[linux-block.git] / drivers / thermal / Kconfig

# SPDX-License-Identifier: GPL-2.0-only
#
# Generic thermal sysfs drivers configuration
#

menuconfig THERMAL
	bool "Generic Thermal sysfs driver"
	help
	  Generic Thermal Sysfs driver offers a generic mechanism for
	  thermal management. Usually it's made up of one or more thermal
	  zone and cooling device.
	  Each thermal zone contains its own temperature, trip points,
	  cooling devices.
	  All platforms with ACPI thermal support can use this driver.
	  If you want this support, you should say Y here.

if THERMAL

config THERMAL_STATISTICS
	bool "Thermal state transition statistics"
	help
	  Export thermal state transition statistics information through sysfs.

	  If in doubt, say N.

config THERMAL_EMERGENCY_POWEROFF_DELAY_MS
	int "Emergency poweroff delay in milli-seconds"
	default 0
	help
	  Thermal subsystem will issue a graceful shutdown when
	  critical temperatures are reached using orderly_poweroff(). In
	  case of failure of an orderly_poweroff(), the thermal emergency
	  poweroff kicks in after a delay has elapsed and shuts down the system.
	  This config is number of milliseconds to delay before emergency
	  poweroff kicks in. Similarly to the critical trip point,
	  the delay should be carefully profiled so as to give adequate
	  time for orderly_poweroff() to finish on regular execution.
	  If set to 0 emergency poweroff will not be supported.

	  In doubt, leave as 0.

config THERMAL_HWMON
	bool
	prompt "Expose thermal sensors as hwmon device"
	depends on HWMON=y || HWMON=THERMAL
	default y
	help
	  In case a sensor is registered with the thermal
	  framework, this option will also register it
	  as a hwmon. The sensor will then have the common
	  hwmon sysfs interface.

	  Say 'Y' here if you want all thermal sensors to
	  have hwmon sysfs interface too.

config THERMAL_OF
	bool
	prompt "APIs to parse thermal data out of device tree"
	depends on OF
	default y
	help
	  This options provides helpers to add the support to
	  read and parse thermal data definitions out of the
	  device tree blob.

	  Say 'Y' here if you need to build thermal infrastructure
	  based on device tree.

config THERMAL_WRITABLE_TRIPS
	bool "Enable writable trip points"
	help
	  This option allows the system integrator to choose whether
	  trip temperatures can be changed from userspace. The
	  writable trips need to be specified when setting up the
	  thermal zone but the choice here takes precedence.

	  Say 'Y' here if you would like to allow userspace tools to
	  change trip temperatures.

choice
	prompt "Default Thermal governor"
	default THERMAL_DEFAULT_GOV_STEP_WISE
	help
	  This option sets which thermal governor shall be loaded at
	  startup. If in doubt, select 'step_wise'.

config THERMAL_DEFAULT_GOV_STEP_WISE
	bool "step_wise"
	select THERMAL_GOV_STEP_WISE
	help
	  Use the step_wise governor as default. This throttles the
	  devices one step at a time.

config THERMAL_DEFAULT_GOV_FAIR_SHARE
	bool "fair_share"
	select THERMAL_GOV_FAIR_SHARE
	help
	  Use the fair_share governor as default. This throttles the
	  devices based on their 'contribution' to a zone. The
	  contribution should be provided through platform data.

config THERMAL_DEFAULT_GOV_USER_SPACE
	bool "user_space"
	select THERMAL_GOV_USER_SPACE
	help
	  Select this if you want to let the user space manage the
	  platform thermals.

config THERMAL_DEFAULT_GOV_POWER_ALLOCATOR
	bool "power_allocator"
	depends on THERMAL_GOV_POWER_ALLOCATOR
	help
	  Select this if you want to control temperature based on
	  system and device power allocation. This governor can only
	  operate on cooling devices that implement the power API.

endchoice

config THERMAL_GOV_FAIR_SHARE
	bool "Fair-share thermal governor"
	help
	  Enable this to manage platform thermals using fair-share governor.

config THERMAL_GOV_STEP_WISE
	bool "Step_wise thermal governor"
	help
	  Enable this to manage platform thermals using a simple linear
	  governor.

config THERMAL_GOV_BANG_BANG
	bool "Bang Bang thermal governor"
	default n
	help
	  Enable this to manage platform thermals using bang bang governor.

	  Say 'Y' here if you want to use two point temperature regulation
	  used for fans without throttling.  Some fan drivers depend on this
	  governor to be enabled (e.g. acerhdf).

config THERMAL_GOV_USER_SPACE
	bool "User_space thermal governor"
	help
	  Enable this to let the user space manage the platform thermals.

config THERMAL_GOV_POWER_ALLOCATOR
	bool "Power allocator thermal governor"
	depends on ENERGY_MODEL
	help
	  Enable this to manage platform thermals by dynamically
	  allocating and limiting power to devices.

config CPU_THERMAL
	bool "Generic cpu cooling support"
	depends on CPU_FREQ
	depends on THERMAL_OF
	help
	  This implements the generic cpu cooling mechanism through frequency
	  reduction. An ACPI version of this already exists
	  (drivers/acpi/processor_thermal.c).
	  This will be useful for platforms using the generic thermal interface
	  and not the ACPI interface.

	  If you want this support, you should say Y here.

config CLOCK_THERMAL
	bool "Generic clock cooling support"
	depends on COMMON_CLK
	depends on PM_OPP
	help
	  This entry implements the generic clock cooling mechanism through
	  frequency clipping. Typically used to cool off co-processors. The
	  device that is configured to use this cooling mechanism will be
	  controlled to reduce clock frequency whenever temperature is high.

config DEVFREQ_THERMAL
	bool "Generic device cooling support"
	depends on PM_DEVFREQ
	depends on PM_OPP
	help
	  This implements the generic devfreq cooling mechanism through
	  frequency reduction for devices using devfreq.

	  This will throttle the device by limiting the maximum allowed DVFS
	  frequency corresponding to the cooling level.

	  In order to use the power extensions of the cooling device,
	  devfreq should use the simple_ondemand governor.

	  If you want this support, you should say Y here.

config THERMAL_EMULATION
	bool "Thermal emulation mode support"
	help
	  Enable this option to make a emul_temp sysfs node in thermal zone
	  directory to support temperature emulation. With emulation sysfs node,
	  user can manually input temperature and test the different trip
	  threshold behaviour for simulation purpose.

	  WARNING: Be careful while enabling this option on production systems,
	  because userland can easily disable the thermal policy by simply
	  flooding this sysfs node with low temperature values.

config THERMAL_MMIO
	tristate "Generic Thermal MMIO driver"
	depends on OF || COMPILE_TEST
	depends on HAS_IOMEM
	help
	  This option enables the generic thermal MMIO driver that will use
	  memory-mapped reads to get the temperature.  Any HW/System that
	  allows temperature reading by a single memory-mapped reading, be it
	  register or shared memory, is a potential candidate to work with this
	  driver.

config HISI_THERMAL
	tristate "Hisilicon thermal driver"
	depends on ARCH_HISI || COMPILE_TEST
	depends on HAS_IOMEM
	depends on OF
	default y
	help
	  Enable this to plug hisilicon's thermal sensor driver into the Linux
	  thermal framework. cpufreq is used as the cooling device to throttle
	  CPUs when the passive trip is crossed.

config IMX_THERMAL
	tristate "Temperature sensor driver for Freescale i.MX SoCs"
	depends on ARCH_MXC || COMPILE_TEST
	depends on NVMEM || !NVMEM
	depends on MFD_SYSCON
	depends on OF
	help
	  Support for Temperature Monitor (TEMPMON) found on Freescale i.MX SoCs.
	  It supports one critical trip point and one passive trip point.  The
	  cpufreq is used as the cooling device to throttle CPUs when the
	  passive trip is crossed.

config MAX77620_THERMAL
	tristate "Temperature sensor driver for Maxim MAX77620 PMIC"
	depends on MFD_MAX77620
	depends on OF
	help
	  Support for die junction temperature warning alarm for Maxim
	  Semiconductor PMIC MAX77620 device. Device generates two alarm
	  interrupts when PMIC die temperature cross the threshold of
	  120 degC and 140 degC.

config QORIQ_THERMAL
	tristate "QorIQ Thermal Monitoring Unit"
	depends on THERMAL_OF
	depends on HAS_IOMEM
	help
	  Support for Thermal Monitoring Unit (TMU) found on QorIQ platforms.
	  It supports one critical trip point and one passive trip point. The
	  cpufreq is used as the cooling device to throttle CPUs when the
	  passive trip is crossed.

config SPEAR_THERMAL
	tristate "SPEAr thermal sensor driver"
	depends on PLAT_SPEAR || COMPILE_TEST
	depends on HAS_IOMEM
	depends on OF
	help
	  Enable this to plug the SPEAr thermal sensor driver into the Linux
	  thermal framework.

config ROCKCHIP_THERMAL
	tristate "Rockchip thermal driver"
	depends on ARCH_ROCKCHIP || COMPILE_TEST
	depends on RESET_CONTROLLER
	depends on HAS_IOMEM
	help
	  Rockchip thermal driver provides support for Temperature sensor
	  ADC (TS-ADC) found on Rockchip SoCs. It supports one critical
	  trip point. Cpufreq is used as the cooling device and will throttle
	  CPUs when the Temperature crosses the passive trip point.

config RCAR_THERMAL
	tristate "Renesas R-Car thermal driver"
	depends on ARCH_RENESAS || COMPILE_TEST
	depends on HAS_IOMEM
	help
	  Enable this to plug the R-Car thermal sensor driver into the Linux
	  thermal framework.

config RCAR_GEN3_THERMAL
	tristate "Renesas R-Car Gen3 thermal driver"
	depends on ARCH_RENESAS || COMPILE_TEST
	depends on HAS_IOMEM
	depends on OF
	help
	  Enable this to plug the R-Car Gen3 thermal sensor driver into the Linux
	  thermal framework.

config KIRKWOOD_THERMAL
	tristate "Temperature sensor on Marvell Kirkwood SoCs"
	depends on MACH_KIRKWOOD || COMPILE_TEST
	depends on HAS_IOMEM
	depends on OF
	help
	  Support for the Kirkwood thermal sensor driver into the Linux thermal
	  framework. Only kirkwood 88F6282 and 88F6283 have this sensor.

config DOVE_THERMAL
	tristate "Temperature sensor on Marvell Dove SoCs"
	depends on ARCH_DOVE || MACH_DOVE || COMPILE_TEST
	depends on HAS_IOMEM
	depends on OF
	help
	  Support for the Dove thermal sensor driver in the Linux thermal
	  framework.

config DB8500_THERMAL
	tristate "DB8500 thermal management"
	depends on MFD_DB8500_PRCMU && OF
	default y
	help
	  Adds DB8500 thermal management implementation according to the thermal
	  management framework. A thermal zone with several trip points will be
	  created. Cooling devices can be bound to the trip points to cool this
	  thermal zone if trip points reached.

config ARMADA_THERMAL
	tristate "Marvell EBU Armada SoCs thermal management"
	depends on ARCH_MVEBU || COMPILE_TEST
	depends on HAS_IOMEM
	depends on OF
	help
	  Enable this option if you want to have support for thermal management
	  controller present in Marvell EBU Armada SoCs (370,375,XP,38x,7K,8K).

config DA9062_THERMAL
	tristate "DA9062/DA9061 Dialog Semiconductor thermal driver"
	depends on MFD_DA9062 || COMPILE_TEST
	depends on OF
	help
	  Enable this for the Dialog Semiconductor thermal sensor driver.
	  This will report PMIC junction over-temperature for one thermal trip
	  zone.
	  Compatible with the DA9062 and DA9061 PMICs.

config MTK_THERMAL
	tristate "Temperature sensor driver for mediatek SoCs"
	depends on ARCH_MEDIATEK || COMPILE_TEST
	depends on HAS_IOMEM
	depends on NVMEM || NVMEM=n
	depends on RESET_CONTROLLER
	default y
	help
	  Enable this option if you want to have support for thermal management
	  controller present in Mediatek SoCs

config AMLOGIC_THERMAL
	tristate "Amlogic Thermal Support"
	default ARCH_MESON
	depends on OF && ARCH_MESON
	help
	  If you say yes here you get support for Amlogic Thermal
	  for G12 SoC Family.

	  This driver can also be built as a module. If so, the module will
	  be called amlogic_thermal.

menu "Intel thermal drivers"
depends on X86 || X86_INTEL_QUARK || COMPILE_TEST
source "drivers/thermal/intel/Kconfig"
endmenu

menu "Broadcom thermal drivers"
depends on ARCH_BCM || ARCH_BRCMSTB || ARCH_BCM2835 || ARCH_BCM_IPROC || \
		COMPILE_TEST
source "drivers/thermal/broadcom/Kconfig"
endmenu

menu "Texas Instruments thermal drivers"
depends on ARCH_HAS_BANDGAP || COMPILE_TEST
depends on HAS_IOMEM
source "drivers/thermal/ti-soc-thermal/Kconfig"
endmenu

menu "Samsung thermal drivers"
depends on ARCH_EXYNOS || COMPILE_TEST
source "drivers/thermal/samsung/Kconfig"
endmenu

menu "STMicroelectronics thermal drivers"
depends on (ARCH_STI || ARCH_STM32) && OF
source "drivers/thermal/st/Kconfig"
endmenu

config TANGO_THERMAL
	tristate "Tango thermal management"
	depends on ARCH_TANGO || COMPILE_TEST
	help
	  Enable the Tango thermal driver, which supports the primitive
	  temperature sensor embedded in Tango chips since the SMP8758.
	  This sensor only generates a 1-bit signal to indicate whether
	  the die temperature exceeds a programmable threshold.

source "drivers/thermal/tegra/Kconfig"

config GENERIC_ADC_THERMAL
	tristate "Generic ADC based thermal sensor"
	depends on IIO
	help
	  This enabled a thermal sysfs driver for the temperature sensor
	  which is connected to the General Purpose ADC. The ADC channel
	  is read via IIO framework and the channel information is provided
	  to this driver. This driver reports the temperature by reading ADC
	  channel and converts it to temperature based on lookup table.

menu "Qualcomm thermal drivers"
depends on (ARCH_QCOM && OF) || COMPILE_TEST
source "drivers/thermal/qcom/Kconfig"
endmenu

config ZX2967_THERMAL
	tristate "Thermal sensors on zx2967 SoC"
	depends on ARCH_ZX || COMPILE_TEST
	help
	  Enable the zx2967 thermal sensors driver, which supports
	  the primitive temperature sensor embedded in zx2967 SoCs.
	  This sensor generates the real time die temperature.

config UNIPHIER_THERMAL
	tristate "Socionext UniPhier thermal driver"
	depends on ARCH_UNIPHIER || COMPILE_TEST
	depends on THERMAL_OF && MFD_SYSCON
	help
	  Enable this to plug in UniPhier on-chip PVT thermal driver into the
	  thermal framework. The driver supports CPU thermal zone temperature
	  reporting and a couple of trip points.
endif
Commit	Line	Data
ec8f24b7	1	# SPDX-License-Identifier: GPL-2.0-only
203d3d4a ZR	2	#
	3	# Generic thermal sysfs drivers configuration
	4	#
	5
	6	menuconfig THERMAL
554b3529	7	bool "Generic Thermal sysfs driver"
203d3d4a ZR	8	help
	9	Generic Thermal Sysfs driver offers a generic mechanism for
	10	thermal management. Usually it's made up of one or more thermal
	11	zone and cooling device.
543a9561	12	Each thermal zone contains its own temperature, trip points,
203d3d4a ZR	13	cooling devices.
203d3d4a ZR	14	All platforms with ACPI thermal support can use this driver.
554b3529	15	If you want this support, you should say Y here.
16d75239	16
72e19897 ZR	17	if THERMAL
72e19897 ZR	18
8ea22951 VK	19	config THERMAL_STATISTICS
	20	bool "Thermal state transition statistics"
	21	help
	22	Export thermal state transition statistics information through sysfs.
	23
	24	If in doubt, say N.
	25
ef1d87e0 K	26	config THERMAL_EMERGENCY_POWEROFF_DELAY_MS
ef1d87e0 K	27	int "Emergency poweroff delay in milli-seconds"
ef1d87e0 K	28	default 0
	29	help
	30	Thermal subsystem will issue a graceful shutdown when
	31	critical temperatures are reached using orderly_poweroff(). In
	32	case of failure of an orderly_poweroff(), the thermal emergency
	33	poweroff kicks in after a delay has elapsed and shuts down the system.
	34	This config is number of milliseconds to delay before emergency
	35	poweroff kicks in. Similarly to the critical trip point,
	36	the delay should be carefully profiled so as to give adequate
	37	time for orderly_poweroff() to finish on regular execution.
	38	If set to 0 emergency poweroff will not be supported.
	39
	40	In doubt, leave as 0.
	41
16d75239	42	config THERMAL_HWMON
ab92402a	43	bool
0dd88793	44	prompt "Expose thermal sensors as hwmon device"
16d75239	45	depends on HWMON=y \|\| HWMON=THERMAL
ab92402a	46	default y
0dd88793 EV	47	help
	48	In case a sensor is registered with the thermal
	49	framework, this option will also register it
	50	as a hwmon. The sensor will then have the common
	51	hwmon sysfs interface.
	52
	53	Say 'Y' here if you want all thermal sensors to
	54	have hwmon sysfs interface too.
6a92c366	55
4e5e4705 EV	56	config THERMAL_OF
	57	bool
	58	prompt "APIs to parse thermal data out of device tree"
	59	depends on OF
	60	default y
	61	help
	62	This options provides helpers to add the support to
	63	read and parse thermal data definitions out of the
	64	device tree blob.
	65
	66	Say 'Y' here if you need to build thermal infrastructure
	67	based on device tree.
	68
35e94644 PA	69	config THERMAL_WRITABLE_TRIPS
	70	bool "Enable writable trip points"
	71	help
	72	This option allows the system integrator to choose whether
	73	trip temperatures can be changed from userspace. The
	74	writable trips need to be specified when setting up the
	75	thermal zone but the choice here takes precedence.
	76
	77	Say 'Y' here if you would like to allow userspace tools to
	78	change trip temperatures.
	79
72e19897 ZR	80	choice
	81	prompt "Default Thermal governor"
	82	default THERMAL_DEFAULT_GOV_STEP_WISE
	83	help
	84	This option sets which thermal governor shall be loaded at
	85	startup. If in doubt, select 'step_wise'.
	86
	87	config THERMAL_DEFAULT_GOV_STEP_WISE
	88	bool "step_wise"
9d185d04	89	select THERMAL_GOV_STEP_WISE
72e19897 ZR	90	help
	91	Use the step_wise governor as default. This throttles the
	92	devices one step at a time.
	93
	94	config THERMAL_DEFAULT_GOV_FAIR_SHARE
	95	bool "fair_share"
9d185d04	96	select THERMAL_GOV_FAIR_SHARE
72e19897 ZR	97	help
	98	Use the fair_share governor as default. This throttles the
	99	devices based on their 'contribution' to a zone. The
	100	contribution should be provided through platform data.
	101
	102	config THERMAL_DEFAULT_GOV_USER_SPACE
	103	bool "user_space"
9d185d04	104	select THERMAL_GOV_USER_SPACE
72e19897 ZR	105	help
72e19897 ZR	106	Select this if you want to let the user space manage the
ece238fe	107	platform thermals.
72e19897	108
6b775e87 JM	109	config THERMAL_DEFAULT_GOV_POWER_ALLOCATOR
6b775e87 JM	110	bool "power_allocator"
50260614	111	depends on THERMAL_GOV_POWER_ALLOCATOR
6b775e87 JM	112	help
	113	Select this if you want to control temperature based on
	114	system and device power allocation. This governor can only
	115	operate on cooling devices that implement the power API.
	116
72e19897 ZR	117	endchoice
72e19897 ZR	118
9d185d04	119	config THERMAL_GOV_FAIR_SHARE
72e19897 ZR	120	bool "Fair-share thermal governor"
	121	help
	122	Enable this to manage platform thermals using fair-share governor.
	123
9d185d04	124	config THERMAL_GOV_STEP_WISE
72e19897 ZR	125	bool "Step_wise thermal governor"
	126	help
	127	Enable this to manage platform thermals using a simple linear
a8227948	128	governor.
72e19897	129
e4dbf98f PF	130	config THERMAL_GOV_BANG_BANG
	131	bool "Bang Bang thermal governor"
	132	default n
	133	help
	134	Enable this to manage platform thermals using bang bang governor.
	135
	136	Say 'Y' here if you want to use two point temperature regulation
	137	used for fans without throttling. Some fan drivers depend on this
	138	governor to be enabled (e.g. acerhdf).
	139
9d185d04	140	config THERMAL_GOV_USER_SPACE
72e19897 ZR	141	bool "User_space thermal governor"
	142	help
	143	Enable this to let the user space manage the platform thermals.
	144
6b775e87 JM	145	config THERMAL_GOV_POWER_ALLOCATOR
6b775e87 JM	146	bool "Power allocator thermal governor"
a4e893e8	147	depends on ENERGY_MODEL
6b775e87 JM	148	help
	149	Enable this to manage platform thermals by dynamically
	150	allocating and limiting power to devices.
	151
02361418	152	config CPU_THERMAL
2e31c856	153	bool "Generic cpu cooling support"
72e19897	154	depends on CPU_FREQ
39d99cff	155	depends on THERMAL_OF
02361418 ADK	156	help
02361418 ADK	157	This implements the generic cpu cooling mechanism through frequency
f7188b3d EV	158	reduction. An ACPI version of this already exists
f7188b3d EV	159	(drivers/acpi/processor_thermal.c).
02361418 ADK	160	This will be useful for platforms using the generic thermal interface
02361418 ADK	161	and not the ACPI interface.
f7188b3d	162
02361418 ADK	163	If you want this support, you should say Y here.
02361418 ADK	164
f9df89d8 EV	165	config CLOCK_THERMAL
	166	bool "Generic clock cooling support"
	167	depends on COMMON_CLK
	168	depends on PM_OPP
	169	help
	170	This entry implements the generic clock cooling mechanism through
	171	frequency clipping. Typically used to cool off co-processors. The
	172	device that is configured to use this cooling mechanism will be
	173	controlled to reduce clock frequency whenever temperature is high.
	174
a76caf55 ØE	175	config DEVFREQ_THERMAL
	176	bool "Generic device cooling support"
	177	depends on PM_DEVFREQ
	178	depends on PM_OPP
	179	help
	180	This implements the generic devfreq cooling mechanism through
	181	frequency reduction for devices using devfreq.
	182
	183	This will throttle the device by limiting the maximum allowed DVFS
	184	frequency corresponding to the cooling level.
	185
	186	In order to use the power extensions of the cooling device,
	187	devfreq should use the simple_ondemand governor.
	188
f9df89d8 EV	189	If you want this support, you should say Y here.
f9df89d8 EV	190
e6e238c3 ADK	191	config THERMAL_EMULATION
	192	bool "Thermal emulation mode support"
	193	help
	194	Enable this option to make a emul_temp sysfs node in thermal zone
	195	directory to support temperature emulation. With emulation sysfs node,
	196	user can manually input temperature and test the different trip
	197	threshold behaviour for simulation purpose.
	198
8837295a EV	199	WARNING: Be careful while enabling this option on production systems,
	200	because userland can easily disable the thermal policy by simply
	201	flooding this sysfs node with low temperature values.
	202
71aa3693 TS	203	config THERMAL_MMIO
	204	tristate "Generic Thermal MMIO driver"
	205	depends on OF \|\| COMPILE_TEST
6ec8070b	206	depends on HAS_IOMEM
71aa3693 TS	207	help
	208	This option enables the generic thermal MMIO driver that will use
	209	memory-mapped reads to get the temperature. Any HW/System that
	210	allows temperature reading by a single memory-mapped reading, be it
	211	register or shared memory, is a potential candidate to work with this
	212	driver.
	213
9a5238a9	214	config HISI_THERMAL
9a5238a9	215	tristate "Hisilicon thermal driver"
f05f4821	216	depends on ARCH_HISI \|\| COMPILE_TEST
bf82c350	217	depends on HAS_IOMEM
f05f4821 LY	218	depends on OF
f05f4821 LY	219	default y
9a5238a9	220	help
	221	Enable this to plug hisilicon's thermal sensor driver into the Linux
	222	thermal framework. cpufreq is used as the cooling device to throttle
	223	CPUs when the passive trip is crossed.
	224
ca3de46b SG	225	config IMX_THERMAL
ca3de46b SG	226	tristate "Temperature sensor driver for Freescale i.MX SoCs"
c589c566	227	depends on ARCH_MXC \|\| COMPILE_TEST
531fcdeb	228	depends on NVMEM \|\| !NVMEM
ca3de46b SG	229	depends on MFD_SYSCON
	230	depends on OF
	231	help
	232	Support for Temperature Monitor (TEMPMON) found on Freescale i.MX SoCs.
	233	It supports one critical trip point and one passive trip point. The
	234	cpufreq is used as the cooling device to throttle CPUs when the
	235	passive trip is crossed.
	236
ec4664b3 LD	237	config MAX77620_THERMAL
	238	tristate "Temperature sensor driver for Maxim MAX77620 PMIC"
	239	depends on MFD_MAX77620
	240	depends on OF
	241	help
	242	Support for die junction temperature warning alarm for Maxim
	243	Semiconductor PMIC MAX77620 device. Device generates two alarm
	244	interrupts when PMIC die temperature cross the threshold of
	245	120 degC and 140 degC.
	246
43528445 JH	247	config QORIQ_THERMAL
	248	tristate "QorIQ Thermal Monitoring Unit"
	249	depends on THERMAL_OF
	250	depends on HAS_IOMEM
	251	help
	252	Support for Thermal Monitoring Unit (TMU) found on QorIQ platforms.
	253	It supports one critical trip point and one passive trip point. The
	254	cpufreq is used as the cooling device to throttle CPUs when the
	255	passive trip is crossed.
	256
6a92c366	257	config SPEAR_THERMAL
4d2f1794	258	tristate "SPEAr thermal sensor driver"
aa2937b7	259	depends on PLAT_SPEAR \|\| COMPILE_TEST
bf82c350	260	depends on HAS_IOMEM
b9c7aff4	261	depends on OF
6a92c366 VF	262	help
6a92c366 VF	263	Enable this to plug the SPEAr thermal sensor driver into the Linux
a8227948	264	thermal framework.
1e426ffd	265
cbac8f63 CW	266	config ROCKCHIP_THERMAL
cbac8f63 CW	267	tristate "Rockchip thermal driver"
444f9b00	268	depends on ARCH_ROCKCHIP \|\| COMPILE_TEST
cbac8f63	269	depends on RESET_CONTROLLER
bf82c350	270	depends on HAS_IOMEM
cbac8f63 CW	271	help
	272	Rockchip thermal driver provides support for Temperature sensor
	273	ADC (TS-ADC) found on Rockchip SoCs. It supports one critical
	274	trip point. Cpufreq is used as the cooling device and will throttle
	275	CPUs when the Temperature crosses the passive trip point.
	276
1e426ffd KM	277	config RCAR_THERMAL
1e426ffd KM	278	tristate "Renesas R-Car thermal driver"
8255e4e2	279	depends on ARCH_RENESAS \|\| COMPILE_TEST
d1c8b041	280	depends on HAS_IOMEM
1e426ffd KM	281	help
1e426ffd KM	282	Enable this to plug the R-Car thermal sensor driver into the Linux
a8227948	283	thermal framework.
c48cbba6	284
564e73d2 WS	285	config RCAR_GEN3_THERMAL
	286	tristate "Renesas R-Car Gen3 thermal driver"
	287	depends on ARCH_RENESAS \|\| COMPILE_TEST
	288	depends on HAS_IOMEM
	289	depends on OF
	290	help
	291	Enable this to plug the R-Car Gen3 thermal sensor driver into the Linux
	292	thermal framework.
	293
7060aa36 NI	294	config KIRKWOOD_THERMAL
7060aa36 NI	295	tristate "Temperature sensor on Marvell Kirkwood SoCs"
9c8aa959	296	depends on MACH_KIRKWOOD \|\| COMPILE_TEST
bf82c350	297	depends on HAS_IOMEM
7060aa36 NI	298	depends on OF
	299	help
	300	Support for the Kirkwood thermal sensor driver into the Linux thermal
	301	framework. Only kirkwood 88F6282 and 88F6283 have this sensor.
	302
74ffa64c AL	303	config DOVE_THERMAL
74ffa64c AL	304	tristate "Temperature sensor on Marvell Dove SoCs"
07fffd5c	305	depends on ARCH_DOVE \|\| MACH_DOVE \|\| COMPILE_TEST
bf82c350	306	depends on HAS_IOMEM
74ffa64c AL	307	depends on OF
	308	help
	309	Support for the Dove thermal sensor driver in the Linux thermal
	310	framework.
	311
aa1acb04	312	config DB8500_THERMAL
26716ce1	313	tristate "DB8500 thermal management"
cb063a83	314	depends on MFD_DB8500_PRCMU && OF
aa1acb04	315	default y
	316	help
	317	Adds DB8500 thermal management implementation according to the thermal
	318	management framework. A thermal zone with several trip points will be
	319	created. Cooling devices can be bound to the trip points to cool this
	320	thermal zone if trip points reached.
	321
fa0d654c	322	config ARMADA_THERMAL
a9d58a1a	323	tristate "Marvell EBU Armada SoCs thermal management"
1b158267	324	depends on ARCH_MVEBU \|\| COMPILE_TEST
bf82c350	325	depends on HAS_IOMEM
fa0d654c EG	326	depends on OF
	327	help
	328	Enable this option if you want to have support for thermal management
a9d58a1a	329	controller present in Marvell EBU Armada SoCs (370,375,XP,38x,7K,8K).
fa0d654c	330
608567aa ST	331	config DA9062_THERMAL
	332	tristate "DA9062/DA9061 Dialog Semiconductor thermal driver"
	333	depends on MFD_DA9062 \|\| COMPILE_TEST
	334	depends on OF
	335	help
	336	Enable this for the Dialog Semiconductor thermal sensor driver.
	337	This will report PMIC junction over-temperature for one thermal trip
	338	zone.
	339	Compatible with the DA9062 and DA9061 PMICs.
	340
a92db1c8 SH	341	config MTK_THERMAL
	342	tristate "Temperature sensor driver for mediatek SoCs"
	343	depends on ARCH_MEDIATEK \|\| COMPILE_TEST
74e5053c	344	depends on HAS_IOMEM
62e14f6f	345	depends on NVMEM \|\| NVMEM=n
a6f4850d	346	depends on RESET_CONTROLLER
a92db1c8 SH	347	default y
	348	help
	349	Enable this option if you want to have support for thermal management
	350	controller present in Mediatek SoCs
	351
421eda10 GLR	352	config AMLOGIC_THERMAL
	353	tristate "Amlogic Thermal Support"
	354	default ARCH_MESON
	355	depends on OF && ARCH_MESON
	356	help
	357	If you say yes here you get support for Amlogic Thermal
	358	for G12 SoC Family.
	359
	360	This driver can also be built as a module. If so, the module will
	361	be called amlogic_thermal.
	362
3e8c4d31 AK	363	menu "Intel thermal drivers"
	364	depends on X86 \|\| X86_INTEL_QUARK \|\| COMPILE_TEST
	365	source "drivers/thermal/intel/Kconfig"
	366	endmenu
	367
a94cb7ee	368	menu "Broadcom thermal drivers"
250e2110 PK	369	depends on ARCH_BCM \|\| ARCH_BRCMSTB \|\| ARCH_BCM2835 \|\| ARCH_BCM_IPROC \|\| \
250e2110 PK	370	COMPILE_TEST
a94cb7ee RM	371	source "drivers/thermal/broadcom/Kconfig"
	372	endmenu
	373
eb982001	374	menu "Texas Instruments thermal drivers"
ec2feb47	375	depends on ARCH_HAS_BANDGAP \|\| COMPILE_TEST
bf82c350	376	depends on HAS_IOMEM
eb982001 EV	377	source "drivers/thermal/ti-soc-thermal/Kconfig"
eb982001 EV	378	endmenu
f157f596	379
c6821378	380	menu "Samsung thermal drivers"
2bf42735	381	depends on ARCH_EXYNOS \|\| COMPILE_TEST
c6821378 ADK	382	source "drivers/thermal/samsung/Kconfig"
	383	endmenu
	384
60aef7ce	385	menu "STMicroelectronics thermal drivers"
1d693155	386	depends on (ARCH_STI \|\| ARCH_STM32) && OF
60aef7ce LJ	387	source "drivers/thermal/st/Kconfig"
	388	endmenu
	389
0b58c08b MG	390	config TANGO_THERMAL
	391	tristate "Tango thermal management"
	392	depends on ARCH_TANGO \|\| COMPILE_TEST
	393	help
	394	Enable the Tango thermal driver, which supports the primitive
	395	temperature sensor embedded in Tango chips since the SMP8758.
	396	This sensor only generates a 1-bit signal to indicate whether
	397	the die temperature exceeds a programmable threshold.
	398
a4dff94f WN	399	source "drivers/thermal/tegra/Kconfig"
a4dff94f WN	400
b3aef78f LD	401	config GENERIC_ADC_THERMAL
	402	tristate "Generic ADC based thermal sensor"
	403	depends on IIO
	404	help
	405	This enabled a thermal sysfs driver for the temperature sensor
	406	which is connected to the General Purpose ADC. The ADC channel
	407	is read via IIO framework and the channel information is provided
	408	to this driver. This driver reports the temperature by reading ADC
	409	channel and converts it to temperature based on lookup table.
	410
9066073c RN	411	menu "Qualcomm thermal drivers"
	412	depends on (ARCH_QCOM && OF) \|\| COMPILE_TEST
	413	source "drivers/thermal/qcom/Kconfig"
	414	endmenu
	415
50fdd36f BX	416	config ZX2967_THERMAL
	417	tristate "Thermal sensors on zx2967 SoC"
	418	depends on ARCH_ZX \|\| COMPILE_TEST
	419	help
	420	Enable the zx2967 thermal sensors driver, which supports
	421	the primitive temperature sensor embedded in zx2967 SoCs.
	422	This sensor generates the real time die temperature.
	423
86da4391 KH	424	config UNIPHIER_THERMAL
	425	tristate "Socionext UniPhier thermal driver"
	426	depends on ARCH_UNIPHIER \|\| COMPILE_TEST
	427	depends on THERMAL_OF && MFD_SYSCON
	428	help
	429	Enable this to plug in UniPhier on-chip PVT thermal driver into the
	430	thermal framework. The driver supports CPU thermal zone temperature
	431	reporting and a couple of trip points.
72e19897	432	endif