1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * Copyright 2010-2011, 2013 Freescale Semiconductor, Inc.
5 * Author: Michael Johnston <michael.johnston@freescale.com>
8 * TWR-P102x Board Setup
11 #include <linux/kernel.h>
12 #include <linux/init.h>
13 #include <linux/errno.h>
14 #include <linux/fsl/guts.h>
15 #include <linux/pci.h>
16 #include <linux/of_platform.h>
18 #include <asm/pci-bridge.h>
21 #include <soc/fsl/qe/qe.h>
22 #include <soc/fsl/qe/qe_ic.h>
24 #include <sysdev/fsl_soc.h>
25 #include <sysdev/fsl_pci.h>
30 static void __init twr_p1025_pic_init(void)
34 #ifdef CONFIG_QUICC_ENGINE
35 struct device_node *np;
38 mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
45 #ifdef CONFIG_QUICC_ENGINE
46 np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic");
48 qe_ic_init(np, 0, qe_ic_cascade_low_mpic,
49 qe_ic_cascade_high_mpic);
52 pr_err("Could not find qe-ic node\n");
56 /* ************************************************************************
58 * Setup the architecture
61 static void __init twr_p1025_setup_arch(void)
63 #ifdef CONFIG_QUICC_ENGINE
64 struct device_node *np;
68 ppc_md.progress("twr_p1025_setup_arch()", 0);
72 fsl_pci_assign_primary();
74 #ifdef CONFIG_QUICC_ENGINE
76 mpc85xx_qe_par_io_init();
78 #if IS_ENABLED(CONFIG_UCC_GETH) || IS_ENABLED(CONFIG_SERIAL_QE)
79 if (machine_is(twr_p1025)) {
80 struct ccsr_guts __iomem *guts;
82 np = of_find_compatible_node(NULL, NULL, "fsl,p1021-guts");
84 guts = of_iomap(np, 0);
86 pr_err("twr_p1025: could not map global utilities register\n");
88 /* P1025 has pins muxed for QE and other functions. To
89 * enable QE UEC mode, we need to set bit QE0 for UCC1
90 * in Eth mode, QE0 and QE3 for UCC5 in Eth mode, QE9
91 * and QE12 for QE MII management signals in PMUXCR
93 * Set QE mux bits in PMUXCR */
94 setbits32(&guts->pmuxcr, MPC85xx_PMUXCR_QE(0) |
95 MPC85xx_PMUXCR_QE(3) |
96 MPC85xx_PMUXCR_QE(9) |
97 MPC85xx_PMUXCR_QE(12));
100 #if IS_ENABLED(CONFIG_SERIAL_QE)
101 /* On P1025TWR board, the UCC7 acted as UART port.
102 * However, The UCC7's CTS pin is low level in default,
103 * it will impact the transmission in full duplex
104 * communication. So disable the Flow control pin PA18.
105 * The UCC7 UART just can use RXD and TXD pins.
107 par_io_config_pin(0, 18, 0, 0, 0, 0);
109 /* Drive PB29 to CPLD low - CPLD will then change
110 * muxing from LBC to QE */
111 par_io_config_pin(1, 29, 1, 0, 0, 0);
112 par_io_data_set(1, 29, 0);
118 #endif /* CONFIG_QUICC_ENGINE */
120 pr_info("TWR-P1025 board from Freescale Semiconductor\n");
123 machine_arch_initcall(twr_p1025, mpc85xx_common_publish_devices);
125 static int __init twr_p1025_probe(void)
127 return of_machine_is_compatible("fsl,TWR-P1025");
130 define_machine(twr_p1025) {
132 .probe = twr_p1025_probe,
133 .setup_arch = twr_p1025_setup_arch,
134 .init_IRQ = twr_p1025_pic_init,
136 .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
138 .get_irq = mpic_get_irq,
139 .calibrate_decr = generic_calibrate_decr,
140 .progress = udbg_progress,