Commit | Line | Data |
---|---|---|
91777826 JW |
1 | /* |
2 | * Standalone EHCI usb debug driver | |
3 | * | |
4 | * Originally written by: | |
5 | * Eric W. Biederman" <ebiederm@xmission.com> and | |
6 | * Yinghai Lu <yhlu.kernel@gmail.com> | |
7 | * | |
8 | * Changes for early/late printk and HW errata: | |
9 | * Jason Wessel <jason.wessel@windriver.com> | |
10 | * Copyright (C) 2009 Wind River Systems, Inc. | |
11 | * | |
12 | */ | |
13 | ||
df6c5169 JW |
14 | #include <linux/console.h> |
15 | #include <linux/errno.h> | |
91777826 | 16 | #include <linux/module.h> |
df6c5169 JW |
17 | #include <linux/pci_regs.h> |
18 | #include <linux/pci_ids.h> | |
19 | #include <linux/usb/ch9.h> | |
20 | #include <linux/usb/ehci_def.h> | |
21 | #include <linux/delay.h> | |
4fe1da4e JW |
22 | #include <linux/serial_core.h> |
23 | #include <linux/kgdb.h> | |
24 | #include <linux/kthread.h> | |
df6c5169 JW |
25 | #include <asm/io.h> |
26 | #include <asm/pci-direct.h> | |
27 | #include <asm/fixmap.h> | |
28 | ||
91777826 JW |
29 | /* The code here is intended to talk directly to the EHCI debug port |
30 | * and does not require that you have any kind of USB host controller | |
31 | * drivers or USB device drivers compiled into the kernel. | |
32 | * | |
33 | * If you make a change to anything in here, the following test cases | |
34 | * need to pass where a USB debug device works in the following | |
35 | * configurations. | |
36 | * | |
37 | * 1. boot args: earlyprintk=dbgp | |
38 | * o kernel compiled with # CONFIG_USB_EHCI_HCD is not set | |
39 | * o kernel compiled with CONFIG_USB_EHCI_HCD=y | |
40 | * 2. boot args: earlyprintk=dbgp,keep | |
41 | * o kernel compiled with # CONFIG_USB_EHCI_HCD is not set | |
42 | * o kernel compiled with CONFIG_USB_EHCI_HCD=y | |
43 | * 3. boot args: earlyprintk=dbgp console=ttyUSB0 | |
44 | * o kernel has CONFIG_USB_EHCI_HCD=y and | |
45 | * CONFIG_USB_SERIAL_DEBUG=y | |
46 | * 4. boot args: earlyprintk=vga,dbgp | |
47 | * o kernel compiled with # CONFIG_USB_EHCI_HCD is not set | |
48 | * o kernel compiled with CONFIG_USB_EHCI_HCD=y | |
49 | * | |
50 | * For the 4th configuration you can turn on or off the DBGP_DEBUG | |
51 | * such that you can debug the dbgp device's driver code. | |
52 | */ | |
53 | ||
54 | static int dbgp_phys_port = 1; | |
56faf0f9 | 55 | |
df6c5169 JW |
56 | static struct ehci_caps __iomem *ehci_caps; |
57 | static struct ehci_regs __iomem *ehci_regs; | |
58 | static struct ehci_dbg_port __iomem *ehci_debug; | |
91777826 | 59 | static int dbgp_not_safe; /* Cannot use debug device during ehci reset */ |
df6c5169 | 60 | static unsigned int dbgp_endpoint_out; |
4fe1da4e | 61 | static unsigned int dbgp_endpoint_in; |
df6c5169 JW |
62 | |
63 | struct ehci_dev { | |
64 | u32 bus; | |
65 | u32 slot; | |
66 | u32 func; | |
67 | }; | |
68 | ||
69 | static struct ehci_dev ehci_dev; | |
70 | ||
71 | #define USB_DEBUG_DEVNUM 127 | |
72 | ||
91777826 JW |
73 | #ifdef DBGP_DEBUG |
74 | #define dbgp_printk printk | |
75 | static void dbgp_ehci_status(char *str) | |
76 | { | |
77 | if (!ehci_debug) | |
78 | return; | |
79 | dbgp_printk("dbgp: %s\n", str); | |
80 | dbgp_printk(" Debug control: %08x", readl(&ehci_debug->control)); | |
81 | dbgp_printk(" ehci cmd : %08x", readl(&ehci_regs->command)); | |
82 | dbgp_printk(" ehci conf flg: %08x\n", | |
83 | readl(&ehci_regs->configured_flag)); | |
84 | dbgp_printk(" ehci status : %08x", readl(&ehci_regs->status)); | |
85 | dbgp_printk(" ehci portsc : %08x\n", | |
86 | readl(&ehci_regs->port_status[dbgp_phys_port - 1])); | |
87 | } | |
88 | #else | |
89 | static inline void dbgp_ehci_status(char *str) { } | |
90 | static inline void dbgp_printk(const char *fmt, ...) { } | |
91 | #endif | |
92 | ||
df6c5169 JW |
93 | static inline u32 dbgp_len_update(u32 x, u32 len) |
94 | { | |
95 | return (x & ~0x0f) | (len & 0x0f); | |
96 | } | |
97 | ||
4fe1da4e JW |
98 | #ifdef CONFIG_KGDB |
99 | static struct kgdb_io kgdbdbgp_io_ops; | |
100 | #define dbgp_kgdb_mode (dbg_io_ops == &kgdbdbgp_io_ops) | |
101 | #else | |
102 | #define dbgp_kgdb_mode (0) | |
103 | #endif | |
104 | ||
df6c5169 JW |
105 | /* |
106 | * USB Packet IDs (PIDs) | |
107 | */ | |
108 | ||
109 | /* token */ | |
110 | #define USB_PID_OUT 0xe1 | |
111 | #define USB_PID_IN 0x69 | |
112 | #define USB_PID_SOF 0xa5 | |
113 | #define USB_PID_SETUP 0x2d | |
114 | /* handshake */ | |
115 | #define USB_PID_ACK 0xd2 | |
116 | #define USB_PID_NAK 0x5a | |
117 | #define USB_PID_STALL 0x1e | |
118 | #define USB_PID_NYET 0x96 | |
119 | /* data */ | |
120 | #define USB_PID_DATA0 0xc3 | |
121 | #define USB_PID_DATA1 0x4b | |
122 | #define USB_PID_DATA2 0x87 | |
123 | #define USB_PID_MDATA 0x0f | |
124 | /* Special */ | |
125 | #define USB_PID_PREAMBLE 0x3c | |
126 | #define USB_PID_ERR 0x3c | |
127 | #define USB_PID_SPLIT 0x78 | |
128 | #define USB_PID_PING 0xb4 | |
129 | #define USB_PID_UNDEF_0 0xf0 | |
130 | ||
131 | #define USB_PID_DATA_TOGGLE 0x88 | |
132 | #define DBGP_CLAIM (DBGP_OWNER | DBGP_ENABLED | DBGP_INUSE) | |
133 | ||
134 | #define PCI_CAP_ID_EHCI_DEBUG 0xa | |
135 | ||
136 | #define HUB_ROOT_RESET_TIME 50 /* times are in msec */ | |
137 | #define HUB_SHORT_RESET_TIME 10 | |
138 | #define HUB_LONG_RESET_TIME 200 | |
139 | #define HUB_RESET_TIMEOUT 500 | |
140 | ||
141 | #define DBGP_MAX_PACKET 8 | |
91777826 | 142 | #define DBGP_TIMEOUT (250 * 1000) |
815e173e JW |
143 | #define DBGP_LOOPS 1000 |
144 | ||
145 | static inline u32 dbgp_pid_write_update(u32 x, u32 tok) | |
146 | { | |
147 | static int data0 = USB_PID_DATA1; | |
148 | data0 ^= USB_PID_DATA_TOGGLE; | |
149 | return (x & 0xffff0000) | (data0 << 8) | (tok & 0xff); | |
150 | } | |
151 | ||
152 | static inline u32 dbgp_pid_read_update(u32 x, u32 tok) | |
153 | { | |
154 | return (x & 0xffff0000) | (USB_PID_DATA0 << 8) | (tok & 0xff); | |
155 | } | |
df6c5169 JW |
156 | |
157 | static int dbgp_wait_until_complete(void) | |
158 | { | |
159 | u32 ctrl; | |
91777826 | 160 | int loop = DBGP_TIMEOUT; |
df6c5169 JW |
161 | |
162 | do { | |
163 | ctrl = readl(&ehci_debug->control); | |
164 | /* Stop when the transaction is finished */ | |
165 | if (ctrl & DBGP_DONE) | |
166 | break; | |
91777826 | 167 | udelay(1); |
df6c5169 JW |
168 | } while (--loop > 0); |
169 | ||
170 | if (!loop) | |
91777826 | 171 | return -DBGP_TIMEOUT; |
df6c5169 JW |
172 | |
173 | /* | |
174 | * Now that we have observed the completed transaction, | |
175 | * clear the done bit. | |
176 | */ | |
177 | writel(ctrl | DBGP_DONE, &ehci_debug->control); | |
178 | return (ctrl & DBGP_ERROR) ? -DBGP_ERRCODE(ctrl) : DBGP_LEN(ctrl); | |
179 | } | |
180 | ||
91777826 | 181 | static inline void dbgp_mdelay(int ms) |
df6c5169 JW |
182 | { |
183 | int i; | |
184 | ||
185 | while (ms--) { | |
186 | for (i = 0; i < 1000; i++) | |
187 | outb(0x1, 0x80); | |
188 | } | |
189 | } | |
190 | ||
191 | static void dbgp_breath(void) | |
192 | { | |
193 | /* Sleep to give the debug port a chance to breathe */ | |
194 | } | |
195 | ||
4fe1da4e | 196 | static int dbgp_wait_until_done(unsigned ctrl, int loop) |
df6c5169 JW |
197 | { |
198 | u32 pids, lpid; | |
199 | int ret; | |
df6c5169 JW |
200 | |
201 | retry: | |
202 | writel(ctrl | DBGP_GO, &ehci_debug->control); | |
203 | ret = dbgp_wait_until_complete(); | |
204 | pids = readl(&ehci_debug->pids); | |
205 | lpid = DBGP_PID_GET(pids); | |
206 | ||
91777826 JW |
207 | if (ret < 0) { |
208 | /* A -DBGP_TIMEOUT failure here means the device has | |
209 | * failed, perhaps because it was unplugged, in which | |
210 | * case we do not want to hang the system so the dbgp | |
211 | * will be marked as unsafe to use. EHCI reset is the | |
212 | * only way to recover if you unplug the dbgp device. | |
213 | */ | |
214 | if (ret == -DBGP_TIMEOUT && !dbgp_not_safe) | |
215 | dbgp_not_safe = 1; | |
815e173e JW |
216 | if (ret == -DBGP_ERR_BAD && --loop > 0) |
217 | goto retry; | |
df6c5169 | 218 | return ret; |
91777826 | 219 | } |
df6c5169 JW |
220 | |
221 | /* | |
222 | * If the port is getting full or it has dropped data | |
223 | * start pacing ourselves, not necessary but it's friendly. | |
224 | */ | |
225 | if ((lpid == USB_PID_NAK) || (lpid == USB_PID_NYET)) | |
226 | dbgp_breath(); | |
227 | ||
228 | /* If I get a NACK reissue the transmission */ | |
229 | if (lpid == USB_PID_NAK) { | |
230 | if (--loop > 0) | |
231 | goto retry; | |
232 | } | |
233 | ||
234 | return ret; | |
235 | } | |
236 | ||
91777826 | 237 | static inline void dbgp_set_data(const void *buf, int size) |
df6c5169 JW |
238 | { |
239 | const unsigned char *bytes = buf; | |
240 | u32 lo, hi; | |
241 | int i; | |
242 | ||
243 | lo = hi = 0; | |
244 | for (i = 0; i < 4 && i < size; i++) | |
245 | lo |= bytes[i] << (8*i); | |
246 | for (; i < 8 && i < size; i++) | |
247 | hi |= bytes[i] << (8*(i - 4)); | |
248 | writel(lo, &ehci_debug->data03); | |
249 | writel(hi, &ehci_debug->data47); | |
250 | } | |
251 | ||
91777826 | 252 | static inline void dbgp_get_data(void *buf, int size) |
df6c5169 JW |
253 | { |
254 | unsigned char *bytes = buf; | |
255 | u32 lo, hi; | |
256 | int i; | |
257 | ||
258 | lo = readl(&ehci_debug->data03); | |
259 | hi = readl(&ehci_debug->data47); | |
260 | for (i = 0; i < 4 && i < size; i++) | |
261 | bytes[i] = (lo >> (8*i)) & 0xff; | |
262 | for (; i < 8 && i < size; i++) | |
263 | bytes[i] = (hi >> (8*(i - 4))) & 0xff; | |
264 | } | |
265 | ||
815e173e JW |
266 | static int dbgp_bulk_write(unsigned devnum, unsigned endpoint, |
267 | const char *bytes, int size) | |
df6c5169 | 268 | { |
815e173e JW |
269 | int ret; |
270 | u32 addr; | |
68d2956a | 271 | u32 pids, ctrl; |
df6c5169 | 272 | |
815e173e JW |
273 | if (size > DBGP_MAX_PACKET) |
274 | return -1; | |
275 | ||
276 | addr = DBGP_EPADDR(devnum, endpoint); | |
277 | ||
df6c5169 | 278 | pids = readl(&ehci_debug->pids); |
815e173e | 279 | pids = dbgp_pid_write_update(pids, USB_PID_OUT); |
df6c5169 JW |
280 | |
281 | ctrl = readl(&ehci_debug->control); | |
282 | ctrl = dbgp_len_update(ctrl, size); | |
283 | ctrl |= DBGP_OUT; | |
284 | ctrl |= DBGP_GO; | |
285 | ||
286 | dbgp_set_data(bytes, size); | |
287 | writel(addr, &ehci_debug->address); | |
288 | writel(pids, &ehci_debug->pids); | |
4fe1da4e | 289 | ret = dbgp_wait_until_done(ctrl, DBGP_LOOPS); |
df6c5169 JW |
290 | |
291 | return ret; | |
292 | } | |
293 | ||
91777826 | 294 | static int dbgp_bulk_read(unsigned devnum, unsigned endpoint, void *data, |
4fe1da4e | 295 | int size, int loops) |
df6c5169 JW |
296 | { |
297 | u32 pids, addr, ctrl; | |
298 | int ret; | |
299 | ||
300 | if (size > DBGP_MAX_PACKET) | |
301 | return -1; | |
302 | ||
303 | addr = DBGP_EPADDR(devnum, endpoint); | |
304 | ||
305 | pids = readl(&ehci_debug->pids); | |
815e173e | 306 | pids = dbgp_pid_read_update(pids, USB_PID_IN); |
df6c5169 JW |
307 | |
308 | ctrl = readl(&ehci_debug->control); | |
309 | ctrl = dbgp_len_update(ctrl, size); | |
310 | ctrl &= ~DBGP_OUT; | |
311 | ctrl |= DBGP_GO; | |
312 | ||
313 | writel(addr, &ehci_debug->address); | |
314 | writel(pids, &ehci_debug->pids); | |
4fe1da4e | 315 | ret = dbgp_wait_until_done(ctrl, loops); |
df6c5169 JW |
316 | if (ret < 0) |
317 | return ret; | |
318 | ||
319 | if (size > ret) | |
320 | size = ret; | |
321 | dbgp_get_data(data, size); | |
322 | return ret; | |
323 | } | |
324 | ||
91777826 | 325 | static int dbgp_control_msg(unsigned devnum, int requesttype, |
df6c5169 JW |
326 | int request, int value, int index, void *data, int size) |
327 | { | |
328 | u32 pids, addr, ctrl; | |
329 | struct usb_ctrlrequest req; | |
330 | int read; | |
331 | int ret; | |
332 | ||
333 | read = (requesttype & USB_DIR_IN) != 0; | |
334 | if (size > (read ? DBGP_MAX_PACKET:0)) | |
335 | return -1; | |
336 | ||
337 | /* Compute the control message */ | |
338 | req.bRequestType = requesttype; | |
339 | req.bRequest = request; | |
340 | req.wValue = cpu_to_le16(value); | |
341 | req.wIndex = cpu_to_le16(index); | |
342 | req.wLength = cpu_to_le16(size); | |
343 | ||
344 | pids = DBGP_PID_SET(USB_PID_DATA0, USB_PID_SETUP); | |
345 | addr = DBGP_EPADDR(devnum, 0); | |
346 | ||
347 | ctrl = readl(&ehci_debug->control); | |
348 | ctrl = dbgp_len_update(ctrl, sizeof(req)); | |
349 | ctrl |= DBGP_OUT; | |
350 | ctrl |= DBGP_GO; | |
351 | ||
352 | /* Send the setup message */ | |
353 | dbgp_set_data(&req, sizeof(req)); | |
354 | writel(addr, &ehci_debug->address); | |
355 | writel(pids, &ehci_debug->pids); | |
4fe1da4e | 356 | ret = dbgp_wait_until_done(ctrl, DBGP_LOOPS); |
df6c5169 JW |
357 | if (ret < 0) |
358 | return ret; | |
359 | ||
360 | /* Read the result */ | |
4fe1da4e | 361 | return dbgp_bulk_read(devnum, 0, data, size, DBGP_LOOPS); |
df6c5169 JW |
362 | } |
363 | ||
df6c5169 JW |
364 | /* Find a PCI capability */ |
365 | static u32 __init find_cap(u32 num, u32 slot, u32 func, int cap) | |
366 | { | |
367 | u8 pos; | |
368 | int bytes; | |
369 | ||
370 | if (!(read_pci_config_16(num, slot, func, PCI_STATUS) & | |
371 | PCI_STATUS_CAP_LIST)) | |
372 | return 0; | |
373 | ||
374 | pos = read_pci_config_byte(num, slot, func, PCI_CAPABILITY_LIST); | |
375 | for (bytes = 0; bytes < 48 && pos >= 0x40; bytes++) { | |
376 | u8 id; | |
377 | ||
378 | pos &= ~3; | |
379 | id = read_pci_config_byte(num, slot, func, pos+PCI_CAP_LIST_ID); | |
380 | if (id == 0xff) | |
381 | break; | |
382 | if (id == cap) | |
383 | return pos; | |
384 | ||
385 | pos = read_pci_config_byte(num, slot, func, | |
386 | pos+PCI_CAP_LIST_NEXT); | |
387 | } | |
388 | return 0; | |
389 | } | |
390 | ||
391 | static u32 __init __find_dbgp(u32 bus, u32 slot, u32 func) | |
392 | { | |
393 | u32 class; | |
394 | ||
395 | class = read_pci_config(bus, slot, func, PCI_CLASS_REVISION); | |
396 | if ((class >> 8) != PCI_CLASS_SERIAL_USB_EHCI) | |
397 | return 0; | |
398 | ||
399 | return find_cap(bus, slot, func, PCI_CAP_ID_EHCI_DEBUG); | |
400 | } | |
401 | ||
402 | static u32 __init find_dbgp(int ehci_num, u32 *rbus, u32 *rslot, u32 *rfunc) | |
403 | { | |
404 | u32 bus, slot, func; | |
405 | ||
406 | for (bus = 0; bus < 256; bus++) { | |
407 | for (slot = 0; slot < 32; slot++) { | |
408 | for (func = 0; func < 8; func++) { | |
409 | unsigned cap; | |
410 | ||
411 | cap = __find_dbgp(bus, slot, func); | |
412 | ||
413 | if (!cap) | |
414 | continue; | |
415 | if (ehci_num-- != 0) | |
416 | continue; | |
417 | *rbus = bus; | |
418 | *rslot = slot; | |
419 | *rfunc = func; | |
420 | return cap; | |
421 | } | |
422 | } | |
423 | } | |
424 | return 0; | |
425 | } | |
426 | ||
91777826 JW |
427 | static int dbgp_ehci_startup(void) |
428 | { | |
429 | u32 ctrl, cmd, status; | |
430 | int loop; | |
431 | ||
432 | /* Claim ownership, but do not enable yet */ | |
433 | ctrl = readl(&ehci_debug->control); | |
434 | ctrl |= DBGP_OWNER; | |
435 | ctrl &= ~(DBGP_ENABLED | DBGP_INUSE); | |
436 | writel(ctrl, &ehci_debug->control); | |
437 | udelay(1); | |
438 | ||
439 | dbgp_ehci_status("EHCI startup"); | |
440 | /* Start the ehci running */ | |
441 | cmd = readl(&ehci_regs->command); | |
442 | cmd &= ~(CMD_LRESET | CMD_IAAD | CMD_PSE | CMD_ASE | CMD_RESET); | |
443 | cmd |= CMD_RUN; | |
444 | writel(cmd, &ehci_regs->command); | |
445 | ||
446 | /* Ensure everything is routed to the EHCI */ | |
447 | writel(FLAG_CF, &ehci_regs->configured_flag); | |
448 | ||
449 | /* Wait until the controller is no longer halted */ | |
450 | loop = 10; | |
451 | do { | |
452 | status = readl(&ehci_regs->status); | |
453 | if (!(status & STS_HALT)) | |
454 | break; | |
455 | udelay(1); | |
456 | } while (--loop > 0); | |
457 | ||
458 | if (!loop) { | |
459 | dbgp_printk("ehci can not be started\n"); | |
460 | return -ENODEV; | |
461 | } | |
462 | dbgp_printk("ehci started\n"); | |
463 | return 0; | |
464 | } | |
465 | ||
466 | static int dbgp_ehci_controller_reset(void) | |
467 | { | |
468 | int loop = 250 * 1000; | |
469 | u32 cmd; | |
470 | ||
471 | /* Reset the EHCI controller */ | |
472 | cmd = readl(&ehci_regs->command); | |
473 | cmd |= CMD_RESET; | |
474 | writel(cmd, &ehci_regs->command); | |
475 | do { | |
476 | cmd = readl(&ehci_regs->command); | |
477 | } while ((cmd & CMD_RESET) && (--loop > 0)); | |
478 | ||
479 | if (!loop) { | |
480 | dbgp_printk("can not reset ehci\n"); | |
481 | return -1; | |
482 | } | |
483 | dbgp_ehci_status("ehci reset done"); | |
484 | return 0; | |
485 | } | |
486 | static int ehci_wait_for_port(int port); | |
487 | /* Return 0 on success | |
488 | * Return -ENODEV for any general failure | |
489 | * Return -EIO if wait for port fails | |
490 | */ | |
491 | int dbgp_external_startup(void) | |
492 | { | |
493 | int devnum; | |
494 | struct usb_debug_descriptor dbgp_desc; | |
495 | int ret; | |
aab2d408 | 496 | u32 ctrl, portsc, cmd; |
91777826 JW |
497 | int dbg_port = dbgp_phys_port; |
498 | int tries = 3; | |
aab2d408 JW |
499 | int reset_port_tries = 1; |
500 | int try_hard_once = 1; | |
91777826 | 501 | |
aab2d408 | 502 | try_port_reset_again: |
91777826 JW |
503 | ret = dbgp_ehci_startup(); |
504 | if (ret) | |
505 | return ret; | |
506 | ||
507 | /* Wait for a device to show up in the debug port */ | |
508 | ret = ehci_wait_for_port(dbg_port); | |
509 | if (ret < 0) { | |
510 | portsc = readl(&ehci_regs->port_status[dbg_port - 1]); | |
aab2d408 JW |
511 | if (!(portsc & PORT_CONNECT) && try_hard_once) { |
512 | /* Last ditch effort to try to force enable | |
513 | * the debug device by using the packet test | |
514 | * ehci command to try and wake it up. */ | |
515 | try_hard_once = 0; | |
516 | cmd = readl(&ehci_regs->command); | |
517 | cmd &= ~CMD_RUN; | |
518 | writel(cmd, &ehci_regs->command); | |
519 | portsc = readl(&ehci_regs->port_status[dbg_port - 1]); | |
520 | portsc |= PORT_TEST_PKT; | |
521 | writel(portsc, &ehci_regs->port_status[dbg_port - 1]); | |
522 | dbgp_ehci_status("Trying to force debug port online"); | |
523 | mdelay(50); | |
524 | dbgp_ehci_controller_reset(); | |
525 | goto try_port_reset_again; | |
526 | } else if (reset_port_tries--) { | |
527 | goto try_port_reset_again; | |
528 | } | |
91777826 JW |
529 | dbgp_printk("No device found in debug port\n"); |
530 | return -EIO; | |
531 | } | |
532 | dbgp_ehci_status("wait for port done"); | |
533 | ||
534 | /* Enable the debug port */ | |
535 | ctrl = readl(&ehci_debug->control); | |
536 | ctrl |= DBGP_CLAIM; | |
537 | writel(ctrl, &ehci_debug->control); | |
538 | ctrl = readl(&ehci_debug->control); | |
539 | if ((ctrl & DBGP_CLAIM) != DBGP_CLAIM) { | |
540 | dbgp_printk("No device in debug port\n"); | |
541 | writel(ctrl & ~DBGP_CLAIM, &ehci_debug->control); | |
542 | return -ENODEV; | |
543 | } | |
544 | dbgp_ehci_status("debug ported enabled"); | |
545 | ||
546 | /* Completely transfer the debug device to the debug controller */ | |
547 | portsc = readl(&ehci_regs->port_status[dbg_port - 1]); | |
548 | portsc &= ~PORT_PE; | |
549 | writel(portsc, &ehci_regs->port_status[dbg_port - 1]); | |
550 | ||
551 | dbgp_mdelay(100); | |
552 | ||
553 | try_again: | |
554 | /* Find the debug device and make it device number 127 */ | |
555 | for (devnum = 0; devnum <= 127; devnum++) { | |
556 | ret = dbgp_control_msg(devnum, | |
557 | USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE, | |
558 | USB_REQ_GET_DESCRIPTOR, (USB_DT_DEBUG << 8), 0, | |
559 | &dbgp_desc, sizeof(dbgp_desc)); | |
560 | if (ret > 0) | |
561 | break; | |
562 | } | |
563 | if (devnum > 127) { | |
564 | dbgp_printk("Could not find attached debug device\n"); | |
565 | goto err; | |
566 | } | |
567 | if (ret < 0) { | |
568 | dbgp_printk("Attached device is not a debug device\n"); | |
569 | goto err; | |
570 | } | |
571 | dbgp_endpoint_out = dbgp_desc.bDebugOutEndpoint; | |
4fe1da4e | 572 | dbgp_endpoint_in = dbgp_desc.bDebugInEndpoint; |
91777826 JW |
573 | |
574 | /* Move the device to 127 if it isn't already there */ | |
575 | if (devnum != USB_DEBUG_DEVNUM) { | |
576 | ret = dbgp_control_msg(devnum, | |
577 | USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE, | |
578 | USB_REQ_SET_ADDRESS, USB_DEBUG_DEVNUM, 0, NULL, 0); | |
579 | if (ret < 0) { | |
580 | dbgp_printk("Could not move attached device to %d\n", | |
581 | USB_DEBUG_DEVNUM); | |
582 | goto err; | |
583 | } | |
584 | devnum = USB_DEBUG_DEVNUM; | |
585 | dbgp_printk("debug device renamed to 127\n"); | |
586 | } | |
587 | ||
588 | /* Enable the debug interface */ | |
589 | ret = dbgp_control_msg(USB_DEBUG_DEVNUM, | |
590 | USB_DIR_OUT | USB_TYPE_STANDARD | USB_RECIP_DEVICE, | |
591 | USB_REQ_SET_FEATURE, USB_DEVICE_DEBUG_MODE, 0, NULL, 0); | |
592 | if (ret < 0) { | |
593 | dbgp_printk(" Could not enable the debug device\n"); | |
594 | goto err; | |
595 | } | |
596 | dbgp_printk("debug interface enabled\n"); | |
597 | /* Perform a small write to get the even/odd data state in sync | |
598 | */ | |
599 | ret = dbgp_bulk_write(USB_DEBUG_DEVNUM, dbgp_endpoint_out, " ", 1); | |
600 | if (ret < 0) { | |
601 | dbgp_printk("dbgp_bulk_write failed: %d\n", ret); | |
602 | goto err; | |
603 | } | |
ef58d97a | 604 | dbgp_printk("small write done\n"); |
91777826 JW |
605 | dbgp_not_safe = 0; |
606 | ||
607 | return 0; | |
608 | err: | |
609 | if (tries--) | |
610 | goto try_again; | |
611 | return -ENODEV; | |
612 | } | |
613 | EXPORT_SYMBOL_GPL(dbgp_external_startup); | |
614 | ||
40b52371 | 615 | static int ehci_reset_port(int port) |
df6c5169 JW |
616 | { |
617 | u32 portsc; | |
618 | u32 delay_time, delay; | |
619 | int loop; | |
620 | ||
91777826 | 621 | dbgp_ehci_status("reset port"); |
df6c5169 JW |
622 | /* Reset the usb debug port */ |
623 | portsc = readl(&ehci_regs->port_status[port - 1]); | |
624 | portsc &= ~PORT_PE; | |
625 | portsc |= PORT_RESET; | |
626 | writel(portsc, &ehci_regs->port_status[port - 1]); | |
627 | ||
628 | delay = HUB_ROOT_RESET_TIME; | |
629 | for (delay_time = 0; delay_time < HUB_RESET_TIMEOUT; | |
630 | delay_time += delay) { | |
631 | dbgp_mdelay(delay); | |
df6c5169 | 632 | portsc = readl(&ehci_regs->port_status[port - 1]); |
56faf0f9 JW |
633 | if (!(portsc & PORT_RESET)) |
634 | break; | |
635 | } | |
df6c5169 JW |
636 | if (portsc & PORT_RESET) { |
637 | /* force reset to complete */ | |
56faf0f9 | 638 | loop = 100 * 1000; |
df6c5169 JW |
639 | writel(portsc & ~(PORT_RWC_BITS | PORT_RESET), |
640 | &ehci_regs->port_status[port - 1]); | |
641 | do { | |
56faf0f9 | 642 | udelay(1); |
df6c5169 JW |
643 | portsc = readl(&ehci_regs->port_status[port-1]); |
644 | } while ((portsc & PORT_RESET) && (--loop > 0)); | |
645 | } | |
646 | ||
647 | /* Device went away? */ | |
648 | if (!(portsc & PORT_CONNECT)) | |
649 | return -ENOTCONN; | |
650 | ||
25985edc | 651 | /* bomb out completely if something weird happened */ |
df6c5169 JW |
652 | if ((portsc & PORT_CSC)) |
653 | return -EINVAL; | |
654 | ||
655 | /* If we've finished resetting, then break out of the loop */ | |
656 | if (!(portsc & PORT_RESET) && (portsc & PORT_PE)) | |
657 | return 0; | |
df6c5169 JW |
658 | return -EBUSY; |
659 | } | |
660 | ||
91777826 | 661 | static int ehci_wait_for_port(int port) |
df6c5169 JW |
662 | { |
663 | u32 status; | |
664 | int ret, reps; | |
665 | ||
56faf0f9 | 666 | for (reps = 0; reps < 300; reps++) { |
df6c5169 | 667 | status = readl(&ehci_regs->status); |
56faf0f9 JW |
668 | if (status & STS_PCD) |
669 | break; | |
670 | dbgp_mdelay(1); | |
df6c5169 | 671 | } |
56faf0f9 JW |
672 | ret = ehci_reset_port(port); |
673 | if (ret == 0) | |
674 | return 0; | |
df6c5169 JW |
675 | return -ENOTCONN; |
676 | } | |
677 | ||
df6c5169 JW |
678 | typedef void (*set_debug_port_t)(int port); |
679 | ||
680 | static void __init default_set_debug_port(int port) | |
681 | { | |
682 | } | |
683 | ||
684 | static set_debug_port_t __initdata set_debug_port = default_set_debug_port; | |
685 | ||
686 | static void __init nvidia_set_debug_port(int port) | |
687 | { | |
688 | u32 dword; | |
689 | dword = read_pci_config(ehci_dev.bus, ehci_dev.slot, ehci_dev.func, | |
690 | 0x74); | |
691 | dword &= ~(0x0f<<12); | |
692 | dword |= ((port & 0x0f)<<12); | |
693 | write_pci_config(ehci_dev.bus, ehci_dev.slot, ehci_dev.func, 0x74, | |
694 | dword); | |
695 | dbgp_printk("set debug port to %d\n", port); | |
696 | } | |
697 | ||
698 | static void __init detect_set_debug_port(void) | |
699 | { | |
700 | u32 vendorid; | |
701 | ||
702 | vendorid = read_pci_config(ehci_dev.bus, ehci_dev.slot, ehci_dev.func, | |
703 | 0x00); | |
704 | ||
705 | if ((vendorid & 0xffff) == 0x10de) { | |
706 | dbgp_printk("using nvidia set_debug_port\n"); | |
707 | set_debug_port = nvidia_set_debug_port; | |
708 | } | |
709 | } | |
710 | ||
093344e1 JW |
711 | /* The code in early_ehci_bios_handoff() is derived from the usb pci |
712 | * quirk initialization, but altered so as to use the early PCI | |
713 | * routines. */ | |
714 | #define EHCI_USBLEGSUP_BIOS (1 << 16) /* BIOS semaphore */ | |
715 | #define EHCI_USBLEGCTLSTS 4 /* legacy control/status */ | |
716 | static void __init early_ehci_bios_handoff(void) | |
717 | { | |
718 | u32 hcc_params = readl(&ehci_caps->hcc_params); | |
719 | int offset = (hcc_params >> 8) & 0xff; | |
720 | u32 cap; | |
721 | int msec; | |
722 | ||
723 | if (!offset) | |
724 | return; | |
725 | ||
726 | cap = read_pci_config(ehci_dev.bus, ehci_dev.slot, | |
727 | ehci_dev.func, offset); | |
728 | dbgp_printk("dbgp: ehci BIOS state %08x\n", cap); | |
729 | ||
730 | if ((cap & 0xff) == 1 && (cap & EHCI_USBLEGSUP_BIOS)) { | |
731 | dbgp_printk("dbgp: BIOS handoff\n"); | |
732 | write_pci_config_byte(ehci_dev.bus, ehci_dev.slot, | |
733 | ehci_dev.func, offset + 3, 1); | |
734 | } | |
735 | ||
736 | /* if boot firmware now owns EHCI, spin till it hands it over. */ | |
737 | msec = 1000; | |
738 | while ((cap & EHCI_USBLEGSUP_BIOS) && (msec > 0)) { | |
739 | mdelay(10); | |
740 | msec -= 10; | |
741 | cap = read_pci_config(ehci_dev.bus, ehci_dev.slot, | |
742 | ehci_dev.func, offset); | |
743 | } | |
744 | ||
745 | if (cap & EHCI_USBLEGSUP_BIOS) { | |
746 | /* well, possibly buggy BIOS... try to shut it down, | |
747 | * and hope nothing goes too wrong */ | |
748 | dbgp_printk("dbgp: BIOS handoff failed: %08x\n", cap); | |
749 | write_pci_config_byte(ehci_dev.bus, ehci_dev.slot, | |
750 | ehci_dev.func, offset + 2, 0); | |
751 | } | |
752 | ||
753 | /* just in case, always disable EHCI SMIs */ | |
754 | write_pci_config_byte(ehci_dev.bus, ehci_dev.slot, ehci_dev.func, | |
755 | offset + EHCI_USBLEGCTLSTS, 0); | |
756 | } | |
757 | ||
df6c5169 JW |
758 | static int __init ehci_setup(void) |
759 | { | |
91777826 | 760 | u32 ctrl, portsc, hcs_params; |
df6c5169 | 761 | u32 debug_port, new_debug_port = 0, n_ports; |
df6c5169 | 762 | int ret, i; |
df6c5169 JW |
763 | int port_map_tried; |
764 | int playtimes = 3; | |
765 | ||
093344e1 JW |
766 | early_ehci_bios_handoff(); |
767 | ||
df6c5169 JW |
768 | try_next_time: |
769 | port_map_tried = 0; | |
770 | ||
771 | try_next_port: | |
772 | ||
773 | hcs_params = readl(&ehci_caps->hcs_params); | |
774 | debug_port = HCS_DEBUG_PORT(hcs_params); | |
91777826 | 775 | dbgp_phys_port = debug_port; |
df6c5169 JW |
776 | n_ports = HCS_N_PORTS(hcs_params); |
777 | ||
778 | dbgp_printk("debug_port: %d\n", debug_port); | |
779 | dbgp_printk("n_ports: %d\n", n_ports); | |
91777826 | 780 | dbgp_ehci_status(""); |
df6c5169 JW |
781 | |
782 | for (i = 1; i <= n_ports; i++) { | |
783 | portsc = readl(&ehci_regs->port_status[i-1]); | |
784 | dbgp_printk("portstatus%d: %08x\n", i, portsc); | |
785 | } | |
786 | ||
787 | if (port_map_tried && (new_debug_port != debug_port)) { | |
788 | if (--playtimes) { | |
789 | set_debug_port(new_debug_port); | |
790 | goto try_next_time; | |
791 | } | |
792 | return -1; | |
793 | } | |
794 | ||
91777826 JW |
795 | /* Only reset the controller if it is not already in the |
796 | * configured state */ | |
797 | if (!(readl(&ehci_regs->configured_flag) & FLAG_CF)) { | |
798 | if (dbgp_ehci_controller_reset() != 0) | |
799 | return -1; | |
800 | } else { | |
801 | dbgp_ehci_status("ehci skip - already configured"); | |
df6c5169 | 802 | } |
df6c5169 | 803 | |
91777826 JW |
804 | ret = dbgp_external_startup(); |
805 | if (ret == -EIO) | |
df6c5169 | 806 | goto next_debug_port; |
df6c5169 | 807 | |
df6c5169 | 808 | if (ret < 0) { |
91777826 JW |
809 | /* Things didn't work so remove my claim */ |
810 | ctrl = readl(&ehci_debug->control); | |
811 | ctrl &= ~(DBGP_CLAIM | DBGP_OUT); | |
812 | writel(ctrl, &ehci_debug->control); | |
813 | return -1; | |
df6c5169 | 814 | } |
df6c5169 | 815 | return 0; |
df6c5169 JW |
816 | |
817 | next_debug_port: | |
818 | port_map_tried |= (1<<(debug_port - 1)); | |
819 | new_debug_port = ((debug_port-1+1)%n_ports) + 1; | |
820 | if (port_map_tried != ((1<<n_ports) - 1)) { | |
821 | set_debug_port(new_debug_port); | |
822 | goto try_next_port; | |
823 | } | |
824 | if (--playtimes) { | |
825 | set_debug_port(new_debug_port); | |
826 | goto try_next_time; | |
827 | } | |
828 | ||
829 | return -1; | |
830 | } | |
831 | ||
832 | int __init early_dbgp_init(char *s) | |
833 | { | |
834 | u32 debug_port, bar, offset; | |
835 | u32 bus, slot, func, cap; | |
836 | void __iomem *ehci_bar; | |
837 | u32 dbgp_num; | |
838 | u32 bar_val; | |
839 | char *e; | |
840 | int ret; | |
841 | u8 byte; | |
842 | ||
843 | if (!early_pci_allowed()) | |
844 | return -1; | |
845 | ||
846 | dbgp_num = 0; | |
847 | if (*s) | |
848 | dbgp_num = simple_strtoul(s, &e, 10); | |
849 | dbgp_printk("dbgp_num: %d\n", dbgp_num); | |
850 | ||
851 | cap = find_dbgp(dbgp_num, &bus, &slot, &func); | |
852 | if (!cap) | |
853 | return -1; | |
854 | ||
855 | dbgp_printk("Found EHCI debug port on %02x:%02x.%1x\n", bus, slot, | |
856 | func); | |
857 | ||
858 | debug_port = read_pci_config(bus, slot, func, cap); | |
859 | bar = (debug_port >> 29) & 0x7; | |
860 | bar = (bar * 4) + 0xc; | |
861 | offset = (debug_port >> 16) & 0xfff; | |
862 | dbgp_printk("bar: %02x offset: %03x\n", bar, offset); | |
863 | if (bar != PCI_BASE_ADDRESS_0) { | |
864 | dbgp_printk("only debug ports on bar 1 handled.\n"); | |
865 | ||
866 | return -1; | |
867 | } | |
868 | ||
869 | bar_val = read_pci_config(bus, slot, func, PCI_BASE_ADDRESS_0); | |
870 | dbgp_printk("bar_val: %02x offset: %03x\n", bar_val, offset); | |
871 | if (bar_val & ~PCI_BASE_ADDRESS_MEM_MASK) { | |
872 | dbgp_printk("only simple 32bit mmio bars supported\n"); | |
873 | ||
874 | return -1; | |
875 | } | |
876 | ||
877 | /* double check if the mem space is enabled */ | |
878 | byte = read_pci_config_byte(bus, slot, func, 0x04); | |
879 | if (!(byte & 0x2)) { | |
880 | byte |= 0x02; | |
881 | write_pci_config_byte(bus, slot, func, 0x04, byte); | |
882 | dbgp_printk("mmio for ehci enabled\n"); | |
883 | } | |
884 | ||
885 | /* | |
886 | * FIXME I don't have the bar size so just guess PAGE_SIZE is more | |
887 | * than enough. 1K is the biggest I have seen. | |
888 | */ | |
889 | set_fixmap_nocache(FIX_DBGP_BASE, bar_val & PAGE_MASK); | |
890 | ehci_bar = (void __iomem *)__fix_to_virt(FIX_DBGP_BASE); | |
891 | ehci_bar += bar_val & ~PAGE_MASK; | |
892 | dbgp_printk("ehci_bar: %p\n", ehci_bar); | |
893 | ||
894 | ehci_caps = ehci_bar; | |
895 | ehci_regs = ehci_bar + HC_LENGTH(readl(&ehci_caps->hc_capbase)); | |
896 | ehci_debug = ehci_bar + offset; | |
897 | ehci_dev.bus = bus; | |
898 | ehci_dev.slot = slot; | |
899 | ehci_dev.func = func; | |
900 | ||
901 | detect_set_debug_port(); | |
902 | ||
903 | ret = ehci_setup(); | |
904 | if (ret < 0) { | |
905 | dbgp_printk("ehci_setup failed\n"); | |
906 | ehci_debug = NULL; | |
907 | ||
908 | return -1; | |
909 | } | |
91777826 | 910 | dbgp_ehci_status("early_init_complete"); |
df6c5169 JW |
911 | |
912 | return 0; | |
913 | } | |
914 | ||
915 | static void early_dbgp_write(struct console *con, const char *str, u32 n) | |
916 | { | |
917 | int chunk, ret; | |
87a5d151 JW |
918 | char buf[DBGP_MAX_PACKET]; |
919 | int use_cr = 0; | |
91777826 JW |
920 | u32 cmd, ctrl; |
921 | int reset_run = 0; | |
df6c5169 | 922 | |
91777826 | 923 | if (!ehci_debug || dbgp_not_safe) |
df6c5169 | 924 | return; |
91777826 JW |
925 | |
926 | cmd = readl(&ehci_regs->command); | |
927 | if (unlikely(!(cmd & CMD_RUN))) { | |
928 | /* If the ehci controller is not in the run state do extended | |
929 | * checks to see if the acpi or some other initialization also | |
930 | * reset the ehci debug port */ | |
931 | ctrl = readl(&ehci_debug->control); | |
932 | if (!(ctrl & DBGP_ENABLED)) { | |
933 | dbgp_not_safe = 1; | |
934 | dbgp_external_startup(); | |
935 | } else { | |
936 | cmd |= CMD_RUN; | |
937 | writel(cmd, &ehci_regs->command); | |
938 | reset_run = 1; | |
939 | } | |
940 | } | |
df6c5169 | 941 | while (n > 0) { |
87a5d151 JW |
942 | for (chunk = 0; chunk < DBGP_MAX_PACKET && n > 0; |
943 | str++, chunk++, n--) { | |
944 | if (!use_cr && *str == '\n') { | |
945 | use_cr = 1; | |
946 | buf[chunk] = '\r'; | |
947 | str--; | |
948 | n++; | |
949 | continue; | |
950 | } | |
951 | if (use_cr) | |
952 | use_cr = 0; | |
953 | buf[chunk] = *str; | |
954 | } | |
91777826 JW |
955 | if (chunk > 0) { |
956 | ret = dbgp_bulk_write(USB_DEBUG_DEVNUM, | |
957 | dbgp_endpoint_out, buf, chunk); | |
958 | } | |
959 | } | |
960 | if (unlikely(reset_run)) { | |
961 | cmd = readl(&ehci_regs->command); | |
962 | cmd &= ~CMD_RUN; | |
963 | writel(cmd, &ehci_regs->command); | |
df6c5169 JW |
964 | } |
965 | } | |
966 | ||
967 | struct console early_dbgp_console = { | |
968 | .name = "earlydbg", | |
969 | .write = early_dbgp_write, | |
970 | .flags = CON_PRINTBUFFER, | |
971 | .index = -1, | |
972 | }; | |
8d053c79 JW |
973 | |
974 | int dbgp_reset_prep(void) | |
975 | { | |
976 | u32 ctrl; | |
977 | ||
978 | dbgp_not_safe = 1; | |
979 | if (!ehci_debug) | |
980 | return 0; | |
981 | ||
4fe1da4e JW |
982 | if ((early_dbgp_console.index != -1 && |
983 | !(early_dbgp_console.flags & CON_BOOT)) || | |
984 | dbgp_kgdb_mode) | |
8d053c79 JW |
985 | return 1; |
986 | /* This means the console is not initialized, or should get | |
987 | * shutdown so as to allow for reuse of the usb device, which | |
988 | * means it is time to shutdown the usb debug port. */ | |
989 | ctrl = readl(&ehci_debug->control); | |
990 | if (ctrl & DBGP_ENABLED) { | |
991 | ctrl &= ~(DBGP_CLAIM); | |
992 | writel(ctrl, &ehci_debug->control); | |
993 | } | |
994 | return 0; | |
995 | } | |
996 | EXPORT_SYMBOL_GPL(dbgp_reset_prep); | |
4fe1da4e JW |
997 | |
998 | #ifdef CONFIG_KGDB | |
999 | ||
1000 | static char kgdbdbgp_buf[DBGP_MAX_PACKET]; | |
1001 | static int kgdbdbgp_buf_sz; | |
1002 | static int kgdbdbgp_buf_idx; | |
1003 | static int kgdbdbgp_loop_cnt = DBGP_LOOPS; | |
1004 | ||
1005 | static int kgdbdbgp_read_char(void) | |
1006 | { | |
1007 | int ret; | |
1008 | ||
1009 | if (kgdbdbgp_buf_idx < kgdbdbgp_buf_sz) { | |
1010 | char ch = kgdbdbgp_buf[kgdbdbgp_buf_idx++]; | |
1011 | return ch; | |
1012 | } | |
1013 | ||
1014 | ret = dbgp_bulk_read(USB_DEBUG_DEVNUM, dbgp_endpoint_in, | |
1015 | &kgdbdbgp_buf, DBGP_MAX_PACKET, | |
1016 | kgdbdbgp_loop_cnt); | |
1017 | if (ret <= 0) | |
1018 | return NO_POLL_CHAR; | |
1019 | kgdbdbgp_buf_sz = ret; | |
1020 | kgdbdbgp_buf_idx = 1; | |
1021 | return kgdbdbgp_buf[0]; | |
1022 | } | |
1023 | ||
1024 | static void kgdbdbgp_write_char(u8 chr) | |
1025 | { | |
1026 | early_dbgp_write(NULL, &chr, 1); | |
1027 | } | |
1028 | ||
1029 | static struct kgdb_io kgdbdbgp_io_ops = { | |
1030 | .name = "kgdbdbgp", | |
1031 | .read_char = kgdbdbgp_read_char, | |
1032 | .write_char = kgdbdbgp_write_char, | |
1033 | }; | |
1034 | ||
1035 | static int kgdbdbgp_wait_time; | |
1036 | ||
1037 | static int __init kgdbdbgp_parse_config(char *str) | |
1038 | { | |
1039 | char *ptr; | |
1040 | ||
1041 | if (!ehci_debug) { | |
1042 | if (early_dbgp_init(str)) | |
1043 | return -1; | |
1044 | } | |
1045 | ptr = strchr(str, ','); | |
1046 | if (ptr) { | |
1047 | ptr++; | |
1048 | kgdbdbgp_wait_time = simple_strtoul(ptr, &ptr, 10); | |
1049 | } | |
1050 | kgdb_register_io_module(&kgdbdbgp_io_ops); | |
1051 | kgdbdbgp_io_ops.is_console = early_dbgp_console.index != -1; | |
1052 | ||
1053 | return 0; | |
1054 | } | |
1055 | early_param("kgdbdbgp", kgdbdbgp_parse_config); | |
1056 | ||
1057 | static int kgdbdbgp_reader_thread(void *ptr) | |
1058 | { | |
1059 | int ret; | |
1060 | ||
1061 | while (readl(&ehci_debug->control) & DBGP_ENABLED) { | |
1062 | kgdbdbgp_loop_cnt = 1; | |
1063 | ret = kgdbdbgp_read_char(); | |
1064 | kgdbdbgp_loop_cnt = DBGP_LOOPS; | |
1065 | if (ret != NO_POLL_CHAR) { | |
1066 | if (ret == 0x3 || ret == '$') { | |
1067 | if (ret == '$') | |
1068 | kgdbdbgp_buf_idx--; | |
1069 | kgdb_breakpoint(); | |
1070 | } | |
1071 | continue; | |
1072 | } | |
1073 | schedule_timeout_interruptible(kgdbdbgp_wait_time * HZ); | |
1074 | } | |
1075 | return 0; | |
1076 | } | |
1077 | ||
1078 | static int __init kgdbdbgp_start_thread(void) | |
1079 | { | |
1080 | if (dbgp_kgdb_mode && kgdbdbgp_wait_time) | |
1081 | kthread_run(kgdbdbgp_reader_thread, NULL, "%s", "dbgp"); | |
1082 | ||
1083 | return 0; | |
1084 | } | |
1085 | module_init(kgdbdbgp_start_thread); | |
1086 | #endif /* CONFIG_KGDB */ |