2 * NXP LPC32XX NAND SLC driver
5 * Kevin Wells <kevin.wells@nxp.com>
6 * Roland Stigge <stigge@antcom.de>
8 * Copyright © 2011 NXP Semiconductors
9 * Copyright © 2012 Roland Stigge
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License, or
14 * (at your option) any later version.
16 * This program is distributed in the hope that it will be useful,
17 * but WITHOUT ANY WARRANTY; without even the implied warranty of
18 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
19 * GNU General Public License for more details.
22 #include <linux/slab.h>
23 #include <linux/module.h>
24 #include <linux/platform_device.h>
25 #include <linux/mtd/mtd.h>
26 #include <linux/mtd/nand.h>
27 #include <linux/mtd/partitions.h>
28 #include <linux/clk.h>
29 #include <linux/err.h>
30 #include <linux/delay.h>
33 #include <linux/dma-mapping.h>
34 #include <linux/dmaengine.h>
35 #include <linux/mtd/nand_ecc.h>
36 #include <linux/gpio.h>
38 #include <linux/of_mtd.h>
39 #include <linux/of_gpio.h>
40 #include <linux/mtd/lpc32xx_slc.h>
42 #define LPC32XX_MODNAME "lpc32xx-nand"
44 /**********************************************************************
45 * SLC NAND controller register offsets
46 **********************************************************************/
48 #define SLC_DATA(x) (x + 0x000)
49 #define SLC_ADDR(x) (x + 0x004)
50 #define SLC_CMD(x) (x + 0x008)
51 #define SLC_STOP(x) (x + 0x00C)
52 #define SLC_CTRL(x) (x + 0x010)
53 #define SLC_CFG(x) (x + 0x014)
54 #define SLC_STAT(x) (x + 0x018)
55 #define SLC_INT_STAT(x) (x + 0x01C)
56 #define SLC_IEN(x) (x + 0x020)
57 #define SLC_ISR(x) (x + 0x024)
58 #define SLC_ICR(x) (x + 0x028)
59 #define SLC_TAC(x) (x + 0x02C)
60 #define SLC_TC(x) (x + 0x030)
61 #define SLC_ECC(x) (x + 0x034)
62 #define SLC_DMA_DATA(x) (x + 0x038)
64 /**********************************************************************
65 * slc_ctrl register definitions
66 **********************************************************************/
67 #define SLCCTRL_SW_RESET (1 << 2) /* Reset the NAND controller bit */
68 #define SLCCTRL_ECC_CLEAR (1 << 1) /* Reset ECC bit */
69 #define SLCCTRL_DMA_START (1 << 0) /* Start DMA channel bit */
71 /**********************************************************************
72 * slc_cfg register definitions
73 **********************************************************************/
74 #define SLCCFG_CE_LOW (1 << 5) /* Force CE low bit */
75 #define SLCCFG_DMA_ECC (1 << 4) /* Enable DMA ECC bit */
76 #define SLCCFG_ECC_EN (1 << 3) /* ECC enable bit */
77 #define SLCCFG_DMA_BURST (1 << 2) /* DMA burst bit */
78 #define SLCCFG_DMA_DIR (1 << 1) /* DMA write(0)/read(1) bit */
79 #define SLCCFG_WIDTH (1 << 0) /* External device width, 0=8bit */
81 /**********************************************************************
82 * slc_stat register definitions
83 **********************************************************************/
84 #define SLCSTAT_DMA_FIFO (1 << 2) /* DMA FIFO has data bit */
85 #define SLCSTAT_SLC_FIFO (1 << 1) /* SLC FIFO has data bit */
86 #define SLCSTAT_NAND_READY (1 << 0) /* NAND device is ready bit */
88 /**********************************************************************
89 * slc_int_stat, slc_ien, slc_isr, and slc_icr register definitions
90 **********************************************************************/
91 #define SLCSTAT_INT_TC (1 << 1) /* Transfer count bit */
92 #define SLCSTAT_INT_RDY_EN (1 << 0) /* Ready interrupt bit */
94 /**********************************************************************
95 * slc_tac register definitions
96 **********************************************************************/
97 /* Computation of clock cycles on basis of controller and device clock rates */
98 #define SLCTAC_CLOCKS(c, n, s) (min_t(u32, DIV_ROUND_UP(c, n) - 1, 0xF) << s)
100 /* Clock setting for RDY write sample wait time in 2*n clocks */
101 #define SLCTAC_WDR(n) (((n) & 0xF) << 28)
102 /* Write pulse width in clock cycles, 1 to 16 clocks */
103 #define SLCTAC_WWIDTH(c, n) (SLCTAC_CLOCKS(c, n, 24))
104 /* Write hold time of control and data signals, 1 to 16 clocks */
105 #define SLCTAC_WHOLD(c, n) (SLCTAC_CLOCKS(c, n, 20))
106 /* Write setup time of control and data signals, 1 to 16 clocks */
107 #define SLCTAC_WSETUP(c, n) (SLCTAC_CLOCKS(c, n, 16))
108 /* Clock setting for RDY read sample wait time in 2*n clocks */
109 #define SLCTAC_RDR(n) (((n) & 0xF) << 12)
110 /* Read pulse width in clock cycles, 1 to 16 clocks */
111 #define SLCTAC_RWIDTH(c, n) (SLCTAC_CLOCKS(c, n, 8))
112 /* Read hold time of control and data signals, 1 to 16 clocks */
113 #define SLCTAC_RHOLD(c, n) (SLCTAC_CLOCKS(c, n, 4))
114 /* Read setup time of control and data signals, 1 to 16 clocks */
115 #define SLCTAC_RSETUP(c, n) (SLCTAC_CLOCKS(c, n, 0))
117 /**********************************************************************
118 * slc_ecc register definitions
119 **********************************************************************/
120 /* ECC line party fetch macro */
121 #define SLCECC_TO_LINEPAR(n) (((n) >> 6) & 0x7FFF)
122 #define SLCECC_TO_COLPAR(n) ((n) & 0x3F)
125 * DMA requires storage space for the DMA local buffer and the hardware ECC
126 * storage area. The DMA local buffer is only used if DMA mapping fails
129 #define LPC32XX_DMA_DATA_SIZE 4096
130 #define LPC32XX_ECC_SAVE_SIZE ((4096 / 256) * 4)
132 /* Number of bytes used for ECC stored in NAND per 256 bytes */
133 #define LPC32XX_SLC_DEV_ECC_BYTES 3
136 * If the NAND base clock frequency can't be fetched, this frequency will be
137 * used instead as the base. This rate is used to setup the timing registers
138 * used for NAND accesses.
140 #define LPC32XX_DEF_BUS_RATE 133250000
142 /* Milliseconds for DMA FIFO timeout (unlikely anyway) */
143 #define LPC32XX_DMA_TIMEOUT 100
146 * NAND ECC Layout for small page NAND devices
147 * Note: For large and huge page devices, the default layouts are used
149 static struct nand_ecclayout lpc32xx_nand_oob_16 = {
151 .eccpos = {10, 11, 12, 13, 14, 15},
153 { .offset = 0, .length = 4 },
154 { .offset = 6, .length = 4 },
158 static u8 bbt_pattern[] = {'B', 'b', 't', '0' };
159 static u8 mirror_pattern[] = {'1', 't', 'b', 'B' };
162 * Small page FLASH BBT descriptors, marker at offset 0, version at offset 6
163 * Note: Large page devices used the default layout
165 static struct nand_bbt_descr bbt_smallpage_main_descr = {
166 .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
167 | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
172 .pattern = bbt_pattern
175 static struct nand_bbt_descr bbt_smallpage_mirror_descr = {
176 .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
177 | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
182 .pattern = mirror_pattern
186 * NAND platform configuration structure
188 struct lpc32xx_nand_cfg_slc {
199 struct mtd_partition *parts;
203 struct lpc32xx_nand_host {
204 struct nand_chip nand_chip;
205 struct lpc32xx_slc_platform_data *pdata;
208 void __iomem *io_base;
209 struct lpc32xx_nand_cfg_slc *ncfg;
211 struct completion comp;
212 struct dma_chan *dma_chan;
213 uint32_t dma_buf_len;
214 struct dma_slave_config dma_slave_config;
215 struct scatterlist sgl;
218 * DMA and CPU addresses of ECC work area and data buffer
222 dma_addr_t io_base_dma;
225 static void lpc32xx_nand_setup(struct lpc32xx_nand_host *host)
227 uint32_t clkrate, tmp;
229 /* Reset SLC controller */
230 writel(SLCCTRL_SW_RESET, SLC_CTRL(host->io_base));
234 writel(0, SLC_CFG(host->io_base));
235 writel(0, SLC_IEN(host->io_base));
236 writel((SLCSTAT_INT_TC | SLCSTAT_INT_RDY_EN),
237 SLC_ICR(host->io_base));
239 /* Get base clock for SLC block */
240 clkrate = clk_get_rate(host->clk);
242 clkrate = LPC32XX_DEF_BUS_RATE;
244 /* Compute clock setup values */
245 tmp = SLCTAC_WDR(host->ncfg->wdr_clks) |
246 SLCTAC_WWIDTH(clkrate, host->ncfg->wwidth) |
247 SLCTAC_WHOLD(clkrate, host->ncfg->whold) |
248 SLCTAC_WSETUP(clkrate, host->ncfg->wsetup) |
249 SLCTAC_RDR(host->ncfg->rdr_clks) |
250 SLCTAC_RWIDTH(clkrate, host->ncfg->rwidth) |
251 SLCTAC_RHOLD(clkrate, host->ncfg->rhold) |
252 SLCTAC_RSETUP(clkrate, host->ncfg->rsetup);
253 writel(tmp, SLC_TAC(host->io_base));
257 * Hardware specific access to control lines
259 static void lpc32xx_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
263 struct nand_chip *chip = mtd->priv;
264 struct lpc32xx_nand_host *host = chip->priv;
266 /* Does CE state need to be changed? */
267 tmp = readl(SLC_CFG(host->io_base));
269 tmp |= SLCCFG_CE_LOW;
271 tmp &= ~SLCCFG_CE_LOW;
272 writel(tmp, SLC_CFG(host->io_base));
274 if (cmd != NAND_CMD_NONE) {
276 writel(cmd, SLC_CMD(host->io_base));
278 writel(cmd, SLC_ADDR(host->io_base));
283 * Read the Device Ready pin
285 static int lpc32xx_nand_device_ready(struct mtd_info *mtd)
287 struct nand_chip *chip = mtd->priv;
288 struct lpc32xx_nand_host *host = chip->priv;
291 if ((readl(SLC_STAT(host->io_base)) & SLCSTAT_NAND_READY) != 0)
298 * Enable NAND write protect
300 static void lpc32xx_wp_enable(struct lpc32xx_nand_host *host)
302 if (gpio_is_valid(host->ncfg->wp_gpio))
303 gpio_set_value(host->ncfg->wp_gpio, 0);
307 * Disable NAND write protect
309 static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
311 if (gpio_is_valid(host->ncfg->wp_gpio))
312 gpio_set_value(host->ncfg->wp_gpio, 1);
316 * Prepares SLC for transfers with H/W ECC enabled
318 static void lpc32xx_nand_ecc_enable(struct mtd_info *mtd, int mode)
320 /* Hardware ECC is enabled automatically in hardware as needed */
324 * Calculates the ECC for the data
326 static int lpc32xx_nand_ecc_calculate(struct mtd_info *mtd,
327 const unsigned char *buf,
331 * ECC is calculated automatically in hardware during syndrome read
332 * and write operations, so it doesn't need to be calculated here.
338 * Read a single byte from NAND device
340 static uint8_t lpc32xx_nand_read_byte(struct mtd_info *mtd)
342 struct nand_chip *chip = mtd->priv;
343 struct lpc32xx_nand_host *host = chip->priv;
345 return (uint8_t)readl(SLC_DATA(host->io_base));
349 * Simple device read without ECC
351 static void lpc32xx_nand_read_buf(struct mtd_info *mtd, u_char *buf, int len)
353 struct nand_chip *chip = mtd->priv;
354 struct lpc32xx_nand_host *host = chip->priv;
356 /* Direct device read with no ECC */
358 *buf++ = (uint8_t)readl(SLC_DATA(host->io_base));
362 * Simple device write without ECC
364 static void lpc32xx_nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
366 struct nand_chip *chip = mtd->priv;
367 struct lpc32xx_nand_host *host = chip->priv;
369 /* Direct device write with no ECC */
371 writel((uint32_t)*buf++, SLC_DATA(host->io_base));
375 * Read the OOB data from the device without ECC using FIFO method
377 static int lpc32xx_nand_read_oob_syndrome(struct mtd_info *mtd,
378 struct nand_chip *chip, int page)
380 chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
381 chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
387 * Write the OOB data to the device without ECC using FIFO method
389 static int lpc32xx_nand_write_oob_syndrome(struct mtd_info *mtd,
390 struct nand_chip *chip, int page)
394 chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page);
395 chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
397 /* Send command to program the OOB data */
398 chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
400 status = chip->waitfunc(mtd, chip);
402 return status & NAND_STATUS_FAIL ? -EIO : 0;
406 * Fills in the ECC fields in the OOB buffer with the hardware generated ECC
408 static void lpc32xx_slc_ecc_copy(uint8_t *spare, const uint32_t *ecc, int count)
412 for (i = 0; i < (count * 3); i += 3) {
413 uint32_t ce = ecc[i / 3];
414 ce = ~(ce << 2) & 0xFFFFFF;
415 spare[i + 2] = (uint8_t)(ce & 0xFF);
417 spare[i + 1] = (uint8_t)(ce & 0xFF);
419 spare[i] = (uint8_t)(ce & 0xFF);
423 static void lpc32xx_dma_complete_func(void *completion)
425 complete(completion);
428 static int lpc32xx_xmit_dma(struct mtd_info *mtd, dma_addr_t dma,
429 void *mem, int len, enum dma_transfer_direction dir)
431 struct nand_chip *chip = mtd->priv;
432 struct lpc32xx_nand_host *host = chip->priv;
433 struct dma_async_tx_descriptor *desc;
434 int flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
437 host->dma_slave_config.direction = dir;
438 host->dma_slave_config.src_addr = dma;
439 host->dma_slave_config.dst_addr = dma;
440 host->dma_slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
441 host->dma_slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
442 host->dma_slave_config.src_maxburst = 4;
443 host->dma_slave_config.dst_maxburst = 4;
444 /* DMA controller does flow control: */
445 host->dma_slave_config.device_fc = false;
446 if (dmaengine_slave_config(host->dma_chan, &host->dma_slave_config)) {
447 dev_err(mtd->dev.parent, "Failed to setup DMA slave\n");
451 sg_init_one(&host->sgl, mem, len);
453 res = dma_map_sg(host->dma_chan->device->dev, &host->sgl, 1,
456 dev_err(mtd->dev.parent, "Failed to map sg list\n");
459 desc = dmaengine_prep_slave_sg(host->dma_chan, &host->sgl, 1, dir,
462 dev_err(mtd->dev.parent, "Failed to prepare slave sg\n");
466 init_completion(&host->comp);
467 desc->callback = lpc32xx_dma_complete_func;
468 desc->callback_param = &host->comp;
470 dmaengine_submit(desc);
471 dma_async_issue_pending(host->dma_chan);
473 wait_for_completion_timeout(&host->comp, msecs_to_jiffies(1000));
475 dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1,
480 dma_unmap_sg(host->dma_chan->device->dev, &host->sgl, 1,
486 * DMA read/write transfers with ECC support
488 static int lpc32xx_xfer(struct mtd_info *mtd, uint8_t *buf, int eccsubpages,
491 struct nand_chip *chip = mtd->priv;
492 struct lpc32xx_nand_host *host = chip->priv;
494 unsigned long timeout;
496 enum dma_transfer_direction dir =
497 read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV;
501 if ((void *)buf <= high_memory) {
505 dma_buf = host->data_buf;
508 memcpy(host->data_buf, buf, mtd->writesize);
512 writel(readl(SLC_CFG(host->io_base)) |
513 SLCCFG_DMA_DIR | SLCCFG_ECC_EN | SLCCFG_DMA_ECC |
514 SLCCFG_DMA_BURST, SLC_CFG(host->io_base));
516 writel((readl(SLC_CFG(host->io_base)) |
517 SLCCFG_ECC_EN | SLCCFG_DMA_ECC | SLCCFG_DMA_BURST) &
519 SLC_CFG(host->io_base));
522 /* Clear initial ECC */
523 writel(SLCCTRL_ECC_CLEAR, SLC_CTRL(host->io_base));
525 /* Transfer size is data area only */
526 writel(mtd->writesize, SLC_TC(host->io_base));
528 /* Start transfer in the NAND controller */
529 writel(readl(SLC_CTRL(host->io_base)) | SLCCTRL_DMA_START,
530 SLC_CTRL(host->io_base));
532 for (i = 0; i < chip->ecc.steps; i++) {
534 res = lpc32xx_xmit_dma(mtd, SLC_DMA_DATA(host->io_base_dma),
535 dma_buf + i * chip->ecc.size,
536 mtd->writesize / chip->ecc.steps, dir);
540 /* Always _read_ ECC */
541 if (i == chip->ecc.steps - 1)
543 if (!read) /* ECC availability delayed on write */
545 res = lpc32xx_xmit_dma(mtd, SLC_ECC(host->io_base_dma),
546 &host->ecc_buf[i], 4, DMA_DEV_TO_MEM);
552 * According to NXP, the DMA can be finished here, but the NAND
553 * controller may still have buffered data. After porting to using the
554 * dmaengine DMA driver (amba-pl080), the condition (DMA_FIFO empty)
555 * appears to be always true, according to tests. Keeping the check for
556 * safety reasons for now.
558 if (readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO) {
559 dev_warn(mtd->dev.parent, "FIFO not empty!\n");
560 timeout = jiffies + msecs_to_jiffies(LPC32XX_DMA_TIMEOUT);
561 while ((readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO) &&
562 time_before(jiffies, timeout))
564 if (!time_before(jiffies, timeout)) {
565 dev_err(mtd->dev.parent, "FIFO held data too long\n");
570 /* Read last calculated ECC value */
573 host->ecc_buf[chip->ecc.steps - 1] =
574 readl(SLC_ECC(host->io_base));
577 dmaengine_terminate_all(host->dma_chan);
579 if (readl(SLC_STAT(host->io_base)) & SLCSTAT_DMA_FIFO ||
580 readl(SLC_TC(host->io_base))) {
581 /* Something is left in the FIFO, something is wrong */
582 dev_err(mtd->dev.parent, "DMA FIFO failure\n");
586 /* Stop DMA & HW ECC */
587 writel(readl(SLC_CTRL(host->io_base)) & ~SLCCTRL_DMA_START,
588 SLC_CTRL(host->io_base));
589 writel(readl(SLC_CFG(host->io_base)) &
590 ~(SLCCFG_DMA_DIR | SLCCFG_ECC_EN | SLCCFG_DMA_ECC |
591 SLCCFG_DMA_BURST), SLC_CFG(host->io_base));
593 if (!dma_mapped && read)
594 memcpy(buf, host->data_buf, mtd->writesize);
600 * Read the data and OOB data from the device, use ECC correction with the
601 * data, disable ECC for the OOB data
603 static int lpc32xx_nand_read_page_syndrome(struct mtd_info *mtd,
604 struct nand_chip *chip, uint8_t *buf,
605 int oob_required, int page)
607 struct lpc32xx_nand_host *host = chip->priv;
609 uint8_t *oobecc, tmpecc[LPC32XX_ECC_SAVE_SIZE];
611 /* Issue read command */
612 chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
614 /* Read data and oob, calculate ECC */
615 status = lpc32xx_xfer(mtd, buf, chip->ecc.steps, 1);
618 chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
620 /* Convert to stored ECC format */
621 lpc32xx_slc_ecc_copy(tmpecc, (uint32_t *) host->ecc_buf, chip->ecc.steps);
623 /* Pointer to ECC data retrieved from NAND spare area */
624 oobecc = chip->oob_poi + chip->ecc.layout->eccpos[0];
626 for (i = 0; i < chip->ecc.steps; i++) {
627 stat = chip->ecc.correct(mtd, buf, oobecc,
628 &tmpecc[i * chip->ecc.bytes]);
630 mtd->ecc_stats.failed++;
632 mtd->ecc_stats.corrected += stat;
634 buf += chip->ecc.size;
635 oobecc += chip->ecc.bytes;
642 * Read the data and OOB data from the device, no ECC correction with the
645 static int lpc32xx_nand_read_page_raw_syndrome(struct mtd_info *mtd,
646 struct nand_chip *chip,
647 uint8_t *buf, int oob_required,
650 /* Issue read command */
651 chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
653 /* Raw reads can just use the FIFO interface */
654 chip->read_buf(mtd, buf, chip->ecc.size * chip->ecc.steps);
655 chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
661 * Write the data and OOB data to the device, use ECC with the data,
662 * disable ECC for the OOB data
664 static int lpc32xx_nand_write_page_syndrome(struct mtd_info *mtd,
665 struct nand_chip *chip,
667 int oob_required, int page)
669 struct lpc32xx_nand_host *host = chip->priv;
670 uint8_t *pb = chip->oob_poi + chip->ecc.layout->eccpos[0];
673 /* Write data, calculate ECC on outbound data */
674 error = lpc32xx_xfer(mtd, (uint8_t *)buf, chip->ecc.steps, 0);
679 * The calculated ECC needs some manual work done to it before
680 * committing it to NAND. Process the calculated ECC and place
681 * the resultant values directly into the OOB buffer. */
682 lpc32xx_slc_ecc_copy(pb, (uint32_t *)host->ecc_buf, chip->ecc.steps);
684 /* Write ECC data to device */
685 chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
690 * Write the data and OOB data to the device, no ECC correction with the
693 static int lpc32xx_nand_write_page_raw_syndrome(struct mtd_info *mtd,
694 struct nand_chip *chip,
696 int oob_required, int page)
698 /* Raw writes can just use the FIFO interface */
699 chip->write_buf(mtd, buf, chip->ecc.size * chip->ecc.steps);
700 chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
704 static int lpc32xx_nand_dma_setup(struct lpc32xx_nand_host *host)
706 struct mtd_info *mtd = &host->mtd;
709 if (!host->pdata || !host->pdata->dma_filter) {
710 dev_err(mtd->dev.parent, "no DMA platform data\n");
715 dma_cap_set(DMA_SLAVE, mask);
716 host->dma_chan = dma_request_channel(mask, host->pdata->dma_filter,
718 if (!host->dma_chan) {
719 dev_err(mtd->dev.parent, "Failed to request DMA channel\n");
726 static struct lpc32xx_nand_cfg_slc *lpc32xx_parse_dt(struct device *dev)
728 struct lpc32xx_nand_cfg_slc *ncfg;
729 struct device_node *np = dev->of_node;
731 ncfg = devm_kzalloc(dev, sizeof(*ncfg), GFP_KERNEL);
735 of_property_read_u32(np, "nxp,wdr-clks", &ncfg->wdr_clks);
736 of_property_read_u32(np, "nxp,wwidth", &ncfg->wwidth);
737 of_property_read_u32(np, "nxp,whold", &ncfg->whold);
738 of_property_read_u32(np, "nxp,wsetup", &ncfg->wsetup);
739 of_property_read_u32(np, "nxp,rdr-clks", &ncfg->rdr_clks);
740 of_property_read_u32(np, "nxp,rwidth", &ncfg->rwidth);
741 of_property_read_u32(np, "nxp,rhold", &ncfg->rhold);
742 of_property_read_u32(np, "nxp,rsetup", &ncfg->rsetup);
744 if (!ncfg->wdr_clks || !ncfg->wwidth || !ncfg->whold ||
745 !ncfg->wsetup || !ncfg->rdr_clks || !ncfg->rwidth ||
746 !ncfg->rhold || !ncfg->rsetup) {
747 dev_err(dev, "chip parameters not specified correctly\n");
751 ncfg->use_bbt = of_get_nand_on_flash_bbt(np);
752 ncfg->wp_gpio = of_get_named_gpio(np, "gpios", 0);
758 * Probe for NAND controller
760 static int lpc32xx_nand_probe(struct platform_device *pdev)
762 struct lpc32xx_nand_host *host;
763 struct mtd_info *mtd;
764 struct nand_chip *chip;
766 struct mtd_part_parser_data ppdata = {};
769 rc = platform_get_resource(pdev, IORESOURCE_MEM, 0);
771 dev_err(&pdev->dev, "No memory resource found for device\n");
775 /* Allocate memory for the device structure (and zero it) */
776 host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL);
779 host->io_base_dma = rc->start;
781 host->io_base = devm_ioremap_resource(&pdev->dev, rc);
782 if (IS_ERR(host->io_base))
783 return PTR_ERR(host->io_base);
785 if (pdev->dev.of_node)
786 host->ncfg = lpc32xx_parse_dt(&pdev->dev);
789 "Missing or bad NAND config from device tree\n");
792 if (host->ncfg->wp_gpio == -EPROBE_DEFER)
793 return -EPROBE_DEFER;
794 if (gpio_is_valid(host->ncfg->wp_gpio) && devm_gpio_request(&pdev->dev,
795 host->ncfg->wp_gpio, "NAND WP")) {
796 dev_err(&pdev->dev, "GPIO not available\n");
799 lpc32xx_wp_disable(host);
801 host->pdata = dev_get_platdata(&pdev->dev);
804 chip = &host->nand_chip;
807 mtd->owner = THIS_MODULE;
808 mtd->dev.parent = &pdev->dev;
811 host->clk = devm_clk_get(&pdev->dev, NULL);
812 if (IS_ERR(host->clk)) {
813 dev_err(&pdev->dev, "Clock failure\n");
817 clk_prepare_enable(host->clk);
819 /* Set NAND IO addresses and command/ready functions */
820 chip->IO_ADDR_R = SLC_DATA(host->io_base);
821 chip->IO_ADDR_W = SLC_DATA(host->io_base);
822 chip->cmd_ctrl = lpc32xx_nand_cmd_ctrl;
823 chip->dev_ready = lpc32xx_nand_device_ready;
824 chip->chip_delay = 20; /* 20us command delay time */
826 /* Init NAND controller */
827 lpc32xx_nand_setup(host);
829 platform_set_drvdata(pdev, host);
831 /* NAND callbacks for LPC32xx SLC hardware */
832 chip->ecc.mode = NAND_ECC_HW_SYNDROME;
833 chip->read_byte = lpc32xx_nand_read_byte;
834 chip->read_buf = lpc32xx_nand_read_buf;
835 chip->write_buf = lpc32xx_nand_write_buf;
836 chip->ecc.read_page_raw = lpc32xx_nand_read_page_raw_syndrome;
837 chip->ecc.read_page = lpc32xx_nand_read_page_syndrome;
838 chip->ecc.write_page_raw = lpc32xx_nand_write_page_raw_syndrome;
839 chip->ecc.write_page = lpc32xx_nand_write_page_syndrome;
840 chip->ecc.write_oob = lpc32xx_nand_write_oob_syndrome;
841 chip->ecc.read_oob = lpc32xx_nand_read_oob_syndrome;
842 chip->ecc.calculate = lpc32xx_nand_ecc_calculate;
843 chip->ecc.correct = nand_correct_data;
844 chip->ecc.strength = 1;
845 chip->ecc.hwctl = lpc32xx_nand_ecc_enable;
848 * Allocate a large enough buffer for a single huge page plus
849 * extra space for the spare area and ECC storage area
851 host->dma_buf_len = LPC32XX_DMA_DATA_SIZE + LPC32XX_ECC_SAVE_SIZE;
852 host->data_buf = devm_kzalloc(&pdev->dev, host->dma_buf_len,
854 if (host->data_buf == NULL) {
859 res = lpc32xx_nand_dma_setup(host);
865 /* Find NAND device */
866 if (nand_scan_ident(mtd, 1, NULL)) {
871 /* OOB and ECC CPU and DMA work areas */
872 host->ecc_buf = (uint32_t *)(host->data_buf + LPC32XX_DMA_DATA_SIZE);
875 * Small page FLASH has a unique OOB layout, but large and huge
876 * page FLASH use the standard layout. Small page FLASH uses a
877 * custom BBT marker layout.
879 if (mtd->writesize <= 512)
880 chip->ecc.layout = &lpc32xx_nand_oob_16;
882 /* These sizes remain the same regardless of page size */
883 chip->ecc.size = 256;
884 chip->ecc.bytes = LPC32XX_SLC_DEV_ECC_BYTES;
885 chip->ecc.prepad = chip->ecc.postpad = 0;
887 /* Avoid extra scan if using BBT, setup BBT support */
888 if (host->ncfg->use_bbt) {
889 chip->bbt_options |= NAND_BBT_USE_FLASH;
892 * Use a custom BBT marker setup for small page FLASH that
893 * won't interfere with the ECC layout. Large and huge page
894 * FLASH use the standard layout.
896 if (mtd->writesize <= 512) {
897 chip->bbt_td = &bbt_smallpage_main_descr;
898 chip->bbt_md = &bbt_smallpage_mirror_descr;
903 * Fills out all the uninitialized function pointers with the defaults
905 if (nand_scan_tail(mtd)) {
910 mtd->name = "nxp_lpc3220_slc";
911 ppdata.of_node = pdev->dev.of_node;
912 res = mtd_device_parse_register(mtd, NULL, &ppdata, host->ncfg->parts,
913 host->ncfg->num_parts);
920 dma_release_channel(host->dma_chan);
922 clk_disable_unprepare(host->clk);
924 lpc32xx_wp_enable(host);
930 * Remove NAND device.
932 static int lpc32xx_nand_remove(struct platform_device *pdev)
935 struct lpc32xx_nand_host *host = platform_get_drvdata(pdev);
936 struct mtd_info *mtd = &host->mtd;
939 dma_release_channel(host->dma_chan);
942 tmp = readl(SLC_CTRL(host->io_base));
943 tmp &= ~SLCCFG_CE_LOW;
944 writel(tmp, SLC_CTRL(host->io_base));
946 clk_disable_unprepare(host->clk);
947 lpc32xx_wp_enable(host);
953 static int lpc32xx_nand_resume(struct platform_device *pdev)
955 struct lpc32xx_nand_host *host = platform_get_drvdata(pdev);
957 /* Re-enable NAND clock */
958 clk_prepare_enable(host->clk);
960 /* Fresh init of NAND controller */
961 lpc32xx_nand_setup(host);
963 /* Disable write protect */
964 lpc32xx_wp_disable(host);
969 static int lpc32xx_nand_suspend(struct platform_device *pdev, pm_message_t pm)
972 struct lpc32xx_nand_host *host = platform_get_drvdata(pdev);
975 tmp = readl(SLC_CTRL(host->io_base));
976 tmp &= ~SLCCFG_CE_LOW;
977 writel(tmp, SLC_CTRL(host->io_base));
979 /* Enable write protect for safety */
980 lpc32xx_wp_enable(host);
983 clk_disable_unprepare(host->clk);
989 #define lpc32xx_nand_resume NULL
990 #define lpc32xx_nand_suspend NULL
993 static const struct of_device_id lpc32xx_nand_match[] = {
994 { .compatible = "nxp,lpc3220-slc" },
997 MODULE_DEVICE_TABLE(of, lpc32xx_nand_match);
999 static struct platform_driver lpc32xx_nand_driver = {
1000 .probe = lpc32xx_nand_probe,
1001 .remove = lpc32xx_nand_remove,
1002 .resume = lpc32xx_nand_resume,
1003 .suspend = lpc32xx_nand_suspend,
1005 .name = LPC32XX_MODNAME,
1006 .of_match_table = lpc32xx_nand_match,
1010 module_platform_driver(lpc32xx_nand_driver);
1012 MODULE_LICENSE("GPL");
1013 MODULE_AUTHOR("Kevin Wells <kevin.wells@nxp.com>");
1014 MODULE_AUTHOR("Roland Stigge <stigge@antcom.de>");
1015 MODULE_DESCRIPTION("NAND driver for the NXP LPC32XX SLC controller");