2 * Copyright (C) 2011-2013 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
8 #include "elpida_ecb240abacn.dtsi"
12 device_type = "memory";
13 reg = <0x80000000 0x40000000>; /* 1 GB */
27 compatible = "gpio-leds";
28 pinctrl-names = "default";
34 label = "pandaboard::status1";
35 gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
36 linux,default-trigger = "heartbeat";
40 label = "pandaboard::status2";
41 gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
42 linux,default-trigger = "mmc0";
47 compatible = "ti,abe-twl6040";
48 ti,model = "PandaBoard";
50 ti,mclk-freq = <38400000>;
54 ti,twl6040 = <&twl6040>;
58 "Headset Stereophone", "HSOL",
59 "Headset Stereophone", "HSOR",
64 "HSMIC", "Headset Mic",
65 "Headset Mic", "Headset Mic Bias",
70 /* HS USB Port 1 Power */
71 hsusb1_power: hsusb1_power_reg {
72 compatible = "regulator-fixed";
73 regulator-name = "hsusb1_vbus";
74 regulator-min-microvolt = <3300000>;
75 regulator-max-microvolt = <3300000>;
76 gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; /* gpio_1 */
77 startup-delay-us = <70000>;
80 * boot-on is required along with always-on as the
81 * regulator framework doesn't enable the regulator
82 * if boot-on is not there.
88 /* HS USB Host PHY on PORT 1 */
89 hsusb1_phy: hsusb1_phy {
90 compatible = "usb-nop-xceiv";
91 reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */
92 vcc-supply = <&hsusb1_power>;
93 clocks = <&auxclk3_ck>;
94 clock-names = "main_clk";
95 clock-frequency = <19200000>;
98 /* regulator for wl12xx on sdio5 */
99 wl12xx_vmmc: wl12xx_vmmc {
100 pinctrl-names = "default";
101 pinctrl-0 = <&wl12xx_gpio>;
102 compatible = "regulator-fixed";
103 regulator-name = "vwl1271";
104 regulator-min-microvolt = <1800000>;
105 regulator-max-microvolt = <1800000>;
106 gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
107 startup-delay-us = <70000>;
112 compatible = "ti,tfp410";
113 powerdown-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* gpio_0 */
116 #address-cells = <1>;
122 tfp410_in: endpoint {
123 remote-endpoint = <&dpi_out>;
130 tfp410_out: endpoint {
131 remote-endpoint = <&dvi_connector_in>;
138 compatible = "dvi-connector";
143 ddc-i2c-bus = <&i2c3>;
146 dvi_connector_in: endpoint {
147 remote-endpoint = <&tfp410_out>;
152 tpd12s015: encoder1 {
153 compatible = "ti,tpd12s015";
155 gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
156 <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
157 <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
160 #address-cells = <1>;
166 tpd12s015_in: endpoint {
167 remote-endpoint = <&hdmi_out>;
174 tpd12s015_out: endpoint {
175 remote-endpoint = <&hdmi_connector_in>;
182 compatible = "hdmi-connector";
188 hdmi_connector_in: endpoint {
189 remote-endpoint = <&tpd12s015_out>;
196 pinctrl-names = "default";
205 twl6040_pins: pinmux_twl6040_pins {
206 pinctrl-single,pins = <
207 OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
208 OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */
212 mcpdm_pins: pinmux_mcpdm_pins {
213 pinctrl-single,pins = <
214 OMAP4_IOPAD(0x106, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */
215 OMAP4_IOPAD(0x108, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */
216 OMAP4_IOPAD(0x10a, PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */
217 OMAP4_IOPAD(0x10c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */
218 OMAP4_IOPAD(0x10e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
222 mcbsp1_pins: pinmux_mcbsp1_pins {
223 pinctrl-single,pins = <
224 OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
225 OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */
226 OMAP4_IOPAD(0x102, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */
227 OMAP4_IOPAD(0x104, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
231 dss_dpi_pins: pinmux_dss_dpi_pins {
232 pinctrl-single,pins = <
233 OMAP4_IOPAD(0x162, PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */
234 OMAP4_IOPAD(0x164, PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */
235 OMAP4_IOPAD(0x166, PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */
236 OMAP4_IOPAD(0x168, PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */
237 OMAP4_IOPAD(0x16a, PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */
238 OMAP4_IOPAD(0x16c, PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */
239 OMAP4_IOPAD(0x16e, PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */
240 OMAP4_IOPAD(0x170, PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */
241 OMAP4_IOPAD(0x172, PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */
242 OMAP4_IOPAD(0x174, PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */
243 OMAP4_IOPAD(0x176, PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */
245 OMAP4_IOPAD(0x1b4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */
246 OMAP4_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */
247 OMAP4_IOPAD(0x1b8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */
248 OMAP4_IOPAD(0x1ba, PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */
249 OMAP4_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */
250 OMAP4_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */
251 OMAP4_IOPAD(0x1c0, PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */
252 OMAP4_IOPAD(0x1c2, PIN_OUTPUT | MUX_MODE5) /* dispc2_de */
253 OMAP4_IOPAD(0x1c4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */
254 OMAP4_IOPAD(0x1c6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */
255 OMAP4_IOPAD(0x1c8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */
256 OMAP4_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */
257 OMAP4_IOPAD(0x1cc, PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */
258 OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */
260 OMAP4_IOPAD(0x1d0, PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */
261 OMAP4_IOPAD(0x1d2, PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */
262 OMAP4_IOPAD(0x1d4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */
266 tfp410_pins: pinmux_tfp410_pins {
267 pinctrl-single,pins = <
268 OMAP4_IOPAD(0x184, PIN_OUTPUT | MUX_MODE3) /* gpio_0 */
272 dss_hdmi_pins: pinmux_dss_hdmi_pins {
273 pinctrl-single,pins = <
274 OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
275 OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
276 OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
280 tpd12s015_pins: pinmux_tpd12s015_pins {
281 pinctrl-single,pins = <
282 OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */
283 OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */
284 OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */
288 hsusbb1_pins: pinmux_hsusbb1_pins {
289 pinctrl-single,pins = <
290 OMAP4_IOPAD(0x0c2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
291 OMAP4_IOPAD(0x0c4, PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
292 OMAP4_IOPAD(0x0c6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
293 OMAP4_IOPAD(0x0c8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
294 OMAP4_IOPAD(0x0ca, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
295 OMAP4_IOPAD(0x0cc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
296 OMAP4_IOPAD(0x0ce, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
297 OMAP4_IOPAD(0x0d0, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
298 OMAP4_IOPAD(0x0d2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
299 OMAP4_IOPAD(0x0d4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
300 OMAP4_IOPAD(0x0d6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
301 OMAP4_IOPAD(0x0d8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
305 i2c1_pins: pinmux_i2c1_pins {
306 pinctrl-single,pins = <
307 OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
308 OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
312 i2c2_pins: pinmux_i2c2_pins {
313 pinctrl-single,pins = <
314 OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
315 OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
319 i2c3_pins: pinmux_i2c3_pins {
320 pinctrl-single,pins = <
321 OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
322 OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
326 i2c4_pins: pinmux_i2c4_pins {
327 pinctrl-single,pins = <
328 OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
329 OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
334 * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
335 * REVISIT: Are the pull-ups needed for GPIO 48 and 49?
337 wl12xx_gpio: pinmux_wl12xx_gpio {
338 pinctrl-single,pins = <
339 OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */
340 OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 */
341 OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */
342 OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 */
346 /* wl12xx GPIO inputs and SDIO pins */
347 wl12xx_pins: pinmux_wl12xx_pins {
348 pinctrl-single,pins = <
349 OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */
350 OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */
351 OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */
352 OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */
353 OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */
354 OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */
355 OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */
356 OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */
362 led_wkgpio_pins: pinmux_leds_wkpins {
363 pinctrl-single,pins = <
364 OMAP4_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */
365 OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
371 pinctrl-names = "default";
372 pinctrl-0 = <&i2c1_pins>;
374 clock-frequency = <400000>;
379 interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
383 compatible = "ti,twl6040";
387 pinctrl-names = "default";
388 pinctrl-0 = <&twl6040_pins>;
391 interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
392 ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */
394 vio-supply = <&v1v8>;
395 v2v1-supply = <&v2v1>;
400 #include "twl6030.dtsi"
401 #include "twl6030_omap4.dtsi"
404 pinctrl-names = "default";
405 pinctrl-0 = <&i2c2_pins>;
407 clock-frequency = <400000>;
411 pinctrl-names = "default";
412 pinctrl-0 = <&i2c3_pins>;
414 clock-frequency = <100000>;
417 * Display monitor features are burnt in their EEPROM as EDID data.
418 * The EEPROM is connected as I2C slave device.
421 compatible = "ti,eeprom";
427 pinctrl-names = "default";
428 pinctrl-0 = <&i2c4_pins>;
430 clock-frequency = <400000>;
434 vmmc-supply = <&vmmc>;
451 pinctrl-names = "default";
452 pinctrl-0 = <&wl12xx_pins>;
453 vmmc-supply = <&wl12xx_vmmc>;
454 interrupts-extended = <&wakeupgen GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH
455 &omap4_pmx_core 0x10e>;
460 #address-cells = <1>;
463 compatible = "ti,wl1271";
465 interrupt-parent = <&gpio2>;
466 interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 53 */
467 ref-clock-frequency = <38400000>;
473 device-handle = <&elpida_ECB240ABACN>;
478 device-handle = <&elpida_ECB240ABACN>;
482 pinctrl-names = "default";
483 pinctrl-0 = <&mcbsp1_pins>;
488 pinctrl-names = "default";
489 pinctrl-0 = <&mcpdm_pins>;
492 clock-names = "pdmclk";
497 &twl_usb_comparator {
498 usb-supply = <&vusb>;
502 interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
503 &omap4_pmx_core OMAP4_UART2_RX>;
507 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
508 &omap4_pmx_core OMAP4_UART3_RX>;
512 interrupts-extended = <&wakeupgen GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH
513 &omap4_pmx_core OMAP4_UART4_RX>;
517 interface-type = <1>;
523 port1-mode = "ehci-phy";
527 phys = <&hsusb1_phy>;
529 #address-cells = <1>;
533 compatible = "usb424,9514";
535 #address-cells = <1>;
538 ethernet: usbether@1 {
539 compatible = "usb424,ec00";
550 remote-endpoint = <&tfp410_in>;
558 vdd-supply = <&vcxio>;
563 vdda-supply = <&vdac>;
567 remote-endpoint = <&tpd12s015_in>;