| 1 | // SPDX-License-Identifier: GPL-2.0-only |
| 2 | /* |
| 3 | * TI TRF7970a RFID/NFC Transceiver Driver |
| 4 | * |
| 5 | * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com |
| 6 | * |
| 7 | * Author: Erick Macias <emacias@ti.com> |
| 8 | * Author: Felipe Balbi <balbi@ti.com> |
| 9 | * Author: Mark A. Greer <mgreer@animalcreek.com> |
| 10 | */ |
| 11 | |
| 12 | #include <linux/module.h> |
| 13 | #include <linux/device.h> |
| 14 | #include <linux/netdevice.h> |
| 15 | #include <linux/interrupt.h> |
| 16 | #include <linux/pm_runtime.h> |
| 17 | #include <linux/nfc.h> |
| 18 | #include <linux/skbuff.h> |
| 19 | #include <linux/delay.h> |
| 20 | #include <linux/gpio/consumer.h> |
| 21 | #include <linux/of.h> |
| 22 | #include <linux/spi/spi.h> |
| 23 | #include <linux/regulator/consumer.h> |
| 24 | |
| 25 | #include <net/nfc/nfc.h> |
| 26 | #include <net/nfc/digital.h> |
| 27 | |
| 28 | /* There are 3 ways the host can communicate with the trf7970a: |
| 29 | * parallel mode, SPI with Slave Select (SS) mode, and SPI without |
| 30 | * SS mode. The driver only supports the two SPI modes. |
| 31 | * |
| 32 | * The trf7970a is very timing sensitive and the VIN, EN2, and EN |
| 33 | * pins must asserted in that order and with specific delays in between. |
| 34 | * The delays used in the driver were provided by TI and have been |
| 35 | * confirmed to work with this driver. There is a bug with the current |
| 36 | * version of the trf7970a that requires that EN2 remain low no matter |
| 37 | * what. If it goes high, it will generate an RF field even when in |
| 38 | * passive target mode. TI has indicated that the chip will work okay |
| 39 | * when EN2 is left low. The 'en2-rf-quirk' device tree property |
| 40 | * indicates that trf7970a currently being used has the erratum and |
| 41 | * that EN2 must be kept low. |
| 42 | * |
| 43 | * Timeouts are implemented using the delayed workqueue kernel facility. |
| 44 | * Timeouts are required so things don't hang when there is no response |
| 45 | * from the trf7970a (or tag). Using this mechanism creates a race with |
| 46 | * interrupts, however. That is, an interrupt and a timeout could occur |
| 47 | * closely enough together that one is blocked by the mutex while the other |
| 48 | * executes. When the timeout handler executes first and blocks the |
| 49 | * interrupt handler, it will eventually set the state to IDLE so the |
| 50 | * interrupt handler will check the state and exit with no harm done. |
| 51 | * When the interrupt handler executes first and blocks the timeout handler, |
| 52 | * the cancel_delayed_work() call will know that it didn't cancel the |
| 53 | * work item (i.e., timeout) and will return zero. That return code is |
| 54 | * used by the timer handler to indicate that it should ignore the timeout |
| 55 | * once its unblocked. |
| 56 | * |
| 57 | * Aborting an active command isn't as simple as it seems because the only |
| 58 | * way to abort a command that's already been sent to the tag is so turn |
| 59 | * off power to the tag. If we do that, though, we'd have to go through |
| 60 | * the entire anticollision procedure again but the digital layer doesn't |
| 61 | * support that. So, if an abort is received before trf7970a_send_cmd() |
| 62 | * has sent the command to the tag, it simply returns -ECANCELED. If the |
| 63 | * command has already been sent to the tag, then the driver continues |
| 64 | * normally and recieves the response data (or error) but just before |
| 65 | * sending the data upstream, it frees the rx_skb and sends -ECANCELED |
| 66 | * upstream instead. If the command failed, that error will be sent |
| 67 | * upstream. |
| 68 | * |
| 69 | * When recieving data from a tag and the interrupt status register has |
| 70 | * only the SRX bit set, it means that all of the data has been received |
| 71 | * (once what's in the fifo has been read). However, depending on timing |
| 72 | * an interrupt status with only the SRX bit set may not be recived. In |
| 73 | * those cases, the timeout mechanism is used to wait 20 ms in case more |
| 74 | * data arrives. After 20 ms, it is assumed that all of the data has been |
| 75 | * received and the accumulated rx data is sent upstream. The |
| 76 | * 'TRF7970A_ST_WAIT_FOR_RX_DATA_CONT' state is used for this purpose |
| 77 | * (i.e., it indicates that some data has been received but we're not sure |
| 78 | * if there is more coming so a timeout in this state means all data has |
| 79 | * been received and there isn't an error). The delay is 20 ms since delays |
| 80 | * of ~16 ms have been observed during testing. |
| 81 | * |
| 82 | * When transmitting a frame larger than the FIFO size (127 bytes), the |
| 83 | * driver will wait 20 ms for the FIFO to drain past the low-watermark |
| 84 | * and generate an interrupt. The low-watermark set to 32 bytes so the |
| 85 | * interrupt should fire after 127 - 32 = 95 bytes have been sent. At |
| 86 | * the lowest possible bit rate (6.62 kbps for 15693), it will take up |
| 87 | * to ~14.35 ms so 20 ms is used for the timeout. |
| 88 | * |
| 89 | * Type 2 write and sector select commands respond with a 4-bit ACK or NACK. |
| 90 | * Having only 4 bits in the FIFO won't normally generate an interrupt so |
| 91 | * driver enables the '4_bit_RX' bit of the Special Functions register 1 |
| 92 | * to cause an interrupt in that case. Leaving that bit for a read command |
| 93 | * messes up the data returned so it is only enabled when the framing is |
| 94 | * 'NFC_DIGITAL_FRAMING_NFCA_T2T' and the command is not a read command. |
| 95 | * Unfortunately, that means that the driver has to peek into tx frames |
| 96 | * when the framing is 'NFC_DIGITAL_FRAMING_NFCA_T2T'. This is done by |
| 97 | * the trf7970a_per_cmd_config() routine. |
| 98 | * |
| 99 | * ISO/IEC 15693 frames specify whether to use single or double sub-carrier |
| 100 | * frequencies and whether to use low or high data rates in the flags byte |
| 101 | * of the frame. This means that the driver has to peek at all 15693 frames |
| 102 | * to determine what speed to set the communication to. In addition, write |
| 103 | * and lock commands use the OPTION flag to indicate that an EOF must be |
| 104 | * sent to the tag before it will send its response. So the driver has to |
| 105 | * examine all frames for that reason too. |
| 106 | * |
| 107 | * It is unclear how long to wait before sending the EOF. According to the |
| 108 | * Note under Table 1-1 in section 1.6 of |
| 109 | * http://www.ti.com/lit/ug/scbu011/scbu011.pdf, that wait should be at least |
| 110 | * 10 ms for TI Tag-it HF-I tags; however testing has shown that is not long |
| 111 | * enough so 20 ms is used. So the timer is set to 40 ms - 20 ms to drain |
| 112 | * up to 127 bytes in the FIFO at the lowest bit rate plus another 20 ms to |
| 113 | * ensure the wait is long enough before sending the EOF. This seems to work |
| 114 | * reliably. |
| 115 | */ |
| 116 | |
| 117 | #define TRF7970A_SUPPORTED_PROTOCOLS \ |
| 118 | (NFC_PROTO_MIFARE_MASK | NFC_PROTO_ISO14443_MASK | \ |
| 119 | NFC_PROTO_ISO14443_B_MASK | NFC_PROTO_FELICA_MASK | \ |
| 120 | NFC_PROTO_ISO15693_MASK | NFC_PROTO_NFC_DEP_MASK) |
| 121 | |
| 122 | #define TRF7970A_AUTOSUSPEND_DELAY 30000 /* 30 seconds */ |
| 123 | #define TRF7970A_13MHZ_CLOCK_FREQUENCY 13560000 |
| 124 | #define TRF7970A_27MHZ_CLOCK_FREQUENCY 27120000 |
| 125 | |
| 126 | #define TRF7970A_RX_SKB_ALLOC_SIZE 256 |
| 127 | |
| 128 | #define TRF7970A_FIFO_SIZE 127 |
| 129 | |
| 130 | /* TX length is 3 nibbles long ==> 4KB - 1 bytes max */ |
| 131 | #define TRF7970A_TX_MAX (4096 - 1) |
| 132 | |
| 133 | #define TRF7970A_WAIT_FOR_TX_IRQ 20 |
| 134 | #define TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT 20 |
| 135 | #define TRF7970A_WAIT_FOR_FIFO_DRAIN_TIMEOUT 20 |
| 136 | #define TRF7970A_WAIT_TO_ISSUE_ISO15693_EOF 40 |
| 137 | |
| 138 | /* Guard times for various RF technologies (in us) */ |
| 139 | #define TRF7970A_GUARD_TIME_NFCA 5000 |
| 140 | #define TRF7970A_GUARD_TIME_NFCB 5000 |
| 141 | #define TRF7970A_GUARD_TIME_NFCF 20000 |
| 142 | #define TRF7970A_GUARD_TIME_15693 1000 |
| 143 | |
| 144 | /* Quirks */ |
| 145 | /* Erratum: When reading IRQ Status register on trf7970a, we must issue a |
| 146 | * read continuous command for IRQ Status and Collision Position registers. |
| 147 | */ |
| 148 | #define TRF7970A_QUIRK_IRQ_STATUS_READ BIT(0) |
| 149 | #define TRF7970A_QUIRK_EN2_MUST_STAY_LOW BIT(1) |
| 150 | |
| 151 | /* Direct commands */ |
| 152 | #define TRF7970A_CMD_IDLE 0x00 |
| 153 | #define TRF7970A_CMD_SOFT_INIT 0x03 |
| 154 | #define TRF7970A_CMD_RF_COLLISION 0x04 |
| 155 | #define TRF7970A_CMD_RF_COLLISION_RESPONSE_N 0x05 |
| 156 | #define TRF7970A_CMD_RF_COLLISION_RESPONSE_0 0x06 |
| 157 | #define TRF7970A_CMD_FIFO_RESET 0x0f |
| 158 | #define TRF7970A_CMD_TRANSMIT_NO_CRC 0x10 |
| 159 | #define TRF7970A_CMD_TRANSMIT 0x11 |
| 160 | #define TRF7970A_CMD_DELAY_TRANSMIT_NO_CRC 0x12 |
| 161 | #define TRF7970A_CMD_DELAY_TRANSMIT 0x13 |
| 162 | #define TRF7970A_CMD_EOF 0x14 |
| 163 | #define TRF7970A_CMD_CLOSE_SLOT 0x15 |
| 164 | #define TRF7970A_CMD_BLOCK_RX 0x16 |
| 165 | #define TRF7970A_CMD_ENABLE_RX 0x17 |
| 166 | #define TRF7970A_CMD_TEST_INT_RF 0x18 |
| 167 | #define TRF7970A_CMD_TEST_EXT_RF 0x19 |
| 168 | #define TRF7970A_CMD_RX_GAIN_ADJUST 0x1a |
| 169 | |
| 170 | /* Bits determining whether its a direct command or register R/W, |
| 171 | * whether to use a continuous SPI transaction or not, and the actual |
| 172 | * direct cmd opcode or register address. |
| 173 | */ |
| 174 | #define TRF7970A_CMD_BIT_CTRL BIT(7) |
| 175 | #define TRF7970A_CMD_BIT_RW BIT(6) |
| 176 | #define TRF7970A_CMD_BIT_CONTINUOUS BIT(5) |
| 177 | #define TRF7970A_CMD_BIT_OPCODE(opcode) ((opcode) & 0x1f) |
| 178 | |
| 179 | /* Registers addresses */ |
| 180 | #define TRF7970A_CHIP_STATUS_CTRL 0x00 |
| 181 | #define TRF7970A_ISO_CTRL 0x01 |
| 182 | #define TRF7970A_ISO14443B_TX_OPTIONS 0x02 |
| 183 | #define TRF7970A_ISO14443A_HIGH_BITRATE_OPTIONS 0x03 |
| 184 | #define TRF7970A_TX_TIMER_SETTING_H_BYTE 0x04 |
| 185 | #define TRF7970A_TX_TIMER_SETTING_L_BYTE 0x05 |
| 186 | #define TRF7970A_TX_PULSE_LENGTH_CTRL 0x06 |
| 187 | #define TRF7970A_RX_NO_RESPONSE_WAIT 0x07 |
| 188 | #define TRF7970A_RX_WAIT_TIME 0x08 |
| 189 | #define TRF7970A_MODULATOR_SYS_CLK_CTRL 0x09 |
| 190 | #define TRF7970A_RX_SPECIAL_SETTINGS 0x0a |
| 191 | #define TRF7970A_REG_IO_CTRL 0x0b |
| 192 | #define TRF7970A_IRQ_STATUS 0x0c |
| 193 | #define TRF7970A_COLLISION_IRQ_MASK 0x0d |
| 194 | #define TRF7970A_COLLISION_POSITION 0x0e |
| 195 | #define TRF7970A_RSSI_OSC_STATUS 0x0f |
| 196 | #define TRF7970A_SPECIAL_FCN_REG1 0x10 |
| 197 | #define TRF7970A_SPECIAL_FCN_REG2 0x11 |
| 198 | #define TRF7970A_RAM1 0x12 |
| 199 | #define TRF7970A_RAM2 0x13 |
| 200 | #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS 0x14 |
| 201 | #define TRF7970A_NFC_LOW_FIELD_LEVEL 0x16 |
| 202 | #define TRF7970A_NFCID1 0x17 |
| 203 | #define TRF7970A_NFC_TARGET_LEVEL 0x18 |
| 204 | #define TRF79070A_NFC_TARGET_PROTOCOL 0x19 |
| 205 | #define TRF7970A_TEST_REGISTER1 0x1a |
| 206 | #define TRF7970A_TEST_REGISTER2 0x1b |
| 207 | #define TRF7970A_FIFO_STATUS 0x1c |
| 208 | #define TRF7970A_TX_LENGTH_BYTE1 0x1d |
| 209 | #define TRF7970A_TX_LENGTH_BYTE2 0x1e |
| 210 | #define TRF7970A_FIFO_IO_REGISTER 0x1f |
| 211 | |
| 212 | /* Chip Status Control Register Bits */ |
| 213 | #define TRF7970A_CHIP_STATUS_VRS5_3 BIT(0) |
| 214 | #define TRF7970A_CHIP_STATUS_REC_ON BIT(1) |
| 215 | #define TRF7970A_CHIP_STATUS_AGC_ON BIT(2) |
| 216 | #define TRF7970A_CHIP_STATUS_PM_ON BIT(3) |
| 217 | #define TRF7970A_CHIP_STATUS_RF_PWR BIT(4) |
| 218 | #define TRF7970A_CHIP_STATUS_RF_ON BIT(5) |
| 219 | #define TRF7970A_CHIP_STATUS_DIRECT BIT(6) |
| 220 | #define TRF7970A_CHIP_STATUS_STBY BIT(7) |
| 221 | |
| 222 | /* ISO Control Register Bits */ |
| 223 | #define TRF7970A_ISO_CTRL_15693_SGL_1OF4_662 0x00 |
| 224 | #define TRF7970A_ISO_CTRL_15693_SGL_1OF256_662 0x01 |
| 225 | #define TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648 0x02 |
| 226 | #define TRF7970A_ISO_CTRL_15693_SGL_1OF256_2648 0x03 |
| 227 | #define TRF7970A_ISO_CTRL_15693_DBL_1OF4_667a 0x04 |
| 228 | #define TRF7970A_ISO_CTRL_15693_DBL_1OF256_667 0x05 |
| 229 | #define TRF7970A_ISO_CTRL_15693_DBL_1OF4_2669 0x06 |
| 230 | #define TRF7970A_ISO_CTRL_15693_DBL_1OF256_2669 0x07 |
| 231 | #define TRF7970A_ISO_CTRL_14443A_106 0x08 |
| 232 | #define TRF7970A_ISO_CTRL_14443A_212 0x09 |
| 233 | #define TRF7970A_ISO_CTRL_14443A_424 0x0a |
| 234 | #define TRF7970A_ISO_CTRL_14443A_848 0x0b |
| 235 | #define TRF7970A_ISO_CTRL_14443B_106 0x0c |
| 236 | #define TRF7970A_ISO_CTRL_14443B_212 0x0d |
| 237 | #define TRF7970A_ISO_CTRL_14443B_424 0x0e |
| 238 | #define TRF7970A_ISO_CTRL_14443B_848 0x0f |
| 239 | #define TRF7970A_ISO_CTRL_FELICA_212 0x1a |
| 240 | #define TRF7970A_ISO_CTRL_FELICA_424 0x1b |
| 241 | #define TRF7970A_ISO_CTRL_NFC_NFCA_106 0x01 |
| 242 | #define TRF7970A_ISO_CTRL_NFC_NFCF_212 0x02 |
| 243 | #define TRF7970A_ISO_CTRL_NFC_NFCF_424 0x03 |
| 244 | #define TRF7970A_ISO_CTRL_NFC_CE_14443A 0x00 |
| 245 | #define TRF7970A_ISO_CTRL_NFC_CE_14443B 0x01 |
| 246 | #define TRF7970A_ISO_CTRL_NFC_CE BIT(2) |
| 247 | #define TRF7970A_ISO_CTRL_NFC_ACTIVE BIT(3) |
| 248 | #define TRF7970A_ISO_CTRL_NFC_INITIATOR BIT(4) |
| 249 | #define TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE BIT(5) |
| 250 | #define TRF7970A_ISO_CTRL_RFID BIT(5) |
| 251 | #define TRF7970A_ISO_CTRL_DIR_MODE BIT(6) |
| 252 | #define TRF7970A_ISO_CTRL_RX_CRC_N BIT(7) /* true == No CRC */ |
| 253 | |
| 254 | #define TRF7970A_ISO_CTRL_RFID_SPEED_MASK 0x1f |
| 255 | |
| 256 | /* Modulator and SYS_CLK Control Register Bits */ |
| 257 | #define TRF7970A_MODULATOR_DEPTH(n) ((n) & 0x7) |
| 258 | #define TRF7970A_MODULATOR_DEPTH_ASK10 (TRF7970A_MODULATOR_DEPTH(0)) |
| 259 | #define TRF7970A_MODULATOR_DEPTH_OOK (TRF7970A_MODULATOR_DEPTH(1)) |
| 260 | #define TRF7970A_MODULATOR_DEPTH_ASK7 (TRF7970A_MODULATOR_DEPTH(2)) |
| 261 | #define TRF7970A_MODULATOR_DEPTH_ASK8_5 (TRF7970A_MODULATOR_DEPTH(3)) |
| 262 | #define TRF7970A_MODULATOR_DEPTH_ASK13 (TRF7970A_MODULATOR_DEPTH(4)) |
| 263 | #define TRF7970A_MODULATOR_DEPTH_ASK16 (TRF7970A_MODULATOR_DEPTH(5)) |
| 264 | #define TRF7970A_MODULATOR_DEPTH_ASK22 (TRF7970A_MODULATOR_DEPTH(6)) |
| 265 | #define TRF7970A_MODULATOR_DEPTH_ASK30 (TRF7970A_MODULATOR_DEPTH(7)) |
| 266 | #define TRF7970A_MODULATOR_EN_ANA BIT(3) |
| 267 | #define TRF7970A_MODULATOR_CLK(n) (((n) & 0x3) << 4) |
| 268 | #define TRF7970A_MODULATOR_CLK_DISABLED (TRF7970A_MODULATOR_CLK(0)) |
| 269 | #define TRF7970A_MODULATOR_CLK_3_6 (TRF7970A_MODULATOR_CLK(1)) |
| 270 | #define TRF7970A_MODULATOR_CLK_6_13 (TRF7970A_MODULATOR_CLK(2)) |
| 271 | #define TRF7970A_MODULATOR_CLK_13_27 (TRF7970A_MODULATOR_CLK(3)) |
| 272 | #define TRF7970A_MODULATOR_EN_OOK BIT(6) |
| 273 | #define TRF7970A_MODULATOR_27MHZ BIT(7) |
| 274 | |
| 275 | #define TRF7970A_RX_SPECIAL_SETTINGS_NO_LIM BIT(0) |
| 276 | #define TRF7970A_RX_SPECIAL_SETTINGS_AGCR BIT(1) |
| 277 | #define TRF7970A_RX_SPECIAL_SETTINGS_GD_0DB (0x0 << 2) |
| 278 | #define TRF7970A_RX_SPECIAL_SETTINGS_GD_5DB (0x1 << 2) |
| 279 | #define TRF7970A_RX_SPECIAL_SETTINGS_GD_10DB (0x2 << 2) |
| 280 | #define TRF7970A_RX_SPECIAL_SETTINGS_GD_15DB (0x3 << 2) |
| 281 | #define TRF7970A_RX_SPECIAL_SETTINGS_HBT BIT(4) |
| 282 | #define TRF7970A_RX_SPECIAL_SETTINGS_M848 BIT(5) |
| 283 | #define TRF7970A_RX_SPECIAL_SETTINGS_C424 BIT(6) |
| 284 | #define TRF7970A_RX_SPECIAL_SETTINGS_C212 BIT(7) |
| 285 | |
| 286 | #define TRF7970A_REG_IO_CTRL_VRS(v) ((v) & 0x07) |
| 287 | #define TRF7970A_REG_IO_CTRL_IO_LOW BIT(5) |
| 288 | #define TRF7970A_REG_IO_CTRL_EN_EXT_PA BIT(6) |
| 289 | #define TRF7970A_REG_IO_CTRL_AUTO_REG BIT(7) |
| 290 | |
| 291 | /* IRQ Status Register Bits */ |
| 292 | #define TRF7970A_IRQ_STATUS_NORESP BIT(0) /* ISO15693 only */ |
| 293 | #define TRF7970A_IRQ_STATUS_NFC_COL_ERROR BIT(0) |
| 294 | #define TRF7970A_IRQ_STATUS_COL BIT(1) |
| 295 | #define TRF7970A_IRQ_STATUS_FRAMING_EOF_ERROR BIT(2) |
| 296 | #define TRF7970A_IRQ_STATUS_NFC_RF BIT(2) |
| 297 | #define TRF7970A_IRQ_STATUS_PARITY_ERROR BIT(3) |
| 298 | #define TRF7970A_IRQ_STATUS_NFC_SDD BIT(3) |
| 299 | #define TRF7970A_IRQ_STATUS_CRC_ERROR BIT(4) |
| 300 | #define TRF7970A_IRQ_STATUS_NFC_PROTO_ERROR BIT(4) |
| 301 | #define TRF7970A_IRQ_STATUS_FIFO BIT(5) |
| 302 | #define TRF7970A_IRQ_STATUS_SRX BIT(6) |
| 303 | #define TRF7970A_IRQ_STATUS_TX BIT(7) |
| 304 | |
| 305 | #define TRF7970A_IRQ_STATUS_ERROR \ |
| 306 | (TRF7970A_IRQ_STATUS_COL | \ |
| 307 | TRF7970A_IRQ_STATUS_FRAMING_EOF_ERROR | \ |
| 308 | TRF7970A_IRQ_STATUS_PARITY_ERROR | \ |
| 309 | TRF7970A_IRQ_STATUS_CRC_ERROR) |
| 310 | |
| 311 | #define TRF7970A_RSSI_OSC_STATUS_RSSI_MASK (BIT(2) | BIT(1) | BIT(0)) |
| 312 | #define TRF7970A_RSSI_OSC_STATUS_RSSI_X_MASK (BIT(5) | BIT(4) | BIT(3)) |
| 313 | #define TRF7970A_RSSI_OSC_STATUS_RSSI_OSC_OK BIT(6) |
| 314 | |
| 315 | #define TRF7970A_SPECIAL_FCN_REG1_COL_7_6 BIT(0) |
| 316 | #define TRF7970A_SPECIAL_FCN_REG1_14_ANTICOLL BIT(1) |
| 317 | #define TRF7970A_SPECIAL_FCN_REG1_4_BIT_RX BIT(2) |
| 318 | #define TRF7970A_SPECIAL_FCN_REG1_SP_DIR_MODE BIT(3) |
| 319 | #define TRF7970A_SPECIAL_FCN_REG1_NEXT_SLOT_37US BIT(4) |
| 320 | #define TRF7970A_SPECIAL_FCN_REG1_PAR43 BIT(5) |
| 321 | |
| 322 | #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_124 (0x0 << 2) |
| 323 | #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_120 (0x1 << 2) |
| 324 | #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_112 (0x2 << 2) |
| 325 | #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_96 (0x3 << 2) |
| 326 | #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_4 0x0 |
| 327 | #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_8 0x1 |
| 328 | #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_16 0x2 |
| 329 | #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_32 0x3 |
| 330 | |
| 331 | #define TRF7970A_NFC_LOW_FIELD_LEVEL_RFDET(v) ((v) & 0x07) |
| 332 | #define TRF7970A_NFC_LOW_FIELD_LEVEL_CLEX_DIS BIT(7) |
| 333 | |
| 334 | #define TRF7970A_NFC_TARGET_LEVEL_RFDET(v) ((v) & 0x07) |
| 335 | #define TRF7970A_NFC_TARGET_LEVEL_HI_RF BIT(3) |
| 336 | #define TRF7970A_NFC_TARGET_LEVEL_SDD_EN BIT(5) |
| 337 | #define TRF7970A_NFC_TARGET_LEVEL_LD_S_4BYTES (0x0 << 6) |
| 338 | #define TRF7970A_NFC_TARGET_LEVEL_LD_S_7BYTES (0x1 << 6) |
| 339 | #define TRF7970A_NFC_TARGET_LEVEL_LD_S_10BYTES (0x2 << 6) |
| 340 | |
| 341 | #define TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_106 BIT(0) |
| 342 | #define TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_212 BIT(1) |
| 343 | #define TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_424 (BIT(0) | BIT(1)) |
| 344 | #define TRF79070A_NFC_TARGET_PROTOCOL_PAS_14443B BIT(2) |
| 345 | #define TRF79070A_NFC_TARGET_PROTOCOL_PAS_106 BIT(3) |
| 346 | #define TRF79070A_NFC_TARGET_PROTOCOL_FELICA BIT(4) |
| 347 | #define TRF79070A_NFC_TARGET_PROTOCOL_RF_L BIT(6) |
| 348 | #define TRF79070A_NFC_TARGET_PROTOCOL_RF_H BIT(7) |
| 349 | |
| 350 | #define TRF79070A_NFC_TARGET_PROTOCOL_106A \ |
| 351 | (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \ |
| 352 | TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \ |
| 353 | TRF79070A_NFC_TARGET_PROTOCOL_PAS_106 | \ |
| 354 | TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_106) |
| 355 | |
| 356 | #define TRF79070A_NFC_TARGET_PROTOCOL_106B \ |
| 357 | (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \ |
| 358 | TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \ |
| 359 | TRF79070A_NFC_TARGET_PROTOCOL_PAS_14443B | \ |
| 360 | TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_106) |
| 361 | |
| 362 | #define TRF79070A_NFC_TARGET_PROTOCOL_212F \ |
| 363 | (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \ |
| 364 | TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \ |
| 365 | TRF79070A_NFC_TARGET_PROTOCOL_FELICA | \ |
| 366 | TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_212) |
| 367 | |
| 368 | #define TRF79070A_NFC_TARGET_PROTOCOL_424F \ |
| 369 | (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \ |
| 370 | TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \ |
| 371 | TRF79070A_NFC_TARGET_PROTOCOL_FELICA | \ |
| 372 | TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_424) |
| 373 | |
| 374 | #define TRF7970A_FIFO_STATUS_OVERFLOW BIT(7) |
| 375 | |
| 376 | /* NFC (ISO/IEC 14443A) Type 2 Tag commands */ |
| 377 | #define NFC_T2T_CMD_READ 0x30 |
| 378 | |
| 379 | /* ISO 15693 commands codes */ |
| 380 | #define ISO15693_CMD_INVENTORY 0x01 |
| 381 | #define ISO15693_CMD_READ_SINGLE_BLOCK 0x20 |
| 382 | #define ISO15693_CMD_WRITE_SINGLE_BLOCK 0x21 |
| 383 | #define ISO15693_CMD_LOCK_BLOCK 0x22 |
| 384 | #define ISO15693_CMD_READ_MULTIPLE_BLOCK 0x23 |
| 385 | #define ISO15693_CMD_WRITE_MULTIPLE_BLOCK 0x24 |
| 386 | #define ISO15693_CMD_SELECT 0x25 |
| 387 | #define ISO15693_CMD_RESET_TO_READY 0x26 |
| 388 | #define ISO15693_CMD_WRITE_AFI 0x27 |
| 389 | #define ISO15693_CMD_LOCK_AFI 0x28 |
| 390 | #define ISO15693_CMD_WRITE_DSFID 0x29 |
| 391 | #define ISO15693_CMD_LOCK_DSFID 0x2a |
| 392 | #define ISO15693_CMD_GET_SYSTEM_INFO 0x2b |
| 393 | #define ISO15693_CMD_GET_MULTIPLE_BLOCK_SECURITY_STATUS 0x2c |
| 394 | |
| 395 | /* ISO 15693 request and response flags */ |
| 396 | #define ISO15693_REQ_FLAG_SUB_CARRIER BIT(0) |
| 397 | #define ISO15693_REQ_FLAG_DATA_RATE BIT(1) |
| 398 | #define ISO15693_REQ_FLAG_INVENTORY BIT(2) |
| 399 | #define ISO15693_REQ_FLAG_PROTOCOL_EXT BIT(3) |
| 400 | #define ISO15693_REQ_FLAG_SELECT BIT(4) |
| 401 | #define ISO15693_REQ_FLAG_AFI BIT(4) |
| 402 | #define ISO15693_REQ_FLAG_ADDRESS BIT(5) |
| 403 | #define ISO15693_REQ_FLAG_NB_SLOTS BIT(5) |
| 404 | #define ISO15693_REQ_FLAG_OPTION BIT(6) |
| 405 | |
| 406 | #define ISO15693_REQ_FLAG_SPEED_MASK \ |
| 407 | (ISO15693_REQ_FLAG_SUB_CARRIER | ISO15693_REQ_FLAG_DATA_RATE) |
| 408 | |
| 409 | enum trf7970a_state { |
| 410 | TRF7970A_ST_PWR_OFF, |
| 411 | TRF7970A_ST_RF_OFF, |
| 412 | TRF7970A_ST_IDLE, |
| 413 | TRF7970A_ST_IDLE_RX_BLOCKED, |
| 414 | TRF7970A_ST_WAIT_FOR_TX_FIFO, |
| 415 | TRF7970A_ST_WAIT_FOR_RX_DATA, |
| 416 | TRF7970A_ST_WAIT_FOR_RX_DATA_CONT, |
| 417 | TRF7970A_ST_WAIT_TO_ISSUE_EOF, |
| 418 | TRF7970A_ST_LISTENING, |
| 419 | TRF7970A_ST_LISTENING_MD, |
| 420 | TRF7970A_ST_MAX |
| 421 | }; |
| 422 | |
| 423 | struct trf7970a { |
| 424 | enum trf7970a_state state; |
| 425 | struct device *dev; |
| 426 | struct spi_device *spi; |
| 427 | struct regulator *vin_regulator; |
| 428 | struct regulator *vddio_regulator; |
| 429 | struct nfc_digital_dev *ddev; |
| 430 | u32 quirks; |
| 431 | bool is_initiator; |
| 432 | bool aborting; |
| 433 | struct sk_buff *tx_skb; |
| 434 | struct sk_buff *rx_skb; |
| 435 | nfc_digital_cmd_complete_t cb; |
| 436 | void *cb_arg; |
| 437 | u8 chip_status_ctrl; |
| 438 | u8 iso_ctrl; |
| 439 | u8 iso_ctrl_tech; |
| 440 | u8 modulator_sys_clk_ctrl; |
| 441 | u8 special_fcn_reg1; |
| 442 | u8 io_ctrl; |
| 443 | unsigned int guard_time; |
| 444 | int technology; |
| 445 | int framing; |
| 446 | u8 md_rf_tech; |
| 447 | u8 tx_cmd; |
| 448 | bool issue_eof; |
| 449 | struct gpio_desc *en_gpiod; |
| 450 | struct gpio_desc *en2_gpiod; |
| 451 | struct mutex lock; |
| 452 | unsigned int timeout; |
| 453 | bool ignore_timeout; |
| 454 | struct delayed_work timeout_work; |
| 455 | }; |
| 456 | |
| 457 | static int trf7970a_cmd(struct trf7970a *trf, u8 opcode) |
| 458 | { |
| 459 | u8 cmd = TRF7970A_CMD_BIT_CTRL | TRF7970A_CMD_BIT_OPCODE(opcode); |
| 460 | int ret; |
| 461 | |
| 462 | dev_dbg(trf->dev, "cmd: 0x%x\n", cmd); |
| 463 | |
| 464 | ret = spi_write(trf->spi, &cmd, 1); |
| 465 | if (ret) |
| 466 | dev_err(trf->dev, "%s - cmd: 0x%x, ret: %d\n", __func__, cmd, |
| 467 | ret); |
| 468 | return ret; |
| 469 | } |
| 470 | |
| 471 | static int trf7970a_read(struct trf7970a *trf, u8 reg, u8 *val) |
| 472 | { |
| 473 | u8 addr = TRF7970A_CMD_BIT_RW | reg; |
| 474 | int ret; |
| 475 | |
| 476 | ret = spi_write_then_read(trf->spi, &addr, 1, val, 1); |
| 477 | if (ret) |
| 478 | dev_err(trf->dev, "%s - addr: 0x%x, ret: %d\n", __func__, addr, |
| 479 | ret); |
| 480 | |
| 481 | dev_dbg(trf->dev, "read(0x%x): 0x%x\n", addr, *val); |
| 482 | |
| 483 | return ret; |
| 484 | } |
| 485 | |
| 486 | static int trf7970a_read_cont(struct trf7970a *trf, u8 reg, u8 *buf, |
| 487 | size_t len) |
| 488 | { |
| 489 | u8 addr = reg | TRF7970A_CMD_BIT_RW | TRF7970A_CMD_BIT_CONTINUOUS; |
| 490 | struct spi_transfer t[2]; |
| 491 | struct spi_message m; |
| 492 | int ret; |
| 493 | |
| 494 | dev_dbg(trf->dev, "read_cont(0x%x, %zd)\n", addr, len); |
| 495 | |
| 496 | spi_message_init(&m); |
| 497 | |
| 498 | memset(&t, 0, sizeof(t)); |
| 499 | |
| 500 | t[0].tx_buf = &addr; |
| 501 | t[0].len = sizeof(addr); |
| 502 | spi_message_add_tail(&t[0], &m); |
| 503 | |
| 504 | t[1].rx_buf = buf; |
| 505 | t[1].len = len; |
| 506 | spi_message_add_tail(&t[1], &m); |
| 507 | |
| 508 | ret = spi_sync(trf->spi, &m); |
| 509 | if (ret) |
| 510 | dev_err(trf->dev, "%s - addr: 0x%x, ret: %d\n", __func__, addr, |
| 511 | ret); |
| 512 | return ret; |
| 513 | } |
| 514 | |
| 515 | static int trf7970a_write(struct trf7970a *trf, u8 reg, u8 val) |
| 516 | { |
| 517 | u8 buf[2] = { reg, val }; |
| 518 | int ret; |
| 519 | |
| 520 | dev_dbg(trf->dev, "write(0x%x): 0x%x\n", reg, val); |
| 521 | |
| 522 | ret = spi_write(trf->spi, buf, 2); |
| 523 | if (ret) |
| 524 | dev_err(trf->dev, "%s - write: 0x%x 0x%x, ret: %d\n", __func__, |
| 525 | buf[0], buf[1], ret); |
| 526 | |
| 527 | return ret; |
| 528 | } |
| 529 | |
| 530 | static int trf7970a_read_irqstatus(struct trf7970a *trf, u8 *status) |
| 531 | { |
| 532 | int ret; |
| 533 | u8 buf[2]; |
| 534 | u8 addr; |
| 535 | |
| 536 | addr = TRF7970A_IRQ_STATUS | TRF7970A_CMD_BIT_RW; |
| 537 | |
| 538 | if (trf->quirks & TRF7970A_QUIRK_IRQ_STATUS_READ) { |
| 539 | addr |= TRF7970A_CMD_BIT_CONTINUOUS; |
| 540 | ret = spi_write_then_read(trf->spi, &addr, 1, buf, 2); |
| 541 | } else { |
| 542 | ret = spi_write_then_read(trf->spi, &addr, 1, buf, 1); |
| 543 | } |
| 544 | |
| 545 | if (ret) |
| 546 | dev_err(trf->dev, "%s - irqstatus: Status read failed: %d\n", |
| 547 | __func__, ret); |
| 548 | else |
| 549 | *status = buf[0]; |
| 550 | |
| 551 | return ret; |
| 552 | } |
| 553 | |
| 554 | static int trf7970a_read_target_proto(struct trf7970a *trf, u8 *target_proto) |
| 555 | { |
| 556 | int ret; |
| 557 | u8 buf[2]; |
| 558 | u8 addr; |
| 559 | |
| 560 | addr = TRF79070A_NFC_TARGET_PROTOCOL | TRF7970A_CMD_BIT_RW | |
| 561 | TRF7970A_CMD_BIT_CONTINUOUS; |
| 562 | |
| 563 | ret = spi_write_then_read(trf->spi, &addr, 1, buf, 2); |
| 564 | if (ret) |
| 565 | dev_err(trf->dev, "%s - target_proto: Read failed: %d\n", |
| 566 | __func__, ret); |
| 567 | else |
| 568 | *target_proto = buf[0]; |
| 569 | |
| 570 | return ret; |
| 571 | } |
| 572 | |
| 573 | static int trf7970a_mode_detect(struct trf7970a *trf, u8 *rf_tech) |
| 574 | { |
| 575 | int ret; |
| 576 | u8 target_proto, tech; |
| 577 | |
| 578 | ret = trf7970a_read_target_proto(trf, &target_proto); |
| 579 | if (ret) |
| 580 | return ret; |
| 581 | |
| 582 | switch (target_proto) { |
| 583 | case TRF79070A_NFC_TARGET_PROTOCOL_106A: |
| 584 | tech = NFC_DIGITAL_RF_TECH_106A; |
| 585 | break; |
| 586 | case TRF79070A_NFC_TARGET_PROTOCOL_106B: |
| 587 | tech = NFC_DIGITAL_RF_TECH_106B; |
| 588 | break; |
| 589 | case TRF79070A_NFC_TARGET_PROTOCOL_212F: |
| 590 | tech = NFC_DIGITAL_RF_TECH_212F; |
| 591 | break; |
| 592 | case TRF79070A_NFC_TARGET_PROTOCOL_424F: |
| 593 | tech = NFC_DIGITAL_RF_TECH_424F; |
| 594 | break; |
| 595 | default: |
| 596 | dev_dbg(trf->dev, "%s - mode_detect: target_proto: 0x%x\n", |
| 597 | __func__, target_proto); |
| 598 | return -EIO; |
| 599 | } |
| 600 | |
| 601 | *rf_tech = tech; |
| 602 | |
| 603 | return ret; |
| 604 | } |
| 605 | |
| 606 | static void trf7970a_send_upstream(struct trf7970a *trf) |
| 607 | { |
| 608 | dev_kfree_skb_any(trf->tx_skb); |
| 609 | trf->tx_skb = NULL; |
| 610 | |
| 611 | if (trf->rx_skb && !IS_ERR(trf->rx_skb) && !trf->aborting) |
| 612 | print_hex_dump_debug("trf7970a rx data: ", DUMP_PREFIX_NONE, |
| 613 | 16, 1, trf->rx_skb->data, trf->rx_skb->len, |
| 614 | false); |
| 615 | |
| 616 | trf->state = TRF7970A_ST_IDLE; |
| 617 | |
| 618 | if (trf->aborting) { |
| 619 | dev_dbg(trf->dev, "Abort process complete\n"); |
| 620 | |
| 621 | if (!IS_ERR(trf->rx_skb)) { |
| 622 | kfree_skb(trf->rx_skb); |
| 623 | trf->rx_skb = ERR_PTR(-ECANCELED); |
| 624 | } |
| 625 | |
| 626 | trf->aborting = false; |
| 627 | } |
| 628 | |
| 629 | trf->cb(trf->ddev, trf->cb_arg, trf->rx_skb); |
| 630 | |
| 631 | trf->rx_skb = NULL; |
| 632 | } |
| 633 | |
| 634 | static void trf7970a_send_err_upstream(struct trf7970a *trf, int errno) |
| 635 | { |
| 636 | dev_dbg(trf->dev, "Error - state: %d, errno: %d\n", trf->state, errno); |
| 637 | |
| 638 | cancel_delayed_work(&trf->timeout_work); |
| 639 | |
| 640 | kfree_skb(trf->rx_skb); |
| 641 | trf->rx_skb = ERR_PTR(errno); |
| 642 | |
| 643 | trf7970a_send_upstream(trf); |
| 644 | } |
| 645 | |
| 646 | static int trf7970a_transmit(struct trf7970a *trf, struct sk_buff *skb, |
| 647 | unsigned int len, const u8 *prefix, |
| 648 | unsigned int prefix_len) |
| 649 | { |
| 650 | struct spi_transfer t[2]; |
| 651 | struct spi_message m; |
| 652 | unsigned int timeout; |
| 653 | int ret; |
| 654 | |
| 655 | print_hex_dump_debug("trf7970a tx data: ", DUMP_PREFIX_NONE, |
| 656 | 16, 1, skb->data, len, false); |
| 657 | |
| 658 | spi_message_init(&m); |
| 659 | |
| 660 | memset(&t, 0, sizeof(t)); |
| 661 | |
| 662 | t[0].tx_buf = prefix; |
| 663 | t[0].len = prefix_len; |
| 664 | spi_message_add_tail(&t[0], &m); |
| 665 | |
| 666 | t[1].tx_buf = skb->data; |
| 667 | t[1].len = len; |
| 668 | spi_message_add_tail(&t[1], &m); |
| 669 | |
| 670 | ret = spi_sync(trf->spi, &m); |
| 671 | if (ret) { |
| 672 | dev_err(trf->dev, "%s - Can't send tx data: %d\n", __func__, |
| 673 | ret); |
| 674 | return ret; |
| 675 | } |
| 676 | |
| 677 | skb_pull(skb, len); |
| 678 | |
| 679 | if (skb->len > 0) { |
| 680 | trf->state = TRF7970A_ST_WAIT_FOR_TX_FIFO; |
| 681 | timeout = TRF7970A_WAIT_FOR_FIFO_DRAIN_TIMEOUT; |
| 682 | } else { |
| 683 | if (trf->issue_eof) { |
| 684 | trf->state = TRF7970A_ST_WAIT_TO_ISSUE_EOF; |
| 685 | timeout = TRF7970A_WAIT_TO_ISSUE_ISO15693_EOF; |
| 686 | } else { |
| 687 | trf->state = TRF7970A_ST_WAIT_FOR_RX_DATA; |
| 688 | |
| 689 | if (!trf->timeout) |
| 690 | timeout = TRF7970A_WAIT_FOR_TX_IRQ; |
| 691 | else |
| 692 | timeout = trf->timeout; |
| 693 | } |
| 694 | } |
| 695 | |
| 696 | dev_dbg(trf->dev, "Setting timeout for %d ms, state: %d\n", timeout, |
| 697 | trf->state); |
| 698 | |
| 699 | schedule_delayed_work(&trf->timeout_work, msecs_to_jiffies(timeout)); |
| 700 | |
| 701 | return 0; |
| 702 | } |
| 703 | |
| 704 | static void trf7970a_fill_fifo(struct trf7970a *trf) |
| 705 | { |
| 706 | struct sk_buff *skb = trf->tx_skb; |
| 707 | unsigned int len; |
| 708 | int ret; |
| 709 | u8 fifo_bytes; |
| 710 | u8 prefix; |
| 711 | |
| 712 | ret = trf7970a_read(trf, TRF7970A_FIFO_STATUS, &fifo_bytes); |
| 713 | if (ret) { |
| 714 | trf7970a_send_err_upstream(trf, ret); |
| 715 | return; |
| 716 | } |
| 717 | |
| 718 | dev_dbg(trf->dev, "Filling FIFO - fifo_bytes: 0x%x\n", fifo_bytes); |
| 719 | |
| 720 | fifo_bytes &= ~TRF7970A_FIFO_STATUS_OVERFLOW; |
| 721 | |
| 722 | /* Calculate how much more data can be written to the fifo */ |
| 723 | len = TRF7970A_FIFO_SIZE - fifo_bytes; |
| 724 | if (!len) { |
| 725 | schedule_delayed_work(&trf->timeout_work, |
| 726 | msecs_to_jiffies(TRF7970A_WAIT_FOR_FIFO_DRAIN_TIMEOUT)); |
| 727 | return; |
| 728 | } |
| 729 | |
| 730 | len = min(skb->len, len); |
| 731 | |
| 732 | prefix = TRF7970A_CMD_BIT_CONTINUOUS | TRF7970A_FIFO_IO_REGISTER; |
| 733 | |
| 734 | ret = trf7970a_transmit(trf, skb, len, &prefix, sizeof(prefix)); |
| 735 | if (ret) |
| 736 | trf7970a_send_err_upstream(trf, ret); |
| 737 | } |
| 738 | |
| 739 | static void trf7970a_drain_fifo(struct trf7970a *trf, u8 status) |
| 740 | { |
| 741 | struct sk_buff *skb = trf->rx_skb; |
| 742 | int ret; |
| 743 | u8 fifo_bytes; |
| 744 | |
| 745 | if (status & TRF7970A_IRQ_STATUS_ERROR) { |
| 746 | trf7970a_send_err_upstream(trf, -EIO); |
| 747 | return; |
| 748 | } |
| 749 | |
| 750 | ret = trf7970a_read(trf, TRF7970A_FIFO_STATUS, &fifo_bytes); |
| 751 | if (ret) { |
| 752 | trf7970a_send_err_upstream(trf, ret); |
| 753 | return; |
| 754 | } |
| 755 | |
| 756 | dev_dbg(trf->dev, "Draining FIFO - fifo_bytes: 0x%x\n", fifo_bytes); |
| 757 | |
| 758 | fifo_bytes &= ~TRF7970A_FIFO_STATUS_OVERFLOW; |
| 759 | |
| 760 | if (!fifo_bytes) |
| 761 | goto no_rx_data; |
| 762 | |
| 763 | if (fifo_bytes > skb_tailroom(skb)) { |
| 764 | skb = skb_copy_expand(skb, skb_headroom(skb), |
| 765 | max_t(int, fifo_bytes, |
| 766 | TRF7970A_RX_SKB_ALLOC_SIZE), |
| 767 | GFP_KERNEL); |
| 768 | if (!skb) { |
| 769 | trf7970a_send_err_upstream(trf, -ENOMEM); |
| 770 | return; |
| 771 | } |
| 772 | |
| 773 | kfree_skb(trf->rx_skb); |
| 774 | trf->rx_skb = skb; |
| 775 | } |
| 776 | |
| 777 | ret = trf7970a_read_cont(trf, TRF7970A_FIFO_IO_REGISTER, |
| 778 | skb_put(skb, fifo_bytes), fifo_bytes); |
| 779 | if (ret) { |
| 780 | trf7970a_send_err_upstream(trf, ret); |
| 781 | return; |
| 782 | } |
| 783 | |
| 784 | /* If received Type 2 ACK/NACK, shift right 4 bits and pass up */ |
| 785 | if ((trf->framing == NFC_DIGITAL_FRAMING_NFCA_T2T) && (skb->len == 1) && |
| 786 | (trf->special_fcn_reg1 == TRF7970A_SPECIAL_FCN_REG1_4_BIT_RX)) { |
| 787 | skb->data[0] >>= 4; |
| 788 | status = TRF7970A_IRQ_STATUS_SRX; |
| 789 | } else { |
| 790 | trf->state = TRF7970A_ST_WAIT_FOR_RX_DATA_CONT; |
| 791 | |
| 792 | ret = trf7970a_read(trf, TRF7970A_FIFO_STATUS, &fifo_bytes); |
| 793 | if (ret) { |
| 794 | trf7970a_send_err_upstream(trf, ret); |
| 795 | return; |
| 796 | } |
| 797 | |
| 798 | fifo_bytes &= ~TRF7970A_FIFO_STATUS_OVERFLOW; |
| 799 | |
| 800 | /* If there are bytes in the FIFO, set status to '0' so |
| 801 | * the if stmt below doesn't fire and the driver will wait |
| 802 | * for the trf7970a to generate another RX interrupt. |
| 803 | */ |
| 804 | if (fifo_bytes) |
| 805 | status = 0; |
| 806 | } |
| 807 | |
| 808 | no_rx_data: |
| 809 | if (status == TRF7970A_IRQ_STATUS_SRX) { /* Receive complete */ |
| 810 | trf7970a_send_upstream(trf); |
| 811 | return; |
| 812 | } |
| 813 | |
| 814 | dev_dbg(trf->dev, "Setting timeout for %d ms\n", |
| 815 | TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT); |
| 816 | |
| 817 | schedule_delayed_work(&trf->timeout_work, |
| 818 | msecs_to_jiffies(TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT)); |
| 819 | } |
| 820 | |
| 821 | static irqreturn_t trf7970a_irq(int irq, void *dev_id) |
| 822 | { |
| 823 | struct trf7970a *trf = dev_id; |
| 824 | int ret; |
| 825 | u8 status, fifo_bytes, iso_ctrl; |
| 826 | |
| 827 | mutex_lock(&trf->lock); |
| 828 | |
| 829 | if (trf->state == TRF7970A_ST_RF_OFF) { |
| 830 | mutex_unlock(&trf->lock); |
| 831 | return IRQ_NONE; |
| 832 | } |
| 833 | |
| 834 | ret = trf7970a_read_irqstatus(trf, &status); |
| 835 | if (ret) { |
| 836 | mutex_unlock(&trf->lock); |
| 837 | return IRQ_NONE; |
| 838 | } |
| 839 | |
| 840 | dev_dbg(trf->dev, "IRQ - state: %d, status: 0x%x\n", trf->state, |
| 841 | status); |
| 842 | |
| 843 | if (!status) { |
| 844 | mutex_unlock(&trf->lock); |
| 845 | return IRQ_NONE; |
| 846 | } |
| 847 | |
| 848 | switch (trf->state) { |
| 849 | case TRF7970A_ST_IDLE: |
| 850 | case TRF7970A_ST_IDLE_RX_BLOCKED: |
| 851 | /* If initiator and getting interrupts caused by RF noise, |
| 852 | * turn off the receiver to avoid unnecessary interrupts. |
| 853 | * It will be turned back on in trf7970a_send_cmd() when |
| 854 | * the next command is issued. |
| 855 | */ |
| 856 | if (trf->is_initiator && (status & TRF7970A_IRQ_STATUS_ERROR)) { |
| 857 | trf7970a_cmd(trf, TRF7970A_CMD_BLOCK_RX); |
| 858 | trf->state = TRF7970A_ST_IDLE_RX_BLOCKED; |
| 859 | } |
| 860 | |
| 861 | trf7970a_cmd(trf, TRF7970A_CMD_FIFO_RESET); |
| 862 | break; |
| 863 | case TRF7970A_ST_WAIT_FOR_TX_FIFO: |
| 864 | if (status & TRF7970A_IRQ_STATUS_TX) { |
| 865 | trf->ignore_timeout = |
| 866 | !cancel_delayed_work(&trf->timeout_work); |
| 867 | trf7970a_fill_fifo(trf); |
| 868 | } else { |
| 869 | trf7970a_send_err_upstream(trf, -EIO); |
| 870 | } |
| 871 | break; |
| 872 | case TRF7970A_ST_WAIT_FOR_RX_DATA: |
| 873 | case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT: |
| 874 | if (status & TRF7970A_IRQ_STATUS_SRX) { |
| 875 | trf->ignore_timeout = |
| 876 | !cancel_delayed_work(&trf->timeout_work); |
| 877 | trf7970a_drain_fifo(trf, status); |
| 878 | } else if (status & TRF7970A_IRQ_STATUS_FIFO) { |
| 879 | ret = trf7970a_read(trf, TRF7970A_FIFO_STATUS, |
| 880 | &fifo_bytes); |
| 881 | |
| 882 | fifo_bytes &= ~TRF7970A_FIFO_STATUS_OVERFLOW; |
| 883 | |
| 884 | if (ret) |
| 885 | trf7970a_send_err_upstream(trf, ret); |
| 886 | else if (!fifo_bytes) |
| 887 | trf7970a_cmd(trf, TRF7970A_CMD_FIFO_RESET); |
| 888 | } else if ((status == TRF7970A_IRQ_STATUS_TX) || |
| 889 | (!trf->is_initiator && |
| 890 | (status == (TRF7970A_IRQ_STATUS_TX | |
| 891 | TRF7970A_IRQ_STATUS_NFC_RF)))) { |
| 892 | trf7970a_cmd(trf, TRF7970A_CMD_FIFO_RESET); |
| 893 | |
| 894 | if (!trf->timeout) { |
| 895 | trf->ignore_timeout = |
| 896 | !cancel_delayed_work(&trf->timeout_work); |
| 897 | trf->rx_skb = ERR_PTR(0); |
| 898 | trf7970a_send_upstream(trf); |
| 899 | break; |
| 900 | } |
| 901 | |
| 902 | if (trf->is_initiator) |
| 903 | break; |
| 904 | |
| 905 | iso_ctrl = trf->iso_ctrl; |
| 906 | |
| 907 | switch (trf->framing) { |
| 908 | case NFC_DIGITAL_FRAMING_NFCA_STANDARD: |
| 909 | trf->tx_cmd = TRF7970A_CMD_TRANSMIT_NO_CRC; |
| 910 | iso_ctrl |= TRF7970A_ISO_CTRL_RX_CRC_N; |
| 911 | trf->iso_ctrl = 0xff; /* Force ISO_CTRL write */ |
| 912 | break; |
| 913 | case NFC_DIGITAL_FRAMING_NFCA_STANDARD_WITH_CRC_A: |
| 914 | trf->tx_cmd = TRF7970A_CMD_TRANSMIT; |
| 915 | iso_ctrl &= ~TRF7970A_ISO_CTRL_RX_CRC_N; |
| 916 | trf->iso_ctrl = 0xff; /* Force ISO_CTRL write */ |
| 917 | break; |
| 918 | case NFC_DIGITAL_FRAMING_NFCA_ANTICOL_COMPLETE: |
| 919 | ret = trf7970a_write(trf, |
| 920 | TRF7970A_SPECIAL_FCN_REG1, |
| 921 | TRF7970A_SPECIAL_FCN_REG1_14_ANTICOLL); |
| 922 | if (ret) |
| 923 | goto err_unlock_exit; |
| 924 | |
| 925 | trf->special_fcn_reg1 = |
| 926 | TRF7970A_SPECIAL_FCN_REG1_14_ANTICOLL; |
| 927 | break; |
| 928 | default: |
| 929 | break; |
| 930 | } |
| 931 | |
| 932 | if (iso_ctrl != trf->iso_ctrl) { |
| 933 | ret = trf7970a_write(trf, TRF7970A_ISO_CTRL, |
| 934 | iso_ctrl); |
| 935 | if (ret) |
| 936 | goto err_unlock_exit; |
| 937 | |
| 938 | trf->iso_ctrl = iso_ctrl; |
| 939 | } |
| 940 | } else { |
| 941 | trf7970a_send_err_upstream(trf, -EIO); |
| 942 | } |
| 943 | break; |
| 944 | case TRF7970A_ST_WAIT_TO_ISSUE_EOF: |
| 945 | if (status != TRF7970A_IRQ_STATUS_TX) |
| 946 | trf7970a_send_err_upstream(trf, -EIO); |
| 947 | break; |
| 948 | case TRF7970A_ST_LISTENING: |
| 949 | if (status & TRF7970A_IRQ_STATUS_SRX) { |
| 950 | trf->ignore_timeout = |
| 951 | !cancel_delayed_work(&trf->timeout_work); |
| 952 | trf7970a_drain_fifo(trf, status); |
| 953 | } else if (!(status & TRF7970A_IRQ_STATUS_NFC_RF)) { |
| 954 | trf7970a_send_err_upstream(trf, -EIO); |
| 955 | } |
| 956 | break; |
| 957 | case TRF7970A_ST_LISTENING_MD: |
| 958 | if (status & TRF7970A_IRQ_STATUS_SRX) { |
| 959 | trf->ignore_timeout = |
| 960 | !cancel_delayed_work(&trf->timeout_work); |
| 961 | |
| 962 | ret = trf7970a_mode_detect(trf, &trf->md_rf_tech); |
| 963 | if (ret) { |
| 964 | trf7970a_send_err_upstream(trf, ret); |
| 965 | } else { |
| 966 | trf->state = TRF7970A_ST_LISTENING; |
| 967 | trf7970a_drain_fifo(trf, status); |
| 968 | } |
| 969 | } else if (!(status & TRF7970A_IRQ_STATUS_NFC_RF)) { |
| 970 | trf7970a_send_err_upstream(trf, -EIO); |
| 971 | } |
| 972 | break; |
| 973 | default: |
| 974 | dev_err(trf->dev, "%s - Driver in invalid state: %d\n", |
| 975 | __func__, trf->state); |
| 976 | } |
| 977 | |
| 978 | err_unlock_exit: |
| 979 | mutex_unlock(&trf->lock); |
| 980 | return IRQ_HANDLED; |
| 981 | } |
| 982 | |
| 983 | static void trf7970a_issue_eof(struct trf7970a *trf) |
| 984 | { |
| 985 | int ret; |
| 986 | |
| 987 | dev_dbg(trf->dev, "Issuing EOF\n"); |
| 988 | |
| 989 | ret = trf7970a_cmd(trf, TRF7970A_CMD_FIFO_RESET); |
| 990 | if (ret) |
| 991 | trf7970a_send_err_upstream(trf, ret); |
| 992 | |
| 993 | ret = trf7970a_cmd(trf, TRF7970A_CMD_EOF); |
| 994 | if (ret) |
| 995 | trf7970a_send_err_upstream(trf, ret); |
| 996 | |
| 997 | trf->state = TRF7970A_ST_WAIT_FOR_RX_DATA; |
| 998 | |
| 999 | dev_dbg(trf->dev, "Setting timeout for %d ms, state: %d\n", |
| 1000 | trf->timeout, trf->state); |
| 1001 | |
| 1002 | schedule_delayed_work(&trf->timeout_work, |
| 1003 | msecs_to_jiffies(trf->timeout)); |
| 1004 | } |
| 1005 | |
| 1006 | static void trf7970a_timeout_work_handler(struct work_struct *work) |
| 1007 | { |
| 1008 | struct trf7970a *trf = container_of(work, struct trf7970a, |
| 1009 | timeout_work.work); |
| 1010 | |
| 1011 | dev_dbg(trf->dev, "Timeout - state: %d, ignore_timeout: %d\n", |
| 1012 | trf->state, trf->ignore_timeout); |
| 1013 | |
| 1014 | mutex_lock(&trf->lock); |
| 1015 | |
| 1016 | if (trf->ignore_timeout) |
| 1017 | trf->ignore_timeout = false; |
| 1018 | else if (trf->state == TRF7970A_ST_WAIT_FOR_RX_DATA_CONT) |
| 1019 | trf7970a_drain_fifo(trf, TRF7970A_IRQ_STATUS_SRX); |
| 1020 | else if (trf->state == TRF7970A_ST_WAIT_TO_ISSUE_EOF) |
| 1021 | trf7970a_issue_eof(trf); |
| 1022 | else |
| 1023 | trf7970a_send_err_upstream(trf, -ETIMEDOUT); |
| 1024 | |
| 1025 | mutex_unlock(&trf->lock); |
| 1026 | } |
| 1027 | |
| 1028 | static int trf7970a_init(struct trf7970a *trf) |
| 1029 | { |
| 1030 | int ret; |
| 1031 | |
| 1032 | dev_dbg(trf->dev, "Initializing device - state: %d\n", trf->state); |
| 1033 | |
| 1034 | ret = trf7970a_cmd(trf, TRF7970A_CMD_SOFT_INIT); |
| 1035 | if (ret) |
| 1036 | goto err_out; |
| 1037 | |
| 1038 | ret = trf7970a_cmd(trf, TRF7970A_CMD_IDLE); |
| 1039 | if (ret) |
| 1040 | goto err_out; |
| 1041 | |
| 1042 | ret = trf7970a_write(trf, TRF7970A_REG_IO_CTRL, |
| 1043 | trf->io_ctrl | TRF7970A_REG_IO_CTRL_VRS(0x1)); |
| 1044 | if (ret) |
| 1045 | goto err_out; |
| 1046 | |
| 1047 | ret = trf7970a_write(trf, TRF7970A_NFC_TARGET_LEVEL, 0); |
| 1048 | if (ret) |
| 1049 | goto err_out; |
| 1050 | |
| 1051 | usleep_range(1000, 2000); |
| 1052 | |
| 1053 | trf->chip_status_ctrl &= ~TRF7970A_CHIP_STATUS_RF_ON; |
| 1054 | |
| 1055 | ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL, |
| 1056 | trf->modulator_sys_clk_ctrl); |
| 1057 | if (ret) |
| 1058 | goto err_out; |
| 1059 | |
| 1060 | ret = trf7970a_write(trf, TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS, |
| 1061 | TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_96 | |
| 1062 | TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_32); |
| 1063 | if (ret) |
| 1064 | goto err_out; |
| 1065 | |
| 1066 | ret = trf7970a_write(trf, TRF7970A_SPECIAL_FCN_REG1, 0); |
| 1067 | if (ret) |
| 1068 | goto err_out; |
| 1069 | |
| 1070 | trf->special_fcn_reg1 = 0; |
| 1071 | |
| 1072 | trf->iso_ctrl = 0xff; |
| 1073 | return 0; |
| 1074 | |
| 1075 | err_out: |
| 1076 | dev_dbg(trf->dev, "Couldn't init device: %d\n", ret); |
| 1077 | return ret; |
| 1078 | } |
| 1079 | |
| 1080 | static void trf7970a_switch_rf_off(struct trf7970a *trf) |
| 1081 | { |
| 1082 | if ((trf->state == TRF7970A_ST_PWR_OFF) || |
| 1083 | (trf->state == TRF7970A_ST_RF_OFF)) |
| 1084 | return; |
| 1085 | |
| 1086 | dev_dbg(trf->dev, "Switching rf off\n"); |
| 1087 | |
| 1088 | trf->chip_status_ctrl &= ~TRF7970A_CHIP_STATUS_RF_ON; |
| 1089 | |
| 1090 | trf7970a_write(trf, TRF7970A_CHIP_STATUS_CTRL, trf->chip_status_ctrl); |
| 1091 | |
| 1092 | trf->aborting = false; |
| 1093 | trf->state = TRF7970A_ST_RF_OFF; |
| 1094 | |
| 1095 | pm_runtime_mark_last_busy(trf->dev); |
| 1096 | pm_runtime_put_autosuspend(trf->dev); |
| 1097 | } |
| 1098 | |
| 1099 | static int trf7970a_switch_rf_on(struct trf7970a *trf) |
| 1100 | { |
| 1101 | int ret; |
| 1102 | |
| 1103 | dev_dbg(trf->dev, "Switching rf on\n"); |
| 1104 | |
| 1105 | pm_runtime_get_sync(trf->dev); |
| 1106 | |
| 1107 | if (trf->state != TRF7970A_ST_RF_OFF) { /* Power on, RF off */ |
| 1108 | dev_err(trf->dev, "%s - Incorrect state: %d\n", __func__, |
| 1109 | trf->state); |
| 1110 | return -EINVAL; |
| 1111 | } |
| 1112 | |
| 1113 | ret = trf7970a_init(trf); |
| 1114 | if (ret) { |
| 1115 | dev_err(trf->dev, "%s - Can't initialize: %d\n", __func__, ret); |
| 1116 | return ret; |
| 1117 | } |
| 1118 | |
| 1119 | trf->state = TRF7970A_ST_IDLE; |
| 1120 | |
| 1121 | return 0; |
| 1122 | } |
| 1123 | |
| 1124 | static int trf7970a_switch_rf(struct nfc_digital_dev *ddev, bool on) |
| 1125 | { |
| 1126 | struct trf7970a *trf = nfc_digital_get_drvdata(ddev); |
| 1127 | int ret = 0; |
| 1128 | |
| 1129 | dev_dbg(trf->dev, "Switching RF - state: %d, on: %d\n", trf->state, on); |
| 1130 | |
| 1131 | mutex_lock(&trf->lock); |
| 1132 | |
| 1133 | if (on) { |
| 1134 | switch (trf->state) { |
| 1135 | case TRF7970A_ST_PWR_OFF: |
| 1136 | case TRF7970A_ST_RF_OFF: |
| 1137 | ret = trf7970a_switch_rf_on(trf); |
| 1138 | break; |
| 1139 | case TRF7970A_ST_IDLE: |
| 1140 | case TRF7970A_ST_IDLE_RX_BLOCKED: |
| 1141 | break; |
| 1142 | default: |
| 1143 | dev_err(trf->dev, "%s - Invalid request: %d %d\n", |
| 1144 | __func__, trf->state, on); |
| 1145 | trf7970a_switch_rf_off(trf); |
| 1146 | ret = -EINVAL; |
| 1147 | } |
| 1148 | } else { |
| 1149 | switch (trf->state) { |
| 1150 | case TRF7970A_ST_PWR_OFF: |
| 1151 | case TRF7970A_ST_RF_OFF: |
| 1152 | break; |
| 1153 | default: |
| 1154 | dev_err(trf->dev, "%s - Invalid request: %d %d\n", |
| 1155 | __func__, trf->state, on); |
| 1156 | ret = -EINVAL; |
| 1157 | fallthrough; |
| 1158 | case TRF7970A_ST_IDLE: |
| 1159 | case TRF7970A_ST_IDLE_RX_BLOCKED: |
| 1160 | case TRF7970A_ST_WAIT_FOR_RX_DATA: |
| 1161 | case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT: |
| 1162 | trf7970a_switch_rf_off(trf); |
| 1163 | } |
| 1164 | } |
| 1165 | |
| 1166 | mutex_unlock(&trf->lock); |
| 1167 | return ret; |
| 1168 | } |
| 1169 | |
| 1170 | static int trf7970a_in_config_rf_tech(struct trf7970a *trf, int tech) |
| 1171 | { |
| 1172 | int ret = 0; |
| 1173 | |
| 1174 | dev_dbg(trf->dev, "rf technology: %d\n", tech); |
| 1175 | |
| 1176 | switch (tech) { |
| 1177 | case NFC_DIGITAL_RF_TECH_106A: |
| 1178 | trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443A_106; |
| 1179 | trf->modulator_sys_clk_ctrl = |
| 1180 | (trf->modulator_sys_clk_ctrl & 0xf8) | |
| 1181 | TRF7970A_MODULATOR_DEPTH_OOK; |
| 1182 | trf->guard_time = TRF7970A_GUARD_TIME_NFCA; |
| 1183 | break; |
| 1184 | case NFC_DIGITAL_RF_TECH_106B: |
| 1185 | trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_14443B_106; |
| 1186 | trf->modulator_sys_clk_ctrl = |
| 1187 | (trf->modulator_sys_clk_ctrl & 0xf8) | |
| 1188 | TRF7970A_MODULATOR_DEPTH_ASK10; |
| 1189 | trf->guard_time = TRF7970A_GUARD_TIME_NFCB; |
| 1190 | break; |
| 1191 | case NFC_DIGITAL_RF_TECH_212F: |
| 1192 | trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_FELICA_212; |
| 1193 | trf->modulator_sys_clk_ctrl = |
| 1194 | (trf->modulator_sys_clk_ctrl & 0xf8) | |
| 1195 | TRF7970A_MODULATOR_DEPTH_ASK10; |
| 1196 | trf->guard_time = TRF7970A_GUARD_TIME_NFCF; |
| 1197 | break; |
| 1198 | case NFC_DIGITAL_RF_TECH_424F: |
| 1199 | trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_FELICA_424; |
| 1200 | trf->modulator_sys_clk_ctrl = |
| 1201 | (trf->modulator_sys_clk_ctrl & 0xf8) | |
| 1202 | TRF7970A_MODULATOR_DEPTH_ASK10; |
| 1203 | trf->guard_time = TRF7970A_GUARD_TIME_NFCF; |
| 1204 | break; |
| 1205 | case NFC_DIGITAL_RF_TECH_ISO15693: |
| 1206 | trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648; |
| 1207 | trf->modulator_sys_clk_ctrl = |
| 1208 | (trf->modulator_sys_clk_ctrl & 0xf8) | |
| 1209 | TRF7970A_MODULATOR_DEPTH_OOK; |
| 1210 | trf->guard_time = TRF7970A_GUARD_TIME_15693; |
| 1211 | break; |
| 1212 | default: |
| 1213 | dev_dbg(trf->dev, "Unsupported rf technology: %d\n", tech); |
| 1214 | return -EINVAL; |
| 1215 | } |
| 1216 | |
| 1217 | trf->technology = tech; |
| 1218 | |
| 1219 | /* If in initiator mode and not changing the RF tech due to a |
| 1220 | * PSL sequence (indicated by 'trf->iso_ctrl == 0xff' from |
| 1221 | * trf7970a_init()), clear the NFC Target Detection Level register |
| 1222 | * due to erratum. |
| 1223 | */ |
| 1224 | if (trf->iso_ctrl == 0xff) |
| 1225 | ret = trf7970a_write(trf, TRF7970A_NFC_TARGET_LEVEL, 0); |
| 1226 | |
| 1227 | return ret; |
| 1228 | } |
| 1229 | |
| 1230 | static int trf7970a_is_rf_field(struct trf7970a *trf, bool *is_rf_field) |
| 1231 | { |
| 1232 | int ret; |
| 1233 | u8 rssi; |
| 1234 | |
| 1235 | ret = trf7970a_write(trf, TRF7970A_CHIP_STATUS_CTRL, |
| 1236 | trf->chip_status_ctrl | |
| 1237 | TRF7970A_CHIP_STATUS_REC_ON); |
| 1238 | if (ret) |
| 1239 | return ret; |
| 1240 | |
| 1241 | ret = trf7970a_cmd(trf, TRF7970A_CMD_TEST_EXT_RF); |
| 1242 | if (ret) |
| 1243 | return ret; |
| 1244 | |
| 1245 | usleep_range(50, 60); |
| 1246 | |
| 1247 | ret = trf7970a_read(trf, TRF7970A_RSSI_OSC_STATUS, &rssi); |
| 1248 | if (ret) |
| 1249 | return ret; |
| 1250 | |
| 1251 | ret = trf7970a_write(trf, TRF7970A_CHIP_STATUS_CTRL, |
| 1252 | trf->chip_status_ctrl); |
| 1253 | if (ret) |
| 1254 | return ret; |
| 1255 | |
| 1256 | if (rssi & TRF7970A_RSSI_OSC_STATUS_RSSI_MASK) |
| 1257 | *is_rf_field = true; |
| 1258 | else |
| 1259 | *is_rf_field = false; |
| 1260 | |
| 1261 | return 0; |
| 1262 | } |
| 1263 | |
| 1264 | static int trf7970a_in_config_framing(struct trf7970a *trf, int framing) |
| 1265 | { |
| 1266 | u8 iso_ctrl = trf->iso_ctrl_tech; |
| 1267 | bool is_rf_field = false; |
| 1268 | int ret; |
| 1269 | |
| 1270 | dev_dbg(trf->dev, "framing: %d\n", framing); |
| 1271 | |
| 1272 | switch (framing) { |
| 1273 | case NFC_DIGITAL_FRAMING_NFCA_SHORT: |
| 1274 | case NFC_DIGITAL_FRAMING_NFCA_STANDARD: |
| 1275 | trf->tx_cmd = TRF7970A_CMD_TRANSMIT_NO_CRC; |
| 1276 | iso_ctrl |= TRF7970A_ISO_CTRL_RX_CRC_N; |
| 1277 | break; |
| 1278 | case NFC_DIGITAL_FRAMING_NFCA_STANDARD_WITH_CRC_A: |
| 1279 | case NFC_DIGITAL_FRAMING_NFCA_T4T: |
| 1280 | case NFC_DIGITAL_FRAMING_NFCB: |
| 1281 | case NFC_DIGITAL_FRAMING_NFCB_T4T: |
| 1282 | case NFC_DIGITAL_FRAMING_NFCF: |
| 1283 | case NFC_DIGITAL_FRAMING_NFCF_T3T: |
| 1284 | case NFC_DIGITAL_FRAMING_ISO15693_INVENTORY: |
| 1285 | case NFC_DIGITAL_FRAMING_ISO15693_T5T: |
| 1286 | case NFC_DIGITAL_FRAMING_NFCA_NFC_DEP: |
| 1287 | case NFC_DIGITAL_FRAMING_NFCF_NFC_DEP: |
| 1288 | trf->tx_cmd = TRF7970A_CMD_TRANSMIT; |
| 1289 | iso_ctrl &= ~TRF7970A_ISO_CTRL_RX_CRC_N; |
| 1290 | break; |
| 1291 | case NFC_DIGITAL_FRAMING_NFCA_T2T: |
| 1292 | trf->tx_cmd = TRF7970A_CMD_TRANSMIT; |
| 1293 | iso_ctrl |= TRF7970A_ISO_CTRL_RX_CRC_N; |
| 1294 | break; |
| 1295 | default: |
| 1296 | dev_dbg(trf->dev, "Unsupported Framing: %d\n", framing); |
| 1297 | return -EINVAL; |
| 1298 | } |
| 1299 | |
| 1300 | trf->framing = framing; |
| 1301 | |
| 1302 | if (!(trf->chip_status_ctrl & TRF7970A_CHIP_STATUS_RF_ON)) { |
| 1303 | ret = trf7970a_is_rf_field(trf, &is_rf_field); |
| 1304 | if (ret) |
| 1305 | return ret; |
| 1306 | |
| 1307 | if (is_rf_field) |
| 1308 | return -EBUSY; |
| 1309 | } |
| 1310 | |
| 1311 | if (iso_ctrl != trf->iso_ctrl) { |
| 1312 | ret = trf7970a_write(trf, TRF7970A_ISO_CTRL, iso_ctrl); |
| 1313 | if (ret) |
| 1314 | return ret; |
| 1315 | |
| 1316 | trf->iso_ctrl = iso_ctrl; |
| 1317 | |
| 1318 | ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL, |
| 1319 | trf->modulator_sys_clk_ctrl); |
| 1320 | if (ret) |
| 1321 | return ret; |
| 1322 | } |
| 1323 | |
| 1324 | if (!(trf->chip_status_ctrl & TRF7970A_CHIP_STATUS_RF_ON)) { |
| 1325 | ret = trf7970a_write(trf, TRF7970A_CHIP_STATUS_CTRL, |
| 1326 | trf->chip_status_ctrl | |
| 1327 | TRF7970A_CHIP_STATUS_RF_ON); |
| 1328 | if (ret) |
| 1329 | return ret; |
| 1330 | |
| 1331 | trf->chip_status_ctrl |= TRF7970A_CHIP_STATUS_RF_ON; |
| 1332 | |
| 1333 | usleep_range(trf->guard_time, trf->guard_time + 1000); |
| 1334 | } |
| 1335 | |
| 1336 | return 0; |
| 1337 | } |
| 1338 | |
| 1339 | static int trf7970a_in_configure_hw(struct nfc_digital_dev *ddev, int type, |
| 1340 | int param) |
| 1341 | { |
| 1342 | struct trf7970a *trf = nfc_digital_get_drvdata(ddev); |
| 1343 | int ret; |
| 1344 | |
| 1345 | dev_dbg(trf->dev, "Configure hw - type: %d, param: %d\n", type, param); |
| 1346 | |
| 1347 | mutex_lock(&trf->lock); |
| 1348 | |
| 1349 | trf->is_initiator = true; |
| 1350 | |
| 1351 | if ((trf->state == TRF7970A_ST_PWR_OFF) || |
| 1352 | (trf->state == TRF7970A_ST_RF_OFF)) { |
| 1353 | ret = trf7970a_switch_rf_on(trf); |
| 1354 | if (ret) |
| 1355 | goto err_unlock; |
| 1356 | } |
| 1357 | |
| 1358 | switch (type) { |
| 1359 | case NFC_DIGITAL_CONFIG_RF_TECH: |
| 1360 | ret = trf7970a_in_config_rf_tech(trf, param); |
| 1361 | break; |
| 1362 | case NFC_DIGITAL_CONFIG_FRAMING: |
| 1363 | ret = trf7970a_in_config_framing(trf, param); |
| 1364 | break; |
| 1365 | default: |
| 1366 | dev_dbg(trf->dev, "Unknown type: %d\n", type); |
| 1367 | ret = -EINVAL; |
| 1368 | } |
| 1369 | |
| 1370 | err_unlock: |
| 1371 | mutex_unlock(&trf->lock); |
| 1372 | return ret; |
| 1373 | } |
| 1374 | |
| 1375 | static int trf7970a_is_iso15693_write_or_lock(u8 cmd) |
| 1376 | { |
| 1377 | switch (cmd) { |
| 1378 | case ISO15693_CMD_WRITE_SINGLE_BLOCK: |
| 1379 | case ISO15693_CMD_LOCK_BLOCK: |
| 1380 | case ISO15693_CMD_WRITE_MULTIPLE_BLOCK: |
| 1381 | case ISO15693_CMD_WRITE_AFI: |
| 1382 | case ISO15693_CMD_LOCK_AFI: |
| 1383 | case ISO15693_CMD_WRITE_DSFID: |
| 1384 | case ISO15693_CMD_LOCK_DSFID: |
| 1385 | return 1; |
| 1386 | default: |
| 1387 | return 0; |
| 1388 | } |
| 1389 | } |
| 1390 | |
| 1391 | static int trf7970a_per_cmd_config(struct trf7970a *trf, |
| 1392 | const struct sk_buff *skb) |
| 1393 | { |
| 1394 | const u8 *req = skb->data; |
| 1395 | u8 special_fcn_reg1, iso_ctrl; |
| 1396 | int ret; |
| 1397 | |
| 1398 | trf->issue_eof = false; |
| 1399 | |
| 1400 | /* When issuing Type 2 read command, make sure the '4_bit_RX' bit in |
| 1401 | * special functions register 1 is cleared; otherwise, its a write or |
| 1402 | * sector select command and '4_bit_RX' must be set. |
| 1403 | * |
| 1404 | * When issuing an ISO 15693 command, inspect the flags byte to see |
| 1405 | * what speed to use. Also, remember if the OPTION flag is set on |
| 1406 | * a Type 5 write or lock command so the driver will know that it |
| 1407 | * has to send an EOF in order to get a response. |
| 1408 | */ |
| 1409 | if ((trf->technology == NFC_DIGITAL_RF_TECH_106A) && |
| 1410 | (trf->framing == NFC_DIGITAL_FRAMING_NFCA_T2T)) { |
| 1411 | if (req[0] == NFC_T2T_CMD_READ) |
| 1412 | special_fcn_reg1 = 0; |
| 1413 | else |
| 1414 | special_fcn_reg1 = TRF7970A_SPECIAL_FCN_REG1_4_BIT_RX; |
| 1415 | |
| 1416 | if (special_fcn_reg1 != trf->special_fcn_reg1) { |
| 1417 | ret = trf7970a_write(trf, TRF7970A_SPECIAL_FCN_REG1, |
| 1418 | special_fcn_reg1); |
| 1419 | if (ret) |
| 1420 | return ret; |
| 1421 | |
| 1422 | trf->special_fcn_reg1 = special_fcn_reg1; |
| 1423 | } |
| 1424 | } else if (trf->technology == NFC_DIGITAL_RF_TECH_ISO15693) { |
| 1425 | iso_ctrl = trf->iso_ctrl & ~TRF7970A_ISO_CTRL_RFID_SPEED_MASK; |
| 1426 | |
| 1427 | switch (req[0] & ISO15693_REQ_FLAG_SPEED_MASK) { |
| 1428 | case 0x00: |
| 1429 | iso_ctrl |= TRF7970A_ISO_CTRL_15693_SGL_1OF4_662; |
| 1430 | break; |
| 1431 | case ISO15693_REQ_FLAG_SUB_CARRIER: |
| 1432 | iso_ctrl |= TRF7970A_ISO_CTRL_15693_DBL_1OF4_667a; |
| 1433 | break; |
| 1434 | case ISO15693_REQ_FLAG_DATA_RATE: |
| 1435 | iso_ctrl |= TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648; |
| 1436 | break; |
| 1437 | case (ISO15693_REQ_FLAG_SUB_CARRIER | |
| 1438 | ISO15693_REQ_FLAG_DATA_RATE): |
| 1439 | iso_ctrl |= TRF7970A_ISO_CTRL_15693_DBL_1OF4_2669; |
| 1440 | break; |
| 1441 | } |
| 1442 | |
| 1443 | if (iso_ctrl != trf->iso_ctrl) { |
| 1444 | ret = trf7970a_write(trf, TRF7970A_ISO_CTRL, iso_ctrl); |
| 1445 | if (ret) |
| 1446 | return ret; |
| 1447 | |
| 1448 | trf->iso_ctrl = iso_ctrl; |
| 1449 | } |
| 1450 | |
| 1451 | if ((trf->framing == NFC_DIGITAL_FRAMING_ISO15693_T5T) && |
| 1452 | trf7970a_is_iso15693_write_or_lock(req[1]) && |
| 1453 | (req[0] & ISO15693_REQ_FLAG_OPTION)) |
| 1454 | trf->issue_eof = true; |
| 1455 | } |
| 1456 | |
| 1457 | return 0; |
| 1458 | } |
| 1459 | |
| 1460 | static int trf7970a_send_cmd(struct nfc_digital_dev *ddev, |
| 1461 | struct sk_buff *skb, u16 timeout, |
| 1462 | nfc_digital_cmd_complete_t cb, void *arg) |
| 1463 | { |
| 1464 | struct trf7970a *trf = nfc_digital_get_drvdata(ddev); |
| 1465 | u8 prefix[5]; |
| 1466 | unsigned int len; |
| 1467 | int ret; |
| 1468 | u8 status; |
| 1469 | |
| 1470 | dev_dbg(trf->dev, "New request - state: %d, timeout: %d ms, len: %d\n", |
| 1471 | trf->state, timeout, skb->len); |
| 1472 | |
| 1473 | if (skb->len > TRF7970A_TX_MAX) |
| 1474 | return -EINVAL; |
| 1475 | |
| 1476 | mutex_lock(&trf->lock); |
| 1477 | |
| 1478 | if ((trf->state != TRF7970A_ST_IDLE) && |
| 1479 | (trf->state != TRF7970A_ST_IDLE_RX_BLOCKED)) { |
| 1480 | dev_err(trf->dev, "%s - Bogus state: %d\n", __func__, |
| 1481 | trf->state); |
| 1482 | ret = -EIO; |
| 1483 | goto out_err; |
| 1484 | } |
| 1485 | |
| 1486 | if (trf->aborting) { |
| 1487 | dev_dbg(trf->dev, "Abort process complete\n"); |
| 1488 | trf->aborting = false; |
| 1489 | ret = -ECANCELED; |
| 1490 | goto out_err; |
| 1491 | } |
| 1492 | |
| 1493 | if (timeout) { |
| 1494 | trf->rx_skb = nfc_alloc_recv_skb(TRF7970A_RX_SKB_ALLOC_SIZE, |
| 1495 | GFP_KERNEL); |
| 1496 | if (!trf->rx_skb) { |
| 1497 | dev_dbg(trf->dev, "Can't alloc rx_skb\n"); |
| 1498 | ret = -ENOMEM; |
| 1499 | goto out_err; |
| 1500 | } |
| 1501 | } |
| 1502 | |
| 1503 | if (trf->state == TRF7970A_ST_IDLE_RX_BLOCKED) { |
| 1504 | ret = trf7970a_cmd(trf, TRF7970A_CMD_ENABLE_RX); |
| 1505 | if (ret) |
| 1506 | goto out_err; |
| 1507 | |
| 1508 | trf->state = TRF7970A_ST_IDLE; |
| 1509 | } |
| 1510 | |
| 1511 | if (trf->is_initiator) { |
| 1512 | ret = trf7970a_per_cmd_config(trf, skb); |
| 1513 | if (ret) |
| 1514 | goto out_err; |
| 1515 | } |
| 1516 | |
| 1517 | trf->ddev = ddev; |
| 1518 | trf->tx_skb = skb; |
| 1519 | trf->cb = cb; |
| 1520 | trf->cb_arg = arg; |
| 1521 | trf->timeout = timeout; |
| 1522 | trf->ignore_timeout = false; |
| 1523 | |
| 1524 | len = skb->len; |
| 1525 | |
| 1526 | /* TX data must be prefixed with a FIFO reset cmd, a cmd that depends |
| 1527 | * on what the current framing is, the address of the TX length byte 1 |
| 1528 | * register (0x1d), and the 2 byte length of the data to be transmitted. |
| 1529 | * That totals 5 bytes. |
| 1530 | */ |
| 1531 | prefix[0] = TRF7970A_CMD_BIT_CTRL | |
| 1532 | TRF7970A_CMD_BIT_OPCODE(TRF7970A_CMD_FIFO_RESET); |
| 1533 | prefix[1] = TRF7970A_CMD_BIT_CTRL | |
| 1534 | TRF7970A_CMD_BIT_OPCODE(trf->tx_cmd); |
| 1535 | prefix[2] = TRF7970A_CMD_BIT_CONTINUOUS | TRF7970A_TX_LENGTH_BYTE1; |
| 1536 | |
| 1537 | if (trf->framing == NFC_DIGITAL_FRAMING_NFCA_SHORT) { |
| 1538 | prefix[3] = 0x00; |
| 1539 | prefix[4] = 0x0f; /* 7 bits */ |
| 1540 | } else { |
| 1541 | prefix[3] = (len & 0xf00) >> 4; |
| 1542 | prefix[3] |= ((len & 0xf0) >> 4); |
| 1543 | prefix[4] = ((len & 0x0f) << 4); |
| 1544 | } |
| 1545 | |
| 1546 | len = min_t(int, skb->len, TRF7970A_FIFO_SIZE); |
| 1547 | |
| 1548 | /* Clear possible spurious interrupt */ |
| 1549 | ret = trf7970a_read_irqstatus(trf, &status); |
| 1550 | if (ret) |
| 1551 | goto out_err; |
| 1552 | |
| 1553 | ret = trf7970a_transmit(trf, skb, len, prefix, sizeof(prefix)); |
| 1554 | if (ret) { |
| 1555 | kfree_skb(trf->rx_skb); |
| 1556 | trf->rx_skb = NULL; |
| 1557 | } |
| 1558 | |
| 1559 | out_err: |
| 1560 | mutex_unlock(&trf->lock); |
| 1561 | return ret; |
| 1562 | } |
| 1563 | |
| 1564 | static int trf7970a_tg_config_rf_tech(struct trf7970a *trf, int tech) |
| 1565 | { |
| 1566 | int ret = 0; |
| 1567 | |
| 1568 | dev_dbg(trf->dev, "rf technology: %d\n", tech); |
| 1569 | |
| 1570 | switch (tech) { |
| 1571 | case NFC_DIGITAL_RF_TECH_106A: |
| 1572 | trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE | |
| 1573 | TRF7970A_ISO_CTRL_NFC_CE | TRF7970A_ISO_CTRL_NFC_CE_14443A; |
| 1574 | trf->modulator_sys_clk_ctrl = |
| 1575 | (trf->modulator_sys_clk_ctrl & 0xf8) | |
| 1576 | TRF7970A_MODULATOR_DEPTH_OOK; |
| 1577 | break; |
| 1578 | case NFC_DIGITAL_RF_TECH_212F: |
| 1579 | trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE | |
| 1580 | TRF7970A_ISO_CTRL_NFC_NFCF_212; |
| 1581 | trf->modulator_sys_clk_ctrl = |
| 1582 | (trf->modulator_sys_clk_ctrl & 0xf8) | |
| 1583 | TRF7970A_MODULATOR_DEPTH_ASK10; |
| 1584 | break; |
| 1585 | case NFC_DIGITAL_RF_TECH_424F: |
| 1586 | trf->iso_ctrl_tech = TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE | |
| 1587 | TRF7970A_ISO_CTRL_NFC_NFCF_424; |
| 1588 | trf->modulator_sys_clk_ctrl = |
| 1589 | (trf->modulator_sys_clk_ctrl & 0xf8) | |
| 1590 | TRF7970A_MODULATOR_DEPTH_ASK10; |
| 1591 | break; |
| 1592 | default: |
| 1593 | dev_dbg(trf->dev, "Unsupported rf technology: %d\n", tech); |
| 1594 | return -EINVAL; |
| 1595 | } |
| 1596 | |
| 1597 | trf->technology = tech; |
| 1598 | |
| 1599 | /* Normally we write the ISO_CTRL register in |
| 1600 | * trf7970a_tg_config_framing() because the framing can change |
| 1601 | * the value written. However, when sending a PSL RES, |
| 1602 | * digital_tg_send_psl_res_complete() doesn't call |
| 1603 | * trf7970a_tg_config_framing() so we must write the register |
| 1604 | * here. |
| 1605 | */ |
| 1606 | if ((trf->framing == NFC_DIGITAL_FRAMING_NFC_DEP_ACTIVATED) && |
| 1607 | (trf->iso_ctrl_tech != trf->iso_ctrl)) { |
| 1608 | ret = trf7970a_write(trf, TRF7970A_ISO_CTRL, |
| 1609 | trf->iso_ctrl_tech); |
| 1610 | |
| 1611 | trf->iso_ctrl = trf->iso_ctrl_tech; |
| 1612 | } |
| 1613 | |
| 1614 | return ret; |
| 1615 | } |
| 1616 | |
| 1617 | /* Since this is a target routine, several of the framing calls are |
| 1618 | * made between receiving the request and sending the response so they |
| 1619 | * should take effect until after the response is sent. This is accomplished |
| 1620 | * by skipping the ISO_CTRL register write here and doing it in the interrupt |
| 1621 | * handler. |
| 1622 | */ |
| 1623 | static int trf7970a_tg_config_framing(struct trf7970a *trf, int framing) |
| 1624 | { |
| 1625 | u8 iso_ctrl = trf->iso_ctrl_tech; |
| 1626 | int ret; |
| 1627 | |
| 1628 | dev_dbg(trf->dev, "framing: %d\n", framing); |
| 1629 | |
| 1630 | switch (framing) { |
| 1631 | case NFC_DIGITAL_FRAMING_NFCA_NFC_DEP: |
| 1632 | trf->tx_cmd = TRF7970A_CMD_TRANSMIT_NO_CRC; |
| 1633 | iso_ctrl |= TRF7970A_ISO_CTRL_RX_CRC_N; |
| 1634 | break; |
| 1635 | case NFC_DIGITAL_FRAMING_NFCA_STANDARD: |
| 1636 | case NFC_DIGITAL_FRAMING_NFCA_STANDARD_WITH_CRC_A: |
| 1637 | case NFC_DIGITAL_FRAMING_NFCA_ANTICOL_COMPLETE: |
| 1638 | /* These ones are applied in the interrupt handler */ |
| 1639 | iso_ctrl = trf->iso_ctrl; /* Don't write to ISO_CTRL yet */ |
| 1640 | break; |
| 1641 | case NFC_DIGITAL_FRAMING_NFCF_NFC_DEP: |
| 1642 | trf->tx_cmd = TRF7970A_CMD_TRANSMIT; |
| 1643 | iso_ctrl &= ~TRF7970A_ISO_CTRL_RX_CRC_N; |
| 1644 | break; |
| 1645 | case NFC_DIGITAL_FRAMING_NFC_DEP_ACTIVATED: |
| 1646 | trf->tx_cmd = TRF7970A_CMD_TRANSMIT; |
| 1647 | iso_ctrl &= ~TRF7970A_ISO_CTRL_RX_CRC_N; |
| 1648 | break; |
| 1649 | default: |
| 1650 | dev_dbg(trf->dev, "Unsupported Framing: %d\n", framing); |
| 1651 | return -EINVAL; |
| 1652 | } |
| 1653 | |
| 1654 | trf->framing = framing; |
| 1655 | |
| 1656 | if (iso_ctrl != trf->iso_ctrl) { |
| 1657 | ret = trf7970a_write(trf, TRF7970A_ISO_CTRL, iso_ctrl); |
| 1658 | if (ret) |
| 1659 | return ret; |
| 1660 | |
| 1661 | trf->iso_ctrl = iso_ctrl; |
| 1662 | |
| 1663 | ret = trf7970a_write(trf, TRF7970A_MODULATOR_SYS_CLK_CTRL, |
| 1664 | trf->modulator_sys_clk_ctrl); |
| 1665 | if (ret) |
| 1666 | return ret; |
| 1667 | } |
| 1668 | |
| 1669 | if (!(trf->chip_status_ctrl & TRF7970A_CHIP_STATUS_RF_ON)) { |
| 1670 | ret = trf7970a_write(trf, TRF7970A_CHIP_STATUS_CTRL, |
| 1671 | trf->chip_status_ctrl | |
| 1672 | TRF7970A_CHIP_STATUS_RF_ON); |
| 1673 | if (ret) |
| 1674 | return ret; |
| 1675 | |
| 1676 | trf->chip_status_ctrl |= TRF7970A_CHIP_STATUS_RF_ON; |
| 1677 | } |
| 1678 | |
| 1679 | return 0; |
| 1680 | } |
| 1681 | |
| 1682 | static int trf7970a_tg_configure_hw(struct nfc_digital_dev *ddev, int type, |
| 1683 | int param) |
| 1684 | { |
| 1685 | struct trf7970a *trf = nfc_digital_get_drvdata(ddev); |
| 1686 | int ret; |
| 1687 | |
| 1688 | dev_dbg(trf->dev, "Configure hw - type: %d, param: %d\n", type, param); |
| 1689 | |
| 1690 | mutex_lock(&trf->lock); |
| 1691 | |
| 1692 | trf->is_initiator = false; |
| 1693 | |
| 1694 | if ((trf->state == TRF7970A_ST_PWR_OFF) || |
| 1695 | (trf->state == TRF7970A_ST_RF_OFF)) { |
| 1696 | ret = trf7970a_switch_rf_on(trf); |
| 1697 | if (ret) |
| 1698 | goto err_unlock; |
| 1699 | } |
| 1700 | |
| 1701 | switch (type) { |
| 1702 | case NFC_DIGITAL_CONFIG_RF_TECH: |
| 1703 | ret = trf7970a_tg_config_rf_tech(trf, param); |
| 1704 | break; |
| 1705 | case NFC_DIGITAL_CONFIG_FRAMING: |
| 1706 | ret = trf7970a_tg_config_framing(trf, param); |
| 1707 | break; |
| 1708 | default: |
| 1709 | dev_dbg(trf->dev, "Unknown type: %d\n", type); |
| 1710 | ret = -EINVAL; |
| 1711 | } |
| 1712 | |
| 1713 | err_unlock: |
| 1714 | mutex_unlock(&trf->lock); |
| 1715 | return ret; |
| 1716 | } |
| 1717 | |
| 1718 | static int _trf7970a_tg_listen(struct nfc_digital_dev *ddev, u16 timeout, |
| 1719 | nfc_digital_cmd_complete_t cb, void *arg, |
| 1720 | bool mode_detect) |
| 1721 | { |
| 1722 | struct trf7970a *trf = nfc_digital_get_drvdata(ddev); |
| 1723 | int ret; |
| 1724 | |
| 1725 | mutex_lock(&trf->lock); |
| 1726 | |
| 1727 | if ((trf->state != TRF7970A_ST_IDLE) && |
| 1728 | (trf->state != TRF7970A_ST_IDLE_RX_BLOCKED)) { |
| 1729 | dev_err(trf->dev, "%s - Bogus state: %d\n", __func__, |
| 1730 | trf->state); |
| 1731 | ret = -EIO; |
| 1732 | goto out_err; |
| 1733 | } |
| 1734 | |
| 1735 | if (trf->aborting) { |
| 1736 | dev_dbg(trf->dev, "Abort process complete\n"); |
| 1737 | trf->aborting = false; |
| 1738 | ret = -ECANCELED; |
| 1739 | goto out_err; |
| 1740 | } |
| 1741 | |
| 1742 | trf->rx_skb = nfc_alloc_recv_skb(TRF7970A_RX_SKB_ALLOC_SIZE, |
| 1743 | GFP_KERNEL); |
| 1744 | if (!trf->rx_skb) { |
| 1745 | dev_dbg(trf->dev, "Can't alloc rx_skb\n"); |
| 1746 | ret = -ENOMEM; |
| 1747 | goto out_err; |
| 1748 | } |
| 1749 | |
| 1750 | ret = trf7970a_write(trf, TRF7970A_RX_SPECIAL_SETTINGS, |
| 1751 | TRF7970A_RX_SPECIAL_SETTINGS_HBT | |
| 1752 | TRF7970A_RX_SPECIAL_SETTINGS_M848 | |
| 1753 | TRF7970A_RX_SPECIAL_SETTINGS_C424 | |
| 1754 | TRF7970A_RX_SPECIAL_SETTINGS_C212); |
| 1755 | if (ret) |
| 1756 | goto out_err; |
| 1757 | |
| 1758 | ret = trf7970a_write(trf, TRF7970A_REG_IO_CTRL, |
| 1759 | trf->io_ctrl | TRF7970A_REG_IO_CTRL_VRS(0x1)); |
| 1760 | if (ret) |
| 1761 | goto out_err; |
| 1762 | |
| 1763 | ret = trf7970a_write(trf, TRF7970A_NFC_LOW_FIELD_LEVEL, |
| 1764 | TRF7970A_NFC_LOW_FIELD_LEVEL_RFDET(0x3)); |
| 1765 | if (ret) |
| 1766 | goto out_err; |
| 1767 | |
| 1768 | ret = trf7970a_write(trf, TRF7970A_NFC_TARGET_LEVEL, |
| 1769 | TRF7970A_NFC_TARGET_LEVEL_RFDET(0x7)); |
| 1770 | if (ret) |
| 1771 | goto out_err; |
| 1772 | |
| 1773 | trf->ddev = ddev; |
| 1774 | trf->cb = cb; |
| 1775 | trf->cb_arg = arg; |
| 1776 | trf->timeout = timeout; |
| 1777 | trf->ignore_timeout = false; |
| 1778 | |
| 1779 | ret = trf7970a_cmd(trf, TRF7970A_CMD_ENABLE_RX); |
| 1780 | if (ret) |
| 1781 | goto out_err; |
| 1782 | |
| 1783 | trf->state = mode_detect ? TRF7970A_ST_LISTENING_MD : |
| 1784 | TRF7970A_ST_LISTENING; |
| 1785 | |
| 1786 | schedule_delayed_work(&trf->timeout_work, msecs_to_jiffies(timeout)); |
| 1787 | |
| 1788 | out_err: |
| 1789 | mutex_unlock(&trf->lock); |
| 1790 | return ret; |
| 1791 | } |
| 1792 | |
| 1793 | static int trf7970a_tg_listen(struct nfc_digital_dev *ddev, u16 timeout, |
| 1794 | nfc_digital_cmd_complete_t cb, void *arg) |
| 1795 | { |
| 1796 | const struct trf7970a *trf = nfc_digital_get_drvdata(ddev); |
| 1797 | |
| 1798 | dev_dbg(trf->dev, "Listen - state: %d, timeout: %d ms\n", |
| 1799 | trf->state, timeout); |
| 1800 | |
| 1801 | return _trf7970a_tg_listen(ddev, timeout, cb, arg, false); |
| 1802 | } |
| 1803 | |
| 1804 | static int trf7970a_tg_listen_md(struct nfc_digital_dev *ddev, |
| 1805 | u16 timeout, nfc_digital_cmd_complete_t cb, |
| 1806 | void *arg) |
| 1807 | { |
| 1808 | const struct trf7970a *trf = nfc_digital_get_drvdata(ddev); |
| 1809 | int ret; |
| 1810 | |
| 1811 | dev_dbg(trf->dev, "Listen MD - state: %d, timeout: %d ms\n", |
| 1812 | trf->state, timeout); |
| 1813 | |
| 1814 | ret = trf7970a_tg_configure_hw(ddev, NFC_DIGITAL_CONFIG_RF_TECH, |
| 1815 | NFC_DIGITAL_RF_TECH_106A); |
| 1816 | if (ret) |
| 1817 | return ret; |
| 1818 | |
| 1819 | ret = trf7970a_tg_configure_hw(ddev, NFC_DIGITAL_CONFIG_FRAMING, |
| 1820 | NFC_DIGITAL_FRAMING_NFCA_NFC_DEP); |
| 1821 | if (ret) |
| 1822 | return ret; |
| 1823 | |
| 1824 | return _trf7970a_tg_listen(ddev, timeout, cb, arg, true); |
| 1825 | } |
| 1826 | |
| 1827 | static int trf7970a_tg_get_rf_tech(struct nfc_digital_dev *ddev, u8 *rf_tech) |
| 1828 | { |
| 1829 | const struct trf7970a *trf = nfc_digital_get_drvdata(ddev); |
| 1830 | |
| 1831 | dev_dbg(trf->dev, "Get RF Tech - state: %d, rf_tech: %d\n", |
| 1832 | trf->state, trf->md_rf_tech); |
| 1833 | |
| 1834 | *rf_tech = trf->md_rf_tech; |
| 1835 | |
| 1836 | return 0; |
| 1837 | } |
| 1838 | |
| 1839 | static void trf7970a_abort_cmd(struct nfc_digital_dev *ddev) |
| 1840 | { |
| 1841 | struct trf7970a *trf = nfc_digital_get_drvdata(ddev); |
| 1842 | |
| 1843 | dev_dbg(trf->dev, "Abort process initiated\n"); |
| 1844 | |
| 1845 | mutex_lock(&trf->lock); |
| 1846 | |
| 1847 | switch (trf->state) { |
| 1848 | case TRF7970A_ST_WAIT_FOR_TX_FIFO: |
| 1849 | case TRF7970A_ST_WAIT_FOR_RX_DATA: |
| 1850 | case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT: |
| 1851 | case TRF7970A_ST_WAIT_TO_ISSUE_EOF: |
| 1852 | trf->aborting = true; |
| 1853 | break; |
| 1854 | case TRF7970A_ST_LISTENING: |
| 1855 | trf->ignore_timeout = !cancel_delayed_work(&trf->timeout_work); |
| 1856 | trf7970a_send_err_upstream(trf, -ECANCELED); |
| 1857 | dev_dbg(trf->dev, "Abort process complete\n"); |
| 1858 | break; |
| 1859 | default: |
| 1860 | break; |
| 1861 | } |
| 1862 | |
| 1863 | mutex_unlock(&trf->lock); |
| 1864 | } |
| 1865 | |
| 1866 | static const struct nfc_digital_ops trf7970a_nfc_ops = { |
| 1867 | .in_configure_hw = trf7970a_in_configure_hw, |
| 1868 | .in_send_cmd = trf7970a_send_cmd, |
| 1869 | .tg_configure_hw = trf7970a_tg_configure_hw, |
| 1870 | .tg_send_cmd = trf7970a_send_cmd, |
| 1871 | .tg_listen = trf7970a_tg_listen, |
| 1872 | .tg_listen_md = trf7970a_tg_listen_md, |
| 1873 | .tg_get_rf_tech = trf7970a_tg_get_rf_tech, |
| 1874 | .switch_rf = trf7970a_switch_rf, |
| 1875 | .abort_cmd = trf7970a_abort_cmd, |
| 1876 | }; |
| 1877 | |
| 1878 | static int trf7970a_power_up(struct trf7970a *trf) |
| 1879 | { |
| 1880 | int ret; |
| 1881 | |
| 1882 | dev_dbg(trf->dev, "Powering up - state: %d\n", trf->state); |
| 1883 | |
| 1884 | if (trf->state != TRF7970A_ST_PWR_OFF) |
| 1885 | return 0; |
| 1886 | |
| 1887 | ret = regulator_enable(trf->vin_regulator); |
| 1888 | if (ret) { |
| 1889 | dev_err(trf->dev, "%s - Can't enable VIN: %d\n", __func__, ret); |
| 1890 | return ret; |
| 1891 | } |
| 1892 | |
| 1893 | usleep_range(5000, 6000); |
| 1894 | |
| 1895 | if (trf->en2_gpiod && |
| 1896 | !(trf->quirks & TRF7970A_QUIRK_EN2_MUST_STAY_LOW)) { |
| 1897 | gpiod_set_value_cansleep(trf->en2_gpiod, 1); |
| 1898 | usleep_range(1000, 2000); |
| 1899 | } |
| 1900 | |
| 1901 | gpiod_set_value_cansleep(trf->en_gpiod, 1); |
| 1902 | |
| 1903 | usleep_range(20000, 21000); |
| 1904 | |
| 1905 | trf->state = TRF7970A_ST_RF_OFF; |
| 1906 | |
| 1907 | return 0; |
| 1908 | } |
| 1909 | |
| 1910 | static int trf7970a_power_down(struct trf7970a *trf) |
| 1911 | { |
| 1912 | int ret; |
| 1913 | |
| 1914 | dev_dbg(trf->dev, "Powering down - state: %d\n", trf->state); |
| 1915 | |
| 1916 | if (trf->state == TRF7970A_ST_PWR_OFF) |
| 1917 | return 0; |
| 1918 | |
| 1919 | if (trf->state != TRF7970A_ST_RF_OFF) { |
| 1920 | dev_dbg(trf->dev, "Can't power down - not RF_OFF state (%d)\n", |
| 1921 | trf->state); |
| 1922 | return -EBUSY; |
| 1923 | } |
| 1924 | |
| 1925 | gpiod_set_value_cansleep(trf->en_gpiod, 0); |
| 1926 | |
| 1927 | if (trf->en2_gpiod && !(trf->quirks & TRF7970A_QUIRK_EN2_MUST_STAY_LOW)) |
| 1928 | gpiod_set_value_cansleep(trf->en2_gpiod, 0); |
| 1929 | |
| 1930 | ret = regulator_disable(trf->vin_regulator); |
| 1931 | if (ret) |
| 1932 | dev_err(trf->dev, "%s - Can't disable VIN: %d\n", __func__, |
| 1933 | ret); |
| 1934 | |
| 1935 | trf->state = TRF7970A_ST_PWR_OFF; |
| 1936 | |
| 1937 | return ret; |
| 1938 | } |
| 1939 | |
| 1940 | static int trf7970a_startup(struct trf7970a *trf) |
| 1941 | { |
| 1942 | int ret; |
| 1943 | |
| 1944 | ret = trf7970a_power_up(trf); |
| 1945 | if (ret) |
| 1946 | return ret; |
| 1947 | |
| 1948 | pm_runtime_set_active(trf->dev); |
| 1949 | pm_runtime_enable(trf->dev); |
| 1950 | pm_runtime_mark_last_busy(trf->dev); |
| 1951 | |
| 1952 | return 0; |
| 1953 | } |
| 1954 | |
| 1955 | static void trf7970a_shutdown(struct trf7970a *trf) |
| 1956 | { |
| 1957 | switch (trf->state) { |
| 1958 | case TRF7970A_ST_WAIT_FOR_TX_FIFO: |
| 1959 | case TRF7970A_ST_WAIT_FOR_RX_DATA: |
| 1960 | case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT: |
| 1961 | case TRF7970A_ST_WAIT_TO_ISSUE_EOF: |
| 1962 | case TRF7970A_ST_LISTENING: |
| 1963 | trf7970a_send_err_upstream(trf, -ECANCELED); |
| 1964 | fallthrough; |
| 1965 | case TRF7970A_ST_IDLE: |
| 1966 | case TRF7970A_ST_IDLE_RX_BLOCKED: |
| 1967 | trf7970a_switch_rf_off(trf); |
| 1968 | break; |
| 1969 | default: |
| 1970 | break; |
| 1971 | } |
| 1972 | |
| 1973 | pm_runtime_disable(trf->dev); |
| 1974 | pm_runtime_set_suspended(trf->dev); |
| 1975 | |
| 1976 | trf7970a_power_down(trf); |
| 1977 | } |
| 1978 | |
| 1979 | static int trf7970a_get_autosuspend_delay(const struct device_node *np) |
| 1980 | { |
| 1981 | int autosuspend_delay, ret; |
| 1982 | |
| 1983 | ret = of_property_read_u32(np, "autosuspend-delay", &autosuspend_delay); |
| 1984 | if (ret) |
| 1985 | autosuspend_delay = TRF7970A_AUTOSUSPEND_DELAY; |
| 1986 | |
| 1987 | return autosuspend_delay; |
| 1988 | } |
| 1989 | |
| 1990 | static int trf7970a_probe(struct spi_device *spi) |
| 1991 | { |
| 1992 | const struct device_node *np = spi->dev.of_node; |
| 1993 | struct trf7970a *trf; |
| 1994 | int uvolts, autosuspend_delay, ret; |
| 1995 | u32 clk_freq = TRF7970A_13MHZ_CLOCK_FREQUENCY; |
| 1996 | |
| 1997 | if (!np) { |
| 1998 | dev_err(&spi->dev, "No Device Tree entry\n"); |
| 1999 | return -EINVAL; |
| 2000 | } |
| 2001 | |
| 2002 | trf = devm_kzalloc(&spi->dev, sizeof(*trf), GFP_KERNEL); |
| 2003 | if (!trf) |
| 2004 | return -ENOMEM; |
| 2005 | |
| 2006 | trf->state = TRF7970A_ST_PWR_OFF; |
| 2007 | trf->dev = &spi->dev; |
| 2008 | trf->spi = spi; |
| 2009 | |
| 2010 | spi->mode = SPI_MODE_1; |
| 2011 | spi->bits_per_word = 8; |
| 2012 | |
| 2013 | ret = spi_setup(spi); |
| 2014 | if (ret < 0) { |
| 2015 | dev_err(trf->dev, "Can't set up SPI Communication\n"); |
| 2016 | return ret; |
| 2017 | } |
| 2018 | |
| 2019 | if (of_property_read_bool(np, "irq-status-read-quirk")) |
| 2020 | trf->quirks |= TRF7970A_QUIRK_IRQ_STATUS_READ; |
| 2021 | |
| 2022 | /* There are two enable pins - only EN must be present in the DT */ |
| 2023 | trf->en_gpiod = devm_gpiod_get_index(trf->dev, "ti,enable", 0, |
| 2024 | GPIOD_OUT_LOW); |
| 2025 | if (IS_ERR(trf->en_gpiod)) { |
| 2026 | dev_err(trf->dev, "No EN GPIO property\n"); |
| 2027 | return PTR_ERR(trf->en_gpiod); |
| 2028 | } |
| 2029 | |
| 2030 | trf->en2_gpiod = devm_gpiod_get_index_optional(trf->dev, "ti,enable", 1, |
| 2031 | GPIOD_OUT_LOW); |
| 2032 | if (!trf->en2_gpiod) { |
| 2033 | dev_info(trf->dev, "No EN2 GPIO property\n"); |
| 2034 | } else if (IS_ERR(trf->en2_gpiod)) { |
| 2035 | dev_err(trf->dev, "Error getting EN2 GPIO property: %ld\n", |
| 2036 | PTR_ERR(trf->en2_gpiod)); |
| 2037 | return PTR_ERR(trf->en2_gpiod); |
| 2038 | } else if (of_property_read_bool(np, "en2-rf-quirk")) { |
| 2039 | trf->quirks |= TRF7970A_QUIRK_EN2_MUST_STAY_LOW; |
| 2040 | } |
| 2041 | |
| 2042 | of_property_read_u32(np, "clock-frequency", &clk_freq); |
| 2043 | if ((clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY) && |
| 2044 | (clk_freq != TRF7970A_13MHZ_CLOCK_FREQUENCY)) { |
| 2045 | dev_err(trf->dev, |
| 2046 | "clock-frequency (%u Hz) unsupported\n", clk_freq); |
| 2047 | return -EINVAL; |
| 2048 | } |
| 2049 | |
| 2050 | if (clk_freq == TRF7970A_27MHZ_CLOCK_FREQUENCY) { |
| 2051 | trf->modulator_sys_clk_ctrl = TRF7970A_MODULATOR_27MHZ; |
| 2052 | dev_dbg(trf->dev, "trf7970a configured for 27MHz crystal\n"); |
| 2053 | } else { |
| 2054 | trf->modulator_sys_clk_ctrl = 0; |
| 2055 | } |
| 2056 | |
| 2057 | ret = devm_request_threaded_irq(trf->dev, spi->irq, NULL, |
| 2058 | trf7970a_irq, |
| 2059 | IRQF_TRIGGER_RISING | IRQF_ONESHOT, |
| 2060 | "trf7970a", trf); |
| 2061 | if (ret) { |
| 2062 | dev_err(trf->dev, "Can't request IRQ#%d: %d\n", spi->irq, ret); |
| 2063 | return ret; |
| 2064 | } |
| 2065 | |
| 2066 | mutex_init(&trf->lock); |
| 2067 | INIT_DELAYED_WORK(&trf->timeout_work, trf7970a_timeout_work_handler); |
| 2068 | |
| 2069 | trf->vin_regulator = devm_regulator_get(&spi->dev, "vin"); |
| 2070 | if (IS_ERR(trf->vin_regulator)) { |
| 2071 | ret = PTR_ERR(trf->vin_regulator); |
| 2072 | dev_err(trf->dev, "Can't get VIN regulator: %d\n", ret); |
| 2073 | goto err_destroy_lock; |
| 2074 | } |
| 2075 | |
| 2076 | ret = regulator_enable(trf->vin_regulator); |
| 2077 | if (ret) { |
| 2078 | dev_err(trf->dev, "Can't enable VIN: %d\n", ret); |
| 2079 | goto err_destroy_lock; |
| 2080 | } |
| 2081 | |
| 2082 | uvolts = regulator_get_voltage(trf->vin_regulator); |
| 2083 | if (uvolts > 4000000) |
| 2084 | trf->chip_status_ctrl = TRF7970A_CHIP_STATUS_VRS5_3; |
| 2085 | |
| 2086 | trf->vddio_regulator = devm_regulator_get(&spi->dev, "vdd-io"); |
| 2087 | if (IS_ERR(trf->vddio_regulator)) { |
| 2088 | ret = PTR_ERR(trf->vddio_regulator); |
| 2089 | dev_err(trf->dev, "Can't get VDD_IO regulator: %d\n", ret); |
| 2090 | goto err_disable_vin_regulator; |
| 2091 | } |
| 2092 | |
| 2093 | ret = regulator_enable(trf->vddio_regulator); |
| 2094 | if (ret) { |
| 2095 | dev_err(trf->dev, "Can't enable VDD_IO: %d\n", ret); |
| 2096 | goto err_disable_vin_regulator; |
| 2097 | } |
| 2098 | |
| 2099 | if (regulator_get_voltage(trf->vddio_regulator) == 1800000) { |
| 2100 | trf->io_ctrl = TRF7970A_REG_IO_CTRL_IO_LOW; |
| 2101 | dev_dbg(trf->dev, "trf7970a config vdd_io to 1.8V\n"); |
| 2102 | } |
| 2103 | |
| 2104 | trf->ddev = nfc_digital_allocate_device(&trf7970a_nfc_ops, |
| 2105 | TRF7970A_SUPPORTED_PROTOCOLS, |
| 2106 | NFC_DIGITAL_DRV_CAPS_IN_CRC | |
| 2107 | NFC_DIGITAL_DRV_CAPS_TG_CRC, 0, |
| 2108 | 0); |
| 2109 | if (!trf->ddev) { |
| 2110 | dev_err(trf->dev, "Can't allocate NFC digital device\n"); |
| 2111 | ret = -ENOMEM; |
| 2112 | goto err_disable_vddio_regulator; |
| 2113 | } |
| 2114 | |
| 2115 | nfc_digital_set_parent_dev(trf->ddev, trf->dev); |
| 2116 | nfc_digital_set_drvdata(trf->ddev, trf); |
| 2117 | spi_set_drvdata(spi, trf); |
| 2118 | |
| 2119 | autosuspend_delay = trf7970a_get_autosuspend_delay(np); |
| 2120 | |
| 2121 | pm_runtime_set_autosuspend_delay(trf->dev, autosuspend_delay); |
| 2122 | pm_runtime_use_autosuspend(trf->dev); |
| 2123 | |
| 2124 | ret = trf7970a_startup(trf); |
| 2125 | if (ret) |
| 2126 | goto err_free_ddev; |
| 2127 | |
| 2128 | ret = nfc_digital_register_device(trf->ddev); |
| 2129 | if (ret) { |
| 2130 | dev_err(trf->dev, "Can't register NFC digital device: %d\n", |
| 2131 | ret); |
| 2132 | goto err_shutdown; |
| 2133 | } |
| 2134 | |
| 2135 | return 0; |
| 2136 | |
| 2137 | err_shutdown: |
| 2138 | trf7970a_shutdown(trf); |
| 2139 | err_free_ddev: |
| 2140 | nfc_digital_free_device(trf->ddev); |
| 2141 | err_disable_vddio_regulator: |
| 2142 | regulator_disable(trf->vddio_regulator); |
| 2143 | err_disable_vin_regulator: |
| 2144 | regulator_disable(trf->vin_regulator); |
| 2145 | err_destroy_lock: |
| 2146 | mutex_destroy(&trf->lock); |
| 2147 | return ret; |
| 2148 | } |
| 2149 | |
| 2150 | static void trf7970a_remove(struct spi_device *spi) |
| 2151 | { |
| 2152 | struct trf7970a *trf = spi_get_drvdata(spi); |
| 2153 | |
| 2154 | mutex_lock(&trf->lock); |
| 2155 | |
| 2156 | trf7970a_shutdown(trf); |
| 2157 | |
| 2158 | mutex_unlock(&trf->lock); |
| 2159 | |
| 2160 | nfc_digital_unregister_device(trf->ddev); |
| 2161 | nfc_digital_free_device(trf->ddev); |
| 2162 | |
| 2163 | regulator_disable(trf->vddio_regulator); |
| 2164 | regulator_disable(trf->vin_regulator); |
| 2165 | |
| 2166 | mutex_destroy(&trf->lock); |
| 2167 | } |
| 2168 | |
| 2169 | #ifdef CONFIG_PM_SLEEP |
| 2170 | static int trf7970a_suspend(struct device *dev) |
| 2171 | { |
| 2172 | struct spi_device *spi = to_spi_device(dev); |
| 2173 | struct trf7970a *trf = spi_get_drvdata(spi); |
| 2174 | |
| 2175 | mutex_lock(&trf->lock); |
| 2176 | |
| 2177 | trf7970a_shutdown(trf); |
| 2178 | |
| 2179 | mutex_unlock(&trf->lock); |
| 2180 | |
| 2181 | return 0; |
| 2182 | } |
| 2183 | |
| 2184 | static int trf7970a_resume(struct device *dev) |
| 2185 | { |
| 2186 | struct spi_device *spi = to_spi_device(dev); |
| 2187 | struct trf7970a *trf = spi_get_drvdata(spi); |
| 2188 | int ret; |
| 2189 | |
| 2190 | mutex_lock(&trf->lock); |
| 2191 | |
| 2192 | ret = trf7970a_startup(trf); |
| 2193 | |
| 2194 | mutex_unlock(&trf->lock); |
| 2195 | |
| 2196 | return ret; |
| 2197 | } |
| 2198 | #endif |
| 2199 | |
| 2200 | #ifdef CONFIG_PM |
| 2201 | static int trf7970a_pm_runtime_suspend(struct device *dev) |
| 2202 | { |
| 2203 | struct spi_device *spi = to_spi_device(dev); |
| 2204 | struct trf7970a *trf = spi_get_drvdata(spi); |
| 2205 | int ret; |
| 2206 | |
| 2207 | mutex_lock(&trf->lock); |
| 2208 | |
| 2209 | ret = trf7970a_power_down(trf); |
| 2210 | |
| 2211 | mutex_unlock(&trf->lock); |
| 2212 | |
| 2213 | return ret; |
| 2214 | } |
| 2215 | |
| 2216 | static int trf7970a_pm_runtime_resume(struct device *dev) |
| 2217 | { |
| 2218 | struct spi_device *spi = to_spi_device(dev); |
| 2219 | struct trf7970a *trf = spi_get_drvdata(spi); |
| 2220 | int ret; |
| 2221 | |
| 2222 | ret = trf7970a_power_up(trf); |
| 2223 | if (!ret) |
| 2224 | pm_runtime_mark_last_busy(dev); |
| 2225 | |
| 2226 | return ret; |
| 2227 | } |
| 2228 | #endif |
| 2229 | |
| 2230 | static const struct dev_pm_ops trf7970a_pm_ops = { |
| 2231 | SET_SYSTEM_SLEEP_PM_OPS(trf7970a_suspend, trf7970a_resume) |
| 2232 | SET_RUNTIME_PM_OPS(trf7970a_pm_runtime_suspend, |
| 2233 | trf7970a_pm_runtime_resume, NULL) |
| 2234 | }; |
| 2235 | |
| 2236 | static const struct of_device_id trf7970a_of_match[] __maybe_unused = { |
| 2237 | {.compatible = "ti,trf7970a",}, |
| 2238 | {}, |
| 2239 | }; |
| 2240 | |
| 2241 | MODULE_DEVICE_TABLE(of, trf7970a_of_match); |
| 2242 | |
| 2243 | static const struct spi_device_id trf7970a_id_table[] = { |
| 2244 | {"trf7970a", 0}, |
| 2245 | {} |
| 2246 | }; |
| 2247 | |
| 2248 | MODULE_DEVICE_TABLE(spi, trf7970a_id_table); |
| 2249 | |
| 2250 | static struct spi_driver trf7970a_spi_driver = { |
| 2251 | .probe = trf7970a_probe, |
| 2252 | .remove = trf7970a_remove, |
| 2253 | .id_table = trf7970a_id_table, |
| 2254 | .driver = { |
| 2255 | .name = "trf7970a", |
| 2256 | .of_match_table = of_match_ptr(trf7970a_of_match), |
| 2257 | .pm = &trf7970a_pm_ops, |
| 2258 | }, |
| 2259 | }; |
| 2260 | |
| 2261 | module_spi_driver(trf7970a_spi_driver); |
| 2262 | |
| 2263 | MODULE_AUTHOR("Mark A. Greer <mgreer@animalcreek.com>"); |
| 2264 | MODULE_LICENSE("GPL v2"); |
| 2265 | MODULE_DESCRIPTION("TI trf7970a RFID/NFC Transceiver Driver"); |