_CONTROL_SEL1 |
5703 SPI_CONTROL_BYTECNT(write_cnt) |
5704 SPI_CONTROL_CMD(0x2) | SPI_CONTROL_ADDR(off);
5705 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5706 val64 |= SPI_CONTROL_REQ;
5707 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5708 while (exit_cnt < 5) {
5709 val64 = readq(&bar0->spi_control);
5710 if (val64 & SPI_CONTROL_NACK) {
5713 } else if (val64 & SPI_CONTROL_DONE) {
5723 static void s2io_vpd_read(struct s2io_nic *nic)
5727 int i = 0, cnt, len, fail = 0;
5728 int vpd_addr = 0x80;
5729 struct swStat *swstats = &nic->mac_control.stats_info->sw_stat;
5731 if (nic->device_type == XFRAME_II_DEVICE) {
5732 strcpy(nic->product_name, "Xframe II 10GbE network adapter");
5735 strcpy(nic->product_name, "Xframe I 10GbE network adapter");
5738 strcpy(nic->serial_num, "NOT AVAILABLE");
5740 vpd_data = kmalloc(256, GFP_KERNEL);
5742 swstats->mem_alloc_fail_cnt++;
5745 swstats->mem_allocated += 256;
5747 for (i = 0; i < 256; i += 4) {
5748 pci_write_config_byte(nic->pdev, (vpd_addr + 2), i);
5749 pci_read_config_byte(nic->pdev, (vpd_addr + 2), &data);
5750 pci_write_config_byte(nic->pdev, (vpd_addr + 3), 0);
5751 for (cnt = 0; cnt < 5; cnt++) {
5753 pci_read_config_byte(nic->pdev, (vpd_addr + 3), &data);
5758 DBG_PRINT(ERR_DBG, "Read of VPD data failed\n");
5762 pci_read_config_dword(nic->pdev, (vpd_addr + 4),
5763 (u32 *)&vpd_data[i]);
5767 /* read serial number of adapter */
5768 for (cnt = 0; cnt < 252; cnt++) {
5769 if ((vpd_data[cnt] == 'S') &&
5770 (vpd_data[cnt+1] == 'N')) {
5771 len = vpd_data[cnt+2];
5772 if (len < min(VPD_STRING_LEN, 256-cnt-2)) {
5773 memcpy(nic->serial_num,
5776 memset(nic->serial_num+len,
5778 VPD_STRING_LEN-len);
5785 if ((!fail) && (vpd_data[1] < VPD_STRING_LEN)) {
5787 memcpy(nic->product_name, &vpd_data[3], len);
5788 nic->product_name[len] = 0;
5791 swstats->mem_freed += 256;
5795 * s2io_ethtool_geeprom - reads the value stored in the Eeprom.
5796 * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
5797 * @eeprom : pointer to the user level structure provided by ethtool,
5798 * containing all relevant information.
5799 * @data_buf : user defined value to be written into Eeprom.
5800 * Description: Reads the values stored in the Eeprom at given offset
5801 * for a given length. Stores these values int the input argument data
5802 * buffer 'data_buf' and returns these to the caller (ethtool.)
5807 static int s2io_ethtool_geeprom(struct net_device *dev,
5808 struct ethtool_eeprom *eeprom, u8 * data_buf)
5812 struct s2io_nic *sp = netdev_priv(dev);
5814 eeprom->magic = sp->pdev->vendor | (sp->pdev->device << 16);
5816 if ((eeprom->offset + eeprom->len) > (XENA_EEPROM_SPACE))
5817 eeprom->len = XENA_EEPROM_SPACE - eeprom->offset;
5819 for (i = 0; i < eeprom->len; i += 4) {
5820 if (read_eeprom(sp, (eeprom->offset + i), &data)) {
5821 DBG_PRINT(ERR_DBG, "Read of EEPROM failed\n");
5825 memcpy((data_buf + i), &valid, 4);
5831 * s2io_ethtool_seeprom - tries to write the user provided value in Eeprom
5832 * @sp : private member of the device structure, which is a pointer to the
5833 * s2io_nic structure.
5834 * @eeprom : pointer to the user level structure provided by ethtool,
5835 * containing all relevant information.
5836 * @data_buf ; user defined value to be written into Eeprom.
5838 * Tries to write the user provided value in the Eeprom, at the offset
5839 * given by the user.
5841 * 0 on success, -EFAULT on failure.
5844 static int s2io_ethtool_seeprom(struct net_device *dev,
5845 struct ethtool_eeprom *eeprom,
5848 int len = eeprom->len, cnt = 0;
5849 u64 valid = 0, data;
5850 struct s2io_nic *sp = netdev_priv(dev);
5852 if (eeprom->magic != (sp->pdev->vendor | (sp->pdev->device << 16))) {
5854 "ETHTOOL_WRITE_EEPROM Err: "
5855 "Magic value is wrong, it is 0x%x should be 0x%x\n",
5856 (sp->pdev->vendor | (sp->pdev->device << 16)),
5862 data = (u32)data_buf[cnt] & 0x000000FF;
5864 valid = (u32)(data << 24);
5868 if (write_eeprom(sp, (eeprom->offset + cnt), valid, 0)) {
5870 "ETHTOOL_WRITE_EEPROM Err: "
5871 "Cannot write into the specified offset\n");
5882 * s2io_register_test - reads and writes into all clock domains.
5883 * @sp : private member of the device structure, which is a pointer to the
5884 * s2io_nic structure.
5885 * @data : variable that returns the result of each of the test conducted b
5888 * Read and write into all clock domains. The NIC has 3 clock domains,
5889 * see that registers in all the three regions are accessible.
5894 static int s2io_register_test(struct s2io_nic *sp, uint64_t *data)
5896 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5897 u64 val64 = 0, exp_val;
5900 val64 = readq(&bar0->pif_rd_swapper_fb);
5901 if (val64 != 0x123456789abcdefULL) {
5903 DBG_PRINT(INFO_DBG, "Read Test level %d fails\n", 1);
5906 val64 = readq(&bar0->rmac_pause_cfg);
5907 if (val64 != 0xc000ffff00000000ULL) {
5909 DBG_PRINT(INFO_DBG, "Read Test level %d fails\n", 2);
5912 val64 = readq(&bar0->rx_queue_cfg);
5913 if (sp->device_type == XFRAME_II_DEVICE)
5914 exp_val = 0x0404040404040404ULL;
5916 exp_val = 0x0808080808080808ULL;
5917 if (val64 != exp_val) {
5919 DBG_PRINT(INFO_DBG, "Read Test level %d fails\n", 3);
5922 val64 = readq(&bar0->xgxs_efifo_cfg);
5923 if (val64 != 0x000000001923141EULL) {
5925 DBG_PRINT(INFO_DBG, "Read Test level %d fails\n", 4);
5928 val64 = 0x5A5A5A5A5A5A5A5AULL;
5929 writeq(val64, &bar0->xmsi_data);
5930 val64 = readq(&bar0->xmsi_data);
5931 if (val64 != 0x5A5A5A5A5A5A5A5AULL) {
5933 DBG_PRINT(ERR_DBG, "Write Test level %d fails\n", 1);
5936 val64 = 0xA5A5A5A5A5A5A5A5ULL;
5937 writeq(val64, &bar0->xmsi_data);
5938 val64 = readq(&bar0->xmsi_data);
5939 if (val64 != 0xA5A5A5A5A5A5A5A5ULL) {
5941 DBG_PRINT(ERR_DBG, "Write Test level %d fails\n", 2);
5949 * s2io_eeprom_test - to verify that EEprom in the xena can be programmed.
5950 * @sp : private member of the device structure, which is a pointer to the
5951 * s2io_nic structure.
5952 * @data:variable that returns the result of each of the test conducted by
5955 * Verify that EEPROM in the xena can be programmed using I2C_CONTROL
5961 static int s2io_eeprom_test(struct s2io_nic *sp, uint64_t *data)
5964 u64 ret_data, org_4F0, org_7F0;
5965 u8 saved_4F0 = 0, saved_7F0 = 0;
5966 struct net_device *dev = sp->dev;
5968 /* Test Write Error at offset 0 */
5969 /* Note that SPI interface allows write access to all areas
5970 * of EEPROM. Hence doing all negative testing only for Xframe I.
5972 if (sp->device_type == XFRAME_I_DEVICE)
5973 if (!write_eeprom(sp, 0, 0, 3))
5976 /* Save current values at offsets 0x4F0 and 0x7F0 */
5977 if (!read_eeprom(sp, 0x4F0, &org_4F0))
5979 if (!read_eeprom(sp, 0x7F0, &org_7F0))
5982 /* Test Write at offset 4f0 */
5983 if (write_eeprom(sp, 0x4F0, 0x012345, 3))
5985 if (read_eeprom(sp, 0x4F0, &ret_data))
5988 if (ret_data != 0x012345) {
5989 DBG_PRINT(ERR_DBG, "%s: eeprom test error at offset 0x4F0. "
5990 "Data written %llx Data read %llx\n",
5991 dev->name, (unsigned long long)0x12345,
5992 (unsigned long long)ret_data);
5996 /* Reset the EEPROM data go FFFF */
5997 write_eeprom(sp, 0x4F0, 0xFFFFFF, 3);
5999 /* Test Write Request Error at offset 0x7c */
6000 if (sp->device_type == XFRAME_I_DEVICE)
6001 if (!write_eeprom(sp, 0x07C, 0, 3))
6004 /* Test Write Request at offset 0x7f0 */
6005 if (write_eeprom(sp, 0x7F0, 0x012345, 3))
6007 if (read_eeprom(sp, 0x7F0, &ret_data))
6010 if (ret_data != 0x012345) {
6011 DBG_PRINT(ERR_DBG, "%s: eeprom test error at offset 0x7F0. "
6012 "Data written %llx Data read %llx\n",
6013 dev->name, (unsigned long long)0x12345,
6014 (unsigned long long)ret_data);
6018 /* Reset the EEPROM data go FFFF */
6019 write_eeprom(sp, 0x7F0, 0xFFFFFF, 3);
6021 if (sp->device_type == XFRAME_I_DEVICE) {
6022 /* Test Write Error at offset 0x80 */
6023 if (!write_eeprom(sp, 0x080, 0, 3))
6026 /* Test Write Error at offset 0xfc */
6027 if (!write_eeprom(sp, 0x0FC, 0, 3))
6030 /* Test Write Error at offset 0x100 */
6031 if (!write_eeprom(sp, 0x100, 0, 3))
6034 /* Test Write Error at offset 4ec */
6035 if (!write_eeprom(sp, 0x4EC, 0, 3))
6039 /* Restore values at offsets 0x4F0 and 0x7F0 */
6041 write_eeprom(sp, 0x4F0, org_4F0, 3);
6043 write_eeprom(sp, 0x7F0, org_7F0, 3);
6050 * s2io_bist_test - invokes the MemBist test of the card .
6051 * @sp : private member of the device structure, which is a pointer to the
6052 * s2io_nic structure.
6053 * @data:variable that returns the result of each of the test conducted by
6056 * This invokes the MemBist test of the card. We give around
6057 * 2 secs time for the Test to complete. If it's still not complete
6058 * within this peiod, we consider that the test failed.
6060 * 0 on success and -1 on failure.
6063 static int s2io_bist_test(struct s2io_nic *sp, uint64_t *data)
6066 int cnt = 0, ret = -1;
6068 pci_read_config_byte(sp->pdev, PCI_BIST, &bist);
6069 bist |= PCI_BIST_START;
6070 pci_write_config_word(sp->pdev, PCI_BIST, bist);
6073 pci_read_config_byte(sp->pdev, PCI_BIST, &bist);
6074 if (!(bist & PCI_BIST_START)) {
6075 *data = (bist & PCI_BIST_CODE_MASK);
6087 * s2io_link_test - verifies the link state of the nic
6088 * @sp ; private member of the device structure, which is a pointer to the
6089 * s2io_nic structure.
6090 * @data: variable that returns the result of each of the test conducted by
6093 * The function verifies the link state of the NIC and updates the input
6094 * argument 'data' appropriately.
6099 static int s2io_link_test(struct s2io_nic *sp, uint64_t *data)
6101 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6104 val64 = readq(&bar0->adapter_status);
6105 if (!(LINK_IS_UP(val64)))
6114 * s2io_rldram_test - offline test for access to the RldRam chip on the NIC
6115 * @sp: private member of the device structure, which is a pointer to the
6116 * s2io_nic structure.
6117 * @data: variable that returns the result of each of the test
6118 * conducted by the driver.
6120 * This is one of the offline test that tests the read and write
6121 * access to the RldRam chip on the NIC.
6126 static int s2io_rldram_test(struct s2io_nic *sp, uint64_t *data)
6128 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6130 int cnt, iteration = 0, test_fail = 0;
6132 val64 = readq(&bar0->adapter_control);
6133 val64 &= ~ADAPTER_ECC_EN;
6134 writeq(val64, &bar0->adapter_control);
6136 val64 = readq(&bar0->mc_rldram_test_ctrl);
6137 val64 |= MC_RLDRAM_TEST_MODE;
6138 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
6140 val64 = readq(&bar0->mc_rldram_mrs);
6141 val64 |= MC_RLDRAM_QUEUE_SIZE_ENABLE;
6142 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
6144 val64 |= MC_RLDRAM_MRS_ENABLE;
6145 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
6147 while (iteration < 2) {
6148 val64 = 0x55555555aaaa0000ULL;
6150 val64 ^= 0xFFFFFFFFFFFF0000ULL;
6151 writeq(val64, &bar0->mc_rldram_test_d0);
6153 val64 = 0xaaaa5a5555550000ULL;
6155 val64 ^= 0xFFFFFFFFFFFF0000ULL;
6156 writeq(val64, &bar0->mc_rldram_test_d1);
6158 val64 = 0x55aaaaaaaa5a0000ULL;
6160 val64 ^= 0xFFFFFFFFFFFF0000ULL;
6161 writeq(val64, &bar0->mc_rldram_test_d2);
6163 val64 = (u64) (0x0000003ffffe0100ULL);
6164 writeq(val64, &bar0->mc_rldram_test_add);
6166 val64 = MC_RLDRAM_TEST_MODE |
6167 MC_RLDRAM_TEST_WRITE |
6169 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
6171 for (cnt = 0; cnt < 5; cnt++) {
6172 val64 = readq(&bar0->mc_rldram_test_ctrl);
6173 if (val64 & MC_RLDRAM_TEST_DONE)
6181 val64 = MC_RLDRAM_TEST_MODE | MC_RLDRAM_TEST_GO;
6182 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
6184 for (cnt = 0; cnt < 5; cnt++) {
6185 val64 = readq(&bar0->mc_rldram_test_ctrl);
6186 if (val64 & MC_RLDRAM_TEST_DONE)
6194 val64 = readq(&bar0->mc_rldram_test_ctrl);
6195 if (!(val64 & MC_RLDRAM_TEST_PASS))
6203 /* Bring the adapter out of test mode */
6204 SPECIAL_REG_WRITE(0, &bar0->mc_rldram_test_ctrl, LF);
6210 * s2io_ethtool_test - conducts 6 tsets to determine the health of card.
6211 * @sp : private member of the device structure, which is a pointer to the
6212 * s2io_nic structure.
6213 * @ethtest : pointer to a ethtool command specific structure that will be
6214 * returned to the user.
6215 * @data : variable that returns the result of each of the test
6216 * conducted by the driver.
6218 * This function conducts 6 tests ( 4 offline and 2 online) to determine
6219 * the health of the card.
6224 static void s2io_ethtool_test(struct net_device *dev,
6225 struct ethtool_test *ethtest,
6228 struct s2io_nic *sp = netdev_priv(dev);
6229 int orig_state = netif_running(sp->dev);
6231 if (ethtest->flags == ETH_TEST_FL_OFFLINE) {
6232 /* Offline Tests. */
6234 s2io_close(sp->dev);
6236 if (s2io_register_test(sp, &data[0]))
6237 ethtest->flags |= ETH_TEST_FL_FAILED;
6241 if (s2io_rldram_test(sp, &data[3]))
6242 ethtest->flags |= ETH_TEST_FL_FAILED;
6246 if (s2io_eeprom_test(sp, &data[1]))
6247 ethtest->flags |= ETH_TEST_FL_FAILED;
6249 if (s2io_bist_test(sp, &data[4]))
6250 ethtest->flags |= ETH_TEST_FL_FAILED;
6259 DBG_PRINT(ERR_DBG, "%s: is not up, cannot run test\n",
6268 if (s2io_link_test(sp, &data[2]))
6269 ethtest->flags |= ETH_TEST_FL_FAILED;
6278 static void s2io_get_ethtool_stats(struct net_device *dev,
6279 struct ethtool_stats *estats,
6283 struct s2io_nic *sp = netdev_priv(dev);
6284 struct stat_block *stats = sp->mac_control.stats_info;
6285 struct swStat *swstats = &stats->sw_stat;
6286 struct xpakStat *xstats = &stats->xpak_stat;
6288 s2io_updt_stats(sp);
6290 (u64)le32_to_cpu(stats->tmac_frms_oflow) << 32 |
6291 le32_to_cpu(stats->tmac_frms);
6293 (u64)le32_to_cpu(stats->tmac_data_octets_oflow) << 32 |
6294 le32_to_cpu(stats->tmac_data_octets);
6295 tmp_stats[i++] = le64_to_cpu(stats->tmac_drop_frms);
6297 (u64)le32_to_cpu(stats->tmac_mcst_frms_oflow) << 32 |
6298 le32_to_cpu(stats->tmac_mcst_frms);
6300 (u64)le32_to_cpu(stats->tmac_bcst_frms_oflow) << 32 |
6301 le32_to_cpu(stats->tmac_bcst_frms);
6302 tmp_stats[i++] = le64_to_cpu(stats->tmac_pause_ctrl_frms);
6304 (u64)le32_to_cpu(stats->tmac_ttl_octets_oflow) << 32 |
6305 le32_to_cpu(stats->tmac_ttl_octets);
6307 (u64)le32_to_cpu(stats->tmac_ucst_frms_oflow) << 32 |
6308 le32_to_cpu(stats->tmac_ucst_frms);
6310 (u64)le32_to_cpu(stats->tmac_nucst_frms_oflow) << 32 |
6311 le32_to_cpu(stats->tmac_nucst_frms);
6313 (u64)le32_to_cpu(stats->tmac_any_err_frms_oflow) << 32 |
6314 le32_to_cpu(stats->tmac_any_err_frms);
6315 tmp_stats[i++] = le64_to_cpu(stats->tmac_ttl_less_fb_octets);
6316 tmp_stats[i++] = le64_to_cpu(stats->tmac_vld_ip_octets);
6318 (u64)le32_to_cpu(stats->tmac_vld_ip_oflow) << 32 |
6319 le32_to_cpu(stats->tmac_vld_ip);
6321 (u64)le32_to_cpu(stats->tmac_drop_ip_oflow) << 32 |
6322 le32_to_cpu(stats->tmac_drop_ip);
6324 (u64)le32_to_cpu(stats->tmac_icmp_oflow) << 32 |
6325 le32_to_cpu(stats->tmac_icmp);
6327 (u64)le32_to_cpu(stats->tmac_rst_tcp_oflow) << 32 |
6328 le32_to_cpu(stats->tmac_rst_tcp);
6329 tmp_stats[i++] = le64_to_cpu(stats->tmac_tcp);
6330 tmp_stats[i++] = (u64)le32_to_cpu(stats->tmac_udp_oflow) << 32 |
6331 le32_to_cpu(stats->tmac_udp);
6333 (u64)le32_to_cpu(stats->rmac_vld_frms_oflow) << 32 |
6334 le32_to_cpu(stats->rmac_vld_frms);
6336 (u64)le32_to_cpu(stats->rmac_data_octets_oflow) << 32 |
6337 le32_to_cpu(stats->rmac_data_octets);
6338 tmp_stats[i++] = le64_to_cpu(stats->rmac_fcs_err_frms);
6339 tmp_stats[i++] = le64_to_cpu(stats->rmac_drop_frms);
6341 (u64)le32_to_cpu(stats->rmac_vld_mcst_frms_oflow) << 32 |
6342 le32_to_cpu(stats->rmac_vld_mcst_frms);
6344 (u64)le32_to_cpu(stats->rmac_vld_bcst_frms_oflow) << 32 |
6345 le32_to_cpu(stats->rmac_vld_bcst_frms);
6346 tmp_stats[i++] = le32_to_cpu(stats->rmac_in_rng_len_err_frms);
6347 tmp_stats[i++] = le32_to_cpu(stats->rmac_out_rng_len_err_frms);
6348 tmp_stats[i++] = le64_to_cpu(stats->rmac_long_frms);
6349 tmp_stats[i++] = le64_to_cpu(stats->rmac_pause_ctrl_frms);
6350 tmp_stats[i++] = le64_to_cpu(stats->rmac_unsup_ctrl_frms);
6352 (u64)le32_to_cpu(stats->rmac_ttl_octets_oflow) << 32 |
6353 le32_to_cpu(stats->rmac_ttl_octets);
6355 (u64)le32_to_cpu(stats->rmac_accepted_ucst_frms_oflow) << 32
6356 | le32_to_cpu(stats->rmac_accepted_ucst_frms);
6358 (u64)le32_to_cpu(stats->rmac_accepted_nucst_frms_oflow)
6359 << 32 | le32_to_cpu(stats->rmac_accepted_nucst_frms);
6361 (u64)le32_to_cpu(stats->rmac_discarded_frms_oflow) << 32 |
6362 le32_to_cpu(stats->rmac_discarded_frms);
6364 (u64)le32_to_cpu(stats->rmac_drop_events_oflow)
6365 << 32 | le32_to_cpu(stats->rmac_drop_events);
6366 tmp_stats[i++] = le64_to_cpu(stats->rmac_ttl_less_fb_octets);
6367 tmp_stats[i++] = le64_to_cpu(stats->rmac_ttl_frms);
6369 (u64)le32_to_cpu(stats->rmac_usized_frms_oflow) << 32 |
6370 le32_to_cpu(stats->rmac_usized_frms);
6372 (u64)le32_to_cpu(stats->rmac_osized_frms_oflow) << 32 |
6373 le32_to_cpu(stats->rmac_osized_frms);
6375 (u64)le32_to_cpu(stats->rmac_frag_frms_oflow) << 32 |
6376 le32_to_cpu(stats->rmac_frag_frms);
6378 (u64)le32_to_cpu(stats->rmac_jabber_frms_oflow) << 32 |
6379 le32_to_cpu(stats->rmac_jabber_frms);
6380 tmp_stats[i++] = le64_to_cpu(stats->rmac_ttl_64_frms);
6381 tmp_stats[i++] = le64_to_cpu(stats->rmac_ttl_65_127_frms);
6382 tmp_stats[i++] = le64_to_cpu(stats->rmac_ttl_128_255_frms);
6383 tmp_stats[i++] = le64_to_cpu(stats->rmac_ttl_256_511_frms);
6384 tmp_stats[i++] = le64_to_cpu(stats->rmac_ttl_512_1023_frms);
6385 tmp_stats[i++] = le64_to_cpu(stats->rmac_ttl_1024_1518_frms);
6387 (u64)le32_to_cpu(stats->rmac_ip_oflow) << 32 |
6388 le32_to_cpu(stats->rmac_ip);
6389 tmp_stats[i++] = le64_to_cpu(stats->rmac_ip_octets);
6390 tmp_stats[i++] = le32_to_cpu(stats->rmac_hdr_err_ip);
6392 (u64)le32_to_cpu(stats->rmac_drop_ip_oflow) << 32 |
6393 le32_to_cpu(stats->rmac_drop_ip);
6395 (u64)le32_to_cpu(stats->rmac_icmp_oflow) << 32 |
6396 le32_to_cpu(stats->rmac_icmp);
6397 tmp_stats[i++] = le64_to_cpu(stats->rmac_tcp);
6399 (u64)le32_to_cpu(stats->rmac_udp_oflow) << 32 |
6400 le32_to_cpu(stats->rmac_udp);
6402 (u64)le32_to_cpu(stats->rmac_err_drp_udp_oflow) << 32 |
6403 le32_to_cpu(stats->rmac_err_drp_udp);
6404 tmp_stats[i++] = le64_to_cpu(stats->rmac_xgmii_err_sym);
6405 tmp_stats[i++] = le64_to_cpu(stats->rmac_frms_q0);
6406 tmp_stats[i++] = le64_to_cpu(stats->rmac_frms_q1);
6407 tmp_stats[i++] = le64_to_cpu(stats->rmac_frms_q2);
6408 tmp_stats[i++] = le64_to_cpu(stats->rmac_frms_q3);
6409 tmp_stats[i++] = le64_to_cpu(stats->rmac_frms_q4);
6410 tmp_stats[i++] = le64_to_cpu(stats->rmac_frms_q5);
6411 tmp_stats[i++] = le64_to_cpu(stats->rmac_frms_q6);
6412 tmp_stats[i++] = le64_to_cpu(stats->rmac_frms_q7);
6413 tmp_stats[i++] = le16_to_cpu(stats->rmac_full_q0);
6414 tmp_stats[i++] = le16_to_cpu(stats->rmac_full_q1);
6415 tmp_stats[i++] = le16_to_cpu(stats->rmac_full_q2);
6416 tmp_stats[i++] = le16_to_cpu(stats->rmac_full_q3);
6417 tmp_stats[i++] = le16_to_cpu(stats->rmac_full_q4);
6418 tmp_stats[i++] = le16_to_cpu(stats->rmac_full_q5);
6419 tmp_stats[i++] = le16_to_cpu(stats->rmac_full_q6);
6420 tmp_stats[i++] = le16_to_cpu(stats->rmac_full_q7);
6422 (u64)le32_to_cpu(stats->rmac_pause_cnt_oflow) << 32 |
6423 le32_to_cpu(stats->rmac_pause_cnt);
6424 tmp_stats[i++] = le64_to_cpu(stats->rmac_xgmii_data_err_cnt);
6425 tmp_stats[i++] = le64_to_cpu(stats->rmac_xgmii_ctrl_err_cnt);
6427 (u64)le32_to_cpu(stats->rmac_accepted_ip_oflow) << 32 |
6428 le32_to_cpu(stats->rmac_accepted_ip);
6429 tmp_stats[i++] = le32_to_cpu(stats->rmac_err_tcp);
6430 tmp_stats[i++] = le32_to_cpu(stats->rd_req_cnt);
6431 tmp_stats[i++] = le32_to_cpu(stats->new_rd_req_cnt);
6432 tmp_stats[i++] = le32_to_cpu(stats->new_rd_req_rtry_cnt);
6433 tmp_stats[i++] = le32_to_cpu(stats->rd_rtry_cnt);
6434 tmp_stats[i++] = le32_to_cpu(stats->wr_rtry_rd_ack_cnt);
6435 tmp_stats[i++] = le32_to_cpu(stats->wr_req_cnt);
6436 tmp_stats[i++] = le32_to_cpu(stats->new_wr_req_cnt);
6437 tmp_stats[i++] = le32_to_cpu(stats->new_wr_req_rtry_cnt);
6438 tmp_stats[i++] = le32_to_cpu(stats->wr_rtry_cnt);
6439 tmp_stats[i++] = le32_to_cpu(stats->wr_disc_cnt);
6440 tmp_stats[i++] = le32_to_cpu(stats->rd_rtry_wr_ack_cnt);
6441 tmp_stats[i++] = le32_to_cpu(stats->txp_wr_cnt);
6442 tmp_stats[i++] = le32_to_cpu(stats->txd_rd_cnt);
6443 tmp_stats[i++] = le32_to_cpu(stats->txd_wr_cnt);
6444 tmp_stats[i++] = le32_to_cpu(stats->rxd_rd_cnt);
6445 tmp_stats[i++] = le32_to_cpu(stats->rxd_wr_cnt);
6446 tmp_stats[i++] = le32_to_cpu(stats->txf_rd_cnt);
6447 tmp_stats[i++] = le32_to_cpu(stats->rxf_wr_cnt);
6449 /* Enhanced statistics exist only for Hercules */
6450 if (sp->device_type == XFRAME_II_DEVICE) {
6452 le64_to_cpu(stats->rmac_ttl_1519_4095_frms);
6454 le64_to_cpu(stats->rmac_ttl_4096_8191_frms);
6456 le64_to_cpu(stats->rmac_ttl_8192_max_frms);
6457 tmp_stats[i++] = le64_to_cpu(stats->rmac_ttl_gt_max_frms);
6458 tmp_stats[i++] = le64_to_cpu(stats->rmac_osized_alt_frms);
6459 tmp_stats[i++] = le64_to_cpu(stats->rmac_jabber_alt_frms);
6460 tmp_stats[i++] = le64_to_cpu(stats->rmac_gt_max_alt_frms);
6461 tmp_stats[i++] = le64_to_cpu(stats->rmac_vlan_frms);
6462 tmp_stats[i++] = le32_to_cpu(stats->rmac_len_discard);
6463 tmp_stats[i++] = le32_to_cpu(stats->rmac_fcs_discard);
6464 tmp_stats[i++] = le32_to_cpu(stats->rmac_pf_discard);
6465 tmp_stats[i++] = le32_to_cpu(stats->rmac_da_discard);
6466 tmp_stats[i++] = le32_to_cpu(stats->rmac_red_discard);
6467 tmp_stats[i++] = le32_to_cpu(stats->rmac_rts_discard);
6468 tmp_stats[i++] = le32_to_cpu(stats->rmac_ingm_full_discard);
6469 tmp_stats[i++] = le32_to_cpu(stats->link_fault_cnt);
6473 tmp_stats[i++] = swstats->single_ecc_errs;
6474 tmp_stats[i++] = swstats->double_ecc_errs;
6475 tmp_stats[i++] = swstats->parity_err_cnt;
6476 tmp_stats[i++] = swstats->serious_err_cnt;
6477 tmp_stats[i++] = swstats->soft_reset_cnt;
6478 tmp_stats[i++] = swstats->fifo_full_cnt;
6479 for (k = 0; k < MAX_RX_RINGS; k++)
6480 tmp_stats[i++] = swstats->ring_full_cnt[k];
6481 tmp_stats[i++] = xstats->alarm_transceiver_temp_high;
6482 tmp_stats[i++] = xstats->alarm_transceiver_temp_low;
6483 tmp_stats[i++] = xstats->alarm_laser_bias_current_high;
6484 tmp_stats[i++] = xstats->alarm_laser_bias_current_low;
6485 tmp_stats[i++] = xstats->alarm_laser_output_power_high;
6486 tmp_stats[i++] = xstats->alarm_laser_output_power_low;
6487 tmp_stats[i++] = xstats->warn_transceiver_temp_high;
6488 tmp_stats[i++] = xstats->warn_transceiver_temp_low;
6489 tmp_stats[i++] = xstats->warn_laser_bias_current_high;
6490 tmp_stats[i++] = xstats->warn_laser_bias_current_low;
6491 tmp_stats[i++] = xstats->warn_laser_output_power_high;
6492 tmp_stats[i++] = xstats->warn_laser_output_power_low;
6493 tmp_stats[i++] = swstats->clubbed_frms_cnt;
6494 tmp_stats[i++] = swstats->sending_both;
6495 tmp_stats[i++] = swstats->outof_sequence_pkts;
6496 tmp_stats[i++] = swstats->flush_max_pkts;
6497 if (swstats->num_aggregations) {
6498 u64 tmp = swstats->sum_avg_pkts_aggregated;
6501 * Since 64-bit divide does not work on all platforms,
6502 * do repeated subtraction.
6504 while (tmp >= swstats->num_aggregations) {
6505 tmp -= swstats->num_aggregations;
6508 tmp_stats[i++] = count;
6511 tmp_stats[i++] = swstats->mem_alloc_fail_cnt;
6512 tmp_stats[i++] = swstats->pci_map_fail_cnt;
6513 tmp_stats[i++] = swstats->watchdog_timer_cnt;
6514 tmp_stats[i++] = swstats->mem_allocated;
6515 tmp_stats[i++] = swstats->mem_freed;
6516 tmp_stats[i++] = swstats->link_up_cnt;
6517 tmp_stats[i++] = swstats->link_down_cnt;
6518 tmp_stats[i++] = swstats->link_up_time;
6519 tmp_stats[i++] = swstats->link_down_time;
6521 tmp_stats[i++] = swstats->tx_buf_abort_cnt;
6522 tmp_stats[i++] = swstats->tx_desc_abort_cnt;
6523 tmp_stats[i++] = swstats->tx_parity_err_cnt;
6524 tmp_stats[i++] = swstats->tx_link_loss_cnt;
6525 tmp_stats[i++] = swstats->tx_list_proc_err_cnt;
6527 tmp_stats[i++] = swstats->rx_parity_err_cnt;
6528 tmp_stats[i++] = swstats->rx_abort_cnt;
6529 tmp_stats[i++] = swstats->rx_parity_abort_cnt;
6530 tmp_stats[i++] = swstats->rx_rda_fail_cnt;
6531 tmp_stats[i++] = swstats->rx_unkn_prot_cnt;
6532 tmp_stats[i++] = swstats->rx_fcs_err_cnt;
6533 tmp_stats[i++] = swstats->rx_buf_size_err_cnt;
6534 tmp_stats[i++] = swstats->rx_rxd_corrupt_cnt;
6535 tmp_stats[i++] = swstats->rx_unkn_err_cnt;
6536 tmp_stats[i++] = swstats->tda_err_cnt;
6537 tmp_stats[i++] = swstats->pfc_err_cnt;
6538 tmp_stats[i++] = swstats->pcc_err_cnt;
6539 tmp_stats[i++] = swstats->tti_err_cnt;
6540 tmp_stats[i++] = swstats->tpa_err_cnt;
6541 tmp_stats[i++] = swstats->sm_err_cnt;
6542 tmp_stats[i++] = swstats->lso_err_cnt;
6543 tmp_stats[i++] = swstats->mac_tmac_err_cnt;
6544 tmp_stats[i++] = swstats->mac_rmac_err_cnt;
6545 tmp_stats[i++] = swstats->xgxs_txgxs_err_cnt;
6546 tmp_stats[i++] = swstats->xgxs_rxgxs_err_cnt;
6547 tmp_stats[i++] = swstats->rc_err_cnt;
6548 tmp_stats[i++] = swstats->prc_pcix_err_cnt;
6549 tmp_stats[i++] = swstats->rpa_err_cnt;
6550 tmp_stats[i++] = swstats->rda_err_cnt;
6551 tmp_stats[i++] = swstats->rti_err_cnt;
6552 tmp_stats[i++] = swstats->mc_err_cnt;
6555 static int s2io_ethtool_get_regs_len(struct net_device *dev)
6557 return XENA_REG_SPACE;
6561 static int s2io_get_eeprom_len(struct net_device *dev)
6563 return XENA_EEPROM_SPACE;
6566 static int s2io_get_sset_count(struct net_device *dev, int sset)
6568 struct s2io_nic *sp = netdev_priv(dev);
6572 return S2IO_TEST_LEN;
6574 switch (sp->device_type) {
6575 case XFRAME_I_DEVICE:
6576 return XFRAME_I_STAT_LEN;
6577 case XFRAME_II_DEVICE:
6578 return XFRAME_II_STAT_LEN;
6587 static void s2io_ethtool_get_strings(struct net_device *dev,
6588 u32 stringset, u8 *data)
6591 struct s2io_nic *sp = netdev_priv(dev);
6593 switch (stringset) {
6595 memcpy(data, s2io_gstrings, S2IO_STRINGS_LEN);
6598 stat_size = sizeof(ethtool_xena_stats_keys);
6599 memcpy(data, ðtool_xena_stats_keys, stat_size);
6600 if (sp->device_type == XFRAME_II_DEVICE) {
6601 memcpy(data + stat_size,
6602 ðtool_enhanced_stats_keys,
6603 sizeof(ethtool_enhanced_stats_keys));
6604 stat_size += sizeof(ethtool_enhanced_stats_keys);
6607 memcpy(data + stat_size, ðtool_driver_stats_keys,
6608 sizeof(ethtool_driver_stats_keys));
6612 static int s2io_set_features(struct net_device *dev, netdev_features_t features)
6614 struct s2io_nic *sp = netdev_priv(dev);
6615 netdev_features_t changed = (features ^ dev->features) & NETIF_F_LRO;
6617 if (changed && netif_running(dev)) {
6620 s2io_stop_all_tx_queue(sp);
6622 dev->features = features;
6623 rc = s2io_card_up(sp);
6627 s2io_start_all_tx_queue(sp);
6635 static const struct ethtool_ops netdev_ethtool_ops = {
6636 .get_settings = s2io_ethtool_gset,
6637 .set_settings = s2io_ethtool_sset,
6638 .get_drvinfo = s2io_ethtool_gdrvinfo,
6639 .get_regs_len = s2io_ethtool_get_regs_len,
6640 .get_regs = s2io_ethtool_gregs,
6641 .get_link = ethtool_op_get_link,
6642 .get_eeprom_len = s2io_get_eeprom_len,
6643 .get_eeprom = s2io_ethtool_geeprom,
6644 .set_eeprom = s2io_ethtool_seeprom,
6645 .get_ringparam = s2io_ethtool_gringparam,
6646 .get_pauseparam = s2io_ethtool_getpause_data,
6647 .set_pauseparam = s2io_ethtool_setpause_data,
6648 .self_test = s2io_ethtool_test,
6649 .get_strings = s2io_ethtool_get_strings,
6650 .set_phys_id = s2io_ethtool_set_led,
6651 .get_ethtool_stats = s2io_get_ethtool_stats,
6652 .get_sset_count = s2io_get_sset_count,
6656 * s2io_ioctl - Entry point for the Ioctl
6657 * @dev : Device pointer.
6658 * @ifr : An IOCTL specefic structure, that can contain a pointer to
6659 * a proprietary structure used to pass information to the driver.
6660 * @cmd : This is used to distinguish between the different commands that
6661 * can be passed to the IOCTL functions.
6663 * Currently there are no special functionality supported in IOCTL, hence
6664 * function always return EOPNOTSUPPORTED
6667 static int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
6673 * s2io_change_mtu - entry point to change MTU size for the device.
6674 * @dev : device pointer.
6675 * @new_mtu : the new MTU size for the device.
6676 * Description: A driver entry point to change MTU size for the device.
6677 * Before changing the MTU the device must be stopped.
6679 * 0 on success and an appropriate (-)ve integer as defined in errno.h
6683 static int s2io_change_mtu(struct net_device *dev, int new_mtu)
6685 struct s2io_nic *sp = netdev_priv(dev);
6688 if ((new_mtu < MIN_MTU) || (new_mtu > S2IO_JUMBO_SIZE)) {
6689 DBG_PRINT(ERR_DBG, "%s: MTU size is invalid.\n", dev->name);
6694 if (netif_running(dev)) {
6695 s2io_stop_all_tx_queue(sp);
6697 ret = s2io_card_up(sp);
6699 DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
6703 s2io_wake_all_tx_queue(sp);
6704 } else { /* Device is down */
6705 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6706 u64 val64 = new_mtu;
6708 writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
6715 * s2io_set_link - Set the LInk status
6716 * @data: long pointer to device private structue
6717 * Description: Sets the link status for the adapter
6720 static void s2io_set_link(struct work_struct *work)
6722 struct s2io_nic *nic = container_of(work, struct s2io_nic,
6724 struct net_device *dev = nic->dev;
6725 struct XENA_dev_config __iomem *bar0 = nic->bar0;
6731 if (!netif_running(dev))
6734 if (test_and_set_bit(__S2IO_STATE_LINK_TASK, &(nic->state))) {
6735 /* The card is being reset, no point doing anything */
6739 subid = nic->pdev->subsystem_device;
6740 if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
6742 * Allow a small delay for the NICs self initiated
6743 * cleanup to complete.
6748 val64 = readq(&bar0->adapter_status);
6749 if (LINK_IS_UP(val64)) {
6750 if (!(readq(&bar0->adapter_control) & ADAPTER_CNTL_EN)) {
6751 if (verify_xena_quiescence(nic)) {
6752 val64 = readq(&bar0->adapter_control);
6753 val64 |= ADAPTER_CNTL_EN;
6754 writeq(val64, &bar0->adapter_control);
6755 if (CARDS_WITH_FAULTY_LINK_INDICATORS(
6756 nic->device_type, subid)) {
6757 val64 = readq(&bar0->gpio_control);
6758 val64 |= GPIO_CTRL_GPIO_0;
6759 writeq(val64, &bar0->gpio_control);
6760 val64 = readq(&bar0->gpio_control);
6762 val64 |= ADAPTER_LED_ON;
6763 writeq(val64, &bar0->adapter_control);
6765 nic->device_enabled_once = true;
6768 "%s: Error: device is not Quiescent\n",
6770 s2io_stop_all_tx_queue(nic);
6773 val64 = readq(&bar0->adapter_control);
6774 val64 |= ADAPTER_LED_ON;
6775 writeq(val64, &bar0->adapter_control);
6776 s2io_link(nic, LINK_UP);
6778 if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
6780 val64 = readq(&bar0->gpio_control);
6781 val64 &= ~GPIO_CTRL_GPIO_0;
6782 writeq(val64, &bar0->gpio_control);
6783 val64 = readq(&bar0->gpio_control);
6786 val64 = readq(&bar0->adapter_control);
6787 val64 = val64 & (~ADAPTER_LED_ON);
6788 writeq(val64, &bar0->adapter_control);
6789 s2io_link(nic, LINK_DOWN);
6791 clear_bit(__S2IO_STATE_LINK_TASK, &(nic->state));
6797 static int set_rxd_buffer_pointer(struct s2io_nic *sp, struct RxD_t *rxdp,
6799 struct sk_buff **skb, u64 *temp0, u64 *temp1,
6800 u64 *temp2, int size)
6802 struct net_device *dev = sp->dev;
6803 struct swStat *stats = &sp->mac_control.stats_info->sw_stat;
6805 if ((sp->rxd_mode == RXD_MODE_1) && (rxdp->Host_Control == 0)) {
6806 struct RxD1 *rxdp1 = (struct RxD1 *)rxdp;
6809 DBG_PRINT(INFO_DBG, "SKB is not NULL\n");
6811 * As Rx frame are not going to be processed,
6812 * using same mapped address for the Rxd
6815 rxdp1->Buffer0_ptr = *temp0;
6817 *skb = netdev_alloc_skb(dev, size);
6820 "%s: Out of memory to allocate %s\n",
6821 dev->name, "1 buf mode SKBs");
6822 stats->mem_alloc_fail_cnt++;
6825 stats->mem_allocated += (*skb)->truesize;
6826 /* storing the mapped addr in a temp variable
6827 * such it will be used for next rxd whose
6828 * Host Control is NULL
6830 rxdp1->Buffer0_ptr = *temp0 =
6831 pci_map_single(sp->pdev, (*skb)->data,
6832 size - NET_IP_ALIGN,
6833 PCI_DMA_FROMDEVICE);
6834 if (pci_dma_mapping_error(sp->pdev, rxdp1->Buffer0_ptr))
6835 goto memalloc_failed;
6836 rxdp->Host_Control = (unsigned long) (*skb);
6838 } else if ((sp->rxd_mode == RXD_MODE_3B) && (rxdp->Host_Control == 0)) {
6839 struct RxD3 *rxdp3 = (struct RxD3 *)rxdp;
6840 /* Two buffer Mode */
6842 rxdp3->Buffer2_ptr = *temp2;
6843 rxdp3->Buffer0_ptr = *temp0;
6844 rxdp3->Buffer1_ptr = *temp1;
6846 *skb = netdev_alloc_skb(dev, size);
6849 "%s: Out of memory to allocate %s\n",
6852 stats->mem_alloc_fail_cnt++;
6855 stats->mem_allocated += (*skb)->truesize;
6856 rxdp3->Buffer2_ptr = *temp2 =
6857 pci_map_single(sp->pdev, (*skb)->data,
6859 PCI_DMA_FROMDEVICE);
6860 if (pci_dma_mapping_error(sp->pdev, rxdp3->Buffer2_ptr))
6861 goto memalloc_failed;
6862 rxdp3->Buffer0_ptr = *temp0 =
6863 pci_map_single(sp->pdev, ba->ba_0, BUF0_LEN,
6864 PCI_DMA_FROMDEVICE);
6865 if (pci_dma_mapping_error(sp->pdev,
6866 rxdp3->Buffer0_ptr)) {
6867 pci_unmap_single(sp->pdev,
6868 (dma_addr_t)rxdp3->Buffer2_ptr,
6870 PCI_DMA_FROMDEVICE);
6871 goto memalloc_failed;
6873 rxdp->Host_Control = (unsigned long) (*skb);
6875 /* Buffer-1 will be dummy buffer not used */
6876 rxdp3->Buffer1_ptr = *temp1 =
6877 pci_map_single(sp->pdev, ba->ba_1, BUF1_LEN,
6878 PCI_DMA_FROMDEVICE);
6879 if (pci_dma_mapping_error(sp->pdev,
6880 rxdp3->Buffer1_ptr)) {
6881 pci_unmap_single(sp->pdev,
6882 (dma_addr_t)rxdp3->Buffer0_ptr,
6883 BUF0_LEN, PCI_DMA_FROMDEVICE);
6884 pci_unmap_single(sp->pdev,
6885 (dma_addr_t)rxdp3->Buffer2_ptr,
6887 PCI_DMA_FROMDEVICE);
6888 goto memalloc_failed;
6895 stats->pci_map_fail_cnt++;
6896 stats->mem_freed += (*skb)->truesize;
6897 dev_kfree_skb(*skb);
6901 static void set_rxd_buffer_size(struct s2io_nic *sp, struct RxD_t *rxdp,
6904 struct net_device *dev = sp->dev;
6905 if (sp->rxd_mode == RXD_MODE_1) {
6906 rxdp->Control_2 = SET_BUFFER0_SIZE_1(size - NET_IP_ALIGN);
6907 } else if (sp->rxd_mode == RXD_MODE_3B) {
6908 rxdp->Control_2 = SET_BUFFER0_SIZE_3(BUF0_LEN);
6909 rxdp->Control_2 |= SET_BUFFER1_SIZE_3(1);
6910 rxdp->Control_2 |= SET_BUFFER2_SIZE_3(dev->mtu + 4);
6914 static int rxd_owner_bit_reset(struct s2io_nic *sp)
6916 int i, j, k, blk_cnt = 0, size;
6917 struct config_param *config = &sp->config;
6918 struct mac_info *mac_control = &sp->mac_control;
6919 struct net_device *dev = sp->dev;
6920 struct RxD_t *rxdp = NULL;
6921 struct sk_buff *skb = NULL;
6922 struct buffAdd *ba = NULL;
6923 u64 temp0_64 = 0, temp1_64 = 0, temp2_64 = 0;
6925 /* Calculate the size based on ring mode */
6926 size = dev->mtu + HEADER_ETHERNET_II_802_3_SIZE +
6927 HEADER_802_2_SIZE + HEADER_SNAP_SIZE;
6928 if (sp->rxd_mode == RXD_MODE_1)
6929 size += NET_IP_ALIGN;
6930 else if (sp->rxd_mode == RXD_MODE_3B)
6931 size = dev->mtu + ALIGN_SIZE + BUF0_LEN + 4;
6933 for (i = 0; i < config->rx_ring_num; i++) {
6934 struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
6935 struct ring_info *ring = &mac_control->rings[i];
6937 blk_cnt = rx_cfg->num_rxd / (rxd_count[sp->rxd_mode] + 1);
6939 for (j = 0; j < blk_cnt; j++) {
6940 for (k = 0; k < rxd_count[sp->rxd_mode]; k++) {
6941 rxdp = ring->rx_blocks[j].rxds[k].virt_addr;
6942 if (sp->rxd_mode == RXD_MODE_3B)
6943 ba = &ring->ba[j][k];
6944 if (set_rxd_buffer_pointer(sp, rxdp, ba, &skb,
6952 set_rxd_buffer_size(sp, rxdp, size);
6954 /* flip the Ownership bit to Hardware */
6955 rxdp->Control_1 |= RXD_OWN_XENA;
6963 static int s2io_add_isr(struct s2io_nic *sp)
6966 struct net_device *dev = sp->dev;
6969 if (sp->config.intr_type == MSI_X)
6970 ret = s2io_enable_msi_x(sp);
6972 DBG_PRINT(ERR_DBG, "%s: Defaulting to INTA\n", dev->name);
6973 sp->config.intr_type = INTA;
6977 * Store the values of the MSIX table in
6978 * the struct s2io_nic structure
6980 store_xmsi_data(sp);
6982 /* After proper initialization of H/W, register ISR */
6983 if (sp->config.intr_type == MSI_X) {
6984 int i, msix_rx_cnt = 0;
6986 for (i = 0; i < sp->num_entries; i++) {
6987 if (sp->s2io_entries[i].in_use == MSIX_FLG) {
6988 if (sp->s2io_entries[i].type ==
6990 sprintf(sp->desc[i], "%s:MSI-X-%d-RX",
6992 err = request_irq(sp->entries[i].vector,
6993 s2io_msix_ring_handle,
6996 sp->s2io_entries[i].arg);
6997 } else if (sp->s2io_entries[i].type ==
6999 sprintf(sp->desc[i], "%s:MSI-X-%d-TX",
7001 err = request_irq(sp->entries[i].vector,
7002 s2io_msix_fifo_handle,
7005 sp->s2io_entries[i].arg);
7008 /* if either data or addr is zero print it. */
7009 if (!(sp->msix_info[i].addr &&
7010 sp->msix_info[i].data)) {
7012 "%s @Addr:0x%llx Data:0x%llx\n",
7014 (unsigned long long)
7015 sp->msix_info[i].addr,
7016 (unsigned long long)
7017 ntohl(sp->msix_info[i].data));
7021 remove_msix_isr(sp);
7024 "%s:MSI-X-%d registration "
7025 "failed\n", dev->name, i);
7028 "%s: Defaulting to INTA\n",
7030 sp->config.intr_type = INTA;
7033 sp->s2io_entries[i].in_use =
7034 MSIX_REGISTERED_SUCCESS;
7038 pr_info("MSI-X-RX %d entries enabled\n", --msix_rx_cnt);
7040 "MSI-X-TX entries enabled through alarm vector\n");
7043 if (sp->config.intr_type == INTA) {
7044 err = request_irq(sp->pdev->irq, s2io_isr, IRQF_SHARED,
7047 DBG_PRINT(ERR_DBG, "%s: ISR registration failed\n",
7055 static void s2io_rem_isr(struct s2io_nic *sp)
7057 if (sp->config.intr_type == MSI_X)
7058 remove_msix_isr(sp);
7060 remove_inta_isr(sp);
7063 static void do_s2io_card_down(struct s2io_nic *sp, int do_io)
7066 struct XENA_dev_config __iomem *bar0 = sp->bar0;
7067 register u64 val64 = 0;
7068 struct config_param *config;
7069 config = &sp->config;
7071 if (!is_s2io_card_up(sp))
7074 del_timer_sync(&sp->alarm_timer);
7075 /* If s2io_set_link task is executing, wait till it completes. */
7076 while (test_and_set_bit(__S2IO_STATE_LINK_TASK, &(sp->state)))
7078 clear_bit(__S2IO_STATE_CARD_UP, &sp->state);
7081 if (sp->config.napi) {
7083 if (config->intr_type == MSI_X) {
7084 for (; off < sp->config.rx_ring_num; off++)
7085 napi_disable(&sp->mac_control.rings[off].napi);
7088 napi_disable(&sp->napi);
7091 /* disable Tx and Rx traffic on the NIC */
7097 /* stop the tx queue, indicate link down */
7098 s2io_link(sp, LINK_DOWN);
7100 /* Check if the device is Quiescent and then Reset the NIC */
7102 /* As per the HW requirement we need to replenish the
7103 * receive buffer to avoid the ring bump. Since there is
7104 * no intention of processing the Rx frame at this pointwe are
7105 * just setting the ownership bit of rxd in Each Rx
7106 * ring to HW and set the appropriate buffer size
7107 * based on the ring mode
7109 rxd_owner_bit_reset(sp);
7111 val64 = readq(&bar0->adapter_status);
7112 if (verify_xena_quiescence(sp)) {
7113 if (verify_pcc_quiescent(sp, sp->device_enabled_once))
7120 DBG_PRINT(ERR_DBG, "Device not Quiescent - "
7121 "adapter status reads 0x%llx\n",
7122 (unsigned long long)val64);
7129 /* Free all Tx buffers */
7130 free_tx_buffers(sp);
7132 /* Free all Rx buffers */
7133 free_rx_buffers(sp);
7135 clear_bit(__S2IO_STATE_LINK_TASK, &(sp->state));
7138 static void s2io_card_down(struct s2io_nic *sp)
7140 do_s2io_card_down(sp, 1);
7143 static int s2io_card_up(struct s2io_nic *sp)
7146 struct config_param *config;
7147 struct mac_info *mac_control;
7148 struct net_device *dev = sp->dev;
7151 /* Initialize the H/W I/O registers */
7154 DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
7162 * Initializing the Rx buffers. For now we are considering only 1
7163 * Rx ring and initializing buffers into 30 Rx blocks
7165 config = &sp->config;
7166 mac_control = &sp->mac_control;
7168 for (i = 0; i < config->rx_ring_num; i++) {
7169 struct ring_info *ring = &mac_control->rings[i];
7171 ring->mtu = dev->mtu;
7172 ring->lro = !!(dev->features & NETIF_F_LRO);
7173 ret = fill_rx_buffers(sp, ring, 1);
7175 DBG_PRINT(ERR_DBG, "%s: Out of memory in Open\n",
7178 free_rx_buffers(sp);
7181 DBG_PRINT(INFO_DBG, "Buf in ring:%d is %d:\n", i,
7182 ring->rx_bufs_left);
7185 /* Initialise napi */
7187 if (config->intr_type == MSI_X) {
7188 for (i = 0; i < sp->config.rx_ring_num; i++)
7189 napi_enable(&sp->mac_control.rings[i].napi);
7191 napi_enable(&sp->napi);
7195 /* Maintain the state prior to the open */
7196 if (sp->promisc_flg)
7197 sp->promisc_flg = 0;
7198 if (sp->m_cast_flg) {
7200 sp->all_multi_pos = 0;
7203 /* Setting its receive mode */
7204 s2io_set_multicast(dev);
7206 if (dev->features & NETIF_F_LRO) {
7207 /* Initialize max aggregatable pkts per session based on MTU */
7208 sp->lro_max_aggr_per_sess = ((1<<16) - 1) / dev->mtu;
7209 /* Check if we can use (if specified) user provided value */
7210 if (lro_max_pkts < sp->lro_max_aggr_per_sess)
7211 sp->lro_max_aggr_per_sess = lro_max_pkts;
7214 /* Enable Rx Traffic and interrupts on the NIC */
7215 if (start_nic(sp)) {
7216 DBG_PRINT(ERR_DBG, "%s: Starting NIC failed\n", dev->name);
7218 free_rx_buffers(sp);
7222 /* Add interrupt service routine */
7223 if (s2io_add_isr(sp) != 0) {
7224 if (sp->config.intr_type == MSI_X)
7227 free_rx_buffers(sp);
7231 S2IO_TIMER_CONF(sp->alarm_timer, s2io_alarm_handle, sp, (HZ/2));
7233 set_bit(__S2IO_STATE_CARD_UP, &sp->state);
7235 /* Enable select interrupts */
7236 en_dis_err_alarms(sp, ENA_ALL_INTRS, ENABLE_INTRS);
7237 if (sp->config.intr_type != INTA) {
7238 interruptible = TX_TRAFFIC_INTR | TX_PIC_INTR;
7239 en_dis_able_nic_intrs(sp, interruptible, ENABLE_INTRS);
7241 interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
7242 interruptible |= TX_PIC_INTR;
7243 en_dis_able_nic_intrs(sp, interruptible, ENABLE_INTRS);
7250 * s2io_restart_nic - Resets the NIC.
7251 * @data : long pointer to the device private structure
7253 * This function is scheduled to be run by the s2io_tx_watchdog
7254 * function after 0.5 secs to reset the NIC. The idea is to reduce
7255 * the run time of the watch dog routine which is run holding a
7259 static void s2io_restart_nic(struct work_struct *work)
7261 struct s2io_nic *sp = container_of(work, struct s2io_nic, rst_timer_task);
7262 struct net_device *dev = sp->dev;
7266 if (!netif_running(dev))
7270 if (s2io_card_up(sp)) {
7271 DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n", dev->name);
7273 s2io_wake_all_tx_queue(sp);
7274 DBG_PRINT(ERR_DBG, "%s: was reset by Tx watchdog timer\n", dev->name);
7280 * s2io_tx_watchdog - Watchdog for transmit side.
7281 * @dev : Pointer to net device structure
7283 * This function is triggered if the Tx Queue is stopped
7284 * for a pre-defined amount of time when the Interface is still up.
7285 * If the Interface is jammed in such a situation, the hardware is
7286 * reset (by s2io_close) and restarted again (by s2io_open) to
7287 * overcome any problem that might have been caused in the hardware.
7292 static void s2io_tx_watchdog(struct net_device *dev)
7294 struct s2io_nic *sp = netdev_priv(dev);
7295 struct swStat *swstats = &sp->mac_control.stats_info->sw_stat;
7297 if (netif_carrier_ok(dev)) {
7298 swstats->watchdog_timer_cnt++;
7299 schedule_work(&sp->rst_timer_task);
7300 swstats->soft_reset_cnt++;
7305 * rx_osm_handler - To perform some OS related operations on SKB.
7306 * @sp: private member of the device structure,pointer to s2io_nic structure.
7307 * @skb : the socket buffer pointer.
7308 * @len : length of the packet
7309 * @cksum : FCS checksum of the frame.
7310 * @ring_no : the ring from which this RxD was extracted.
7312 * This function is called by the Rx interrupt serivce routine to perform
7313 * some OS related operations on the SKB before passing it to the upper
7314 * layers. It mainly checks if the checksum is OK, if so adds it to the
7315 * SKBs cksum variable, increments the Rx packet count and passes the SKB
7316 * to the upper layer. If the checksum is wrong, it increments the Rx
7317 * packet error count, frees the SKB and returns error.
7319 * SUCCESS on success and -1 on failure.
7321 static int rx_osm_handler(struct ring_info *ring_data, struct RxD_t * rxdp)
7323 struct s2io_nic *sp = ring_data->nic;
7324 struct net_device *dev = ring_data->dev;
7325 struct sk_buff *skb = (struct sk_buff *)
7326 ((unsigned long)rxdp->Host_Control);
7327 int ring_no = ring_data->ring_no;
7328 u16 l3_csum, l4_csum;
7329 unsigned long long err = rxdp->Control_1 & RXD_T_CODE;
7330 struct lro *uninitialized_var(lro);
7332 struct swStat *swstats = &sp->mac_control.stats_info->sw_stat;
7337 /* Check for parity error */
7339 swstats->parity_err_cnt++;
7341 err_mask = err >> 48;
7344 swstats->rx_parity_err_cnt++;
7348 swstats->rx_abort_cnt++;
7352 swstats->rx_parity_abort_cnt++;
7356 swstats->rx_rda_fail_cnt++;
7360 swstats->rx_unkn_prot_cnt++;
7364 swstats->rx_fcs_err_cnt++;
7368 swstats->rx_buf_size_err_cnt++;
7372 swstats->rx_rxd_corrupt_cnt++;
7376 swstats->rx_unkn_err_cnt++;
7380 * Drop the packet if bad transfer code. Exception being
7381 * 0x5, which could be due to unsupported IPv6 extension header.
7382 * In this case, we let stack handle the packet.
7383 * Note that in this case, since checksum will be incorrect,
7384 * stack will validate the same.
7386 if (err_mask != 0x5) {
7387 DBG_PRINT(ERR_DBG, "%s: Rx error Value: 0x%x\n",
7388 dev->name, err_mask);
7389 dev->stats.rx_crc_errors++;
7393 ring_data->rx_bufs_left -= 1;
7394 rxdp->Host_Control = 0;
7399 rxdp->Host_Control = 0;
7400 if (sp->rxd_mode == RXD_MODE_1) {
7401 int len = RXD_GET_BUFFER0_SIZE_1(rxdp->Control_2);
7404 } else if (sp->rxd_mode == RXD_MODE_3B) {
7405 int get_block = ring_data->rx_curr_get_info.block_index;
7406 int get_off = ring_data->rx_curr_get_info.offset;
7407 int buf0_len = RXD_GET_BUFFER0_SIZE_3(rxdp->Control_2);
7408 int buf2_len = RXD_GET_BUFFER2_SIZE_3(rxdp->Control_2);
7409 unsigned char *buff = skb_push(skb, buf0_len);
7411 struct buffAdd *ba = &ring_data->ba[get_block][get_off];
7412 memcpy(buff, ba->ba_0, buf0_len);
7413 skb_put(skb, buf2_len);
7416 if ((rxdp->Control_1 & TCP_OR_UDP_FRAME) &&
7417 ((!ring_data->lro) ||
7418 (ring_data->lro && (!(rxdp->Control_1 & RXD_FRAME_IP_FRAG)))) &&
7419 (dev->features & NETIF_F_RXCSUM)) {
7420 l3_csum = RXD_GET_L3_CKSUM(rxdp->Control_1);
7421 l4_csum = RXD_GET_L4_CKSUM(rxdp->Control_1);
7422 if ((l3_csum == L3_CKSUM_OK) && (l4_csum == L4_CKSUM_OK)) {
7424 * NIC verifies if the Checksum of the received
7425 * frame is Ok or not and accordingly returns
7426 * a flag in the RxD.
7428 skb->ip_summed = CHECKSUM_UNNECESSARY;
7429 if (ring_data->lro) {
7434 ret = s2io_club_tcp_session(ring_data,
7439 case 3: /* Begin anew */
7442 case 1: /* Aggregate */
7443 lro_append_pkt(sp, lro, skb, tcp_len);
7445 case 4: /* Flush session */
7446 lro_append_pkt(sp, lro, skb, tcp_len);
7447 queue_rx_frame(lro->parent,
7449 clear_lro_session(lro);
7450 swstats->flush_max_pkts++;
7452 case 2: /* Flush both */
7453 lro->parent->data_len = lro->frags_len;
7454 swstats->sending_both++;
7455 queue_rx_frame(lro->parent,
7457 clear_lro_session(lro);
7459 case 0: /* sessions exceeded */
7460 case -1: /* non-TCP or not L2 aggregatable */
7462 * First pkt in session not
7463 * L3/L4 aggregatable
7468 "%s: Samadhana!!\n",
7475 * Packet with erroneous checksum, let the
7476 * upper layers deal with it.
7478 skb_checksum_none_assert(skb);
7481 skb_checksum_none_assert(skb);
7483 swstats->mem_freed += skb->truesize;
7485 skb_record_rx_queue(skb, ring_no);
7486 queue_rx_frame(skb, RXD_GET_VLAN_TAG(rxdp->Control_2));
7488 sp->mac_control.rings[ring_no].rx_bufs_left -= 1;
7493 * s2io_link - stops/starts the Tx queue.
7494 * @sp : private member of the device structure, which is a pointer to the
7495 * s2io_nic structure.
7496 * @link : inidicates whether link is UP/DOWN.
7498 * This function stops/starts the Tx queue depending on whether the link
7499 * status of the NIC is is down or up. This is called by the Alarm
7500 * interrupt handler whenever a link change interrupt comes up.
7505 static void s2io_link(struct s2io_nic *sp, int link)
7507 struct net_device *dev = sp->dev;
7508 struct swStat *swstats = &sp->mac_control.stats_info->sw_stat;
7510 if (link != sp->last_link_state) {
7512 if (link == LINK_DOWN) {
7513 DBG_PRINT(ERR_DBG, "%s: Link down\n", dev->name);
7514 s2io_stop_all_tx_queue(sp);
7515 netif_carrier_off(dev);
7516 if (swstats->link_up_cnt)
7517 swstats->link_up_time =
7518 jiffies - sp->start_time;
7519 swstats->link_down_cnt++;
7521 DBG_PRINT(ERR_DBG, "%s: Link Up\n", dev->name);
7522 if (swstats->link_down_cnt)
7523 swstats->link_down_time =
7524 jiffies - sp->start_time;
7525 swstats->link_up_cnt++;
7526 netif_carrier_on(dev);
7527 s2io_wake_all_tx_queue(sp);
7530 sp->last_link_state = link;
7531 sp->start_time = jiffies;
7535 * s2io_init_pci -Initialization of PCI and PCI-X configuration registers .
7536 * @sp : private member of the device structure, which is a pointer to the
7537 * s2io_nic structure.
7539 * This function initializes a few of the PCI and PCI-X configuration registers
7540 * with recommended values.
7545 static void s2io_init_pci(struct s2io_nic *sp)
7547 u16 pci_cmd = 0, pcix_cmd = 0;
7549 /* Enable Data Parity Error Recovery in PCI-X command register. */
7550 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7552 pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7554 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7557 /* Set the PErr Response bit in PCI command register. */
7558 pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
7559 pci_write_config_word(sp->pdev, PCI_COMMAND,
7560 (pci_cmd | PCI_COMMAND_PARITY));
7561 pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
7564 static int s2io_verify_parm(struct pci_dev *pdev, u8 *dev_intr_type,
7569 if ((tx_fifo_num > MAX_TX_FIFOS) || (tx_fifo_num < 1)) {
7570 DBG_PRINT(ERR_DBG, "Requested number of tx fifos "
7571 "(%d) not supported\n", tx_fifo_num);
7573 if (tx_fifo_num < 1)
7576 tx_fifo_num = MAX_TX_FIFOS;
7578 DBG_PRINT(ERR_DBG, "Default to %d tx fifos\n", tx_fifo_num);
7582 *dev_multiq = multiq;
7584 if (tx_steering_type && (1 == tx_fifo_num)) {
7585 if (tx_steering_type != TX_DEFAULT_STEERING)
7587 "Tx steering is not supported with "
7588 "one fifo. Disabling Tx steering.\n");
7589 tx_steering_type = NO_STEERING;
7592 if ((tx_steering_type < NO_STEERING) ||
7593 (tx_steering_type > TX_DEFAULT_STEERING)) {
7595 "Requested transmit steering not supported\n");
7596 DBG_PRINT(ERR_DBG, "Disabling transmit steering\n");
7597 tx_steering_type = NO_STEERING;
7600 if (rx_ring_num > MAX_RX_RINGS) {
7602 "Requested number of rx rings not supported\n");
7603 DBG_PRINT(ERR_DBG, "Default to %d rx rings\n",
7605 rx_ring_num = MAX_RX_RINGS;
7608 if ((*dev_intr_type != INTA) && (*dev_intr_type != MSI_X)) {
7609 DBG_PRINT(ERR_DBG, "Wrong intr_type requested. "
7610 "Defaulting to INTA\n");
7611 *dev_intr_type = INTA;
7614 if ((*dev_intr_type == MSI_X) &&
7615 ((pdev->device != PCI_DEVICE_ID_HERC_WIN) &&
7616 (pdev->device != PCI_DEVICE_ID_HERC_UNI))) {
7617 DBG_PRINT(ERR_DBG, "Xframe I does not support MSI_X. "
7618 "Defaulting to INTA\n");
7619 *dev_intr_type = INTA;
7622 if ((rx_ring_mode != 1) && (rx_ring_mode != 2)) {
7623 DBG_PRINT(ERR_DBG, "Requested ring mode not supported\n");
7624 DBG_PRINT(ERR_DBG, "Defaulting to 1-buffer mode\n");
7628 for (i = 0; i < MAX_RX_RINGS; i++)
7629 if (rx_ring_sz[i] > MAX_RX_BLOCKS_PER_RING) {
7630 DBG_PRINT(ERR_DBG, "Requested rx ring size not "
7631 "supported\nDefaulting to %d\n",
7632 MAX_RX_BLOCKS_PER_RING);
7633 rx_ring_sz[i] = MAX_RX_BLOCKS_PER_RING;
7640 * rts_ds_steer - Receive traffic steering based on IPv4 or IPv6 TOS
7641 * or Traffic class respectively.
7642 * @nic: device private variable
7643 * Description: The function configures the receive steering to
7644 * desired receive ring.
7645 * Return Value: SUCCESS on success and
7646 * '-1' on failure (endian settings incorrect).
7648 static int rts_ds_steer(struct s2io_nic *nic, u8 ds_codepoint, u8 ring)
7650 struct XENA_dev_config __iomem *bar0 = nic->bar0;
7651 register u64 val64 = 0;
7653 if (ds_codepoint > 63)
7656 val64 = RTS_DS_MEM_DATA(ring);
7657 writeq(val64, &bar0->rts_ds_mem_data);
7659 val64 = RTS_DS_MEM_CTRL_WE |
7660 RTS_DS_MEM_CTRL_STROBE_NEW_CMD |
7661 RTS_DS_MEM_CTRL_OFFSET(ds_codepoint);
7663 writeq(val64, &bar0->rts_ds_mem_ctrl);
7665 return wait_for_cmd_complete(&bar0->rts_ds_mem_ctrl,
7666 RTS_DS_MEM_CTRL_STROBE_CMD_BEING_EXECUTED,
7670 static const struct net_device_ops s2io_netdev_ops = {
7671 .ndo_open = s2io_open,
7672 .ndo_stop = s2io_close,
7673 .ndo_get_stats = s2io_get_stats,
7674 .ndo_start_xmit = s2io_xmit,
7675 .ndo_validate_addr = eth_validate_addr,
7676 .ndo_set_rx_mode = s2io_set_multicast,
7677 .ndo_do_ioctl = s2io_ioctl,
7678 .ndo_set_mac_address = s2io_set_mac_addr,
7679 .ndo_change_mtu = s2io_change_mtu,
7680 .ndo_set_features = s2io_set_features,
7681 .ndo_tx_timeout = s2io_tx_watchdog,
7682 #ifdef CONFIG_NET_POLL_CONTROLLER
7683 .ndo_poll_controller = s2io_netpoll,
7688 * s2io_init_nic - Initialization of the adapter .
7689 * @pdev : structure containing the PCI related information of the device.
7690 * @pre: List of PCI devices supported by the driver listed in s2io_tbl.
7692 * The function initializes an adapter identified by the pci_dec structure.
7693 * All OS related initialization including memory and device structure and
7694 * initlaization of the device private variable is done. Also the swapper
7695 * control register is initialized to enable read and write into the I/O
7696 * registers of the device.
7698 * returns 0 on success and negative on failure.
7702 s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre)
7704 struct s2io_nic *sp;
7705 struct net_device *dev;
7707 int dma_flag = false;
7708 u32 mac_up, mac_down;
7709 u64 val64 = 0, tmp64 = 0;
7710 struct XENA_dev_config __iomem *bar0 = NULL;
7712 struct config_param *config;
7713 struct mac_info *mac_control;
7715 u8 dev_intr_type = intr_type;
7718 ret = s2io_verify_parm(pdev, &dev_intr_type, &dev_multiq);
7722 ret = pci_enable_device(pdev);
7725 "%s: pci_enable_device failed\n", __func__);
7729 if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
7730 DBG_PRINT(INIT_DBG, "%s: Using 64bit DMA\n", __func__);
7732 if (pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64))) {
7734 "Unable to obtain 64bit DMA "
7735 "for consistent allocations\n");
7736 pci_disable_device(pdev);
7739 } else if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
7740 DBG_PRINT(INIT_DBG, "%s: Using 32bit DMA\n", __func__);
7742 pci_disable_device(pdev);
7745 ret = pci_request_regions(pdev, s2io_driver_name);
7747 DBG_PRINT(ERR_DBG, "%s: Request Regions failed - %x\n",
7749 pci_disable_device(pdev);
7753 dev = alloc_etherdev_mq(sizeof(struct s2io_nic), tx_fifo_num);
7755 dev = alloc_etherdev(sizeof(struct s2io_nic));
7757 pci_disable_device(pdev);
7758 pci_release_regions(pdev);
7762 pci_set_master(pdev);
7763 pci_set_drvdata(pdev, dev);
7764 SET_NETDEV_DEV(dev, &pdev->dev);
7766 /* Private member variable initialized to s2io NIC structure */
7767 sp = netdev_priv(dev);
7770 sp->high_dma_flag = dma_flag;
7771 sp->device_enabled_once = false;
7772 if (rx_ring_mode == 1)
7773 sp->rxd_mode = RXD_MODE_1;
7774 if (rx_ring_mode == 2)
7775 sp->rxd_mode = RXD_MODE_3B;
7777 sp->config.intr_type = dev_intr_type;
7779 if ((pdev->device == PCI_DEVICE_ID_HERC_WIN) ||
7780 (pdev->device == PCI_DEVICE_ID_HERC_UNI))
7781 sp->device_type = XFRAME_II_DEVICE;
7783 sp->device_type = XFRAME_I_DEVICE;
7786 /* Initialize some PCI/PCI-X fields of the NIC. */
7790 * Setting the device configuration parameters.
7791 * Most of these parameters can be specified by the user during
7792 * module insertion as they are module loadable parameters. If
7793 * these parameters are not not specified during load time, they
7794 * are initialized with default values.
7796 config = &sp->config;
7797 mac_control = &sp->mac_control;
7799 config->napi = napi;
7800 config->tx_steering_type = tx_steering_type;
7802 /* Tx side parameters. */
7803 if (config->tx_steering_type == TX_PRIORITY_STEERING)
7804 config->tx_fifo_num = MAX_TX_FIFOS;
7806 config->tx_fifo_num = tx_fifo_num;
7808 /* Initialize the fifos used for tx steering */
7809 if (config->tx_fifo_num < 5) {
7810 if (config->tx_fifo_num == 1)
7811 sp->total_tcp_fifos = 1;
7813 sp->total_tcp_fifos = config->tx_fifo_num - 1;
7814 sp->udp_fifo_idx = config->tx_fifo_num - 1;
7815 sp->total_udp_fifos = 1;
7816 sp->other_fifo_idx = sp->total_tcp_fifos - 1;
7818 sp->total_tcp_fifos = (tx_fifo_num - FIFO_UDP_MAX_NUM -
7819 FIFO_OTHER_MAX_NUM);
7820 sp->udp_fifo_idx = sp->total_tcp_fifos;
7821 sp->total_udp_fifos = FIFO_UDP_MAX_NUM;
7822 sp->other_fifo_idx = sp->udp_fifo_idx + FIFO_UDP_MAX_NUM;
7825 config->multiq = dev_multiq;
7826 for (i = 0; i < config->tx_fifo_num; i++) {
7827 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
7829 tx_cfg->fifo_len = tx_fifo_len[i];
7830 tx_cfg->fifo_priority = i;
7833 /* mapping the QoS priority to the configured fifos */
7834 for (i = 0; i < MAX_TX_FIFOS; i++)
7835 config->fifo_mapping[i] = fifo_map[config->tx_fifo_num - 1][i];
7837 /* map the hashing selector table to the configured fifos */
7838 for (i = 0; i < config->tx_fifo_num; i++)
7839 sp->fifo_selector[i] = fifo_selector[i];
7842 config->tx_intr_type = TXD_INT_TYPE_UTILZ;
7843 for (i = 0; i < config->tx_fifo_num; i++) {
7844 struct tx_fifo_config *tx_cfg = &config->tx_cfg[i];
7846 tx_cfg->f_no_snoop = (NO_SNOOP_TXD | NO_SNOOP_TXD_BUFFER);
7847 if (tx_cfg->fifo_len < 65) {
7848 config->tx_intr_type = TXD_INT_TYPE_PER_LIST;
7852 /* + 2 because one Txd for skb->data and one Txd for UFO */
7853 config->max_txds = MAX_SKB_FRAGS + 2;
7855 /* Rx side parameters. */
7856 config->rx_ring_num = rx_ring_num;
7857 for (i = 0; i < config->rx_ring_num; i++) {
7858 struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
7859 struct ring_info *ring = &mac_control->rings[i];
7861 rx_cfg->num_rxd = rx_ring_sz[i] * (rxd_count[sp->rxd_mode] + 1);
7862 rx_cfg->ring_priority = i;
7863 ring->rx_bufs_left = 0;
7864 ring->rxd_mode = sp->rxd_mode;
7865 ring->rxd_count = rxd_count[sp->rxd_mode];
7866 ring->pdev = sp->pdev;
7867 ring->dev = sp->dev;
7870 for (i = 0; i < rx_ring_num; i++) {
7871 struct rx_ring_config *rx_cfg = &config->rx_cfg[i];
7873 rx_cfg->ring_org = RING_ORG_BUFF1;
7874 rx_cfg->f_no_snoop = (NO_SNOOP_RXD | NO_SNOOP_RXD_BUFFER);
7877 /* Setting Mac Control parameters */
7878 mac_control->rmac_pause_time = rmac_pause_time;
7879 mac_control->mc_pause_threshold_q0q3 = mc_pause_threshold_q0q3;
7880 mac_control->mc_pause_threshold_q4q7 = mc_pause_threshold_q4q7;
7883 /* initialize the shared memory used by the NIC and the host */
7884 if (init_shared_mem(sp)) {
7885 DBG_PRINT(ERR_DBG, "%s: Memory allocation failed\n", dev->name);
7887 goto mem_alloc_failed;
7890 sp->bar0 = pci_ioremap_bar(pdev, 0);
7892 DBG_PRINT(ERR_DBG, "%s: Neterion: cannot remap io mem1\n",
7895 goto bar0_remap_failed;
7898 sp->bar1 = pci_ioremap_bar(pdev, 2);
7900 DBG_PRINT(ERR_DBG, "%s: Neterion: cannot remap io mem2\n",
7903 goto bar1_remap_failed;
7906 /* Initializing the BAR1 address as the start of the FIFO pointer. */
7907 for (j = 0; j < MAX_TX_FIFOS; j++) {
7908 mac_control->tx_FIFO_start[j] = sp->bar1 + (j * 0x00020000);
7911 /* Driver entry points */
7912 dev->netdev_ops = &s2io_netdev_ops;
7913 dev->ethtool_ops = &netdev_ethtool_ops;
7914 dev->hw_features = NETIF_F_SG | NETIF_F_IP_CSUM |
7915 NETIF_F_TSO | NETIF_F_TSO6 |
7916 NETIF_F_RXCSUM | NETIF_F_LRO;
7917 dev->features |= dev->hw_features |
7918 NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX;
7919 if (sp->device_type & XFRAME_II_DEVICE) {
7920 dev->hw_features |= NETIF_F_UFO;
7922 dev->features |= NETIF_F_UFO;
7924 if (sp->high_dma_flag == true)
7925 dev->features |= NETIF_F_HIGHDMA;
7926 dev->watchdog_timeo = WATCH_DOG_TIMEOUT;
7927 INIT_WORK(&sp->rst_timer_task, s2io_restart_nic);
7928 INIT_WORK(&sp->set_link_task, s2io_set_link);
7930 pci_save_state(sp->pdev);
7932 /* Setting swapper control on the NIC, for proper reset operation */
7933 if (s2io_set_swapper(sp)) {
7934 DBG_PRINT(ERR_DBG, "%s: swapper settings are wrong\n",
7937 goto set_swap_failed;
7940 /* Verify if the Herc works on the slot its placed into */
7941 if (sp->device_type & XFRAME_II_DEVICE) {
7942 mode = s2io_verify_pci_mode(sp);
7944 DBG_PRINT(ERR_DBG, "%s: Unsupported PCI bus mode\n",
7947 goto set_swap_failed;
7951 if (sp->config.intr_type == MSI_X) {
7952 sp->num_entries = config->rx_ring_num + 1;
7953 ret = s2io_enable_msi_x(sp);
7956 ret = s2io_test_msi(sp);
7957 /* rollback MSI-X, will re-enable during add_isr() */
7958 remove_msix_isr(sp);
7963 "MSI-X requested but failed to enable\n");
7964 sp->config.intr_type = INTA;
7968 if (config->intr_type == MSI_X) {
7969 for (i = 0; i < config->rx_ring_num ; i++) {
7970 struct ring_info *ring = &mac_control->rings[i];
7972 netif_napi_add(dev, &ring->napi, s2io_poll_msix, 64);
7975 netif_napi_add(dev, &sp->napi, s2io_poll_inta, 64);
7978 /* Not needed for Herc */
7979 if (sp->device_type & XFRAME_I_DEVICE) {
7981 * Fix for all "FFs" MAC address problems observed on
7984 fix_mac_address(sp);
7989 * MAC address initialization.
7990 * For now only one mac address will be read and used.
7993 val64 = RMAC_ADDR_CMD_MEM_RD | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
7994 RMAC_ADDR_CMD_MEM_OFFSET(0 + S2IO_MAC_ADDR_START_OFFSET);
7995 writeq(val64, &bar0->rmac_addr_cmd_mem);
7996 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
7997 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
7999 tmp64 = readq(&bar0->rmac_addr_data0_mem);
8000 mac_down = (u32)tmp64;
8001 mac_up = (u32) (tmp64 >> 32);
8003 sp->def_mac_addr[0].mac_addr[3] = (u8) (mac_up);
8004 sp->def_mac_addr[0].mac_addr[2] = (u8) (mac_up >> 8);
8005 sp->def_mac_addr[0].mac_addr[1] = (u8) (mac_up >> 16);
8006 sp->def_mac_addr[0].mac_addr[0] = (u8) (mac_up >> 24);
8007 sp->def_mac_addr[0].mac_addr[5] = (u8) (mac_down >> 16);
8008 sp->def_mac_addr[0].mac_addr[4] = (u8) (mac_down >> 24);
8010 /* Set the factory defined MAC address initially */
8011 dev->addr_len = ETH_ALEN;
8012 memcpy(dev->dev_addr, sp->def_mac_addr, ETH_ALEN);
8014 /* initialize number of multicast & unicast MAC entries variables */
8015 if (sp->device_type == XFRAME_I_DEVICE) {
8016 config->max_mc_addr = S2IO_XENA_MAX_MC_ADDRESSES;
8017 config->max_mac_addr = S2IO_XENA_MAX_MAC_ADDRESSES;
8018 config->mc_start_offset = S2IO_XENA_MC_ADDR_START_OFFSET;
8019 } else if (sp->device_type == XFRAME_II_DEVICE) {
8020 config->max_mc_addr = S2IO_HERC_MAX_MC_ADDRESSES;
8021 config->max_mac_addr = S2IO_HERC_MAX_MAC_ADDRESSES;
8022 config->mc_start_offset = S2IO_HERC_MC_ADDR_START_OFFSET;
8025 /* store mac addresses from CAM to s2io_nic structure */
8026 do_s2io_store_unicast_mc(sp);
8028 /* Configure MSIX vector for number of rings configured plus one */
8029 if ((sp->device_type == XFRAME_II_DEVICE) &&
8030 (config->intr_type == MSI_X))
8031 sp->num_entries = config->rx_ring_num + 1;
8033 /* Store the values of the MSIX table in the s2io_nic structure */
8034 store_xmsi_data(sp);
8035 /* reset Nic and bring it to known state */
8039 * Initialize link state flags
8040 * and the card state parameter
8044 /* Initialize spinlocks */
8045 for (i = 0; i < sp->config.tx_fifo_num; i++) {
8046 struct fifo_info *fifo = &mac_control->fifos[i];
8048 spin_lock_init(&fifo->tx_lock);
8052 * SXE-002: Configure link and activity LED to init state
8055 subid = sp->pdev->subsystem_device;
8056 if ((subid & 0xFF) >= 0x07) {
8057 val64 = readq(&bar0->gpio_control);
8058 val64 |= 0x0000800000000000ULL;
8059 writeq(val64, &bar0->gpio_control);
8060 val64 = 0x0411040400000000ULL;
8061 writeq(val64, (void __iomem *)bar0 + 0x2700);
8062 val64 = readq(&bar0->gpio_control);
8065 sp->rx_csum = 1; /* Rx chksum verify enabled by default */
8067 if (register_netdev(dev)) {
8068 DBG_PRINT(ERR_DBG, "Device registration failed\n");
8070 goto register_failed;
8073 DBG_PRINT(ERR_DBG, "Copyright(c) 2002-2010 Exar Corp.\n");
8074 DBG_PRINT(ERR_DBG, "%s: Neterion %s (rev %d)\n", dev->name,
8075 sp->product_name, pdev->revision);
8076 DBG_PRINT(ERR_DBG, "%s: Driver version %s\n", dev->name,
8077 s2io_driver_version);
8078 DBG_PRINT(ERR_DBG, "%s: MAC Address: %pM\n", dev->name, dev->dev_addr);
8079 DBG_PRINT(ERR_DBG, "Serial number: %s\n", sp->serial_num);
8080 if (sp->device_type & XFRAME_II_DEVICE) {
8081 mode = s2io_print_pci_mode(sp);
8084 unregister_netdev(dev);
8085 goto set_swap_failed;
8088 switch (sp->rxd_mode) {
8090 DBG_PRINT(ERR_DBG, "%s: 1-Buffer receive mode enabled\n",
8094 DBG_PRINT(ERR_DBG, "%s: 2-Buffer receive mode enabled\n",
8099 switch (sp->config.napi) {
8101 DBG_PRINT(ERR_DBG, "%s: NAPI disabled\n", dev->name);
8104 DBG_PRINT(ERR_DBG, "%s: NAPI enabled\n", dev->name);
8108 DBG_PRINT(ERR_DBG, "%s: Using %d Tx fifo(s)\n", dev->name,
8109 sp->config.tx_fifo_num);
8111 DBG_PRINT(ERR_DBG, "%s: Using %d Rx ring(s)\n", dev->name,
8112 sp->config.rx_ring_num);
8114 switch (sp->config.intr_type) {
8116 DBG_PRINT(ERR_DBG, "%s: Interrupt type INTA\n", dev->name);
8119 DBG_PRINT(ERR_DBG, "%s: Interrupt type MSI-X\n", dev->name);
8122 if (sp->config.multiq) {
8123 for (i = 0; i < sp->config.tx_fifo_num; i++) {
8124 struct fifo_info *fifo = &mac_control->fifos[i];
8126 fifo->multiq = config->multiq;
8128 DBG_PRINT(ERR_DBG, "%s: Multiqueue support enabled\n",
8131 DBG_PRINT(ERR_DBG, "%s: Multiqueue support disabled\n",
8134 switch (sp->config.tx_steering_type) {
8136 DBG_PRINT(ERR_DBG, "%s: No steering enabled for transmit\n",
8139 case TX_PRIORITY_STEERING:
8141 "%s: Priority steering enabled for transmit\n",
8144 case TX_DEFAULT_STEERING:
8146 "%s: Default steering enabled for transmit\n",
8150 DBG_PRINT(ERR_DBG, "%s: Large receive offload enabled\n",
8154 "%s: UDP Fragmentation Offload(UFO) enabled\n",
8156 /* Initialize device name */
8157 sprintf(sp->name, "%s Neterion %s", dev->name, sp->product_name);
8160 sp->vlan_strip_flag = 1;
8162 sp->vlan_strip_flag = 0;
8165 * Make Link state as off at this point, when the Link change
8166 * interrupt comes the state will be automatically changed to
8169 netif_carrier_off(dev);
8180 free_shared_mem(sp);
8181 pci_disable_device(pdev);
8182 pci_release_regions(pdev);
8189 * s2io_rem_nic - Free the PCI device
8190 * @pdev: structure containing the PCI related information of the device.
8191 * Description: This function is called by the Pci subsystem to release a
8192 * PCI device and free up all resource held up by the device. This could
8193 * be in response to a Hot plug event or when the driver is to be removed
8197 static void s2io_rem_nic(struct pci_dev *pdev)
8199 struct net_device *dev = pci_get_drvdata(pdev);
8200 struct s2io_nic *sp;
8203 DBG_PRINT(ERR_DBG, "Driver Data is NULL!!\n");
8207 sp = netdev_priv(dev);
8209 cancel_work_sync(&sp->rst_timer_task);
8210 cancel_work_sync(&sp->set_link_task);
8212 unregister_netdev(dev);
8214 free_shared_mem(sp);
8217 pci_release_regions(pdev);
8219 pci_disable_device(pdev);
8223 * s2io_starter - Entry point for the driver
8224 * Description: This function is the entry point for the driver. It verifies
8225 * the module loadable parameters and initializes PCI configuration space.
8228 static int __init s2io_starter(void)
8230 return pci_register_driver(&s2io_driver);
8234 * s2io_closer - Cleanup routine for the driver
8235 * Description: This function is the cleanup routine for the driver. It
8236 * unregisters the driver.
8239 static __exit void s2io_closer(void)
8241 pci_unregister_driver(&s2io_driver);
8242 DBG_PRINT(INIT_DBG, "cleanup done\n");
8245 module_init(s2io_starter);
8246 module_exit(s2io_closer);
8248 static int check_L2_lro_capable(u8 *buffer, struct iphdr **ip,
8249 struct tcphdr **tcp, struct RxD_t *rxdp,
8250 struct s2io_nic *sp)
8253 u8 l2_type = (u8)((rxdp->Control_1 >> 37) & 0x7), ip_len;
8255 if (!(rxdp->Control_1 & RXD_FRAME_PROTO_TCP)) {
8257 "%s: Non-TCP frames not supported for LRO\n",
8262 /* Checking for DIX type or DIX type with VLAN */
8263 if ((l2_type == 0) || (l2_type == 4)) {
8264 ip_off = HEADER_ETHERNET_II_802_3_SIZE;
8266 * If vlan stripping is disabled and the frame is VLAN tagged,
8267 * shift the offset by the VLAN header size bytes.
8269 if ((!sp->vlan_strip_flag) &&
8270 (rxdp->Control_1 & RXD_FRAME_VLAN_TAG))
8271 ip_off += HEADER_VLAN_SIZE;
8273 /* LLC, SNAP etc are considered non-mergeable */
8277 *ip = (struct iphdr *)(buffer + ip_off);
8278 ip_len = (u8)((*ip)->ihl);
8280 *tcp = (struct tcphdr *)((unsigned long)*ip + ip_len);
8285 static int check_for_socket_match(struct lro *lro, struct iphdr *ip,
8288 DBG_PRINT(INFO_DBG, "%s: Been here...\n", __func__);
8289 if ((lro->iph->saddr != ip->saddr) ||
8290 (lro->iph->daddr != ip->daddr) ||
8291 (lro->tcph->source != tcp->source) ||
8292 (lro->tcph->dest != tcp->dest))
8297 static inline int get_l4_pyld_length(struct iphdr *ip, struct tcphdr *tcp)
8299 return ntohs(ip->tot_len) - (ip->ihl << 2) - (tcp->doff << 2);
8302 static void initiate_new_session(struct lro *lro, u8 *l2h,
8303 struct iphdr *ip, struct tcphdr *tcp,
8304 u32 tcp_pyld_len, u16 vlan_tag)
8306 DBG_PRINT(INFO_DBG, "%s: Been here...\n", __func__);
8310 lro->tcp_next_seq = tcp_pyld_len + ntohl(tcp->seq);
8311 lro->tcp_ack = tcp->ack_seq;
8313 lro->total_len = ntohs(ip->tot_len);
8315 lro->vlan_tag = vlan_tag;
8317 * Check if we saw TCP timestamp.
8318 * Other consistency checks have already been done.
8320 if (tcp->doff == 8) {
8322 ptr = (__be32 *)(tcp+1);
8324 lro->cur_tsval = ntohl(*(ptr+1));
8325 lro->cur_tsecr = *(ptr+2);
8330 static void update_L3L4_header(struct s2io_nic *sp, struct lro *lro)
8332 struct iphdr *ip = lro->iph;
8333 struct tcphdr *tcp = lro->tcph;
8334 struct swStat *swstats = &sp->mac_control.stats_info->sw_stat;
8336 DBG_PRINT(INFO_DBG, "%s: Been here...\n", __func__);
8338 /* Update L3 header */
8339 csum_replace2(&ip->check, ip->tot_len, htons(lro->total_len));
8340 ip->tot_len = htons(lro->total_len);
8342 /* Update L4 header */
8343 tcp->ack_seq = lro->tcp_ack;
8344 tcp->window = lro->window;
8346 /* Update tsecr field if this session has timestamps enabled */
8348 __be32 *ptr = (__be32 *)(tcp + 1);
8349 *(ptr+2) = lro->cur_tsecr;
8352 /* Update counters required for calculation of
8353 * average no. of packets aggregated.
8355 swstats->sum_avg_pkts_aggregated += lro->sg_num;
8356 swstats->num_aggregations++;
8359 static void aggregate_new_rx(struct lro *lro, struct iphdr *ip,
8360 struct tcphdr *tcp, u32 l4_pyld)
8362 DBG_PRINT(INFO_DBG, "%s: Been here...\n", __func__);
8363 lro->total_len += l4_pyld;
8364 lro->frags_len += l4_pyld;
8365 lro->tcp_next_seq += l4_pyld;
8368 /* Update ack seq no. and window ad(from this pkt) in LRO object */
8369 lro->tcp_ack = tcp->ack_seq;
8370 lro->window = tcp->window;
8374 /* Update tsecr and tsval from this packet */
8375 ptr = (__be32 *)(tcp+1);
8376 lro->cur_tsval = ntohl(*(ptr+1));
8377 lro->cur_tsecr = *(ptr + 2);
8381 static int verify_l3_l4_lro_capable(struct lro *l_lro, struct iphdr *ip,
8382 struct tcphdr *tcp, u32 tcp_pyld_len)
8386 DBG_PRINT(INFO_DBG, "%s: Been here...\n", __func__);
8388 if (!tcp_pyld_len) {
8389 /* Runt frame or a pure ack */
8393 if (ip->ihl != 5) /* IP has options */
8396 /* If we see CE codepoint in IP header, packet is not mergeable */
8397 if (INET_ECN_is_ce(ipv4_get_dsfield(ip)))
8400 /* If we see ECE or CWR flags in TCP header, packet is not mergeable */
8401 if (tcp->urg || tcp->psh || tcp->rst ||
8402 tcp->syn || tcp->fin ||
8403 tcp->ece || tcp->cwr || !tcp->ack) {
8405 * Currently recognize only the ack control word and
8406 * any other control field being set would result in
8407 * flushing the LRO session
8413 * Allow only one TCP timestamp option. Don't aggregate if
8414 * any other options are detected.
8416 if (tcp->doff != 5 && tcp->doff != 8)
8419 if (tcp->doff == 8) {
8420 ptr = (u8 *)(tcp + 1);
8421 while (*ptr == TCPOPT_NOP)
8423 if (*ptr != TCPOPT_TIMESTAMP || *(ptr+1) != TCPOLEN_TIMESTAMP)
8426 /* Ensure timestamp value increases monotonically */
8428 if (l_lro->cur_tsval > ntohl(*((__be32 *)(ptr+2))))
8431 /* timestamp echo reply should be non-zero */
8432 if (*((__be32 *)(ptr+6)) == 0)
8439 static int s2io_club_tcp_session(struct ring_info *ring_data, u8 *buffer,
8440 u8 **tcp, u32 *tcp_len, struct lro **lro,
8441 struct RxD_t *rxdp, struct s2io_nic *sp)
8444 struct tcphdr *tcph;
8447 struct swStat *swstats = &sp->mac_control.stats_info->sw_stat;
8449 ret = check_L2_lro_capable(buffer, &ip, (struct tcphdr **)tcp,
8454 DBG_PRINT(INFO_DBG, "IP Saddr: %x Daddr: %x\n", ip->saddr, ip->daddr);
8456 vlan_tag = RXD_GET_VLAN_TAG(rxdp->Control_2);
8457 tcph = (struct tcphdr *)*tcp;
8458 *tcp_len = get_l4_pyld_length(ip, tcph);
8459 for (i = 0; i < MAX_LRO_SESSIONS; i++) {
8460 struct lro *l_lro = &ring_data->lro0_n[i];
8461 if (l_lro->in_use) {
8462 if (check_for_socket_match(l_lro, ip, tcph))
8464 /* Sock pair matched */
8467 if ((*lro)->tcp_next_seq != ntohl(tcph->seq)) {
8468 DBG_PRINT(INFO_DBG, "%s: Out of sequence. "
8469 "expected 0x%x, actual 0x%x\n",
8471 (*lro)->tcp_next_seq,
8474 swstats->outof_sequence_pkts++;
8479 if (!verify_l3_l4_lro_capable(l_lro, ip, tcph,
8481 ret = 1; /* Aggregate */
8483 ret = 2; /* Flush both */
8489 /* Before searching for available LRO objects,
8490 * check if the pkt is L3/L4 aggregatable. If not
8491 * don't create new LRO session. Just send this
8494 if (verify_l3_l4_lro_capable(NULL, ip, tcph, *tcp_len))
8497 for (i = 0; i < MAX_LRO_SESSIONS; i++) {
8498 struct lro *l_lro = &ring_data->lro0_n[i];
8499 if (!(l_lro->in_use)) {
8501 ret = 3; /* Begin anew */
8507 if (ret == 0) { /* sessions exceeded */
8508 DBG_PRINT(INFO_DBG, "%s: All LRO sessions already in use\n",
8516 initiate_new_session(*lro, buffer, ip, tcph, *tcp_len,
8520 update_L3L4_header(sp, *lro);
8523 aggregate_new_rx(*lro, ip, tcph, *tcp_len);
8524 if ((*lro)->sg_num == sp->lro_max_aggr_per_sess) {
8525 update_L3L4_header(sp, *lro);
8526 ret = 4; /* Flush the LRO */
8530 DBG_PRINT(ERR_DBG, "%s: Don't know, can't say!!\n", __func__);
8537 static void clear_lro_session(struct lro *lro)
8539 static u16 lro_struct_size = sizeof(struct lro);
8541 memset(lro, 0, lro_struct_size);
8544 static void queue_rx_frame(struct sk_buff *skb, u16 vlan_tag)
8546 struct net_device *dev = skb->dev;
8547 struct s2io_nic *sp = netdev_priv(dev);
8549 skb->protocol = eth_type_trans(skb, dev);
8550 if (vlan_tag && sp->vlan_strip_flag)
8551 __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlan_tag);
8552 if (sp->config.napi)
8553 netif_receive_skb(skb);
8558 static void lro_append_pkt(struct s2io_nic *sp, struct lro *lro,
8559 struct sk_buff *skb, u32 tcp_len)
8561 struct sk_buff *first = lro->parent;
8562 struct swStat *swstats = &sp->mac_control.stats_info->sw_stat;
8564 first->len += tcp_len;
8565 first->data_len = lro->frags_len;
8566 skb_pull(skb, (skb->len - tcp_len));
8567 if (skb_shinfo(first)->frag_list)
8568 lro->last_frag->next = skb;
8570 skb_shinfo(first)->frag_list = skb;
8571 first->truesize += skb->truesize;
8572 lro->last_frag = skb;
8573 swstats->clubbed_frms_cnt++;
8577 * s2io_io_error_detected - called when PCI error is detected
8578 * @pdev: Pointer to PCI device
8579 * @state: The current pci connection state
8581 * This function is called after a PCI bus error affecting
8582 * this device has been detected.
8584 static pci_ers_result_t s2io_io_error_detected(struct pci_dev *pdev,
8585 pci_channel_state_t state)
8587 struct net_device *netdev = pci_get_drvdata(pdev);
8588 struct s2io_nic *sp = netdev_priv(netdev);
8590 netif_device_detach(netdev);
8592 if (state == pci_channel_io_perm_failure)
8593 return PCI_ERS_RESULT_DISCONNECT;
8595 if (netif_running(netdev)) {
8596 /* Bring down the card, while avoiding PCI I/O */
8597 do_s2io_card_down(sp, 0);
8599 pci_disable_device(pdev);
8601 return PCI_ERS_RESULT_NEED_RESET;
8605 * s2io_io_slot_reset - called after the pci bus has been reset.
8606 * @pdev: Pointer to PCI device
8608 * Restart the card from scratch, as if from a cold-boot.
8609 * At this point, the card has exprienced a hard reset,
8610 * followed by fixups by BIOS, and has its config space
8611 * set up identically to what it was at cold boot.
8613 static pci_ers_result_t s2io_io_slot_reset(struct pci_dev *pdev)
8615 struct net_device *netdev = pci_get_drvdata(pdev);
8616 struct s2io_nic *sp = netdev_priv(netdev);
8618 if (pci_enable_device(pdev)) {
8619 pr_err("Cannot re-enable PCI device after reset.\n");
8620 return PCI_ERS_RESULT_DISCONNECT;
8623 pci_set_master(pdev);
8626 return PCI_ERS_RESULT_RECOVERED;
8630 * s2io_io_resume - called when traffic can start flowing again.
8631 * @pdev: Pointer to PCI device
8633 * This callback is called when the error recovery driver tells
8634 * us that its OK to resume normal operation.
8636 static void s2io_io_resume(struct pci_dev *pdev)
8638 struct net_device *netdev = pci_get_drvdata(pdev);
8639 struct s2io_nic *sp = netdev_priv(netdev);
8641 if (netif_running(netdev)) {
8642 if (s2io_card_up(sp)) {
8643 pr_err("Can't bring device back up after reset.\n");
8647 if (s2io_set_mac_addr(netdev, netdev->dev_addr) == FAILURE) {
8649 pr_err("Can't restore mac addr after reset.\n");
8654 netif_device_attach(netdev);
8655 netif_tx_wake_all_queues(netdev);