Commit | Line | Data |
---|---|---|
ae918c02 AK |
1 | /* |
2 | * xilinx_spi.c | |
3 | * | |
4 | * Xilinx SPI controller driver (master mode only) | |
5 | * | |
6 | * Author: MontaVista Software, Inc. | |
7 | * source@mvista.com | |
8 | * | |
9 | * 2002-2007 (c) MontaVista Software, Inc. This file is licensed under the | |
10 | * terms of the GNU General Public License version 2. This program is licensed | |
11 | * "as is" without any warranty of any kind, whether express or implied. | |
12 | */ | |
13 | ||
14 | #include <linux/module.h> | |
15 | #include <linux/init.h> | |
16 | #include <linux/interrupt.h> | |
17 | #include <linux/platform_device.h> | |
18 | #include <linux/spi/spi.h> | |
19 | #include <linux/spi/spi_bitbang.h> | |
20 | #include <linux/io.h> | |
21 | ||
22 | #include <syslib/virtex_devices.h> | |
23 | ||
24 | #define XILINX_SPI_NAME "xspi" | |
25 | ||
26 | /* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e) | |
27 | * Product Specification", DS464 | |
28 | */ | |
29 | #define XSPI_CR_OFFSET 0x62 /* 16-bit Control Register */ | |
30 | ||
31 | #define XSPI_CR_ENABLE 0x02 | |
32 | #define XSPI_CR_MASTER_MODE 0x04 | |
33 | #define XSPI_CR_CPOL 0x08 | |
34 | #define XSPI_CR_CPHA 0x10 | |
35 | #define XSPI_CR_MODE_MASK (XSPI_CR_CPHA | XSPI_CR_CPOL) | |
36 | #define XSPI_CR_TXFIFO_RESET 0x20 | |
37 | #define XSPI_CR_RXFIFO_RESET 0x40 | |
38 | #define XSPI_CR_MANUAL_SSELECT 0x80 | |
39 | #define XSPI_CR_TRANS_INHIBIT 0x100 | |
40 | ||
41 | #define XSPI_SR_OFFSET 0x67 /* 8-bit Status Register */ | |
42 | ||
43 | #define XSPI_SR_RX_EMPTY_MASK 0x01 /* Receive FIFO is empty */ | |
44 | #define XSPI_SR_RX_FULL_MASK 0x02 /* Receive FIFO is full */ | |
45 | #define XSPI_SR_TX_EMPTY_MASK 0x04 /* Transmit FIFO is empty */ | |
46 | #define XSPI_SR_TX_FULL_MASK 0x08 /* Transmit FIFO is full */ | |
47 | #define XSPI_SR_MODE_FAULT_MASK 0x10 /* Mode fault error */ | |
48 | ||
49 | #define XSPI_TXD_OFFSET 0x6b /* 8-bit Data Transmit Register */ | |
50 | #define XSPI_RXD_OFFSET 0x6f /* 8-bit Data Receive Register */ | |
51 | ||
52 | #define XSPI_SSR_OFFSET 0x70 /* 32-bit Slave Select Register */ | |
53 | ||
54 | /* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414 | |
55 | * IPIF registers are 32 bit | |
56 | */ | |
57 | #define XIPIF_V123B_DGIER_OFFSET 0x1c /* IPIF global int enable reg */ | |
58 | #define XIPIF_V123B_GINTR_ENABLE 0x80000000 | |
59 | ||
60 | #define XIPIF_V123B_IISR_OFFSET 0x20 /* IPIF interrupt status reg */ | |
61 | #define XIPIF_V123B_IIER_OFFSET 0x28 /* IPIF interrupt enable reg */ | |
62 | ||
63 | #define XSPI_INTR_MODE_FAULT 0x01 /* Mode fault error */ | |
64 | #define XSPI_INTR_SLAVE_MODE_FAULT 0x02 /* Selected as slave while | |
65 | * disabled */ | |
66 | #define XSPI_INTR_TX_EMPTY 0x04 /* TxFIFO is empty */ | |
67 | #define XSPI_INTR_TX_UNDERRUN 0x08 /* TxFIFO was underrun */ | |
68 | #define XSPI_INTR_RX_FULL 0x10 /* RxFIFO is full */ | |
69 | #define XSPI_INTR_RX_OVERRUN 0x20 /* RxFIFO was overrun */ | |
70 | ||
71 | #define XIPIF_V123B_RESETR_OFFSET 0x40 /* IPIF reset register */ | |
72 | #define XIPIF_V123B_RESET_MASK 0x0a /* the value to write */ | |
73 | ||
74 | struct xilinx_spi { | |
75 | /* bitbang has to be first */ | |
76 | struct spi_bitbang bitbang; | |
77 | struct completion done; | |
78 | ||
79 | void __iomem *regs; /* virt. address of the control registers */ | |
80 | ||
81 | u32 irq; | |
82 | ||
83 | u32 speed_hz; /* SCK has a fixed frequency of speed_hz Hz */ | |
84 | ||
85 | u8 *rx_ptr; /* pointer in the Tx buffer */ | |
86 | const u8 *tx_ptr; /* pointer in the Rx buffer */ | |
87 | int remaining_bytes; /* the number of bytes left to transfer */ | |
88 | }; | |
89 | ||
90 | static void xspi_init_hw(void __iomem *regs_base) | |
91 | { | |
92 | /* Reset the SPI device */ | |
93 | out_be32(regs_base + XIPIF_V123B_RESETR_OFFSET, | |
94 | XIPIF_V123B_RESET_MASK); | |
95 | /* Disable all the interrupts just in case */ | |
96 | out_be32(regs_base + XIPIF_V123B_IIER_OFFSET, 0); | |
97 | /* Enable the global IPIF interrupt */ | |
98 | out_be32(regs_base + XIPIF_V123B_DGIER_OFFSET, | |
99 | XIPIF_V123B_GINTR_ENABLE); | |
100 | /* Deselect the slave on the SPI bus */ | |
101 | out_be32(regs_base + XSPI_SSR_OFFSET, 0xffff); | |
102 | /* Disable the transmitter, enable Manual Slave Select Assertion, | |
103 | * put SPI controller into master mode, and enable it */ | |
104 | out_be16(regs_base + XSPI_CR_OFFSET, | |
105 | XSPI_CR_TRANS_INHIBIT | XSPI_CR_MANUAL_SSELECT | |
106 | | XSPI_CR_MASTER_MODE | XSPI_CR_ENABLE); | |
107 | } | |
108 | ||
109 | static void xilinx_spi_chipselect(struct spi_device *spi, int is_on) | |
110 | { | |
111 | struct xilinx_spi *xspi = spi_master_get_devdata(spi->master); | |
112 | ||
113 | if (is_on == BITBANG_CS_INACTIVE) { | |
114 | /* Deselect the slave on the SPI bus */ | |
115 | out_be32(xspi->regs + XSPI_SSR_OFFSET, 0xffff); | |
116 | } else if (is_on == BITBANG_CS_ACTIVE) { | |
117 | /* Set the SPI clock phase and polarity */ | |
118 | u16 cr = in_be16(xspi->regs + XSPI_CR_OFFSET) | |
119 | & ~XSPI_CR_MODE_MASK; | |
120 | if (spi->mode & SPI_CPHA) | |
121 | cr |= XSPI_CR_CPHA; | |
122 | if (spi->mode & SPI_CPOL) | |
123 | cr |= XSPI_CR_CPOL; | |
124 | out_be16(xspi->regs + XSPI_CR_OFFSET, cr); | |
125 | ||
126 | /* We do not check spi->max_speed_hz here as the SPI clock | |
127 | * frequency is not software programmable (the IP block design | |
128 | * parameter) | |
129 | */ | |
130 | ||
131 | /* Activate the chip select */ | |
132 | out_be32(xspi->regs + XSPI_SSR_OFFSET, | |
133 | ~(0x0001 << spi->chip_select)); | |
134 | } | |
135 | } | |
136 | ||
137 | /* spi_bitbang requires custom setup_transfer() to be defined if there is a | |
138 | * custom txrx_bufs(). We have nothing to setup here as the SPI IP block | |
139 | * supports just 8 bits per word, and SPI clock can't be changed in software. | |
140 | * Check for 8 bits per word. Chip select delay calculations could be | |
141 | * added here as soon as bitbang_work() can be made aware of the delay value. | |
142 | */ | |
143 | static int xilinx_spi_setup_transfer(struct spi_device *spi, | |
144 | struct spi_transfer *t) | |
145 | { | |
146 | u8 bits_per_word; | |
147 | u32 hz; | |
148 | struct xilinx_spi *xspi = spi_master_get_devdata(spi->master); | |
149 | ||
150 | bits_per_word = (t) ? t->bits_per_word : spi->bits_per_word; | |
151 | hz = (t) ? t->speed_hz : spi->max_speed_hz; | |
152 | if (bits_per_word != 8) { | |
153 | dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n", | |
154 | __FUNCTION__, bits_per_word); | |
155 | return -EINVAL; | |
156 | } | |
157 | ||
158 | if (hz && xspi->speed_hz > hz) { | |
159 | dev_err(&spi->dev, "%s, unsupported clock rate %uHz\n", | |
160 | __FUNCTION__, hz); | |
161 | return -EINVAL; | |
162 | } | |
163 | ||
164 | return 0; | |
165 | } | |
166 | ||
167 | /* the spi->mode bits understood by this driver: */ | |
168 | #define MODEBITS (SPI_CPOL | SPI_CPHA) | |
169 | ||
170 | static int xilinx_spi_setup(struct spi_device *spi) | |
171 | { | |
172 | struct spi_bitbang *bitbang; | |
173 | struct xilinx_spi *xspi; | |
174 | int retval; | |
175 | ||
176 | xspi = spi_master_get_devdata(spi->master); | |
177 | bitbang = &xspi->bitbang; | |
178 | ||
179 | if (!spi->bits_per_word) | |
180 | spi->bits_per_word = 8; | |
181 | ||
182 | if (spi->mode & ~MODEBITS) { | |
183 | dev_err(&spi->dev, "%s, unsupported mode bits %x\n", | |
184 | __FUNCTION__, spi->mode & ~MODEBITS); | |
185 | return -EINVAL; | |
186 | } | |
187 | ||
188 | retval = xilinx_spi_setup_transfer(spi, NULL); | |
189 | if (retval < 0) | |
190 | return retval; | |
191 | ||
192 | dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n", | |
193 | __FUNCTION__, spi->mode & MODEBITS, spi->bits_per_word, 0); | |
194 | ||
195 | return 0; | |
196 | } | |
197 | ||
198 | static void xilinx_spi_fill_tx_fifo(struct xilinx_spi *xspi) | |
199 | { | |
200 | u8 sr; | |
201 | ||
202 | /* Fill the Tx FIFO with as many bytes as possible */ | |
203 | sr = in_8(xspi->regs + XSPI_SR_OFFSET); | |
204 | while ((sr & XSPI_SR_TX_FULL_MASK) == 0 && xspi->remaining_bytes > 0) { | |
205 | if (xspi->tx_ptr) { | |
206 | out_8(xspi->regs + XSPI_TXD_OFFSET, *xspi->tx_ptr++); | |
207 | } else { | |
208 | out_8(xspi->regs + XSPI_TXD_OFFSET, 0); | |
209 | } | |
210 | xspi->remaining_bytes--; | |
211 | sr = in_8(xspi->regs + XSPI_SR_OFFSET); | |
212 | } | |
213 | } | |
214 | ||
215 | static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t) | |
216 | { | |
217 | struct xilinx_spi *xspi = spi_master_get_devdata(spi->master); | |
218 | u32 ipif_ier; | |
219 | u16 cr; | |
220 | ||
221 | /* We get here with transmitter inhibited */ | |
222 | ||
223 | xspi->tx_ptr = t->tx_buf; | |
224 | xspi->rx_ptr = t->rx_buf; | |
225 | xspi->remaining_bytes = t->len; | |
226 | INIT_COMPLETION(xspi->done); | |
227 | ||
228 | xilinx_spi_fill_tx_fifo(xspi); | |
229 | ||
230 | /* Enable the transmit empty interrupt, which we use to determine | |
231 | * progress on the transmission. | |
232 | */ | |
233 | ipif_ier = in_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET); | |
234 | out_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET, | |
235 | ipif_ier | XSPI_INTR_TX_EMPTY); | |
236 | ||
237 | /* Start the transfer by not inhibiting the transmitter any longer */ | |
238 | cr = in_be16(xspi->regs + XSPI_CR_OFFSET) & ~XSPI_CR_TRANS_INHIBIT; | |
239 | out_be16(xspi->regs + XSPI_CR_OFFSET, cr); | |
240 | ||
241 | wait_for_completion(&xspi->done); | |
242 | ||
243 | /* Disable the transmit empty interrupt */ | |
244 | out_be32(xspi->regs + XIPIF_V123B_IIER_OFFSET, ipif_ier); | |
245 | ||
246 | return t->len - xspi->remaining_bytes; | |
247 | } | |
248 | ||
249 | ||
250 | /* This driver supports single master mode only. Hence Tx FIFO Empty | |
251 | * is the only interrupt we care about. | |
252 | * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode | |
253 | * Fault are not to happen. | |
254 | */ | |
255 | static irqreturn_t xilinx_spi_irq(int irq, void *dev_id) | |
256 | { | |
257 | struct xilinx_spi *xspi = dev_id; | |
258 | u32 ipif_isr; | |
259 | ||
260 | /* Get the IPIF interrupts, and clear them immediately */ | |
261 | ipif_isr = in_be32(xspi->regs + XIPIF_V123B_IISR_OFFSET); | |
262 | out_be32(xspi->regs + XIPIF_V123B_IISR_OFFSET, ipif_isr); | |
263 | ||
264 | if (ipif_isr & XSPI_INTR_TX_EMPTY) { /* Transmission completed */ | |
265 | u16 cr; | |
266 | u8 sr; | |
267 | ||
268 | /* A transmit has just completed. Process received data and | |
269 | * check for more data to transmit. Always inhibit the | |
270 | * transmitter while the Isr refills the transmit register/FIFO, | |
271 | * or make sure it is stopped if we're done. | |
272 | */ | |
273 | cr = in_be16(xspi->regs + XSPI_CR_OFFSET); | |
274 | out_be16(xspi->regs + XSPI_CR_OFFSET, | |
275 | cr | XSPI_CR_TRANS_INHIBIT); | |
276 | ||
277 | /* Read out all the data from the Rx FIFO */ | |
278 | sr = in_8(xspi->regs + XSPI_SR_OFFSET); | |
279 | while ((sr & XSPI_SR_RX_EMPTY_MASK) == 0) { | |
280 | u8 data; | |
281 | ||
282 | data = in_8(xspi->regs + XSPI_RXD_OFFSET); | |
283 | if (xspi->rx_ptr) { | |
284 | *xspi->rx_ptr++ = data; | |
285 | } | |
286 | sr = in_8(xspi->regs + XSPI_SR_OFFSET); | |
287 | } | |
288 | ||
289 | /* See if there is more data to send */ | |
290 | if (xspi->remaining_bytes > 0) { | |
291 | xilinx_spi_fill_tx_fifo(xspi); | |
292 | /* Start the transfer by not inhibiting the | |
293 | * transmitter any longer | |
294 | */ | |
295 | out_be16(xspi->regs + XSPI_CR_OFFSET, cr); | |
296 | } else { | |
297 | /* No more data to send. | |
298 | * Indicate the transfer is completed. | |
299 | */ | |
300 | complete(&xspi->done); | |
301 | } | |
302 | } | |
303 | ||
304 | return IRQ_HANDLED; | |
305 | } | |
306 | ||
307 | static int __init xilinx_spi_probe(struct platform_device *dev) | |
308 | { | |
309 | int ret = 0; | |
310 | struct spi_master *master; | |
311 | struct xilinx_spi *xspi; | |
312 | struct xspi_platform_data *pdata; | |
313 | struct resource *r; | |
314 | ||
315 | /* Get resources(memory, IRQ) associated with the device */ | |
316 | master = spi_alloc_master(&dev->dev, sizeof(struct xilinx_spi)); | |
317 | ||
318 | if (master == NULL) { | |
319 | return -ENOMEM; | |
320 | } | |
321 | ||
322 | platform_set_drvdata(dev, master); | |
323 | pdata = dev->dev.platform_data; | |
324 | ||
325 | if (pdata == NULL) { | |
326 | ret = -ENODEV; | |
327 | goto put_master; | |
328 | } | |
329 | ||
330 | r = platform_get_resource(dev, IORESOURCE_MEM, 0); | |
331 | if (r == NULL) { | |
332 | ret = -ENODEV; | |
333 | goto put_master; | |
334 | } | |
335 | ||
336 | xspi = spi_master_get_devdata(master); | |
337 | xspi->bitbang.master = spi_master_get(master); | |
338 | xspi->bitbang.chipselect = xilinx_spi_chipselect; | |
339 | xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer; | |
340 | xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs; | |
341 | xspi->bitbang.master->setup = xilinx_spi_setup; | |
342 | init_completion(&xspi->done); | |
343 | ||
344 | if (!request_mem_region(r->start, | |
345 | r->end - r->start + 1, XILINX_SPI_NAME)) { | |
346 | ret = -ENXIO; | |
347 | goto put_master; | |
348 | } | |
349 | ||
350 | xspi->regs = ioremap(r->start, r->end - r->start + 1); | |
351 | if (xspi->regs == NULL) { | |
352 | ret = -ENOMEM; | |
353 | goto put_master; | |
354 | } | |
355 | ||
356 | xspi->irq = platform_get_irq(dev, 0); | |
357 | if (xspi->irq < 0) { | |
358 | ret = -ENXIO; | |
359 | goto unmap_io; | |
360 | } | |
361 | ||
362 | master->bus_num = pdata->bus_num; | |
363 | master->num_chipselect = pdata->num_chipselect; | |
364 | xspi->speed_hz = pdata->speed_hz; | |
365 | ||
366 | /* SPI controller initializations */ | |
367 | xspi_init_hw(xspi->regs); | |
368 | ||
369 | /* Register for SPI Interrupt */ | |
370 | ret = request_irq(xspi->irq, xilinx_spi_irq, 0, XILINX_SPI_NAME, xspi); | |
371 | if (ret != 0) | |
372 | goto unmap_io; | |
373 | ||
374 | ret = spi_bitbang_start(&xspi->bitbang); | |
375 | if (ret != 0) { | |
376 | dev_err(&dev->dev, "spi_bitbang_start FAILED\n"); | |
377 | goto free_irq; | |
378 | } | |
379 | ||
380 | dev_info(&dev->dev, "at 0x%08X mapped to 0x%08X, irq=%d\n", | |
381 | r->start, (u32)xspi->regs, xspi->irq); | |
382 | ||
383 | return ret; | |
384 | ||
385 | free_irq: | |
386 | free_irq(xspi->irq, xspi); | |
387 | unmap_io: | |
388 | iounmap(xspi->regs); | |
389 | put_master: | |
390 | spi_master_put(master); | |
391 | return ret; | |
392 | } | |
393 | ||
394 | static int __devexit xilinx_spi_remove(struct platform_device *dev) | |
395 | { | |
396 | struct xilinx_spi *xspi; | |
397 | struct spi_master *master; | |
398 | ||
399 | master = platform_get_drvdata(dev); | |
400 | xspi = spi_master_get_devdata(master); | |
401 | ||
402 | spi_bitbang_stop(&xspi->bitbang); | |
403 | free_irq(xspi->irq, xspi); | |
404 | iounmap(xspi->regs); | |
405 | platform_set_drvdata(dev, 0); | |
406 | spi_master_put(xspi->bitbang.master); | |
407 | ||
408 | return 0; | |
409 | } | |
410 | ||
411 | static struct platform_driver xilinx_spi_driver = { | |
412 | .probe = xilinx_spi_probe, | |
413 | .remove = __devexit_p(xilinx_spi_remove), | |
414 | .driver = { | |
415 | .name = XILINX_SPI_NAME, | |
416 | .owner = THIS_MODULE, | |
417 | }, | |
418 | }; | |
419 | ||
420 | static int __init xilinx_spi_init(void) | |
421 | { | |
422 | return platform_driver_register(&xilinx_spi_driver); | |
423 | } | |
424 | module_init(xilinx_spi_init); | |
425 | ||
426 | static void __exit xilinx_spi_exit(void) | |
427 | { | |
428 | platform_driver_unregister(&xilinx_spi_driver); | |
429 | } | |
430 | module_exit(xilinx_spi_exit); | |
431 | ||
432 | MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>"); | |
433 | MODULE_DESCRIPTION("Xilinx SPI driver"); | |
434 | MODULE_LICENSE("GPL"); |