2 * This program is free software; you can redistribute it and/or modify
3 * it under the terms of the GNU General Public License version 2 as
4 * published by the Free Software Foundation.
7 #include <dt-bindings/input/input.h>
21 device_type = "memory";
26 compatible = "gpio-leds";
29 gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* LEDA */
30 linux,default-trigger = "none";
36 ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
39 compatible = "ti,omap2-nand";
40 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
41 interrupt-parent = <&gpmc>;
42 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
43 <1 IRQ_TYPE_NONE>; /* termcount */
44 linux,mtd-name = "micron,mt29f4g16abbda3w";
45 nand-bus-width = <16>;
46 ti,nand-ecc-opt = "bch8";
47 rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
48 gpmc,sync-clk-ps = <0>;
50 gpmc,cs-rd-off-ns = <44>;
51 gpmc,cs-wr-off-ns = <44>;
53 gpmc,adv-rd-off-ns = <34>;
54 gpmc,adv-wr-off-ns = <44>;
55 gpmc,we-off-ns = <40>;
56 gpmc,oe-off-ns = <54>;
57 gpmc,access-ns = <64>;
58 gpmc,rd-cycle-ns = <82>;
59 gpmc,wr-cycle-ns = <82>;
60 gpmc,wr-access-ns = <40>;
61 gpmc,wr-data-mux-bus-ns = <0>;
62 gpmc,device-width = <2>;
69 pinctrl-names = "default";
70 pinctrl-0 = <&i2c1_pins>;
71 clock-frequency = <2600000>;
75 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
76 interrupt-parent = <&intc>;
78 compatible = "ti,twl4030-audio";
86 clock-frequency = <400000>;
90 clock-frequency = <400000>;
92 compatible = "atmel,24c64";
99 mcbsp2_pins: pinmux_mcbsp2_pins {
100 pinctrl-single,pins = <
101 OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
102 OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */
103 OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */
104 OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */
107 uart2_pins: pinmux_uart2_pins {
108 pinctrl-single,pins = <
109 OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */
110 OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/
111 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
112 OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
113 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
116 mcspi1_pins: pinmux_mcspi1_pins {
117 pinctrl-single,pins = <
118 OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
119 OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
120 OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
121 OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
124 hsusb_otg_pins: pinmux_hsusb_otg_pins {
125 pinctrl-single,pins = <
126 OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
127 OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
128 OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
129 OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
131 OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
132 OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
133 OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
134 OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
135 OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
136 OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
137 OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
138 OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
141 i2c1_pins: pinmux_i2c1_pins {
142 pinctrl-single,pins = <
143 OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */
144 OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */
150 interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
151 pinctrl-names = "default";
152 pinctrl-0 = <&uart2_pins>;
156 pinctrl-names = "default";
157 pinctrl-0 = <&mcspi1_pins>;
160 #include "twl4030.dtsi"
161 #include "twl4030_omap3.dtsi"
165 compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";