1 # SPDX-License-Identifier: GPL-2.0-only
2 config LEDS_GPIO_REGISTER
5 This option provides the function gpio_led_register_device.
6 As this function is used by arch code it must not be compiled as a
12 Say Y to enable Linux LED support. This allows control of supported
13 LEDs from both userspace and optionally, by kernel events (triggers).
18 tristate "LED Class Support"
20 This option enables the LED sysfs class in /sys/class/leds. You'll
21 need this to do anything useful with LEDs. If unsure, say Y.
23 config LEDS_CLASS_FLASH
24 tristate "LED Flash Class Support"
27 This option enables the flash LED sysfs class in /sys/class/leds.
28 It wraps LED Class and adds flash LEDs specific sysfs attributes
29 and kernel internal API to it. You'll need this to provide support
30 for the flash related features of a LED device. It can be built
33 config LEDS_CLASS_MULTICOLOR
34 tristate "LED Multicolor Class Support"
37 This option enables the multicolor LED sysfs class in /sys/class/leds.
38 It wraps LED class and adds multicolor LED specific sysfs attributes
39 and kernel internal API to it. You'll need this to provide support
40 for multicolor LEDs that are grouped together. This class is not
41 intended for single color LEDs. It can be built as a module.
43 config LEDS_BRIGHTNESS_HW_CHANGED
44 bool "LED Class brightness_hw_changed attribute support"
47 This option enables support for the brightness_hw_changed attribute
48 for LED sysfs class devices under /sys/class/leds.
50 See Documentation/ABI/testing/sysfs-class-led for details.
55 tristate "LED Support for Marvell 88PM860x PMIC"
57 depends on MFD_88PM860X
59 This option enables support for on-chip LED drivers found on Marvell
60 Semiconductor 88PM8606 PMIC.
63 tristate "LED support for Panasonic AN30259A"
64 depends on LEDS_CLASS && I2C && OF
66 This option enables support for the AN30259A 3-channel
69 To compile this driver as a module, choose M here: the module
70 will be called leds-an30259a.
73 tristate "Front panel LED support for PC Engines APU/APU2/APU3 boards"
77 This driver makes the PC Engines APU1 front panel LEDs
78 accessible from userspace programs through the LED subsystem.
80 If you're looking for APU2/3, use the pcengines-apu2 driver.
81 (symbol CONFIG_PCENGINES_APU2)
83 To compile this driver as a module, choose M here: the
84 module will be called leds-apu.
87 tristate "Dell Wyse 3020 status LED support"
89 depends on (MACH_MMP3_DT && MFD_ENE_KB3930) || COMPILE_TEST
91 This driver adds support for controlling the front panel status
92 LEDs on Dell Wyse 3020 (Ariel) board via the KB3930 Embedded
95 Say Y to if your machine is a Dell Wyse 3020 thin client.
98 tristate "LED support for Awinic AW2013"
99 depends on LEDS_CLASS && I2C && OF
101 This option enables support for the AW2013 3-channel
104 To compile this driver as a module, choose M here: the module
105 will be called leds-aw2013.
108 tristate "LED Support for Broadcom BCM6328"
109 depends on LEDS_CLASS
113 This option enables support for LEDs connected to the BCM6328
114 LED HW controller accessed via MMIO registers.
117 tristate "LED Support for Broadcom BCM6358"
118 depends on LEDS_CLASS
122 This option enables support for LEDs connected to the BCM6358
123 LED HW controller accessed via MMIO registers.
126 tristate "LED Support for Motorola CPCAP"
127 depends on LEDS_CLASS
131 This option enables support for LEDs offered by Motorola's
134 config LEDS_CR0014114
135 tristate "LED Support for Crane CR0014114"
136 depends on LEDS_CLASS
140 This option enables support for CR0014114 LED Board which
141 is widely used in vending machines produced by
142 Crane Merchandising Systems.
144 To compile this driver as a module, choose M here: the module
145 will be called leds-cr0014114.
147 config LEDS_EL15203000
148 tristate "LED Support for Crane EL15203000"
149 depends on LEDS_CLASS
153 This option enables support for EL15203000 LED Board
154 (aka RED LED board) which is widely used in coffee vending
155 machines produced by Crane Merchandising Systems.
157 To compile this driver as a module, choose M here: the module
158 will be called leds-el15203000.
160 config LEDS_TURRIS_OMNIA
161 tristate "LED support for CZ.NIC's Turris Omnia"
162 depends on LEDS_CLASS_MULTICOLOR
164 depends on MACH_ARMADA_38X || COMPILE_TEST
167 This option enables basic support for the LEDs found on the front
168 side of CZ.NIC's Turris Omnia router. There are 12 RGB LEDs on the
172 tristate "LCD Backlight driver for LM3530"
173 depends on LEDS_CLASS
176 This option enables support for the LCD backlight using
177 LM3530 ambient light sensor chip. This ALS chip can be
178 controlled manually or using PWM input or using ambient
182 tristate "LCD Backlight driver for LM3532"
184 depends on LEDS_CLASS
187 This option enables support for the LCD backlight using
188 LM3532 ambient light sensor chip. This ALS chip can be
189 controlled manually or using PWM input or using ambient
193 tristate "LED support for LM3533"
194 depends on LEDS_CLASS
195 depends on MFD_LM3533
197 This option enables support for the LEDs on National Semiconductor /
198 TI LM3533 Lighting Power chips.
200 The LEDs can be controlled directly, through PWM input, or by the
201 ambient-light-sensor interface. The chip supports
202 hardware-accelerated blinking with maximum on and off periods of 9.8
203 and 77 seconds respectively.
206 tristate "LED support for LM3642 Chip"
207 depends on LEDS_CLASS && I2C
210 This option enables support for LEDs connected to LM3642.
211 The LM3642 is a 4MHz fixed-frequency synchronous boost
212 converter plus 1.5A constant current driver for a high-current
216 tristate "LED support for LM3692x Chips"
217 depends on LEDS_CLASS && I2C && OF
220 This option enables support for the TI LM3692x family
221 of white LED string drivers used for backlighting.
224 tristate "LED Support for Locomo device"
225 depends on LEDS_CLASS
226 depends on SHARP_LOCOMO
228 This option enables support for the LEDs on Sharp Locomo.
229 Zaurus models SL-5500 and SL-5600.
231 config LEDS_MIKROTIK_RB532
232 tristate "LED Support for Mikrotik Routerboard 532"
233 depends on LEDS_CLASS
234 depends on MIKROTIK_RB532
236 This option enables support for the so called "User LED" of
237 Mikrotik's Routerboard 532.
240 tristate "LED Support for Mediatek MT6323 PMIC"
241 depends on LEDS_CLASS
242 depends on MFD_MT6397
244 This option enables support for on-chip LED drivers found on
245 Mediatek MT6323 PMIC.
248 tristate "LED Support for Soekris net48xx series Error LED"
249 depends on LEDS_CLASS
250 depends on SCx200_GPIO
252 This option enables support for the Soekris net4801 and net4826 error
256 tristate "LED Support for the WRAP series LEDs"
257 depends on LEDS_CLASS
258 depends on SCx200_GPIO
260 This option enables support for the PCEngines WRAP programmable LEDs.
262 config LEDS_COBALT_QUBE
263 tristate "LED Support for the Cobalt Qube series front LED"
264 depends on LEDS_CLASS
265 depends on MIPS_COBALT || COMPILE_TEST
267 This option enables support for the front LED on Cobalt Qube series
269 config LEDS_COBALT_RAQ
270 bool "LED Support for the Cobalt Raq series"
271 depends on LEDS_CLASS=y && (MIPS_COBALT || COMPILE_TEST)
274 This option enables support for the Cobalt Raq series LEDs.
277 tristate "LED support for SunFire servers."
278 depends on LEDS_CLASS
282 This option enables support for the Left, Middle, and Right
283 LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.
285 config LEDS_IPAQ_MICRO
286 tristate "LED Support for the Compaq iPAQ h3xxx"
287 depends on LEDS_CLASS
288 depends on MFD_IPAQ_MICRO
290 Choose this option if you want to use the notification LED on
291 Compaq/HP iPAQ h3100 and h3600.
294 tristate "LED Support for the HP Jornada 6xx"
295 depends on LEDS_CLASS
298 This option enables LED support for the handheld
299 HP Jornada 620/660/680/690.
302 tristate "LED driver for PCA9532 dimmer"
303 depends on LEDS_CLASS
304 depends on I2C && INPUT
306 This option enables support for NXP pca9532
307 LED controller. It is generally only useful
310 config LEDS_PCA9532_GPIO
311 bool "Enable GPIO support for PCA9532"
312 depends on LEDS_PCA9532
315 Allow unused pins on PCA9532 to be used as gpio.
317 To use a pin as gpio pca9532_type in pca9532_platform data needs to
318 set to PCA9532_TYPE_GPIO.
321 tristate "LED Support for GPIO connected LEDs"
322 depends on LEDS_CLASS
323 depends on GPIOLIB || COMPILE_TEST
325 This option enables support for the LEDs connected to GPIO
326 outputs. To be useful the particular board must have LEDs
327 and they must be connected to the GPIO lines. The LEDs must be
328 defined as platform devices and/or OpenFirmware platform devices.
329 The code to use these bindings can be selected below.
332 tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
333 depends on LEDS_CLASS
336 This option enables support for LEDs connected to the National
337 Semiconductor LP3944 Lighting Management Unit (LMU) also known as
340 To compile this driver as a module, choose M here: the
341 module will be called leds-lp3944.
344 tristate "LED Support for TI LP3952 2 channel LED driver"
345 depends on LEDS_CLASS
350 This option enables support for LEDs connected to the Texas
351 Instruments LP3952 LED driver.
353 To compile this driver as a module, choose M here: the
354 module will be called leds-lp3952.
357 tristate "LED Support for TI LP5036/30/24/18/12/09 LED driver chip"
358 depends on LEDS_CLASS && REGMAP_I2C
359 depends on LEDS_CLASS_MULTICOLOR || !LEDS_CLASS_MULTICOLOR
361 If you say yes here you get support for the Texas Instruments
362 LP5036, LP5030, LP5024, LP5018, LP5012 and LP5009 LED driver.
364 To compile this driver as a module, choose M here: the
365 module will be called leds-lp50xx.
367 config LEDS_LP55XX_COMMON
368 tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
369 depends on LEDS_CLASS
370 depends on LEDS_CLASS_MULTICOLOR || !LEDS_CLASS_MULTICOLOR
374 select FW_LOADER_USER_HELPER
376 This option supports common operations for LP5521/5523/55231/5562/8501
380 tristate "LED Support for N.S. LP5521 LED driver chip"
381 depends on LEDS_CLASS && I2C
382 depends on LEDS_LP55XX_COMMON
384 If you say yes here you get support for the National Semiconductor
385 LP5521 LED driver. It is 3 channel chip with programmable engines.
386 Driver provides direct control via LED class and interface for
387 programming the engines.
390 tristate "LED Support for TI/National LP5523/55231 LED driver chip"
391 depends on LEDS_CLASS && I2C
392 depends on LEDS_LP55XX_COMMON
394 If you say yes here you get support for TI/National Semiconductor
395 LP5523/55231 LED driver.
396 It is 9 channel chip with programmable engines.
397 Driver provides direct control via LED class and interface for
398 programming the engines.
401 tristate "LED Support for TI LP5562 LED driver chip"
402 depends on LEDS_CLASS && I2C
403 depends on LEDS_LP55XX_COMMON
405 If you say yes here you get support for TI LP5562 LED driver.
406 It is 4 channels chip with programmable engines.
407 Driver provides direct control via LED class and interface for
408 programming the engines.
411 tristate "LED Support for TI LP8501 LED driver chip"
412 depends on LEDS_CLASS && I2C
413 depends on LEDS_LP55XX_COMMON
415 If you say yes here you get support for TI LP8501 LED driver.
416 It is 9 channel chip with programmable engines.
417 Driver provides direct control via LED class and interface for
418 programming the engines.
419 It is similar as LP5523, but output power selection is available.
420 And register layout and engine program schemes are different.
423 tristate "LED support for the TI LP8788 PMIC"
424 depends on LEDS_CLASS
425 depends on MFD_LP8788
427 This option enables support for the Keyboard LEDs on the LP8788 PMIC.
430 tristate "LED support for the TI LP8860 4 channel LED driver"
431 depends on LEDS_CLASS && I2C && OF
434 If you say yes here you get support for the TI LP8860 4 channel
436 This option enables support for the display cluster LEDs
437 on the LP8860 4 channel LED driver using the I2C communication
440 config LEDS_CLEVO_MAIL
441 tristate "Mail LED on Clevo notebook"
442 depends on LEDS_CLASS && BROKEN
443 depends on X86 && SERIO_I8042 && DMI
445 This driver makes the mail LED accessible from userspace
446 programs through the LEDs subsystem. This LED has three
447 known modes: off, blink at 0.5Hz and blink at 1Hz.
449 The driver supports two kinds of interface: using ledtrig-timer
450 or through /sys/class/leds/clevo::mail/brightness. As this LED
451 cannot change its brightness it blinks instead. The brightness
452 value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
455 This module can drive the mail LED for the following notebooks:
460 Clevo D400V/D470V (not tested, but might work)
462 Clevo M5x0N (not tested, but might work)
463 Positivo Mobile (Clevo M5x0V)
465 If your model is not listed here you can try the "nodetect"
468 To compile this driver as a module, choose M here: the
469 module will be called leds-clevo-mail.
472 tristate "LED Support for PCA955x I2C chips"
473 depends on LEDS_CLASS
476 This option enables support for LEDs connected to PCA955x
477 LED driver chips accessed via the I2C bus. Supported
478 devices include PCA9550, PCA9551, PCA9552, and PCA9553.
480 config LEDS_PCA955X_GPIO
481 bool "Enable GPIO support for PCA955X"
482 depends on LEDS_PCA955X
485 Allow unused pins on PCA955X to be used as gpio.
487 To use a pin as gpio the pin type should be set to
488 PCA955X_TYPE_GPIO in the device tree.
492 tristate "LED support for PCA963x I2C chip"
493 depends on LEDS_CLASS
496 This option enables support for LEDs connected to the PCA963x
497 LED driver chip accessed via the I2C bus. Supported
498 devices include PCA9633 and PCA9634
500 config LEDS_WM831X_STATUS
501 tristate "LED support for status LEDs on WM831x PMICs"
502 depends on LEDS_CLASS
503 depends on MFD_WM831X
505 This option enables support for the status LEDs of the WM831x
509 tristate "LED Support for WM8350 AudioPlus PMIC"
510 depends on LEDS_CLASS
511 depends on MFD_WM8350
513 This option enables support for LEDs driven by the Wolfson
514 Microelectronics WM8350 AudioPlus PMIC.
517 tristate "LED Support for DA9030/DA9034 PMIC"
518 depends on LEDS_CLASS
519 depends on PMIC_DA903X
521 This option enables support for on-chip LED drivers found
522 on Dialog Semiconductor DA9030/DA9034 PMICs.
525 tristate "Dialog DA9052/DA9053 LEDS"
526 depends on LEDS_CLASS
527 depends on PMIC_DA9052
529 This option enables support for on-chip LED drivers found
530 on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
532 config LEDS_DAC124S085
533 tristate "LED Support for DAC124S085 SPI DAC"
534 depends on LEDS_CLASS
537 This option enables support for DAC124S085 SPI DAC from NatSemi,
538 which can be used to control up to four LEDs.
541 tristate "PWM driven LED Support"
542 depends on LEDS_CLASS
545 This option enables support for pwm driven LEDs
547 config LEDS_REGULATOR
548 tristate "REGULATOR driven LED support"
549 depends on LEDS_CLASS
552 This option enables support for regulator driven LEDs.
555 tristate "LED driver for BD2802 RGB LED"
556 depends on LEDS_CLASS
559 This option enables support for BD2802GU RGB LED driver chips
560 accessed via the I2C bus.
562 config LEDS_INTEL_SS4200
563 tristate "LED driver for Intel NAS SS4200 series"
564 depends on LEDS_CLASS
565 depends on PCI && DMI
568 This option enables support for the Intel SS4200 series of
569 Network Attached Storage servers. You may control the hard
570 drive or power LEDs on the front panel. Using this driver
571 can stop the front LED from blinking after startup.
574 tristate "LED driver for LT3593 controllers"
575 depends on LEDS_CLASS
576 depends on GPIOLIB || COMPILE_TEST
578 This option enables support for LEDs driven by a Linear Technology
579 LT3593 controller. This controller uses a special one-wire pulse
580 coding protocol to set the brightness.
583 tristate "LED Support for ADP5520/ADP5501 PMIC"
584 depends on LEDS_CLASS
585 depends on PMIC_ADP5520
587 This option enables support for on-chip LED drivers found
588 on Analog Devices ADP5520/ADP5501 PMICs.
590 To compile this driver as a module, choose M here: the module will
591 be called leds-adp5520.
594 tristate "LED Support for MC13XXX PMIC"
595 depends on LEDS_CLASS
596 depends on MFD_MC13XXX
598 This option enables support for on-chip LED drivers found
599 on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC.
602 tristate "LED support for Network Space v2 GPIO LEDs"
603 depends on LEDS_CLASS
604 depends on MACH_KIRKWOOD || MACH_ARMADA_370 || COMPILE_TEST
607 This option enables support for the dual-GPIO LEDs found on the
608 following LaCie/Seagate boards:
610 Network Space v2 (and parents: Max, Mini)
613 n090401 (Seagate NAS 4-Bay)
616 tristate "LED support for Big Network series LEDs"
617 depends on LEDS_CLASS
618 depends on MACH_KIRKWOOD || COMPILE_TEST
622 This option enables support for LEDs found on the LaCie 2Big
623 and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
624 controlled through a GPIO extension bus.
627 bool "LED support for the HTC ASIC3"
628 depends on LEDS_CLASS=y
632 This option enables support for the LEDs on the HTC ASIC3. The HTC
633 ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
634 cannot be used. This driver supports hardware blinking with an on+off
635 period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.
638 tristate "LED Support for TCA6507 I2C chip"
639 depends on LEDS_CLASS && I2C
641 This option enables support for LEDs connected to TC6507
642 LED driver chips accessed via the I2C bus.
643 Driver support brightness control and hardware-assisted blinking.
646 tristate "LED driver for TLC59108 and TLC59116 controllers"
647 depends on LEDS_CLASS && I2C
650 This option enables support for Texas Instruments TLC59108
651 and TLC59116 LED controllers.
654 tristate "LED support for Maxim MAX77650 PMIC"
655 depends on LEDS_CLASS && MFD_MAX77650
657 LEDs driver for MAX77650 family of PMICs from Maxim Integrated.
660 tristate "LED support for MAX8997 PMIC"
661 depends on LEDS_CLASS && MFD_MAX8997
663 This option enables support for on-chip LED drivers on
667 tristate "LED support for LM3554 and LM3556 chips"
668 depends on LEDS_CLASS && I2C
671 This option enables support for LEDs connected to LM3554
672 and LM3556. It includes Torch, Flash and Indicator functions.
675 tristate "LED support for the Bachmann OT200"
676 depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST)
678 This option enables support for the LEDs on the Bachmann OT200.
679 Say Y to enable LEDs on the Bachmann OT200.
681 config LEDS_MENF21BMC
682 tristate "LED support for the MEN 14F021P00 BMC"
683 depends on LEDS_CLASS && MFD_MENF21BMC
685 Say Y here to include support for the MEN 14F021P00 BMC LEDs.
687 This driver can also be built as a module. If so the module
688 will be called leds-menf21bmc.
690 config LEDS_IS31FL319X
691 tristate "LED Support for ISSI IS31FL319x I2C LED controller family"
692 depends on LEDS_CLASS && I2C
695 This option enables support for LEDs connected to ISSI IS31FL319x
696 fancy LED driver chips accessed via the I2C bus.
697 Driver supports individual PWM brightness control for each channel.
699 This driver can also be built as a module. If so the module will be
700 called leds-is31fl319x.
702 config LEDS_IS31FL32XX
703 tristate "LED support for ISSI IS31FL32XX I2C LED controller family"
704 depends on LEDS_CLASS && I2C && OF
706 Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
707 LED controllers. They are I2C devices with multiple constant-current
708 channels, each with independent 256-level PWM control.
710 config LEDS_SC27XX_BLTC
711 tristate "LED support for the SC27xx breathing light controller"
712 depends on LEDS_CLASS && MFD_SC27XX_PMIC
715 Say Y here to include support for the SC27xx breathing light controller
718 This driver can also be built as a module. If so the module will be
719 called leds-sc27xx-bltc.
721 comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)"
724 tristate "LED support for the BlinkM I2C RGB LED"
725 depends on LEDS_CLASS
728 This option enables support for the BlinkM RGB LED connected
729 through I2C. Say Y to enable support for the BlinkM LED.
732 tristate "LED support for PowerNV Platform"
733 depends on LEDS_CLASS
734 depends on PPC_POWERNV
737 This option enables support for the system LEDs present on
738 PowerNV platforms. Say 'y' to enable this support in kernel.
739 To compile this driver as a module, choose 'm' here: the module
740 will be called leds-powernv.
743 bool "LED support for LEDs on system controllers"
744 depends on LEDS_CLASS=y
745 depends on MFD_SYSCON
748 This option enables support for the LEDs on syscon type
749 devices. This will only work with device tree enabled
753 tristate "LED Support for the Qualcomm PM8058 PMIC"
754 depends on MFD_PM8XXX
755 depends on LEDS_CLASS
757 Choose this option if you want to use the LED drivers in
758 the Qualcomm PM8058 PMIC.
761 tristate "LED support for the Mellanox boards"
762 depends on X86 && DMI
763 depends on LEDS_CLASS
765 This option enables support for the LEDs on the Mellanox
766 boards. Say Y to enable these.
769 tristate "LED support for the Mellanox switches management control"
770 depends on LEDS_CLASS
772 This option enables support for the LEDs on the Mellanox Ethernet and
773 InfiniBand switches. The driver can be activated by the platform device
774 device add call. Say Y to enable these. To compile this driver as a
775 module, choose 'M' here: the module will be called leds-mlxreg.
778 tristate "Userspace LED support"
779 depends on LEDS_CLASS
781 This option enables support for userspace LEDs. Say 'y' to enable this
782 support in kernel. To compile this driver as a module, choose 'm' here:
783 the module will be called uleds.
786 tristate "LED support for NI PXI NIC78bx devices"
787 depends on LEDS_CLASS
788 depends on X86 && ACPI
790 This option enables support for the User1 and User2 LEDs on NI
793 To compile this driver as a module, choose M here: the module
794 will be called leds-nic78bx.
797 tristate "LED support for SPI LED controller with a single byte"
798 depends on LEDS_CLASS
802 This option enables support for LED controller which use a single byte
803 for controlling the brightness. Currently the following controller is
804 supported: Ubiquiti airCube ISP microcontroller based LED controller.
806 config LEDS_TI_LMU_COMMON
807 tristate "LED driver for TI LMU"
808 depends on LEDS_CLASS
811 Say Y to enable the LED driver for TI LMU devices.
812 This supports common features between the TI LM3532, LM3631, LM3632,
813 LM3633, LM3695 and LM3697.
816 tristate "LED driver for LM3697"
817 depends on LEDS_TI_LMU_COMMON
820 Say Y to enable the LM3697 LED driver for TI LMU devices.
821 This supports the LED device LM3697.
824 tristate "LED driver for LM36274"
825 depends on LEDS_TI_LMU_COMMON
826 depends on MFD_TI_LMU
828 Say Y to enable the LM36274 LED driver for TI LMU devices.
829 This supports the LED device LM36274.
832 tristate "LED support for TI TPS6105X"
833 depends on LEDS_CLASS
835 default y if TPS6105X
837 This driver supports TPS61050/TPS61052 LED chips.
838 It is a single boost converter primarily for white LEDs and
842 tristate "LED support for SGI Octane machines"
843 depends on LEDS_CLASS
844 depends on SGI_MFD_IOC3 || COMPILE_TEST
846 This option enables support for the Red and White LEDs of
849 To compile this driver as a module, choose M here: the module
850 will be called leds-ip30.
852 config LEDS_ACER_A500
853 tristate "Power button LED support for Acer Iconia Tab A500"
854 depends on LEDS_CLASS && MFD_ACER_A500_EC
856 This option enables support for the Power Button LED of
857 Acer Iconia Tab A500.
859 source "drivers/leds/blink/Kconfig"
861 comment "Flash and Torch LED drivers"
862 source "drivers/leds/flash/Kconfig"
864 comment "RGB LED drivers"
865 source "drivers/leds/rgb/Kconfig"
867 comment "LED Triggers"
868 source "drivers/leds/trigger/Kconfig"
870 comment "Simple LED drivers"
871 source "drivers/leds/simple/Kconfig"