2 * Copyright(c) 2015 - 2017 Intel Corporation.
4 * This file is provided under a dual BSD/GPLv2 license. When using or
5 * redistributing this file, you may do so under either license.
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of version 2 of the GNU General Public License as
11 * published by the Free Software Foundation.
13 * This program is distributed in the hope that it will be useful, but
14 * WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
16 * General Public License for more details.
20 * Redistribution and use in source and binary forms, with or without
21 * modification, are permitted provided that the following conditions
24 * - Redistributions of source code must retain the above copyright
25 * notice, this list of conditions and the following disclaimer.
26 * - Redistributions in binary form must reproduce the above copyright
27 * notice, this list of conditions and the following disclaimer in
28 * the documentation and/or other materials provided with the
30 * - Neither the name of Intel Corporation nor the names of its
31 * contributors may be used to endorse or promote products derived
32 * from this software without specific prior written permission.
34 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
35 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
36 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
37 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
38 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
39 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
40 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
41 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
42 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
43 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
44 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
48 #include <linux/pci.h>
50 #include <linux/delay.h>
51 #include <linux/vmalloc.h>
52 #include <linux/aer.h>
53 #include <linux/module.h>
56 #include "chip_registers.h"
60 * This file contains PCIe utility routines.
64 * Code to adjust PCIe capabilities.
66 static void tune_pcie_caps(struct hfi1_devdata *);
69 * Do all the common PCIe setup and initialization.
70 * devdata is not yet allocated, and is not allocated until after this
71 * routine returns success. Therefore dd_dev_err() can't be used for error
74 int hfi1_pcie_init(struct pci_dev *pdev, const struct pci_device_id *ent)
78 ret = pci_enable_device(pdev);
81 * This can happen (in theory) iff:
82 * We did a chip reset, and then failed to reprogram the
83 * BAR, or the chip reset due to an internal error. We then
84 * unloaded the driver and reloaded it.
86 * Both reset cases set the BAR back to initial state. For
87 * the latter case, the AER sticky error bit at offset 0x718
88 * should be set, but the Linux kernel doesn't yet know
89 * about that, it appears. If the original BAR was retained
90 * in the kernel data structures, this may be OK.
92 hfi1_early_err(&pdev->dev, "pci enable failed: error %d\n",
97 ret = pci_request_regions(pdev, DRIVER_NAME);
99 hfi1_early_err(&pdev->dev,
100 "pci_request_regions fails: err %d\n", -ret);
104 ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
107 * If the 64 bit setup fails, try 32 bit. Some systems
108 * do not setup 64 bit maps on systems with 2GB or less
111 ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
113 hfi1_early_err(&pdev->dev,
114 "Unable to set DMA mask: %d\n", ret);
117 ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
119 ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
122 hfi1_early_err(&pdev->dev,
123 "Unable to set DMA consistent mask: %d\n", ret);
127 pci_set_master(pdev);
128 (void)pci_enable_pcie_error_reporting(pdev);
132 hfi1_pcie_cleanup(pdev);
138 * Clean what was done in hfi1_pcie_init()
140 void hfi1_pcie_cleanup(struct pci_dev *pdev)
142 pci_disable_device(pdev);
144 * Release regions should be called after the disable. OK to
145 * call if request regions has not been called or failed.
147 pci_release_regions(pdev);
151 * Do remaining PCIe setup, once dd is allocated, and save away
152 * fields required to re-initialize after a chip reset, or for
153 * various other purposes
155 int hfi1_pcie_ddinit(struct hfi1_devdata *dd, struct pci_dev *pdev)
158 resource_size_t addr;
162 addr = pci_resource_start(pdev, 0);
163 len = pci_resource_len(pdev, 0);
166 * The TXE PIO buffers are at the tail end of the chip space.
167 * Cut them off and map them separately.
170 /* sanity check vs expectations */
171 if (len != TXE_PIO_SEND + TXE_PIO_SIZE) {
172 dd_dev_err(dd, "chip PIO range does not match\n");
176 dd->kregbase1 = ioremap_nocache(addr, RCV_ARRAY);
177 if (!dd->kregbase1) {
178 dd_dev_err(dd, "UC mapping of kregbase1 failed\n");
181 dd_dev_info(dd, "UC base1: %p for %x\n", dd->kregbase1, RCV_ARRAY);
183 /* verify that reads actually work, save revision for reset check */
184 dd->revision = readq(dd->kregbase1 + CCE_REVISION);
185 if (dd->revision == ~(u64)0) {
186 dd_dev_err(dd, "Cannot read chip CSRs\n");
190 rcv_array_count = readq(dd->kregbase1 + RCV_ARRAY_CNT);
191 dd_dev_info(dd, "RcvArray count: %u\n", rcv_array_count);
192 dd->base2_start = RCV_ARRAY + rcv_array_count * 8;
194 dd->kregbase2 = ioremap_nocache(
195 addr + dd->base2_start,
196 TXE_PIO_SEND - dd->base2_start);
197 if (!dd->kregbase2) {
198 dd_dev_err(dd, "UC mapping of kregbase2 failed\n");
201 dd_dev_info(dd, "UC base2: %p for %x\n", dd->kregbase2,
202 TXE_PIO_SEND - dd->base2_start);
204 dd->piobase = ioremap_wc(addr + TXE_PIO_SEND, TXE_PIO_SIZE);
206 dd_dev_err(dd, "WC mapping of send buffers failed\n");
209 dd_dev_info(dd, "WC piobase: %p\n for %x", dd->piobase, TXE_PIO_SIZE);
211 dd->physaddr = addr; /* used for io_remap, etc. */
214 * Map the chip's RcvArray as write-combining to allow us
215 * to write an entire cacheline worth of entries in one shot.
217 dd->rcvarray_wc = ioremap_wc(addr + RCV_ARRAY,
218 rcv_array_count * 8);
219 if (!dd->rcvarray_wc) {
220 dd_dev_err(dd, "WC mapping of receive array failed\n");
223 dd_dev_info(dd, "WC RcvArray: %p for %x\n",
224 dd->rcvarray_wc, rcv_array_count * 8);
226 dd->flags |= HFI1_PRESENT; /* chip.c CSR routines now work */
230 hfi1_pcie_ddcleanup(dd);
235 * Do PCIe cleanup related to dd, after chip-specific cleanup, etc. Just prior
236 * to releasing the dd memory.
237 * Void because all of the core pcie cleanup functions are void.
239 void hfi1_pcie_ddcleanup(struct hfi1_devdata *dd)
241 dd->flags &= ~HFI1_PRESENT;
243 iounmap(dd->kregbase1);
244 dd->kregbase1 = NULL;
246 iounmap(dd->kregbase2);
247 dd->kregbase2 = NULL;
249 iounmap(dd->rcvarray_wc);
250 dd->rcvarray_wc = NULL;
252 iounmap(dd->piobase);
256 /* return the PCIe link speed from the given link status */
257 static u32 extract_speed(u16 linkstat)
261 switch (linkstat & PCI_EXP_LNKSTA_CLS) {
262 default: /* not defined, assume Gen1 */
263 case PCI_EXP_LNKSTA_CLS_2_5GB:
264 speed = 2500; /* Gen 1, 2.5GHz */
266 case PCI_EXP_LNKSTA_CLS_5_0GB:
267 speed = 5000; /* Gen 2, 5GHz */
269 case PCI_EXP_LNKSTA_CLS_8_0GB:
270 speed = 8000; /* Gen 3, 8GHz */
276 /* return the PCIe link speed from the given link status */
277 static u32 extract_width(u16 linkstat)
279 return (linkstat & PCI_EXP_LNKSTA_NLW) >> PCI_EXP_LNKSTA_NLW_SHIFT;
282 /* read the link status and set dd->{lbus_width,lbus_speed,lbus_info} */
283 static void update_lbus_info(struct hfi1_devdata *dd)
288 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKSTA, &linkstat);
290 dd_dev_err(dd, "Unable to read from PCI config\n");
294 dd->lbus_width = extract_width(linkstat);
295 dd->lbus_speed = extract_speed(linkstat);
296 snprintf(dd->lbus_info, sizeof(dd->lbus_info),
297 "PCIe,%uMHz,x%u", dd->lbus_speed, dd->lbus_width);
301 * Read in the current PCIe link width and speed. Find if the link is
304 int pcie_speeds(struct hfi1_devdata *dd)
307 struct pci_dev *parent = dd->pcidev->bus->self;
310 if (!pci_is_pcie(dd->pcidev)) {
311 dd_dev_err(dd, "Can't find PCI Express capability!\n");
315 /* find if our max speed is Gen3 and parent supports Gen3 speeds */
316 dd->link_gen3_capable = 1;
318 ret = pcie_capability_read_dword(dd->pcidev, PCI_EXP_LNKCAP, &linkcap);
320 dd_dev_err(dd, "Unable to read from PCI config\n");
324 if ((linkcap & PCI_EXP_LNKCAP_SLS) != PCI_EXP_LNKCAP_SLS_8_0GB) {
326 "This HFI is not Gen3 capable, max speed 0x%x, need 0x3\n",
327 linkcap & PCI_EXP_LNKCAP_SLS);
328 dd->link_gen3_capable = 0;
332 * bus->max_bus_speed is set from the bridge's linkcap Max Link Speed
334 if (parent && dd->pcidev->bus->max_bus_speed != PCIE_SPEED_8_0GT) {
335 dd_dev_info(dd, "Parent PCIe bridge does not support Gen3\n");
336 dd->link_gen3_capable = 0;
339 /* obtain the link width and current speed */
340 update_lbus_info(dd);
342 dd_dev_info(dd, "%s\n", dd->lbus_info);
349 * - actual number of interrupts allocated or
352 int request_msix(struct hfi1_devdata *dd, u32 msireq)
356 nvec = pci_alloc_irq_vectors(dd->pcidev, msireq, msireq, PCI_IRQ_MSIX);
358 dd_dev_err(dd, "pci_alloc_irq_vectors() failed: %d\n", nvec);
367 /* restore command and BARs after a reset has wiped them out */
368 int restore_pci_variables(struct hfi1_devdata *dd)
372 ret = pci_write_config_word(dd->pcidev, PCI_COMMAND, dd->pci_command);
376 ret = pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_0,
381 ret = pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_1,
386 ret = pci_write_config_dword(dd->pcidev, PCI_ROM_ADDRESS, dd->pci_rom);
390 ret = pcie_capability_write_word(dd->pcidev, PCI_EXP_DEVCTL,
395 ret = pcie_capability_write_word(dd->pcidev, PCI_EXP_LNKCTL,
400 ret = pcie_capability_write_word(dd->pcidev, PCI_EXP_DEVCTL2,
405 ret = pci_write_config_dword(dd->pcidev, PCI_CFG_MSIX0, dd->pci_msix0);
409 if (pci_find_ext_capability(dd->pcidev, PCI_EXT_CAP_ID_TPH)) {
410 ret = pci_write_config_dword(dd->pcidev, PCIE_CFG_TPH2,
418 dd_dev_err(dd, "Unable to write to PCI config\n");
422 /* Save BARs and command to rewrite after device reset */
423 int save_pci_variables(struct hfi1_devdata *dd)
427 ret = pci_read_config_dword(dd->pcidev, PCI_BASE_ADDRESS_0,
432 ret = pci_read_config_dword(dd->pcidev, PCI_BASE_ADDRESS_1,
437 ret = pci_read_config_dword(dd->pcidev, PCI_ROM_ADDRESS, &dd->pci_rom);
441 ret = pci_read_config_word(dd->pcidev, PCI_COMMAND, &dd->pci_command);
445 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVCTL,
450 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKCTL,
455 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVCTL2,
460 ret = pci_read_config_dword(dd->pcidev, PCI_CFG_MSIX0, &dd->pci_msix0);
464 if (pci_find_ext_capability(dd->pcidev, PCI_EXT_CAP_ID_TPH)) {
465 ret = pci_read_config_dword(dd->pcidev, PCIE_CFG_TPH2,
473 dd_dev_err(dd, "Unable to read from PCI config\n");
478 * BIOS may not set PCIe bus-utilization parameters for best performance.
479 * Check and optionally adjust them to maximize our throughput.
481 static int hfi1_pcie_caps;
482 module_param_named(pcie_caps, hfi1_pcie_caps, int, S_IRUGO);
483 MODULE_PARM_DESC(pcie_caps, "Max PCIe tuning: Payload (0..3), ReadReq (4..7)");
485 uint aspm_mode = ASPM_MODE_DISABLED;
486 module_param_named(aspm, aspm_mode, uint, S_IRUGO);
487 MODULE_PARM_DESC(aspm, "PCIe ASPM: 0: disable, 1: enable, 2: dynamic");
489 static void tune_pcie_caps(struct hfi1_devdata *dd)
491 struct pci_dev *parent;
492 u16 rc_mpss, rc_mps, ep_mpss, ep_mps;
493 u16 rc_mrrs, ep_mrrs, max_mrrs, ectl;
497 * Turn on extended tags in DevCtl in case the BIOS has turned it off
498 * to improve WFR SDMA bandwidth
500 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVCTL, &ectl);
501 if ((!ret) && !(ectl & PCI_EXP_DEVCTL_EXT_TAG)) {
502 dd_dev_info(dd, "Enabling PCIe extended tags\n");
503 ectl |= PCI_EXP_DEVCTL_EXT_TAG;
504 ret = pcie_capability_write_word(dd->pcidev,
505 PCI_EXP_DEVCTL, ectl);
507 dd_dev_info(dd, "Unable to write to PCI config\n");
509 /* Find out supported and configured values for parent (root) */
510 parent = dd->pcidev->bus->self;
512 * The driver cannot perform the tuning if it does not have
513 * access to the upstream component.
516 dd_dev_info(dd, "Parent not found\n");
519 if (!pci_is_root_bus(parent->bus)) {
520 dd_dev_info(dd, "Parent not root\n");
523 if (!pci_is_pcie(parent)) {
524 dd_dev_info(dd, "Parent is not PCI Express capable\n");
527 if (!pci_is_pcie(dd->pcidev)) {
528 dd_dev_info(dd, "PCI device is not PCI Express capable\n");
531 rc_mpss = parent->pcie_mpss;
532 rc_mps = ffs(pcie_get_mps(parent)) - 8;
533 /* Find out supported and configured values for endpoint (us) */
534 ep_mpss = dd->pcidev->pcie_mpss;
535 ep_mps = ffs(pcie_get_mps(dd->pcidev)) - 8;
537 /* Find max payload supported by root, endpoint */
538 if (rc_mpss > ep_mpss)
541 /* If Supported greater than limit in module param, limit it */
542 if (rc_mpss > (hfi1_pcie_caps & 7))
543 rc_mpss = hfi1_pcie_caps & 7;
544 /* If less than (allowed, supported), bump root payload */
545 if (rc_mpss > rc_mps) {
547 pcie_set_mps(parent, 128 << rc_mps);
549 /* If less than (allowed, supported), bump endpoint payload */
550 if (rc_mpss > ep_mps) {
552 pcie_set_mps(dd->pcidev, 128 << ep_mps);
556 * Now the Read Request size.
557 * No field for max supported, but PCIe spec limits it to 4096,
558 * which is code '5' (log2(4096) - 7)
561 if (max_mrrs > ((hfi1_pcie_caps >> 4) & 7))
562 max_mrrs = (hfi1_pcie_caps >> 4) & 7;
564 max_mrrs = 128 << max_mrrs;
565 rc_mrrs = pcie_get_readrq(parent);
566 ep_mrrs = pcie_get_readrq(dd->pcidev);
568 if (max_mrrs > rc_mrrs) {
570 pcie_set_readrq(parent, rc_mrrs);
572 if (max_mrrs > ep_mrrs) {
574 pcie_set_readrq(dd->pcidev, ep_mrrs);
578 /* End of PCIe capability tuning */
581 * From here through hfi1_pci_err_handler definition is invoked via
582 * PCI error infrastructure, registered via pci
584 static pci_ers_result_t
585 pci_error_detected(struct pci_dev *pdev, pci_channel_state_t state)
587 struct hfi1_devdata *dd = pci_get_drvdata(pdev);
588 pci_ers_result_t ret = PCI_ERS_RESULT_RECOVERED;
591 case pci_channel_io_normal:
592 dd_dev_info(dd, "State Normal, ignoring\n");
595 case pci_channel_io_frozen:
596 dd_dev_info(dd, "State Frozen, requesting reset\n");
597 pci_disable_device(pdev);
598 ret = PCI_ERS_RESULT_NEED_RESET;
601 case pci_channel_io_perm_failure:
603 dd_dev_info(dd, "State Permanent Failure, disabling\n");
604 /* no more register accesses! */
605 dd->flags &= ~HFI1_PRESENT;
606 hfi1_disable_after_error(dd);
608 /* else early, or other problem */
609 ret = PCI_ERS_RESULT_DISCONNECT;
612 default: /* shouldn't happen */
613 dd_dev_info(dd, "HFI1 PCI errors detected (state %d)\n",
620 static pci_ers_result_t
621 pci_mmio_enabled(struct pci_dev *pdev)
624 struct hfi1_devdata *dd = pci_get_drvdata(pdev);
625 pci_ers_result_t ret = PCI_ERS_RESULT_RECOVERED;
627 if (dd && dd->pport) {
628 words = read_port_cntr(dd->pport, C_RX_WORDS, CNTR_INVALID_VL);
630 ret = PCI_ERS_RESULT_NEED_RESET;
632 "HFI1 mmio_enabled function called, read wordscntr %llx, returning %d\n",
638 static pci_ers_result_t
639 pci_slot_reset(struct pci_dev *pdev)
641 struct hfi1_devdata *dd = pci_get_drvdata(pdev);
643 dd_dev_info(dd, "HFI1 slot_reset function called, ignored\n");
644 return PCI_ERS_RESULT_CAN_RECOVER;
648 pci_resume(struct pci_dev *pdev)
650 struct hfi1_devdata *dd = pci_get_drvdata(pdev);
652 dd_dev_info(dd, "HFI1 resume function called\n");
653 pci_cleanup_aer_uncorrect_error_status(pdev);
655 * Running jobs will fail, since it's asynchronous
656 * unlike sysfs-requested reset. Better than
659 hfi1_init(dd, 1); /* same as re-init after reset */
662 const struct pci_error_handlers hfi1_pci_err_handler = {
663 .error_detected = pci_error_detected,
664 .mmio_enabled = pci_mmio_enabled,
665 .slot_reset = pci_slot_reset,
666 .resume = pci_resume,
669 /*============================================================================*/
670 /* PCIe Gen3 support */
673 * This code is separated out because it is expected to be removed in the
674 * final shipping product. If not, then it will be revisited and items
675 * will be moved to more standard locations.
678 /* ASIC_PCI_SD_HOST_STATUS.FW_DNLD_STS field values */
679 #define DL_STATUS_HFI0 0x1 /* hfi0 firmware download complete */
680 #define DL_STATUS_HFI1 0x2 /* hfi1 firmware download complete */
681 #define DL_STATUS_BOTH 0x3 /* hfi0 and hfi1 firmware download complete */
683 /* ASIC_PCI_SD_HOST_STATUS.FW_DNLD_ERR field values */
684 #define DL_ERR_NONE 0x0 /* no error */
685 #define DL_ERR_SWAP_PARITY 0x1 /* parity error in SerDes interrupt */
686 /* or response data */
687 #define DL_ERR_DISABLED 0x2 /* hfi disabled */
688 #define DL_ERR_SECURITY 0x3 /* security check failed */
689 #define DL_ERR_SBUS 0x4 /* SBus status error */
690 #define DL_ERR_XFR_PARITY 0x5 /* parity error during ROM transfer*/
692 /* gasket block secondary bus reset delay */
693 #define SBR_DELAY_US 200000 /* 200ms */
695 static uint pcie_target = 3;
696 module_param(pcie_target, uint, S_IRUGO);
697 MODULE_PARM_DESC(pcie_target, "PCIe target speed (0 skip, 1-3 Gen1-3)");
699 static uint pcie_force;
700 module_param(pcie_force, uint, S_IRUGO);
701 MODULE_PARM_DESC(pcie_force, "Force driver to do a PCIe firmware download even if already at target speed");
703 static uint pcie_retry = 5;
704 module_param(pcie_retry, uint, S_IRUGO);
705 MODULE_PARM_DESC(pcie_retry, "Driver will try this many times to reach requested speed");
707 #define UNSET_PSET 255
708 #define DEFAULT_DISCRETE_PSET 2 /* discrete HFI */
709 #define DEFAULT_MCP_PSET 6 /* MCP HFI */
710 static uint pcie_pset = UNSET_PSET;
711 module_param(pcie_pset, uint, S_IRUGO);
712 MODULE_PARM_DESC(pcie_pset, "PCIe Eq Pset value to use, range is 0-10");
714 static uint pcie_ctle = 3; /* discrete on, integrated on */
715 module_param(pcie_ctle, uint, S_IRUGO);
716 MODULE_PARM_DESC(pcie_ctle, "PCIe static CTLE mode, bit 0 - discrete on/off, bit 1 - integrated on/off");
718 /* equalization columns */
723 /* discrete silicon preliminary equalization values */
724 static const u8 discrete_preliminary_eq[11][3] = {
726 { 0x00, 0x00, 0x12 }, /* p0 */
727 { 0x00, 0x00, 0x0c }, /* p1 */
728 { 0x00, 0x00, 0x0f }, /* p2 */
729 { 0x00, 0x00, 0x09 }, /* p3 */
730 { 0x00, 0x00, 0x00 }, /* p4 */
731 { 0x06, 0x00, 0x00 }, /* p5 */
732 { 0x09, 0x00, 0x00 }, /* p6 */
733 { 0x06, 0x00, 0x0f }, /* p7 */
734 { 0x09, 0x00, 0x09 }, /* p8 */
735 { 0x0c, 0x00, 0x00 }, /* p9 */
736 { 0x00, 0x00, 0x18 }, /* p10 */
739 /* integrated silicon preliminary equalization values */
740 static const u8 integrated_preliminary_eq[11][3] = {
742 { 0x00, 0x1e, 0x07 }, /* p0 */
743 { 0x00, 0x1e, 0x05 }, /* p1 */
744 { 0x00, 0x1e, 0x06 }, /* p2 */
745 { 0x00, 0x1e, 0x04 }, /* p3 */
746 { 0x00, 0x1e, 0x00 }, /* p4 */
747 { 0x03, 0x1e, 0x00 }, /* p5 */
748 { 0x04, 0x1e, 0x00 }, /* p6 */
749 { 0x03, 0x1e, 0x06 }, /* p7 */
750 { 0x03, 0x1e, 0x04 }, /* p8 */
751 { 0x05, 0x1e, 0x00 }, /* p9 */
752 { 0x00, 0x1e, 0x0a }, /* p10 */
755 static const u8 discrete_ctle_tunings[11][4] = {
757 { 0x48, 0x0b, 0x04, 0x04 }, /* p0 */
758 { 0x60, 0x05, 0x0f, 0x0a }, /* p1 */
759 { 0x50, 0x09, 0x06, 0x06 }, /* p2 */
760 { 0x68, 0x05, 0x0f, 0x0a }, /* p3 */
761 { 0x80, 0x05, 0x0f, 0x0a }, /* p4 */
762 { 0x70, 0x05, 0x0f, 0x0a }, /* p5 */
763 { 0x68, 0x05, 0x0f, 0x0a }, /* p6 */
764 { 0x38, 0x0f, 0x00, 0x00 }, /* p7 */
765 { 0x48, 0x09, 0x06, 0x06 }, /* p8 */
766 { 0x60, 0x05, 0x0f, 0x0a }, /* p9 */
767 { 0x38, 0x0f, 0x00, 0x00 }, /* p10 */
770 static const u8 integrated_ctle_tunings[11][4] = {
772 { 0x38, 0x0f, 0x00, 0x00 }, /* p0 */
773 { 0x38, 0x0f, 0x00, 0x00 }, /* p1 */
774 { 0x38, 0x0f, 0x00, 0x00 }, /* p2 */
775 { 0x38, 0x0f, 0x00, 0x00 }, /* p3 */
776 { 0x58, 0x0a, 0x05, 0x05 }, /* p4 */
777 { 0x48, 0x0a, 0x05, 0x05 }, /* p5 */
778 { 0x40, 0x0a, 0x05, 0x05 }, /* p6 */
779 { 0x38, 0x0f, 0x00, 0x00 }, /* p7 */
780 { 0x38, 0x0f, 0x00, 0x00 }, /* p8 */
781 { 0x38, 0x09, 0x06, 0x06 }, /* p9 */
782 { 0x38, 0x0e, 0x01, 0x01 }, /* p10 */
785 /* helper to format the value to write to hardware */
786 #define eq_value(pre, curr, post) \
788 PCIE_CFG_REG_PL102_GEN3_EQ_PRE_CURSOR_PSET_SHIFT) \
789 | (((u32)(curr)) << PCIE_CFG_REG_PL102_GEN3_EQ_CURSOR_PSET_SHIFT) \
790 | (((u32)(post)) << \
791 PCIE_CFG_REG_PL102_GEN3_EQ_POST_CURSOR_PSET_SHIFT))
794 * Load the given EQ preset table into the PCIe hardware.
796 static int load_eq_table(struct hfi1_devdata *dd, const u8 eq[11][3], u8 fs,
799 struct pci_dev *pdev = dd->pcidev;
803 u8 c_minus1, c0, c_plus1;
806 for (i = 0; i < 11; i++) {
808 pci_write_config_dword(pdev, PCIE_CFG_REG_PL103, i);
809 /* write the value */
810 c_minus1 = eq[i][PREC] / div;
811 c0 = fs - (eq[i][PREC] / div) - (eq[i][POST] / div);
812 c_plus1 = eq[i][POST] / div;
813 pci_write_config_dword(pdev, PCIE_CFG_REG_PL102,
814 eq_value(c_minus1, c0, c_plus1));
815 /* check if these coefficients violate EQ rules */
816 ret = pci_read_config_dword(dd->pcidev,
817 PCIE_CFG_REG_PL105, &violation);
819 dd_dev_err(dd, "Unable to read from PCI config\n");
825 & PCIE_CFG_REG_PL105_GEN3_EQ_VIOLATE_COEF_RULES_SMASK){
826 if (hit_error == 0) {
828 "Gen3 EQ Table Coefficient rule violations\n");
829 dd_dev_err(dd, " prec attn post\n");
831 dd_dev_err(dd, " p%02d: %02x %02x %02x\n",
832 i, (u32)eq[i][0], (u32)eq[i][1],
834 dd_dev_err(dd, " %02x %02x %02x\n",
835 (u32)c_minus1, (u32)c0, (u32)c_plus1);
845 * Steps to be done after the PCIe firmware is downloaded and
846 * before the SBR for the Pcie Gen3.
847 * The SBus resource is already being held.
849 static void pcie_post_steps(struct hfi1_devdata *dd)
853 set_sbus_fast_mode(dd);
855 * Write to the PCIe PCSes to set the G3_LOCKED_NEXT bits to 1.
856 * This avoids a spurious framing error that can otherwise be
857 * generated by the MAC layer.
859 * Use individual addresses since no broadcast is set up.
861 for (i = 0; i < NUM_PCIE_SERDES; i++) {
862 sbus_request(dd, pcie_pcs_addrs[dd->hfi1_id][i],
863 0x03, WRITE_SBUS_RECEIVER, 0x00022132);
866 clear_sbus_fast_mode(dd);
870 * Trigger a secondary bus reset (SBR) on ourselves using our parent.
872 * Based on pci_parent_bus_reset() which is not exported by the
875 static int trigger_sbr(struct hfi1_devdata *dd)
877 struct pci_dev *dev = dd->pcidev;
878 struct pci_dev *pdev;
881 if (!dev->bus->self) {
882 dd_dev_err(dd, "%s: no parent device\n", __func__);
886 /* should not be anyone else on the bus */
887 list_for_each_entry(pdev, &dev->bus->devices, bus_list)
890 "%s: another device is on the same bus\n",
896 * A secondary bus reset (SBR) issues a hot reset to our device.
897 * The following routine does a 1s wait after the reset is dropped
898 * per PCI Trhfa (recovery time). PCIe 3.0 section 6.6.1 -
899 * Conventional Reset, paragraph 3, line 35 also says that a 1s
900 * delay after a reset is required. Per spec requirements,
901 * the link is either working or not after that point.
903 return pci_reset_bus(dev);
907 * Write the given gasket interrupt register.
909 static void write_gasket_interrupt(struct hfi1_devdata *dd, int index,
912 write_csr(dd, ASIC_PCIE_SD_INTRPT_LIST + (index * 8),
913 (((u64)code << ASIC_PCIE_SD_INTRPT_LIST_INTRPT_CODE_SHIFT) |
914 ((u64)data << ASIC_PCIE_SD_INTRPT_LIST_INTRPT_DATA_SHIFT)));
918 * Tell the gasket logic how to react to the reset.
920 static void arm_gasket_logic(struct hfi1_devdata *dd)
924 reg = (((u64)1 << dd->hfi1_id) <<
925 ASIC_PCIE_SD_HOST_CMD_INTRPT_CMD_SHIFT) |
926 ((u64)pcie_serdes_broadcast[dd->hfi1_id] <<
927 ASIC_PCIE_SD_HOST_CMD_SBUS_RCVR_ADDR_SHIFT |
928 ASIC_PCIE_SD_HOST_CMD_SBR_MODE_SMASK |
929 ((u64)SBR_DELAY_US & ASIC_PCIE_SD_HOST_CMD_TIMER_MASK) <<
930 ASIC_PCIE_SD_HOST_CMD_TIMER_SHIFT);
931 write_csr(dd, ASIC_PCIE_SD_HOST_CMD, reg);
932 /* read back to push the write */
933 read_csr(dd, ASIC_PCIE_SD_HOST_CMD);
937 * CCE_PCIE_CTRL long name helpers
938 * We redefine these shorter macros to use in the code while leaving
939 * chip_registers.h to be autogenerated from the hardware spec.
941 #define LANE_BUNDLE_MASK CCE_PCIE_CTRL_PCIE_LANE_BUNDLE_MASK
942 #define LANE_BUNDLE_SHIFT CCE_PCIE_CTRL_PCIE_LANE_BUNDLE_SHIFT
943 #define LANE_DELAY_MASK CCE_PCIE_CTRL_PCIE_LANE_DELAY_MASK
944 #define LANE_DELAY_SHIFT CCE_PCIE_CTRL_PCIE_LANE_DELAY_SHIFT
945 #define MARGIN_OVERWRITE_ENABLE_SHIFT CCE_PCIE_CTRL_XMT_MARGIN_OVERWRITE_ENABLE_SHIFT
946 #define MARGIN_SHIFT CCE_PCIE_CTRL_XMT_MARGIN_SHIFT
947 #define MARGIN_G1_G2_OVERWRITE_MASK CCE_PCIE_CTRL_XMT_MARGIN_GEN1_GEN2_OVERWRITE_ENABLE_MASK
948 #define MARGIN_G1_G2_OVERWRITE_SHIFT CCE_PCIE_CTRL_XMT_MARGIN_GEN1_GEN2_OVERWRITE_ENABLE_SHIFT
949 #define MARGIN_GEN1_GEN2_MASK CCE_PCIE_CTRL_XMT_MARGIN_GEN1_GEN2_MASK
950 #define MARGIN_GEN1_GEN2_SHIFT CCE_PCIE_CTRL_XMT_MARGIN_GEN1_GEN2_SHIFT
953 * Write xmt_margin for full-swing (WFR-B) or half-swing (WFR-C).
955 static void write_xmt_margin(struct hfi1_devdata *dd, const char *fname)
963 pcie_ctrl = read_csr(dd, CCE_PCIE_CTRL);
966 * For Discrete, use full-swing.
967 * - PCIe TX defaults to full-swing.
968 * Leave this register as default.
969 * For Integrated, use half-swing
970 * - Copy xmt_margin and xmt_margin_oe
971 * from Gen1/Gen2 to Gen3.
973 if (dd->pcidev->device == PCI_DEVICE_ID_INTEL1) { /* integrated */
974 /* extract initial fields */
975 xmt_margin = (pcie_ctrl >> MARGIN_GEN1_GEN2_SHIFT)
976 & MARGIN_GEN1_GEN2_MASK;
977 xmt_margin_oe = (pcie_ctrl >> MARGIN_G1_G2_OVERWRITE_SHIFT)
978 & MARGIN_G1_G2_OVERWRITE_MASK;
979 lane_delay = (pcie_ctrl >> LANE_DELAY_SHIFT) & LANE_DELAY_MASK;
980 lane_bundle = (pcie_ctrl >> LANE_BUNDLE_SHIFT)
984 * For A0, EFUSE values are not set. Override with the
989 * xmt_margin and OverwiteEnabel should be the
990 * same for Gen1/Gen2 and Gen3
994 lane_delay = 0xF; /* Delay 240ns. */
995 lane_bundle = 0x0; /* Set to 1 lane. */
998 /* overwrite existing values */
999 pcie_ctrl = (xmt_margin << MARGIN_GEN1_GEN2_SHIFT)
1000 | (xmt_margin_oe << MARGIN_G1_G2_OVERWRITE_SHIFT)
1001 | (xmt_margin << MARGIN_SHIFT)
1002 | (xmt_margin_oe << MARGIN_OVERWRITE_ENABLE_SHIFT)
1003 | (lane_delay << LANE_DELAY_SHIFT)
1004 | (lane_bundle << LANE_BUNDLE_SHIFT);
1006 write_csr(dd, CCE_PCIE_CTRL, pcie_ctrl);
1009 dd_dev_dbg(dd, "%s: program XMT margin, CcePcieCtrl 0x%llx\n",
1014 * Do all the steps needed to transition the PCIe link to Gen3 speed.
1016 int do_pcie_gen3_transition(struct hfi1_devdata *dd)
1018 struct pci_dev *parent = dd->pcidev->bus->self;
1024 int do_retry, retry_count = 0;
1027 uint pset = pcie_pset;
1028 u16 target_vector, target_speed;
1029 u16 lnkctl2, vendor;
1032 const u8 (*ctle_tunings)[4];
1033 uint static_ctle_mode;
1034 int return_error = 0;
1036 /* PCIe Gen3 is for the ASIC only */
1037 if (dd->icode != ICODE_RTL_SILICON)
1040 if (pcie_target == 1) { /* target Gen1 */
1041 target_vector = PCI_EXP_LNKCTL2_TLS_2_5GT;
1042 target_speed = 2500;
1043 } else if (pcie_target == 2) { /* target Gen2 */
1044 target_vector = PCI_EXP_LNKCTL2_TLS_5_0GT;
1045 target_speed = 5000;
1046 } else if (pcie_target == 3) { /* target Gen3 */
1047 target_vector = PCI_EXP_LNKCTL2_TLS_8_0GT;
1048 target_speed = 8000;
1050 /* off or invalid target - skip */
1051 dd_dev_info(dd, "%s: Skipping PCIe transition\n", __func__);
1055 /* if already at target speed, done (unless forced) */
1056 if (dd->lbus_speed == target_speed) {
1057 dd_dev_info(dd, "%s: PCIe already at gen%d, %s\n", __func__,
1059 pcie_force ? "re-doing anyway" : "skipping");
1065 * The driver cannot do the transition if it has no access to the
1066 * upstream component
1069 dd_dev_info(dd, "%s: No upstream, Can't do gen3 transition\n",
1075 * Do the Gen3 transition. Steps are those of the PCIe Gen3
1079 /* step 1: pcie link working in gen1/gen2 */
1081 /* step 2: if either side is not capable of Gen3, done */
1082 if (pcie_target == 3 && !dd->link_gen3_capable) {
1083 dd_dev_err(dd, "The PCIe link is not Gen3 capable\n");
1088 /* hold the SBus resource across the firmware download and SBR */
1089 ret = acquire_chip_resource(dd, CR_SBUS, SBUS_TIMEOUT);
1091 dd_dev_err(dd, "%s: unable to acquire SBus resource\n",
1096 /* make sure thermal polling is not causing interrupts */
1097 therm = read_csr(dd, ASIC_CFG_THERM_POLL_EN);
1099 write_csr(dd, ASIC_CFG_THERM_POLL_EN, 0x0);
1101 dd_dev_info(dd, "%s: Disabled therm polling\n",
1106 /* the SBus download will reset the spico for thermal */
1108 /* step 3: download SBus Master firmware */
1109 /* step 4: download PCIe Gen3 SerDes firmware */
1110 dd_dev_info(dd, "%s: downloading firmware\n", __func__);
1111 ret = load_pcie_firmware(dd);
1113 /* do not proceed if the firmware cannot be downloaded */
1118 /* step 5: set up device parameter settings */
1119 dd_dev_info(dd, "%s: setting PCIe registers\n", __func__);
1122 * PcieCfgSpcie1 - Link Control 3
1123 * Leave at reset value. No need to set PerfEq - link equalization
1124 * will be performed automatically after the SBR when the target
1128 /* clear all 16 per-lane error bits (PCIe: Lane Error Status) */
1129 pci_write_config_dword(dd->pcidev, PCIE_CFG_SPCIE2, 0xffff);
1131 /* step 5a: Set Synopsys Port Logic registers */
1134 * PcieCfgRegPl2 - Port Force Link
1136 * Set the low power field to 0x10 to avoid unnecessary power
1137 * management messages. All other fields are zero.
1139 reg32 = 0x10ul << PCIE_CFG_REG_PL2_LOW_PWR_ENT_CNT_SHIFT;
1140 pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL2, reg32);
1143 * PcieCfgRegPl100 - Gen3 Control
1145 * turn off PcieCfgRegPl100.Gen3ZRxDcNonCompl
1146 * turn on PcieCfgRegPl100.EqEieosCnt
1147 * Everything else zero.
1149 reg32 = PCIE_CFG_REG_PL100_EQ_EIEOS_CNT_SMASK;
1150 pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL100, reg32);
1153 * PcieCfgRegPl101 - Gen3 EQ FS and LF
1154 * PcieCfgRegPl102 - Gen3 EQ Presets to Coefficients Mapping
1155 * PcieCfgRegPl103 - Gen3 EQ Preset Index
1156 * PcieCfgRegPl105 - Gen3 EQ Status
1158 * Give initial EQ settings.
1160 if (dd->pcidev->device == PCI_DEVICE_ID_INTEL0) { /* discrete */
1161 /* 1000mV, FS=24, LF = 8 */
1165 eq = discrete_preliminary_eq;
1166 default_pset = DEFAULT_DISCRETE_PSET;
1167 ctle_tunings = discrete_ctle_tunings;
1168 /* bit 0 - discrete on/off */
1169 static_ctle_mode = pcie_ctle & 0x1;
1171 /* 400mV, FS=29, LF = 9 */
1175 eq = integrated_preliminary_eq;
1176 default_pset = DEFAULT_MCP_PSET;
1177 ctle_tunings = integrated_ctle_tunings;
1178 /* bit 1 - integrated on/off */
1179 static_ctle_mode = (pcie_ctle >> 1) & 0x1;
1181 pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL101,
1183 PCIE_CFG_REG_PL101_GEN3_EQ_LOCAL_FS_SHIFT) |
1185 PCIE_CFG_REG_PL101_GEN3_EQ_LOCAL_LF_SHIFT));
1186 ret = load_eq_table(dd, eq, fs, div);
1191 * PcieCfgRegPl106 - Gen3 EQ Control
1193 * Set Gen3EqPsetReqVec, leave other fields 0.
1195 if (pset == UNSET_PSET)
1196 pset = default_pset;
1197 if (pset > 10) { /* valid range is 0-10, inclusive */
1198 dd_dev_err(dd, "%s: Invalid Eq Pset %u, setting to %d\n",
1199 __func__, pset, default_pset);
1200 pset = default_pset;
1202 dd_dev_info(dd, "%s: using EQ Pset %u\n", __func__, pset);
1203 pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL106,
1205 PCIE_CFG_REG_PL106_GEN3_EQ_PSET_REQ_VEC_SHIFT) |
1206 PCIE_CFG_REG_PL106_GEN3_EQ_EVAL2MS_DISABLE_SMASK |
1207 PCIE_CFG_REG_PL106_GEN3_EQ_PHASE23_EXIT_MODE_SMASK);
1210 * step 5b: Do post firmware download steps via SBus
1212 dd_dev_info(dd, "%s: doing pcie post steps\n", __func__);
1213 pcie_post_steps(dd);
1216 * step 5c: Program gasket interrupts
1218 /* set the Rx Bit Rate to REFCLK ratio */
1219 write_gasket_interrupt(dd, intnum++, 0x0006, 0x0050);
1220 /* disable pCal for PCIe Gen3 RX equalization */
1221 /* select adaptive or static CTLE */
1222 write_gasket_interrupt(dd, intnum++, 0x0026,
1223 0x5b01 | (static_ctle_mode << 3));
1225 * Enable iCal for PCIe Gen3 RX equalization, and set which
1226 * evaluation of RX_EQ_EVAL will launch the iCal procedure.
1228 write_gasket_interrupt(dd, intnum++, 0x0026, 0x5202);
1230 if (static_ctle_mode) {
1231 /* apply static CTLE tunings */
1232 u8 pcie_dc, pcie_lf, pcie_hf, pcie_bw;
1234 pcie_dc = ctle_tunings[pset][0];
1235 pcie_lf = ctle_tunings[pset][1];
1236 pcie_hf = ctle_tunings[pset][2];
1237 pcie_bw = ctle_tunings[pset][3];
1238 write_gasket_interrupt(dd, intnum++, 0x0026, 0x0200 | pcie_dc);
1239 write_gasket_interrupt(dd, intnum++, 0x0026, 0x0100 | pcie_lf);
1240 write_gasket_interrupt(dd, intnum++, 0x0026, 0x0000 | pcie_hf);
1241 write_gasket_interrupt(dd, intnum++, 0x0026, 0x5500 | pcie_bw);
1244 /* terminate list */
1245 write_gasket_interrupt(dd, intnum++, 0x0000, 0x0000);
1248 * step 5d: program XMT margin
1250 write_xmt_margin(dd, __func__);
1253 * step 5e: disable active state power management (ASPM). It
1254 * will be enabled if required later
1256 dd_dev_info(dd, "%s: clearing ASPM\n", __func__);
1257 aspm_hw_disable_l1(dd);
1260 * step 5f: clear DirectSpeedChange
1261 * PcieCfgRegPl67.DirectSpeedChange must be zero to prevent the
1262 * change in the speed target from starting before we are ready.
1263 * This field defaults to 0 and we are not changing it, so nothing
1267 /* step 5g: Set target link speed */
1269 * Set target link speed to be target on both device and parent.
1270 * On setting the parent: Some system BIOSs "helpfully" set the
1271 * parent target speed to Gen2 to match the ASIC's initial speed.
1272 * We can set the target Gen3 because we have already checked
1273 * that it is Gen3 capable earlier.
1275 dd_dev_info(dd, "%s: setting parent target link speed\n", __func__);
1276 ret = pcie_capability_read_word(parent, PCI_EXP_LNKCTL2, &lnkctl2);
1278 dd_dev_err(dd, "Unable to read from PCI config\n");
1283 dd_dev_info(dd, "%s: ..old link control2: 0x%x\n", __func__,
1285 /* only write to parent if target is not as high as ours */
1286 if ((lnkctl2 & PCI_EXP_LNKCTL2_TLS) < target_vector) {
1287 lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS;
1288 lnkctl2 |= target_vector;
1289 dd_dev_info(dd, "%s: ..new link control2: 0x%x\n", __func__,
1291 ret = pcie_capability_write_word(parent,
1292 PCI_EXP_LNKCTL2, lnkctl2);
1294 dd_dev_err(dd, "Unable to write to PCI config\n");
1299 dd_dev_info(dd, "%s: ..target speed is OK\n", __func__);
1302 dd_dev_info(dd, "%s: setting target link speed\n", __func__);
1303 ret = pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKCTL2, &lnkctl2);
1305 dd_dev_err(dd, "Unable to read from PCI config\n");
1310 dd_dev_info(dd, "%s: ..old link control2: 0x%x\n", __func__,
1312 lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS;
1313 lnkctl2 |= target_vector;
1314 dd_dev_info(dd, "%s: ..new link control2: 0x%x\n", __func__,
1316 ret = pcie_capability_write_word(dd->pcidev, PCI_EXP_LNKCTL2, lnkctl2);
1318 dd_dev_err(dd, "Unable to write to PCI config\n");
1323 /* step 5h: arm gasket logic */
1324 /* hold DC in reset across the SBR */
1325 write_csr(dd, CCE_DC_CTRL, CCE_DC_CTRL_DC_RESET_SMASK);
1326 (void)read_csr(dd, CCE_DC_CTRL); /* DC reset hold */
1327 /* save firmware control across the SBR */
1328 fw_ctrl = read_csr(dd, MISC_CFG_FW_CTRL);
1330 dd_dev_info(dd, "%s: arming gasket logic\n", __func__);
1331 arm_gasket_logic(dd);
1334 * step 6: quiesce PCIe link
1335 * The chip has already been reset, so there will be no traffic
1336 * from the chip. Linux has no easy way to enforce that it will
1337 * not try to access the device, so we just need to hope it doesn't
1338 * do it while we are doing the reset.
1342 * step 7: initiate the secondary bus reset (SBR)
1343 * step 8: hardware brings the links back up
1344 * step 9: wait for link speed transition to be complete
1346 dd_dev_info(dd, "%s: calling trigger_sbr\n", __func__);
1347 ret = trigger_sbr(dd);
1351 /* step 10: decide what to do next */
1353 /* check if we can read PCI space */
1354 ret = pci_read_config_word(dd->pcidev, PCI_VENDOR_ID, &vendor);
1357 "%s: read of VendorID failed after SBR, err %d\n",
1362 if (vendor == 0xffff) {
1363 dd_dev_info(dd, "%s: VendorID is all 1s after SBR\n", __func__);
1369 /* restore PCI space registers we know were reset */
1370 dd_dev_info(dd, "%s: calling restore_pci_variables\n", __func__);
1371 ret = restore_pci_variables(dd);
1373 dd_dev_err(dd, "%s: Could not restore PCI variables\n",
1379 /* restore firmware control */
1380 write_csr(dd, MISC_CFG_FW_CTRL, fw_ctrl);
1383 * Check the gasket block status.
1385 * This is the first CSR read after the SBR. If the read returns
1386 * all 1s (fails), the link did not make it back.
1388 * Once we're sure we can read and write, clear the DC reset after
1389 * the SBR. Then check for any per-lane errors. Then look over
1392 reg = read_csr(dd, ASIC_PCIE_SD_HOST_STATUS);
1393 dd_dev_info(dd, "%s: gasket block status: 0x%llx\n", __func__, reg);
1394 if (reg == ~0ull) { /* PCIe read failed/timeout */
1395 dd_dev_err(dd, "SBR failed - unable to read from device\n");
1401 /* clear the DC reset */
1402 write_csr(dd, CCE_DC_CTRL, 0);
1404 /* Set the LED off */
1407 /* check for any per-lane errors */
1408 ret = pci_read_config_dword(dd->pcidev, PCIE_CFG_SPCIE2, ®32);
1410 dd_dev_err(dd, "Unable to read from PCI config\n");
1415 dd_dev_info(dd, "%s: per-lane errors: 0x%x\n", __func__, reg32);
1417 /* extract status, look for our HFI */
1418 status = (reg >> ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_STS_SHIFT)
1419 & ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_STS_MASK;
1420 if ((status & (1 << dd->hfi1_id)) == 0) {
1422 "%s: gasket status 0x%x, expecting 0x%x\n",
1423 __func__, status, 1 << dd->hfi1_id);
1429 err = (reg >> ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_ERR_SHIFT)
1430 & ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_ERR_MASK;
1432 dd_dev_err(dd, "%s: gasket error %d\n", __func__, err);
1437 /* update our link information cache */
1438 update_lbus_info(dd);
1439 dd_dev_info(dd, "%s: new speed and width: %s\n", __func__,
1442 if (dd->lbus_speed != target_speed) { /* not target */
1444 do_retry = retry_count < pcie_retry;
1445 dd_dev_err(dd, "PCIe link speed did not switch to Gen%d%s\n",
1446 pcie_target, do_retry ? ", retrying" : "");
1449 msleep(100); /* allow time to settle */
1457 write_csr(dd, ASIC_CFG_THERM_POLL_EN, 0x1);
1459 dd_dev_info(dd, "%s: Re-enable therm polling\n",
1462 release_chip_resource(dd, CR_SBUS);
1464 /* return no error if it is OK to be at current speed */
1465 if (ret && !return_error) {
1466 dd_dev_err(dd, "Proceeding at current speed PCIe speed\n");
1470 dd_dev_info(dd, "%s: done\n", __func__);