2 * linux/arch/arm/mach-omap2/board-omap3evm.c
4 * Copyright (C) 2008 Texas Instruments
6 * Modified from mach-omap2/board-3430sdp.c
8 * Initial code: Syed Mohammed Khasim
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License version 2 as
12 * published by the Free Software Foundation.
15 #include <linux/kernel.h>
16 #include <linux/init.h>
17 #include <linux/platform_device.h>
18 #include <linux/delay.h>
19 #include <linux/err.h>
20 #include <linux/clk.h>
21 #include <linux/gpio.h>
22 #include <linux/input.h>
23 #include <linux/input/matrix_keypad.h>
24 #include <linux/leds.h>
25 #include <linux/interrupt.h>
27 #include <linux/mtd/mtd.h>
28 #include <linux/mtd/partitions.h>
29 #include <linux/mtd/nand.h>
31 #include <linux/spi/spi.h>
32 #include <linux/spi/ads7846.h>
33 #include <linux/i2c/twl.h>
34 #include <linux/usb/otg.h>
35 #include <linux/usb/musb.h>
36 #include <linux/usb/nop-usb-xceiv.h>
37 #include <linux/smsc911x.h>
39 #include <linux/wl12xx.h>
40 #include <linux/regulator/fixed.h>
41 #include <linux/regulator/machine.h>
42 #include <linux/mmc/host.h>
43 #include <linux/export.h>
44 #include <linux/usb/phy.h>
46 #include <asm/mach-types.h>
47 #include <asm/mach/arch.h>
48 #include <asm/mach/map.h>
50 #include <linux/platform_data/mtd-nand-omap2.h>
52 #include <linux/platform_data/spi-omap2-mcspi.h>
53 #include <video/omapdss.h>
54 #include <video/omap-panel-tfp410.h>
58 #include "sdram-micron-mt46h32m32lf-6.h"
60 #include "common-board-devices.h"
61 #include "board-flash.h"
65 #define OMAP3_EVM_TS_GPIO 175
66 #define OMAP3_EVM_EHCI_VBUS 22
67 #define OMAP3_EVM_EHCI_SELECT 61
69 #define OMAP3EVM_ETHR_START 0x2c000000
70 #define OMAP3EVM_ETHR_SIZE 1024
71 #define OMAP3EVM_ETHR_ID_REV 0x50
72 #define OMAP3EVM_ETHR_GPIO_IRQ 176
73 #define OMAP3EVM_SMSC911X_CS 5
76 * 64 = Generation 1 (<=RevD)
77 * 7 = Generation 2 (>=RevE)
79 #define OMAP3EVM_GEN1_ETHR_GPIO_RST 64
80 #define OMAP3EVM_GEN2_ETHR_GPIO_RST 7
83 * OMAP35x EVM revision
84 * Run time detection of EVM revision is done by reading Ethernet
90 OMAP3EVM_BOARD_GEN_1 = 0, /* EVM Rev between A - D */
91 OMAP3EVM_BOARD_GEN_2, /* EVM Rev >= Rev E */
94 static u8 omap3_evm_version;
96 static u8 get_omap3_evm_rev(void)
98 return omap3_evm_version;
101 static void __init omap3_evm_get_revision(void)
103 void __iomem *ioaddr;
104 unsigned int smsc_id;
106 /* Ethernet PHY ID is stored at ID_REV register */
107 ioaddr = ioremap_nocache(OMAP3EVM_ETHR_START, SZ_1K);
110 smsc_id = readl(ioaddr + OMAP3EVM_ETHR_ID_REV) & 0xFFFF0000;
116 omap3_evm_version = OMAP3EVM_BOARD_GEN_1;
118 /*SMSC 9220 chipset*/
121 omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
125 #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
126 #include "gpmc-smsc911x.h"
128 static struct omap_smsc911x_platform_data smsc911x_cfg = {
129 .cs = OMAP3EVM_SMSC911X_CS,
130 .gpio_irq = OMAP3EVM_ETHR_GPIO_IRQ,
131 .gpio_reset = -EINVAL,
132 .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
135 static inline void __init omap3evm_init_smsc911x(void)
137 /* Configure ethernet controller reset gpio */
138 if (cpu_is_omap3430()) {
139 if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1)
140 smsc911x_cfg.gpio_reset = OMAP3EVM_GEN1_ETHR_GPIO_RST;
142 smsc911x_cfg.gpio_reset = OMAP3EVM_GEN2_ETHR_GPIO_RST;
145 gpmc_smsc911x_init(&smsc911x_cfg);
149 static inline void __init omap3evm_init_smsc911x(void) { return; }
153 * OMAP3EVM LCD Panel control signals
155 #define OMAP3EVM_LCD_PANEL_LR 2
156 #define OMAP3EVM_LCD_PANEL_UD 3
157 #define OMAP3EVM_LCD_PANEL_INI 152
158 #define OMAP3EVM_LCD_PANEL_ENVDD 153
159 #define OMAP3EVM_LCD_PANEL_QVGA 154
160 #define OMAP3EVM_LCD_PANEL_RESB 155
161 #define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO 210
162 #define OMAP3EVM_DVI_PANEL_EN_GPIO 199
164 static struct gpio omap3_evm_dss_gpios[] __initdata = {
165 { OMAP3EVM_LCD_PANEL_RESB, GPIOF_OUT_INIT_HIGH, "lcd_panel_resb" },
166 { OMAP3EVM_LCD_PANEL_INI, GPIOF_OUT_INIT_HIGH, "lcd_panel_ini" },
167 { OMAP3EVM_LCD_PANEL_QVGA, GPIOF_OUT_INIT_LOW, "lcd_panel_qvga" },
168 { OMAP3EVM_LCD_PANEL_LR, GPIOF_OUT_INIT_HIGH, "lcd_panel_lr" },
169 { OMAP3EVM_LCD_PANEL_UD, GPIOF_OUT_INIT_HIGH, "lcd_panel_ud" },
170 { OMAP3EVM_LCD_PANEL_ENVDD, GPIOF_OUT_INIT_LOW, "lcd_panel_envdd" },
173 static int lcd_enabled;
174 static int dvi_enabled;
176 static void __init omap3_evm_display_init(void)
180 r = gpio_request_array(omap3_evm_dss_gpios,
181 ARRAY_SIZE(omap3_evm_dss_gpios));
183 printk(KERN_ERR "failed to get lcd_panel_* gpios\n");
186 static int omap3_evm_enable_lcd(struct omap_dss_device *dssdev)
189 printk(KERN_ERR "cannot enable LCD, DVI is enabled\n");
192 gpio_set_value(OMAP3EVM_LCD_PANEL_ENVDD, 0);
194 if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
195 gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0);
197 gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1);
203 static void omap3_evm_disable_lcd(struct omap_dss_device *dssdev)
205 gpio_set_value(OMAP3EVM_LCD_PANEL_ENVDD, 1);
207 if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
208 gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1);
210 gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0);
215 static struct omap_dss_device omap3_evm_lcd_device = {
217 .driver_name = "sharp_ls_panel",
218 .type = OMAP_DISPLAY_TYPE_DPI,
219 .phy.dpi.data_lines = 18,
220 .platform_enable = omap3_evm_enable_lcd,
221 .platform_disable = omap3_evm_disable_lcd,
224 static int omap3_evm_enable_tv(struct omap_dss_device *dssdev)
229 static void omap3_evm_disable_tv(struct omap_dss_device *dssdev)
233 static struct omap_dss_device omap3_evm_tv_device = {
235 .driver_name = "venc",
236 .type = OMAP_DISPLAY_TYPE_VENC,
237 .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
238 .platform_enable = omap3_evm_enable_tv,
239 .platform_disable = omap3_evm_disable_tv,
242 static struct tfp410_platform_data dvi_panel = {
243 .power_down_gpio = OMAP3EVM_DVI_PANEL_EN_GPIO,
247 static struct omap_dss_device omap3_evm_dvi_device = {
249 .type = OMAP_DISPLAY_TYPE_DPI,
250 .driver_name = "tfp410",
252 .phy.dpi.data_lines = 24,
255 static struct omap_dss_device *omap3_evm_dss_devices[] = {
256 &omap3_evm_lcd_device,
257 &omap3_evm_tv_device,
258 &omap3_evm_dvi_device,
261 static struct omap_dss_board_info omap3_evm_dss_data = {
262 .num_devices = ARRAY_SIZE(omap3_evm_dss_devices),
263 .devices = omap3_evm_dss_devices,
264 .default_device = &omap3_evm_lcd_device,
267 static struct regulator_consumer_supply omap3evm_vmmc1_supply[] = {
268 REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
271 static struct regulator_consumer_supply omap3evm_vsim_supply[] = {
272 REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
275 /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
276 static struct regulator_init_data omap3evm_vmmc1 = {
280 .valid_modes_mask = REGULATOR_MODE_NORMAL
281 | REGULATOR_MODE_STANDBY,
282 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
283 | REGULATOR_CHANGE_MODE
284 | REGULATOR_CHANGE_STATUS,
286 .num_consumer_supplies = ARRAY_SIZE(omap3evm_vmmc1_supply),
287 .consumer_supplies = omap3evm_vmmc1_supply,
290 /* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
291 static struct regulator_init_data omap3evm_vsim = {
295 .valid_modes_mask = REGULATOR_MODE_NORMAL
296 | REGULATOR_MODE_STANDBY,
297 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
298 | REGULATOR_CHANGE_MODE
299 | REGULATOR_CHANGE_STATUS,
301 .num_consumer_supplies = ARRAY_SIZE(omap3evm_vsim_supply),
302 .consumer_supplies = omap3evm_vsim_supply,
305 static struct omap2_hsmmc_info mmc[] = {
308 .caps = MMC_CAP_4_BIT_DATA,
313 #ifdef CONFIG_WILINK_PLATFORM_DATA
317 .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
320 .nonremovable = true,
326 static struct gpio_led gpio_leds[] = {
328 .name = "omap3evm::ledb",
329 /* normally not visible (board underside) */
330 .default_trigger = "default-on",
331 .gpio = -EINVAL, /* gets replaced */
336 static struct gpio_led_platform_data gpio_led_info = {
338 .num_leds = ARRAY_SIZE(gpio_leds),
341 static struct platform_device leds_gpio = {
345 .platform_data = &gpio_led_info,
350 static int omap3evm_twl_gpio_setup(struct device *dev,
351 unsigned gpio, unsigned ngpio)
355 /* gpio + 0 is "mmc0_cd" (input/IRQ) */
356 mmc[0].gpio_cd = gpio + 0;
357 omap_hsmmc_late_init(mmc);
360 * Most GPIOs are for USB OTG. Some are mostly sent to
361 * the P2 connector; notably LEDA for the LCD backlight.
364 /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
365 lcd_bl_en = get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2 ?
366 GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
367 r = gpio_request_one(gpio + TWL4030_GPIO_MAX, lcd_bl_en, "EN_LCD_BKL");
369 printk(KERN_ERR "failed to get/set lcd_bkl gpio\n");
371 /* gpio + 7 == DVI Enable */
372 gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
374 /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
375 gpio_leds[0].gpio = gpio + TWL4030_GPIO_MAX + 1;
377 platform_device_register(&leds_gpio);
379 /* Enable VBUS switch by setting TWL4030.GPIO2DIR as output
380 * for starting USB tranceiver
382 #ifdef CONFIG_TWL4030_CORE
383 if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
386 twl_i2c_read_u8(TWL4030_MODULE_GPIO, &val, REG_GPIODATADIR1);
387 val |= 0x04; /* TWL4030.GPIO2DIR BIT at GPIODATADIR1(0x9B) */
388 twl_i2c_write_u8(TWL4030_MODULE_GPIO, val, REG_GPIODATADIR1);
395 static struct twl4030_gpio_platform_data omap3evm_gpio_data = {
397 .setup = omap3evm_twl_gpio_setup,
400 static uint32_t board_keymap[] = {
403 KEY(0, 2, KEY_ENTER),
406 KEY(1, 0, KEY_RIGHT),
422 static struct matrix_keymap_data board_map_data = {
423 .keymap = board_keymap,
424 .keymap_size = ARRAY_SIZE(board_keymap),
427 static struct twl4030_keypad_data omap3evm_kp_data = {
428 .keymap_data = &board_map_data,
435 static struct regulator_consumer_supply omap3evm_vio_supply[] = {
436 REGULATOR_SUPPLY("vcc", "spi1.0"),
439 /* VIO for ads7846 */
440 static struct regulator_init_data omap3evm_vio = {
445 .valid_modes_mask = REGULATOR_MODE_NORMAL
446 | REGULATOR_MODE_STANDBY,
447 .valid_ops_mask = REGULATOR_CHANGE_MODE
448 | REGULATOR_CHANGE_STATUS,
450 .num_consumer_supplies = ARRAY_SIZE(omap3evm_vio_supply),
451 .consumer_supplies = omap3evm_vio_supply,
454 #ifdef CONFIG_WILINK_PLATFORM_DATA
456 #define OMAP3EVM_WLAN_PMENA_GPIO (150)
457 #define OMAP3EVM_WLAN_IRQ_GPIO (149)
459 static struct regulator_consumer_supply omap3evm_vmmc2_supply[] = {
460 REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
463 /* VMMC2 for driving the WL12xx module */
464 static struct regulator_init_data omap3evm_vmmc2 = {
466 .valid_ops_mask = REGULATOR_CHANGE_STATUS,
468 .num_consumer_supplies = ARRAY_SIZE(omap3evm_vmmc2_supply),
469 .consumer_supplies = omap3evm_vmmc2_supply,
472 static struct fixed_voltage_config omap3evm_vwlan = {
473 .supply_name = "vwl1271",
474 .microvolts = 1800000, /* 1.80V */
475 .gpio = OMAP3EVM_WLAN_PMENA_GPIO,
476 .startup_delay = 70000, /* 70ms */
478 .enabled_at_boot = 0,
479 .init_data = &omap3evm_vmmc2,
482 static struct platform_device omap3evm_wlan_regulator = {
483 .name = "reg-fixed-voltage",
486 .platform_data = &omap3evm_vwlan,
490 struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
491 .board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */
496 static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
497 REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */
498 REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */
499 REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
500 REGULATOR_SUPPLY("vaux2", NULL),
503 static struct regulator_init_data omap3evm_vaux2 = {
508 .valid_modes_mask = REGULATOR_MODE_NORMAL
509 | REGULATOR_MODE_STANDBY,
510 .valid_ops_mask = REGULATOR_CHANGE_MODE
511 | REGULATOR_CHANGE_STATUS,
513 .num_consumer_supplies = ARRAY_SIZE(omap3evm_vaux2_supplies),
514 .consumer_supplies = omap3evm_vaux2_supplies,
517 static struct twl4030_platform_data omap3evm_twldata = {
518 /* platform_data for children goes here */
519 .keypad = &omap3evm_kp_data,
520 .gpio = &omap3evm_gpio_data,
521 .vio = &omap3evm_vio,
522 .vmmc1 = &omap3evm_vmmc1,
523 .vsim = &omap3evm_vsim,
526 static int __init omap3_evm_i2c_init(void)
528 omap3_pmic_get_config(&omap3evm_twldata,
529 TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
530 TWL_COMMON_PDATA_AUDIO,
531 TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
533 omap3evm_twldata.vdac->constraints.apply_uV = true;
534 omap3evm_twldata.vpll2->constraints.apply_uV = true;
536 omap3_pmic_init("twl4030", &omap3evm_twldata);
537 omap_register_i2c_bus(2, 400, NULL, 0);
538 omap_register_i2c_bus(3, 400, NULL, 0);
542 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
544 .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
545 .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
546 .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
549 /* PHY reset GPIO will be runtime programmed based on EVM version */
550 .reset_gpio_port[0] = -EINVAL,
551 .reset_gpio_port[1] = -EINVAL,
552 .reset_gpio_port[2] = -EINVAL
555 #ifdef CONFIG_OMAP_MUX
556 static struct omap_board_mux omap35x_board_mux[] __initdata = {
557 OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
558 OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
559 OMAP_PIN_OFF_WAKEUPENABLE),
560 OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
561 OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
562 OMAP_PIN_OFF_WAKEUPENABLE),
563 OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
565 OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
567 #ifdef CONFIG_WILINK_PLATFORM_DATA
568 /* WLAN IRQ - GPIO 149 */
569 OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
571 /* WLAN POWER ENABLE - GPIO 150 */
572 OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
574 /* MMC2 SDIO pin muxes for WL12xx */
575 OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
576 OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
577 OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
578 OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
579 OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
580 OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
582 { .reg_offset = OMAP_MUX_TERMINATOR },
585 static struct omap_board_mux omap36x_board_mux[] __initdata = {
586 OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
587 OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
588 OMAP_PIN_OFF_WAKEUPENABLE),
589 OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
590 OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
591 OMAP_PIN_OFF_WAKEUPENABLE),
592 /* AM/DM37x EVM: DSS data bus muxed with sys_boot */
593 OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
594 OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
595 OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
596 OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
597 OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
598 OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
599 OMAP3_MUX(SYS_BOOT0, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
600 OMAP3_MUX(SYS_BOOT1, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
601 OMAP3_MUX(SYS_BOOT3, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
602 OMAP3_MUX(SYS_BOOT4, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
603 OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
604 OMAP3_MUX(SYS_BOOT6, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
605 #ifdef CONFIG_WILINK_PLATFORM_DATA
606 /* WLAN IRQ - GPIO 149 */
607 OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
609 /* WLAN POWER ENABLE - GPIO 150 */
610 OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
612 /* MMC2 SDIO pin muxes for WL12xx */
613 OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
614 OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
615 OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
616 OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
617 OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
618 OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
621 { .reg_offset = OMAP_MUX_TERMINATOR },
624 #define omap35x_board_mux NULL
625 #define omap36x_board_mux NULL
628 static struct omap_musb_board_data musb_board_data = {
629 .interface_type = MUSB_INTERFACE_ULPI,
634 static struct gpio omap3_evm_ehci_gpios[] __initdata = {
635 { OMAP3_EVM_EHCI_VBUS, GPIOF_OUT_INIT_HIGH, "enable EHCI VBUS" },
636 { OMAP3_EVM_EHCI_SELECT, GPIOF_OUT_INIT_LOW, "select EHCI port" },
639 static void __init omap3_evm_wl12xx_init(void)
641 #ifdef CONFIG_WILINK_PLATFORM_DATA
644 /* WL12xx WLAN Init */
645 omap3evm_wlan_data.irq = gpio_to_irq(OMAP3EVM_WLAN_IRQ_GPIO);
646 ret = wl12xx_set_platform_data(&omap3evm_wlan_data);
648 pr_err("error setting wl12xx data: %d\n", ret);
649 ret = platform_device_register(&omap3evm_wlan_regulator);
651 pr_err("error registering wl12xx device: %d\n", ret);
655 static struct regulator_consumer_supply dummy_supplies[] = {
656 REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
657 REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
660 static struct mtd_partition omap3evm_nand_partitions[] = {
661 /* All the partition sizes are listed in terms of NAND block size */
666 .mask_flags = MTD_WRITEABLE
670 .offset = MTDPART_OFS_APPEND,
671 .size = 14*(SZ_128K),
672 .mask_flags = MTD_WRITEABLE
675 .name = "U-Boot Env",
676 .offset = MTDPART_OFS_APPEND,
681 .offset = MTDPART_OFS_APPEND,
685 .name = "File system",
686 .size = MTDPART_SIZ_FULL,
687 .offset = MTDPART_OFS_APPEND,
691 static void __init omap3_evm_init(void)
693 struct omap_board_mux *obm;
695 omap3_evm_get_revision();
696 regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
698 obm = (cpu_is_omap3630()) ? omap36x_board_mux : omap35x_board_mux;
699 omap3_mux_init(obm, OMAP_PACKAGE_CBB);
701 omap_mux_init_gpio(63, OMAP_PIN_INPUT);
702 omap_hsmmc_init(mmc);
704 if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
705 omap3evm_twldata.vaux2 = &omap3evm_vaux2;
707 omap3_evm_i2c_init();
709 omap_display_init(&omap3_evm_dss_data);
712 omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
714 /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
715 usb_nop_xceiv_register();
717 if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
718 /* enable EHCI VBUS using GPIO22 */
719 omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP);
720 /* Select EHCI port on main board */
721 omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT,
722 OMAP_PIN_INPUT_PULLUP);
723 gpio_request_array(omap3_evm_ehci_gpios,
724 ARRAY_SIZE(omap3_evm_ehci_gpios));
726 /* setup EHCI phy reset config */
727 omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
728 usbhs_bdata.reset_gpio_port[1] = 21;
730 /* EVM REV >= E can supply 500mA with EXTVBUS programming */
731 musb_board_data.power = 500;
732 musb_board_data.extvbus = 1;
734 /* setup EHCI phy reset on MDC */
735 omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
736 usbhs_bdata.reset_gpio_port[1] = 135;
738 usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
739 usb_musb_init(&musb_board_data);
740 usbhs_init(&usbhs_bdata);
741 board_nand_init(omap3evm_nand_partitions,
742 ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS,
743 NAND_BUSWIDTH_16, NULL);
745 omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL);
746 omap3evm_init_smsc911x();
747 omap3_evm_display_init();
748 omap3_evm_wl12xx_init();
749 omap_twl4030_audio_init("omap3evm", NULL);
752 MACHINE_START(OMAP3EVM, "OMAP3 EVM")
753 /* Maintainer: Syed Mohammed Khasim - Texas Instruments */
754 .atag_offset = 0x100,
755 .reserve = omap_reserve,
756 .map_io = omap3_map_io,
757 .init_early = omap35xx_init_early,
758 .init_irq = omap3_init_irq,
759 .handle_irq = omap3_intc_handle_irq,
760 .init_machine = omap3_evm_init,
761 .init_late = omap35xx_init_late,
762 .init_time = omap3_sync32k_timer_init,
763 .restart = omap3xxx_restart,