projects / linux-2.6-block.git / blame
| Commit | Line | Data |
|---|---|---|
| 1da177e4 LT |
1 | |
| 2 | /* include/asm-m68knommu/MC68VZ328.h: 'VZ328 control registers | |
| 3 | * | |
| 4 | * Copyright (c) 2000-2001 Lineo Inc. <www.lineo.com> | |
| 5 | * Copyright (c) 2000-2001 Lineo Canada Corp. <www.lineo.ca> | |
| 6 | * Copyright (C) 1999 Vladimir Gurevich <vgurevic@cisco.com> | |
| 7 | * Bare & Hare Software, Inc. | |
| 8 | * Based on include/asm-m68knommu/MC68332.h | |
| 9 | * Copyright (C) 1998 Kenneth Albanowski <kjahds@kjahds.com>, | |
| 10 | * The Silver Hammer Group, Ltd. | |
| 11 | * | |
| 12 | * M68VZ328 fixes by Evan Stawnyczy <evan@lineo.com> | |
| 13 | * vz multiport fixes by Michael Leslie <mleslie@lineo.com> | |
| 14 | */ | |
| 15 | ||
| 16 | #ifndef _MC68VZ328_H_ | |
| 17 | #define _MC68VZ328_H_ | |
| 18 | ||
| 19 | #define BYTE_REF(addr) (*((volatile unsigned char*)addr)) | |
| 20 | #define WORD_REF(addr) (*((volatile unsigned short*)addr)) | |
| 21 | #define LONG_REF(addr) (*((volatile unsigned long*)addr)) | |
| 22 | ||
| 23 | #define PUT_FIELD(field, val) (((val) << field##_SHIFT) & field##_MASK) | |
| 24 | #define GET_FIELD(reg, field) (((reg) & field##_MASK) >> field##_SHIFT) | |
| 25 | ||
| 26 | /********** | |
| 27 | * | |
| 28 | * 0xFFFFF0xx -- System Control | |
| 29 | * | |
| 30 | **********/ | |
| 31 | ||
| 32 | /* | |
| 33 | * System Control Register (SCR) | |
| 34 | */ | |
| 35 | #define SCR_ADDR 0xfffff000 | |
| 36 | #define SCR BYTE_REF(SCR_ADDR) | |
| 37 | ||
| 38 | #define SCR_WDTH8 0x01 /* 8-Bit Width Select */ | |
| 39 | #define SCR_DMAP 0x04 /* Double Map */ | |
| 40 | #define SCR_SO 0x08 /* Supervisor Only */ | |
| 41 | #define SCR_BETEN 0x10 /* Bus-Error Time-Out Enable */ | |
| 42 | #define SCR_PRV 0x20 /* Privilege Violation */ | |
| 43 | #define SCR_WPV 0x40 /* Write Protect Violation */ | |
| 44 | #define SCR_BETO 0x80 /* Bus-Error TimeOut */ | |
| 45 | ||
| 46 | /* | |
| 47 | * Silicon ID Register (Mask Revision Register (MRR) for '328 Compatibility) | |
| 48 | */ | |
| 49 | #define MRR_ADDR 0xfffff004 | |
| 50 | #define MRR LONG_REF(MRR_ADDR) | |
| 51 | ||
| 52 | /********** | |
| 53 | * | |
| 54 | * 0xFFFFF1xx -- Chip-Select logic | |
| 55 | * | |
| 56 | **********/ | |
| 57 | ||
| 58 | /* | |
| 59 | * Chip Select Group Base Registers | |
| 60 | */ | |
| 61 | #define CSGBA_ADDR 0xfffff100 | |
| 62 | #define CSGBB_ADDR 0xfffff102 | |
| 63 | ||
| 64 | #define CSGBC_ADDR 0xfffff104 | |
| 65 | #define CSGBD_ADDR 0xfffff106 | |
| 66 | ||
| 67 | #define CSGBA WORD_REF(CSGBA_ADDR) | |
| 68 | #define CSGBB WORD_REF(CSGBB_ADDR) | |
| 69 | #define CSGBC WORD_REF(CSGBC_ADDR) | |
| 70 | #define CSGBD WORD_REF(CSGBD_ADDR) | |
| 71 | ||
| 72 | /* | |
| 73 | * Chip Select Registers | |
| 74 | */ | |
| 75 | #define CSA_ADDR 0xfffff110 | |
| 76 | #define CSB_ADDR 0xfffff112 | |
| 77 | #define CSC_ADDR 0xfffff114 | |
| 78 | #define CSD_ADDR 0xfffff116 | |
| 79 | ||
| 80 | #define CSA WORD_REF(CSA_ADDR) | |
| 81 | #define CSB WORD_REF(CSB_ADDR) | |
| 82 | #define CSC WORD_REF(CSC_ADDR) | |
| 83 | #define CSD WORD_REF(CSD_ADDR) | |
| 84 | ||
| 85 | #define CSA_EN 0x0001 /* Chip-Select Enable */ | |
| 86 | #define CSA_SIZ_MASK 0x000e /* Chip-Select Size */ | |
| 87 | #define CSA_SIZ_SHIFT 1 | |
| 88 | #define CSA_WS_MASK 0x0070 /* Wait State */ | |
| 89 | #define CSA_WS_SHIFT 4 | |
| 90 | #define CSA_BSW 0x0080 /* Data Bus Width */ | |
| 91 | #define CSA_FLASH 0x0100 /* FLASH Memory Support */ | |
| 92 | #define CSA_RO 0x8000 /* Read-Only */ | |
| 93 | ||
| 94 | #define CSB_EN 0x0001 /* Chip-Select Enable */ | |
| 95 | #define CSB_SIZ_MASK 0x000e /* Chip-Select Size */ | |
| 96 | #define CSB_SIZ_SHIFT 1 | |
| 97 | #define CSB_WS_MASK 0x0070 /* Wait State */ | |
| 98 | #define CSB_WS_SHIFT 4 | |
| 99 | #define CSB_BSW 0x0080 /* Data Bus Width */ | |
| 100 | #define CSB_FLASH 0x0100 /* FLASH Memory Support */ | |
| 101 | #define CSB_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ | |
| 102 | #define CSB_UPSIZ_SHIFT 11 | |
| 103 | #define CSB_ROP 0x2000 /* Readonly if protected */ | |
| 104 | #define CSB_SOP 0x4000 /* Supervisor only if protected */ | |
| 105 | #define CSB_RO 0x8000 /* Read-Only */ | |
| 106 | ||
| 107 | #define CSC_EN 0x0001 /* Chip-Select Enable */ | |
| 108 | #define CSC_SIZ_MASK 0x000e /* Chip-Select Size */ | |
| 109 | #define CSC_SIZ_SHIFT 1 | |
| 110 | #define CSC_WS_MASK 0x0070 /* Wait State */ | |
| 111 | #define CSC_WS_SHIFT 4 | |
| 112 | #define CSC_BSW 0x0080 /* Data Bus Width */ | |
| 113 | #define CSC_FLASH 0x0100 /* FLASH Memory Support */ | |
| 114 | #define CSC_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ | |
| 115 | #define CSC_UPSIZ_SHIFT 11 | |
| 116 | #define CSC_ROP 0x2000 /* Readonly if protected */ | |
| 117 | #define CSC_SOP 0x4000 /* Supervisor only if protected */ | |
| 118 | #define CSC_RO 0x8000 /* Read-Only */ | |
| 119 | ||
| 120 | #define CSD_EN 0x0001 /* Chip-Select Enable */ | |
| 121 | #define CSD_SIZ_MASK 0x000e /* Chip-Select Size */ | |
| 122 | #define CSD_SIZ_SHIFT 1 | |
| 123 | #define CSD_WS_MASK 0x0070 /* Wait State */ | |
| 124 | #define CSD_WS_SHIFT 4 | |
| 125 | #define CSD_BSW 0x0080 /* Data Bus Width */ | |
| 126 | #define CSD_FLASH 0x0100 /* FLASH Memory Support */ | |
| 127 | #define CSD_DRAM 0x0200 /* Dram Selection */ | |
| 128 | #define CSD_COMB 0x0400 /* Combining */ | |
| 129 | #define CSD_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ | |
| 130 | #define CSD_UPSIZ_SHIFT 11 | |
| 131 | #define CSD_ROP 0x2000 /* Readonly if protected */ | |
| 132 | #define CSD_SOP 0x4000 /* Supervisor only if protected */ | |
| 133 | #define CSD_RO 0x8000 /* Read-Only */ | |
| 134 | ||
| 135 | /* | |
| 136 | * Emulation Chip-Select Register | |
| 137 | */ | |
| 138 | #define EMUCS_ADDR 0xfffff118 | |
| 139 | #define EMUCS WORD_REF(EMUCS_ADDR) | |
| 140 | ||
| 141 | #define EMUCS_WS_MASK 0x0070 | |
| 142 | #define EMUCS_WS_SHIFT 4 | |
| 143 | ||
| 144 | /********** | |
| 145 | * | |
| 146 | * 0xFFFFF2xx -- Phase Locked Loop (PLL) & Power Control | |
| 147 | * | |
| 148 | **********/ | |
| 149 | ||
| 150 | /* | |
| 151 | * PLL Control Register | |
| 152 | */ | |
| 153 | #define PLLCR_ADDR 0xfffff200 | |
| 154 | #define PLLCR WORD_REF(PLLCR_ADDR) | |
| 155 | ||
| 156 | #define PLLCR_DISPLL 0x0008 /* Disable PLL */ | |
| 157 | #define PLLCR_CLKEN 0x0010 /* Clock (CLKO pin) enable */ | |
| 158 | #define PLLCR_PRESC 0x0020 /* VCO prescaler */ | |
| 159 | #define PLLCR_SYSCLK_SEL_MASK 0x0700 /* System Clock Selection */ | |
| 160 | #define PLLCR_SYSCLK_SEL_SHIFT 8 | |
| 161 | #define PLLCR_LCDCLK_SEL_MASK 0x3800 /* LCD Clock Selection */ | |
| 162 | #define PLLCR_LCDCLK_SEL_SHIFT 11 | |
| 163 | ||
| 164 | /* '328-compatible definitions */ | |
| 165 | #define PLLCR_PIXCLK_SEL_MASK PLLCR_LCDCLK_SEL_MASK | |
| 166 | #define PLLCR_PIXCLK_SEL_SHIFT PLLCR_LCDCLK_SEL_SHIFT | |
| 167 | ||
| 168 | /* | |
| 169 | * PLL Frequency Select Register | |
| 170 | */ | |
| 171 | #define PLLFSR_ADDR 0xfffff202 | |
| 172 | #define PLLFSR WORD_REF(PLLFSR_ADDR) | |
| 173 | ||
| 174 | #define PLLFSR_PC_MASK 0x00ff /* P Count */ | |
| 175 | #define PLLFSR_PC_SHIFT 0 | |
| 176 | #define PLLFSR_QC_MASK 0x0f00 /* Q Count */ | |
| 177 | #define PLLFSR_QC_SHIFT 8 | |
| 178 | #define PLLFSR_PROT 0x4000 /* Protect P & Q */ | |
| 179 | #define PLLFSR_CLK32 0x8000 /* Clock 32 (kHz) */ | |
| 180 | ||
| 181 | /* | |
| 182 | * Power Control Register | |
| 183 | */ | |
| 184 | #define PCTRL_ADDR 0xfffff207 | |
| 185 | #define PCTRL BYTE_REF(PCTRL_ADDR) | |
| 186 | ||
| 187 | #define PCTRL_WIDTH_MASK 0x1f /* CPU Clock bursts width */ | |
| 188 | #define PCTRL_WIDTH_SHIFT 0 | |
| 189 | #define PCTRL_PCEN 0x80 /* Power Control Enable */ | |
| 190 | ||
| 191 | /********** | |
| 192 | * | |
| 193 | * 0xFFFFF3xx -- Interrupt Controller | |
| 194 | * | |
| 195 | **********/ | |
| 196 | ||
| 197 | /* | |
| 198 | * Interrupt Vector Register | |
| 199 | */ | |
| 200 | #define IVR_ADDR 0xfffff300 | |
| 201 | #define IVR BYTE_REF(IVR_ADDR) | |
| 202 | ||
| 203 | #define IVR_VECTOR_MASK 0xF8 | |
| 204 | ||
| 205 | /* | |
| 206 | * Interrupt control Register | |
| 207 | */ | |
| 208 | #define ICR_ADDR 0xfffff302 | |
| 209 | #define ICR WORD_REF(ICR_ADDR) | |
| 210 | ||
| 211 | #define ICR_POL5 0x0080 /* Polarity Control for IRQ5 */ | |
| 212 | #define ICR_ET6 0x0100 /* Edge Trigger Select for IRQ6 */ | |
| 213 | #define ICR_ET3 0x0200 /* Edge Trigger Select for IRQ3 */ | |
| 214 | #define ICR_ET2 0x0400 /* Edge Trigger Select for IRQ2 */ | |
| 215 | #define ICR_ET1 0x0800 /* Edge Trigger Select for IRQ1 */ | |
| 216 | #define ICR_POL6 0x1000 /* Polarity Control for IRQ6 */ | |
| 217 | #define ICR_POL3 0x2000 /* Polarity Control for IRQ3 */ | |
| 218 | #define ICR_POL2 0x4000 /* Polarity Control for IRQ2 */ | |
| 219 | #define ICR_POL1 0x8000 /* Polarity Control for IRQ1 */ | |
| 220 | ||
| 221 | /* | |
| 222 | * Interrupt Mask Register | |
| 223 | */ | |
| 224 | #define IMR_ADDR 0xfffff304 | |
| 225 | #define IMR LONG_REF(IMR_ADDR) | |
| 226 | ||
| 227 | /* | |
| 228 | * Define the names for bit positions first. This is useful for | |
| 229 | * request_irq | |
| 230 | */ | |
| 231 | #define SPI2_IRQ_NUM 0 /* SPI 2 interrupt */ | |
| 232 | #define TMR_IRQ_NUM 1 /* Timer 1 interrupt */ | |
| 233 | #define UART1_IRQ_NUM 2 /* UART 1 interrupt */ | |
| 234 | #define WDT_IRQ_NUM 3 /* Watchdog Timer interrupt */ | |
| 235 | #define RTC_IRQ_NUM 4 /* RTC interrupt */ | |
| 236 | #define TMR2_IRQ_NUM 5 /* Timer 2 interrupt */ | |
| 237 | #define KB_IRQ_NUM 6 /* Keyboard Interrupt */ | |
| 238 | #define PWM1_IRQ_NUM 7 /* Pulse-Width Modulator 1 int. */ | |
| 239 | #define INT0_IRQ_NUM 8 /* External INT0 */ | |
| 240 | #define INT1_IRQ_NUM 9 /* External INT1 */ | |
| 241 | #define INT2_IRQ_NUM 10 /* External INT2 */ | |
| 242 | #define INT3_IRQ_NUM 11 /* External INT3 */ | |
| 243 | #define UART2_IRQ_NUM 12 /* UART 2 interrupt */ | |
| 244 | #define PWM2_IRQ_NUM 13 /* Pulse-Width Modulator 1 int. */ | |
| 245 | #define IRQ1_IRQ_NUM 16 /* IRQ1 */ | |
| 246 | #define IRQ2_IRQ_NUM 17 /* IRQ2 */ | |
| 247 | #define IRQ3_IRQ_NUM 18 /* IRQ3 */ | |
| 248 | #define IRQ6_IRQ_NUM 19 /* IRQ6 */ | |
| 249 | #define IRQ5_IRQ_NUM 20 /* IRQ5 */ | |
| 250 | #define SPI1_IRQ_NUM 21 /* SPI 1 interrupt */ | |
| 251 | #define SAM_IRQ_NUM 22 /* Sampling Timer for RTC */ | |
| 252 | #define EMIQ_IRQ_NUM 23 /* Emulator Interrupt */ | |
| 253 | ||
| 254 | #define SPI_IRQ_NUM SPI2_IRQ_NUM | |
| 255 | ||
| 256 | /* '328-compatible definitions */ | |
| 257 | #define SPIM_IRQ_NUM SPI_IRQ_NUM | |
| 258 | #define TMR1_IRQ_NUM TMR_IRQ_NUM | |
| 259 | #define UART_IRQ_NUM UART1_IRQ_NUM | |
| 260 | ||
| 261 | /* | |
| 262 | * Here go the bitmasks themselves | |
| 263 | */ | |
| 264 | #define IMR_MSPI (1 << SPI_IRQ_NUM) /* Mask SPI interrupt */ | |
| 265 | #define IMR_MTMR (1 << TMR_IRQ_NUM) /* Mask Timer interrupt */ | |
| 266 | #define IMR_MUART (1 << UART_IRQ_NUM) /* Mask UART interrupt */ | |
| 267 | #define IMR_MWDT (1 << WDT_IRQ_NUM) /* Mask Watchdog Timer interrupt */ | |
| 268 | #define IMR_MRTC (1 << RTC_IRQ_NUM) /* Mask RTC interrupt */ | |
| 269 | #define IMR_MKB (1 << KB_IRQ_NUM) /* Mask Keyboard Interrupt */ | |
| 270 | #define IMR_MPWM (1 << PWM_IRQ_NUM) /* Mask Pulse-Width Modulator int. */ | |
| 271 | #define IMR_MINT0 (1 << INT0_IRQ_NUM) /* Mask External INT0 */ | |
| 272 | #define IMR_MINT1 (1 << INT1_IRQ_NUM) /* Mask External INT1 */ | |
| 273 | #define IMR_MINT2 (1 << INT2_IRQ_NUM) /* Mask External INT2 */ | |
| 274 | #define IMR_MINT3 (1 << INT3_IRQ_NUM) /* Mask External INT3 */ | |
| 275 | #define IMR_MIRQ1 (1 << IRQ1_IRQ_NUM) /* Mask IRQ1 */ | |
| 276 | #define IMR_MIRQ2 (1 << IRQ2_IRQ_NUM) /* Mask IRQ2 */ | |
| 277 | #define IMR_MIRQ3 (1 << IRQ3_IRQ_NUM) /* Mask IRQ3 */ | |
| 278 | #define IMR_MIRQ6 (1 << IRQ6_IRQ_NUM) /* Mask IRQ6 */ | |
| 279 | #define IMR_MIRQ5 (1 << IRQ5_IRQ_NUM) /* Mask IRQ5 */ | |
| 280 | #define IMR_MSAM (1 << SAM_IRQ_NUM) /* Mask Sampling Timer for RTC */ | |
| 281 | #define IMR_MEMIQ (1 << EMIQ_IRQ_NUM) /* Mask Emulator Interrupt */ | |
| 282 | ||
| 283 | /* '328-compatible definitions */ | |
| 284 | #define IMR_MSPIM IMR_MSPI | |
| 285 | #define IMR_MTMR1 IMR_MTMR | |
| 286 | ||
| 287 | /* | |
| 288 | * Interrupt Status Register | |
| 289 | */ | |
| 290 | #define ISR_ADDR 0xfffff30c | |
| 291 | #define ISR LONG_REF(ISR_ADDR) | |
| 292 | ||
| 293 | #define ISR_SPI (1 << SPI_IRQ_NUM) /* SPI interrupt */ | |
| 294 | #define ISR_TMR (1 << TMR_IRQ_NUM) /* Timer interrupt */ | |
| 295 | #define ISR_UART (1 << UART_IRQ_NUM) /* UART interrupt */ | |
| 296 | #define ISR_WDT (1 << WDT_IRQ_NUM) /* Watchdog Timer interrupt */ | |
| 297 | #define ISR_RTC (1 << RTC_IRQ_NUM) /* RTC interrupt */ | |
| 298 | #define ISR_KB (1 << KB_IRQ_NUM) /* Keyboard Interrupt */ | |
| 299 | #define ISR_PWM (1 << PWM_IRQ_NUM) /* Pulse-Width Modulator interrupt */ | |
| 300 | #define ISR_INT0 (1 << INT0_IRQ_NUM) /* External INT0 */ | |
| 301 | #define ISR_INT1 (1 << INT1_IRQ_NUM) /* External INT1 */ | |
| 302 | #define ISR_INT2 (1 << INT2_IRQ_NUM) /* External INT2 */ | |
| 303 | #define ISR_INT3 (1 << INT3_IRQ_NUM) /* External INT3 */ | |
| 304 | #define ISR_IRQ1 (1 << IRQ1_IRQ_NUM) /* IRQ1 */ | |
| 305 | #define ISR_IRQ2 (1 << IRQ2_IRQ_NUM) /* IRQ2 */ | |
| 306 | #define ISR_IRQ3 (1 << IRQ3_IRQ_NUM) /* IRQ3 */ | |
| 307 | #define ISR_IRQ6 (1 << IRQ6_IRQ_NUM) /* IRQ6 */ | |
| 308 | #define ISR_IRQ5 (1 << IRQ5_IRQ_NUM) /* IRQ5 */ | |
| 309 | #define ISR_SAM (1 << SAM_IRQ_NUM) /* Sampling Timer for RTC */ | |
| 310 | #define ISR_EMIQ (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */ | |
| 311 | ||
| 312 | /* '328-compatible definitions */ | |
| 313 | #define ISR_SPIM ISR_SPI | |
| 314 | #define ISR_TMR1 ISR_TMR | |
| 315 | ||
| 316 | /* | |
| 317 | * Interrupt Pending Register | |
| 318 | */ | |
| 319 | #define IPR_ADDR 0xfffff30c | |
| 320 | #define IPR LONG_REF(IPR_ADDR) | |
| 321 | ||
| 322 | #define IPR_SPI (1 << SPI_IRQ_NUM) /* SPI interrupt */ | |
| 323 | #define IPR_TMR (1 << TMR_IRQ_NUM) /* Timer interrupt */ | |
| 324 | #define IPR_UART (1 << UART_IRQ_NUM) /* UART interrupt */ | |
| 325 | #define IPR_WDT (1 << WDT_IRQ_NUM) /* Watchdog Timer interrupt */ | |
| 326 | #define IPR_RTC (1 << RTC_IRQ_NUM) /* RTC interrupt */ | |
| 327 | #define IPR_KB (1 << KB_IRQ_NUM) /* Keyboard Interrupt */ | |
| 328 | #define IPR_PWM (1 << PWM_IRQ_NUM) /* Pulse-Width Modulator interrupt */ | |
| 329 | #define IPR_INT0 (1 << INT0_IRQ_NUM) /* External INT0 */ | |
| 330 | #define IPR_INT1 (1 << INT1_IRQ_NUM) /* External INT1 */ | |
| 331 | #define IPR_INT2 (1 << INT2_IRQ_NUM) /* External INT2 */ | |
| 332 | #define IPR_INT3 (1 << INT3_IRQ_NUM) /* External INT3 */ | |
| 333 | #define IPR_IRQ1 (1 << IRQ1_IRQ_NUM) /* IRQ1 */ | |
| 334 | #define IPR_IRQ2 (1 << IRQ2_IRQ_NUM) /* IRQ2 */ | |
| 335 | #define IPR_IRQ3 (1 << IRQ3_IRQ_NUM) /* IRQ3 */ | |
| 336 | #define IPR_IRQ6 (1 << IRQ6_IRQ_NUM) /* IRQ6 */ | |
| 337 | #define IPR_IRQ5 (1 << IRQ5_IRQ_NUM) /* IRQ5 */ | |
| 338 | #define IPR_SAM (1 << SAM_IRQ_NUM) /* Sampling Timer for RTC */ | |
| 339 | #define IPR_EMIQ (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */ | |
| 340 | ||
| 341 | /* '328-compatible definitions */ | |
| 342 | #define IPR_SPIM IPR_SPI | |
| 343 | #define IPR_TMR1 IPR_TMR | |
| 344 | ||
| 345 | /********** | |
| 346 | * | |
| 347 | * 0xFFFFF4xx -- Parallel Ports | |
| 348 | * | |
| 349 | **********/ | |
| 350 | ||
| 351 | /* | |
| 352 | * Port A | |
| 353 | */ | |
| 354 | #define PADIR_ADDR 0xfffff400 /* Port A direction reg */ | |
| 355 | #define PADATA_ADDR 0xfffff401 /* Port A data register */ | |
| 356 | #define PAPUEN_ADDR 0xfffff402 /* Port A Pull-Up enable reg */ | |
| 357 | ||
| 358 | #define PADIR BYTE_REF(PADIR_ADDR) | |
| 359 | #define PADATA BYTE_REF(PADATA_ADDR) | |
| 360 | #define PAPUEN BYTE_REF(PAPUEN_ADDR) | |
| 361 | ||
| 362 | #define PA(x) (1 << (x)) | |
| 363 | ||
| 364 | /* | |
| 365 | * Port B | |
| 366 | */ | |
| 367 | #define PBDIR_ADDR 0xfffff408 /* Port B direction reg */ | |
| 368 | #define PBDATA_ADDR 0xfffff409 /* Port B data register */ | |
| 369 | #define PBPUEN_ADDR 0xfffff40a /* Port B Pull-Up enable reg */ | |
| 370 | #define PBSEL_ADDR 0xfffff40b /* Port B Select Register */ | |
| 371 | ||
| 372 | #define PBDIR BYTE_REF(PBDIR_ADDR) | |
| 373 | #define PBDATA BYTE_REF(PBDATA_ADDR) | |
| 374 | #define PBPUEN BYTE_REF(PBPUEN_ADDR) | |
| 375 | #define PBSEL BYTE_REF(PBSEL_ADDR) | |
| 376 | ||
| 377 | #define PB(x) (1 << (x)) | |
| 378 | ||
| 379 | #define PB_CSB0 0x01 /* Use CSB0 as PB[0] */ | |
| 380 | #define PB_CSB1 0x02 /* Use CSB1 as PB[1] */ | |
| 381 | #define PB_CSC0_RAS0 0x04 /* Use CSC0/RAS0 as PB[2] */ | |
| 382 | #define PB_CSC1_RAS1 0x08 /* Use CSC1/RAS1 as PB[3] */ | |
| 383 | #define PB_CSD0_CAS0 0x10 /* Use CSD0/CAS0 as PB[4] */ | |
| 384 | #define PB_CSD1_CAS1 0x20 /* Use CSD1/CAS1 as PB[5] */ | |
| 385 | #define PB_TIN_TOUT 0x40 /* Use TIN/TOUT as PB[6] */ | |
| 386 | #define PB_PWMO 0x80 /* Use PWMO as PB[7] */ | |
| 387 | ||
| 388 | /* | |
| 389 | * Port C | |
| 390 | */ | |
| 391 | #define PCDIR_ADDR 0xfffff410 /* Port C direction reg */ | |
| 392 | #define PCDATA_ADDR 0xfffff411 /* Port C data register */ | |
| 393 | #define PCPDEN_ADDR 0xfffff412 /* Port C Pull-Down enb. reg */ | |
| 394 | #define PCSEL_ADDR 0xfffff413 /* Port C Select Register */ | |
| 395 | ||
| 396 | #define PCDIR BYTE_REF(PCDIR_ADDR) | |
| 397 | #define PCDATA BYTE_REF(PCDATA_ADDR) | |
| 398 | #define PCPDEN BYTE_REF(PCPDEN_ADDR) | |
| 399 | #define PCSEL BYTE_REF(PCSEL_ADDR) | |
| 400 | ||
| 401 | #define PC(x) (1 << (x)) | |
| 402 | ||
| 403 | #define PC_LD0 0x01 /* Use LD0 as PC[0] */ | |
| 404 | #define PC_LD1 0x02 /* Use LD1 as PC[1] */ | |
| 405 | #define PC_LD2 0x04 /* Use LD2 as PC[2] */ | |
| 406 | #define PC_LD3 0x08 /* Use LD3 as PC[3] */ | |
| 407 | #define PC_LFLM 0x10 /* Use LFLM as PC[4] */ | |
| 408 | #define PC_LLP 0x20 /* Use LLP as PC[5] */ | |
| 409 | #define PC_LCLK 0x40 /* Use LCLK as PC[6] */ | |
| 410 | #define PC_LACD 0x80 /* Use LACD as PC[7] */ | |
| 411 | ||
| 412 | /* | |
| 413 | * Port D | |
| 414 | */ | |
| 415 | #define PDDIR_ADDR 0xfffff418 /* Port D direction reg */ | |
| 416 | #define PDDATA_ADDR 0xfffff419 /* Port D data register */ | |
| 417 | #define PDPUEN_ADDR 0xfffff41a /* Port D Pull-Up enable reg */ | |
| 418 | #define PDSEL_ADDR 0xfffff41b /* Port D Select Register */ | |
| 419 | #define PDPOL_ADDR 0xfffff41c /* Port D Polarity Register */ | |
| 420 | #define PDIRQEN_ADDR 0xfffff41d /* Port D IRQ enable register */ | |
| 421 | #define PDKBEN_ADDR 0xfffff41e /* Port D Keyboard Enable reg */ | |
| 422 | #define PDIQEG_ADDR 0xfffff41f /* Port D IRQ Edge Register */ | |
| 423 | ||
| 424 | #define PDDIR BYTE_REF(PDDIR_ADDR) | |
| 425 | #define PDDATA BYTE_REF(PDDATA_ADDR) | |
| 426 | #define PDPUEN BYTE_REF(PDPUEN_ADDR) | |
| 427 | #define PDSEL BYTE_REF(PDSEL_ADDR) | |
| 428 | #define PDPOL BYTE_REF(PDPOL_ADDR) | |
| 429 | #define PDIRQEN BYTE_REF(PDIRQEN_ADDR) | |
| 430 | #define PDKBEN BYTE_REF(PDKBEN_ADDR) | |
| 431 | #define PDIQEG BYTE_REF(PDIQEG_ADDR) | |
| 432 | ||
| 433 | #define PD(x) (1 << (x)) | |
| 434 | ||
| 435 | #define PD_INT0 0x01 /* Use INT0 as PD[0] */ | |
| 436 | #define PD_INT1 0x02 /* Use INT1 as PD[1] */ | |
| 437 | #define PD_INT2 0x04 /* Use INT2 as PD[2] */ | |
| 438 | #define PD_INT3 0x08 /* Use INT3 as PD[3] */ | |
| 439 | #define PD_IRQ1 0x10 /* Use IRQ1 as PD[4] */ | |
| 440 | #define PD_IRQ2 0x20 /* Use IRQ2 as PD[5] */ | |
| 441 | #define PD_IRQ3 0x40 /* Use IRQ3 as PD[6] */ | |
| 442 | #define PD_IRQ6 0x80 /* Use IRQ6 as PD[7] */ | |
| 443 | ||
| 444 | /* | |
| 445 | * Port E | |
| 446 | */ | |
| 447 | #define PEDIR_ADDR 0xfffff420 /* Port E direction reg */ | |
| 448 | #define PEDATA_ADDR 0xfffff421 /* Port E data register */ | |
| 449 | #define PEPUEN_ADDR 0xfffff422 /* Port E Pull-Up enable reg */ | |
| 450 | #define PESEL_ADDR 0xfffff423 /* Port E Select Register */ | |
| 451 | ||
| 452 | #define PEDIR BYTE_REF(PEDIR_ADDR) | |
| 453 | #define PEDATA BYTE_REF(PEDATA_ADDR) | |
| 454 | #define PEPUEN BYTE_REF(PEPUEN_ADDR) | |
| 455 | #define PESEL BYTE_REF(PESEL_ADDR) | |
| 456 | ||
| 457 | #define PE(x) (1 << (x)) | |
| 458 | ||
| 459 | #define PE_SPMTXD 0x01 /* Use SPMTXD as PE[0] */ | |
| 460 | #define PE_SPMRXD 0x02 /* Use SPMRXD as PE[1] */ | |
| 461 | #define PE_SPMCLK 0x04 /* Use SPMCLK as PE[2] */ | |
| 462 | #define PE_DWE 0x08 /* Use DWE as PE[3] */ | |
| 463 | #define PE_RXD 0x10 /* Use RXD as PE[4] */ | |
| 464 | #define PE_TXD 0x20 /* Use TXD as PE[5] */ | |
| 465 | #define PE_RTS 0x40 /* Use RTS as PE[6] */ | |
| 466 | #define PE_CTS 0x80 /* Use CTS as PE[7] */ | |
| 467 | ||
| 468 | /* | |
| 469 | * Port F | |
| 470 | */ | |
| 471 | #define PFDIR_ADDR 0xfffff428 /* Port F direction reg */ | |
| 472 | #define PFDATA_ADDR 0xfffff429 /* Port F data register */ | |
| 473 | #define PFPUEN_ADDR 0xfffff42a /* Port F Pull-Up enable reg */ | |
| 474 | #define PFSEL_ADDR 0xfffff42b /* Port F Select Register */ | |
| 475 | ||
| 476 | #define PFDIR BYTE_REF(PFDIR_ADDR) | |
| 477 | #define PFDATA BYTE_REF(PFDATA_ADDR) | |
| 478 | #define PFPUEN BYTE_REF(PFPUEN_ADDR) | |
| 479 | #define PFSEL BYTE_REF(PFSEL_ADDR) | |
| 480 | ||
| 481 | #define PF(x) (1 << (x)) | |
| 482 | ||
| 483 | #define PF_LCONTRAST 0x01 /* Use LCONTRAST as PF[0] */ | |
| 484 | #define PF_IRQ5 0x02 /* Use IRQ5 as PF[1] */ | |
| 485 | #define PF_CLKO 0x04 /* Use CLKO as PF[2] */ | |
| 486 | #define PF_A20 0x08 /* Use A20 as PF[3] */ | |
| 487 | #define PF_A21 0x10 /* Use A21 as PF[4] */ | |
| 488 | #define PF_A22 0x20 /* Use A22 as PF[5] */ | |
| 489 | #define PF_A23 0x40 /* Use A23 as PF[6] */ | |
| 490 | #define PF_CSA1 0x80 /* Use CSA1 as PF[7] */ | |
| 491 | ||
| 492 | /* | |
| 493 | * Port G | |
| 494 | */ | |
| 495 | #define PGDIR_ADDR 0xfffff430 /* Port G direction reg */ | |
| 496 | #define PGDATA_ADDR 0xfffff431 /* Port G data register */ | |
| 497 | #define PGPUEN_ADDR 0xfffff432 /* Port G Pull-Up enable reg */ | |
| 498 | #define PGSEL_ADDR 0xfffff433 /* Port G Select Register */ | |
| 499 | ||
| 500 | #define PGDIR BYTE_REF(PGDIR_ADDR) | |
| 501 | #define PGDATA BYTE_REF(PGDATA_ADDR) | |
| 502 | #define PGPUEN BYTE_REF(PGPUEN_ADDR) | |
| 503 | #define PGSEL BYTE_REF(PGSEL_ADDR) | |
| 504 | ||
| 505 | #define PG(x) (1 << (x)) | |
| 506 | ||
| 507 | #define PG_BUSW_DTACK 0x01 /* Use BUSW/DTACK as PG[0] */ | |
| 508 | #define PG_A0 0x02 /* Use A0 as PG[1] */ | |
| 509 | #define PG_EMUIRQ 0x04 /* Use EMUIRQ as PG[2] */ | |
| 510 | #define PG_HIZ_P_D 0x08 /* Use HIZ/P/D as PG[3] */ | |
| 511 | #define PG_EMUCS 0x10 /* Use EMUCS as PG[4] */ | |
| 512 | #define PG_EMUBRK 0x20 /* Use EMUBRK as PG[5] */ | |
| 513 | ||
| 514 | /* | |
| 515 | * Port J | |
| 516 | */ | |
| 517 | #define PJDIR_ADDR 0xfffff438 /* Port J direction reg */ | |
| 518 | #define PJDATA_ADDR 0xfffff439 /* Port J data register */ | |
| 519 | #define PJPUEN_ADDR 0xfffff43A /* Port J Pull-Up enb. reg */ | |
| 520 | #define PJSEL_ADDR 0xfffff43B /* Port J Select Register */ | |
| 521 | ||
| 522 | #define PJDIR BYTE_REF(PJDIR_ADDR) | |
| 523 | #define PJDATA BYTE_REF(PJDATA_ADDR) | |
| 524 | #define PJPUEN BYTE_REF(PJPUEN_ADDR) | |
| 525 | #define PJSEL BYTE_REF(PJSEL_ADDR) | |
| 526 | ||
| 527 | #define PJ(x) (1 << (x)) | |
| 528 | ||
| 529 | /* | |
| 530 | * Port K | |
| 531 | */ | |
| 532 | #define PKDIR_ADDR 0xfffff440 /* Port K direction reg */ | |
| 533 | #define PKDATA_ADDR 0xfffff441 /* Port K data register */ | |
| 534 | #define PKPUEN_ADDR 0xfffff442 /* Port K Pull-Up enb. reg */ | |
| 535 | #define PKSEL_ADDR 0xfffff443 /* Port K Select Register */ | |
| 536 | ||
| 537 | #define PKDIR BYTE_REF(PKDIR_ADDR) | |
| 538 | #define PKDATA BYTE_REF(PKDATA_ADDR) | |
| 539 | #define PKPUEN BYTE_REF(PKPUEN_ADDR) | |
| 540 | #define PKSEL BYTE_REF(PKSEL_ADDR) | |
| 541 | ||
| 542 | #define PK(x) (1 << (x)) | |
| 543 | ||
| 544 | #define PK_DATAREADY 0x01 /* Use ~DATA_READY as PK[0] */ | |
| 545 | #define PK_PWM2 0x01 /* Use PWM2 as PK[0] */ | |
| 546 | #define PK_R_W 0x02 /* Use R/W as PK[1] */ | |
| 547 | #define PK_LDS 0x04 /* Use /LDS as PK[2] */ | |
| 548 | #define PK_UDS 0x08 /* Use /UDS as PK[3] */ | |
| 549 | #define PK_LD4 0x10 /* Use LD4 as PK[4] */ | |
| 550 | #define PK_LD5 0x20 /* Use LD5 as PK[5] */ | |
| 551 | #define PK_LD6 0x40 /* Use LD6 as PK[6] */ | |
| 552 | #define PK_LD7 0x80 /* Use LD7 as PK[7] */ | |
| 553 | ||
| 554 | #define PJDIR_ADDR 0xfffff438 /* Port J direction reg */ | |
| 555 | #define PJDATA_ADDR 0xfffff439 /* Port J data register */ | |
| 556 | #define PJPUEN_ADDR 0xfffff43A /* Port J Pull-Up enable reg */ | |
| 557 | #define PJSEL_ADDR 0xfffff43B /* Port J Select Register */ | |
| 558 | ||
| 559 | #define PJDIR BYTE_REF(PJDIR_ADDR) | |
| 560 | #define PJDATA BYTE_REF(PJDATA_ADDR) | |
| 561 | #define PJPUEN BYTE_REF(PJPUEN_ADDR) | |
| 562 | #define PJSEL BYTE_REF(PJSEL_ADDR) | |
| 563 | ||
| 564 | #define PJ(x) (1 << (x)) | |
| 565 | ||
| 566 | #define PJ_MOSI 0x01 /* Use MOSI as PJ[0] */ | |
| 567 | #define PJ_MISO 0x02 /* Use MISO as PJ[1] */ | |
| 568 | #define PJ_SPICLK1 0x04 /* Use SPICLK1 as PJ[2] */ | |
| 569 | #define PJ_SS 0x08 /* Use SS as PJ[3] */ | |
| 570 | #define PJ_RXD2 0x10 /* Use RXD2 as PJ[4] */ | |
| 571 | #define PJ_TXD2 0x20 /* Use TXD2 as PJ[5] */ | |
| 572 | #define PJ_RTS2 0x40 /* Use RTS2 as PJ[5] */ | |
| 573 | #define PJ_CTS2 0x80 /* Use CTS2 as PJ[5] */ | |
| 574 | ||
| 575 | /* | |
| 576 | * Port M | |
| 577 | */ | |
| 578 | #define PMDIR_ADDR 0xfffff448 /* Port M direction reg */ | |
| 579 | #define PMDATA_ADDR 0xfffff449 /* Port M data register */ | |
| 580 | #define PMPUEN_ADDR 0xfffff44a /* Port M Pull-Up enable reg */ | |
| 581 | #define PMSEL_ADDR 0xfffff44b /* Port M Select Register */ | |
| 582 | ||
| 583 | #define PMDIR BYTE_REF(PMDIR_ADDR) | |
| 584 | #define PMDATA BYTE_REF(PMDATA_ADDR) | |
| 585 | #define PMPUEN BYTE_REF(PMPUEN_ADDR) | |
| 586 | #define PMSEL BYTE_REF(PMSEL_ADDR) | |
| 587 | ||
| 588 | #define PM(x) (1 << (x)) | |
| 589 | ||
| 590 | #define PM_SDCLK 0x01 /* Use SDCLK as PM[0] */ | |
| 591 | #define PM_SDCE 0x02 /* Use SDCE as PM[1] */ | |
| 592 | #define PM_DQMH 0x04 /* Use DQMH as PM[2] */ | |
| 593 | #define PM_DQML 0x08 /* Use DQML as PM[3] */ | |
| 594 | #define PM_SDA10 0x10 /* Use SDA10 as PM[4] */ | |
| 595 | #define PM_DMOE 0x20 /* Use DMOE as PM[5] */ | |
| 596 | ||
| 597 | /********** | |
| 598 | * | |
| 599 | * 0xFFFFF5xx -- Pulse-Width Modulator (PWM) | |
| 600 | * | |
| 601 | **********/ | |
| 602 | ||
| 603 | /* | |
| 604 | * PWM Control Register | |
| 605 | */ | |
| 606 | #define PWMC_ADDR 0xfffff500 | |
| 607 | #define PWMC WORD_REF(PWMC_ADDR) | |
| 608 | ||
| 609 | #define PWMC_CLKSEL_MASK 0x0003 /* Clock Selection */ | |
| 610 | #define PWMC_CLKSEL_SHIFT 0 | |
| 611 | #define PWMC_REPEAT_MASK 0x000c /* Sample Repeats */ | |
| 612 | #define PWMC_REPEAT_SHIFT 2 | |
| 613 | #define PWMC_EN 0x0010 /* Enable PWM */ | |
| 614 | #define PMNC_FIFOAV 0x0020 /* FIFO Available */ | |
| 615 | #define PWMC_IRQEN 0x0040 /* Interrupt Request Enable */ | |
| 616 | #define PWMC_IRQ 0x0080 /* Interrupt Request (FIFO empty) */ | |
| 617 | #define PWMC_PRESCALER_MASK 0x7f00 /* Incoming Clock prescaler */ | |
| 618 | #define PWMC_PRESCALER_SHIFT 8 | |
| 619 | #define PWMC_CLKSRC 0x8000 /* Clock Source Select */ | |
| 620 | ||
| 621 | /* '328-compatible definitions */ | |
| 622 | #define PWMC_PWMEN PWMC_EN | |
| 623 | ||
| 624 | /* | |
| 625 | * PWM Sample Register | |
| 626 | */ | |
| 627 | #define PWMS_ADDR 0xfffff502 | |
| 628 | #define PWMS WORD_REF(PWMS_ADDR) | |
| 629 | ||
| 630 | /* | |
| 631 | * PWM Period Register | |
| 632 | */ | |
| 633 | #define PWMP_ADDR 0xfffff504 | |
| 634 | #define PWMP BYTE_REF(PWMP_ADDR) | |
| 635 | ||
| 636 | /* | |
| 637 | * PWM Counter Register | |
| 638 | */ | |
| 639 | #define PWMCNT_ADDR 0xfffff505 | |
| 640 | #define PWMCNT BYTE_REF(PWMCNT_ADDR) | |
| 641 | ||
| 642 | /********** | |
| 643 | * | |
| 644 | * 0xFFFFF6xx -- General-Purpose Timer | |
| 645 | * | |
| 646 | **********/ | |
| 647 | ||
| 648 | /* | |
| 649 | * Timer Control register | |
| 650 | */ | |
| 651 | #define TCTL_ADDR 0xfffff600 | |
| 652 | #define TCTL WORD_REF(TCTL_ADDR) | |
| 653 | ||
| 654 | #define TCTL_TEN 0x0001 /* Timer Enable */ | |
| 655 | #define TCTL_CLKSOURCE_MASK 0x000e /* Clock Source: */ | |
| 656 | #define TCTL_CLKSOURCE_STOP 0x0000 /* Stop count (disabled) */ | |
| 657 | #define TCTL_CLKSOURCE_SYSCLK 0x0002 /* SYSCLK to prescaler */ | |
| 658 | #define TCTL_CLKSOURCE_SYSCLK_16 0x0004 /* SYSCLK/16 to prescaler */ | |
| 659 | #define TCTL_CLKSOURCE_TIN 0x0006 /* TIN to prescaler */ | |
| 660 | #define TCTL_CLKSOURCE_32KHZ 0x0008 /* 32kHz clock to prescaler */ | |
| 661 | #define TCTL_IRQEN 0x0010 /* IRQ Enable */ | |
| 662 | #define TCTL_OM 0x0020 /* Output Mode */ | |
| 663 | #define TCTL_CAP_MASK 0x00c0 /* Capture Edge: */ | |
| 664 | #define TCTL_CAP_RE 0x0040 /* Capture on rizing edge */ | |
| 665 | #define TCTL_CAP_FE 0x0080 /* Capture on falling edge */ | |
| 666 | #define TCTL_FRR 0x0010 /* Free-Run Mode */ | |
| 667 | ||
| 668 | /* '328-compatible definitions */ | |
| 669 | #define TCTL1_ADDR TCTL_ADDR | |
| 670 | #define TCTL1 TCTL | |
| 671 | ||
| 672 | /* | |
| 673 | * Timer Prescaler Register | |
| 674 | */ | |
| 675 | #define TPRER_ADDR 0xfffff602 | |
| 676 | #define TPRER WORD_REF(TPRER_ADDR) | |
| 677 | ||
| 678 | /* '328-compatible definitions */ | |
| 679 | #define TPRER1_ADDR TPRER_ADDR | |
| 680 | #define TPRER1 TPRER | |
| 681 | ||
| 682 | /* | |
| 683 | * Timer Compare Register | |
| 684 | */ | |
| 685 | #define TCMP_ADDR 0xfffff604 | |
| 686 | #define TCMP WORD_REF(TCMP_ADDR) | |
| 687 | ||
| 688 | /* '328-compatible definitions */ | |
| 689 | #define TCMP1_ADDR TCMP_ADDR | |
| 690 | #define TCMP1 TCMP | |
| 691 | ||
| 692 | /* | |
| 693 | * Timer Capture register | |
| 694 | */ | |
| 695 | #define TCR_ADDR 0xfffff606 | |
| 696 | #define TCR WORD_REF(TCR_ADDR) | |
| 697 | ||
| 698 | /* '328-compatible definitions */ | |
| 699 | #define TCR1_ADDR TCR_ADDR | |
| 700 | #define TCR1 TCR | |
| 701 | ||
| 702 | /* | |
| 703 | * Timer Counter Register | |
| 704 | */ | |
| 705 | #define TCN_ADDR 0xfffff608 | |
| 706 | #define TCN WORD_REF(TCN_ADDR) | |
| 707 | ||
| 708 | /* '328-compatible definitions */ | |
| 709 | #define TCN1_ADDR TCN_ADDR | |
| 710 | #define TCN1 TCN | |
| 711 | ||
| 712 | /* | |
| 713 | * Timer Status Register | |
| 714 | */ | |
| 715 | #define TSTAT_ADDR 0xfffff60a | |
| 716 | #define TSTAT WORD_REF(TSTAT_ADDR) | |
| 717 | ||
| 718 | #define TSTAT_COMP 0x0001 /* Compare Event occurred */ | |
| 719 | #define TSTAT_CAPT 0x0001 /* Capture Event occurred */ | |
| 720 | ||
| 721 | /* '328-compatible definitions */ | |
| 722 | #define TSTAT1_ADDR TSTAT_ADDR | |
| 723 | #define TSTAT1 TSTAT | |
| 724 | ||
| 725 | /********** | |
| 726 | * | |
| 727 | * 0xFFFFF8xx -- Serial Periferial Interface Master (SPIM) | |
| 728 | * | |
| 729 | **********/ | |
| 730 | ||
| 731 | /* | |
| 732 | * SPIM Data Register | |
| 733 | */ | |
| 734 | #define SPIMDATA_ADDR 0xfffff800 | |
| 735 | #define SPIMDATA WORD_REF(SPIMDATA_ADDR) | |
| 736 | ||
| 737 | /* | |
| 738 | * SPIM Control/Status Register | |
| 739 | */ | |
| 740 | #define SPIMCONT_ADDR 0xfffff802 | |
| 741 | #define SPIMCONT WORD_REF(SPIMCONT_ADDR) | |
| 742 | ||
| 743 | #define SPIMCONT_BIT_COUNT_MASK 0x000f /* Transfer Length in Bytes */ | |
| 744 | #define SPIMCONT_BIT_COUNT_SHIFT 0 | |
| 745 | #define SPIMCONT_POL 0x0010 /* SPMCLK Signel Polarity */ | |
| 746 | #define SPIMCONT_PHA 0x0020 /* Clock/Data phase relationship */ | |
| 747 | #define SPIMCONT_IRQEN 0x0040 /* IRQ Enable */ | |
| 748 | #define SPIMCONT_IRQ 0x0080 /* Interrupt Request */ | |
| 749 | #define SPIMCONT_XCH 0x0100 /* Exchange */ | |
| 750 | #define SPIMCONT_ENABLE 0x0200 /* Enable SPIM */ | |
| 751 | #define SPIMCONT_DATA_RATE_MASK 0xe000 /* SPIM Data Rate */ | |
| 752 | #define SPIMCONT_DATA_RATE_SHIFT 13 | |
| 753 | ||
| 754 | /* '328-compatible definitions */ | |
| 755 | #define SPIMCONT_SPIMIRQ SPIMCONT_IRQ | |
| 756 | #define SPIMCONT_SPIMEN SPIMCONT_ENABLE | |
| 757 | ||
| 758 | /********** | |
| 759 | * | |
| 760 | * 0xFFFFF9xx -- UART | |
| 761 | * | |
| 762 | **********/ | |
| 763 | ||
| 764 | /* | |
| 765 | * UART Status/Control Register | |
| 766 | */ | |
| 767 | ||
| 768 | #define USTCNT_ADDR 0xfffff900 | |
| 769 | #define USTCNT WORD_REF(USTCNT_ADDR) | |
| 770 | ||
| 771 | #define USTCNT_TXAE 0x0001 /* Transmitter Available Interrupt Enable */ | |
| 772 | #define USTCNT_TXHE 0x0002 /* Transmitter Half Empty Enable */ | |
| 773 | #define USTCNT_TXEE 0x0004 /* Transmitter Empty Interrupt Enable */ | |
| 774 | #define USTCNT_RXRE 0x0008 /* Receiver Ready Interrupt Enable */ | |
| 775 | #define USTCNT_RXHE 0x0010 /* Receiver Half-Full Interrupt Enable */ | |
| 776 | #define USTCNT_RXFE 0x0020 /* Receiver Full Interrupt Enable */ | |
| 777 | #define USTCNT_CTSD 0x0040 /* CTS Delta Interrupt Enable */ | |
| 778 | #define USTCNT_ODEN 0x0080 /* Old Data Interrupt Enable */ | |
| 779 | #define USTCNT_8_7 0x0100 /* Eight or seven-bit transmission */ | |
| 780 | #define USTCNT_STOP 0x0200 /* Stop bit transmission */ | |
| 781 | #define USTCNT_ODD 0x0400 /* Odd Parity */ | |
| 782 | #define USTCNT_PEN 0x0800 /* Parity Enable */ | |
| 783 | #define USTCNT_CLKM 0x1000 /* Clock Mode Select */ | |
| 784 | #define USTCNT_TXEN 0x2000 /* Transmitter Enable */ | |
| 785 | #define USTCNT_RXEN 0x4000 /* Receiver Enable */ | |
| 786 | #define USTCNT_UEN 0x8000 /* UART Enable */ | |
| 787 | ||
| 788 | /* '328-compatible definitions */ | |
| 789 | #define USTCNT_TXAVAILEN USTCNT_TXAE | |
| 790 | #define USTCNT_TXHALFEN USTCNT_TXHE | |
| 791 | #define USTCNT_TXEMPTYEN USTCNT_TXEE | |
| 792 | #define USTCNT_RXREADYEN USTCNT_RXRE | |
| 793 | #define USTCNT_RXHALFEN USTCNT_RXHE | |
| 794 | #define USTCNT_RXFULLEN USTCNT_RXFE | |
| 795 | #define USTCNT_CTSDELTAEN USTCNT_CTSD | |
| 796 | #define USTCNT_ODD_EVEN USTCNT_ODD | |
| 797 | #define USTCNT_PARITYEN USTCNT_PEN | |
| 798 | #define USTCNT_CLKMODE USTCNT_CLKM | |
| 799 | #define USTCNT_UARTEN USTCNT_UEN | |
| 800 | ||
| 801 | /* | |
| 802 | * UART Baud Control Register | |
| 803 | */ | |
| 804 | #define UBAUD_ADDR 0xfffff902 | |
| 805 | #define UBAUD WORD_REF(UBAUD_ADDR) | |
| 806 | ||
| 807 | #define UBAUD_PRESCALER_MASK 0x003f /* Actual divisor is 65 - PRESCALER */ | |
| 808 | #define UBAUD_PRESCALER_SHIFT 0 | |
| 809 | #define UBAUD_DIVIDE_MASK 0x0700 /* Baud Rate freq. divizor */ | |
| 810 | #define UBAUD_DIVIDE_SHIFT 8 | |
| 811 | #define UBAUD_BAUD_SRC 0x0800 /* Baud Rate Source */ | |
| 812 | #define UBAUD_UCLKDIR 0x2000 /* UCLK Direction */ | |
| 813 | ||
| 814 | /* | |
| 815 | * UART Receiver Register | |
| 816 | */ | |
| 817 | #define URX_ADDR 0xfffff904 | |
| 818 | #define URX WORD_REF(URX_ADDR) | |
| 819 | ||
| 820 | #define URX_RXDATA_ADDR 0xfffff905 | |
| 821 | #define URX_RXDATA BYTE_REF(URX_RXDATA_ADDR) | |
| 822 | ||
| 823 | #define URX_RXDATA_MASK 0x00ff /* Received data */ | |
| 824 | #define URX_RXDATA_SHIFT 0 | |
| 825 | #define URX_PARITY_ERROR 0x0100 /* Parity Error */ | |
| 826 | #define URX_BREAK 0x0200 /* Break Detected */ | |
| 827 | #define URX_FRAME_ERROR 0x0400 /* Framing Error */ | |
| 828 | #define URX_OVRUN 0x0800 /* Serial Overrun */ | |
| 829 | #define URX_OLD_DATA 0x1000 /* Old data in FIFO */ | |
| 830 | #define URX_DATA_READY 0x2000 /* Data Ready (FIFO not empty) */ | |
| 831 | #define URX_FIFO_HALF 0x4000 /* FIFO is Half-Full */ | |
| 832 | #define URX_FIFO_FULL 0x8000 /* FIFO is Full */ | |
| 833 | ||
| 834 | /* | |
| 835 | * UART Transmitter Register | |
| 836 | */ | |
| 837 | #define UTX_ADDR 0xfffff906 | |
| 838 | #define UTX WORD_REF(UTX_ADDR) | |
| 839 | ||
| 840 | #define UTX_TXDATA_ADDR 0xfffff907 | |
| 841 | #define UTX_TXDATA BYTE_REF(UTX_TXDATA_ADDR) | |
| 842 | ||
| 843 | #define UTX_TXDATA_MASK 0x00ff /* Data to be transmitted */ | |
| 844 | #define UTX_TXDATA_SHIFT 0 | |
| 845 | #define UTX_CTS_DELTA 0x0100 /* CTS changed */ | |
| 846 | #define UTX_CTS_STAT 0x0200 /* CTS State */ | |
| 847 | #define UTX_BUSY 0x0400 /* FIFO is busy, sending a character */ | |
| 848 | #define UTX_NOCTS 0x0800 /* Ignore CTS */ | |
| 849 | #define UTX_SEND_BREAK 0x1000 /* Send a BREAK */ | |
| 850 | #define UTX_TX_AVAIL 0x2000 /* Transmit FIFO has a slot available */ | |
| 851 | #define UTX_FIFO_HALF 0x4000 /* Transmit FIFO is half empty */ | |
| 852 | #define UTX_FIFO_EMPTY 0x8000 /* Transmit FIFO is empty */ | |
| 853 | ||
| 854 | /* '328-compatible definitions */ | |
| 855 | #define UTX_CTS_STATUS UTX_CTS_STAT | |
| 856 | #define UTX_IGNORE_CTS UTX_NOCTS | |
| 857 | ||
| 858 | /* | |
| 859 | * UART Miscellaneous Register | |
| 860 | */ | |
| 861 | #define UMISC_ADDR 0xfffff908 | |
| 862 | #define UMISC WORD_REF(UMISC_ADDR) | |
| 863 | ||
| 864 | #define UMISC_TX_POL 0x0004 /* Transmit Polarity */ | |
| 865 | #define UMISC_RX_POL 0x0008 /* Receive Polarity */ | |
| 866 | #define UMISC_IRDA_LOOP 0x0010 /* IrDA Loopback Enable */ | |
| 867 | #define UMISC_IRDA_EN 0x0020 /* Infra-Red Enable */ | |
| 868 | #define UMISC_RTS 0x0040 /* Set RTS status */ | |
| 869 | #define UMISC_RTSCONT 0x0080 /* Choose RTS control */ | |
| 870 | #define UMISC_IR_TEST 0x0400 /* IRDA Test Enable */ | |
| 871 | #define UMISC_BAUD_RESET 0x0800 /* Reset Baud Rate Generation Counters */ | |
| 872 | #define UMISC_LOOP 0x1000 /* Serial Loopback Enable */ | |
| 873 | #define UMISC_FORCE_PERR 0x2000 /* Force Parity Error */ | |
| 874 | #define UMISC_CLKSRC 0x4000 /* Clock Source */ | |
| 875 | #define UMISC_BAUD_TEST 0x8000 /* Enable Baud Test Mode */ | |
| 876 | ||
| 877 | /* | |
| 878 | * UART Non-integer Prescaler Register | |
| 879 | */ | |
| 880 | #define NIPR_ADDR 0xfffff90a | |
| 881 | #define NIPR WORD_REF(NIPR_ADDR) | |
| 882 | ||
| 883 | #define NIPR_STEP_VALUE_MASK 0x00ff /* NI prescaler step value */ | |
| 884 | #define NIPR_STEP_VALUE_SHIFT 0 | |
| 885 | #define NIPR_SELECT_MASK 0x0700 /* Tap Selection */ | |
| 886 | #define NIPR_SELECT_SHIFT 8 | |
| 887 | #define NIPR_PRE_SEL 0x8000 /* Non-integer prescaler select */ | |
| 888 | ||
| 889 | ||
| 890 | /* generalization of uart control registers to support multiple ports: */ | |
| 891 | typedef struct { | |
| 892 | volatile unsigned short int ustcnt; | |
| 893 | volatile unsigned short int ubaud; | |
| 894 | union { | |
| 895 | volatile unsigned short int w; | |
| 896 | struct { | |
| 897 | volatile unsigned char status; | |
| 898 | volatile unsigned char rxdata; | |
| 899 | } b; | |
| 900 | } urx; | |
| 901 | union { | |
| 902 | volatile unsigned short int w; | |
| 903 | struct { | |
| 904 | volatile unsigned char status; | |
| 905 | volatile unsigned char txdata; | |
| 906 | } b; | |
| 907 | } utx; | |
| 908 | volatile unsigned short int umisc; | |
| 909 | volatile unsigned short int nipr; | |
| 910 | volatile unsigned short int hmark; | |
| 911 | volatile unsigned short int unused; | |
| f78fc874 | 912 | } __attribute__((packed)) m68328_uart; |
| 1da177e4 LT |
913 | |
| 914 | ||
| 915 | ||
| 916 | ||
| 917 | /********** | |
| 918 | * | |
| 919 | * 0xFFFFFAxx -- LCD Controller | |
| 920 | * | |
| 921 | **********/ | |
| 922 | ||
| 923 | /* | |
| 924 | * LCD Screen Starting Address Register | |
| 925 | */ | |
| 926 | #define LSSA_ADDR 0xfffffa00 | |
| 927 | #define LSSA LONG_REF(LSSA_ADDR) | |
| 928 | ||
| 929 | #define LSSA_SSA_MASK 0x1ffffffe /* Bits 0 and 29-31 are reserved */ | |
| 930 | ||
| 931 | /* | |
| 932 | * LCD Virtual Page Width Register | |
| 933 | */ | |
| 934 | #define LVPW_ADDR 0xfffffa05 | |
| 935 | #define LVPW BYTE_REF(LVPW_ADDR) | |
| 936 | ||
| 937 | /* | |
| 938 | * LCD Screen Width Register (not compatible with '328 !!!) | |
| 939 | */ | |
| 940 | #define LXMAX_ADDR 0xfffffa08 | |
| 941 | #define LXMAX WORD_REF(LXMAX_ADDR) | |
| 942 | ||
| 943 | #define LXMAX_XM_MASK 0x02f0 /* Bits 0-3 and 10-15 are reserved */ | |
| 944 | ||
| 945 | /* | |
| 946 | * LCD Screen Height Register | |
| 947 | */ | |
| 948 | #define LYMAX_ADDR 0xfffffa0a | |
| 949 | #define LYMAX WORD_REF(LYMAX_ADDR) | |
| 950 | ||
| 951 | #define LYMAX_YM_MASK 0x01ff /* Bits 9-15 are reserved */ | |
| 952 | ||
| 953 | /* | |
| 954 | * LCD Cursor X Position Register | |
| 955 | */ | |
| 956 | #define LCXP_ADDR 0xfffffa18 | |
| 957 | #define LCXP WORD_REF(LCXP_ADDR) | |
| 958 | ||
| 959 | #define LCXP_CC_MASK 0xc000 /* Cursor Control */ | |
| 960 | #define LCXP_CC_TRAMSPARENT 0x0000 | |
| 961 | #define LCXP_CC_BLACK 0x4000 | |
| 962 | #define LCXP_CC_REVERSED 0x8000 | |
| 963 | #define LCXP_CC_WHITE 0xc000 | |
| 964 | #define LCXP_CXP_MASK 0x02ff /* Cursor X position */ | |
| 965 | ||
| 966 | /* | |
| 967 | * LCD Cursor Y Position Register | |
| 968 | */ | |
| 969 | #define LCYP_ADDR 0xfffffa1a | |
| 970 | #define LCYP WORD_REF(LCYP_ADDR) | |
| 971 | ||
| 972 | #define LCYP_CYP_MASK 0x01ff /* Cursor Y Position */ | |
| 973 | ||
| 974 | /* | |
| 975 | * LCD Cursor Width and Heigth Register | |
| 976 | */ | |
| 977 | #define LCWCH_ADDR 0xfffffa1c | |
| 978 | #define LCWCH WORD_REF(LCWCH_ADDR) | |
| 979 | ||
| 980 | #define LCWCH_CH_MASK 0x001f /* Cursor Height */ | |
| 981 | #define LCWCH_CH_SHIFT 0 | |
| 982 | #define LCWCH_CW_MASK 0x1f00 /* Cursor Width */ | |
| 983 | #define LCWCH_CW_SHIFT 8 | |
| 984 | ||
| 985 | /* | |
| 986 | * LCD Blink Control Register | |
| 987 | */ | |
| 988 | #define LBLKC_ADDR 0xfffffa1f | |
| 989 | #define LBLKC BYTE_REF(LBLKC_ADDR) | |
| 990 | ||
| 991 | #define LBLKC_BD_MASK 0x7f /* Blink Divisor */ | |
| 992 | #define LBLKC_BD_SHIFT 0 | |
| 993 | #define LBLKC_BKEN 0x80 /* Blink Enabled */ | |
| 994 | ||
| 995 | /* | |
| 996 | * LCD Panel Interface Configuration Register | |
| 997 | */ | |
| 998 | #define LPICF_ADDR 0xfffffa20 | |
| 999 | #define LPICF BYTE_REF(LPICF_ADDR) | |
| 1000 | ||
| 1001 | #define LPICF_GS_MASK 0x03 /* Gray-Scale Mode */ | |
| 1002 | #define LPICF_GS_BW 0x00 | |
| 1003 | #define LPICF_GS_GRAY_4 0x01 | |
| 1004 | #define LPICF_GS_GRAY_16 0x02 | |
| 1005 | #define LPICF_PBSIZ_MASK 0x0c /* Panel Bus Width */ | |
| 1006 | #define LPICF_PBSIZ_1 0x00 | |
| 1007 | #define LPICF_PBSIZ_2 0x04 | |
| 1008 | #define LPICF_PBSIZ_4 0x08 | |
| 1009 | ||
| 1010 | /* | |
| 1011 | * LCD Polarity Configuration Register | |
| 1012 | */ | |
| 1013 | #define LPOLCF_ADDR 0xfffffa21 | |
| 1014 | #define LPOLCF BYTE_REF(LPOLCF_ADDR) | |
| 1015 | ||
| 1016 | #define LPOLCF_PIXPOL 0x01 /* Pixel Polarity */ | |
| 1017 | #define LPOLCF_LPPOL 0x02 /* Line Pulse Polarity */ | |
| 1018 | #define LPOLCF_FLMPOL 0x04 /* Frame Marker Polarity */ | |
| 1019 | #define LPOLCF_LCKPOL 0x08 /* LCD Shift Lock Polarity */ | |
| 1020 | ||
| 1021 | /* | |
| 1022 | * LACD (LCD Alternate Crystal Direction) Rate Control Register | |
| 1023 | */ | |
| 1024 | #define LACDRC_ADDR 0xfffffa23 | |
| 1025 | #define LACDRC BYTE_REF(LACDRC_ADDR) | |
| 1026 | ||
| 1027 | #define LACDRC_ACDSLT 0x80 /* Signal Source Select */ | |
| 1028 | #define LACDRC_ACD_MASK 0x0f /* Alternate Crystal Direction Control */ | |
| 1029 | #define LACDRC_ACD_SHIFT 0 | |
| 1030 | ||
| 1031 | /* | |
| 1032 | * LCD Pixel Clock Divider Register | |
| 1033 | */ | |
| 1034 | #define LPXCD_ADDR 0xfffffa25 | |
| 1035 | #define LPXCD BYTE_REF(LPXCD_ADDR) | |
| 1036 | ||
| 1037 | #define LPXCD_PCD_MASK 0x3f /* Pixel Clock Divider */ | |
| 1038 | #define LPXCD_PCD_SHIFT 0 | |
| 1039 | ||
| 1040 | /* | |
| 1041 | * LCD Clocking Control Register | |
| 1042 | */ | |
| 1043 | #define LCKCON_ADDR 0xfffffa27 | |
| 1044 | #define LCKCON BYTE_REF(LCKCON_ADDR) | |
| 1045 | ||
| 1046 | #define LCKCON_DWS_MASK 0x0f /* Display Wait-State */ | |
| 1047 | #define LCKCON_DWS_SHIFT 0 | |
| 1048 | #define LCKCON_DWIDTH 0x40 /* Display Memory Width */ | |
| 1049 | #define LCKCON_LCDON 0x80 /* Enable LCD Controller */ | |
| 1050 | ||
| 1051 | /* '328-compatible definitions */ | |
| 1052 | #define LCKCON_DW_MASK LCKCON_DWS_MASK | |
| 1053 | #define LCKCON_DW_SHIFT LCKCON_DWS_SHIFT | |
| 1054 | ||
| 1055 | /* | |
| 1056 | * LCD Refresh Rate Adjustment Register | |
| 1057 | */ | |
| 1058 | #define LRRA_ADDR 0xfffffa29 | |
| 1059 | #define LRRA BYTE_REF(LRRA_ADDR) | |
| 1060 | ||
| 1061 | /* | |
| 1062 | * LCD Panning Offset Register | |
| 1063 | */ | |
| 1064 | #define LPOSR_ADDR 0xfffffa2d | |
| 1065 | #define LPOSR BYTE_REF(LPOSR_ADDR) | |
| 1066 | ||
| 1067 | #define LPOSR_POS_MASK 0x0f /* Pixel Offset Code */ | |
| 1068 | #define LPOSR_POS_SHIFT 0 | |
| 1069 | ||
| 1070 | /* | |
| 1071 | * LCD Frame Rate Control Modulation Register | |
| 1072 | */ | |
| 1073 | #define LFRCM_ADDR 0xfffffa31 | |
| 1074 | #define LFRCM BYTE_REF(LFRCM_ADDR) | |
| 1075 | ||
| 1076 | #define LFRCM_YMOD_MASK 0x0f /* Vertical Modulation */ | |
| 1077 | #define LFRCM_YMOD_SHIFT 0 | |
| 1078 | #define LFRCM_XMOD_MASK 0xf0 /* Horizontal Modulation */ | |
| 1079 | #define LFRCM_XMOD_SHIFT 4 | |
| 1080 | ||
| 1081 | /* | |
| 1082 | * LCD Gray Palette Mapping Register | |
| 1083 | */ | |
| 1084 | #define LGPMR_ADDR 0xfffffa33 | |
| 1085 | #define LGPMR BYTE_REF(LGPMR_ADDR) | |
| 1086 | ||
| 1087 | #define LGPMR_G1_MASK 0x0f | |
| 1088 | #define LGPMR_G1_SHIFT 0 | |
| 1089 | #define LGPMR_G2_MASK 0xf0 | |
| 1090 | #define LGPMR_G2_SHIFT 4 | |
| 1091 | ||
| 1092 | /* | |
| 1093 | * PWM Contrast Control Register | |
| 1094 | */ | |
| 1095 | #define PWMR_ADDR 0xfffffa36 | |
| 1096 | #define PWMR WORD_REF(PWMR_ADDR) | |
| 1097 | ||
| 1098 | #define PWMR_PW_MASK 0x00ff /* Pulse Width */ | |
| 1099 | #define PWMR_PW_SHIFT 0 | |
| 1100 | #define PWMR_CCPEN 0x0100 /* Contrast Control Enable */ | |
| 1101 | #define PWMR_SRC_MASK 0x0600 /* Input Clock Source */ | |
| 1102 | #define PWMR_SRC_LINE 0x0000 /* Line Pulse */ | |
| 1103 | #define PWMR_SRC_PIXEL 0x0200 /* Pixel Clock */ | |
| 1104 | #define PWMR_SRC_LCD 0x4000 /* LCD clock */ | |
| 1105 | ||
| 1106 | /********** | |
| 1107 | * | |
| 1108 | * 0xFFFFFBxx -- Real-Time Clock (RTC) | |
| 1109 | * | |
| 1110 | **********/ | |
| 1111 | ||
| 1112 | /* | |
| 1113 | * RTC Hours Minutes and Seconds Register | |
| 1114 | */ | |
| 1115 | #define RTCTIME_ADDR 0xfffffb00 | |
| 1116 | #define RTCTIME LONG_REF(RTCTIME_ADDR) | |
| 1117 | ||
| 1118 | #define RTCTIME_SECONDS_MASK 0x0000003f /* Seconds */ | |
| 1119 | #define RTCTIME_SECONDS_SHIFT 0 | |
| 1120 | #define RTCTIME_MINUTES_MASK 0x003f0000 /* Minutes */ | |
| 1121 | #define RTCTIME_MINUTES_SHIFT 16 | |
| 1122 | #define RTCTIME_HOURS_MASK 0x1f000000 /* Hours */ | |
| 1123 | #define RTCTIME_HOURS_SHIFT 24 | |
| 1124 | ||
| 1125 | /* | |
| 1126 | * RTC Alarm Register | |
| 1127 | */ | |
| 1128 | #define RTCALRM_ADDR 0xfffffb04 | |
| 1129 | #define RTCALRM LONG_REF(RTCALRM_ADDR) | |
| 1130 | ||
| 1131 | #define RTCALRM_SECONDS_MASK 0x0000003f /* Seconds */ | |
| 1132 | #define RTCALRM_SECONDS_SHIFT 0 | |
| 1133 | #define RTCALRM_MINUTES_MASK 0x003f0000 /* Minutes */ | |
| 1134 | #define RTCALRM_MINUTES_SHIFT 16 | |
| 1135 | #define RTCALRM_HOURS_MASK 0x1f000000 /* Hours */ | |
| 1136 | #define RTCALRM_HOURS_SHIFT 24 | |
| 1137 | ||
| 1138 | /* | |
| 1139 | * Watchdog Timer Register | |
| 1140 | */ | |
| 1141 | #define WATCHDOG_ADDR 0xfffffb0a | |
| 1142 | #define WATCHDOG WORD_REF(WATCHDOG_ADDR) | |
| 1143 | ||
| 1144 | #define WATCHDOG_EN 0x0001 /* Watchdog Enabled */ | |
| 1145 | #define WATCHDOG_ISEL 0x0002 /* Select the watchdog interrupt */ | |
| 1146 | #define WATCHDOG_INTF 0x0080 /* Watchdog interrupt occcured */ | |
| 1147 | #define WATCHDOG_CNT_MASK 0x0300 /* Watchdog Counter */ | |
| 1148 | #define WATCHDOG_CNT_SHIFT 8 | |
| 1149 | ||
| 1150 | /* | |
| 1151 | * RTC Control Register | |
| 1152 | */ | |
| 1153 | #define RTCCTL_ADDR 0xfffffb0c | |
| 1154 | #define RTCCTL WORD_REF(RTCCTL_ADDR) | |
| 1155 | ||
| 1156 | #define RTCCTL_XTL 0x0020 /* Crystal Selection */ | |
| 1157 | #define RTCCTL_EN 0x0080 /* RTC Enable */ | |
| 1158 | ||
| 1159 | /* '328-compatible definitions */ | |
| 1160 | #define RTCCTL_384 RTCCTL_XTL | |
| 1161 | #define RTCCTL_ENABLE RTCCTL_EN | |
| 1162 | ||
| 1163 | /* | |
| 1164 | * RTC Interrupt Status Register | |
| 1165 | */ | |
| 1166 | #define RTCISR_ADDR 0xfffffb0e | |
| 1167 | #define RTCISR WORD_REF(RTCISR_ADDR) | |
| 1168 | ||
| 1169 | #define RTCISR_SW 0x0001 /* Stopwatch timed out */ | |
| 1170 | #define RTCISR_MIN 0x0002 /* 1-minute interrupt has occurred */ | |
| 1171 | #define RTCISR_ALM 0x0004 /* Alarm interrupt has occurred */ | |
| 1172 | #define RTCISR_DAY 0x0008 /* 24-hour rollover interrupt has occurred */ | |
| 1173 | #define RTCISR_1HZ 0x0010 /* 1Hz interrupt has occurred */ | |
| 1174 | #define RTCISR_HR 0x0020 /* 1-hour interrupt has occurred */ | |
| 1175 | #define RTCISR_SAM0 0x0100 /* 4Hz / 4.6875Hz interrupt has occurred */ | |
| 1176 | #define RTCISR_SAM1 0x0200 /* 8Hz / 9.3750Hz interrupt has occurred */ | |
| 1177 | #define RTCISR_SAM2 0x0400 /* 16Hz / 18.7500Hz interrupt has occurred */ | |
| 1178 | #define RTCISR_SAM3 0x0800 /* 32Hz / 37.5000Hz interrupt has occurred */ | |
| 1179 | #define RTCISR_SAM4 0x1000 /* 64Hz / 75.0000Hz interrupt has occurred */ | |
| 1180 | #define RTCISR_SAM5 0x2000 /* 128Hz / 150.0000Hz interrupt has occurred */ | |
| 1181 | #define RTCISR_SAM6 0x4000 /* 256Hz / 300.0000Hz interrupt has occurred */ | |
| 1182 | #define RTCISR_SAM7 0x8000 /* 512Hz / 600.0000Hz interrupt has occurred */ | |
| 1183 | ||
| 1184 | /* | |
| 1185 | * RTC Interrupt Enable Register | |
| 1186 | */ | |
| 1187 | #define RTCIENR_ADDR 0xfffffb10 | |
| 1188 | #define RTCIENR WORD_REF(RTCIENR_ADDR) | |
| 1189 | ||
| 1190 | #define RTCIENR_SW 0x0001 /* Stopwatch interrupt enable */ | |
| 1191 | #define RTCIENR_MIN 0x0002 /* 1-minute interrupt enable */ | |
| 1192 | #define RTCIENR_ALM 0x0004 /* Alarm interrupt enable */ | |
| 1193 | #define RTCIENR_DAY 0x0008 /* 24-hour rollover interrupt enable */ | |
| 1194 | #define RTCIENR_1HZ 0x0010 /* 1Hz interrupt enable */ | |
| 1195 | #define RTCIENR_HR 0x0020 /* 1-hour interrupt enable */ | |
| 1196 | #define RTCIENR_SAM0 0x0100 /* 4Hz / 4.6875Hz interrupt enable */ | |
| 1197 | #define RTCIENR_SAM1 0x0200 /* 8Hz / 9.3750Hz interrupt enable */ | |
| 1198 | #define RTCIENR_SAM2 0x0400 /* 16Hz / 18.7500Hz interrupt enable */ | |
| 1199 | #define RTCIENR_SAM3 0x0800 /* 32Hz / 37.5000Hz interrupt enable */ | |
| 1200 | #define RTCIENR_SAM4 0x1000 /* 64Hz / 75.0000Hz interrupt enable */ | |
| 1201 | #define RTCIENR_SAM5 0x2000 /* 128Hz / 150.0000Hz interrupt enable */ | |
| 1202 | #define RTCIENR_SAM6 0x4000 /* 256Hz / 300.0000Hz interrupt enable */ | |
| 1203 | #define RTCIENR_SAM7 0x8000 /* 512Hz / 600.0000Hz interrupt enable */ | |
| 1204 | ||
| 1205 | /* | |
| 1206 | * Stopwatch Minutes Register | |
| 1207 | */ | |
| 1208 | #define STPWCH_ADDR 0xfffffb12 | |
| 1209 | #define STPWCH WORD_REF(STPWCH_ADDR) | |
| 1210 | ||
| 1211 | #define STPWCH_CNT_MASK 0x003f /* Stopwatch countdown value */ | |
| 1212 | #define SPTWCH_CNT_SHIFT 0 | |
| 1213 | ||
| 1214 | /* | |
| 1215 | * RTC Day Count Register | |
| 1216 | */ | |
| 1217 | #define DAYR_ADDR 0xfffffb1a | |
| 1218 | #define DAYR WORD_REF(DAYR_ADDR) | |
| 1219 | ||
| 1220 | #define DAYR_DAYS_MASK 0x1ff /* Day Setting */ | |
| 1221 | #define DAYR_DAYS_SHIFT 0 | |
| 1222 | ||
| 1223 | /* | |
| 1224 | * RTC Day Alarm Register | |
| 1225 | */ | |
| 1226 | #define DAYALARM_ADDR 0xfffffb1c | |
| 1227 | #define DAYALARM WORD_REF(DAYALARM_ADDR) | |
| 1228 | ||
| 1229 | #define DAYALARM_DAYSAL_MASK 0x01ff /* Day Setting of the Alarm */ | |
| 1230 | #define DAYALARM_DAYSAL_SHIFT 0 | |
| 1231 | ||
| 1232 | /********** | |
| 1233 | * | |
| 1234 | * 0xFFFFFCxx -- DRAM Controller | |
| 1235 | * | |
| 1236 | **********/ | |
| 1237 | ||
| 1238 | /* | |
| 1239 | * DRAM Memory Configuration Register | |
| 1240 | */ | |
| 1241 | #define DRAMMC_ADDR 0xfffffc00 | |
| 1242 | #define DRAMMC WORD_REF(DRAMMC_ADDR) | |
| 1243 | ||
| 1244 | #define DRAMMC_ROW12_MASK 0xc000 /* Row address bit for MD12 */ | |
| 1245 | #define DRAMMC_ROW12_PA10 0x0000 | |
| 1246 | #define DRAMMC_ROW12_PA21 0x4000 | |
| 1247 | #define DRAMMC_ROW12_PA23 0x8000 | |
| 1248 | #define DRAMMC_ROW0_MASK 0x3000 /* Row address bit for MD0 */ | |
| 1249 | #define DRAMMC_ROW0_PA11 0x0000 | |
| 1250 | #define DRAMMC_ROW0_PA22 0x1000 | |
| 1251 | #define DRAMMC_ROW0_PA23 0x2000 | |
| 1252 | #define DRAMMC_ROW11 0x0800 /* Row address bit for MD11 PA20/PA22 */ | |
| 1253 | #define DRAMMC_ROW10 0x0400 /* Row address bit for MD10 PA19/PA21 */ | |
| 1254 | #define DRAMMC_ROW9 0x0200 /* Row address bit for MD9 PA9/PA19 */ | |
| 1255 | #define DRAMMC_ROW8 0x0100 /* Row address bit for MD8 PA10/PA20 */ | |
| 1256 | #define DRAMMC_COL10 0x0080 /* Col address bit for MD10 PA11/PA0 */ | |
| 1257 | #define DRAMMC_COL9 0x0040 /* Col address bit for MD9 PA10/PA0 */ | |
| 1258 | #define DRAMMC_COL8 0x0020 /* Col address bit for MD8 PA9/PA0 */ | |
| 1259 | #define DRAMMC_REF_MASK 0x001f /* Reresh Cycle */ | |
| 1260 | #define DRAMMC_REF_SHIFT 0 | |
| 1261 | ||
| 1262 | /* | |
| 1263 | * DRAM Control Register | |
| 1264 | */ | |
| 1265 | #define DRAMC_ADDR 0xfffffc02 | |
| 1266 | #define DRAMC WORD_REF(DRAMC_ADDR) | |
| 1267 | ||
| 1268 | #define DRAMC_DWE 0x0001 /* DRAM Write Enable */ | |
| 1269 | #define DRAMC_RST 0x0002 /* Reset Burst Refresh Enable */ | |
| 1270 | #define DRAMC_LPR 0x0004 /* Low-Power Refresh Enable */ | |
| 1271 | #define DRAMC_SLW 0x0008 /* Slow RAM */ | |
| 1272 | #define DRAMC_LSP 0x0010 /* Light Sleep */ | |
| 1273 | #define DRAMC_MSW 0x0020 /* Slow Multiplexing */ | |
| 1274 | #define DRAMC_WS_MASK 0x00c0 /* Wait-states */ | |
| 1275 | #define DRAMC_WS_SHIFT 6 | |
| 1276 | #define DRAMC_PGSZ_MASK 0x0300 /* Page Size for fast page mode */ | |
| 1277 | #define DRAMC_PGSZ_SHIFT 8 | |
| 1278 | #define DRAMC_PGSZ_256K 0x0000 | |
| 1279 | #define DRAMC_PGSZ_512K 0x0100 | |
| 1280 | #define DRAMC_PGSZ_1024K 0x0200 | |
| 1281 | #define DRAMC_PGSZ_2048K 0x0300 | |
| 1282 | #define DRAMC_EDO 0x0400 /* EDO DRAM */ | |
| 1283 | #define DRAMC_CLK 0x0800 /* Refresh Timer Clock source select */ | |
| 1284 | #define DRAMC_BC_MASK 0x3000 /* Page Access Clock Cycle (FP mode) */ | |
| 1285 | #define DRAMC_BC_SHIFT 12 | |
| 1286 | #define DRAMC_RM 0x4000 /* Refresh Mode */ | |
| 1287 | #define DRAMC_EN 0x8000 /* DRAM Controller enable */ | |
| 1288 | ||
| 1289 | ||
| 1290 | /********** | |
| 1291 | * | |
| 1292 | * 0xFFFFFDxx -- In-Circuit Emulation (ICE) | |
| 1293 | * | |
| 1294 | **********/ | |
| 1295 | ||
| 1296 | /* | |
| 1297 | * ICE Module Address Compare Register | |
| 1298 | */ | |
| 1299 | #define ICEMACR_ADDR 0xfffffd00 | |
| 1300 | #define ICEMACR LONG_REF(ICEMACR_ADDR) | |
| 1301 | ||
| 1302 | /* | |
| 1303 | * ICE Module Address Mask Register | |
| 1304 | */ | |
| 1305 | #define ICEMAMR_ADDR 0xfffffd04 | |
| 1306 | #define ICEMAMR LONG_REF(ICEMAMR_ADDR) | |
| 1307 | ||
| 1308 | /* | |
| 1309 | * ICE Module Control Compare Register | |
| 1310 | */ | |
| 1311 | #define ICEMCCR_ADDR 0xfffffd08 | |
| 1312 | #define ICEMCCR WORD_REF(ICEMCCR_ADDR) | |
| 1313 | ||
| 1314 | #define ICEMCCR_PD 0x0001 /* Program/Data Cycle Selection */ | |
| 1315 | #define ICEMCCR_RW 0x0002 /* Read/Write Cycle Selection */ | |
| 1316 | ||
| 1317 | /* | |
| 1318 | * ICE Module Control Mask Register | |
| 1319 | */ | |
| 1320 | #define ICEMCMR_ADDR 0xfffffd0a | |
| 1321 | #define ICEMCMR WORD_REF(ICEMCMR_ADDR) | |
| 1322 | ||
| 1323 | #define ICEMCMR_PDM 0x0001 /* Program/Data Cycle Mask */ | |
| 1324 | #define ICEMCMR_RWM 0x0002 /* Read/Write Cycle Mask */ | |
| 1325 | ||
| 1326 | /* | |
| 1327 | * ICE Module Control Register | |
| 1328 | */ | |
| 1329 | #define ICEMCR_ADDR 0xfffffd0c | |
| 1330 | #define ICEMCR WORD_REF(ICEMCR_ADDR) | |
| 1331 | ||
| 1332 | #define ICEMCR_CEN 0x0001 /* Compare Enable */ | |
| 1333 | #define ICEMCR_PBEN 0x0002 /* Program Break Enable */ | |
| 1334 | #define ICEMCR_SB 0x0004 /* Single Breakpoint */ | |
| 1335 | #define ICEMCR_HMDIS 0x0008 /* HardMap disable */ | |
| 1336 | #define ICEMCR_BBIEN 0x0010 /* Bus Break Interrupt Enable */ | |
| 1337 | ||
| 1338 | /* | |
| 1339 | * ICE Module Status Register | |
| 1340 | */ | |
| 1341 | #define ICEMSR_ADDR 0xfffffd0e | |
| 1342 | #define ICEMSR WORD_REF(ICEMSR_ADDR) | |
| 1343 | ||
| 1344 | #define ICEMSR_EMUEN 0x0001 /* Emulation Enable */ | |
| 1345 | #define ICEMSR_BRKIRQ 0x0002 /* A-Line Vector Fetch Detected */ | |
| 1346 | #define ICEMSR_BBIRQ 0x0004 /* Bus Break Interrupt Detected */ | |
| 1347 | #define ICEMSR_EMIRQ 0x0008 /* EMUIRQ Falling Edge Detected */ | |
| 1348 | ||
| 1349 | #endif /* _MC68VZ328_H_ */ |