1 # SPDX-License-Identifier: GPL-2.0
4 bool "64-bit kernel" if "$(ARCH)" = "x86"
5 default "$(ARCH)" != "i386"
7 Say yes to build a 64-bit kernel - formerly known as x86_64
8 Say no to build a 32-bit kernel - formerly known as i386
13 # Options that are inherently 32-bit kernel only:
14 select ARCH_WANT_IPC_PARSE_VERSION
16 select CLONE_BACKWARDS
18 select HAVE_GENERIC_DMA_COHERENT
19 select MODULES_USE_ELF_REL
25 # Options that are inherently 64-bit kernel only:
26 select ARCH_HAS_GIGANTIC_PAGE if (MEMORY_ISOLATION && COMPACTION) || CMA
27 select ARCH_SUPPORTS_INT128
28 select ARCH_USE_CMPXCHG_LOCKREF
29 select HAVE_ARCH_SOFT_DIRTY
30 select MODULES_USE_ELF_RELA
31 select NEED_DMA_MAP_STATE
33 select X86_DEV_DMA_OPS
34 select ARCH_HAS_SYSCALL_WRAPPER
39 # ( Note that options that are marked 'if X86_64' could in principle be
40 # ported to 32-bit as well. )
45 # Note: keep this list sorted alphabetically
47 select ACPI_LEGACY_TABLES_LOOKUP if ACPI
48 select ACPI_SYSTEM_POWER_STATES_SUPPORT if ACPI
50 select ARCH_CLOCKSOURCE_DATA
51 select ARCH_DISCARD_MEMBLOCK
52 select ARCH_HAS_ACPI_TABLE_UPGRADE if ACPI
53 select ARCH_HAS_DEBUG_VIRTUAL
54 select ARCH_HAS_DEVMEM_IS_ALLOWED
55 select ARCH_HAS_ELF_RANDOMIZE
56 select ARCH_HAS_FAST_MULTIPLIER
57 select ARCH_HAS_FILTER_PGPROT
58 select ARCH_HAS_FORTIFY_SOURCE
59 select ARCH_HAS_GCOV_PROFILE_ALL
60 select ARCH_HAS_KCOV if X86_64
61 select ARCH_HAS_MEMBARRIER_SYNC_CORE
62 select ARCH_HAS_PMEM_API if X86_64
63 select ARCH_HAS_PTE_SPECIAL
64 select ARCH_HAS_REFCOUNT
65 select ARCH_HAS_UACCESS_FLUSHCACHE if X86_64
66 select ARCH_HAS_UACCESS_MCSAFE if X86_64
67 select ARCH_HAS_SET_MEMORY
68 select ARCH_HAS_SG_CHAIN
69 select ARCH_HAS_STRICT_KERNEL_RWX
70 select ARCH_HAS_STRICT_MODULE_RWX
71 select ARCH_HAS_SYNC_CORE_BEFORE_USERMODE
72 select ARCH_HAS_UBSAN_SANITIZE_ALL
73 select ARCH_HAS_ZONE_DEVICE if X86_64
74 select ARCH_HAVE_NMI_SAFE_CMPXCHG
75 select ARCH_MIGHT_HAVE_ACPI_PDC if ACPI
76 select ARCH_MIGHT_HAVE_PC_PARPORT
77 select ARCH_MIGHT_HAVE_PC_SERIO
78 select ARCH_SUPPORTS_ATOMIC_RMW
79 select ARCH_SUPPORTS_NUMA_BALANCING if X86_64
80 select ARCH_USE_BUILTIN_BSWAP
81 select ARCH_USE_QUEUED_RWLOCKS
82 select ARCH_USE_QUEUED_SPINLOCKS
83 select ARCH_WANT_BATCHED_UNMAP_TLB_FLUSH
84 select ARCH_WANTS_DYNAMIC_TASK_STRUCT
85 select ARCH_WANTS_THP_SWAP if X86_64
86 select BUILDTIME_EXTABLE_SORT
88 select CLOCKSOURCE_VALIDATE_LAST_CYCLE
89 select CLOCKSOURCE_WATCHDOG
90 select DCACHE_WORD_ACCESS
92 select EDAC_ATOMIC_SCRUB
94 select GENERIC_CLOCKEVENTS
95 select GENERIC_CLOCKEVENTS_BROADCAST if X86_64 || (X86_32 && X86_LOCAL_APIC)
96 select GENERIC_CLOCKEVENTS_MIN_ADJUST
97 select GENERIC_CMOS_UPDATE
98 select GENERIC_CPU_AUTOPROBE
99 select GENERIC_CPU_VULNERABILITIES
100 select GENERIC_EARLY_IOREMAP
101 select GENERIC_FIND_FIRST_BIT
103 select GENERIC_IRQ_EFFECTIVE_AFF_MASK if SMP
104 select GENERIC_IRQ_MATRIX_ALLOCATOR if X86_LOCAL_APIC
105 select GENERIC_IRQ_MIGRATION if SMP
106 select GENERIC_IRQ_PROBE
107 select GENERIC_IRQ_RESERVATION_MODE
108 select GENERIC_IRQ_SHOW
109 select GENERIC_PENDING_IRQ if SMP
110 select GENERIC_SMP_IDLE_THREAD
111 select GENERIC_STRNCPY_FROM_USER
112 select GENERIC_STRNLEN_USER
113 select GENERIC_TIME_VSYSCALL
114 select HARDLOCKUP_CHECK_TIMESTAMP if X86_64
115 select HAVE_ACPI_APEI if ACPI
116 select HAVE_ACPI_APEI_NMI if ACPI
117 select HAVE_ALIGNED_STRUCT_PAGE if SLUB
118 select HAVE_ARCH_AUDITSYSCALL
119 select HAVE_ARCH_HUGE_VMAP if X86_64 || X86_PAE
120 select HAVE_ARCH_JUMP_LABEL
121 select HAVE_ARCH_KASAN if X86_64
122 select HAVE_ARCH_KGDB
123 select HAVE_ARCH_MMAP_RND_BITS if MMU
124 select HAVE_ARCH_MMAP_RND_COMPAT_BITS if MMU && COMPAT
125 select HAVE_ARCH_COMPAT_MMAP_BASES if MMU && COMPAT
126 select HAVE_ARCH_SECCOMP_FILTER
127 select HAVE_ARCH_THREAD_STRUCT_WHITELIST
128 select HAVE_ARCH_TRACEHOOK
129 select HAVE_ARCH_TRANSPARENT_HUGEPAGE
130 select HAVE_ARCH_TRANSPARENT_HUGEPAGE_PUD if X86_64
131 select HAVE_ARCH_VMAP_STACK if X86_64
132 select HAVE_ARCH_WITHIN_STACK_FRAMES
133 select HAVE_CMPXCHG_DOUBLE
134 select HAVE_CMPXCHG_LOCAL
135 select HAVE_CONTEXT_TRACKING if X86_64
136 select HAVE_COPY_THREAD_TLS
137 select HAVE_C_RECORDMCOUNT
138 select HAVE_DEBUG_KMEMLEAK
139 select HAVE_DEBUG_STACKOVERFLOW
140 select HAVE_DMA_CONTIGUOUS
141 select HAVE_DYNAMIC_FTRACE
142 select HAVE_DYNAMIC_FTRACE_WITH_REGS
144 select HAVE_EFFICIENT_UNALIGNED_ACCESS
145 select HAVE_EXIT_THREAD
146 select HAVE_FENTRY if X86_64 || DYNAMIC_FTRACE
147 select HAVE_FTRACE_MCOUNT_RECORD
148 select HAVE_FUNCTION_GRAPH_TRACER
149 select HAVE_FUNCTION_TRACER
150 select HAVE_GCC_PLUGINS
151 select HAVE_HW_BREAKPOINT
153 select HAVE_IOREMAP_PROT
154 select HAVE_IRQ_EXIT_ON_IRQ_STACK if X86_64
155 select HAVE_IRQ_TIME_ACCOUNTING
156 select HAVE_KERNEL_BZIP2
157 select HAVE_KERNEL_GZIP
158 select HAVE_KERNEL_LZ4
159 select HAVE_KERNEL_LZMA
160 select HAVE_KERNEL_LZO
161 select HAVE_KERNEL_XZ
163 select HAVE_KPROBES_ON_FTRACE
164 select HAVE_FUNCTION_ERROR_INJECTION
165 select HAVE_KRETPROBES
167 select HAVE_LIVEPATCH if X86_64
169 select HAVE_MEMBLOCK_NODE_MAP
170 select HAVE_MIXED_BREAKPOINTS_REGS
171 select HAVE_MOD_ARCH_SPECIFIC
174 select HAVE_OPTPROBES
175 select HAVE_PCSPKR_PLATFORM
176 select HAVE_PERF_EVENTS
177 select HAVE_PERF_EVENTS_NMI
178 select HAVE_HARDLOCKUP_DETECTOR_PERF if PERF_EVENTS && HAVE_PERF_EVENTS_NMI
179 select HAVE_PERF_REGS
180 select HAVE_PERF_USER_STACK_DUMP
181 select HAVE_RCU_TABLE_FREE
182 select HAVE_REGS_AND_STACK_ACCESS_API
183 select HAVE_RELIABLE_STACKTRACE if X86_64 && UNWINDER_FRAME_POINTER && STACK_VALIDATION
184 select HAVE_STACKPROTECTOR if CC_HAS_SANE_STACKPROTECTOR
185 select HAVE_STACK_VALIDATION if X86_64
187 select HAVE_SYSCALL_TRACEPOINTS
188 select HAVE_UNSTABLE_SCHED_CLOCK
189 select HAVE_USER_RETURN_NOTIFIER
190 select IRQ_FORCED_THREADING
191 select NEED_SG_DMA_LENGTH
192 select PCI_LOCKLESS_CONFIG
195 select RTC_MC146818_LIB
198 select SYSCTL_EXCEPTION_TRACE
199 select THREAD_INFO_IN_TASK
200 select USER_STACKTRACE_SUPPORT
202 select X86_FEATURE_NAMES if PROC_FS
204 config INSTRUCTION_DECODER
206 depends on KPROBES || PERF_EVENTS || UPROBES
210 default "elf32-i386" if X86_32
211 default "elf64-x86-64" if X86_64
213 config ARCH_DEFCONFIG
215 default "arch/x86/configs/i386_defconfig" if X86_32
216 default "arch/x86/configs/x86_64_defconfig" if X86_64
218 config LOCKDEP_SUPPORT
221 config STACKTRACE_SUPPORT
227 config ARCH_MMAP_RND_BITS_MIN
231 config ARCH_MMAP_RND_BITS_MAX
235 config ARCH_MMAP_RND_COMPAT_BITS_MIN
238 config ARCH_MMAP_RND_COMPAT_BITS_MAX
244 config GENERIC_ISA_DMA
246 depends on ISA_DMA_API
251 select GENERIC_BUG_RELATIVE_POINTERS if X86_64
253 config GENERIC_BUG_RELATIVE_POINTERS
256 config GENERIC_HWEIGHT
259 config ARCH_MAY_HAVE_PC_FDC
261 depends on ISA_DMA_API
263 config RWSEM_XCHGADD_ALGORITHM
266 config GENERIC_CALIBRATE_DELAY
269 config ARCH_HAS_CPU_RELAX
272 config ARCH_HAS_CACHE_LINE_SIZE
275 config ARCH_HAS_FILTER_PGPROT
278 config HAVE_SETUP_PER_CPU_AREA
281 config NEED_PER_CPU_EMBED_FIRST_CHUNK
284 config NEED_PER_CPU_PAGE_FIRST_CHUNK
287 config ARCH_HIBERNATION_POSSIBLE
290 config ARCH_SUSPEND_POSSIBLE
293 config ARCH_WANT_HUGE_PMD_SHARE
296 config ARCH_WANT_GENERAL_HUGETLB
305 config ARCH_SUPPORTS_OPTIMIZED_INLINING
308 config ARCH_SUPPORTS_DEBUG_PAGEALLOC
311 config KASAN_SHADOW_OFFSET
314 default 0xdffffc0000000000
316 config HAVE_INTEL_TXT
318 depends on INTEL_IOMMU && ACPI
322 depends on X86_32 && SMP
326 depends on X86_64 && SMP
328 config X86_32_LAZY_GS
330 depends on X86_32 && !STACKPROTECTOR
332 config ARCH_SUPPORTS_UPROBES
335 config FIX_EARLYCON_MEM
338 config DYNAMIC_PHYSICAL_MASK
341 config PGTABLE_LEVELS
343 default 5 if X86_5LEVEL
348 source "init/Kconfig"
350 config CC_HAS_SANE_STACKPROTECTOR
352 default $(success,$(srctree)/scripts/gcc-x86_64-has-stack-protector.sh $(CC)) if 64BIT
353 default $(success,$(srctree)/scripts/gcc-x86_32-has-stack-protector.sh $(CC))
355 We have to make sure stack protector is unconditionally disabled if
356 the compiler produces broken code.
358 source "kernel/Kconfig.freezer"
360 menu "Processor type and features"
363 bool "DMA memory allocation support" if EXPERT
366 DMA memory allocation support allows devices with less than 32-bit
367 addressing to allocate within the first 16MB of address space.
368 Disable if no such devices will be used.
373 bool "Symmetric multi-processing support"
375 This enables support for systems with more than one CPU. If you have
376 a system with only one CPU, say N. If you have a system with more
379 If you say N here, the kernel will run on uni- and multiprocessor
380 machines, but will use only one CPU of a multiprocessor machine. If
381 you say Y here, the kernel will run on many, but not all,
382 uniprocessor machines. On a uniprocessor machine, the kernel
383 will run faster if you say N here.
385 Note that if you say Y here and choose architecture "586" or
386 "Pentium" under "Processor family", the kernel will not work on 486
387 architectures. Similarly, multiprocessor kernels for the "PPro"
388 architecture may not work on all Pentium based boards.
390 People using multiprocessor machines who say Y here should also say
391 Y to "Enhanced Real Time Clock Support", below. The "Advanced Power
392 Management" code will be disabled if you say Y here.
394 See also <file:Documentation/x86/i386/IO-APIC.txt>,
395 <file:Documentation/lockup-watchdogs.txt> and the SMP-HOWTO available at
396 <http://www.tldp.org/docs.html#howto>.
398 If you don't know what to do here, say N.
400 config X86_FEATURE_NAMES
401 bool "Processor feature human-readable names" if EMBEDDED
404 This option compiles in a table of x86 feature bits and corresponding
405 names. This is required to support /proc/cpuinfo and a few kernel
406 messages. You can disable this to save space, at the expense of
407 making those few kernel messages show numeric feature bits instead.
412 bool "Support x2apic"
413 depends on X86_LOCAL_APIC && X86_64 && (IRQ_REMAP || HYPERVISOR_GUEST)
415 This enables x2apic support on CPUs that have this feature.
417 This allows 32-bit apic IDs (so it can support very large systems),
418 and accesses the local apic via MSRs not via mmio.
420 If you don't know what to do here, say N.
423 bool "Enable MPS table" if ACPI || SFI
425 depends on X86_LOCAL_APIC
427 For old smp systems that do not have proper acpi support. Newer systems
428 (esp with 64bit cpus) with acpi support, MADT and DSDT will override it
432 depends on X86_GOLDFISH
435 bool "Avoid speculative indirect branches in kernel"
437 select STACK_VALIDATION if HAVE_STACK_VALIDATION
439 Compile kernel with the retpoline compiler options to guard against
440 kernel-to-user data leaks by avoiding speculative indirect
441 branches. Requires a compiler with -mindirect-branch=thunk-extern
442 support for full protection. The kernel may run slower.
444 Without compiler support, at least indirect branches in assembler
445 code are eliminated. Since this includes the syscall entry path,
446 it is not entirely pointless.
449 bool "Intel Resource Director Technology support"
451 depends on X86 && CPU_SUP_INTEL
454 Select to enable resource allocation and monitoring which are
455 sub-features of Intel Resource Director Technology(RDT). More
456 information about RDT can be found in the Intel x86
457 Architecture Software Developer Manual.
463 bool "Support for big SMP systems with more than 8 CPUs"
466 This option is needed for the systems that have more than 8 CPUs
468 config X86_EXTENDED_PLATFORM
469 bool "Support for extended (non-PC) x86 platforms"
472 If you disable this option then the kernel will only support
473 standard PC platforms. (which covers the vast majority of
476 If you enable this option then you'll be able to select support
477 for the following (non-PC) 32 bit x86 platforms:
478 Goldfish (Android emulator)
481 SGI 320/540 (Visual Workstation)
482 STA2X11-based (e.g. Northville)
483 Moorestown MID devices
485 If you have one of these systems, or if you want to build a
486 generic distribution kernel, say Y here - otherwise say N.
490 config X86_EXTENDED_PLATFORM
491 bool "Support for extended (non-PC) x86 platforms"
494 If you disable this option then the kernel will only support
495 standard PC platforms. (which covers the vast majority of
498 If you enable this option then you'll be able to select support
499 for the following (non-PC) 64 bit x86 platforms:
504 If you have one of these systems, or if you want to build a
505 generic distribution kernel, say Y here - otherwise say N.
507 # This is an alphabetically sorted list of 64 bit extended platforms
508 # Please maintain the alphabetic order if and when there are additions
510 bool "Numascale NumaChip"
512 depends on X86_EXTENDED_PLATFORM
515 depends on X86_X2APIC
516 depends on PCI_MMCONFIG
518 Adds support for Numascale NumaChip large-SMP systems. Needed to
519 enable more than ~168 cores.
520 If you don't have one of these, you should say N here.
524 select HYPERVISOR_GUEST
526 depends on X86_64 && PCI
527 depends on X86_EXTENDED_PLATFORM
530 Support for ScaleMP vSMP systems. Say 'Y' here if this kernel is
531 supposed to run on these EM64T-based machines. Only choose this option
532 if you have one of these machines.
535 bool "SGI Ultraviolet"
537 depends on X86_EXTENDED_PLATFORM
540 depends on X86_X2APIC
543 This option is needed in order to support SGI Ultraviolet systems.
544 If you don't have one of these, you should say N here.
546 # Following is an alphabetically sorted list of 32 bit extended platforms
547 # Please maintain the alphabetic order if and when there are additions
550 bool "Goldfish (Virtual Platform)"
551 depends on X86_EXTENDED_PLATFORM
553 Enable support for the Goldfish virtual platform used primarily
554 for Android development. Unless you are building for the Android
555 Goldfish emulator say N here.
558 bool "CE4100 TV platform"
560 depends on PCI_GODIRECT
561 depends on X86_IO_APIC
563 depends on X86_EXTENDED_PLATFORM
564 select X86_REBOOTFIXUPS
566 select OF_EARLY_FLATTREE
568 Select for the Intel CE media processor (CE4100) SOC.
569 This option compiles in support for the CE4100 SOC for settop
570 boxes and media devices.
573 bool "Intel MID platform support"
574 depends on X86_EXTENDED_PLATFORM
575 depends on X86_PLATFORM_DEVICES
577 depends on X86_64 || (PCI_GOANY && X86_32)
578 depends on X86_IO_APIC
584 select MFD_INTEL_MSIC
586 Select to build a kernel capable of supporting Intel MID (Mobile
587 Internet Device) platform systems which do not have the PCI legacy
588 interfaces. If you are building for a PC class system say N here.
590 Intel MID platforms are based on an Intel processor and chipset which
591 consume less power than most of the x86 derivatives.
593 config X86_INTEL_QUARK
594 bool "Intel Quark platform support"
596 depends on X86_EXTENDED_PLATFORM
597 depends on X86_PLATFORM_DEVICES
601 depends on X86_IO_APIC
606 Select to include support for Quark X1000 SoC.
607 Say Y here if you have a Quark based system such as the Arduino
608 compatible Intel Galileo.
610 config X86_INTEL_LPSS
611 bool "Intel Low Power Subsystem Support"
612 depends on X86 && ACPI
617 Select to build support for Intel Low Power Subsystem such as
618 found on Intel Lynxpoint PCH. Selecting this option enables
619 things like clock tree (common clock framework) and pincontrol
620 which are needed by the LPSS peripheral drivers.
622 config X86_AMD_PLATFORM_DEVICE
623 bool "AMD ACPI2Platform devices support"
628 Select to interpret AMD specific ACPI device to platform device
629 such as I2C, UART, GPIO found on AMD Carrizo and later chipsets.
630 I2C and UART depend on COMMON_CLK to set clock. GPIO driver is
631 implemented under PINCTRL subsystem.
634 tristate "Intel SoC IOSF Sideband support for SoC platforms"
637 This option enables sideband register access support for Intel SoC
638 platforms. On these platforms the IOSF sideband is used in lieu of
639 MSR's for some register accesses, mostly but not limited to thermal
640 and power. Drivers may query the availability of this device to
641 determine if they need the sideband in order to work on these
642 platforms. The sideband is available on the following SoC products.
643 This list is not meant to be exclusive.
648 You should say Y if you are running a kernel on one of these SoC's.
650 config IOSF_MBI_DEBUG
651 bool "Enable IOSF sideband access through debugfs"
652 depends on IOSF_MBI && DEBUG_FS
654 Select this option to expose the IOSF sideband access registers (MCR,
655 MDR, MCRX) through debugfs to write and read register information from
656 different units on the SoC. This is most useful for obtaining device
657 state information for debug and analysis. As this is a general access
658 mechanism, users of this option would have specific knowledge of the
659 device they want to access.
661 If you don't require the option or are in doubt, say N.
664 bool "RDC R-321x SoC"
666 depends on X86_EXTENDED_PLATFORM
668 select X86_REBOOTFIXUPS
670 This option is needed for RDC R-321x system-on-chip, also known
672 If you don't have one of these chips, you should say N here.
674 config X86_32_NON_STANDARD
675 bool "Support non-standard 32-bit SMP architectures"
676 depends on X86_32 && SMP
677 depends on X86_EXTENDED_PLATFORM
679 This option compiles in the bigsmp and STA2X11 default
680 subarchitectures. It is intended for a generic binary
681 kernel. If you select them all, kernel will probe it one by
682 one and will fallback to default.
684 # Alphabetically sorted list of Non standard 32 bit platforms
686 config X86_SUPPORTS_MEMORY_FAILURE
688 # MCE code calls memory_failure():
690 # On 32-bit this adds too big of NODES_SHIFT and we run out of page flags:
691 # On 32-bit SPARSEMEM adds too big of SECTIONS_WIDTH:
692 depends on X86_64 || !SPARSEMEM
693 select ARCH_SUPPORTS_MEMORY_FAILURE
696 bool "STA2X11 Companion Chip Support"
697 depends on X86_32_NON_STANDARD && PCI
698 select ARCH_HAS_PHYS_TO_DMA
699 select X86_DEV_DMA_OPS
706 This adds support for boards based on the STA2X11 IO-Hub,
707 a.k.a. "ConneXt". The chip is used in place of the standard
708 PC chipset, so all "standard" peripherals are missing. If this
709 option is selected the kernel will still be able to boot on
710 standard PC machines.
713 tristate "Eurobraille/Iris poweroff module"
716 The Iris machines from EuroBraille do not have APM or ACPI support
717 to shut themselves down properly. A special I/O sequence is
718 needed to do so, which is what this module does at
721 This is only for Iris machines from EuroBraille.
725 config SCHED_OMIT_FRAME_POINTER
727 prompt "Single-depth WCHAN output"
730 Calculate simpler /proc/<PID>/wchan values. If this option
731 is disabled then wchan values will recurse back to the
732 caller function. This provides more accurate wchan values,
733 at the expense of slightly more scheduling overhead.
735 If in doubt, say "Y".
737 menuconfig HYPERVISOR_GUEST
738 bool "Linux guest support"
740 Say Y here to enable options for running Linux under various hyper-
741 visors. This option enables basic hypervisor detection and platform
744 If you say N, all options in this submenu will be skipped and
745 disabled, and Linux guest support won't be built in.
750 bool "Enable paravirtualization code"
752 This changes the kernel so it can modify itself when it is run
753 under a hypervisor, potentially improving performance significantly
754 over full virtualization. However, when run without a hypervisor
755 the kernel is theoretically slower and slightly larger.
757 config PARAVIRT_DEBUG
758 bool "paravirt-ops debugging"
759 depends on PARAVIRT && DEBUG_KERNEL
761 Enable to debug paravirt_ops internals. Specifically, BUG if
762 a paravirt_op is missing when it is called.
764 config PARAVIRT_SPINLOCKS
765 bool "Paravirtualization layer for spinlocks"
766 depends on PARAVIRT && SMP
768 Paravirtualized spinlocks allow a pvops backend to replace the
769 spinlock implementation with something virtualization-friendly
770 (for example, block the virtual CPU rather than spinning).
772 It has a minimal impact on native kernels and gives a nice performance
773 benefit on paravirtualized KVM / Xen kernels.
775 If you are unsure how to answer this question, answer Y.
777 config QUEUED_LOCK_STAT
778 bool "Paravirt queued spinlock statistics"
779 depends on PARAVIRT_SPINLOCKS && DEBUG_FS
781 Enable the collection of statistical data on the slowpath
782 behavior of paravirtualized queued spinlocks and report
785 source "arch/x86/xen/Kconfig"
788 bool "KVM Guest support (including kvmclock)"
790 select PARAVIRT_CLOCK
793 This option enables various optimizations for running under the KVM
794 hypervisor. It includes a paravirtualized clock, so that instead
795 of relying on a PIT (or probably other) emulation by the
796 underlying device model, the host provides the guest with
797 timing infrastructure such as time of day, and system time
800 bool "Enable debug information for KVM Guests in debugfs"
801 depends on KVM_GUEST && DEBUG_FS
804 This option enables collection of various statistics for KVM guest.
805 Statistics are displayed in debugfs filesystem. Enabling this option
806 may incur significant overhead.
808 config PARAVIRT_TIME_ACCOUNTING
809 bool "Paravirtual steal time accounting"
813 Select this option to enable fine granularity task steal time
814 accounting. Time spent executing other tasks in parallel with
815 the current vCPU is discounted from the vCPU power. To account for
816 that, there can be a small performance impact.
818 If in doubt, say N here.
820 config PARAVIRT_CLOCK
823 config JAILHOUSE_GUEST
824 bool "Jailhouse non-root cell support"
825 depends on X86_64 && PCI
828 This option allows to run Linux as guest in a Jailhouse non-root
829 cell. You can leave this option disabled if you only want to start
830 Jailhouse and run Linux afterwards in the root cell.
832 endif #HYPERVISOR_GUEST
837 source "arch/x86/Kconfig.cpu"
841 prompt "HPET Timer Support" if X86_32
843 Use the IA-PC HPET (High Precision Event Timer) to manage
844 time in preference to the PIT and RTC, if a HPET is
846 HPET is the next generation timer replacing legacy 8254s.
847 The HPET provides a stable time base on SMP
848 systems, unlike the TSC, but it is more expensive to access,
849 as it is off-chip. The interface used is documented
850 in the HPET spec, revision 1.
852 You can safely choose Y here. However, HPET will only be
853 activated if the platform and the BIOS support this feature.
854 Otherwise the 8254 will be used for timing services.
856 Choose N to continue using the legacy 8254 timer.
858 config HPET_EMULATE_RTC
860 depends on HPET_TIMER && (RTC=y || RTC=m || RTC_DRV_CMOS=m || RTC_DRV_CMOS=y)
863 def_bool y if X86_INTEL_MID
864 prompt "Intel MID APB Timer Support" if X86_INTEL_MID
866 depends on X86_INTEL_MID && SFI
868 APB timer is the replacement for 8254, HPET on X86 MID platforms.
869 The APBT provides a stable time base on SMP
870 systems, unlike the TSC, but it is more expensive to access,
871 as it is off-chip. APB timers are always running regardless of CPU
872 C states, they are used as per CPU clockevent device when possible.
874 # Mark as expert because too many people got it wrong.
875 # The code disables itself when not needed.
878 select DMI_SCAN_MACHINE_NON_EFI_FALLBACK
879 bool "Enable DMI scanning" if EXPERT
881 Enabled scanning of DMI to identify machine quirks. Say Y
882 here unless you have verified that your setup is not
883 affected by entries in the DMI blacklist. Required by PNP
887 bool "Old AMD GART IOMMU support"
890 depends on X86_64 && PCI && AMD_NB
892 Provides a driver for older AMD Athlon64/Opteron/Turion/Sempron
893 GART based hardware IOMMUs.
895 The GART supports full DMA access for devices with 32-bit access
896 limitations, on systems with more than 3 GB. This is usually needed
897 for USB, sound, many IDE/SATA chipsets and some other devices.
899 Newer systems typically have a modern AMD IOMMU, supported via
900 the CONFIG_AMD_IOMMU=y config option.
902 In normal configurations this driver is only active when needed:
903 there's more than 3 GB of memory and the system contains a
904 32-bit limited device.
909 bool "IBM Calgary IOMMU support"
912 depends on X86_64 && PCI
914 Support for hardware IOMMUs in IBM's xSeries x366 and x460
915 systems. Needed to run systems with more than 3GB of memory
916 properly with 32-bit PCI devices that do not support DAC
917 (Double Address Cycle). Calgary also supports bus level
918 isolation, where all DMAs pass through the IOMMU. This
919 prevents them from going anywhere except their intended
920 destination. This catches hard-to-find kernel bugs and
921 mis-behaving drivers and devices that do not use the DMA-API
922 properly to set up their DMA buffers. The IOMMU can be
923 turned off at boot time with the iommu=off parameter.
924 Normally the kernel will make the right choice by itself.
927 config CALGARY_IOMMU_ENABLED_BY_DEFAULT
929 prompt "Should Calgary be enabled by default?"
930 depends on CALGARY_IOMMU
932 Should Calgary be enabled by default? if you choose 'y', Calgary
933 will be used (if it exists). If you choose 'n', Calgary will not be
934 used even if it exists. If you choose 'n' and would like to use
935 Calgary anyway, pass 'iommu=calgary' on the kernel command line.
939 bool "Enable Maximum number of SMP Processors and NUMA Nodes"
940 depends on X86_64 && SMP && DEBUG_KERNEL
941 select CPUMASK_OFFSTACK
943 Enable maximum number of CPUS and NUMA Nodes for this architecture.
947 # The maximum number of CPUs supported:
949 # The main config value is NR_CPUS, which defaults to NR_CPUS_DEFAULT,
950 # and which can be configured interactively in the
951 # [NR_CPUS_RANGE_BEGIN ... NR_CPUS_RANGE_END] range.
953 # The ranges are different on 32-bit and 64-bit kernels, depending on
954 # hardware capabilities and scalability features of the kernel.
956 # ( If MAXSMP is enabled we just use the highest possible value and disable
957 # interactive configuration. )
960 config NR_CPUS_RANGE_BEGIN
962 default NR_CPUS_RANGE_END if MAXSMP
966 config NR_CPUS_RANGE_END
969 default 64 if SMP && X86_BIGSMP
970 default 8 if SMP && !X86_BIGSMP
973 config NR_CPUS_RANGE_END
976 default 8192 if SMP && ( MAXSMP || CPUMASK_OFFSTACK)
977 default 512 if SMP && (!MAXSMP && !CPUMASK_OFFSTACK)
980 config NR_CPUS_DEFAULT
983 default 32 if X86_BIGSMP
987 config NR_CPUS_DEFAULT
990 default 8192 if MAXSMP
995 int "Maximum number of CPUs" if SMP && !MAXSMP
996 range NR_CPUS_RANGE_BEGIN NR_CPUS_RANGE_END
997 default NR_CPUS_DEFAULT
999 This allows you to specify the maximum number of CPUs which this
1000 kernel will support. If CPUMASK_OFFSTACK is enabled, the maximum
1001 supported value is 8192, otherwise the maximum value is 512. The
1002 minimum value which makes sense is 2.
1004 This is purely to save memory: each supported CPU adds about 8KB
1005 to the kernel image.
1008 bool "SMT (Hyperthreading) scheduler support"
1011 SMT scheduler support improves the CPU scheduler's decision making
1012 when dealing with Intel Pentium 4 chips with HyperThreading at a
1013 cost of slightly increased overhead in some places. If unsure say
1018 prompt "Multi-core scheduler support"
1021 Multi-core scheduler support improves the CPU scheduler's decision
1022 making when dealing with multi-core CPU chips at a cost of slightly
1023 increased overhead in some places. If unsure say N here.
1025 config SCHED_MC_PRIO
1026 bool "CPU core priorities scheduler support"
1027 depends on SCHED_MC && CPU_SUP_INTEL
1028 select X86_INTEL_PSTATE
1032 Intel Turbo Boost Max Technology 3.0 enabled CPUs have a
1033 core ordering determined at manufacturing time, which allows
1034 certain cores to reach higher turbo frequencies (when running
1035 single threaded workloads) than others.
1037 Enabling this kernel feature teaches the scheduler about
1038 the TBM3 (aka ITMT) priority order of the CPU cores and adjusts the
1039 scheduler's CPU selection logic accordingly, so that higher
1040 overall system performance can be achieved.
1042 This feature will have no effect on CPUs without this feature.
1044 If unsure say Y here.
1046 source "kernel/Kconfig.preempt"
1050 depends on !SMP && X86_LOCAL_APIC
1053 bool "Local APIC support on uniprocessors" if !PCI_MSI
1055 depends on X86_32 && !SMP && !X86_32_NON_STANDARD
1057 A local APIC (Advanced Programmable Interrupt Controller) is an
1058 integrated interrupt controller in the CPU. If you have a single-CPU
1059 system which has a processor with a local APIC, you can say Y here to
1060 enable and use it. If you say Y here even though your machine doesn't
1061 have a local APIC, then the kernel will still run with no slowdown at
1062 all. The local APIC supports CPU-generated self-interrupts (timer,
1063 performance counters), and the NMI watchdog which detects hard
1066 config X86_UP_IOAPIC
1067 bool "IO-APIC support on uniprocessors"
1068 depends on X86_UP_APIC
1070 An IO-APIC (I/O Advanced Programmable Interrupt Controller) is an
1071 SMP-capable replacement for PC-style interrupt controllers. Most
1072 SMP systems and many recent uniprocessor systems have one.
1074 If you have a single-CPU system with an IO-APIC, you can say Y here
1075 to use it. If you say Y here even though your machine doesn't have
1076 an IO-APIC, then the kernel will still run with no slowdown at all.
1078 config X86_LOCAL_APIC
1080 depends on X86_64 || SMP || X86_32_NON_STANDARD || X86_UP_APIC || PCI_MSI
1081 select IRQ_DOMAIN_HIERARCHY
1082 select PCI_MSI_IRQ_DOMAIN if PCI_MSI
1086 depends on X86_LOCAL_APIC || X86_UP_IOAPIC
1088 config X86_REROUTE_FOR_BROKEN_BOOT_IRQS
1089 bool "Reroute for broken boot IRQs"
1090 depends on X86_IO_APIC
1092 This option enables a workaround that fixes a source of
1093 spurious interrupts. This is recommended when threaded
1094 interrupt handling is used on systems where the generation of
1095 superfluous "boot interrupts" cannot be disabled.
1097 Some chipsets generate a legacy INTx "boot IRQ" when the IRQ
1098 entry in the chipset's IO-APIC is masked (as, e.g. the RT
1099 kernel does during interrupt handling). On chipsets where this
1100 boot IRQ generation cannot be disabled, this workaround keeps
1101 the original IRQ line masked so that only the equivalent "boot
1102 IRQ" is delivered to the CPUs. The workaround also tells the
1103 kernel to set up the IRQ handler on the boot IRQ line. In this
1104 way only one interrupt is delivered to the kernel. Otherwise
1105 the spurious second interrupt may cause the kernel to bring
1106 down (vital) interrupt lines.
1108 Only affects "broken" chipsets. Interrupt sharing may be
1109 increased on these systems.
1112 bool "Machine Check / overheating reporting"
1113 select GENERIC_ALLOCATOR
1116 Machine Check support allows the processor to notify the
1117 kernel if it detects a problem (e.g. overheating, data corruption).
1118 The action the kernel takes depends on the severity of the problem,
1119 ranging from warning messages to halting the machine.
1121 config X86_MCELOG_LEGACY
1122 bool "Support for deprecated /dev/mcelog character device"
1125 Enable support for /dev/mcelog which is needed by the old mcelog
1126 userspace logging daemon. Consider switching to the new generation
1129 config X86_MCE_INTEL
1131 prompt "Intel MCE features"
1132 depends on X86_MCE && X86_LOCAL_APIC
1134 Additional support for intel specific MCE features such as
1135 the thermal monitor.
1139 prompt "AMD MCE features"
1140 depends on X86_MCE && X86_LOCAL_APIC && AMD_NB
1142 Additional support for AMD specific MCE features such as
1143 the DRAM Error Threshold.
1145 config X86_ANCIENT_MCE
1146 bool "Support for old Pentium 5 / WinChip machine checks"
1147 depends on X86_32 && X86_MCE
1149 Include support for machine check handling on old Pentium 5 or WinChip
1150 systems. These typically need to be enabled explicitly on the command
1153 config X86_MCE_THRESHOLD
1154 depends on X86_MCE_AMD || X86_MCE_INTEL
1157 config X86_MCE_INJECT
1158 depends on X86_MCE && X86_LOCAL_APIC && DEBUG_FS
1159 tristate "Machine check injector support"
1161 Provide support for injecting machine checks for testing purposes.
1162 If you don't know what a machine check is and you don't do kernel
1163 QA it is safe to say n.
1165 config X86_THERMAL_VECTOR
1167 depends on X86_MCE_INTEL
1169 source "arch/x86/events/Kconfig"
1171 config X86_LEGACY_VM86
1172 bool "Legacy VM86 support"
1176 This option allows user programs to put the CPU into V8086
1177 mode, which is an 80286-era approximation of 16-bit real mode.
1179 Some very old versions of X and/or vbetool require this option
1180 for user mode setting. Similarly, DOSEMU will use it if
1181 available to accelerate real mode DOS programs. However, any
1182 recent version of DOSEMU, X, or vbetool should be fully
1183 functional even without kernel VM86 support, as they will all
1184 fall back to software emulation. Nevertheless, if you are using
1185 a 16-bit DOS program where 16-bit performance matters, vm86
1186 mode might be faster than emulation and you might want to
1189 Note that any app that works on a 64-bit kernel is unlikely to
1190 need this option, as 64-bit kernels don't, and can't, support
1191 V8086 mode. This option is also unrelated to 16-bit protected
1192 mode and is not needed to run most 16-bit programs under Wine.
1194 Enabling this option increases the complexity of the kernel
1195 and slows down exception handling a tiny bit.
1197 If unsure, say N here.
1201 default X86_LEGACY_VM86
1204 bool "Enable support for 16-bit segments" if EXPERT
1206 depends on MODIFY_LDT_SYSCALL
1208 This option is required by programs like Wine to run 16-bit
1209 protected mode legacy code on x86 processors. Disabling
1210 this option saves about 300 bytes on i386, or around 6K text
1211 plus 16K runtime memory on x86-64,
1215 depends on X86_16BIT && X86_32
1219 depends on X86_16BIT && X86_64
1221 config X86_VSYSCALL_EMULATION
1222 bool "Enable vsyscall emulation" if EXPERT
1226 This enables emulation of the legacy vsyscall page. Disabling
1227 it is roughly equivalent to booting with vsyscall=none, except
1228 that it will also disable the helpful warning if a program
1229 tries to use a vsyscall. With this option set to N, offending
1230 programs will just segfault, citing addresses of the form
1233 This option is required by many programs built before 2013, and
1234 care should be used even with newer programs if set to N.
1236 Disabling this option saves about 7K of kernel size and
1237 possibly 4K of additional runtime pagetable memory.
1240 tristate "Toshiba Laptop support"
1243 This adds a driver to safely access the System Management Mode of
1244 the CPU on Toshiba portables with a genuine Toshiba BIOS. It does
1245 not work on models with a Phoenix BIOS. The System Management Mode
1246 is used to set the BIOS and power saving options on Toshiba portables.
1248 For information on utilities to make use of this driver see the
1249 Toshiba Linux utilities web site at:
1250 <http://www.buzzard.org.uk/toshiba/>.
1252 Say Y if you intend to run this kernel on a Toshiba portable.
1256 tristate "Dell i8k legacy laptop support"
1258 select SENSORS_DELL_SMM
1260 This option enables legacy /proc/i8k userspace interface in hwmon
1261 dell-smm-hwmon driver. Character file /proc/i8k reports bios version,
1262 temperature and allows controlling fan speeds of Dell laptops via
1263 System Management Mode. For old Dell laptops (like Dell Inspiron 8000)
1264 it reports also power and hotkey status. For fan speed control is
1265 needed userspace package i8kutils.
1267 Say Y if you intend to run this kernel on old Dell laptops or want to
1268 use userspace package i8kutils.
1271 config X86_REBOOTFIXUPS
1272 bool "Enable X86 board specific fixups for reboot"
1275 This enables chipset and/or board specific fixups to be done
1276 in order to get reboot to work correctly. This is only needed on
1277 some combinations of hardware and BIOS. The symptom, for which
1278 this config is intended, is when reboot ends with a stalled/hung
1281 Currently, the only fixup is for the Geode machines using
1282 CS5530A and CS5536 chipsets and the RDC R-321x SoC.
1284 Say Y if you want to enable the fixup. Currently, it's safe to
1285 enable this option even if you don't need it.
1289 bool "CPU microcode loading support"
1291 depends on CPU_SUP_AMD || CPU_SUP_INTEL
1294 If you say Y here, you will be able to update the microcode on
1295 Intel and AMD processors. The Intel support is for the IA32 family,
1296 e.g. Pentium Pro, Pentium II, Pentium III, Pentium 4, Xeon etc. The
1297 AMD support is for families 0x10 and later. You will obviously need
1298 the actual microcode binary data itself which is not shipped with
1301 The preferred method to load microcode from a detached initrd is described
1302 in Documentation/x86/microcode.txt. For that you need to enable
1303 CONFIG_BLK_DEV_INITRD in order for the loader to be able to scan the
1304 initrd for microcode blobs.
1306 In addition, you can build the microcode into the kernel. For that you
1307 need to add the vendor-supplied microcode to the CONFIG_EXTRA_FIRMWARE
1310 config MICROCODE_INTEL
1311 bool "Intel microcode loading support"
1312 depends on MICROCODE
1316 This options enables microcode patch loading support for Intel
1319 For the current Intel microcode data package go to
1320 <https://downloadcenter.intel.com> and search for
1321 'Linux Processor Microcode Data File'.
1323 config MICROCODE_AMD
1324 bool "AMD microcode loading support"
1325 depends on MICROCODE
1328 If you select this option, microcode patch loading support for AMD
1329 processors will be enabled.
1331 config MICROCODE_OLD_INTERFACE
1333 depends on MICROCODE
1336 tristate "/dev/cpu/*/msr - Model-specific register support"
1338 This device gives privileged processes access to the x86
1339 Model-Specific Registers (MSRs). It is a character device with
1340 major 202 and minors 0 to 31 for /dev/cpu/0/msr to /dev/cpu/31/msr.
1341 MSR accesses are directed to a specific CPU on multi-processor
1345 tristate "/dev/cpu/*/cpuid - CPU information support"
1347 This device gives processes access to the x86 CPUID instruction to
1348 be executed on a specific processor. It is a character device
1349 with major 203 and minors 0 to 31 for /dev/cpu/0/cpuid to
1353 prompt "High Memory Support"
1360 Linux can use up to 64 Gigabytes of physical memory on x86 systems.
1361 However, the address space of 32-bit x86 processors is only 4
1362 Gigabytes large. That means that, if you have a large amount of
1363 physical memory, not all of it can be "permanently mapped" by the
1364 kernel. The physical memory that's not permanently mapped is called
1367 If you are compiling a kernel which will never run on a machine with
1368 more than 1 Gigabyte total physical RAM, answer "off" here (default
1369 choice and suitable for most users). This will result in a "3GB/1GB"
1370 split: 3GB are mapped so that each process sees a 3GB virtual memory
1371 space and the remaining part of the 4GB virtual memory space is used
1372 by the kernel to permanently map as much physical memory as
1375 If the machine has between 1 and 4 Gigabytes physical RAM, then
1378 If more than 4 Gigabytes is used then answer "64GB" here. This
1379 selection turns Intel PAE (Physical Address Extension) mode on.
1380 PAE implements 3-level paging on IA32 processors. PAE is fully
1381 supported by Linux, PAE mode is implemented on all recent Intel
1382 processors (Pentium Pro and better). NOTE: If you say "64GB" here,
1383 then the kernel will not boot on CPUs that don't support PAE!
1385 The actual amount of total physical memory will either be
1386 auto detected or can be forced by using a kernel command line option
1387 such as "mem=256M". (Try "man bootparam" or see the documentation of
1388 your boot loader (lilo or loadlin) about how to pass options to the
1389 kernel at boot time.)
1391 If unsure, say "off".
1396 Select this if you have a 32-bit processor and between 1 and 4
1397 gigabytes of physical RAM.
1401 depends on !M486 && !M586 && !M586TSC && !M586MMX && !MGEODE_LX && !MGEODEGX1 && !MCYRIXIII && !MELAN && !MWINCHIPC6 && !WINCHIP3D && !MK6
1404 Select this if you have a 32-bit processor and more than 4
1405 gigabytes of physical RAM.
1410 prompt "Memory split" if EXPERT
1414 Select the desired split between kernel and user memory.
1416 If the address range available to the kernel is less than the
1417 physical memory installed, the remaining memory will be available
1418 as "high memory". Accessing high memory is a little more costly
1419 than low memory, as it needs to be mapped into the kernel first.
1420 Note that increasing the kernel address space limits the range
1421 available to user programs, making the address space there
1422 tighter. Selecting anything other than the default 3G/1G split
1423 will also likely make your kernel incompatible with binary-only
1426 If you are not absolutely sure what you are doing, leave this
1430 bool "3G/1G user/kernel split"
1431 config VMSPLIT_3G_OPT
1433 bool "3G/1G user/kernel split (for full 1G low memory)"
1435 bool "2G/2G user/kernel split"
1436 config VMSPLIT_2G_OPT
1438 bool "2G/2G user/kernel split (for full 2G low memory)"
1440 bool "1G/3G user/kernel split"
1445 default 0xB0000000 if VMSPLIT_3G_OPT
1446 default 0x80000000 if VMSPLIT_2G
1447 default 0x78000000 if VMSPLIT_2G_OPT
1448 default 0x40000000 if VMSPLIT_1G
1454 depends on X86_32 && (HIGHMEM64G || HIGHMEM4G)
1457 bool "PAE (Physical Address Extension) Support"
1458 depends on X86_32 && !HIGHMEM4G
1459 select PHYS_ADDR_T_64BIT
1462 PAE is required for NX support, and furthermore enables
1463 larger swapspace support for non-overcommit purposes. It
1464 has the cost of more pagetable lookup overhead, and also
1465 consumes more pagetable space per process.
1468 bool "Enable 5-level page tables support"
1469 select DYNAMIC_MEMORY_LAYOUT
1470 select SPARSEMEM_VMEMMAP
1473 5-level paging enables access to larger address space:
1474 upto 128 PiB of virtual address space and 4 PiB of
1475 physical address space.
1477 It will be supported by future Intel CPUs.
1479 A kernel with the option enabled can be booted on machines that
1480 support 4- or 5-level paging.
1482 See Documentation/x86/x86_64/5level-paging.txt for more
1487 config X86_DIRECT_GBPAGES
1489 depends on X86_64 && !DEBUG_PAGEALLOC
1491 Certain kernel features effectively disable kernel
1492 linear 1 GB mappings (even if the CPU otherwise
1493 supports them), so don't confuse the user by printing
1494 that we have them enabled.
1496 config ARCH_HAS_MEM_ENCRYPT
1499 config AMD_MEM_ENCRYPT
1500 bool "AMD Secure Memory Encryption (SME) support"
1501 depends on X86_64 && CPU_SUP_AMD
1502 select DYNAMIC_PHYSICAL_MASK
1504 Say yes to enable support for the encryption of system memory.
1505 This requires an AMD processor that supports Secure Memory
1508 config AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT
1509 bool "Activate AMD Secure Memory Encryption (SME) by default"
1511 depends on AMD_MEM_ENCRYPT
1513 Say yes to have system memory encrypted by default if running on
1514 an AMD processor that supports Secure Memory Encryption (SME).
1516 If set to Y, then the encryption of system memory can be
1517 deactivated with the mem_encrypt=off command line option.
1519 If set to N, then the encryption of system memory can be
1520 activated with the mem_encrypt=on command line option.
1522 config ARCH_USE_MEMREMAP_PROT
1524 depends on AMD_MEM_ENCRYPT
1526 # Common NUMA Features
1528 bool "Numa Memory Allocation and Scheduler Support"
1530 depends on X86_64 || (X86_32 && HIGHMEM64G && X86_BIGSMP)
1531 default y if X86_BIGSMP
1533 Enable NUMA (Non Uniform Memory Access) support.
1535 The kernel will try to allocate memory used by a CPU on the
1536 local memory controller of the CPU and add some more
1537 NUMA awareness to the kernel.
1539 For 64-bit this is recommended if the system is Intel Core i7
1540 (or later), AMD Opteron, or EM64T NUMA.
1542 For 32-bit this is only needed if you boot a 32-bit
1543 kernel on a 64-bit NUMA platform.
1545 Otherwise, you should say N.
1549 prompt "Old style AMD Opteron NUMA detection"
1550 depends on X86_64 && NUMA && PCI
1552 Enable AMD NUMA node topology detection. You should say Y here if
1553 you have a multi processor AMD system. This uses an old method to
1554 read the NUMA configuration directly from the builtin Northbridge
1555 of Opteron. It is recommended to use X86_64_ACPI_NUMA instead,
1556 which also takes priority if both are compiled in.
1558 config X86_64_ACPI_NUMA
1560 prompt "ACPI NUMA detection"
1561 depends on X86_64 && NUMA && ACPI && PCI
1564 Enable ACPI SRAT based node topology detection.
1566 # Some NUMA nodes have memory ranges that span
1567 # other nodes. Even though a pfn is valid and
1568 # between a node's start and end pfns, it may not
1569 # reside on that node. See memmap_init_zone()
1571 config NODES_SPAN_OTHER_NODES
1573 depends on X86_64_ACPI_NUMA
1576 bool "NUMA emulation"
1579 Enable NUMA emulation. A flat machine will be split
1580 into virtual nodes when booted with "numa=fake=N", where N is the
1581 number of nodes. This is only useful for debugging.
1584 int "Maximum NUMA Nodes (as a power of 2)" if !MAXSMP
1586 default "10" if MAXSMP
1587 default "6" if X86_64
1589 depends on NEED_MULTIPLE_NODES
1591 Specify the maximum number of NUMA Nodes available on the target
1592 system. Increases memory reserved to accommodate various tables.
1594 config ARCH_HAVE_MEMORY_PRESENT
1596 depends on X86_32 && DISCONTIGMEM
1598 config ARCH_FLATMEM_ENABLE
1600 depends on X86_32 && !NUMA
1602 config ARCH_DISCONTIGMEM_ENABLE
1604 depends on NUMA && X86_32
1606 config ARCH_DISCONTIGMEM_DEFAULT
1608 depends on NUMA && X86_32
1610 config ARCH_SPARSEMEM_ENABLE
1612 depends on X86_64 || NUMA || X86_32 || X86_32_NON_STANDARD
1613 select SPARSEMEM_STATIC if X86_32
1614 select SPARSEMEM_VMEMMAP_ENABLE if X86_64
1616 config ARCH_SPARSEMEM_DEFAULT
1620 config ARCH_SELECT_MEMORY_MODEL
1622 depends on ARCH_SPARSEMEM_ENABLE
1624 config ARCH_MEMORY_PROBE
1625 bool "Enable sysfs memory/probe interface"
1626 depends on X86_64 && MEMORY_HOTPLUG
1628 This option enables a sysfs memory/probe interface for testing.
1629 See Documentation/memory-hotplug.txt for more information.
1630 If you are unsure how to answer this question, answer N.
1632 config ARCH_PROC_KCORE_TEXT
1634 depends on X86_64 && PROC_KCORE
1636 config ILLEGAL_POINTER_VALUE
1639 default 0xdead000000000000 if X86_64
1643 config X86_PMEM_LEGACY_DEVICE
1646 config X86_PMEM_LEGACY
1647 tristate "Support non-standard NVDIMMs and ADR protected memory"
1648 depends on PHYS_ADDR_T_64BIT
1650 select X86_PMEM_LEGACY_DEVICE
1653 Treat memory marked using the non-standard e820 type of 12 as used
1654 by the Intel Sandy Bridge-EP reference BIOS as protected memory.
1655 The kernel will offer these regions to the 'pmem' driver so
1656 they can be used for persistent storage.
1661 bool "Allocate 3rd-level pagetables from highmem"
1664 The VM uses one page table entry for each page of physical memory.
1665 For systems with a lot of RAM, this can be wasteful of precious
1666 low memory. Setting this option will put user-space page table
1667 entries in high memory.
1669 config X86_CHECK_BIOS_CORRUPTION
1670 bool "Check for low memory corruption"
1672 Periodically check for memory corruption in low memory, which
1673 is suspected to be caused by BIOS. Even when enabled in the
1674 configuration, it is disabled at runtime. Enable it by
1675 setting "memory_corruption_check=1" on the kernel command
1676 line. By default it scans the low 64k of memory every 60
1677 seconds; see the memory_corruption_check_size and
1678 memory_corruption_check_period parameters in
1679 Documentation/admin-guide/kernel-parameters.rst to adjust this.
1681 When enabled with the default parameters, this option has
1682 almost no overhead, as it reserves a relatively small amount
1683 of memory and scans it infrequently. It both detects corruption
1684 and prevents it from affecting the running system.
1686 It is, however, intended as a diagnostic tool; if repeatable
1687 BIOS-originated corruption always affects the same memory,
1688 you can use memmap= to prevent the kernel from using that
1691 config X86_BOOTPARAM_MEMORY_CORRUPTION_CHECK
1692 bool "Set the default setting of memory_corruption_check"
1693 depends on X86_CHECK_BIOS_CORRUPTION
1696 Set whether the default state of memory_corruption_check is
1699 config X86_RESERVE_LOW
1700 int "Amount of low memory, in kilobytes, to reserve for the BIOS"
1704 Specify the amount of low memory to reserve for the BIOS.
1706 The first page contains BIOS data structures that the kernel
1707 must not use, so that page must always be reserved.
1709 By default we reserve the first 64K of physical RAM, as a
1710 number of BIOSes are known to corrupt that memory range
1711 during events such as suspend/resume or monitor cable
1712 insertion, so it must not be used by the kernel.
1714 You can set this to 4 if you are absolutely sure that you
1715 trust the BIOS to get all its memory reservations and usages
1716 right. If you know your BIOS have problems beyond the
1717 default 64K area, you can set this to 640 to avoid using the
1718 entire low memory range.
1720 If you have doubts about the BIOS (e.g. suspend/resume does
1721 not work or there's kernel crashes after certain hardware
1722 hotplug events) then you might want to enable
1723 X86_CHECK_BIOS_CORRUPTION=y to allow the kernel to check
1724 typical corruption patterns.
1726 Leave this to the default value of 64 if you are unsure.
1728 config MATH_EMULATION
1730 depends on MODIFY_LDT_SYSCALL
1731 prompt "Math emulation" if X86_32
1733 Linux can emulate a math coprocessor (used for floating point
1734 operations) if you don't have one. 486DX and Pentium processors have
1735 a math coprocessor built in, 486SX and 386 do not, unless you added
1736 a 487DX or 387, respectively. (The messages during boot time can
1737 give you some hints here ["man dmesg"].) Everyone needs either a
1738 coprocessor or this emulation.
1740 If you don't have a math coprocessor, you need to say Y here; if you
1741 say Y here even though you have a coprocessor, the coprocessor will
1742 be used nevertheless. (This behavior can be changed with the kernel
1743 command line option "no387", which comes handy if your coprocessor
1744 is broken. Try "man bootparam" or see the documentation of your boot
1745 loader (lilo or loadlin) about how to pass options to the kernel at
1746 boot time.) This means that it is a good idea to say Y here if you
1747 intend to use this kernel on different machines.
1749 More information about the internals of the Linux math coprocessor
1750 emulation can be found in <file:arch/x86/math-emu/README>.
1752 If you are not sure, say Y; apart from resulting in a 66 KB bigger
1753 kernel, it won't hurt.
1757 prompt "MTRR (Memory Type Range Register) support" if EXPERT
1759 On Intel P6 family processors (Pentium Pro, Pentium II and later)
1760 the Memory Type Range Registers (MTRRs) may be used to control
1761 processor access to memory ranges. This is most useful if you have
1762 a video (VGA) card on a PCI or AGP bus. Enabling write-combining
1763 allows bus write transfers to be combined into a larger transfer
1764 before bursting over the PCI/AGP bus. This can increase performance
1765 of image write operations 2.5 times or more. Saying Y here creates a
1766 /proc/mtrr file which may be used to manipulate your processor's
1767 MTRRs. Typically the X server should use this.
1769 This code has a reasonably generic interface so that similar
1770 control registers on other processors can be easily supported
1773 The Cyrix 6x86, 6x86MX and M II processors have Address Range
1774 Registers (ARRs) which provide a similar functionality to MTRRs. For
1775 these, the ARRs are used to emulate the MTRRs.
1776 The AMD K6-2 (stepping 8 and above) and K6-3 processors have two
1777 MTRRs. The Centaur C6 (WinChip) has 8 MCRs, allowing
1778 write-combining. All of these processors are supported by this code
1779 and it makes sense to say Y here if you have one of them.
1781 Saying Y here also fixes a problem with buggy SMP BIOSes which only
1782 set the MTRRs for the boot CPU and not for the secondary CPUs. This
1783 can lead to all sorts of problems, so it's good to say Y here.
1785 You can safely say Y even if your machine doesn't have MTRRs, you'll
1786 just add about 9 KB to your kernel.
1788 See <file:Documentation/x86/mtrr.txt> for more information.
1790 config MTRR_SANITIZER
1792 prompt "MTRR cleanup support"
1795 Convert MTRR layout from continuous to discrete, so X drivers can
1796 add writeback entries.
1798 Can be disabled with disable_mtrr_cleanup on the kernel command line.
1799 The largest mtrr entry size for a continuous block can be set with
1804 config MTRR_SANITIZER_ENABLE_DEFAULT
1805 int "MTRR cleanup enable value (0-1)"
1808 depends on MTRR_SANITIZER
1810 Enable mtrr cleanup default value
1812 config MTRR_SANITIZER_SPARE_REG_NR_DEFAULT
1813 int "MTRR cleanup spare reg num (0-7)"
1816 depends on MTRR_SANITIZER
1818 mtrr cleanup spare entries default, it can be changed via
1819 mtrr_spare_reg_nr=N on the kernel command line.
1823 prompt "x86 PAT support" if EXPERT
1826 Use PAT attributes to setup page level cache control.
1828 PATs are the modern equivalents of MTRRs and are much more
1829 flexible than MTRRs.
1831 Say N here if you see bootup problems (boot crash, boot hang,
1832 spontaneous reboots) or a non-working video driver.
1836 config ARCH_USES_PG_UNCACHED
1842 prompt "x86 architectural random number generator" if EXPERT
1844 Enable the x86 architectural RDRAND instruction
1845 (Intel Bull Mountain technology) to generate random numbers.
1846 If supported, this is a high bandwidth, cryptographically
1847 secure hardware random number generator.
1851 prompt "Supervisor Mode Access Prevention" if EXPERT
1853 Supervisor Mode Access Prevention (SMAP) is a security
1854 feature in newer Intel processors. There is a small
1855 performance cost if this enabled and turned on; there is
1856 also a small increase in the kernel size if this is enabled.
1860 config X86_INTEL_UMIP
1862 depends on CPU_SUP_INTEL
1863 prompt "Intel User Mode Instruction Prevention" if EXPERT
1865 The User Mode Instruction Prevention (UMIP) is a security
1866 feature in newer Intel processors. If enabled, a general
1867 protection fault is issued if the SGDT, SLDT, SIDT, SMSW
1868 or STR instructions are executed in user mode. These instructions
1869 unnecessarily expose information about the hardware state.
1871 The vast majority of applications do not use these instructions.
1872 For the very few that do, software emulation is provided in
1873 specific cases in protected and virtual-8086 modes. Emulated
1876 config X86_INTEL_MPX
1877 prompt "Intel MPX (Memory Protection Extensions)"
1879 # Note: only available in 64-bit mode due to VMA flags shortage
1880 depends on CPU_SUP_INTEL && X86_64
1881 select ARCH_USES_HIGH_VMA_FLAGS
1883 MPX provides hardware features that can be used in
1884 conjunction with compiler-instrumented code to check
1885 memory references. It is designed to detect buffer
1886 overflow or underflow bugs.
1888 This option enables running applications which are
1889 instrumented or otherwise use MPX. It does not use MPX
1890 itself inside the kernel or to protect the kernel
1891 against bad memory references.
1893 Enabling this option will make the kernel larger:
1894 ~8k of kernel text and 36 bytes of data on a 64-bit
1895 defconfig. It adds a long to the 'mm_struct' which
1896 will increase the kernel memory overhead of each
1897 process and adds some branches to paths used during
1898 exec() and munmap().
1900 For details, see Documentation/x86/intel_mpx.txt
1904 config X86_INTEL_MEMORY_PROTECTION_KEYS
1905 prompt "Intel Memory Protection Keys"
1907 # Note: only available in 64-bit mode
1908 depends on CPU_SUP_INTEL && X86_64
1909 select ARCH_USES_HIGH_VMA_FLAGS
1910 select ARCH_HAS_PKEYS
1912 Memory Protection Keys provides a mechanism for enforcing
1913 page-based protections, but without requiring modification of the
1914 page tables when an application changes protection domains.
1916 For details, see Documentation/x86/protection-keys.txt
1921 bool "EFI runtime service support"
1924 select EFI_RUNTIME_WRAPPERS
1926 This enables the kernel to use EFI runtime services that are
1927 available (such as the EFI variable services).
1929 This option is only useful on systems that have EFI firmware.
1930 In addition, you should use the latest ELILO loader available
1931 at <http://elilo.sourceforge.net> in order to take advantage
1932 of EFI runtime services. However, even with this option, the
1933 resultant kernel should continue to boot on existing non-EFI
1937 bool "EFI stub support"
1938 depends on EFI && !X86_USE_3DNOW
1941 This kernel feature allows a bzImage to be loaded directly
1942 by EFI firmware without the use of a bootloader.
1944 See Documentation/efi-stub.txt for more information.
1947 bool "EFI mixed-mode support"
1948 depends on EFI_STUB && X86_64
1950 Enabling this feature allows a 64-bit kernel to be booted
1951 on a 32-bit firmware, provided that your CPU supports 64-bit
1954 Note that it is not possible to boot a mixed-mode enabled
1955 kernel via the EFI boot stub - a bootloader that supports
1956 the EFI handover protocol must be used.
1962 prompt "Enable seccomp to safely compute untrusted bytecode"
1964 This kernel feature is useful for number crunching applications
1965 that may need to compute untrusted bytecode during their
1966 execution. By using pipes or other transports made available to
1967 the process as file descriptors supporting the read/write
1968 syscalls, it's possible to isolate those applications in
1969 their own address space using seccomp. Once seccomp is
1970 enabled via prctl(PR_SET_SECCOMP), it cannot be disabled
1971 and the task is only allowed to execute a few safe syscalls
1972 defined by each seccomp mode.
1974 If unsure, say Y. Only embedded should say N here.
1976 source kernel/Kconfig.hz
1979 bool "kexec system call"
1982 kexec is a system call that implements the ability to shutdown your
1983 current kernel, and to start another kernel. It is like a reboot
1984 but it is independent of the system firmware. And like a reboot
1985 you can start any kernel with it, not just Linux.
1987 The name comes from the similarity to the exec system call.
1989 It is an ongoing process to be certain the hardware in a machine
1990 is properly shutdown, so do not be surprised if this code does not
1991 initially work for you. As of this writing the exact hardware
1992 interface is strongly in flux, so no good recommendation can be
1996 bool "kexec file based system call"
2001 depends on CRYPTO_SHA256=y
2003 This is new version of kexec system call. This system call is
2004 file based and takes file descriptors as system call argument
2005 for kernel and initramfs as opposed to list of segments as
2006 accepted by previous system call.
2008 config ARCH_HAS_KEXEC_PURGATORY
2011 config KEXEC_VERIFY_SIG
2012 bool "Verify kernel signature during kexec_file_load() syscall"
2013 depends on KEXEC_FILE
2015 This option makes kernel signature verification mandatory for
2016 the kexec_file_load() syscall.
2018 In addition to that option, you need to enable signature
2019 verification for the corresponding kernel image type being
2020 loaded in order for this to work.
2022 config KEXEC_BZIMAGE_VERIFY_SIG
2023 bool "Enable bzImage signature verification support"
2024 depends on KEXEC_VERIFY_SIG
2025 depends on SIGNED_PE_FILE_VERIFICATION
2026 select SYSTEM_TRUSTED_KEYRING
2028 Enable bzImage signature verification support.
2031 bool "kernel crash dumps"
2032 depends on X86_64 || (X86_32 && HIGHMEM)
2034 Generate crash dump after being started by kexec.
2035 This should be normally only set in special crash dump kernels
2036 which are loaded in the main kernel with kexec-tools into
2037 a specially reserved region and then later executed after
2038 a crash by kdump/kexec. The crash dump kernel must be compiled
2039 to a memory address not used by the main kernel or BIOS using
2040 PHYSICAL_START, or it must be built as a relocatable image
2041 (CONFIG_RELOCATABLE=y).
2042 For more details see Documentation/kdump/kdump.txt
2046 depends on KEXEC && HIBERNATION
2048 Jump between original kernel and kexeced kernel and invoke
2049 code in physical address mode via KEXEC
2051 config PHYSICAL_START
2052 hex "Physical address where the kernel is loaded" if (EXPERT || CRASH_DUMP)
2055 This gives the physical address where the kernel is loaded.
2057 If kernel is a not relocatable (CONFIG_RELOCATABLE=n) then
2058 bzImage will decompress itself to above physical address and
2059 run from there. Otherwise, bzImage will run from the address where
2060 it has been loaded by the boot loader and will ignore above physical
2063 In normal kdump cases one does not have to set/change this option
2064 as now bzImage can be compiled as a completely relocatable image
2065 (CONFIG_RELOCATABLE=y) and be used to load and run from a different
2066 address. This option is mainly useful for the folks who don't want
2067 to use a bzImage for capturing the crash dump and want to use a
2068 vmlinux instead. vmlinux is not relocatable hence a kernel needs
2069 to be specifically compiled to run from a specific memory area
2070 (normally a reserved region) and this option comes handy.
2072 So if you are using bzImage for capturing the crash dump,
2073 leave the value here unchanged to 0x1000000 and set
2074 CONFIG_RELOCATABLE=y. Otherwise if you plan to use vmlinux
2075 for capturing the crash dump change this value to start of
2076 the reserved region. In other words, it can be set based on
2077 the "X" value as specified in the "crashkernel=YM@XM"
2078 command line boot parameter passed to the panic-ed
2079 kernel. Please take a look at Documentation/kdump/kdump.txt
2080 for more details about crash dumps.
2082 Usage of bzImage for capturing the crash dump is recommended as
2083 one does not have to build two kernels. Same kernel can be used
2084 as production kernel and capture kernel. Above option should have
2085 gone away after relocatable bzImage support is introduced. But it
2086 is present because there are users out there who continue to use
2087 vmlinux for dump capture. This option should go away down the
2090 Don't change this unless you know what you are doing.
2093 bool "Build a relocatable kernel"
2096 This builds a kernel image that retains relocation information
2097 so it can be loaded someplace besides the default 1MB.
2098 The relocations tend to make the kernel binary about 10% larger,
2099 but are discarded at runtime.
2101 One use is for the kexec on panic case where the recovery kernel
2102 must live at a different physical address than the primary
2105 Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address
2106 it has been loaded at and the compile time physical address
2107 (CONFIG_PHYSICAL_START) is used as the minimum location.
2109 config RANDOMIZE_BASE
2110 bool "Randomize the address of the kernel image (KASLR)"
2111 depends on RELOCATABLE
2114 In support of Kernel Address Space Layout Randomization (KASLR),
2115 this randomizes the physical address at which the kernel image
2116 is decompressed and the virtual address where the kernel
2117 image is mapped, as a security feature that deters exploit
2118 attempts relying on knowledge of the location of kernel
2121 On 64-bit, the kernel physical and virtual addresses are
2122 randomized separately. The physical address will be anywhere
2123 between 16MB and the top of physical memory (up to 64TB). The
2124 virtual address will be randomized from 16MB up to 1GB (9 bits
2125 of entropy). Note that this also reduces the memory space
2126 available to kernel modules from 1.5GB to 1GB.
2128 On 32-bit, the kernel physical and virtual addresses are
2129 randomized together. They will be randomized from 16MB up to
2130 512MB (8 bits of entropy).
2132 Entropy is generated using the RDRAND instruction if it is
2133 supported. If RDTSC is supported, its value is mixed into
2134 the entropy pool as well. If neither RDRAND nor RDTSC are
2135 supported, then entropy is read from the i8254 timer. The
2136 usable entropy is limited by the kernel being built using
2137 2GB addressing, and that PHYSICAL_ALIGN must be at a
2138 minimum of 2MB. As a result, only 10 bits of entropy are
2139 theoretically possible, but the implementations are further
2140 limited due to memory layouts.
2144 # Relocation on x86 needs some additional build support
2145 config X86_NEED_RELOCS
2147 depends on RANDOMIZE_BASE || (X86_32 && RELOCATABLE)
2149 config PHYSICAL_ALIGN
2150 hex "Alignment value to which kernel should be aligned"
2152 range 0x2000 0x1000000 if X86_32
2153 range 0x200000 0x1000000 if X86_64
2155 This value puts the alignment restrictions on physical address
2156 where kernel is loaded and run from. Kernel is compiled for an
2157 address which meets above alignment restriction.
2159 If bootloader loads the kernel at a non-aligned address and
2160 CONFIG_RELOCATABLE is set, kernel will move itself to nearest
2161 address aligned to above value and run from there.
2163 If bootloader loads the kernel at a non-aligned address and
2164 CONFIG_RELOCATABLE is not set, kernel will ignore the run time
2165 load address and decompress itself to the address it has been
2166 compiled for and run from there. The address for which kernel is
2167 compiled already meets above alignment restrictions. Hence the
2168 end result is that kernel runs from a physical address meeting
2169 above alignment restrictions.
2171 On 32-bit this value must be a multiple of 0x2000. On 64-bit
2172 this value must be a multiple of 0x200000.
2174 Don't change this unless you know what you are doing.
2176 config DYNAMIC_MEMORY_LAYOUT
2179 This option makes base addresses of vmalloc and vmemmap as well as
2180 __PAGE_OFFSET movable during boot.
2182 config RANDOMIZE_MEMORY
2183 bool "Randomize the kernel memory sections"
2185 depends on RANDOMIZE_BASE
2186 select DYNAMIC_MEMORY_LAYOUT
2187 default RANDOMIZE_BASE
2189 Randomizes the base virtual address of kernel memory sections
2190 (physical memory mapping, vmalloc & vmemmap). This security feature
2191 makes exploits relying on predictable memory locations less reliable.
2193 The order of allocations remains unchanged. Entropy is generated in
2194 the same way as RANDOMIZE_BASE. Current implementation in the optimal
2195 configuration have in average 30,000 different possible virtual
2196 addresses for each memory section.
2200 config RANDOMIZE_MEMORY_PHYSICAL_PADDING
2201 hex "Physical memory mapping padding" if EXPERT
2202 depends on RANDOMIZE_MEMORY
2203 default "0xa" if MEMORY_HOTPLUG
2205 range 0x1 0x40 if MEMORY_HOTPLUG
2208 Define the padding in terabytes added to the existing physical
2209 memory size during kernel memory randomization. It is useful
2210 for memory hotplug support but reduces the entropy available for
2211 address randomization.
2213 If unsure, leave at the default value.
2216 bool "Support for hot-pluggable CPUs"
2219 Say Y here to allow turning CPUs off and on. CPUs can be
2220 controlled through /sys/devices/system/cpu.
2221 ( Note: power management support will enable this option
2222 automatically on SMP systems. )
2223 Say N if you want to disable CPU hotplug.
2225 config BOOTPARAM_HOTPLUG_CPU0
2226 bool "Set default setting of cpu0_hotpluggable"
2228 depends on HOTPLUG_CPU
2230 Set whether default state of cpu0_hotpluggable is on or off.
2232 Say Y here to enable CPU0 hotplug by default. If this switch
2233 is turned on, there is no need to give cpu0_hotplug kernel
2234 parameter and the CPU0 hotplug feature is enabled by default.
2236 Please note: there are two known CPU0 dependencies if you want
2237 to enable the CPU0 hotplug feature either by this switch or by
2238 cpu0_hotplug kernel parameter.
2240 First, resume from hibernate or suspend always starts from CPU0.
2241 So hibernate and suspend are prevented if CPU0 is offline.
2243 Second dependency is PIC interrupts always go to CPU0. CPU0 can not
2244 offline if any interrupt can not migrate out of CPU0. There may
2245 be other CPU0 dependencies.
2247 Please make sure the dependencies are under your control before
2248 you enable this feature.
2250 Say N if you don't want to enable CPU0 hotplug feature by default.
2251 You still can enable the CPU0 hotplug feature at boot by kernel
2252 parameter cpu0_hotplug.
2254 config DEBUG_HOTPLUG_CPU0
2256 prompt "Debug CPU0 hotplug"
2257 depends on HOTPLUG_CPU
2259 Enabling this option offlines CPU0 (if CPU0 can be offlined) as
2260 soon as possible and boots up userspace with CPU0 offlined. User
2261 can online CPU0 back after boot time.
2263 To debug CPU0 hotplug, you need to enable CPU0 offline/online
2264 feature by either turning on CONFIG_BOOTPARAM_HOTPLUG_CPU0 during
2265 compilation or giving cpu0_hotplug kernel parameter at boot.
2271 prompt "Disable the 32-bit vDSO (needed for glibc 2.3.3)"
2272 depends on COMPAT_32
2274 Certain buggy versions of glibc will crash if they are
2275 presented with a 32-bit vDSO that is not mapped at the address
2276 indicated in its segment table.
2278 The bug was introduced by f866314b89d56845f55e6f365e18b31ec978ec3a
2279 and fixed by 3b3ddb4f7db98ec9e912ccdf54d35df4aa30e04a and
2280 49ad572a70b8aeb91e57483a11dd1b77e31c4468. Glibc 2.3.3 is
2281 the only released version with the bug, but OpenSUSE 9
2282 contains a buggy "glibc 2.3.2".
2284 The symptom of the bug is that everything crashes on startup, saying:
2285 dl_main: Assertion `(void *) ph->p_vaddr == _rtld_local._dl_sysinfo_dso' failed!
2287 Saying Y here changes the default value of the vdso32 boot
2288 option from 1 to 0, which turns off the 32-bit vDSO entirely.
2289 This works around the glibc bug but hurts performance.
2291 If unsure, say N: if you are compiling your own kernel, you
2292 are unlikely to be using a buggy version of glibc.
2295 prompt "vsyscall table for legacy applications"
2297 default LEGACY_VSYSCALL_EMULATE
2299 Legacy user code that does not know how to find the vDSO expects
2300 to be able to issue three syscalls by calling fixed addresses in
2301 kernel space. Since this location is not randomized with ASLR,
2302 it can be used to assist security vulnerability exploitation.
2304 This setting can be changed at boot time via the kernel command
2305 line parameter vsyscall=[emulate|none].
2307 On a system with recent enough glibc (2.14 or newer) and no
2308 static binaries, you can say None without a performance penalty
2309 to improve security.
2311 If unsure, select "Emulate".
2313 config LEGACY_VSYSCALL_EMULATE
2316 The kernel traps and emulates calls into the fixed
2317 vsyscall address mapping. This makes the mapping
2318 non-executable, but it still contains known contents,
2319 which could be used in certain rare security vulnerability
2320 exploits. This configuration is recommended when userspace
2321 still uses the vsyscall area.
2323 config LEGACY_VSYSCALL_NONE
2326 There will be no vsyscall mapping at all. This will
2327 eliminate any risk of ASLR bypass due to the vsyscall
2328 fixed address mapping. Attempts to use the vsyscalls
2329 will be reported to dmesg, so that either old or
2330 malicious userspace programs can be identified.
2335 bool "Built-in kernel command line"
2337 Allow for specifying boot arguments to the kernel at
2338 build time. On some systems (e.g. embedded ones), it is
2339 necessary or convenient to provide some or all of the
2340 kernel boot arguments with the kernel itself (that is,
2341 to not rely on the boot loader to provide them.)
2343 To compile command line arguments into the kernel,
2344 set this option to 'Y', then fill in the
2345 boot arguments in CONFIG_CMDLINE.
2347 Systems with fully functional boot loaders (i.e. non-embedded)
2348 should leave this option set to 'N'.
2351 string "Built-in kernel command string"
2352 depends on CMDLINE_BOOL
2355 Enter arguments here that should be compiled into the kernel
2356 image and used at boot time. If the boot loader provides a
2357 command line at boot time, it is appended to this string to
2358 form the full kernel command line, when the system boots.
2360 However, you can use the CONFIG_CMDLINE_OVERRIDE option to
2361 change this behavior.
2363 In most cases, the command line (whether built-in or provided
2364 by the boot loader) should specify the device for the root
2367 config CMDLINE_OVERRIDE
2368 bool "Built-in command line overrides boot loader arguments"
2369 depends on CMDLINE_BOOL
2371 Set this option to 'Y' to have the kernel ignore the boot loader
2372 command line, and use ONLY the built-in command line.
2374 This is used to work around broken boot loaders. This should
2375 be set to 'N' under normal conditions.
2377 config MODIFY_LDT_SYSCALL
2378 bool "Enable the LDT (local descriptor table)" if EXPERT
2381 Linux can allow user programs to install a per-process x86
2382 Local Descriptor Table (LDT) using the modify_ldt(2) system
2383 call. This is required to run 16-bit or segmented code such as
2384 DOSEMU or some Wine programs. It is also used by some very old
2385 threading libraries.
2387 Enabling this feature adds a small amount of overhead to
2388 context switches and increases the low-level kernel attack
2389 surface. Disabling it removes the modify_ldt(2) system call.
2391 Saying 'N' here may make sense for embedded or server kernels.
2393 source "kernel/livepatch/Kconfig"
2397 config ARCH_HAS_ADD_PAGES
2399 depends on X86_64 && ARCH_ENABLE_MEMORY_HOTPLUG
2401 config ARCH_ENABLE_MEMORY_HOTPLUG
2403 depends on X86_64 || (X86_32 && HIGHMEM)
2405 config ARCH_ENABLE_MEMORY_HOTREMOVE
2407 depends on MEMORY_HOTPLUG
2409 config USE_PERCPU_NUMA_NODE_ID
2413 config ARCH_ENABLE_SPLIT_PMD_PTLOCK
2415 depends on X86_64 || X86_PAE
2417 config ARCH_ENABLE_HUGEPAGE_MIGRATION
2419 depends on X86_64 && HUGETLB_PAGE && MIGRATION
2421 config ARCH_ENABLE_THP_MIGRATION
2423 depends on X86_64 && TRANSPARENT_HUGEPAGE
2425 menu "Power management and ACPI options"
2427 config ARCH_HIBERNATION_HEADER
2429 depends on X86_64 && HIBERNATION
2431 source "kernel/power/Kconfig"
2433 source "drivers/acpi/Kconfig"
2435 source "drivers/sfi/Kconfig"
2442 tristate "APM (Advanced Power Management) BIOS support"
2443 depends on X86_32 && PM_SLEEP
2445 APM is a BIOS specification for saving power using several different
2446 techniques. This is mostly useful for battery powered laptops with
2447 APM compliant BIOSes. If you say Y here, the system time will be
2448 reset after a RESUME operation, the /proc/apm device will provide
2449 battery status information, and user-space programs will receive
2450 notification of APM "events" (e.g. battery status change).
2452 If you select "Y" here, you can disable actual use of the APM
2453 BIOS by passing the "apm=off" option to the kernel at boot time.
2455 Note that the APM support is almost completely disabled for
2456 machines with more than one CPU.
2458 In order to use APM, you will need supporting software. For location
2459 and more information, read <file:Documentation/power/apm-acpi.txt>
2460 and the Battery Powered Linux mini-HOWTO, available from
2461 <http://www.tldp.org/docs.html#howto>.
2463 This driver does not spin down disk drives (see the hdparm(8)
2464 manpage ("man 8 hdparm") for that), and it doesn't turn off
2465 VESA-compliant "green" monitors.
2467 This driver does not support the TI 4000M TravelMate and the ACER
2468 486/DX4/75 because they don't have compliant BIOSes. Many "green"
2469 desktop machines also don't have compliant BIOSes, and this driver
2470 may cause those machines to panic during the boot phase.
2472 Generally, if you don't have a battery in your machine, there isn't
2473 much point in using this driver and you should say N. If you get
2474 random kernel OOPSes or reboots that don't seem to be related to
2475 anything, try disabling/enabling this option (or disabling/enabling
2478 Some other things you should try when experiencing seemingly random,
2481 1) make sure that you have enough swap space and that it is
2483 2) pass the "no-hlt" option to the kernel
2484 3) switch on floating point emulation in the kernel and pass
2485 the "no387" option to the kernel
2486 4) pass the "floppy=nodma" option to the kernel
2487 5) pass the "mem=4M" option to the kernel (thereby disabling
2488 all but the first 4 MB of RAM)
2489 6) make sure that the CPU is not over clocked.
2490 7) read the sig11 FAQ at <http://www.bitwizard.nl/sig11/>
2491 8) disable the cache from your BIOS settings
2492 9) install a fan for the video card or exchange video RAM
2493 10) install a better fan for the CPU
2494 11) exchange RAM chips
2495 12) exchange the motherboard.
2497 To compile this driver as a module, choose M here: the
2498 module will be called apm.
2502 config APM_IGNORE_USER_SUSPEND
2503 bool "Ignore USER SUSPEND"
2505 This option will ignore USER SUSPEND requests. On machines with a
2506 compliant APM BIOS, you want to say N. However, on the NEC Versa M
2507 series notebooks, it is necessary to say Y because of a BIOS bug.
2509 config APM_DO_ENABLE
2510 bool "Enable PM at boot time"
2512 Enable APM features at boot time. From page 36 of the APM BIOS
2513 specification: "When disabled, the APM BIOS does not automatically
2514 power manage devices, enter the Standby State, enter the Suspend
2515 State, or take power saving steps in response to CPU Idle calls."
2516 This driver will make CPU Idle calls when Linux is idle (unless this
2517 feature is turned off -- see "Do CPU IDLE calls", below). This
2518 should always save battery power, but more complicated APM features
2519 will be dependent on your BIOS implementation. You may need to turn
2520 this option off if your computer hangs at boot time when using APM
2521 support, or if it beeps continuously instead of suspending. Turn
2522 this off if you have a NEC UltraLite Versa 33/C or a Toshiba
2523 T400CDT. This is off by default since most machines do fine without
2528 bool "Make CPU Idle calls when idle"
2530 Enable calls to APM CPU Idle/CPU Busy inside the kernel's idle loop.
2531 On some machines, this can activate improved power savings, such as
2532 a slowed CPU clock rate, when the machine is idle. These idle calls
2533 are made after the idle loop has run for some length of time (e.g.,
2534 333 mS). On some machines, this will cause a hang at boot time or
2535 whenever the CPU becomes idle. (On machines with more than one CPU,
2536 this option does nothing.)
2538 config APM_DISPLAY_BLANK
2539 bool "Enable console blanking using APM"
2541 Enable console blanking using the APM. Some laptops can use this to
2542 turn off the LCD backlight when the screen blanker of the Linux
2543 virtual console blanks the screen. Note that this is only used by
2544 the virtual console screen blanker, and won't turn off the backlight
2545 when using the X Window system. This also doesn't have anything to
2546 do with your VESA-compliant power-saving monitor. Further, this
2547 option doesn't work for all laptops -- it might not turn off your
2548 backlight at all, or it might print a lot of errors to the console,
2549 especially if you are using gpm.
2551 config APM_ALLOW_INTS
2552 bool "Allow interrupts during APM BIOS calls"
2554 Normally we disable external interrupts while we are making calls to
2555 the APM BIOS as a measure to lessen the effects of a badly behaving
2556 BIOS implementation. The BIOS should reenable interrupts if it
2557 needs to. Unfortunately, some BIOSes do not -- especially those in
2558 many of the newer IBM Thinkpads. If you experience hangs when you
2559 suspend, try setting this to Y. Otherwise, say N.
2563 source "drivers/cpufreq/Kconfig"
2565 source "drivers/cpuidle/Kconfig"
2567 source "drivers/idle/Kconfig"
2572 menu "Bus options (PCI etc.)"
2578 Find out whether you have a PCI motherboard. PCI is the name of a
2579 bus system, i.e. the way the CPU talks to the other stuff inside
2580 your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
2581 VESA. If you have PCI, say Y, otherwise N.
2584 prompt "PCI access mode"
2585 depends on X86_32 && PCI
2588 On PCI systems, the BIOS can be used to detect the PCI devices and
2589 determine their configuration. However, some old PCI motherboards
2590 have BIOS bugs and may crash if this is done. Also, some embedded
2591 PCI-based systems don't have any BIOS at all. Linux can also try to
2592 detect the PCI hardware directly without using the BIOS.
2594 With this option, you can specify how Linux should detect the
2595 PCI devices. If you choose "BIOS", the BIOS will be used,
2596 if you choose "Direct", the BIOS won't be used, and if you
2597 choose "MMConfig", then PCI Express MMCONFIG will be used.
2598 If you choose "Any", the kernel will try MMCONFIG, then the
2599 direct access method and falls back to the BIOS if that doesn't
2600 work. If unsure, go with the default, which is "Any".
2605 config PCI_GOMMCONFIG
2622 depends on X86_32 && PCI && (PCI_GOBIOS || PCI_GOANY)
2624 # x86-64 doesn't support PCI BIOS access from long mode so always go direct.
2627 depends on PCI && (X86_64 || (PCI_GODIRECT || PCI_GOANY || PCI_GOOLPC || PCI_GOMMCONFIG))
2630 bool "Support mmconfig PCI config space access" if X86_64
2632 depends on PCI && (ACPI || SFI || JAILHOUSE_GUEST)
2633 depends on X86_64 || (PCI_GOANY || PCI_GOMMCONFIG)
2637 depends on PCI && OLPC && (PCI_GOOLPC || PCI_GOANY)
2641 depends on PCI && XEN
2648 config MMCONF_FAM10H
2650 depends on X86_64 && PCI_MMCONFIG && ACPI
2652 config PCI_CNB20LE_QUIRK
2653 bool "Read CNB20LE Host Bridge Windows" if EXPERT
2656 Read the PCI windows out of the CNB20LE host bridge. This allows
2657 PCI hotplug to work on systems with the CNB20LE chipset which do
2660 There's no public spec for this chipset, and this functionality
2661 is known to be incomplete.
2663 You should say N unless you know you need this.
2665 source "drivers/pci/Kconfig"
2668 bool "ISA bus support on modern systems" if EXPERT
2670 Expose ISA bus device drivers and options available for selection and
2671 configuration. Enable this option if your target machine has an ISA
2672 bus. ISA is an older system, displaced by PCI and newer bus
2673 architectures -- if your target machine is modern, it probably does
2674 not have an ISA bus.
2678 # x86_64 have no ISA slots, but can have ISA-style DMA.
2680 bool "ISA-style DMA support" if (X86_64 && EXPERT)
2683 Enables ISA-style DMA support for devices requiring such controllers.
2691 Find out whether you have ISA slots on your motherboard. ISA is the
2692 name of a bus system, i.e. the way the CPU talks to the other stuff
2693 inside your box. Other bus systems are PCI, EISA, MicroChannel
2694 (MCA) or VESA. ISA is an older system, now being displaced by PCI;
2695 newer boards don't support it. If you have ISA, say Y, otherwise N.
2701 The Extended Industry Standard Architecture (EISA) bus was
2702 developed as an open alternative to the IBM MicroChannel bus.
2704 The EISA bus provided some of the features of the IBM MicroChannel
2705 bus while maintaining backward compatibility with cards made for
2706 the older ISA bus. The EISA bus saw limited use between 1988 and
2707 1995 when it was made obsolete by the PCI bus.
2709 Say Y here if you are building a kernel for an EISA-based machine.
2713 source "drivers/eisa/Kconfig"
2716 tristate "NatSemi SCx200 support"
2718 This provides basic support for National Semiconductor's
2719 (now AMD's) Geode processors. The driver probes for the
2720 PCI-IDs of several on-chip devices, so its a good dependency
2721 for other scx200_* drivers.
2723 If compiled as a module, the driver is named scx200.
2725 config SCx200HR_TIMER
2726 tristate "NatSemi SCx200 27MHz High-Resolution Timer Support"
2730 This driver provides a clocksource built upon the on-chip
2731 27MHz high-resolution timer. Its also a workaround for
2732 NSC Geode SC-1100's buggy TSC, which loses time when the
2733 processor goes idle (as is done by the scheduler). The
2734 other workaround is idle=poll boot option.
2737 bool "One Laptop Per Child support"
2744 Add support for detecting the unique features of the OLPC
2748 bool "OLPC XO-1 Power Management"
2749 depends on OLPC && MFD_CS5535 && PM_SLEEP
2752 Add support for poweroff and suspend of the OLPC XO-1 laptop.
2755 bool "OLPC XO-1 Real Time Clock"
2756 depends on OLPC_XO1_PM && RTC_DRV_CMOS
2758 Add support for the XO-1 real time clock, which can be used as a
2759 programmable wakeup source.
2762 bool "OLPC XO-1 SCI extras"
2763 depends on OLPC && OLPC_XO1_PM && GPIO_CS5535=y
2767 Add support for SCI-based features of the OLPC XO-1 laptop:
2768 - EC-driven system wakeups
2772 - AC adapter status updates
2773 - Battery status updates
2775 config OLPC_XO15_SCI
2776 bool "OLPC XO-1.5 SCI extras"
2777 depends on OLPC && ACPI
2780 Add support for SCI-based features of the OLPC XO-1.5 laptop:
2781 - EC-driven system wakeups
2782 - AC adapter status updates
2783 - Battery status updates
2786 bool "PCEngines ALIX System Support (LED setup)"
2789 This option enables system support for the PCEngines ALIX.
2790 At present this just sets up LEDs for GPIO control on
2791 ALIX2/3/6 boards. However, other system specific setup should
2794 Note: You must still enable the drivers for GPIO and LED support
2795 (GPIO_CS5535 & LEDS_GPIO) to actually use the LEDs
2797 Note: You have to set alix.force=1 for boards with Award BIOS.
2800 bool "Soekris Engineering net5501 System Support (LEDS, GPIO, etc)"
2803 This option enables system support for the Soekris Engineering net5501.
2806 bool "Traverse Technologies GEOS System Support (LEDS, GPIO, etc)"
2810 This option enables system support for the Traverse Technologies GEOS.
2813 bool "Technologic Systems TS-5500 platform support"
2815 select CHECK_SIGNATURE
2819 This option enables system support for the Technologic Systems TS-5500.
2825 depends on CPU_SUP_AMD && PCI
2827 source "drivers/pcmcia/Kconfig"
2830 tristate "RapidIO support"
2834 If enabled this option will include drivers and the core
2835 infrastructure code to support RapidIO interconnect devices.
2837 source "drivers/rapidio/Kconfig"
2840 bool "Mark VGA/VBE/EFI FB as generic system framebuffer"
2842 Firmwares often provide initial graphics framebuffers so the BIOS,
2843 bootloader or kernel can show basic video-output during boot for
2844 user-guidance and debugging. Historically, x86 used the VESA BIOS
2845 Extensions and EFI-framebuffers for this, which are mostly limited
2847 This option, if enabled, marks VGA/VBE/EFI framebuffers as generic
2848 framebuffers so the new generic system-framebuffer drivers can be
2849 used on x86. If the framebuffer is not compatible with the generic
2850 modes, it is adverticed as fallback platform framebuffer so legacy
2851 drivers like efifb, vesafb and uvesafb can pick it up.
2852 If this option is not selected, all system framebuffers are always
2853 marked as fallback platform framebuffers as usual.
2855 Note: Legacy fbdev drivers, including vesafb, efifb, uvesafb, will
2856 not be able to pick up generic system framebuffers if this option
2857 is selected. You are highly encouraged to enable simplefb as
2858 replacement if you select this option. simplefb can correctly deal
2859 with generic system framebuffers. But you should still keep vesafb
2860 and others enabled as fallback if a system framebuffer is
2861 incompatible with simplefb.
2868 menu "Executable file formats / Emulations"
2870 source "fs/Kconfig.binfmt"
2872 config IA32_EMULATION
2873 bool "IA32 Emulation"
2875 select ARCH_WANT_OLD_COMPAT_IPC
2877 select COMPAT_BINFMT_ELF
2878 select COMPAT_OLD_SIGACTION
2880 Include code to run legacy 32-bit programs under a
2881 64-bit kernel. You should likely turn this on, unless you're
2882 100% sure that you don't have any 32-bit programs left.
2885 tristate "IA32 a.out support"
2886 depends on IA32_EMULATION
2888 Support old a.out binaries in the 32bit emulation.
2891 bool "x32 ABI for 64-bit mode"
2894 Include code to run binaries for the x32 native 32-bit ABI
2895 for 64-bit processors. An x32 process gets access to the
2896 full 64-bit register file and wide data path while leaving
2897 pointers at 32 bits for smaller memory footprint.
2899 You will need a recent binutils (2.22 or later) with
2900 elf32_x86_64 support enabled to compile a kernel with this
2905 depends on IA32_EMULATION || X86_32
2907 select OLD_SIGSUSPEND3
2911 depends on IA32_EMULATION || X86_X32
2914 config COMPAT_FOR_U64_ALIGNMENT
2917 config SYSVIPC_COMPAT
2925 config HAVE_ATOMIC_IOMAP
2929 config X86_DEV_DMA_OPS
2931 depends on X86_64 || STA2X11
2933 config X86_DMA_REMAP
2937 config HAVE_GENERIC_GUP
2940 source "net/Kconfig"
2942 source "drivers/Kconfig"
2944 source "drivers/firmware/Kconfig"
2948 source "arch/x86/Kconfig.debug"
2950 source "security/Kconfig"
2952 source "crypto/Kconfig"
2954 source "arch/x86/kvm/Kconfig"
2956 source "lib/Kconfig"