Commit | Line | Data |
---|---|---|
e2be04c7 | 1 | /* SPDX-License-Identifier: GPL-1.0+ WITH Linux-syscall-note */ |
607ca46e DH |
2 | /* |
3 | * include/linux/serial.h | |
4 | * | |
5 | * Copyright (C) 1992 by Theodore Ts'o. | |
6 | * | |
7 | * Redistribution of this file is permitted under the terms of the GNU | |
8 | * Public License (GPL) | |
9 | */ | |
10 | ||
11 | #ifndef _UAPI_LINUX_SERIAL_H | |
12 | #define _UAPI_LINUX_SERIAL_H | |
13 | ||
76ac8e29 | 14 | #include <linux/const.h> |
607ca46e DH |
15 | #include <linux/types.h> |
16 | ||
17 | #include <linux/tty_flags.h> | |
18 | ||
19 | ||
20 | struct serial_struct { | |
21 | int type; | |
22 | int line; | |
23 | unsigned int port; | |
24 | int irq; | |
25 | int flags; | |
26 | int xmit_fifo_size; | |
27 | int custom_divisor; | |
28 | int baud_base; | |
29 | unsigned short close_delay; | |
30 | char io_type; | |
31 | char reserved_char[1]; | |
32 | int hub6; | |
33 | unsigned short closing_wait; /* time to wait before closing */ | |
34 | unsigned short closing_wait2; /* no longer used... */ | |
35 | unsigned char *iomem_base; | |
36 | unsigned short iomem_reg_shift; | |
37 | unsigned int port_high; | |
38 | unsigned long iomap_base; /* cookie passed into ioremap */ | |
39 | }; | |
40 | ||
41 | /* | |
42 | * For the close wait times, 0 means wait forever for serial port to | |
43 | * flush its output. 65535 means don't wait at all. | |
44 | */ | |
45 | #define ASYNC_CLOSING_WAIT_INF 0 | |
46 | #define ASYNC_CLOSING_WAIT_NONE 65535 | |
47 | ||
48 | /* | |
49 | * These are the supported serial types. | |
50 | */ | |
51 | #define PORT_UNKNOWN 0 | |
52 | #define PORT_8250 1 | |
53 | #define PORT_16450 2 | |
54 | #define PORT_16550 3 | |
55 | #define PORT_16550A 4 | |
f76edd8f | 56 | #define PORT_CIRRUS 5 |
607ca46e DH |
57 | #define PORT_16650 6 |
58 | #define PORT_16650V2 7 | |
59 | #define PORT_16750 8 | |
f76edd8f | 60 | #define PORT_STARTECH 9 |
607ca46e DH |
61 | #define PORT_16C950 10 /* Oxford Semiconductor */ |
62 | #define PORT_16654 11 | |
63 | #define PORT_16850 12 | |
64 | #define PORT_RSA 13 /* RSA-DV II/S card */ | |
65 | #define PORT_MAX 13 | |
66 | ||
67 | #define SERIAL_IO_PORT 0 | |
68 | #define SERIAL_IO_HUB6 1 | |
69 | #define SERIAL_IO_MEM 2 | |
647f162b PH |
70 | #define SERIAL_IO_MEM32 3 |
71 | #define SERIAL_IO_AU 4 | |
72 | #define SERIAL_IO_TSI 5 | |
73 | #define SERIAL_IO_MEM32BE 6 | |
bd94c407 | 74 | #define SERIAL_IO_MEM16 7 |
607ca46e DH |
75 | |
76 | #define UART_CLEAR_FIFO 0x01 | |
77 | #define UART_USE_FIFO 0x02 | |
78 | #define UART_STARTECH 0x04 | |
79 | #define UART_NATSEMI 0x08 | |
80 | ||
81 | ||
82 | /* | |
83 | * Multiport serial configuration structure --- external structure | |
84 | */ | |
85 | struct serial_multiport_struct { | |
86 | int irq; | |
87 | int port1; | |
88 | unsigned char mask1, match1; | |
89 | int port2; | |
90 | unsigned char mask2, match2; | |
91 | int port3; | |
92 | unsigned char mask3, match3; | |
93 | int port4; | |
94 | unsigned char mask4, match4; | |
95 | int port_monitor; | |
96 | int reserved[32]; | |
97 | }; | |
98 | ||
99 | /* | |
100 | * Serial input interrupt line counters -- external structure | |
101 | * Four lines can interrupt: CTS, DSR, RI, DCD | |
102 | */ | |
103 | struct serial_icounter_struct { | |
104 | int cts, dsr, rng, dcd; | |
105 | int rx, tx; | |
106 | int frame, overrun, parity, brk; | |
107 | int buf_overrun; | |
108 | int reserved[9]; | |
109 | }; | |
110 | ||
6dd07781 IJ |
111 | /** |
112 | * struct serial_rs485 - serial interface for controlling RS485 settings. | |
113 | * @flags: RS485 feature flags. | |
114 | * @delay_rts_before_send: Delay before send (milliseconds). | |
115 | * @delay_rts_after_send: Delay after send (milliseconds). | |
116 | * @addr_recv: Receive filter for RS485 addressing mode | |
117 | * (used only when %SER_RS485_ADDR_RECV is set). | |
118 | * @addr_dest: Destination address for RS485 addressing mode | |
119 | * (used only when %SER_RS485_ADDR_DEST is set). | |
120 | * @padding0: Padding (set to zero). | |
121 | * @padding1: Padding (set to zero). | |
122 | * @padding: Deprecated, use @padding0 and @padding1 instead. | |
123 | * Do not use with @addr_recv and @addr_dest (due to | |
124 | * overlap). | |
125 | * | |
607ca46e DH |
126 | * Serial interface for controlling RS485 settings on chips with suitable |
127 | * support. Set with TIOCSRS485 and get with TIOCGRS485 if supported by your | |
128 | * platform. The set function returns the new state, with any unsupported bits | |
129 | * reverted appropriately. | |
6dd07781 IJ |
130 | * |
131 | * The flag bits are: | |
132 | * | |
133 | * * %SER_RS485_ENABLED - RS485 enabled. | |
134 | * * %SER_RS485_RTS_ON_SEND - Logical level for RTS pin when sending. | |
135 | * * %SER_RS485_RTS_AFTER_SEND - Logical level for RTS pin after sent. | |
136 | * * %SER_RS485_RX_DURING_TX - Full-duplex RS485 line. | |
137 | * * %SER_RS485_TERMINATE_BUS - Enable bus termination (if supported). | |
138 | * * %SER_RS485_ADDRB - Enable RS485 addressing mode. | |
139 | * * %SER_RS485_ADDR_RECV - Receive address filter (enables @addr_recv). Requires %SER_RS485_ADDRB. | |
140 | * * %SER_RS485_ADDR_DEST - Destination address (enables @addr_dest). Requires %SER_RS485_ADDRB. | |
6056f20f | 141 | * * %SER_RS485_MODE_RS422 - Enable RS422. Requires %SER_RS485_ENABLED. |
607ca46e | 142 | */ |
607ca46e | 143 | struct serial_rs485 { |
6dd07781 | 144 | __u32 flags; |
76ac8e29 CCH |
145 | #define SER_RS485_ENABLED _BITUL(0) |
146 | #define SER_RS485_RTS_ON_SEND _BITUL(1) | |
147 | #define SER_RS485_RTS_AFTER_SEND _BITUL(2) | |
e15c99be CN |
148 | /* Placeholder for bit 3: SER_RS485_RTS_BEFORE_SEND, which isn't used anymore */ |
149 | #define SER_RS485_RX_DURING_TX _BITUL(4) | |
150 | #define SER_RS485_TERMINATE_BUS _BITUL(5) | |
151 | #define SER_RS485_ADDRB _BITUL(6) | |
152 | #define SER_RS485_ADDR_RECV _BITUL(7) | |
153 | #define SER_RS485_ADDR_DEST _BITUL(8) | |
154 | #define SER_RS485_MODE_RS422 _BITUL(9) | |
4f768e94 | 155 | |
6dd07781 IJ |
156 | __u32 delay_rts_before_send; |
157 | __u32 delay_rts_after_send; | |
4f768e94 IJ |
158 | |
159 | /* The fields below are defined by flags */ | |
160 | union { | |
161 | __u32 padding[5]; /* Memory is cheap, new structs are a pain */ | |
162 | ||
163 | struct { | |
164 | __u8 addr_recv; | |
165 | __u8 addr_dest; | |
166 | __u8 padding0[2]; | |
167 | __u32 padding1[4]; | |
168 | }; | |
169 | }; | |
607ca46e DH |
170 | }; |
171 | ||
ad8c0eaa NF |
172 | /* |
173 | * Serial interface for controlling ISO7816 settings on chips with suitable | |
174 | * support. Set with TIOCSISO7816 and get with TIOCGISO7816 if supported by | |
175 | * your platform. | |
176 | */ | |
177 | struct serial_iso7816 { | |
178 | __u32 flags; /* ISO7816 feature flags */ | |
179 | #define SER_ISO7816_ENABLED (1 << 0) | |
180 | #define SER_ISO7816_T_PARAM (0x0f << 4) | |
181 | #define SER_ISO7816_T(t) (((t) & 0x0f) << 4) | |
182 | __u32 tg; | |
183 | __u32 sc_fi; | |
184 | __u32 sc_di; | |
185 | __u32 clk; | |
186 | __u32 reserved[5]; | |
187 | }; | |
188 | ||
607ca46e | 189 | #endif /* _UAPI_LINUX_SERIAL_H */ |