2 * arch/arm/mach-orion5x/edmini_v2-setup.c
4 * LaCie Ethernet Disk mini V2 Setup
6 * Copyright (C) 2008 Christopher Moore <moore@free.fr>
7 * Copyright (C) 2008 Albert Aribaud <albert.aribaud@free.fr>
9 * This file is licensed under the terms of the GNU General Public
10 * License version 2. This program is licensed "as is" without any
11 * warranty of any kind, whether express or implied.
15 * TODO: add Orion USB device port init when kernel.org support is added.
16 * TODO: add flash write support: see below.
17 * TODO: add power-off support.
18 * TODO: add I2C EEPROM support.
21 #include <linux/kernel.h>
22 #include <linux/init.h>
23 #include <linux/platform_device.h>
24 #include <linux/pci.h>
25 #include <linux/irq.h>
26 #include <linux/mtd/physmap.h>
27 #include <linux/mv643xx_eth.h>
28 #include <linux/leds.h>
29 #include <linux/gpio_keys.h>
30 #include <linux/input.h>
31 #include <linux/i2c.h>
32 #include <linux/ata_platform.h>
33 #include <linux/gpio.h>
34 #include <asm/mach-types.h>
35 #include <asm/mach/arch.h>
36 #include <asm/mach/pci.h>
37 #include <mach/orion5x.h>
41 /*****************************************************************************
43 ****************************************************************************/
46 * 512KB NOR flash Device bus boot chip select
49 #define EDMINI_V2_NOR_BOOT_BASE 0xfff80000
50 #define EDMINI_V2_NOR_BOOT_SIZE SZ_512K
52 /*****************************************************************************
53 * 512KB NOR Flash on BOOT Device
54 ****************************************************************************/
57 * Currently the MTD code does not recognize the MX29LV400CBCT as a bottom
58 * -type device. This could cause risks of accidentally erasing critical
59 * flash sectors. We thus define a single, write-protected partition covering
61 * TODO: once the flash part TOP/BOTTOM detection issue is sorted out in the MTD
62 * code, break this into at least three partitions: 'u-boot code', 'u-boot
63 * environment' and 'whatever is left'.
66 static struct mtd_partition edmini_v2_partitions[] = {
71 .mask_flags = MTD_WRITEABLE,
75 static struct physmap_flash_data edmini_v2_nor_flash_data = {
77 .parts = edmini_v2_partitions,
78 .nr_parts = ARRAY_SIZE(edmini_v2_partitions),
81 static struct resource edmini_v2_nor_flash_resource = {
82 .flags = IORESOURCE_MEM,
83 .start = EDMINI_V2_NOR_BOOT_BASE,
84 .end = EDMINI_V2_NOR_BOOT_BASE
85 + EDMINI_V2_NOR_BOOT_SIZE - 1,
88 static struct platform_device edmini_v2_nor_flash = {
89 .name = "physmap-flash",
92 .platform_data = &edmini_v2_nor_flash_data,
95 .resource = &edmini_v2_nor_flash_resource,
98 /*****************************************************************************
100 ****************************************************************************/
102 static struct mv643xx_eth_platform_data edmini_v2_eth_data = {
106 /*****************************************************************************
107 * RTC 5C372a on I2C bus
108 ****************************************************************************/
110 #define EDMINIV2_RTC_GPIO 3
112 static struct i2c_board_info __initdata edmini_v2_i2c_rtc = {
113 I2C_BOARD_INFO("rs5c372a", 0x32),
117 /*****************************************************************************
119 ****************************************************************************/
120 static unsigned int edminiv2_mpp_modes[] __initdata = {
124 MPP3_GPIO, /* RTC interrupt */
133 MPP12_SATA_LED, /* SATA 0 presence */
134 MPP13_SATA_LED, /* SATA 1 presence */
135 MPP14_SATA_LED, /* SATA 0 active */
136 MPP15_SATA_LED, /* SATA 1 active */
137 /* 16: Power LED control (0 = On, 1 = Off) */
139 /* 17: Power LED control select (0 = CPLD, 1 = GPIO16) */
141 /* 18: Power button status (0 = Released, 1 = Pressed) */
147 void __init edmini_v2_init(void)
149 orion5x_mpp_conf(edminiv2_mpp_modes);
152 * Configure peripherals.
154 orion5x_ehci0_init();
155 orion5x_eth_init(&edmini_v2_eth_data);
157 orion5x_setup_dev_boot_win(EDMINI_V2_NOR_BOOT_BASE,
158 EDMINI_V2_NOR_BOOT_SIZE);
159 platform_device_register(&edmini_v2_nor_flash);
161 pr_notice("edmini_v2: USB device port, flash write and power-off "
162 "are not yet supported.\n");
164 /* Get RTC IRQ and register the chip */
165 if (gpio_request(EDMINIV2_RTC_GPIO, "rtc") == 0) {
166 if (gpio_direction_input(EDMINIV2_RTC_GPIO) == 0)
167 edmini_v2_i2c_rtc.irq = gpio_to_irq(EDMINIV2_RTC_GPIO);
169 gpio_free(EDMINIV2_RTC_GPIO);
172 if (edmini_v2_i2c_rtc.irq == 0)
173 pr_warning("edmini_v2: failed to get RTC IRQ\n");
175 i2c_register_board_info(0, &edmini_v2_i2c_rtc, 1);