1 Voltage/Current Regulators
4 - regulator-name: A string used as a descriptive name for regulator outputs
5 - regulator-min-microvolt: smallest voltage consumers may set
6 - regulator-max-microvolt: largest voltage consumers may set
7 - regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops
8 - regulator-min-microamp: smallest current consumers may set
9 - regulator-max-microamp: largest current consumers may set
10 - regulator-input-current-limit-microamp: maximum input current regulator allows
11 - regulator-always-on: boolean, regulator should never be disabled
12 - regulator-boot-on: bootloader/firmware enabled regulator
13 - regulator-allow-bypass: allow the regulator to go into bypass mode
14 - regulator-allow-set-load: allow the regulator performance level to be configured
15 - <name>-supply: phandle to the parent supply/regulator node
16 - regulator-ramp-delay: ramp delay for regulator(in uV/us)
17 For hardware which supports disabling ramp rate, it should be explicitly
18 initialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay.
19 - regulator-enable-ramp-delay: The time taken, in microseconds, for the supply
20 rail to reach the target voltage, plus/minus whatever tolerance the board
21 design requires. This property describes the total system ramp time
22 required due to the combination of internal ramping of the regulator itself,
23 and board design issues such as trace capacitance and load on the supply.
24 - regulator-settling-time-us: Settling time, in microseconds, for voltage
25 change if regulator have the constant time for any level voltage change.
26 This is useful when regulator have exponential voltage change.
27 - regulator-settling-time-up-us: Settling time, in microseconds, for voltage
28 increase if the regulator needs a constant time to settle after voltage
29 increases of any level. This is useful for regulators with exponential
31 - regulator-settling-time-down-us: Settling time, in microseconds, for voltage
32 decrease if the regulator needs a constant time to settle after voltage
33 decreases of any level. This is useful for regulators with exponential
35 - regulator-soft-start: Enable soft start so that voltage ramps slowly
36 - regulator-state-mem sub-root node for Suspend-to-RAM mode
37 : suspend to memory, the device goes to sleep, but all data stored in memory,
38 only some external interrupt can wake the device.
39 - regulator-state-disk sub-root node for Suspend-to-DISK mode
40 : suspend to disk, this state operates similarly to Suspend-to-RAM,
41 but includes a final step of writing memory contents to disk.
42 - regulator-state-[mem/disk] node has following common properties:
43 - regulator-on-in-suspend: regulator should be on in suspend state.
44 - regulator-off-in-suspend: regulator should be off in suspend state.
45 - regulator-suspend-microvolt: regulator should be set to this voltage
47 - regulator-mode: operating mode in the given suspend state.
48 The set of possible operating modes depends on the capabilities of
49 every hardware so the valid modes are documented on each regulator
50 device tree binding document.
51 - regulator-initial-mode: initial operating mode. The set of possible operating
52 modes depends on the capabilities of every hardware so each device binding
53 documentation explains which values the regulator supports.
54 - regulator-system-load: Load in uA present on regulator that is not captured by
56 - regulator-pull-down: Enable pull down resistor when the regulator is disabled.
57 - regulator-over-current-protection: Enable over current protection.
58 - regulator-active-discharge: tristate, enable/disable active discharge of
59 regulators. The values are:
60 0: Disable active discharge.
61 1: Enable active discharge.
62 Absence of this property will leave configuration to default.
64 Deprecated properties:
65 - regulator-compatible: If a regulator chip contains multiple
66 regulators, and if the chip's binding contains a child node that
67 describes each regulator, then this property indicates which regulator
68 this child node is intended to configure. If this property is missing,
69 the node's name will be used instead.
74 regulator-min-microvolt = <1000000>;
75 regulator-max-microvolt = <2500000>;
80 regulator-on-in-suspend;
85 Consumer nodes can reference one or more of its supplies/
86 regulators using the below bindings.
88 - <name>-supply: phandle to the regulator node
90 These are the same bindings that a regulator in the above
91 example used to reference its own supply, in which case
92 its just seen as a special case of a regulator being a
95 Example of a consumer device node (mmc) referencing two
96 regulators (twl_reg1 and twl_reg2),
98 twl_reg1: regulator@0 {
104 twl_reg2: regulator@1 {
113 vmmc-supply = <&twl_reg1>;
114 vmmcaux-supply = <&twl_reg2>;