2 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
11 #include <dt-bindings/interrupt-controller/irq.h>
12 #include <dt-bindings/interrupt-controller/arm-gic.h>
15 model = "TI OMAP5 uEVM board";
16 compatible = "ti,omap5-uevm", "ti,omap5";
19 device_type = "memory";
20 reg = <0x80000000 0x7F000000>; /* 2032 MB */
23 vmmcsd_fixed: fixedregulator-mmcsd {
24 compatible = "regulator-fixed";
25 regulator-name = "vmmcsd_fixed";
26 regulator-min-microvolt = <3000000>;
27 regulator-max-microvolt = <3000000>;
30 /* HS USB Host PHY on PORT 2 */
31 hsusb2_phy: hsusb2_phy {
32 compatible = "usb-nop-xceiv";
33 reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
36 * Put the right clock phandle here when available
37 * clocks = <&auxclk1>;
38 * clock-names = "main_clk";
40 clock-frequency = <19200000>;
43 /* HS USB Host PHY on PORT 3 */
44 hsusb3_phy: hsusb3_phy {
45 compatible = "usb-nop-xceiv";
46 reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
50 compatible = "gpio-leds";
52 label = "omap5:blue:usr1";
53 gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
54 linux,default-trigger = "heartbeat";
55 default-state = "off";
61 pinctrl-names = "default";
72 twl6040_pins: pinmux_twl6040_pins {
73 pinctrl-single,pins = <
74 0x18a (PIN_OUTPUT | MUX_MODE6) /* perslimbus2_clock.gpio5_145 */
78 mcpdm_pins: pinmux_mcpdm_pins {
79 pinctrl-single,pins = <
80 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
81 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */
82 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */
83 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */
84 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */
88 dmic_pins: pinmux_dmic_pins {
89 pinctrl-single,pins = <
90 0x144 (PIN_INPUT | MUX_MODE0) /* abedmic_din1.abedmic_din1 */
91 0x146 (PIN_INPUT | MUX_MODE0) /* abedmic_din2.abedmic_din2 */
92 0x148 (PIN_INPUT | MUX_MODE0) /* abedmic_din3.abedmic_din3 */
93 0x14a (PIN_OUTPUT | MUX_MODE0) /* abedmic_clk1.abedmic_clk1 */
97 mcbsp1_pins: pinmux_mcbsp1_pins {
98 pinctrl-single,pins = <
99 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
100 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */
101 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */
102 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */
106 mcbsp2_pins: pinmux_mcbsp2_pins {
107 pinctrl-single,pins = <
108 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */
109 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */
110 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */
111 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */
115 i2c1_pins: pinmux_i2c1_pins {
116 pinctrl-single,pins = <
117 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
118 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
122 i2c5_pins: pinmux_i2c5_pins {
123 pinctrl-single,pins = <
124 0x184 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */
125 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */
129 mcspi2_pins: pinmux_mcspi2_pins {
130 pinctrl-single,pins = <
131 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
132 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
133 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
134 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs */
138 mcspi3_pins: pinmux_mcspi3_pins {
139 pinctrl-single,pins = <
140 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */
141 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */
142 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */
143 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */
147 mcspi4_pins: pinmux_mcspi4_pins {
148 pinctrl-single,pins = <
149 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */
150 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */
151 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */
152 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */
156 usbhost_pins: pinmux_usbhost_pins {
157 pinctrl-single,pins = <
158 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
159 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
161 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
162 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
164 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
165 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
169 led_gpio_pins: pinmux_led_gpio_pins {
170 pinctrl-single,pins = <
171 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
175 uart1_pins: pinmux_uart1_pins {
176 pinctrl-single,pins = <
177 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
178 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
179 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
180 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
184 uart3_pins: pinmux_uart3_pins {
185 pinctrl-single,pins = <
186 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
187 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
191 uart5_pins: pinmux_uart5_pins {
192 pinctrl-single,pins = <
193 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
194 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
195 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
196 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
203 pinctrl-names = "default";
208 usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
209 pinctrl-single,pins = <
210 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
216 vmmc-supply = <&ldo9_reg>;
221 vmmc-supply = <&vmmcsd_fixed>;
240 pinctrl-names = "default";
241 pinctrl-0 = <&i2c1_pins>;
243 clock-frequency = <400000>;
246 compatible = "ti,palmas";
247 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
248 interrupt-parent = <&gic>;
250 interrupt-controller;
251 #interrupt-cells = <2>;
253 extcon_usb3: palmas_usb {
254 compatible = "ti,palmas-usb-vid";
255 ti,enable-vbus-detection;
256 ti,enable-id-detection;
261 compatible = "ti,palmas-pmic";
262 interrupt-parent = <&palmas>;
263 interrupts = <14 IRQ_TYPE_NONE>;
264 interrupt-name = "short-irq";
269 smps123_reg: smps123 {
271 regulator-name = "smps123";
272 regulator-min-microvolt = < 600000>;
273 regulator-max-microvolt = <1500000>;
280 regulator-name = "smps45";
281 regulator-min-microvolt = < 600000>;
282 regulator-max-microvolt = <1310000>;
288 /* VDD_DDR3 - over VDD_SMPS6 */
289 regulator-name = "smps6";
290 regulator-min-microvolt = <1200000>;
291 regulator-max-microvolt = <1200000>;
297 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
298 regulator-name = "smps7";
299 regulator-min-microvolt = <1800000>;
300 regulator-max-microvolt = <1800000>;
307 regulator-name = "smps8";
308 regulator-min-microvolt = < 600000>;
309 regulator-max-microvolt = <1310000>;
315 /* VDDA_2v1_AUD over VDD_2v1 */
316 regulator-name = "smps9";
317 regulator-min-microvolt = <2100000>;
318 regulator-max-microvolt = <2100000>;
319 ti,smps-range = <0x80>;
322 smps10_out2_reg: smps10_out2 {
324 regulator-name = "smps10_out2";
325 regulator-min-microvolt = <5000000>;
326 regulator-max-microvolt = <5000000>;
331 smps10_out1_reg: smps10_out1 {
333 regulator-name = "smps10_out1";
334 regulator-min-microvolt = <5000000>;
335 regulator-max-microvolt = <5000000>;
341 /* VDDAPHY_CAM: vdda_csiport */
342 regulator-name = "ldo1";
343 regulator-min-microvolt = <1500000>;
344 regulator-max-microvolt = <1800000>;
348 /* VCC_2V8_DISP: Does not go anywhere */
349 regulator-name = "ldo2";
350 regulator-min-microvolt = <2800000>;
351 regulator-max-microvolt = <2800000>;
357 /* VDDAPHY_MDM: vdda_lli */
358 regulator-name = "ldo3";
359 regulator-min-microvolt = <1500000>;
360 regulator-max-microvolt = <1500000>;
362 /* Only if Modem is used */
367 /* VDDAPHY_DISP: vdda_dsiport/hdmi */
368 regulator-name = "ldo4";
369 regulator-min-microvolt = <1500000>;
370 regulator-max-microvolt = <1800000>;
374 /* VDDA_1V8_PHY: usb/sata/hdmi.. */
375 regulator-name = "ldo5";
376 regulator-min-microvolt = <1800000>;
377 regulator-max-microvolt = <1800000>;
383 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
384 regulator-name = "ldo6";
385 regulator-min-microvolt = <1200000>;
386 regulator-max-microvolt = <1200000>;
393 regulator-name = "ldo7";
394 regulator-min-microvolt = <2000000>;
395 regulator-max-microvolt = <2000000>;
396 /* Only for efuse reprograming! */
401 /* VDD_3v0: Does not go anywhere */
402 regulator-name = "ldo8";
403 regulator-min-microvolt = <3000000>;
404 regulator-max-microvolt = <3000000>;
411 /* VCC_DV_SDIO: vdds_sdcard */
412 regulator-name = "ldo9";
413 regulator-min-microvolt = <1800000>;
414 regulator-max-microvolt = <3000000>;
419 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
420 regulator-name = "ldoln";
421 regulator-min-microvolt = <1800000>;
422 regulator-max-microvolt = <1800000>;
428 /* VDDA_3V_USB: VDDA_USBHS33 */
429 regulator-name = "ldousb";
430 regulator-min-microvolt = <3250000>;
431 regulator-max-microvolt = <3250000>;
437 /* REGEN3 controls LDO9 supply to card */
438 regulator-name = "regen3";
448 pinctrl-names = "default";
449 pinctrl-0 = <&i2c5_pins>;
451 clock-frequency = <400000>;
459 port2-mode = "ehci-hsic";
460 port3-mode = "ehci-hsic";
464 phys = <0 &hsusb2_phy &hsusb3_phy>;
468 extcon = <&extcon_usb3>;
469 vbus-supply = <&smps10_out1_reg>;
477 pinctrl-names = "default";
478 pinctrl-0 = <&mcspi2_pins>;
482 pinctrl-names = "default";
483 pinctrl-0 = <&mcspi3_pins>;
487 pinctrl-names = "default";
488 pinctrl-0 = <&mcspi4_pins>;
492 pinctrl-names = "default";
493 pinctrl-0 = <&uart1_pins>;
497 pinctrl-names = "default";
498 pinctrl-0 = <&uart3_pins>;
502 pinctrl-names = "default";
503 pinctrl-0 = <&uart5_pins>;