Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * Digi AccelePort USB-4 and USB-2 Serial Converters | |
3 | * | |
4 | * Copyright 2000 by Digi International | |
5 | * | |
6 | * This program is free software; you can redistribute it and/or modify | |
7 | * it under the terms of the GNU General Public License as published by | |
8 | * the Free Software Foundation; either version 2 of the License, or | |
9 | * (at your option) any later version. | |
10 | * | |
11 | * Shamelessly based on Brian Warner's keyspan_pda.c and Greg Kroah-Hartman's | |
12 | * usb-serial driver. | |
13 | * | |
14 | * Peter Berger (pberger@brimson.com) | |
15 | * Al Borchers (borchers@steinerpoint.com) | |
16 | * | |
17 | * (12/03/2001) gkh | |
95da310e | 18 | * switched to using port->port.count instead of private version. |
1da177e4 LT |
19 | * Removed port->active |
20 | * | |
21 | * (04/08/2001) gb | |
22 | * Identify version on module load. | |
23 | * | |
24 | * (11/01/2000) Adam J. Richter | |
25 | * usb_device_id table support | |
26 | * | |
27 | * (11/01/2000) pberger and borchers | |
28 | * -- Turned off the USB_DISABLE_SPD flag for write bulk urbs--it caused | |
29 | * USB 4 ports to hang on startup. | |
30 | * -- Serialized access to write urbs by adding the dp_write_urb_in_use | |
31 | * flag; otherwise, the driver caused SMP system hangs. Watching the | |
32 | * urb status is not sufficient. | |
33 | * | |
34 | * (10/05/2000) gkh | |
35 | * -- Fixed bug with urb->dev not being set properly, now that the usb | |
36 | * core needs it. | |
37 | * | |
38 | * (8/8/2000) pberger and borchers | |
39 | * -- Fixed close so that | |
40 | * - it can timeout while waiting for transmit idle, if needed; | |
41 | * - it ignores interrupts when flushing the port, turning | |
42 | * of modem signalling, and so on; | |
43 | * - it waits for the flush to really complete before returning. | |
44 | * -- Read_bulk_callback and write_bulk_callback check for a closed | |
45 | * port before using the tty struct or writing to the port. | |
46 | * -- The two changes above fix the oops caused by interrupted closes. | |
47 | * -- Added interruptible args to write_oob_command and set_modem_signals | |
48 | * and added a timeout arg to transmit_idle; needed for fixes to | |
49 | * close. | |
50 | * -- Added code for rx_throttle and rx_unthrottle so that input flow | |
51 | * control works. | |
52 | * -- Added code to set overrun, parity, framing, and break errors | |
53 | * (untested). | |
54 | * -- Set USB_DISABLE_SPD flag for write bulk urbs, so no 0 length | |
55 | * bulk writes are done. These hung the Digi USB device. The | |
56 | * 0 length bulk writes were a new feature of usb-uhci added in | |
57 | * the 2.4.0-test6 kernels. | |
58 | * -- Fixed mod inc race in open; do mod inc before sleeping to wait | |
59 | * for a close to finish. | |
60 | * | |
61 | * (7/31/2000) pberger | |
62 | * -- Fixed bugs with hardware handshaking: | |
63 | * - Added code to set/clear tty->hw_stopped in digi_read_oob_callback() | |
64 | * and digi_set_termios() | |
65 | * -- Added code in digi_set_termios() to | |
66 | * - add conditional in code handling transition from B0 to only | |
67 | * set RTS if RTS/CTS flow control is either not in use or if | |
68 | * the port is not currently throttled. | |
69 | * - handle turning off CRTSCTS. | |
70 | * | |
71 | * (7/30/2000) borchers | |
72 | * -- Added support for more than one Digi USB device by moving | |
73 | * globals to a private structure in the pointed to from the | |
74 | * usb_serial structure. | |
75 | * -- Moved the modem change and transmit idle wait queues into | |
76 | * the port private structure, so each port has its own queue | |
77 | * rather than sharing global queues. | |
78 | * -- Added support for break signals. | |
79 | * | |
80 | * (7/25/2000) pberger | |
81 | * -- Added USB-2 support. Note: the USB-2 supports 3 devices: two | |
82 | * serial and a parallel port. The parallel port is implemented | |
83 | * as a serial-to-parallel converter. That is, the driver actually | |
84 | * presents all three USB-2 interfaces as serial ports, but the third | |
85 | * one physically connects to a parallel device. Thus, for example, | |
86 | * one could plug a parallel printer into the USB-2's third port, | |
87 | * but from the kernel's (and userland's) point of view what's | |
88 | * actually out there is a serial device. | |
89 | * | |
90 | * (7/15/2000) borchers | |
91 | * -- Fixed race in open when a close is in progress. | |
92 | * -- Keep count of opens and dec the module use count for each | |
93 | * outstanding open when shutdown is called (on disconnect). | |
94 | * -- Fixed sanity checks in read_bulk_callback and write_bulk_callback | |
95 | * so pointers are checked before use. | |
96 | * -- Split read bulk callback into in band and out of band | |
97 | * callbacks, and no longer restart read chains if there is | |
98 | * a status error or a sanity error. This fixed the seg | |
99 | * faults and other errors we used to get on disconnect. | |
100 | * -- Port->active is once again a flag as usb-serial intended it | |
101 | * to be, not a count. Since it was only a char it would | |
102 | * have been limited to 256 simultaneous opens. Now the open | |
103 | * count is kept in the port private structure in dp_open_count. | |
104 | * -- Added code for modularization of the digi_acceleport driver. | |
105 | * | |
106 | * (6/27/2000) pberger and borchers | |
107 | * -- Zeroed out sync field in the wakeup_task before first use; | |
108 | * otherwise the uninitialized value might prevent the task from | |
109 | * being scheduled. | |
110 | * -- Initialized ret value to 0 in write_bulk_callback, otherwise | |
111 | * the uninitialized value could cause a spurious debugging message. | |
112 | * | |
113 | * (6/22/2000) pberger and borchers | |
114 | * -- Made cond_wait_... inline--apparently on SPARC the flags arg | |
115 | * to spin_lock_irqsave cannot be passed to another function | |
116 | * to call spin_unlock_irqrestore. Thanks to Pauline Middelink. | |
117 | * -- In digi_set_modem_signals the inner nested spin locks use just | |
118 | * spin_lock() rather than spin_lock_irqsave(). The old code | |
119 | * mistakenly left interrupts off. Thanks to Pauline Middelink. | |
120 | * -- copy_from_user (which can sleep) is no longer called while a | |
121 | * spinlock is held. We copy to a local buffer before getting | |
122 | * the spinlock--don't like the extra copy but the code is simpler. | |
123 | * -- Printk and dbg are no longer called while a spin lock is held. | |
124 | * | |
125 | * (6/4/2000) pberger and borchers | |
126 | * -- Replaced separate calls to spin_unlock_irqrestore and | |
127 | * interruptible_sleep_on_timeout with a new function | |
128 | * cond_wait_interruptible_timeout_irqrestore. This eliminates | |
129 | * the race condition where the wake up could happen after | |
130 | * the unlock and before the sleep. | |
131 | * -- Close now waits for output to drain. | |
132 | * -- Open waits until any close in progress is finished. | |
133 | * -- All out of band responses are now processed, not just the | |
134 | * first in a USB packet. | |
135 | * -- Fixed a bug that prevented the driver from working when the | |
136 | * first Digi port was not the first USB serial port--the driver | |
137 | * was mistakenly using the external USB serial port number to | |
138 | * try to index into its internal ports. | |
139 | * -- Fixed an SMP bug -- write_bulk_callback is called directly from | |
140 | * an interrupt, so spin_lock_irqsave/spin_unlock_irqrestore are | |
141 | * needed for locks outside write_bulk_callback that are also | |
142 | * acquired by write_bulk_callback to prevent deadlocks. | |
143 | * -- Fixed support for select() by making digi_chars_in_buffer() | |
144 | * return 256 when -EINPROGRESS is set, as the line discipline | |
145 | * code in n_tty.c expects. | |
146 | * -- Fixed an include file ordering problem that prevented debugging | |
147 | * messages from working. | |
148 | * -- Fixed an intermittent timeout problem that caused writes to | |
149 | * sometimes get stuck on some machines on some kernels. It turns | |
150 | * out in these circumstances write_chan() (in n_tty.c) was | |
151 | * asleep waiting for our wakeup call. Even though we call | |
152 | * wake_up_interruptible() in digi_write_bulk_callback(), there is | |
153 | * a race condition that could cause the wakeup to fail: if our | |
154 | * wake_up_interruptible() call occurs between the time that our | |
155 | * driver write routine finishes and write_chan() sets current->state | |
156 | * to TASK_INTERRUPTIBLE, the effect of our wakeup setting the state | |
157 | * to TASK_RUNNING will be lost and write_chan's subsequent call to | |
158 | * schedule() will never return (unless it catches a signal). | |
159 | * This race condition occurs because write_bulk_callback() (and thus | |
0779bf2d | 160 | * the wakeup) are called asynchronously from an interrupt, rather than |
1da177e4 LT |
161 | * from the scheduler. We can avoid the race by calling the wakeup |
162 | * from the scheduler queue and that's our fix: Now, at the end of | |
163 | * write_bulk_callback() we queue up a wakeup call on the scheduler | |
164 | * task queue. We still also invoke the wakeup directly since that | |
165 | * squeezes a bit more performance out of the driver, and any lost | |
166 | * race conditions will get cleaned up at the next scheduler run. | |
167 | * | |
168 | * NOTE: The problem also goes away if you comment out | |
169 | * the two code lines in write_chan() where current->state | |
170 | * is set to TASK_RUNNING just before calling driver.write() and to | |
171 | * TASK_INTERRUPTIBLE immediately afterwards. This is why the | |
172 | * problem did not show up with the 2.2 kernels -- they do not | |
173 | * include that code. | |
174 | * | |
175 | * (5/16/2000) pberger and borchers | |
176 | * -- Added timeouts to sleeps, to defend against lost wake ups. | |
177 | * -- Handle transition to/from B0 baud rate in digi_set_termios. | |
178 | * | |
179 | * (5/13/2000) pberger and borchers | |
180 | * -- All commands now sent on out of band port, using | |
181 | * digi_write_oob_command. | |
182 | * -- Get modem control signals whenever they change, support TIOCMGET/ | |
183 | * SET/BIS/BIC ioctls. | |
184 | * -- digi_set_termios now supports parity, word size, stop bits, and | |
185 | * receive enable. | |
186 | * -- Cleaned up open and close, use digi_set_termios and | |
187 | * digi_write_oob_command to set port parameters. | |
188 | * -- Added digi_startup_device to start read chains on all ports. | |
189 | * -- Write buffer is only used when count==1, to be sure put_char can | |
190 | * write a char (unless the buffer is full). | |
191 | * | |
192 | * (5/10/2000) pberger and borchers | |
193 | * -- Added MOD_INC_USE_COUNT/MOD_DEC_USE_COUNT calls on open/close. | |
194 | * -- Fixed problem where the first incoming character is lost on | |
195 | * port opens after the first close on that port. Now we keep | |
196 | * the read_urb chain open until shutdown. | |
197 | * -- Added more port conditioning calls in digi_open and digi_close. | |
198 | * -- Convert port->active to a use count so that we can deal with multiple | |
199 | * opens and closes properly. | |
200 | * -- Fixed some problems with the locking code. | |
201 | * | |
202 | * (5/3/2000) pberger and borchers | |
203 | * -- First alpha version of the driver--many known limitations and bugs. | |
204 | * | |
205 | * | |
206 | * Locking and SMP | |
207 | * | |
208 | * - Each port, including the out-of-band port, has a lock used to | |
209 | * serialize all access to the port's private structure. | |
210 | * - The port lock is also used to serialize all writes and access to | |
211 | * the port's URB. | |
212 | * - The port lock is also used for the port write_wait condition | |
213 | * variable. Holding the port lock will prevent a wake up on the | |
214 | * port's write_wait; this can be used with cond_wait_... to be sure | |
215 | * the wake up is not lost in a race when dropping the lock and | |
216 | * sleeping waiting for the wakeup. | |
217 | * - digi_write() does not sleep, since it is sometimes called on | |
218 | * interrupt time. | |
219 | * - digi_write_bulk_callback() and digi_read_bulk_callback() are | |
220 | * called directly from interrupts. Hence spin_lock_irqsave() | |
221 | * and spin_unlock_irqrestore() are used in the rest of the code | |
222 | * for any locks they acquire. | |
223 | * - digi_write_bulk_callback() gets the port lock before waking up | |
224 | * processes sleeping on the port write_wait. It also schedules | |
225 | * wake ups so they happen from the scheduler, because the tty | |
226 | * system can miss wake ups from interrupts. | |
227 | * - All sleeps use a timeout of DIGI_RETRY_TIMEOUT before looping to | |
228 | * recheck the condition they are sleeping on. This is defensive, | |
229 | * in case a wake up is lost. | |
230 | * - Following Documentation/DocBook/kernel-locking.pdf no spin locks | |
231 | * are held when calling copy_to/from_user or printk. | |
1da177e4 LT |
232 | */ |
233 | ||
1da177e4 LT |
234 | #include <linux/kernel.h> |
235 | #include <linux/errno.h> | |
236 | #include <linux/init.h> | |
237 | #include <linux/slab.h> | |
238 | #include <linux/tty.h> | |
239 | #include <linux/tty_driver.h> | |
240 | #include <linux/tty_flip.h> | |
241 | #include <linux/module.h> | |
242 | #include <linux/spinlock.h> | |
243 | #include <linux/workqueue.h> | |
41ad427d | 244 | #include <linux/uaccess.h> |
1da177e4 LT |
245 | #include <linux/usb.h> |
246 | #include <linux/wait.h> | |
a969888c | 247 | #include <linux/usb/serial.h> |
1da177e4 LT |
248 | |
249 | /* Defines */ | |
250 | ||
251 | /* | |
252 | * Version Information | |
253 | */ | |
254 | #define DRIVER_VERSION "v1.80.1.2" | |
255 | #define DRIVER_AUTHOR "Peter Berger <pberger@brimson.com>, Al Borchers <borchers@steinerpoint.com>" | |
256 | #define DRIVER_DESC "Digi AccelePort USB-2/USB-4 Serial Converter driver" | |
257 | ||
258 | /* port output buffer length -- must be <= transfer buffer length - 2 */ | |
259 | /* so we can be sure to send the full buffer in one urb */ | |
260 | #define DIGI_OUT_BUF_SIZE 8 | |
261 | ||
262 | /* port input buffer length -- must be >= transfer buffer length - 3 */ | |
263 | /* so we can be sure to hold at least one full buffer from one urb */ | |
264 | #define DIGI_IN_BUF_SIZE 64 | |
265 | ||
266 | /* retry timeout while sleeping */ | |
267 | #define DIGI_RETRY_TIMEOUT (HZ/10) | |
268 | ||
269 | /* timeout while waiting for tty output to drain in close */ | |
270 | /* this delay is used twice in close, so the total delay could */ | |
271 | /* be twice this value */ | |
272 | #define DIGI_CLOSE_TIMEOUT (5*HZ) | |
273 | ||
274 | ||
275 | /* AccelePort USB Defines */ | |
276 | ||
277 | /* ids */ | |
278 | #define DIGI_VENDOR_ID 0x05c5 | |
279 | #define DIGI_2_ID 0x0002 /* USB-2 */ | |
280 | #define DIGI_4_ID 0x0004 /* USB-4 */ | |
281 | ||
282 | /* commands | |
283 | * "INB": can be used on the in-band endpoint | |
284 | * "OOB": can be used on the out-of-band endpoint | |
285 | */ | |
286 | #define DIGI_CMD_SET_BAUD_RATE 0 /* INB, OOB */ | |
287 | #define DIGI_CMD_SET_WORD_SIZE 1 /* INB, OOB */ | |
288 | #define DIGI_CMD_SET_PARITY 2 /* INB, OOB */ | |
289 | #define DIGI_CMD_SET_STOP_BITS 3 /* INB, OOB */ | |
290 | #define DIGI_CMD_SET_INPUT_FLOW_CONTROL 4 /* INB, OOB */ | |
291 | #define DIGI_CMD_SET_OUTPUT_FLOW_CONTROL 5 /* INB, OOB */ | |
292 | #define DIGI_CMD_SET_DTR_SIGNAL 6 /* INB, OOB */ | |
293 | #define DIGI_CMD_SET_RTS_SIGNAL 7 /* INB, OOB */ | |
294 | #define DIGI_CMD_READ_INPUT_SIGNALS 8 /* OOB */ | |
295 | #define DIGI_CMD_IFLUSH_FIFO 9 /* OOB */ | |
296 | #define DIGI_CMD_RECEIVE_ENABLE 10 /* INB, OOB */ | |
297 | #define DIGI_CMD_BREAK_CONTROL 11 /* INB, OOB */ | |
298 | #define DIGI_CMD_LOCAL_LOOPBACK 12 /* INB, OOB */ | |
299 | #define DIGI_CMD_TRANSMIT_IDLE 13 /* INB, OOB */ | |
300 | #define DIGI_CMD_READ_UART_REGISTER 14 /* OOB */ | |
301 | #define DIGI_CMD_WRITE_UART_REGISTER 15 /* INB, OOB */ | |
302 | #define DIGI_CMD_AND_UART_REGISTER 16 /* INB, OOB */ | |
303 | #define DIGI_CMD_OR_UART_REGISTER 17 /* INB, OOB */ | |
304 | #define DIGI_CMD_SEND_DATA 18 /* INB */ | |
305 | #define DIGI_CMD_RECEIVE_DATA 19 /* INB */ | |
306 | #define DIGI_CMD_RECEIVE_DISABLE 20 /* INB */ | |
307 | #define DIGI_CMD_GET_PORT_TYPE 21 /* OOB */ | |
308 | ||
309 | /* baud rates */ | |
310 | #define DIGI_BAUD_50 0 | |
311 | #define DIGI_BAUD_75 1 | |
312 | #define DIGI_BAUD_110 2 | |
313 | #define DIGI_BAUD_150 3 | |
314 | #define DIGI_BAUD_200 4 | |
315 | #define DIGI_BAUD_300 5 | |
316 | #define DIGI_BAUD_600 6 | |
317 | #define DIGI_BAUD_1200 7 | |
318 | #define DIGI_BAUD_1800 8 | |
319 | #define DIGI_BAUD_2400 9 | |
320 | #define DIGI_BAUD_4800 10 | |
321 | #define DIGI_BAUD_7200 11 | |
322 | #define DIGI_BAUD_9600 12 | |
323 | #define DIGI_BAUD_14400 13 | |
324 | #define DIGI_BAUD_19200 14 | |
325 | #define DIGI_BAUD_28800 15 | |
326 | #define DIGI_BAUD_38400 16 | |
327 | #define DIGI_BAUD_57600 17 | |
328 | #define DIGI_BAUD_76800 18 | |
329 | #define DIGI_BAUD_115200 19 | |
330 | #define DIGI_BAUD_153600 20 | |
331 | #define DIGI_BAUD_230400 21 | |
332 | #define DIGI_BAUD_460800 22 | |
333 | ||
334 | /* arguments */ | |
335 | #define DIGI_WORD_SIZE_5 0 | |
336 | #define DIGI_WORD_SIZE_6 1 | |
337 | #define DIGI_WORD_SIZE_7 2 | |
338 | #define DIGI_WORD_SIZE_8 3 | |
339 | ||
340 | #define DIGI_PARITY_NONE 0 | |
341 | #define DIGI_PARITY_ODD 1 | |
342 | #define DIGI_PARITY_EVEN 2 | |
343 | #define DIGI_PARITY_MARK 3 | |
344 | #define DIGI_PARITY_SPACE 4 | |
345 | ||
346 | #define DIGI_STOP_BITS_1 0 | |
347 | #define DIGI_STOP_BITS_2 1 | |
348 | ||
349 | #define DIGI_INPUT_FLOW_CONTROL_XON_XOFF 1 | |
350 | #define DIGI_INPUT_FLOW_CONTROL_RTS 2 | |
351 | #define DIGI_INPUT_FLOW_CONTROL_DTR 4 | |
352 | ||
353 | #define DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF 1 | |
354 | #define DIGI_OUTPUT_FLOW_CONTROL_CTS 2 | |
355 | #define DIGI_OUTPUT_FLOW_CONTROL_DSR 4 | |
356 | ||
357 | #define DIGI_DTR_INACTIVE 0 | |
358 | #define DIGI_DTR_ACTIVE 1 | |
359 | #define DIGI_DTR_INPUT_FLOW_CONTROL 2 | |
360 | ||
361 | #define DIGI_RTS_INACTIVE 0 | |
362 | #define DIGI_RTS_ACTIVE 1 | |
363 | #define DIGI_RTS_INPUT_FLOW_CONTROL 2 | |
364 | #define DIGI_RTS_TOGGLE 3 | |
365 | ||
366 | #define DIGI_FLUSH_TX 1 | |
367 | #define DIGI_FLUSH_RX 2 | |
368 | #define DIGI_RESUME_TX 4 /* clears xoff condition */ | |
369 | ||
370 | #define DIGI_TRANSMIT_NOT_IDLE 0 | |
371 | #define DIGI_TRANSMIT_IDLE 1 | |
372 | ||
373 | #define DIGI_DISABLE 0 | |
374 | #define DIGI_ENABLE 1 | |
375 | ||
376 | #define DIGI_DEASSERT 0 | |
377 | #define DIGI_ASSERT 1 | |
378 | ||
379 | /* in band status codes */ | |
380 | #define DIGI_OVERRUN_ERROR 4 | |
381 | #define DIGI_PARITY_ERROR 8 | |
382 | #define DIGI_FRAMING_ERROR 16 | |
383 | #define DIGI_BREAK_ERROR 32 | |
384 | ||
385 | /* out of band status */ | |
386 | #define DIGI_NO_ERROR 0 | |
387 | #define DIGI_BAD_FIRST_PARAMETER 1 | |
388 | #define DIGI_BAD_SECOND_PARAMETER 2 | |
389 | #define DIGI_INVALID_LINE 3 | |
390 | #define DIGI_INVALID_OPCODE 4 | |
391 | ||
392 | /* input signals */ | |
393 | #define DIGI_READ_INPUT_SIGNALS_SLOT 1 | |
394 | #define DIGI_READ_INPUT_SIGNALS_ERR 2 | |
395 | #define DIGI_READ_INPUT_SIGNALS_BUSY 4 | |
396 | #define DIGI_READ_INPUT_SIGNALS_PE 8 | |
397 | #define DIGI_READ_INPUT_SIGNALS_CTS 16 | |
398 | #define DIGI_READ_INPUT_SIGNALS_DSR 32 | |
399 | #define DIGI_READ_INPUT_SIGNALS_RI 64 | |
400 | #define DIGI_READ_INPUT_SIGNALS_DCD 128 | |
401 | ||
402 | ||
403 | /* Structures */ | |
404 | ||
405 | struct digi_serial { | |
406 | spinlock_t ds_serial_lock; | |
407 | struct usb_serial_port *ds_oob_port; /* out-of-band port */ | |
408 | int ds_oob_port_num; /* index of out-of-band port */ | |
409 | int ds_device_started; | |
410 | }; | |
411 | ||
412 | struct digi_port { | |
413 | spinlock_t dp_port_lock; | |
414 | int dp_port_num; | |
415 | int dp_out_buf_len; | |
416 | unsigned char dp_out_buf[DIGI_OUT_BUF_SIZE]; | |
1da177e4 LT |
417 | int dp_write_urb_in_use; |
418 | unsigned int dp_modem_signals; | |
419 | wait_queue_head_t dp_modem_change_wait; | |
420 | int dp_transmit_idle; | |
421 | wait_queue_head_t dp_transmit_idle_wait; | |
422 | int dp_throttled; | |
423 | int dp_throttle_restart; | |
424 | wait_queue_head_t dp_flush_wait; | |
1da177e4 LT |
425 | wait_queue_head_t dp_close_wait; /* wait queue for close */ |
426 | struct work_struct dp_wakeup_work; | |
c4028958 | 427 | struct usb_serial_port *dp_port; |
1da177e4 LT |
428 | }; |
429 | ||
430 | ||
431 | /* Local Function Declarations */ | |
432 | ||
c6d61269 | 433 | static void digi_wakeup_write(struct usb_serial_port *port); |
c4028958 | 434 | static void digi_wakeup_write_lock(struct work_struct *work); |
c6d61269 AC |
435 | static int digi_write_oob_command(struct usb_serial_port *port, |
436 | unsigned char *buf, int count, int interruptible); | |
437 | static int digi_write_inb_command(struct usb_serial_port *port, | |
438 | unsigned char *buf, int count, unsigned long timeout); | |
439 | static int digi_set_modem_signals(struct usb_serial_port *port, | |
440 | unsigned int modem_signals, int interruptible); | |
441 | static int digi_transmit_idle(struct usb_serial_port *port, | |
442 | unsigned long timeout); | |
41ad427d AC |
443 | static void digi_rx_throttle(struct tty_struct *tty); |
444 | static void digi_rx_unthrottle(struct tty_struct *tty); | |
95da310e AC |
445 | static void digi_set_termios(struct tty_struct *tty, |
446 | struct usb_serial_port *port, struct ktermios *old_termios); | |
447 | static void digi_break_ctl(struct tty_struct *tty, int break_state); | |
448 | static int digi_tiocmget(struct tty_struct *tty, struct file *file); | |
449 | static int digi_tiocmset(struct tty_struct *tty, struct file *file, | |
c6d61269 | 450 | unsigned int set, unsigned int clear); |
95da310e AC |
451 | static int digi_write(struct tty_struct *tty, struct usb_serial_port *port, |
452 | const unsigned char *buf, int count); | |
c6d61269 | 453 | static void digi_write_bulk_callback(struct urb *urb); |
95da310e AC |
454 | static int digi_write_room(struct tty_struct *tty); |
455 | static int digi_chars_in_buffer(struct tty_struct *tty); | |
a509a7e4 | 456 | static int digi_open(struct tty_struct *tty, struct usb_serial_port *port); |
335f8514 AC |
457 | static void digi_close(struct usb_serial_port *port); |
458 | static int digi_carrier_raised(struct usb_serial_port *port); | |
459 | static void digi_dtr_rts(struct usb_serial_port *port, int on); | |
c6d61269 AC |
460 | static int digi_startup_device(struct usb_serial *serial); |
461 | static int digi_startup(struct usb_serial *serial); | |
f9c99bb8 AS |
462 | static void digi_disconnect(struct usb_serial *serial); |
463 | static void digi_release(struct usb_serial *serial); | |
c6d61269 AC |
464 | static void digi_read_bulk_callback(struct urb *urb); |
465 | static int digi_read_inb_callback(struct urb *urb); | |
466 | static int digi_read_oob_callback(struct urb *urb); | |
1da177e4 LT |
467 | |
468 | ||
469 | /* Statics */ | |
470 | ||
471 | static int debug; | |
472 | ||
473 | static struct usb_device_id id_table_combined [] = { | |
474 | { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, | |
475 | { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, | |
476 | { } /* Terminating entry */ | |
477 | }; | |
478 | ||
479 | static struct usb_device_id id_table_2 [] = { | |
480 | { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, | |
481 | { } /* Terminating entry */ | |
482 | }; | |
483 | ||
484 | static struct usb_device_id id_table_4 [] = { | |
485 | { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, | |
486 | { } /* Terminating entry */ | |
487 | }; | |
488 | ||
41ad427d | 489 | MODULE_DEVICE_TABLE(usb, id_table_combined); |
1da177e4 LT |
490 | |
491 | static struct usb_driver digi_driver = { | |
1da177e4 LT |
492 | .name = "digi_acceleport", |
493 | .probe = usb_serial_probe, | |
494 | .disconnect = usb_serial_disconnect, | |
495 | .id_table = id_table_combined, | |
ba9dc657 | 496 | .no_dynamic_id = 1, |
1da177e4 LT |
497 | }; |
498 | ||
499 | ||
500 | /* device info needed for the Digi serial converter */ | |
501 | ||
ea65370d | 502 | static struct usb_serial_driver digi_acceleport_2_device = { |
18fcac35 | 503 | .driver = { |
269bda1c GKH |
504 | .owner = THIS_MODULE, |
505 | .name = "digi_2", | |
18fcac35 | 506 | }, |
269bda1c | 507 | .description = "Digi 2 port USB adapter", |
d9b1b787 | 508 | .usb_driver = &digi_driver, |
1da177e4 | 509 | .id_table = id_table_2, |
1da177e4 LT |
510 | .num_ports = 3, |
511 | .open = digi_open, | |
512 | .close = digi_close, | |
335f8514 AC |
513 | .dtr_rts = digi_dtr_rts, |
514 | .carrier_raised = digi_carrier_raised, | |
1da177e4 LT |
515 | .write = digi_write, |
516 | .write_room = digi_write_room, | |
517 | .write_bulk_callback = digi_write_bulk_callback, | |
518 | .read_bulk_callback = digi_read_bulk_callback, | |
519 | .chars_in_buffer = digi_chars_in_buffer, | |
520 | .throttle = digi_rx_throttle, | |
521 | .unthrottle = digi_rx_unthrottle, | |
1da177e4 LT |
522 | .set_termios = digi_set_termios, |
523 | .break_ctl = digi_break_ctl, | |
524 | .tiocmget = digi_tiocmget, | |
525 | .tiocmset = digi_tiocmset, | |
526 | .attach = digi_startup, | |
f9c99bb8 AS |
527 | .disconnect = digi_disconnect, |
528 | .release = digi_release, | |
1da177e4 LT |
529 | }; |
530 | ||
ea65370d | 531 | static struct usb_serial_driver digi_acceleport_4_device = { |
18fcac35 | 532 | .driver = { |
269bda1c GKH |
533 | .owner = THIS_MODULE, |
534 | .name = "digi_4", | |
18fcac35 | 535 | }, |
269bda1c | 536 | .description = "Digi 4 port USB adapter", |
d9b1b787 | 537 | .usb_driver = &digi_driver, |
1da177e4 | 538 | .id_table = id_table_4, |
1da177e4 LT |
539 | .num_ports = 4, |
540 | .open = digi_open, | |
541 | .close = digi_close, | |
542 | .write = digi_write, | |
543 | .write_room = digi_write_room, | |
544 | .write_bulk_callback = digi_write_bulk_callback, | |
545 | .read_bulk_callback = digi_read_bulk_callback, | |
546 | .chars_in_buffer = digi_chars_in_buffer, | |
547 | .throttle = digi_rx_throttle, | |
548 | .unthrottle = digi_rx_unthrottle, | |
1da177e4 LT |
549 | .set_termios = digi_set_termios, |
550 | .break_ctl = digi_break_ctl, | |
551 | .tiocmget = digi_tiocmget, | |
552 | .tiocmset = digi_tiocmset, | |
553 | .attach = digi_startup, | |
f9c99bb8 AS |
554 | .disconnect = digi_disconnect, |
555 | .release = digi_release, | |
1da177e4 LT |
556 | }; |
557 | ||
558 | ||
559 | /* Functions */ | |
560 | ||
561 | /* | |
41ad427d AC |
562 | * Cond Wait Interruptible Timeout Irqrestore |
563 | * | |
564 | * Do spin_unlock_irqrestore and interruptible_sleep_on_timeout | |
565 | * so that wake ups are not lost if they occur between the unlock | |
566 | * and the sleep. In other words, spin_unlock_irqrestore and | |
567 | * interruptible_sleep_on_timeout are "atomic" with respect to | |
568 | * wake ups. This is used to implement condition variables. | |
569 | * | |
570 | * interruptible_sleep_on_timeout is deprecated and has been replaced | |
571 | * with the equivalent code. | |
572 | */ | |
1da177e4 | 573 | |
c6d61269 | 574 | static long cond_wait_interruptible_timeout_irqrestore( |
1da177e4 | 575 | wait_queue_head_t *q, long timeout, |
c6d61269 | 576 | spinlock_t *lock, unsigned long flags) |
5a33956a | 577 | __releases(lock) |
1da177e4 LT |
578 | { |
579 | DEFINE_WAIT(wait); | |
580 | ||
45f23f18 | 581 | prepare_to_wait(q, &wait, TASK_INTERRUPTIBLE); |
1da177e4 LT |
582 | spin_unlock_irqrestore(lock, flags); |
583 | timeout = schedule_timeout(timeout); | |
584 | finish_wait(q, &wait); | |
585 | ||
586 | return timeout; | |
1da177e4 LT |
587 | } |
588 | ||
589 | ||
590 | /* | |
41ad427d AC |
591 | * Digi Wakeup Write |
592 | * | |
593 | * Wake up port, line discipline, and tty processes sleeping | |
594 | * on writes. | |
595 | */ | |
1da177e4 | 596 | |
c4028958 | 597 | static void digi_wakeup_write_lock(struct work_struct *work) |
1da177e4 | 598 | { |
41ad427d AC |
599 | struct digi_port *priv = |
600 | container_of(work, struct digi_port, dp_wakeup_work); | |
c4028958 | 601 | struct usb_serial_port *port = priv->dp_port; |
1da177e4 | 602 | unsigned long flags; |
1da177e4 | 603 | |
c6d61269 AC |
604 | spin_lock_irqsave(&priv->dp_port_lock, flags); |
605 | digi_wakeup_write(port); | |
606 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); | |
1da177e4 LT |
607 | } |
608 | ||
c6d61269 | 609 | static void digi_wakeup_write(struct usb_serial_port *port) |
1da177e4 | 610 | { |
4a90f09b AC |
611 | struct tty_struct *tty = tty_port_tty_get(&port->port); |
612 | tty_wakeup(tty); | |
613 | tty_kref_put(tty); | |
1da177e4 LT |
614 | } |
615 | ||
616 | ||
617 | /* | |
41ad427d AC |
618 | * Digi Write OOB Command |
619 | * | |
620 | * Write commands on the out of band port. Commands are 4 | |
621 | * bytes each, multiple commands can be sent at once, and | |
622 | * no command will be split across USB packets. Returns 0 | |
623 | * if successful, -EINTR if interrupted while sleeping and | |
624 | * the interruptible flag is true, or a negative error | |
625 | * returned by usb_submit_urb. | |
626 | */ | |
1da177e4 | 627 | |
c6d61269 AC |
628 | static int digi_write_oob_command(struct usb_serial_port *port, |
629 | unsigned char *buf, int count, int interruptible) | |
1da177e4 LT |
630 | { |
631 | ||
632 | int ret = 0; | |
633 | int len; | |
634 | struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; | |
635 | struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); | |
636 | unsigned long flags = 0; | |
637 | ||
c6d61269 | 638 | dbg("digi_write_oob_command: TOP: port=%d, count=%d", oob_priv->dp_port_num, count); |
1da177e4 | 639 | |
c6d61269 | 640 | spin_lock_irqsave(&oob_priv->dp_port_lock, flags); |
41ad427d | 641 | while (count > 0) { |
50de36f7 | 642 | while (oob_priv->dp_write_urb_in_use) { |
1da177e4 LT |
643 | cond_wait_interruptible_timeout_irqrestore( |
644 | &oob_port->write_wait, DIGI_RETRY_TIMEOUT, | |
c6d61269 AC |
645 | &oob_priv->dp_port_lock, flags); |
646 | if (interruptible && signal_pending(current)) | |
647 | return -EINTR; | |
648 | spin_lock_irqsave(&oob_priv->dp_port_lock, flags); | |
1da177e4 LT |
649 | } |
650 | ||
651 | /* len must be a multiple of 4, so commands are not split */ | |
c6d61269 AC |
652 | len = min(count, oob_port->bulk_out_size); |
653 | if (len > 4) | |
1da177e4 | 654 | len &= ~3; |
c6d61269 | 655 | memcpy(oob_port->write_urb->transfer_buffer, buf, len); |
1da177e4 LT |
656 | oob_port->write_urb->transfer_buffer_length = len; |
657 | oob_port->write_urb->dev = port->serial->dev; | |
41ad427d AC |
658 | ret = usb_submit_urb(oob_port->write_urb, GFP_ATOMIC); |
659 | if (ret == 0) { | |
1da177e4 LT |
660 | oob_priv->dp_write_urb_in_use = 1; |
661 | count -= len; | |
662 | buf += len; | |
663 | } | |
1da177e4 | 664 | } |
c6d61269 AC |
665 | spin_unlock_irqrestore(&oob_priv->dp_port_lock, flags); |
666 | if (ret) | |
194343d9 GKH |
667 | dev_err(&port->dev, "%s: usb_submit_urb failed, ret=%d\n", |
668 | __func__, ret); | |
c6d61269 | 669 | return ret; |
1da177e4 LT |
670 | |
671 | } | |
672 | ||
673 | ||
674 | /* | |
41ad427d AC |
675 | * Digi Write In Band Command |
676 | * | |
677 | * Write commands on the given port. Commands are 4 | |
678 | * bytes each, multiple commands can be sent at once, and | |
679 | * no command will be split across USB packets. If timeout | |
680 | * is non-zero, write in band command will return after | |
681 | * waiting unsuccessfully for the URB status to clear for | |
682 | * timeout ticks. Returns 0 if successful, or a negative | |
683 | * error returned by digi_write. | |
684 | */ | |
1da177e4 | 685 | |
c6d61269 AC |
686 | static int digi_write_inb_command(struct usb_serial_port *port, |
687 | unsigned char *buf, int count, unsigned long timeout) | |
1da177e4 | 688 | { |
1da177e4 LT |
689 | int ret = 0; |
690 | int len; | |
691 | struct digi_port *priv = usb_get_serial_port_data(port); | |
692 | unsigned char *data = port->write_urb->transfer_buffer; | |
693 | unsigned long flags = 0; | |
694 | ||
c6d61269 AC |
695 | dbg("digi_write_inb_command: TOP: port=%d, count=%d", |
696 | priv->dp_port_num, count); | |
1da177e4 | 697 | |
c6d61269 | 698 | if (timeout) |
1da177e4 LT |
699 | timeout += jiffies; |
700 | else | |
701 | timeout = ULONG_MAX; | |
702 | ||
c6d61269 | 703 | spin_lock_irqsave(&priv->dp_port_lock, flags); |
41ad427d | 704 | while (count > 0 && ret == 0) { |
50de36f7 GKH |
705 | while (priv->dp_write_urb_in_use && |
706 | time_before(jiffies, timeout)) { | |
1da177e4 LT |
707 | cond_wait_interruptible_timeout_irqrestore( |
708 | &port->write_wait, DIGI_RETRY_TIMEOUT, | |
c6d61269 AC |
709 | &priv->dp_port_lock, flags); |
710 | if (signal_pending(current)) | |
711 | return -EINTR; | |
712 | spin_lock_irqsave(&priv->dp_port_lock, flags); | |
1da177e4 LT |
713 | } |
714 | ||
715 | /* len must be a multiple of 4 and small enough to */ | |
716 | /* guarantee the write will send buffered data first, */ | |
717 | /* so commands are in order with data and not split */ | |
c6d61269 AC |
718 | len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); |
719 | if (len > 4) | |
1da177e4 LT |
720 | len &= ~3; |
721 | ||
722 | /* write any buffered data first */ | |
c6d61269 | 723 | if (priv->dp_out_buf_len > 0) { |
1da177e4 LT |
724 | data[0] = DIGI_CMD_SEND_DATA; |
725 | data[1] = priv->dp_out_buf_len; | |
c6d61269 AC |
726 | memcpy(data + 2, priv->dp_out_buf, |
727 | priv->dp_out_buf_len); | |
728 | memcpy(data + 2 + priv->dp_out_buf_len, buf, len); | |
1da177e4 | 729 | port->write_urb->transfer_buffer_length |
c6d61269 | 730 | = priv->dp_out_buf_len + 2 + len; |
1da177e4 | 731 | } else { |
c6d61269 | 732 | memcpy(data, buf, len); |
1da177e4 LT |
733 | port->write_urb->transfer_buffer_length = len; |
734 | } | |
735 | port->write_urb->dev = port->serial->dev; | |
736 | ||
41ad427d AC |
737 | ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); |
738 | if (ret == 0) { | |
1da177e4 LT |
739 | priv->dp_write_urb_in_use = 1; |
740 | priv->dp_out_buf_len = 0; | |
741 | count -= len; | |
742 | buf += len; | |
743 | } | |
744 | ||
745 | } | |
c6d61269 | 746 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); |
1da177e4 | 747 | |
c6d61269 | 748 | if (ret) |
194343d9 GKH |
749 | dev_err(&port->dev, |
750 | "%s: usb_submit_urb failed, ret=%d, port=%d\n", | |
441b62c1 | 751 | __func__, ret, priv->dp_port_num); |
c6d61269 | 752 | return ret; |
1da177e4 LT |
753 | } |
754 | ||
755 | ||
756 | /* | |
41ad427d AC |
757 | * Digi Set Modem Signals |
758 | * | |
759 | * Sets or clears DTR and RTS on the port, according to the | |
760 | * modem_signals argument. Use TIOCM_DTR and TIOCM_RTS flags | |
761 | * for the modem_signals argument. Returns 0 if successful, | |
762 | * -EINTR if interrupted while sleeping, or a non-zero error | |
763 | * returned by usb_submit_urb. | |
764 | */ | |
1da177e4 | 765 | |
c6d61269 AC |
766 | static int digi_set_modem_signals(struct usb_serial_port *port, |
767 | unsigned int modem_signals, int interruptible) | |
1da177e4 LT |
768 | { |
769 | ||
770 | int ret; | |
771 | struct digi_port *port_priv = usb_get_serial_port_data(port); | |
41ad427d | 772 | struct usb_serial_port *oob_port = (struct usb_serial_port *) ((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; |
1da177e4 LT |
773 | struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); |
774 | unsigned char *data = oob_port->write_urb->transfer_buffer; | |
775 | unsigned long flags = 0; | |
776 | ||
777 | ||
c6d61269 AC |
778 | dbg("digi_set_modem_signals: TOP: port=%d, modem_signals=0x%x", |
779 | port_priv->dp_port_num, modem_signals); | |
1da177e4 | 780 | |
c6d61269 AC |
781 | spin_lock_irqsave(&oob_priv->dp_port_lock, flags); |
782 | spin_lock(&port_priv->dp_port_lock); | |
1da177e4 | 783 | |
50de36f7 | 784 | while (oob_priv->dp_write_urb_in_use) { |
c6d61269 | 785 | spin_unlock(&port_priv->dp_port_lock); |
1da177e4 LT |
786 | cond_wait_interruptible_timeout_irqrestore( |
787 | &oob_port->write_wait, DIGI_RETRY_TIMEOUT, | |
c6d61269 AC |
788 | &oob_priv->dp_port_lock, flags); |
789 | if (interruptible && signal_pending(current)) | |
790 | return -EINTR; | |
791 | spin_lock_irqsave(&oob_priv->dp_port_lock, flags); | |
792 | spin_lock(&port_priv->dp_port_lock); | |
1da177e4 | 793 | } |
1da177e4 LT |
794 | data[0] = DIGI_CMD_SET_DTR_SIGNAL; |
795 | data[1] = port_priv->dp_port_num; | |
41ad427d AC |
796 | data[2] = (modem_signals & TIOCM_DTR) ? |
797 | DIGI_DTR_ACTIVE : DIGI_DTR_INACTIVE; | |
1da177e4 | 798 | data[3] = 0; |
1da177e4 LT |
799 | data[4] = DIGI_CMD_SET_RTS_SIGNAL; |
800 | data[5] = port_priv->dp_port_num; | |
41ad427d AC |
801 | data[6] = (modem_signals & TIOCM_RTS) ? |
802 | DIGI_RTS_ACTIVE : DIGI_RTS_INACTIVE; | |
1da177e4 LT |
803 | data[7] = 0; |
804 | ||
805 | oob_port->write_urb->transfer_buffer_length = 8; | |
806 | oob_port->write_urb->dev = port->serial->dev; | |
807 | ||
41ad427d AC |
808 | ret = usb_submit_urb(oob_port->write_urb, GFP_ATOMIC); |
809 | if (ret == 0) { | |
1da177e4 LT |
810 | oob_priv->dp_write_urb_in_use = 1; |
811 | port_priv->dp_modem_signals = | |
812 | (port_priv->dp_modem_signals&~(TIOCM_DTR|TIOCM_RTS)) | |
813 | | (modem_signals&(TIOCM_DTR|TIOCM_RTS)); | |
814 | } | |
c6d61269 AC |
815 | spin_unlock(&port_priv->dp_port_lock); |
816 | spin_unlock_irqrestore(&oob_priv->dp_port_lock, flags); | |
817 | if (ret) | |
194343d9 GKH |
818 | dev_err(&port->dev, "%s: usb_submit_urb failed, ret=%d\n", |
819 | __func__, ret); | |
c6d61269 | 820 | return ret; |
1da177e4 LT |
821 | } |
822 | ||
1da177e4 | 823 | /* |
41ad427d AC |
824 | * Digi Transmit Idle |
825 | * | |
826 | * Digi transmit idle waits, up to timeout ticks, for the transmitter | |
827 | * to go idle. It returns 0 if successful or a negative error. | |
828 | * | |
829 | * There are race conditions here if more than one process is calling | |
830 | * digi_transmit_idle on the same port at the same time. However, this | |
831 | * is only called from close, and only one process can be in close on a | |
832 | * port at a time, so its ok. | |
833 | */ | |
1da177e4 | 834 | |
c6d61269 AC |
835 | static int digi_transmit_idle(struct usb_serial_port *port, |
836 | unsigned long timeout) | |
1da177e4 | 837 | { |
1da177e4 LT |
838 | int ret; |
839 | unsigned char buf[2]; | |
840 | struct digi_port *priv = usb_get_serial_port_data(port); | |
841 | unsigned long flags = 0; | |
842 | ||
c6d61269 | 843 | spin_lock_irqsave(&priv->dp_port_lock, flags); |
1da177e4 | 844 | priv->dp_transmit_idle = 0; |
c6d61269 | 845 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); |
1da177e4 LT |
846 | |
847 | buf[0] = DIGI_CMD_TRANSMIT_IDLE; | |
848 | buf[1] = 0; | |
849 | ||
850 | timeout += jiffies; | |
851 | ||
41ad427d AC |
852 | ret = digi_write_inb_command(port, buf, 2, timeout - jiffies); |
853 | if (ret != 0) | |
c6d61269 | 854 | return ret; |
1da177e4 | 855 | |
c6d61269 | 856 | spin_lock_irqsave(&priv->dp_port_lock, flags); |
1da177e4 | 857 | |
41ad427d | 858 | while (time_before(jiffies, timeout) && !priv->dp_transmit_idle) { |
1da177e4 LT |
859 | cond_wait_interruptible_timeout_irqrestore( |
860 | &priv->dp_transmit_idle_wait, DIGI_RETRY_TIMEOUT, | |
c6d61269 AC |
861 | &priv->dp_port_lock, flags); |
862 | if (signal_pending(current)) | |
863 | return -EINTR; | |
864 | spin_lock_irqsave(&priv->dp_port_lock, flags); | |
1da177e4 | 865 | } |
1da177e4 | 866 | priv->dp_transmit_idle = 0; |
c6d61269 AC |
867 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); |
868 | return 0; | |
1da177e4 LT |
869 | |
870 | } | |
871 | ||
872 | ||
95da310e | 873 | static void digi_rx_throttle(struct tty_struct *tty) |
1da177e4 | 874 | { |
1da177e4 | 875 | unsigned long flags; |
95da310e | 876 | struct usb_serial_port *port = tty->driver_data; |
1da177e4 LT |
877 | struct digi_port *priv = usb_get_serial_port_data(port); |
878 | ||
879 | ||
c6d61269 | 880 | dbg("digi_rx_throttle: TOP: port=%d", priv->dp_port_num); |
1da177e4 LT |
881 | |
882 | /* stop receiving characters by not resubmitting the read urb */ | |
c6d61269 | 883 | spin_lock_irqsave(&priv->dp_port_lock, flags); |
1da177e4 LT |
884 | priv->dp_throttled = 1; |
885 | priv->dp_throttle_restart = 0; | |
c6d61269 | 886 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); |
1da177e4 LT |
887 | } |
888 | ||
889 | ||
95da310e | 890 | static void digi_rx_unthrottle(struct tty_struct *tty) |
1da177e4 | 891 | { |
1da177e4 | 892 | int ret = 0; |
1da177e4 | 893 | unsigned long flags; |
95da310e | 894 | struct usb_serial_port *port = tty->driver_data; |
1da177e4 | 895 | struct digi_port *priv = usb_get_serial_port_data(port); |
1da177e4 | 896 | |
c6d61269 | 897 | dbg("digi_rx_unthrottle: TOP: port=%d", priv->dp_port_num); |
1da177e4 | 898 | |
c6d61269 | 899 | spin_lock_irqsave(&priv->dp_port_lock, flags); |
1da177e4 | 900 | |
39892da4 ON |
901 | /* turn throttle off */ |
902 | priv->dp_throttled = 0; | |
39892da4 | 903 | priv->dp_throttle_restart = 0; |
1da177e4 LT |
904 | |
905 | /* restart read chain */ | |
c6d61269 | 906 | if (priv->dp_throttle_restart) { |
1da177e4 | 907 | port->read_urb->dev = port->serial->dev; |
c6d61269 | 908 | ret = usb_submit_urb(port->read_urb, GFP_ATOMIC); |
1da177e4 LT |
909 | } |
910 | ||
c6d61269 | 911 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); |
1da177e4 | 912 | |
c6d61269 | 913 | if (ret) |
194343d9 GKH |
914 | dev_err(&port->dev, |
915 | "%s: usb_submit_urb failed, ret=%d, port=%d\n", | |
441b62c1 | 916 | __func__, ret, priv->dp_port_num); |
1da177e4 LT |
917 | } |
918 | ||
919 | ||
41ad427d | 920 | static void digi_set_termios(struct tty_struct *tty, |
95da310e | 921 | struct usb_serial_port *port, struct ktermios *old_termios) |
1da177e4 | 922 | { |
1da177e4 | 923 | struct digi_port *priv = usb_get_serial_port_data(port); |
c6d61269 AC |
924 | unsigned int iflag = tty->termios->c_iflag; |
925 | unsigned int cflag = tty->termios->c_cflag; | |
1da177e4 LT |
926 | unsigned int old_iflag = old_termios->c_iflag; |
927 | unsigned int old_cflag = old_termios->c_cflag; | |
928 | unsigned char buf[32]; | |
929 | unsigned int modem_signals; | |
41ad427d | 930 | int arg, ret; |
1da177e4 | 931 | int i = 0; |
c6d61269 | 932 | speed_t baud; |
1da177e4 | 933 | |
c6d61269 | 934 | dbg("digi_set_termios: TOP: port=%d, iflag=0x%x, old_iflag=0x%x, cflag=0x%x, old_cflag=0x%x", priv->dp_port_num, iflag, old_iflag, cflag, old_cflag); |
1da177e4 LT |
935 | |
936 | /* set baud rate */ | |
41ad427d AC |
937 | baud = tty_get_baud_rate(tty); |
938 | if (baud != tty_termios_baud_rate(old_termios)) { | |
1da177e4 LT |
939 | arg = -1; |
940 | ||
941 | /* reassert DTR and (maybe) RTS on transition from B0 */ | |
c6d61269 | 942 | if ((old_cflag&CBAUD) == B0) { |
1da177e4 LT |
943 | /* don't set RTS if using hardware flow control */ |
944 | /* and throttling input */ | |
945 | modem_signals = TIOCM_DTR; | |
c6d61269 AC |
946 | if (!(tty->termios->c_cflag & CRTSCTS) || |
947 | !test_bit(TTY_THROTTLED, &tty->flags)) | |
1da177e4 | 948 | modem_signals |= TIOCM_RTS; |
c6d61269 | 949 | digi_set_modem_signals(port, modem_signals, 1); |
1da177e4 | 950 | } |
c6d61269 | 951 | switch (baud) { |
41ad427d AC |
952 | /* drop DTR and RTS on transition to B0 */ |
953 | case 0: digi_set_modem_signals(port, 0, 1); break; | |
954 | case 50: arg = DIGI_BAUD_50; break; | |
955 | case 75: arg = DIGI_BAUD_75; break; | |
956 | case 110: arg = DIGI_BAUD_110; break; | |
957 | case 150: arg = DIGI_BAUD_150; break; | |
958 | case 200: arg = DIGI_BAUD_200; break; | |
959 | case 300: arg = DIGI_BAUD_300; break; | |
960 | case 600: arg = DIGI_BAUD_600; break; | |
961 | case 1200: arg = DIGI_BAUD_1200; break; | |
962 | case 1800: arg = DIGI_BAUD_1800; break; | |
963 | case 2400: arg = DIGI_BAUD_2400; break; | |
964 | case 4800: arg = DIGI_BAUD_4800; break; | |
965 | case 9600: arg = DIGI_BAUD_9600; break; | |
966 | case 19200: arg = DIGI_BAUD_19200; break; | |
967 | case 38400: arg = DIGI_BAUD_38400; break; | |
968 | case 57600: arg = DIGI_BAUD_57600; break; | |
969 | case 115200: arg = DIGI_BAUD_115200; break; | |
970 | case 230400: arg = DIGI_BAUD_230400; break; | |
971 | case 460800: arg = DIGI_BAUD_460800; break; | |
972 | default: | |
973 | arg = DIGI_BAUD_9600; | |
974 | baud = 9600; | |
975 | break; | |
1da177e4 | 976 | } |
c6d61269 | 977 | if (arg != -1) { |
1da177e4 LT |
978 | buf[i++] = DIGI_CMD_SET_BAUD_RATE; |
979 | buf[i++] = priv->dp_port_num; | |
980 | buf[i++] = arg; | |
981 | buf[i++] = 0; | |
982 | } | |
1da177e4 | 983 | } |
1da177e4 | 984 | /* set parity */ |
7fa36a99 AC |
985 | tty->termios->c_cflag &= ~CMSPAR; |
986 | ||
c6d61269 AC |
987 | if ((cflag&(PARENB|PARODD)) != (old_cflag&(PARENB|PARODD))) { |
988 | if (cflag&PARENB) { | |
989 | if (cflag&PARODD) | |
1da177e4 LT |
990 | arg = DIGI_PARITY_ODD; |
991 | else | |
992 | arg = DIGI_PARITY_EVEN; | |
993 | } else { | |
994 | arg = DIGI_PARITY_NONE; | |
995 | } | |
1da177e4 LT |
996 | buf[i++] = DIGI_CMD_SET_PARITY; |
997 | buf[i++] = priv->dp_port_num; | |
998 | buf[i++] = arg; | |
999 | buf[i++] = 0; | |
1da177e4 | 1000 | } |
1da177e4 | 1001 | /* set word size */ |
c6d61269 | 1002 | if ((cflag&CSIZE) != (old_cflag&CSIZE)) { |
1da177e4 | 1003 | arg = -1; |
c6d61269 | 1004 | switch (cflag&CSIZE) { |
1da177e4 LT |
1005 | case CS5: arg = DIGI_WORD_SIZE_5; break; |
1006 | case CS6: arg = DIGI_WORD_SIZE_6; break; | |
1007 | case CS7: arg = DIGI_WORD_SIZE_7; break; | |
1008 | case CS8: arg = DIGI_WORD_SIZE_8; break; | |
1009 | default: | |
c6d61269 AC |
1010 | dbg("digi_set_termios: can't handle word size %d", |
1011 | (cflag&CSIZE)); | |
1da177e4 LT |
1012 | break; |
1013 | } | |
1014 | ||
c6d61269 | 1015 | if (arg != -1) { |
1da177e4 LT |
1016 | buf[i++] = DIGI_CMD_SET_WORD_SIZE; |
1017 | buf[i++] = priv->dp_port_num; | |
1018 | buf[i++] = arg; | |
1019 | buf[i++] = 0; | |
1020 | } | |
1021 | ||
1022 | } | |
1023 | ||
1024 | /* set stop bits */ | |
c6d61269 | 1025 | if ((cflag&CSTOPB) != (old_cflag&CSTOPB)) { |
1da177e4 | 1026 | |
c6d61269 | 1027 | if ((cflag&CSTOPB)) |
1da177e4 LT |
1028 | arg = DIGI_STOP_BITS_2; |
1029 | else | |
1030 | arg = DIGI_STOP_BITS_1; | |
1031 | ||
1032 | buf[i++] = DIGI_CMD_SET_STOP_BITS; | |
1033 | buf[i++] = priv->dp_port_num; | |
1034 | buf[i++] = arg; | |
1035 | buf[i++] = 0; | |
1036 | ||
1037 | } | |
1038 | ||
1039 | /* set input flow control */ | |
c6d61269 AC |
1040 | if ((iflag&IXOFF) != (old_iflag&IXOFF) |
1041 | || (cflag&CRTSCTS) != (old_cflag&CRTSCTS)) { | |
1da177e4 | 1042 | arg = 0; |
c6d61269 | 1043 | if (iflag&IXOFF) |
1da177e4 LT |
1044 | arg |= DIGI_INPUT_FLOW_CONTROL_XON_XOFF; |
1045 | else | |
1046 | arg &= ~DIGI_INPUT_FLOW_CONTROL_XON_XOFF; | |
1047 | ||
c6d61269 | 1048 | if (cflag&CRTSCTS) { |
1da177e4 LT |
1049 | arg |= DIGI_INPUT_FLOW_CONTROL_RTS; |
1050 | ||
1051 | /* On USB-4 it is necessary to assert RTS prior */ | |
1052 | /* to selecting RTS input flow control. */ | |
1053 | buf[i++] = DIGI_CMD_SET_RTS_SIGNAL; | |
1054 | buf[i++] = priv->dp_port_num; | |
1055 | buf[i++] = DIGI_RTS_ACTIVE; | |
1056 | buf[i++] = 0; | |
1057 | ||
1058 | } else { | |
1059 | arg &= ~DIGI_INPUT_FLOW_CONTROL_RTS; | |
1060 | } | |
1da177e4 LT |
1061 | buf[i++] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; |
1062 | buf[i++] = priv->dp_port_num; | |
1063 | buf[i++] = arg; | |
1064 | buf[i++] = 0; | |
1da177e4 LT |
1065 | } |
1066 | ||
1067 | /* set output flow control */ | |
7fa36a99 AC |
1068 | if ((iflag & IXON) != (old_iflag & IXON) |
1069 | || (cflag & CRTSCTS) != (old_cflag & CRTSCTS)) { | |
1da177e4 | 1070 | arg = 0; |
7fa36a99 | 1071 | if (iflag & IXON) |
1da177e4 LT |
1072 | arg |= DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; |
1073 | else | |
1074 | arg &= ~DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; | |
1075 | ||
7fa36a99 | 1076 | if (cflag & CRTSCTS) { |
1da177e4 LT |
1077 | arg |= DIGI_OUTPUT_FLOW_CONTROL_CTS; |
1078 | } else { | |
1079 | arg &= ~DIGI_OUTPUT_FLOW_CONTROL_CTS; | |
c6d61269 | 1080 | tty->hw_stopped = 0; |
1da177e4 LT |
1081 | } |
1082 | ||
1083 | buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; | |
1084 | buf[i++] = priv->dp_port_num; | |
1085 | buf[i++] = arg; | |
1086 | buf[i++] = 0; | |
1da177e4 LT |
1087 | } |
1088 | ||
1089 | /* set receive enable/disable */ | |
7fa36a99 AC |
1090 | if ((cflag & CREAD) != (old_cflag & CREAD)) { |
1091 | if (cflag & CREAD) | |
1da177e4 LT |
1092 | arg = DIGI_ENABLE; |
1093 | else | |
1094 | arg = DIGI_DISABLE; | |
1095 | ||
1096 | buf[i++] = DIGI_CMD_RECEIVE_ENABLE; | |
1097 | buf[i++] = priv->dp_port_num; | |
1098 | buf[i++] = arg; | |
1099 | buf[i++] = 0; | |
1da177e4 | 1100 | } |
41ad427d AC |
1101 | ret = digi_write_oob_command(port, buf, i, 1); |
1102 | if (ret != 0) | |
c6d61269 | 1103 | dbg("digi_set_termios: write oob failed, ret=%d", ret); |
7fa36a99 | 1104 | tty_encode_baud_rate(tty, baud, baud); |
1da177e4 LT |
1105 | } |
1106 | ||
1107 | ||
95da310e | 1108 | static void digi_break_ctl(struct tty_struct *tty, int break_state) |
1da177e4 | 1109 | { |
95da310e | 1110 | struct usb_serial_port *port = tty->driver_data; |
1da177e4 LT |
1111 | unsigned char buf[4]; |
1112 | ||
1da177e4 LT |
1113 | buf[0] = DIGI_CMD_BREAK_CONTROL; |
1114 | buf[1] = 2; /* length */ | |
1115 | buf[2] = break_state ? 1 : 0; | |
1116 | buf[3] = 0; /* pad */ | |
c6d61269 | 1117 | digi_write_inb_command(port, buf, 4, 0); |
1da177e4 LT |
1118 | } |
1119 | ||
1120 | ||
95da310e | 1121 | static int digi_tiocmget(struct tty_struct *tty, struct file *file) |
1da177e4 | 1122 | { |
95da310e | 1123 | struct usb_serial_port *port = tty->driver_data; |
1da177e4 LT |
1124 | struct digi_port *priv = usb_get_serial_port_data(port); |
1125 | unsigned int val; | |
1126 | unsigned long flags; | |
1127 | ||
441b62c1 | 1128 | dbg("%s: TOP: port=%d", __func__, priv->dp_port_num); |
1da177e4 | 1129 | |
c6d61269 | 1130 | spin_lock_irqsave(&priv->dp_port_lock, flags); |
1da177e4 | 1131 | val = priv->dp_modem_signals; |
c6d61269 | 1132 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); |
1da177e4 LT |
1133 | return val; |
1134 | } | |
1135 | ||
1136 | ||
95da310e | 1137 | static int digi_tiocmset(struct tty_struct *tty, struct file *file, |
c6d61269 | 1138 | unsigned int set, unsigned int clear) |
1da177e4 | 1139 | { |
95da310e | 1140 | struct usb_serial_port *port = tty->driver_data; |
1da177e4 LT |
1141 | struct digi_port *priv = usb_get_serial_port_data(port); |
1142 | unsigned int val; | |
1143 | unsigned long flags; | |
1144 | ||
441b62c1 | 1145 | dbg("%s: TOP: port=%d", __func__, priv->dp_port_num); |
1da177e4 | 1146 | |
c6d61269 | 1147 | spin_lock_irqsave(&priv->dp_port_lock, flags); |
1da177e4 | 1148 | val = (priv->dp_modem_signals & ~clear) | set; |
c6d61269 AC |
1149 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); |
1150 | return digi_set_modem_signals(port, val, 1); | |
1da177e4 LT |
1151 | } |
1152 | ||
1153 | ||
95da310e AC |
1154 | static int digi_write(struct tty_struct *tty, struct usb_serial_port *port, |
1155 | const unsigned char *buf, int count) | |
1da177e4 LT |
1156 | { |
1157 | ||
41ad427d | 1158 | int ret, data_len, new_len; |
1da177e4 LT |
1159 | struct digi_port *priv = usb_get_serial_port_data(port); |
1160 | unsigned char *data = port->write_urb->transfer_buffer; | |
1161 | unsigned long flags = 0; | |
1162 | ||
c6d61269 AC |
1163 | dbg("digi_write: TOP: port=%d, count=%d, in_interrupt=%ld", |
1164 | priv->dp_port_num, count, in_interrupt()); | |
1da177e4 LT |
1165 | |
1166 | /* copy user data (which can sleep) before getting spin lock */ | |
c6d61269 AC |
1167 | count = min(count, port->bulk_out_size-2); |
1168 | count = min(64, count); | |
1da177e4 LT |
1169 | |
1170 | /* be sure only one write proceeds at a time */ | |
1171 | /* there are races on the port private buffer */ | |
c6d61269 | 1172 | spin_lock_irqsave(&priv->dp_port_lock, flags); |
1da177e4 LT |
1173 | |
1174 | /* wait for urb status clear to submit another urb */ | |
50de36f7 | 1175 | if (priv->dp_write_urb_in_use) { |
1da177e4 | 1176 | /* buffer data if count is 1 (probably put_char) if possible */ |
c6d61269 | 1177 | if (count == 1 && priv->dp_out_buf_len < DIGI_OUT_BUF_SIZE) { |
1da177e4 LT |
1178 | priv->dp_out_buf[priv->dp_out_buf_len++] = *buf; |
1179 | new_len = 1; | |
1180 | } else { | |
1181 | new_len = 0; | |
1182 | } | |
c6d61269 AC |
1183 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); |
1184 | return new_len; | |
1da177e4 LT |
1185 | } |
1186 | ||
1187 | /* allow space for any buffered data and for new data, up to */ | |
1188 | /* transfer buffer size - 2 (for command and length bytes) */ | |
1189 | new_len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); | |
1190 | data_len = new_len + priv->dp_out_buf_len; | |
1191 | ||
c6d61269 AC |
1192 | if (data_len == 0) { |
1193 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); | |
1194 | return 0; | |
1da177e4 LT |
1195 | } |
1196 | ||
1197 | port->write_urb->transfer_buffer_length = data_len+2; | |
1198 | port->write_urb->dev = port->serial->dev; | |
1199 | ||
1200 | *data++ = DIGI_CMD_SEND_DATA; | |
1201 | *data++ = data_len; | |
1202 | ||
1203 | /* copy in buffered data first */ | |
c6d61269 | 1204 | memcpy(data, priv->dp_out_buf, priv->dp_out_buf_len); |
1da177e4 LT |
1205 | data += priv->dp_out_buf_len; |
1206 | ||
1207 | /* copy in new data */ | |
c6d61269 | 1208 | memcpy(data, buf, new_len); |
1da177e4 | 1209 | |
41ad427d AC |
1210 | ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); |
1211 | if (ret == 0) { | |
1da177e4 LT |
1212 | priv->dp_write_urb_in_use = 1; |
1213 | ret = new_len; | |
1214 | priv->dp_out_buf_len = 0; | |
1215 | } | |
1216 | ||
1217 | /* return length of new data written, or error */ | |
c6d61269 AC |
1218 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); |
1219 | if (ret < 0) | |
194343d9 GKH |
1220 | dev_err(&port->dev, |
1221 | "%s: usb_submit_urb failed, ret=%d, port=%d\n", | |
441b62c1 | 1222 | __func__, ret, priv->dp_port_num); |
c6d61269 AC |
1223 | dbg("digi_write: returning %d", ret); |
1224 | return ret; | |
1da177e4 | 1225 | |
41ad427d | 1226 | } |
1da177e4 | 1227 | |
c6d61269 | 1228 | static void digi_write_bulk_callback(struct urb *urb) |
1da177e4 LT |
1229 | { |
1230 | ||
cdc97792 | 1231 | struct usb_serial_port *port = urb->context; |
1da177e4 LT |
1232 | struct usb_serial *serial; |
1233 | struct digi_port *priv; | |
1234 | struct digi_serial *serial_priv; | |
1235 | int ret = 0; | |
85d75107 | 1236 | int status = urb->status; |
1da177e4 | 1237 | |
50de36f7 | 1238 | dbg("digi_write_bulk_callback: TOP, status=%d", status); |
1da177e4 LT |
1239 | |
1240 | /* port and serial sanity check */ | |
41ad427d | 1241 | if (port == NULL || (priv = usb_get_serial_port_data(port)) == NULL) { |
194343d9 GKH |
1242 | dev_err(&port->dev, |
1243 | "%s: port or port->private is NULL, status=%d\n", | |
1244 | __func__, status); | |
1da177e4 LT |
1245 | return; |
1246 | } | |
1247 | serial = port->serial; | |
41ad427d | 1248 | if (serial == NULL || (serial_priv = usb_get_serial_data(serial)) == NULL) { |
194343d9 GKH |
1249 | dev_err(&port->dev, |
1250 | "%s: serial or serial->private is NULL, status=%d\n", | |
1251 | __func__, status); | |
1da177e4 LT |
1252 | return; |
1253 | } | |
1254 | ||
1255 | /* handle oob callback */ | |
c6d61269 AC |
1256 | if (priv->dp_port_num == serial_priv->ds_oob_port_num) { |
1257 | dbg("digi_write_bulk_callback: oob callback"); | |
1258 | spin_lock(&priv->dp_port_lock); | |
1da177e4 | 1259 | priv->dp_write_urb_in_use = 0; |
c6d61269 AC |
1260 | wake_up_interruptible(&port->write_wait); |
1261 | spin_unlock(&priv->dp_port_lock); | |
1da177e4 LT |
1262 | return; |
1263 | } | |
1264 | ||
1265 | /* try to send any buffered data on this port, if it is open */ | |
c6d61269 | 1266 | spin_lock(&priv->dp_port_lock); |
1da177e4 | 1267 | priv->dp_write_urb_in_use = 0; |
50de36f7 | 1268 | if (port->port.count && priv->dp_out_buf_len > 0) { |
1da177e4 LT |
1269 | *((unsigned char *)(port->write_urb->transfer_buffer)) |
1270 | = (unsigned char)DIGI_CMD_SEND_DATA; | |
41ad427d | 1271 | *((unsigned char *)(port->write_urb->transfer_buffer) + 1) |
1da177e4 | 1272 | = (unsigned char)priv->dp_out_buf_len; |
41ad427d AC |
1273 | port->write_urb->transfer_buffer_length = |
1274 | priv->dp_out_buf_len + 2; | |
1da177e4 | 1275 | port->write_urb->dev = serial->dev; |
41ad427d | 1276 | memcpy(port->write_urb->transfer_buffer + 2, priv->dp_out_buf, |
c6d61269 | 1277 | priv->dp_out_buf_len); |
41ad427d AC |
1278 | ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); |
1279 | if (ret == 0) { | |
1da177e4 LT |
1280 | priv->dp_write_urb_in_use = 1; |
1281 | priv->dp_out_buf_len = 0; | |
1282 | } | |
1da177e4 | 1283 | } |
1da177e4 | 1284 | /* wake up processes sleeping on writes immediately */ |
c6d61269 | 1285 | digi_wakeup_write(port); |
1da177e4 LT |
1286 | /* also queue up a wakeup at scheduler time, in case we */ |
1287 | /* lost the race in write_chan(). */ | |
1288 | schedule_work(&priv->dp_wakeup_work); | |
1289 | ||
c6d61269 AC |
1290 | spin_unlock(&priv->dp_port_lock); |
1291 | if (ret) | |
194343d9 GKH |
1292 | dev_err(&port->dev, |
1293 | "%s: usb_submit_urb failed, ret=%d, port=%d\n", | |
441b62c1 | 1294 | __func__, ret, priv->dp_port_num); |
1da177e4 LT |
1295 | } |
1296 | ||
95da310e | 1297 | static int digi_write_room(struct tty_struct *tty) |
1da177e4 | 1298 | { |
95da310e | 1299 | struct usb_serial_port *port = tty->driver_data; |
1da177e4 | 1300 | struct digi_port *priv = usb_get_serial_port_data(port); |
95da310e | 1301 | int room; |
1da177e4 LT |
1302 | unsigned long flags = 0; |
1303 | ||
c6d61269 | 1304 | spin_lock_irqsave(&priv->dp_port_lock, flags); |
1da177e4 | 1305 | |
50de36f7 | 1306 | if (priv->dp_write_urb_in_use) |
1da177e4 LT |
1307 | room = 0; |
1308 | else | |
1309 | room = port->bulk_out_size - 2 - priv->dp_out_buf_len; | |
1310 | ||
c6d61269 AC |
1311 | spin_unlock_irqrestore(&priv->dp_port_lock, flags); |
1312 | dbg("digi_write_room: port=%d, room=%d", priv->dp_port_num, room); | |
1313 | return room; | |
1da177e4 LT |
1314 | |
1315 | } | |
1316 | ||
95da310e | 1317 | static int digi_chars_in_buffer(struct tty_struct *tty) |
1da177e4 | 1318 | { |
95da310e | 1319 | struct usb_serial_port *port = tty->driver_data; |
1da177e4 LT |
1320 | struct digi_port *priv = usb_get_serial_port_data(port); |
1321 | ||
50de36f7 | 1322 | if (priv->dp_write_urb_in_use) { |
c6d61269 AC |
1323 | dbg("digi_chars_in_buffer: port=%d, chars=%d", |
1324 | priv->dp_port_num, port->bulk_out_size - 2); | |
1325 | /* return(port->bulk_out_size - 2); */ | |
1326 | return 256; | |
1da177e4 | 1327 | } else { |
c6d61269 AC |
1328 | dbg("digi_chars_in_buffer: port=%d, chars=%d", |
1329 | priv->dp_port_num, priv->dp_out_buf_len); | |
1330 | return priv->dp_out_buf_len; | |
1da177e4 LT |
1331 | } |
1332 | ||
1333 | } | |
1334 | ||
335f8514 AC |
1335 | static void digi_dtr_rts(struct usb_serial_port *port, int on) |
1336 | { | |
1337 | /* Adjust DTR and RTS */ | |
1338 | digi_set_modem_signals(port, on * (TIOCM_DTR|TIOCM_RTS), 1); | |
1339 | } | |
1340 | ||
1341 | static int digi_carrier_raised(struct usb_serial_port *port) | |
1342 | { | |
1343 | struct digi_port *priv = usb_get_serial_port_data(port); | |
1344 | if (priv->dp_modem_signals & TIOCM_CD) | |
1345 | return 1; | |
1346 | return 0; | |
1347 | } | |
1da177e4 | 1348 | |
a509a7e4 | 1349 | static int digi_open(struct tty_struct *tty, struct usb_serial_port *port) |
1da177e4 | 1350 | { |
1da177e4 LT |
1351 | int ret; |
1352 | unsigned char buf[32]; | |
1353 | struct digi_port *priv = usb_get_serial_port_data(port); | |
606d099c | 1354 | struct ktermios not_termios; |
1da177e4 | 1355 | |
c6d61269 | 1356 | dbg("digi_open: TOP: port=%d, open_count=%d", |
95da310e | 1357 | priv->dp_port_num, port->port.count); |
1da177e4 LT |
1358 | |
1359 | /* be sure the device is started up */ | |
c6d61269 AC |
1360 | if (digi_startup_device(port->serial) != 0) |
1361 | return -ENXIO; | |
1da177e4 | 1362 | |
1da177e4 LT |
1363 | /* read modem signals automatically whenever they change */ |
1364 | buf[0] = DIGI_CMD_READ_INPUT_SIGNALS; | |
1365 | buf[1] = priv->dp_port_num; | |
1366 | buf[2] = DIGI_ENABLE; | |
1367 | buf[3] = 0; | |
1368 | ||
1369 | /* flush fifos */ | |
1370 | buf[4] = DIGI_CMD_IFLUSH_FIFO; | |
1371 | buf[5] = priv->dp_port_num; | |
1372 | buf[6] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; | |
1373 | buf[7] = 0; | |
1374 | ||
41ad427d AC |
1375 | ret = digi_write_oob_command(port, buf, 8, 1); |
1376 | if (ret != 0) | |
c6d61269 | 1377 | dbg("digi_open: write oob failed, ret=%d", ret); |
1da177e4 LT |
1378 | |
1379 | /* set termios settings */ | |
95da310e AC |
1380 | if (tty) { |
1381 | not_termios.c_cflag = ~tty->termios->c_cflag; | |
1382 | not_termios.c_iflag = ~tty->termios->c_iflag; | |
1383 | digi_set_termios(tty, port, ¬_termios); | |
1384 | } | |
c6d61269 | 1385 | return 0; |
1da177e4 LT |
1386 | } |
1387 | ||
1388 | ||
335f8514 | 1389 | static void digi_close(struct usb_serial_port *port) |
1da177e4 LT |
1390 | { |
1391 | DEFINE_WAIT(wait); | |
1392 | int ret; | |
1393 | unsigned char buf[32]; | |
1da177e4 | 1394 | struct digi_port *priv = usb_get_serial_port_data(port); |
1da177e4 | 1395 | |
c6d61269 | 1396 | dbg("digi_close: TOP: port=%d, open_count=%d", |
95da310e | 1397 | priv->dp_port_num, port->port.count); |
1da177e4 | 1398 | |
0915f490 | 1399 | mutex_lock(&port->serial->disc_mutex); |
1da177e4 | 1400 | /* if disconnected, just clear flags */ |
0915f490 | 1401 | if (port->serial->disconnected) |
1da177e4 LT |
1402 | goto exit; |
1403 | ||
1da177e4 | 1404 | if (port->serial->dev) { |
335f8514 AC |
1405 | /* FIXME: Transmit idle belongs in the wait_unti_sent path */ |
1406 | digi_transmit_idle(port, DIGI_CLOSE_TIMEOUT); | |
1da177e4 LT |
1407 | |
1408 | /* disable input flow control */ | |
1409 | buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; | |
1410 | buf[1] = priv->dp_port_num; | |
1411 | buf[2] = DIGI_DISABLE; | |
1412 | buf[3] = 0; | |
1413 | ||
1414 | /* disable output flow control */ | |
1415 | buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; | |
1416 | buf[5] = priv->dp_port_num; | |
1417 | buf[6] = DIGI_DISABLE; | |
1418 | buf[7] = 0; | |
1419 | ||
1420 | /* disable reading modem signals automatically */ | |
1421 | buf[8] = DIGI_CMD_READ_INPUT_SIGNALS; | |
1422 | buf[9] = priv->dp_port_num; | |
1423 | buf[10] = DIGI_DISABLE; | |
1424 | buf[11] = 0; | |
1425 | ||
1426 | /* disable receive */ | |
1427 | buf[12] = DIGI_CMD_RECEIVE_ENABLE; | |
1428 | buf[13] = priv->dp_port_num; | |
1429 | buf[14] = DIGI_DISABLE; | |
1430 | buf[15] = 0; | |
1431 | ||
1432 | /* flush fifos */ | |
1433 | buf[16] = DIGI_CMD_IFLUSH_FIFO; | |
1434 | buf[17] = priv->dp_port_num; | |
1435 | buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; | |
1436 | buf[19] = 0; | |
1437 | ||
41ad427d AC |
1438 | ret = digi_write_oob_command(port, buf, 20, 0); |
1439 | if (ret != 0) | |
c6d61269 | 1440 | dbg("digi_close: write oob failed, ret=%d", ret); |
1da177e4 LT |
1441 | |
1442 | /* wait for final commands on oob port to complete */ | |
41ad427d AC |
1443 | prepare_to_wait(&priv->dp_flush_wait, &wait, |
1444 | TASK_INTERRUPTIBLE); | |
1da177e4 LT |
1445 | schedule_timeout(DIGI_CLOSE_TIMEOUT); |
1446 | finish_wait(&priv->dp_flush_wait, &wait); | |
1447 | ||
1448 | /* shutdown any outstanding bulk writes */ | |
1449 | usb_kill_urb(port->write_urb); | |
1450 | } | |
1da177e4 | 1451 | exit: |
0915f490 | 1452 | spin_lock_irq(&priv->dp_port_lock); |
1da177e4 | 1453 | priv->dp_write_urb_in_use = 0; |
c6d61269 | 1454 | wake_up_interruptible(&priv->dp_close_wait); |
0915f490 ON |
1455 | spin_unlock_irq(&priv->dp_port_lock); |
1456 | mutex_unlock(&port->serial->disc_mutex); | |
c6d61269 | 1457 | dbg("digi_close: done"); |
1da177e4 LT |
1458 | } |
1459 | ||
1460 | ||
1461 | /* | |
41ad427d AC |
1462 | * Digi Startup Device |
1463 | * | |
1464 | * Starts reads on all ports. Must be called AFTER startup, with | |
1465 | * urbs initialized. Returns 0 if successful, non-zero error otherwise. | |
1466 | */ | |
1da177e4 | 1467 | |
c6d61269 | 1468 | static int digi_startup_device(struct usb_serial *serial) |
1da177e4 | 1469 | { |
41ad427d | 1470 | int i, ret = 0; |
1da177e4 LT |
1471 | struct digi_serial *serial_priv = usb_get_serial_data(serial); |
1472 | struct usb_serial_port *port; | |
1473 | ||
1da177e4 | 1474 | /* be sure this happens exactly once */ |
c6d61269 AC |
1475 | spin_lock(&serial_priv->ds_serial_lock); |
1476 | if (serial_priv->ds_device_started) { | |
1477 | spin_unlock(&serial_priv->ds_serial_lock); | |
1478 | return 0; | |
1da177e4 LT |
1479 | } |
1480 | serial_priv->ds_device_started = 1; | |
c6d61269 | 1481 | spin_unlock(&serial_priv->ds_serial_lock); |
1da177e4 LT |
1482 | |
1483 | /* start reading from each bulk in endpoint for the device */ | |
1484 | /* set USB_DISABLE_SPD flag for write bulk urbs */ | |
c6d61269 | 1485 | for (i = 0; i < serial->type->num_ports + 1; i++) { |
1da177e4 | 1486 | port = serial->port[i]; |
1da177e4 | 1487 | port->write_urb->dev = port->serial->dev; |
41ad427d AC |
1488 | ret = usb_submit_urb(port->read_urb, GFP_KERNEL); |
1489 | if (ret != 0) { | |
194343d9 GKH |
1490 | dev_err(&port->dev, |
1491 | "%s: usb_submit_urb failed, ret=%d, port=%d\n", | |
1492 | __func__, ret, i); | |
1da177e4 LT |
1493 | break; |
1494 | } | |
1da177e4 | 1495 | } |
c6d61269 | 1496 | return ret; |
1da177e4 LT |
1497 | } |
1498 | ||
1499 | ||
c6d61269 | 1500 | static int digi_startup(struct usb_serial *serial) |
1da177e4 LT |
1501 | { |
1502 | ||
1503 | int i; | |
1504 | struct digi_port *priv; | |
1505 | struct digi_serial *serial_priv; | |
1506 | ||
c6d61269 | 1507 | dbg("digi_startup: TOP"); |
1da177e4 LT |
1508 | |
1509 | /* allocate the private data structures for all ports */ | |
1510 | /* number of regular ports + 1 for the out-of-band port */ | |
41ad427d | 1511 | for (i = 0; i < serial->type->num_ports + 1; i++) { |
1da177e4 | 1512 | /* allocate port private structure */ |
c6d61269 AC |
1513 | priv = kmalloc(sizeof(struct digi_port), GFP_KERNEL); |
1514 | if (priv == NULL) { | |
1515 | while (--i >= 0) | |
1516 | kfree(usb_get_serial_port_data(serial->port[i])); | |
1517 | return 1; /* error */ | |
1da177e4 LT |
1518 | } |
1519 | ||
1520 | /* initialize port private structure */ | |
c6d61269 | 1521 | spin_lock_init(&priv->dp_port_lock); |
1da177e4 LT |
1522 | priv->dp_port_num = i; |
1523 | priv->dp_out_buf_len = 0; | |
1da177e4 LT |
1524 | priv->dp_write_urb_in_use = 0; |
1525 | priv->dp_modem_signals = 0; | |
c6d61269 | 1526 | init_waitqueue_head(&priv->dp_modem_change_wait); |
1da177e4 | 1527 | priv->dp_transmit_idle = 0; |
c6d61269 | 1528 | init_waitqueue_head(&priv->dp_transmit_idle_wait); |
1da177e4 LT |
1529 | priv->dp_throttled = 0; |
1530 | priv->dp_throttle_restart = 0; | |
c6d61269 | 1531 | init_waitqueue_head(&priv->dp_flush_wait); |
c6d61269 | 1532 | init_waitqueue_head(&priv->dp_close_wait); |
c4028958 DH |
1533 | INIT_WORK(&priv->dp_wakeup_work, digi_wakeup_write_lock); |
1534 | priv->dp_port = serial->port[i]; | |
1da177e4 | 1535 | /* initialize write wait queue for this port */ |
c6d61269 | 1536 | init_waitqueue_head(&serial->port[i]->write_wait); |
1da177e4 LT |
1537 | |
1538 | usb_set_serial_port_data(serial->port[i], priv); | |
1539 | } | |
1540 | ||
1541 | /* allocate serial private structure */ | |
c6d61269 AC |
1542 | serial_priv = kmalloc(sizeof(struct digi_serial), GFP_KERNEL); |
1543 | if (serial_priv == NULL) { | |
1544 | for (i = 0; i < serial->type->num_ports + 1; i++) | |
1545 | kfree(usb_get_serial_port_data(serial->port[i])); | |
1546 | return 1; /* error */ | |
1da177e4 LT |
1547 | } |
1548 | ||
1549 | /* initialize serial private structure */ | |
c6d61269 | 1550 | spin_lock_init(&serial_priv->ds_serial_lock); |
1da177e4 LT |
1551 | serial_priv->ds_oob_port_num = serial->type->num_ports; |
1552 | serial_priv->ds_oob_port = serial->port[serial_priv->ds_oob_port_num]; | |
1553 | serial_priv->ds_device_started = 0; | |
1554 | usb_set_serial_data(serial, serial_priv); | |
1555 | ||
c6d61269 | 1556 | return 0; |
1da177e4 LT |
1557 | } |
1558 | ||
1559 | ||
f9c99bb8 | 1560 | static void digi_disconnect(struct usb_serial *serial) |
1da177e4 | 1561 | { |
1da177e4 | 1562 | int i; |
f9c99bb8 | 1563 | dbg("digi_disconnect: TOP, in_interrupt()=%ld", in_interrupt()); |
1da177e4 LT |
1564 | |
1565 | /* stop reads and writes on all ports */ | |
c6d61269 | 1566 | for (i = 0; i < serial->type->num_ports + 1; i++) { |
1da177e4 LT |
1567 | usb_kill_urb(serial->port[i]->read_urb); |
1568 | usb_kill_urb(serial->port[i]->write_urb); | |
1569 | } | |
f9c99bb8 AS |
1570 | } |
1571 | ||
1572 | ||
1573 | static void digi_release(struct usb_serial *serial) | |
1574 | { | |
1575 | int i; | |
1576 | dbg("digi_release: TOP, in_interrupt()=%ld", in_interrupt()); | |
1da177e4 LT |
1577 | |
1578 | /* free the private data structures for all ports */ | |
1579 | /* number of regular ports + 1 for the out-of-band port */ | |
41ad427d | 1580 | for (i = 0; i < serial->type->num_ports + 1; i++) |
c6d61269 AC |
1581 | kfree(usb_get_serial_port_data(serial->port[i])); |
1582 | kfree(usb_get_serial_data(serial)); | |
1da177e4 LT |
1583 | } |
1584 | ||
1585 | ||
c6d61269 | 1586 | static void digi_read_bulk_callback(struct urb *urb) |
1da177e4 | 1587 | { |
cdc97792 | 1588 | struct usb_serial_port *port = urb->context; |
1da177e4 LT |
1589 | struct digi_port *priv; |
1590 | struct digi_serial *serial_priv; | |
1591 | int ret; | |
85d75107 | 1592 | int status = urb->status; |
1da177e4 | 1593 | |
c6d61269 | 1594 | dbg("digi_read_bulk_callback: TOP"); |
1da177e4 LT |
1595 | |
1596 | /* port sanity check, do not resubmit if port is not valid */ | |
194343d9 GKH |
1597 | if (port == NULL) |
1598 | return; | |
1599 | priv = usb_get_serial_port_data(port); | |
1600 | if (priv == NULL) { | |
1601 | dev_err(&port->dev, "%s: port->private is NULL, status=%d\n", | |
1602 | __func__, status); | |
1da177e4 LT |
1603 | return; |
1604 | } | |
c6d61269 | 1605 | if (port->serial == NULL || |
41ad427d | 1606 | (serial_priv = usb_get_serial_data(port->serial)) == NULL) { |
194343d9 GKH |
1607 | dev_err(&port->dev, "%s: serial is bad or serial->private " |
1608 | "is NULL, status=%d\n", __func__, status); | |
1da177e4 LT |
1609 | return; |
1610 | } | |
1611 | ||
1612 | /* do not resubmit urb if it has any status error */ | |
85d75107 | 1613 | if (status) { |
194343d9 GKH |
1614 | dev_err(&port->dev, |
1615 | "%s: nonzero read bulk status: status=%d, port=%d\n", | |
1616 | __func__, status, priv->dp_port_num); | |
1da177e4 LT |
1617 | return; |
1618 | } | |
1619 | ||
1620 | /* handle oob or inb callback, do not resubmit if error */ | |
c6d61269 AC |
1621 | if (priv->dp_port_num == serial_priv->ds_oob_port_num) { |
1622 | if (digi_read_oob_callback(urb) != 0) | |
1da177e4 LT |
1623 | return; |
1624 | } else { | |
c6d61269 | 1625 | if (digi_read_inb_callback(urb) != 0) |
1da177e4 LT |
1626 | return; |
1627 | } | |
1628 | ||
1629 | /* continue read */ | |
1630 | urb->dev = port->serial->dev; | |
41ad427d AC |
1631 | ret = usb_submit_urb(urb, GFP_ATOMIC); |
1632 | if (ret != 0) { | |
194343d9 GKH |
1633 | dev_err(&port->dev, |
1634 | "%s: failed resubmitting urb, ret=%d, port=%d\n", | |
1635 | __func__, ret, priv->dp_port_num); | |
1da177e4 LT |
1636 | } |
1637 | ||
1638 | } | |
1639 | ||
41ad427d AC |
1640 | /* |
1641 | * Digi Read INB Callback | |
1642 | * | |
1643 | * Digi Read INB Callback handles reads on the in band ports, sending | |
1644 | * the data on to the tty subsystem. When called we know port and | |
1645 | * port->private are not NULL and port->serial has been validated. | |
1646 | * It returns 0 if successful, 1 if successful but the port is | |
1647 | * throttled, and -1 if the sanity checks failed. | |
1648 | */ | |
1da177e4 | 1649 | |
c6d61269 | 1650 | static int digi_read_inb_callback(struct urb *urb) |
1da177e4 LT |
1651 | { |
1652 | ||
cdc97792 | 1653 | struct usb_serial_port *port = urb->context; |
4a90f09b | 1654 | struct tty_struct *tty; |
1da177e4 LT |
1655 | struct digi_port *priv = usb_get_serial_port_data(port); |
1656 | int opcode = ((unsigned char *)urb->transfer_buffer)[0]; | |
1657 | int len = ((unsigned char *)urb->transfer_buffer)[1]; | |
85d75107 | 1658 | int port_status = ((unsigned char *)urb->transfer_buffer)[2]; |
41ad427d AC |
1659 | unsigned char *data = ((unsigned char *)urb->transfer_buffer) + 3; |
1660 | int flag, throttled; | |
33f0f88f | 1661 | int i; |
85d75107 | 1662 | int status = urb->status; |
1da177e4 LT |
1663 | |
1664 | /* do not process callbacks on closed ports */ | |
1665 | /* but do continue the read chain */ | |
95da310e | 1666 | if (port->port.count == 0) |
c6d61269 | 1667 | return 0; |
1da177e4 LT |
1668 | |
1669 | /* short/multiple packet check */ | |
c6d61269 | 1670 | if (urb->actual_length != len + 2) { |
194343d9 | 1671 | dev_err(&port->dev, "%s: INCOMPLETE OR MULTIPLE PACKET, " |
50de36f7 | 1672 | "status=%d, port=%d, opcode=%d, len=%d, " |
194343d9 GKH |
1673 | "actual_length=%d, status=%d\n", __func__, status, |
1674 | priv->dp_port_num, opcode, len, urb->actual_length, | |
1675 | port_status); | |
c6d61269 | 1676 | return -1; |
1da177e4 LT |
1677 | } |
1678 | ||
4a90f09b | 1679 | tty = tty_port_tty_get(&port->port); |
c6d61269 | 1680 | spin_lock(&priv->dp_port_lock); |
1da177e4 LT |
1681 | |
1682 | /* check for throttle; if set, do not resubmit read urb */ | |
1683 | /* indicate the read chain needs to be restarted on unthrottle */ | |
1684 | throttled = priv->dp_throttled; | |
c6d61269 | 1685 | if (throttled) |
1da177e4 LT |
1686 | priv->dp_throttle_restart = 1; |
1687 | ||
1688 | /* receive data */ | |
c6d61269 | 1689 | if (opcode == DIGI_CMD_RECEIVE_DATA) { |
85d75107 | 1690 | /* get flag from port_status */ |
1da177e4 LT |
1691 | flag = 0; |
1692 | ||
1693 | /* overrun is special, not associated with a char */ | |
c6d61269 AC |
1694 | if (port_status & DIGI_OVERRUN_ERROR) |
1695 | tty_insert_flip_char(tty, 0, TTY_OVERRUN); | |
1da177e4 LT |
1696 | |
1697 | /* break takes precedence over parity, */ | |
1698 | /* which takes precedence over framing errors */ | |
c6d61269 | 1699 | if (port_status & DIGI_BREAK_ERROR) |
1da177e4 | 1700 | flag = TTY_BREAK; |
c6d61269 | 1701 | else if (port_status & DIGI_PARITY_ERROR) |
1da177e4 | 1702 | flag = TTY_PARITY; |
c6d61269 | 1703 | else if (port_status & DIGI_FRAMING_ERROR) |
1da177e4 | 1704 | flag = TTY_FRAME; |
1da177e4 | 1705 | |
85d75107 | 1706 | /* data length is len-1 (one byte of len is port_status) */ |
1da177e4 LT |
1707 | --len; |
1708 | ||
39892da4 | 1709 | len = tty_buffer_request_room(tty, len); |
c6d61269 | 1710 | if (len > 0) { |
39892da4 | 1711 | /* Hot path */ |
c6d61269 | 1712 | if (flag == TTY_NORMAL) |
39892da4 ON |
1713 | tty_insert_flip_string(tty, data, len); |
1714 | else { | |
41ad427d AC |
1715 | for (i = 0; i < len; i++) |
1716 | tty_insert_flip_char(tty, | |
1717 | data[i], flag); | |
1da177e4 | 1718 | } |
c6d61269 | 1719 | tty_flip_buffer_push(tty); |
1da177e4 | 1720 | } |
1da177e4 | 1721 | } |
c6d61269 | 1722 | spin_unlock(&priv->dp_port_lock); |
4a90f09b | 1723 | tty_kref_put(tty); |
1da177e4 | 1724 | |
c6d61269 | 1725 | if (opcode == DIGI_CMD_RECEIVE_DISABLE) |
441b62c1 | 1726 | dbg("%s: got RECEIVE_DISABLE", __func__); |
c6d61269 | 1727 | else if (opcode != DIGI_CMD_RECEIVE_DATA) |
441b62c1 | 1728 | dbg("%s: unknown opcode: %d", __func__, opcode); |
1da177e4 | 1729 | |
41ad427d | 1730 | return throttled ? 1 : 0; |
1da177e4 LT |
1731 | |
1732 | } | |
1733 | ||
1734 | ||
41ad427d AC |
1735 | /* |
1736 | * Digi Read OOB Callback | |
1737 | * | |
1738 | * Digi Read OOB Callback handles reads on the out of band port. | |
1739 | * When called we know port and port->private are not NULL and | |
1740 | * the port->serial is valid. It returns 0 if successful, and | |
1741 | * -1 if the sanity checks failed. | |
1742 | */ | |
1da177e4 | 1743 | |
c6d61269 | 1744 | static int digi_read_oob_callback(struct urb *urb) |
1da177e4 LT |
1745 | { |
1746 | ||
cdc97792 | 1747 | struct usb_serial_port *port = urb->context; |
1da177e4 | 1748 | struct usb_serial *serial = port->serial; |
4a90f09b | 1749 | struct tty_struct *tty; |
1da177e4 LT |
1750 | struct digi_port *priv = usb_get_serial_port_data(port); |
1751 | int opcode, line, status, val; | |
1752 | int i; | |
41ad427d | 1753 | unsigned int rts; |
1da177e4 | 1754 | |
c6d61269 AC |
1755 | dbg("digi_read_oob_callback: port=%d, len=%d", |
1756 | priv->dp_port_num, urb->actual_length); | |
1da177e4 LT |
1757 | |
1758 | /* handle each oob command */ | |
41ad427d | 1759 | for (i = 0; i < urb->actual_length - 3;) { |
1da177e4 LT |
1760 | opcode = ((unsigned char *)urb->transfer_buffer)[i++]; |
1761 | line = ((unsigned char *)urb->transfer_buffer)[i++]; | |
1762 | status = ((unsigned char *)urb->transfer_buffer)[i++]; | |
1763 | val = ((unsigned char *)urb->transfer_buffer)[i++]; | |
1764 | ||
c6d61269 AC |
1765 | dbg("digi_read_oob_callback: opcode=%d, line=%d, status=%d, val=%d", |
1766 | opcode, line, status, val); | |
1da177e4 | 1767 | |
c6d61269 | 1768 | if (status != 0 || line >= serial->type->num_ports) |
1da177e4 LT |
1769 | continue; |
1770 | ||
1771 | port = serial->port[line]; | |
1772 | ||
41ad427d AC |
1773 | priv = usb_get_serial_port_data(port); |
1774 | if (priv == NULL) | |
1da177e4 LT |
1775 | return -1; |
1776 | ||
4a90f09b | 1777 | tty = tty_port_tty_get(&port->port); |
41ad427d AC |
1778 | rts = 0; |
1779 | if (port->port.count) | |
4a90f09b AC |
1780 | rts = tty->termios->c_cflag & CRTSCTS; |
1781 | ||
c6d61269 AC |
1782 | if (opcode == DIGI_CMD_READ_INPUT_SIGNALS) { |
1783 | spin_lock(&priv->dp_port_lock); | |
1da177e4 | 1784 | /* convert from digi flags to termiox flags */ |
c6d61269 | 1785 | if (val & DIGI_READ_INPUT_SIGNALS_CTS) { |
1da177e4 LT |
1786 | priv->dp_modem_signals |= TIOCM_CTS; |
1787 | /* port must be open to use tty struct */ | |
41ad427d | 1788 | if (rts) { |
4a90f09b | 1789 | tty->hw_stopped = 0; |
c6d61269 | 1790 | digi_wakeup_write(port); |
1da177e4 LT |
1791 | } |
1792 | } else { | |
1793 | priv->dp_modem_signals &= ~TIOCM_CTS; | |
1794 | /* port must be open to use tty struct */ | |
41ad427d | 1795 | if (rts) |
4a90f09b | 1796 | tty->hw_stopped = 1; |
1da177e4 | 1797 | } |
c6d61269 | 1798 | if (val & DIGI_READ_INPUT_SIGNALS_DSR) |
1da177e4 LT |
1799 | priv->dp_modem_signals |= TIOCM_DSR; |
1800 | else | |
1801 | priv->dp_modem_signals &= ~TIOCM_DSR; | |
c6d61269 | 1802 | if (val & DIGI_READ_INPUT_SIGNALS_RI) |
1da177e4 LT |
1803 | priv->dp_modem_signals |= TIOCM_RI; |
1804 | else | |
1805 | priv->dp_modem_signals &= ~TIOCM_RI; | |
c6d61269 | 1806 | if (val & DIGI_READ_INPUT_SIGNALS_DCD) |
1da177e4 LT |
1807 | priv->dp_modem_signals |= TIOCM_CD; |
1808 | else | |
1809 | priv->dp_modem_signals &= ~TIOCM_CD; | |
1810 | ||
c6d61269 AC |
1811 | wake_up_interruptible(&priv->dp_modem_change_wait); |
1812 | spin_unlock(&priv->dp_port_lock); | |
1813 | } else if (opcode == DIGI_CMD_TRANSMIT_IDLE) { | |
1814 | spin_lock(&priv->dp_port_lock); | |
1da177e4 | 1815 | priv->dp_transmit_idle = 1; |
c6d61269 AC |
1816 | wake_up_interruptible(&priv->dp_transmit_idle_wait); |
1817 | spin_unlock(&priv->dp_port_lock); | |
1818 | } else if (opcode == DIGI_CMD_IFLUSH_FIFO) { | |
1819 | wake_up_interruptible(&priv->dp_flush_wait); | |
1da177e4 | 1820 | } |
4a90f09b | 1821 | tty_kref_put(tty); |
1da177e4 | 1822 | } |
c6d61269 | 1823 | return 0; |
1da177e4 LT |
1824 | |
1825 | } | |
1826 | ||
c6d61269 | 1827 | static int __init digi_init(void) |
1da177e4 LT |
1828 | { |
1829 | int retval; | |
1830 | retval = usb_serial_register(&digi_acceleport_2_device); | |
1831 | if (retval) | |
1832 | goto failed_acceleport_2_device; | |
1833 | retval = usb_serial_register(&digi_acceleport_4_device); | |
41ad427d | 1834 | if (retval) |
1da177e4 LT |
1835 | goto failed_acceleport_4_device; |
1836 | retval = usb_register(&digi_driver); | |
1837 | if (retval) | |
1838 | goto failed_usb_register; | |
c197a8db GKH |
1839 | printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":" |
1840 | DRIVER_DESC "\n"); | |
1da177e4 LT |
1841 | return 0; |
1842 | failed_usb_register: | |
1843 | usb_serial_deregister(&digi_acceleport_4_device); | |
1844 | failed_acceleport_4_device: | |
1845 | usb_serial_deregister(&digi_acceleport_2_device); | |
1846 | failed_acceleport_2_device: | |
1847 | return retval; | |
1848 | } | |
1849 | ||
1da177e4 LT |
1850 | static void __exit digi_exit (void) |
1851 | { | |
c6d61269 AC |
1852 | usb_deregister(&digi_driver); |
1853 | usb_serial_deregister(&digi_acceleport_2_device); | |
1854 | usb_serial_deregister(&digi_acceleport_4_device); | |
1da177e4 LT |
1855 | } |
1856 | ||
1857 | ||
1858 | module_init(digi_init); | |
1859 | module_exit(digi_exit); | |
1860 | ||
1861 | ||
c6d61269 AC |
1862 | MODULE_AUTHOR(DRIVER_AUTHOR); |
1863 | MODULE_DESCRIPTION(DRIVER_DESC); | |
1da177e4 LT |
1864 | MODULE_LICENSE("GPL"); |
1865 | ||
1866 | module_param(debug, bool, S_IRUGO | S_IWUSR); | |
1867 | MODULE_PARM_DESC(debug, "Debug enabled or not"); |