1 /* Copyright 2008-2009 Broadcom Corporation
3 * Unless you and Broadcom execute a separate written software license
4 * agreement governing use of this software, this software is licensed to you
5 * under the terms of the GNU General Public License version 2, available
6 * at http://www.gnu.org/licenses/old-licenses/gpl-2.0.html (the "GPL").
8 * Notwithstanding the above, under no circumstances may you combine this
9 * software in any way with any other Broadcom software provided under a
10 * license other than the GPL, without Broadcom's express prior written
13 * Written by Yaniv Rosner
22 /***********************************************************/
24 /***********************************************************/
25 #define DEFAULT_PHY_DEV_ADDR 3
29 #define BNX2X_FLOW_CTRL_AUTO PORT_FEATURE_FLOW_CONTROL_AUTO
30 #define BNX2X_FLOW_CTRL_TX PORT_FEATURE_FLOW_CONTROL_TX
31 #define BNX2X_FLOW_CTRL_RX PORT_FEATURE_FLOW_CONTROL_RX
32 #define BNX2X_FLOW_CTRL_BOTH PORT_FEATURE_FLOW_CONTROL_BOTH
33 #define BNX2X_FLOW_CTRL_NONE PORT_FEATURE_FLOW_CONTROL_NONE
35 #define SPEED_AUTO_NEG 0
36 #define SPEED_12000 12000
37 #define SPEED_12500 12500
38 #define SPEED_13000 13000
39 #define SPEED_15000 15000
40 #define SPEED_16000 16000
42 #define SFP_EEPROM_VENDOR_NAME_ADDR 0x14
43 #define SFP_EEPROM_VENDOR_NAME_SIZE 16
44 #define SFP_EEPROM_VENDOR_OUI_ADDR 0x25
45 #define SFP_EEPROM_VENDOR_OUI_SIZE 3
46 #define SFP_EEPROM_PART_NO_ADDR 0x28
47 #define SFP_EEPROM_PART_NO_SIZE 16
48 #define PWR_FLT_ERR_MSG_LEN 250
49 /***********************************************************/
51 /***********************************************************/
52 /* Inputs parameters to the CLC */
57 /* Default / User Configuration */
59 #define LOOPBACK_NONE 0
60 #define LOOPBACK_EMAC 1
61 #define LOOPBACK_BMAC 2
62 #define LOOPBACK_XGXS_10 3
63 #define LOOPBACK_EXT_PHY 4
64 #define LOOPBACK_EXT 5
68 u16 req_fc_auto_adv; /* Should be set to TX / BOTH when
69 req_flow_ctrl is set to AUTO */
70 u16 req_line_speed; /* Also determine AutoNeg */
72 /* Device parameters */
75 /* shmem parameters */
79 #define SWITCH_CFG_1G PORT_FEATURE_CON_SWITCH_1G_SWITCH
80 #define SWITCH_CFG_10G PORT_FEATURE_CON_SWITCH_10G_SWITCH
81 #define SWITCH_CFG_AUTO_DETECT PORT_FEATURE_CON_SWITCH_AUTO_DETECT
83 u16 hw_led_mode; /* part of the hw_config read from the shmem */
85 /* phy_addr populated by the phy_init function */
91 #define XGXS_EXT_PHY_TYPE(ext_phy_config) (ext_phy_config & \
92 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK)
93 #define SERDES_EXT_PHY_TYPE(ext_phy_config) (ext_phy_config & \
94 PORT_HW_CFG_SERDES_EXT_PHY_TYPE_MASK)
95 /* Phy register parameter */
98 u16 xgxs_config_rx[4]; /* preemphasis values for the rx side */
99 u16 xgxs_config_tx[4]; /* preemphasis values for the tx side */
101 u32 feature_config_flags;
102 #define FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED (1<<0)
103 #define FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY (1<<2)
104 #define FEATURE_CONFIG_BCM8727_NOC (1<<3)
106 /* Device pointer passed to all callback functions */
110 /* Output parameters */
115 #define MAC_TYPE_NONE 0
116 #define MAC_TYPE_EMAC 1
117 #define MAC_TYPE_BMAC 2
119 u8 phy_link_up; /* internal phy link indication */
129 #define AUTO_NEG_DISABLED 0x0
130 #define AUTO_NEG_ENABLED 0x1
131 #define AUTO_NEG_COMPLETE 0x2
132 #define AUTO_NEG_PARALLEL_DETECTION_USED 0x3
134 /* The same definitions as the shmem parameter */
138 /***********************************************************/
140 /***********************************************************/
142 /* Initialize the phy */
143 u8 bnx2x_phy_init(struct link_params *input, struct link_vars *output);
145 /* Reset the link. Should be called when driver or interface goes down
146 Before calling phy firmware upgrade, the reset_ext_phy should be set
148 u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars,
151 /* bnx2x_link_update should be called upon link interrupt */
152 u8 bnx2x_link_update(struct link_params *input, struct link_vars *output);
154 /* use the following cl45 functions to read/write from external_phy
155 In order to use it to read/write internal phy registers, use
156 DEFAULT_PHY_DEV_ADDR as devad, and (_bank + (_addr & 0xf)) as
157 Use ext_phy_type of 0 in case of cl22 over cl45
159 u8 bnx2x_cl45_read(struct bnx2x *bp, u8 port, u32 ext_phy_type,
160 u8 phy_addr, u8 devad, u16 reg, u16 *ret_val);
162 u8 bnx2x_cl45_write(struct bnx2x *bp, u8 port, u32 ext_phy_type,
163 u8 phy_addr, u8 devad, u16 reg, u16 val);
165 /* Reads the link_status from the shmem,
166 and update the link vars accordingly */
167 void bnx2x_link_status_update(struct link_params *input,
168 struct link_vars *output);
169 /* returns string representing the fw_version of the external phy */
170 u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded,
171 u8 *version, u16 len);
174 Basically, the CLC takes care of the led for the link, but in case one needs
175 to set/unset the led unnaturally, set the "mode" to LED_MODE_OPER to
176 blink the led, and LED_MODE_OFF to set the led off.*/
177 u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed,
178 u16 hw_led_mode, u32 chip_id);
179 #define LED_MODE_OFF 0
180 #define LED_MODE_OPER 2
182 u8 bnx2x_override_led_value(struct bnx2x *bp, u8 port, u32 led_idx, u32 value);
184 /* bnx2x_handle_module_detect_int should be called upon module detection
186 void bnx2x_handle_module_detect_int(struct link_params *params);
188 /* Get the actual link status. In case it returns 0, link is up,
189 otherwise link is down*/
190 u8 bnx2x_test_link(struct link_params *input, struct link_vars *vars);
192 /* One-time initialization for external phy after power up */
193 u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base);
195 /* Reset the external PHY using GPIO */
196 void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port);
198 void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, u8 port, u8 phy_addr);
200 u8 bnx2x_read_sfp_module_eeprom(struct link_params *params, u16 addr,
201 u8 byte_cnt, u8 *o_buf);
203 #endif /* BNX2X_LINK_H */