Commit | Line | Data |
---|---|---|
b2441318 | 1 | /* SPDX-License-Identifier: GPL-2.0 */ |
9d99a2e3 RV |
2 | /* |
3 | * The canonical list of T10 Additional Sense Codes is available at: | |
4 | * http://www.t10.org/lists/asc-num.txt [most recent: 20141221] | |
5 | */ | |
6 | ||
7 | SENSE_CODE(0x0000, "No additional sense information") | |
8 | SENSE_CODE(0x0001, "Filemark detected") | |
9 | SENSE_CODE(0x0002, "End-of-partition/medium detected") | |
10 | SENSE_CODE(0x0003, "Setmark detected") | |
11 | SENSE_CODE(0x0004, "Beginning-of-partition/medium detected") | |
12 | SENSE_CODE(0x0005, "End-of-data detected") | |
13 | SENSE_CODE(0x0006, "I/O process terminated") | |
14 | SENSE_CODE(0x0007, "Programmable early warning detected") | |
15 | SENSE_CODE(0x0011, "Audio play operation in progress") | |
16 | SENSE_CODE(0x0012, "Audio play operation paused") | |
17 | SENSE_CODE(0x0013, "Audio play operation successfully completed") | |
18 | SENSE_CODE(0x0014, "Audio play operation stopped due to error") | |
19 | SENSE_CODE(0x0015, "No current audio status to return") | |
20 | SENSE_CODE(0x0016, "Operation in progress") | |
21 | SENSE_CODE(0x0017, "Cleaning requested") | |
22 | SENSE_CODE(0x0018, "Erase operation in progress") | |
23 | SENSE_CODE(0x0019, "Locate operation in progress") | |
24 | SENSE_CODE(0x001A, "Rewind operation in progress") | |
25 | SENSE_CODE(0x001B, "Set capacity operation in progress") | |
26 | SENSE_CODE(0x001C, "Verify operation in progress") | |
27 | SENSE_CODE(0x001D, "ATA pass through information available") | |
28 | SENSE_CODE(0x001E, "Conflicting SA creation request") | |
29 | SENSE_CODE(0x001F, "Logical unit transitioning to another power condition") | |
30 | SENSE_CODE(0x0020, "Extended copy information available") | |
31 | SENSE_CODE(0x0021, "Atomic command aborted due to ACA") | |
32 | ||
33 | SENSE_CODE(0x0100, "No index/sector signal") | |
34 | ||
35 | SENSE_CODE(0x0200, "No seek complete") | |
36 | ||
37 | SENSE_CODE(0x0300, "Peripheral device write fault") | |
38 | SENSE_CODE(0x0301, "No write current") | |
39 | SENSE_CODE(0x0302, "Excessive write errors") | |
40 | ||
41 | SENSE_CODE(0x0400, "Logical unit not ready, cause not reportable") | |
42 | SENSE_CODE(0x0401, "Logical unit is in process of becoming ready") | |
43 | SENSE_CODE(0x0402, "Logical unit not ready, initializing command required") | |
44 | SENSE_CODE(0x0403, "Logical unit not ready, manual intervention required") | |
45 | SENSE_CODE(0x0404, "Logical unit not ready, format in progress") | |
46 | SENSE_CODE(0x0405, "Logical unit not ready, rebuild in progress") | |
47 | SENSE_CODE(0x0406, "Logical unit not ready, recalculation in progress") | |
48 | SENSE_CODE(0x0407, "Logical unit not ready, operation in progress") | |
49 | SENSE_CODE(0x0408, "Logical unit not ready, long write in progress") | |
50 | SENSE_CODE(0x0409, "Logical unit not ready, self-test in progress") | |
51 | SENSE_CODE(0x040A, "Logical unit not accessible, asymmetric access state transition") | |
52 | SENSE_CODE(0x040B, "Logical unit not accessible, target port in standby state") | |
53 | SENSE_CODE(0x040C, "Logical unit not accessible, target port in unavailable state") | |
54 | SENSE_CODE(0x040D, "Logical unit not ready, structure check required") | |
55 | SENSE_CODE(0x040E, "Logical unit not ready, security session in progress") | |
56 | SENSE_CODE(0x0410, "Logical unit not ready, auxiliary memory not accessible") | |
57 | SENSE_CODE(0x0411, "Logical unit not ready, notify (enable spinup) required") | |
58 | SENSE_CODE(0x0412, "Logical unit not ready, offline") | |
59 | SENSE_CODE(0x0413, "Logical unit not ready, SA creation in progress") | |
60 | SENSE_CODE(0x0414, "Logical unit not ready, space allocation in progress") | |
61 | SENSE_CODE(0x0415, "Logical unit not ready, robotics disabled") | |
62 | SENSE_CODE(0x0416, "Logical unit not ready, configuration required") | |
63 | SENSE_CODE(0x0417, "Logical unit not ready, calibration required") | |
64 | SENSE_CODE(0x0418, "Logical unit not ready, a door is open") | |
65 | SENSE_CODE(0x0419, "Logical unit not ready, operating in sequential mode") | |
66 | SENSE_CODE(0x041A, "Logical unit not ready, start stop unit command in progress") | |
67 | SENSE_CODE(0x041B, "Logical unit not ready, sanitize in progress") | |
68 | SENSE_CODE(0x041C, "Logical unit not ready, additional power use not yet granted") | |
69 | SENSE_CODE(0x041D, "Logical unit not ready, configuration in progress") | |
70 | SENSE_CODE(0x041E, "Logical unit not ready, microcode activation required") | |
71 | SENSE_CODE(0x041F, "Logical unit not ready, microcode download required") | |
72 | SENSE_CODE(0x0420, "Logical unit not ready, logical unit reset required") | |
73 | SENSE_CODE(0x0421, "Logical unit not ready, hard reset required") | |
74 | SENSE_CODE(0x0422, "Logical unit not ready, power cycle required") | |
75 | ||
76 | SENSE_CODE(0x0500, "Logical unit does not respond to selection") | |
77 | ||
78 | SENSE_CODE(0x0600, "No reference position found") | |
79 | ||
80 | SENSE_CODE(0x0700, "Multiple peripheral devices selected") | |
81 | ||
82 | SENSE_CODE(0x0800, "Logical unit communication failure") | |
83 | SENSE_CODE(0x0801, "Logical unit communication time-out") | |
84 | SENSE_CODE(0x0802, "Logical unit communication parity error") | |
85 | SENSE_CODE(0x0803, "Logical unit communication CRC error (Ultra-DMA/32)") | |
86 | SENSE_CODE(0x0804, "Unreachable copy target") | |
87 | ||
88 | SENSE_CODE(0x0900, "Track following error") | |
89 | SENSE_CODE(0x0901, "Tracking servo failure") | |
90 | SENSE_CODE(0x0902, "Focus servo failure") | |
91 | SENSE_CODE(0x0903, "Spindle servo failure") | |
92 | SENSE_CODE(0x0904, "Head select fault") | |
93 | SENSE_CODE(0x0905, "Vibration induced tracking error") | |
94 | ||
95 | SENSE_CODE(0x0A00, "Error log overflow") | |
96 | ||
97 | SENSE_CODE(0x0B00, "Warning") | |
98 | SENSE_CODE(0x0B01, "Warning - specified temperature exceeded") | |
99 | SENSE_CODE(0x0B02, "Warning - enclosure degraded") | |
100 | SENSE_CODE(0x0B03, "Warning - background self-test failed") | |
101 | SENSE_CODE(0x0B04, "Warning - background pre-scan detected medium error") | |
102 | SENSE_CODE(0x0B05, "Warning - background medium scan detected medium error") | |
103 | SENSE_CODE(0x0B06, "Warning - non-volatile cache now volatile") | |
104 | SENSE_CODE(0x0B07, "Warning - degraded power to non-volatile cache") | |
105 | SENSE_CODE(0x0B08, "Warning - power loss expected") | |
106 | SENSE_CODE(0x0B09, "Warning - device statistics notification active") | |
107 | ||
108 | SENSE_CODE(0x0C00, "Write error") | |
109 | SENSE_CODE(0x0C01, "Write error - recovered with auto reallocation") | |
110 | SENSE_CODE(0x0C02, "Write error - auto reallocation failed") | |
111 | SENSE_CODE(0x0C03, "Write error - recommend reassignment") | |
112 | SENSE_CODE(0x0C04, "Compression check miscompare error") | |
113 | SENSE_CODE(0x0C05, "Data expansion occurred during compression") | |
114 | SENSE_CODE(0x0C06, "Block not compressible") | |
115 | SENSE_CODE(0x0C07, "Write error - recovery needed") | |
116 | SENSE_CODE(0x0C08, "Write error - recovery failed") | |
117 | SENSE_CODE(0x0C09, "Write error - loss of streaming") | |
118 | SENSE_CODE(0x0C0A, "Write error - padding blocks added") | |
119 | SENSE_CODE(0x0C0B, "Auxiliary memory write error") | |
120 | SENSE_CODE(0x0C0C, "Write error - unexpected unsolicited data") | |
121 | SENSE_CODE(0x0C0D, "Write error - not enough unsolicited data") | |
122 | SENSE_CODE(0x0C0E, "Multiple write errors") | |
123 | SENSE_CODE(0x0C0F, "Defects in error window") | |
124 | SENSE_CODE(0x0C10, "Incomplete multiple atomic write operations") | |
125 | ||
126 | SENSE_CODE(0x0D00, "Error detected by third party temporary initiator") | |
127 | SENSE_CODE(0x0D01, "Third party device failure") | |
128 | SENSE_CODE(0x0D02, "Copy target device not reachable") | |
129 | SENSE_CODE(0x0D03, "Incorrect copy target device type") | |
130 | SENSE_CODE(0x0D04, "Copy target device data underrun") | |
131 | SENSE_CODE(0x0D05, "Copy target device data overrun") | |
132 | ||
133 | SENSE_CODE(0x0E00, "Invalid information unit") | |
134 | SENSE_CODE(0x0E01, "Information unit too short") | |
135 | SENSE_CODE(0x0E02, "Information unit too long") | |
136 | SENSE_CODE(0x0E03, "Invalid field in command information unit") | |
137 | ||
138 | SENSE_CODE(0x1000, "Id CRC or ECC error") | |
139 | SENSE_CODE(0x1001, "Logical block guard check failed") | |
140 | SENSE_CODE(0x1002, "Logical block application tag check failed") | |
141 | SENSE_CODE(0x1003, "Logical block reference tag check failed") | |
142 | SENSE_CODE(0x1004, "Logical block protection error on recover buffered data") | |
143 | SENSE_CODE(0x1005, "Logical block protection method error") | |
144 | ||
145 | SENSE_CODE(0x1100, "Unrecovered read error") | |
146 | SENSE_CODE(0x1101, "Read retries exhausted") | |
147 | SENSE_CODE(0x1102, "Error too long to correct") | |
148 | SENSE_CODE(0x1103, "Multiple read errors") | |
149 | SENSE_CODE(0x1104, "Unrecovered read error - auto reallocate failed") | |
150 | SENSE_CODE(0x1105, "L-EC uncorrectable error") | |
151 | SENSE_CODE(0x1106, "CIRC unrecovered error") | |
152 | SENSE_CODE(0x1107, "Data re-synchronization error") | |
153 | SENSE_CODE(0x1108, "Incomplete block read") | |
154 | SENSE_CODE(0x1109, "No gap found") | |
155 | SENSE_CODE(0x110A, "Miscorrected error") | |
156 | SENSE_CODE(0x110B, "Unrecovered read error - recommend reassignment") | |
157 | SENSE_CODE(0x110C, "Unrecovered read error - recommend rewrite the data") | |
158 | SENSE_CODE(0x110D, "De-compression CRC error") | |
159 | SENSE_CODE(0x110E, "Cannot decompress using declared algorithm") | |
160 | SENSE_CODE(0x110F, "Error reading UPC/EAN number") | |
161 | SENSE_CODE(0x1110, "Error reading ISRC number") | |
162 | SENSE_CODE(0x1111, "Read error - loss of streaming") | |
163 | SENSE_CODE(0x1112, "Auxiliary memory read error") | |
164 | SENSE_CODE(0x1113, "Read error - failed retransmission request") | |
165 | SENSE_CODE(0x1114, "Read error - lba marked bad by application client") | |
166 | SENSE_CODE(0x1115, "Write after sanitize required") | |
167 | ||
168 | SENSE_CODE(0x1200, "Address mark not found for id field") | |
169 | ||
170 | SENSE_CODE(0x1300, "Address mark not found for data field") | |
171 | ||
172 | SENSE_CODE(0x1400, "Recorded entity not found") | |
173 | SENSE_CODE(0x1401, "Record not found") | |
174 | SENSE_CODE(0x1402, "Filemark or setmark not found") | |
175 | SENSE_CODE(0x1403, "End-of-data not found") | |
176 | SENSE_CODE(0x1404, "Block sequence error") | |
177 | SENSE_CODE(0x1405, "Record not found - recommend reassignment") | |
178 | SENSE_CODE(0x1406, "Record not found - data auto-reallocated") | |
179 | SENSE_CODE(0x1407, "Locate operation failure") | |
180 | ||
181 | SENSE_CODE(0x1500, "Random positioning error") | |
182 | SENSE_CODE(0x1501, "Mechanical positioning error") | |
183 | SENSE_CODE(0x1502, "Positioning error detected by read of medium") | |
184 | ||
185 | SENSE_CODE(0x1600, "Data synchronization mark error") | |
186 | SENSE_CODE(0x1601, "Data sync error - data rewritten") | |
187 | SENSE_CODE(0x1602, "Data sync error - recommend rewrite") | |
188 | SENSE_CODE(0x1603, "Data sync error - data auto-reallocated") | |
189 | SENSE_CODE(0x1604, "Data sync error - recommend reassignment") | |
190 | ||
191 | SENSE_CODE(0x1700, "Recovered data with no error correction applied") | |
192 | SENSE_CODE(0x1701, "Recovered data with retries") | |
193 | SENSE_CODE(0x1702, "Recovered data with positive head offset") | |
194 | SENSE_CODE(0x1703, "Recovered data with negative head offset") | |
195 | SENSE_CODE(0x1704, "Recovered data with retries and/or circ applied") | |
196 | SENSE_CODE(0x1705, "Recovered data using previous sector id") | |
197 | SENSE_CODE(0x1706, "Recovered data without ECC - data auto-reallocated") | |
198 | SENSE_CODE(0x1707, "Recovered data without ECC - recommend reassignment") | |
199 | SENSE_CODE(0x1708, "Recovered data without ECC - recommend rewrite") | |
200 | SENSE_CODE(0x1709, "Recovered data without ECC - data rewritten") | |
201 | ||
202 | SENSE_CODE(0x1800, "Recovered data with error correction applied") | |
203 | SENSE_CODE(0x1801, "Recovered data with error corr. & retries applied") | |
204 | SENSE_CODE(0x1802, "Recovered data - data auto-reallocated") | |
205 | SENSE_CODE(0x1803, "Recovered data with CIRC") | |
206 | SENSE_CODE(0x1804, "Recovered data with L-EC") | |
207 | SENSE_CODE(0x1805, "Recovered data - recommend reassignment") | |
208 | SENSE_CODE(0x1806, "Recovered data - recommend rewrite") | |
209 | SENSE_CODE(0x1807, "Recovered data with ECC - data rewritten") | |
210 | SENSE_CODE(0x1808, "Recovered data with linking") | |
211 | ||
212 | SENSE_CODE(0x1900, "Defect list error") | |
213 | SENSE_CODE(0x1901, "Defect list not available") | |
214 | SENSE_CODE(0x1902, "Defect list error in primary list") | |
215 | SENSE_CODE(0x1903, "Defect list error in grown list") | |
216 | ||
217 | SENSE_CODE(0x1A00, "Parameter list length error") | |
218 | ||
219 | SENSE_CODE(0x1B00, "Synchronous data transfer error") | |
220 | ||
221 | SENSE_CODE(0x1C00, "Defect list not found") | |
222 | SENSE_CODE(0x1C01, "Primary defect list not found") | |
223 | SENSE_CODE(0x1C02, "Grown defect list not found") | |
224 | ||
225 | SENSE_CODE(0x1D00, "Miscompare during verify operation") | |
226 | SENSE_CODE(0x1D01, "Miscompare verify of unmapped LBA") | |
227 | ||
228 | SENSE_CODE(0x1E00, "Recovered id with ECC correction") | |
229 | ||
230 | SENSE_CODE(0x1F00, "Partial defect list transfer") | |
231 | ||
232 | SENSE_CODE(0x2000, "Invalid command operation code") | |
233 | SENSE_CODE(0x2001, "Access denied - initiator pending-enrolled") | |
234 | SENSE_CODE(0x2002, "Access denied - no access rights") | |
235 | SENSE_CODE(0x2003, "Access denied - invalid mgmt id key") | |
236 | SENSE_CODE(0x2004, "Illegal command while in write capable state") | |
237 | SENSE_CODE(0x2005, "Obsolete") | |
238 | SENSE_CODE(0x2006, "Illegal command while in explicit address mode") | |
239 | SENSE_CODE(0x2007, "Illegal command while in implicit address mode") | |
240 | SENSE_CODE(0x2008, "Access denied - enrollment conflict") | |
241 | SENSE_CODE(0x2009, "Access denied - invalid LU identifier") | |
242 | SENSE_CODE(0x200A, "Access denied - invalid proxy token") | |
243 | SENSE_CODE(0x200B, "Access denied - ACL LUN conflict") | |
244 | SENSE_CODE(0x200C, "Illegal command when not in append-only mode") | |
245 | ||
246 | SENSE_CODE(0x2100, "Logical block address out of range") | |
247 | SENSE_CODE(0x2101, "Invalid element address") | |
248 | SENSE_CODE(0x2102, "Invalid address for write") | |
249 | SENSE_CODE(0x2103, "Invalid write crossing layer jump") | |
250 | SENSE_CODE(0x2104, "Unaligned write command") | |
251 | SENSE_CODE(0x2105, "Write boundary violation") | |
252 | SENSE_CODE(0x2106, "Attempt to read invalid data") | |
253 | SENSE_CODE(0x2107, "Read boundary violation") | |
254 | ||
255 | SENSE_CODE(0x2200, "Illegal function (use 20 00, 24 00, or 26 00)") | |
256 | ||
257 | SENSE_CODE(0x2300, "Invalid token operation, cause not reportable") | |
258 | SENSE_CODE(0x2301, "Invalid token operation, unsupported token type") | |
259 | SENSE_CODE(0x2302, "Invalid token operation, remote token usage not supported") | |
260 | SENSE_CODE(0x2303, "Invalid token operation, remote rod token creation not supported") | |
261 | SENSE_CODE(0x2304, "Invalid token operation, token unknown") | |
262 | SENSE_CODE(0x2305, "Invalid token operation, token corrupt") | |
263 | SENSE_CODE(0x2306, "Invalid token operation, token revoked") | |
264 | SENSE_CODE(0x2307, "Invalid token operation, token expired") | |
265 | SENSE_CODE(0x2308, "Invalid token operation, token cancelled") | |
266 | SENSE_CODE(0x2309, "Invalid token operation, token deleted") | |
267 | SENSE_CODE(0x230A, "Invalid token operation, invalid token length") | |
268 | ||
269 | SENSE_CODE(0x2400, "Invalid field in cdb") | |
270 | SENSE_CODE(0x2401, "CDB decryption error") | |
271 | SENSE_CODE(0x2402, "Obsolete") | |
272 | SENSE_CODE(0x2403, "Obsolete") | |
273 | SENSE_CODE(0x2404, "Security audit value frozen") | |
274 | SENSE_CODE(0x2405, "Security working key frozen") | |
275 | SENSE_CODE(0x2406, "Nonce not unique") | |
276 | SENSE_CODE(0x2407, "Nonce timestamp out of range") | |
277 | SENSE_CODE(0x2408, "Invalid XCDB") | |
278 | ||
279 | SENSE_CODE(0x2500, "Logical unit not supported") | |
280 | ||
281 | SENSE_CODE(0x2600, "Invalid field in parameter list") | |
282 | SENSE_CODE(0x2601, "Parameter not supported") | |
283 | SENSE_CODE(0x2602, "Parameter value invalid") | |
284 | SENSE_CODE(0x2603, "Threshold parameters not supported") | |
285 | SENSE_CODE(0x2604, "Invalid release of persistent reservation") | |
286 | SENSE_CODE(0x2605, "Data decryption error") | |
287 | SENSE_CODE(0x2606, "Too many target descriptors") | |
288 | SENSE_CODE(0x2607, "Unsupported target descriptor type code") | |
289 | SENSE_CODE(0x2608, "Too many segment descriptors") | |
290 | SENSE_CODE(0x2609, "Unsupported segment descriptor type code") | |
291 | SENSE_CODE(0x260A, "Unexpected inexact segment") | |
292 | SENSE_CODE(0x260B, "Inline data length exceeded") | |
293 | SENSE_CODE(0x260C, "Invalid operation for copy source or destination") | |
294 | SENSE_CODE(0x260D, "Copy segment granularity violation") | |
295 | SENSE_CODE(0x260E, "Invalid parameter while port is enabled") | |
296 | SENSE_CODE(0x260F, "Invalid data-out buffer integrity check value") | |
297 | SENSE_CODE(0x2610, "Data decryption key fail limit reached") | |
298 | SENSE_CODE(0x2611, "Incomplete key-associated data set") | |
299 | SENSE_CODE(0x2612, "Vendor specific key reference not found") | |
300 | ||
301 | SENSE_CODE(0x2700, "Write protected") | |
302 | SENSE_CODE(0x2701, "Hardware write protected") | |
303 | SENSE_CODE(0x2702, "Logical unit software write protected") | |
304 | SENSE_CODE(0x2703, "Associated write protect") | |
305 | SENSE_CODE(0x2704, "Persistent write protect") | |
306 | SENSE_CODE(0x2705, "Permanent write protect") | |
307 | SENSE_CODE(0x2706, "Conditional write protect") | |
308 | SENSE_CODE(0x2707, "Space allocation failed write protect") | |
309 | SENSE_CODE(0x2708, "Zone is read only") | |
310 | ||
311 | SENSE_CODE(0x2800, "Not ready to ready change, medium may have changed") | |
312 | SENSE_CODE(0x2801, "Import or export element accessed") | |
313 | SENSE_CODE(0x2802, "Format-layer may have changed") | |
314 | SENSE_CODE(0x2803, "Import/export element accessed, medium changed") | |
315 | ||
316 | SENSE_CODE(0x2900, "Power on, reset, or bus device reset occurred") | |
317 | SENSE_CODE(0x2901, "Power on occurred") | |
318 | SENSE_CODE(0x2902, "Scsi bus reset occurred") | |
319 | SENSE_CODE(0x2903, "Bus device reset function occurred") | |
320 | SENSE_CODE(0x2904, "Device internal reset") | |
321 | SENSE_CODE(0x2905, "Transceiver mode changed to single-ended") | |
322 | SENSE_CODE(0x2906, "Transceiver mode changed to lvd") | |
323 | SENSE_CODE(0x2907, "I_T nexus loss occurred") | |
324 | ||
325 | SENSE_CODE(0x2A00, "Parameters changed") | |
326 | SENSE_CODE(0x2A01, "Mode parameters changed") | |
327 | SENSE_CODE(0x2A02, "Log parameters changed") | |
328 | SENSE_CODE(0x2A03, "Reservations preempted") | |
329 | SENSE_CODE(0x2A04, "Reservations released") | |
330 | SENSE_CODE(0x2A05, "Registrations preempted") | |
331 | SENSE_CODE(0x2A06, "Asymmetric access state changed") | |
332 | SENSE_CODE(0x2A07, "Implicit asymmetric access state transition failed") | |
333 | SENSE_CODE(0x2A08, "Priority changed") | |
334 | SENSE_CODE(0x2A09, "Capacity data has changed") | |
335 | SENSE_CODE(0x2A0A, "Error history I_T nexus cleared") | |
336 | SENSE_CODE(0x2A0B, "Error history snapshot released") | |
337 | SENSE_CODE(0x2A0C, "Error recovery attributes have changed") | |
338 | SENSE_CODE(0x2A0D, "Data encryption capabilities changed") | |
339 | SENSE_CODE(0x2A10, "Timestamp changed") | |
340 | SENSE_CODE(0x2A11, "Data encryption parameters changed by another i_t nexus") | |
341 | SENSE_CODE(0x2A12, "Data encryption parameters changed by vendor specific event") | |
342 | SENSE_CODE(0x2A13, "Data encryption key instance counter has changed") | |
343 | SENSE_CODE(0x2A14, "SA creation capabilities data has changed") | |
344 | SENSE_CODE(0x2A15, "Medium removal prevention preempted") | |
345 | ||
346 | SENSE_CODE(0x2B00, "Copy cannot execute since host cannot disconnect") | |
347 | ||
348 | SENSE_CODE(0x2C00, "Command sequence error") | |
349 | SENSE_CODE(0x2C01, "Too many windows specified") | |
350 | SENSE_CODE(0x2C02, "Invalid combination of windows specified") | |
351 | SENSE_CODE(0x2C03, "Current program area is not empty") | |
352 | SENSE_CODE(0x2C04, "Current program area is empty") | |
353 | SENSE_CODE(0x2C05, "Illegal power condition request") | |
354 | SENSE_CODE(0x2C06, "Persistent prevent conflict") | |
355 | SENSE_CODE(0x2C07, "Previous busy status") | |
356 | SENSE_CODE(0x2C08, "Previous task set full status") | |
357 | SENSE_CODE(0x2C09, "Previous reservation conflict status") | |
358 | SENSE_CODE(0x2C0A, "Partition or collection contains user objects") | |
359 | SENSE_CODE(0x2C0B, "Not reserved") | |
360 | SENSE_CODE(0x2C0C, "Orwrite generation does not match") | |
361 | SENSE_CODE(0x2C0D, "Reset write pointer not allowed") | |
362 | SENSE_CODE(0x2C0E, "Zone is offline") | |
363 | ||
364 | SENSE_CODE(0x2D00, "Overwrite error on update in place") | |
365 | ||
366 | SENSE_CODE(0x2E00, "Insufficient time for operation") | |
367 | SENSE_CODE(0x2E01, "Command timeout before processing") | |
368 | SENSE_CODE(0x2E02, "Command timeout during processing") | |
369 | SENSE_CODE(0x2E03, "Command timeout during processing due to error recovery") | |
370 | ||
371 | SENSE_CODE(0x2F00, "Commands cleared by another initiator") | |
372 | SENSE_CODE(0x2F01, "Commands cleared by power loss notification") | |
373 | SENSE_CODE(0x2F02, "Commands cleared by device server") | |
374 | SENSE_CODE(0x2F03, "Some commands cleared by queuing layer event") | |
375 | ||
376 | SENSE_CODE(0x3000, "Incompatible medium installed") | |
377 | SENSE_CODE(0x3001, "Cannot read medium - unknown format") | |
378 | SENSE_CODE(0x3002, "Cannot read medium - incompatible format") | |
379 | SENSE_CODE(0x3003, "Cleaning cartridge installed") | |
380 | SENSE_CODE(0x3004, "Cannot write medium - unknown format") | |
381 | SENSE_CODE(0x3005, "Cannot write medium - incompatible format") | |
382 | SENSE_CODE(0x3006, "Cannot format medium - incompatible medium") | |
383 | SENSE_CODE(0x3007, "Cleaning failure") | |
384 | SENSE_CODE(0x3008, "Cannot write - application code mismatch") | |
385 | SENSE_CODE(0x3009, "Current session not fixated for append") | |
386 | SENSE_CODE(0x300A, "Cleaning request rejected") | |
387 | SENSE_CODE(0x300C, "WORM medium - overwrite attempted") | |
388 | SENSE_CODE(0x300D, "WORM medium - integrity check") | |
389 | SENSE_CODE(0x3010, "Medium not formatted") | |
390 | SENSE_CODE(0x3011, "Incompatible volume type") | |
391 | SENSE_CODE(0x3012, "Incompatible volume qualifier") | |
392 | SENSE_CODE(0x3013, "Cleaning volume expired") | |
393 | ||
394 | SENSE_CODE(0x3100, "Medium format corrupted") | |
395 | SENSE_CODE(0x3101, "Format command failed") | |
396 | SENSE_CODE(0x3102, "Zoned formatting failed due to spare linking") | |
397 | SENSE_CODE(0x3103, "Sanitize command failed") | |
398 | ||
399 | SENSE_CODE(0x3200, "No defect spare location available") | |
400 | SENSE_CODE(0x3201, "Defect list update failure") | |
401 | ||
402 | SENSE_CODE(0x3300, "Tape length error") | |
403 | ||
404 | SENSE_CODE(0x3400, "Enclosure failure") | |
405 | ||
406 | SENSE_CODE(0x3500, "Enclosure services failure") | |
407 | SENSE_CODE(0x3501, "Unsupported enclosure function") | |
408 | SENSE_CODE(0x3502, "Enclosure services unavailable") | |
409 | SENSE_CODE(0x3503, "Enclosure services transfer failure") | |
410 | SENSE_CODE(0x3504, "Enclosure services transfer refused") | |
411 | SENSE_CODE(0x3505, "Enclosure services checksum error") | |
412 | ||
413 | SENSE_CODE(0x3600, "Ribbon, ink, or toner failure") | |
414 | ||
415 | SENSE_CODE(0x3700, "Rounded parameter") | |
416 | ||
417 | SENSE_CODE(0x3800, "Event status notification") | |
418 | SENSE_CODE(0x3802, "Esn - power management class event") | |
419 | SENSE_CODE(0x3804, "Esn - media class event") | |
420 | SENSE_CODE(0x3806, "Esn - device busy class event") | |
421 | SENSE_CODE(0x3807, "Thin Provisioning soft threshold reached") | |
422 | ||
423 | SENSE_CODE(0x3900, "Saving parameters not supported") | |
424 | ||
425 | SENSE_CODE(0x3A00, "Medium not present") | |
426 | SENSE_CODE(0x3A01, "Medium not present - tray closed") | |
427 | SENSE_CODE(0x3A02, "Medium not present - tray open") | |
428 | SENSE_CODE(0x3A03, "Medium not present - loadable") | |
429 | SENSE_CODE(0x3A04, "Medium not present - medium auxiliary memory accessible") | |
430 | ||
431 | SENSE_CODE(0x3B00, "Sequential positioning error") | |
432 | SENSE_CODE(0x3B01, "Tape position error at beginning-of-medium") | |
433 | SENSE_CODE(0x3B02, "Tape position error at end-of-medium") | |
434 | SENSE_CODE(0x3B03, "Tape or electronic vertical forms unit not ready") | |
435 | SENSE_CODE(0x3B04, "Slew failure") | |
436 | SENSE_CODE(0x3B05, "Paper jam") | |
437 | SENSE_CODE(0x3B06, "Failed to sense top-of-form") | |
438 | SENSE_CODE(0x3B07, "Failed to sense bottom-of-form") | |
439 | SENSE_CODE(0x3B08, "Reposition error") | |
440 | SENSE_CODE(0x3B09, "Read past end of medium") | |
441 | SENSE_CODE(0x3B0A, "Read past beginning of medium") | |
442 | SENSE_CODE(0x3B0B, "Position past end of medium") | |
443 | SENSE_CODE(0x3B0C, "Position past beginning of medium") | |
444 | SENSE_CODE(0x3B0D, "Medium destination element full") | |
445 | SENSE_CODE(0x3B0E, "Medium source element empty") | |
446 | SENSE_CODE(0x3B0F, "End of medium reached") | |
447 | SENSE_CODE(0x3B11, "Medium magazine not accessible") | |
448 | SENSE_CODE(0x3B12, "Medium magazine removed") | |
449 | SENSE_CODE(0x3B13, "Medium magazine inserted") | |
450 | SENSE_CODE(0x3B14, "Medium magazine locked") | |
451 | SENSE_CODE(0x3B15, "Medium magazine unlocked") | |
452 | SENSE_CODE(0x3B16, "Mechanical positioning or changer error") | |
453 | SENSE_CODE(0x3B17, "Read past end of user object") | |
454 | SENSE_CODE(0x3B18, "Element disabled") | |
455 | SENSE_CODE(0x3B19, "Element enabled") | |
456 | SENSE_CODE(0x3B1A, "Data transfer device removed") | |
457 | SENSE_CODE(0x3B1B, "Data transfer device inserted") | |
458 | SENSE_CODE(0x3B1C, "Too many logical objects on partition to support operation") | |
459 | ||
460 | SENSE_CODE(0x3D00, "Invalid bits in identify message") | |
461 | ||
462 | SENSE_CODE(0x3E00, "Logical unit has not self-configured yet") | |
463 | SENSE_CODE(0x3E01, "Logical unit failure") | |
464 | SENSE_CODE(0x3E02, "Timeout on logical unit") | |
465 | SENSE_CODE(0x3E03, "Logical unit failed self-test") | |
466 | SENSE_CODE(0x3E04, "Logical unit unable to update self-test log") | |
467 | ||
468 | SENSE_CODE(0x3F00, "Target operating conditions have changed") | |
469 | SENSE_CODE(0x3F01, "Microcode has been changed") | |
470 | SENSE_CODE(0x3F02, "Changed operating definition") | |
471 | SENSE_CODE(0x3F03, "Inquiry data has changed") | |
472 | SENSE_CODE(0x3F04, "Component device attached") | |
473 | SENSE_CODE(0x3F05, "Device identifier changed") | |
474 | SENSE_CODE(0x3F06, "Redundancy group created or modified") | |
475 | SENSE_CODE(0x3F07, "Redundancy group deleted") | |
476 | SENSE_CODE(0x3F08, "Spare created or modified") | |
477 | SENSE_CODE(0x3F09, "Spare deleted") | |
478 | SENSE_CODE(0x3F0A, "Volume set created or modified") | |
479 | SENSE_CODE(0x3F0B, "Volume set deleted") | |
480 | SENSE_CODE(0x3F0C, "Volume set deassigned") | |
481 | SENSE_CODE(0x3F0D, "Volume set reassigned") | |
482 | SENSE_CODE(0x3F0E, "Reported luns data has changed") | |
483 | SENSE_CODE(0x3F0F, "Echo buffer overwritten") | |
484 | SENSE_CODE(0x3F10, "Medium loadable") | |
485 | SENSE_CODE(0x3F11, "Medium auxiliary memory accessible") | |
486 | SENSE_CODE(0x3F12, "iSCSI IP address added") | |
487 | SENSE_CODE(0x3F13, "iSCSI IP address removed") | |
488 | SENSE_CODE(0x3F14, "iSCSI IP address changed") | |
489 | SENSE_CODE(0x3F15, "Inspect referrals sense descriptors") | |
490 | SENSE_CODE(0x3F16, "Microcode has been changed without reset") | |
491 | /* | |
492 | * SENSE_CODE(0x40NN, "Ram failure") | |
493 | * SENSE_CODE(0x40NN, "Diagnostic failure on component nn") | |
494 | * SENSE_CODE(0x41NN, "Data path failure") | |
495 | * SENSE_CODE(0x42NN, "Power-on or self-test failure") | |
496 | */ | |
497 | SENSE_CODE(0x4300, "Message error") | |
498 | ||
499 | SENSE_CODE(0x4400, "Internal target failure") | |
500 | SENSE_CODE(0x4401, "Persistent reservation information lost") | |
501 | SENSE_CODE(0x4471, "ATA device failed set features") | |
502 | ||
503 | SENSE_CODE(0x4500, "Select or reselect failure") | |
504 | ||
505 | SENSE_CODE(0x4600, "Unsuccessful soft reset") | |
506 | ||
507 | SENSE_CODE(0x4700, "Scsi parity error") | |
508 | SENSE_CODE(0x4701, "Data phase CRC error detected") | |
509 | SENSE_CODE(0x4702, "Scsi parity error detected during st data phase") | |
510 | SENSE_CODE(0x4703, "Information unit iuCRC error detected") | |
511 | SENSE_CODE(0x4704, "Asynchronous information protection error detected") | |
512 | SENSE_CODE(0x4705, "Protocol service CRC error") | |
513 | SENSE_CODE(0x4706, "Phy test function in progress") | |
514 | SENSE_CODE(0x477f, "Some commands cleared by iSCSI Protocol event") | |
515 | ||
516 | SENSE_CODE(0x4800, "Initiator detected error message received") | |
517 | ||
518 | SENSE_CODE(0x4900, "Invalid message error") | |
519 | ||
520 | SENSE_CODE(0x4A00, "Command phase error") | |
521 | ||
522 | SENSE_CODE(0x4B00, "Data phase error") | |
523 | SENSE_CODE(0x4B01, "Invalid target port transfer tag received") | |
524 | SENSE_CODE(0x4B02, "Too much write data") | |
525 | SENSE_CODE(0x4B03, "Ack/nak timeout") | |
526 | SENSE_CODE(0x4B04, "Nak received") | |
527 | SENSE_CODE(0x4B05, "Data offset error") | |
528 | SENSE_CODE(0x4B06, "Initiator response timeout") | |
529 | SENSE_CODE(0x4B07, "Connection lost") | |
530 | SENSE_CODE(0x4B08, "Data-in buffer overflow - data buffer size") | |
531 | SENSE_CODE(0x4B09, "Data-in buffer overflow - data buffer descriptor area") | |
532 | SENSE_CODE(0x4B0A, "Data-in buffer error") | |
533 | SENSE_CODE(0x4B0B, "Data-out buffer overflow - data buffer size") | |
534 | SENSE_CODE(0x4B0C, "Data-out buffer overflow - data buffer descriptor area") | |
535 | SENSE_CODE(0x4B0D, "Data-out buffer error") | |
536 | SENSE_CODE(0x4B0E, "PCIe fabric error") | |
537 | SENSE_CODE(0x4B0F, "PCIe completion timeout") | |
538 | SENSE_CODE(0x4B10, "PCIe completer abort") | |
539 | SENSE_CODE(0x4B11, "PCIe poisoned tlp received") | |
540 | SENSE_CODE(0x4B12, "PCIe eCRC check failed") | |
541 | SENSE_CODE(0x4B13, "PCIe unsupported request") | |
542 | SENSE_CODE(0x4B14, "PCIe acs violation") | |
543 | SENSE_CODE(0x4B15, "PCIe tlp prefix blocked") | |
544 | ||
545 | SENSE_CODE(0x4C00, "Logical unit failed self-configuration") | |
546 | /* | |
547 | * SENSE_CODE(0x4DNN, "Tagged overlapped commands (nn = queue tag)") | |
548 | */ | |
549 | SENSE_CODE(0x4E00, "Overlapped commands attempted") | |
550 | ||
551 | SENSE_CODE(0x5000, "Write append error") | |
552 | SENSE_CODE(0x5001, "Write append position error") | |
553 | SENSE_CODE(0x5002, "Position error related to timing") | |
554 | ||
555 | SENSE_CODE(0x5100, "Erase failure") | |
556 | SENSE_CODE(0x5101, "Erase failure - incomplete erase operation detected") | |
557 | ||
558 | SENSE_CODE(0x5200, "Cartridge fault") | |
559 | ||
560 | SENSE_CODE(0x5300, "Media load or eject failed") | |
561 | SENSE_CODE(0x5301, "Unload tape failure") | |
562 | SENSE_CODE(0x5302, "Medium removal prevented") | |
563 | SENSE_CODE(0x5303, "Medium removal prevented by data transfer element") | |
564 | SENSE_CODE(0x5304, "Medium thread or unthread failure") | |
565 | SENSE_CODE(0x5305, "Volume identifier invalid") | |
566 | SENSE_CODE(0x5306, "Volume identifier missing") | |
567 | SENSE_CODE(0x5307, "Duplicate volume identifier") | |
568 | SENSE_CODE(0x5308, "Element status unknown") | |
569 | SENSE_CODE(0x5309, "Data transfer device error - load failed") | |
570 | SENSE_CODE(0x530a, "Data transfer device error - unload failed") | |
571 | SENSE_CODE(0x530b, "Data transfer device error - unload missing") | |
572 | SENSE_CODE(0x530c, "Data transfer device error - eject failed") | |
573 | SENSE_CODE(0x530d, "Data transfer device error - library communication failed") | |
574 | ||
575 | SENSE_CODE(0x5400, "Scsi to host system interface failure") | |
576 | ||
577 | SENSE_CODE(0x5500, "System resource failure") | |
578 | SENSE_CODE(0x5501, "System buffer full") | |
579 | SENSE_CODE(0x5502, "Insufficient reservation resources") | |
580 | SENSE_CODE(0x5503, "Insufficient resources") | |
581 | SENSE_CODE(0x5504, "Insufficient registration resources") | |
582 | SENSE_CODE(0x5505, "Insufficient access control resources") | |
583 | SENSE_CODE(0x5506, "Auxiliary memory out of space") | |
584 | SENSE_CODE(0x5507, "Quota error") | |
585 | SENSE_CODE(0x5508, "Maximum number of supplemental decryption keys exceeded") | |
586 | SENSE_CODE(0x5509, "Medium auxiliary memory not accessible") | |
587 | SENSE_CODE(0x550A, "Data currently unavailable") | |
588 | SENSE_CODE(0x550B, "Insufficient power for operation") | |
589 | SENSE_CODE(0x550C, "Insufficient resources to create rod") | |
590 | SENSE_CODE(0x550D, "Insufficient resources to create rod token") | |
591 | SENSE_CODE(0x550E, "Insufficient zone resources") | |
592 | ||
593 | SENSE_CODE(0x5700, "Unable to recover table-of-contents") | |
594 | ||
595 | SENSE_CODE(0x5800, "Generation does not exist") | |
596 | ||
597 | SENSE_CODE(0x5900, "Updated block read") | |
598 | ||
599 | SENSE_CODE(0x5A00, "Operator request or state change input") | |
600 | SENSE_CODE(0x5A01, "Operator medium removal request") | |
601 | SENSE_CODE(0x5A02, "Operator selected write protect") | |
602 | SENSE_CODE(0x5A03, "Operator selected write permit") | |
603 | ||
604 | SENSE_CODE(0x5B00, "Log exception") | |
605 | SENSE_CODE(0x5B01, "Threshold condition met") | |
606 | SENSE_CODE(0x5B02, "Log counter at maximum") | |
607 | SENSE_CODE(0x5B03, "Log list codes exhausted") | |
608 | ||
609 | SENSE_CODE(0x5C00, "Rpl status change") | |
610 | SENSE_CODE(0x5C01, "Spindles synchronized") | |
611 | SENSE_CODE(0x5C02, "Spindles not synchronized") | |
612 | ||
613 | SENSE_CODE(0x5D00, "Failure prediction threshold exceeded") | |
614 | SENSE_CODE(0x5D01, "Media failure prediction threshold exceeded") | |
615 | SENSE_CODE(0x5D02, "Logical unit failure prediction threshold exceeded") | |
616 | SENSE_CODE(0x5D03, "Spare area exhaustion prediction threshold exceeded") | |
617 | SENSE_CODE(0x5D10, "Hardware impending failure general hard drive failure") | |
618 | SENSE_CODE(0x5D11, "Hardware impending failure drive error rate too high") | |
619 | SENSE_CODE(0x5D12, "Hardware impending failure data error rate too high") | |
620 | SENSE_CODE(0x5D13, "Hardware impending failure seek error rate too high") | |
621 | SENSE_CODE(0x5D14, "Hardware impending failure too many block reassigns") | |
622 | SENSE_CODE(0x5D15, "Hardware impending failure access times too high") | |
623 | SENSE_CODE(0x5D16, "Hardware impending failure start unit times too high") | |
624 | SENSE_CODE(0x5D17, "Hardware impending failure channel parametrics") | |
625 | SENSE_CODE(0x5D18, "Hardware impending failure controller detected") | |
626 | SENSE_CODE(0x5D19, "Hardware impending failure throughput performance") | |
627 | SENSE_CODE(0x5D1A, "Hardware impending failure seek time performance") | |
628 | SENSE_CODE(0x5D1B, "Hardware impending failure spin-up retry count") | |
629 | SENSE_CODE(0x5D1C, "Hardware impending failure drive calibration retry count") | |
630 | SENSE_CODE(0x5D20, "Controller impending failure general hard drive failure") | |
631 | SENSE_CODE(0x5D21, "Controller impending failure drive error rate too high") | |
632 | SENSE_CODE(0x5D22, "Controller impending failure data error rate too high") | |
633 | SENSE_CODE(0x5D23, "Controller impending failure seek error rate too high") | |
634 | SENSE_CODE(0x5D24, "Controller impending failure too many block reassigns") | |
635 | SENSE_CODE(0x5D25, "Controller impending failure access times too high") | |
636 | SENSE_CODE(0x5D26, "Controller impending failure start unit times too high") | |
637 | SENSE_CODE(0x5D27, "Controller impending failure channel parametrics") | |
638 | SENSE_CODE(0x5D28, "Controller impending failure controller detected") | |
639 | SENSE_CODE(0x5D29, "Controller impending failure throughput performance") | |
640 | SENSE_CODE(0x5D2A, "Controller impending failure seek time performance") | |
641 | SENSE_CODE(0x5D2B, "Controller impending failure spin-up retry count") | |
642 | SENSE_CODE(0x5D2C, "Controller impending failure drive calibration retry count") | |
643 | SENSE_CODE(0x5D30, "Data channel impending failure general hard drive failure") | |
644 | SENSE_CODE(0x5D31, "Data channel impending failure drive error rate too high") | |
645 | SENSE_CODE(0x5D32, "Data channel impending failure data error rate too high") | |
646 | SENSE_CODE(0x5D33, "Data channel impending failure seek error rate too high") | |
647 | SENSE_CODE(0x5D34, "Data channel impending failure too many block reassigns") | |
648 | SENSE_CODE(0x5D35, "Data channel impending failure access times too high") | |
649 | SENSE_CODE(0x5D36, "Data channel impending failure start unit times too high") | |
650 | SENSE_CODE(0x5D37, "Data channel impending failure channel parametrics") | |
651 | SENSE_CODE(0x5D38, "Data channel impending failure controller detected") | |
652 | SENSE_CODE(0x5D39, "Data channel impending failure throughput performance") | |
653 | SENSE_CODE(0x5D3A, "Data channel impending failure seek time performance") | |
654 | SENSE_CODE(0x5D3B, "Data channel impending failure spin-up retry count") | |
655 | SENSE_CODE(0x5D3C, "Data channel impending failure drive calibration retry count") | |
656 | SENSE_CODE(0x5D40, "Servo impending failure general hard drive failure") | |
657 | SENSE_CODE(0x5D41, "Servo impending failure drive error rate too high") | |
658 | SENSE_CODE(0x5D42, "Servo impending failure data error rate too high") | |
659 | SENSE_CODE(0x5D43, "Servo impending failure seek error rate too high") | |
660 | SENSE_CODE(0x5D44, "Servo impending failure too many block reassigns") | |
661 | SENSE_CODE(0x5D45, "Servo impending failure access times too high") | |
662 | SENSE_CODE(0x5D46, "Servo impending failure start unit times too high") | |
663 | SENSE_CODE(0x5D47, "Servo impending failure channel parametrics") | |
664 | SENSE_CODE(0x5D48, "Servo impending failure controller detected") | |
665 | SENSE_CODE(0x5D49, "Servo impending failure throughput performance") | |
666 | SENSE_CODE(0x5D4A, "Servo impending failure seek time performance") | |
667 | SENSE_CODE(0x5D4B, "Servo impending failure spin-up retry count") | |
668 | SENSE_CODE(0x5D4C, "Servo impending failure drive calibration retry count") | |
669 | SENSE_CODE(0x5D50, "Spindle impending failure general hard drive failure") | |
670 | SENSE_CODE(0x5D51, "Spindle impending failure drive error rate too high") | |
671 | SENSE_CODE(0x5D52, "Spindle impending failure data error rate too high") | |
672 | SENSE_CODE(0x5D53, "Spindle impending failure seek error rate too high") | |
673 | SENSE_CODE(0x5D54, "Spindle impending failure too many block reassigns") | |
674 | SENSE_CODE(0x5D55, "Spindle impending failure access times too high") | |
675 | SENSE_CODE(0x5D56, "Spindle impending failure start unit times too high") | |
676 | SENSE_CODE(0x5D57, "Spindle impending failure channel parametrics") | |
677 | SENSE_CODE(0x5D58, "Spindle impending failure controller detected") | |
678 | SENSE_CODE(0x5D59, "Spindle impending failure throughput performance") | |
679 | SENSE_CODE(0x5D5A, "Spindle impending failure seek time performance") | |
680 | SENSE_CODE(0x5D5B, "Spindle impending failure spin-up retry count") | |
681 | SENSE_CODE(0x5D5C, "Spindle impending failure drive calibration retry count") | |
682 | SENSE_CODE(0x5D60, "Firmware impending failure general hard drive failure") | |
683 | SENSE_CODE(0x5D61, "Firmware impending failure drive error rate too high") | |
684 | SENSE_CODE(0x5D62, "Firmware impending failure data error rate too high") | |
685 | SENSE_CODE(0x5D63, "Firmware impending failure seek error rate too high") | |
686 | SENSE_CODE(0x5D64, "Firmware impending failure too many block reassigns") | |
687 | SENSE_CODE(0x5D65, "Firmware impending failure access times too high") | |
688 | SENSE_CODE(0x5D66, "Firmware impending failure start unit times too high") | |
689 | SENSE_CODE(0x5D67, "Firmware impending failure channel parametrics") | |
690 | SENSE_CODE(0x5D68, "Firmware impending failure controller detected") | |
691 | SENSE_CODE(0x5D69, "Firmware impending failure throughput performance") | |
692 | SENSE_CODE(0x5D6A, "Firmware impending failure seek time performance") | |
693 | SENSE_CODE(0x5D6B, "Firmware impending failure spin-up retry count") | |
694 | SENSE_CODE(0x5D6C, "Firmware impending failure drive calibration retry count") | |
695 | SENSE_CODE(0x5DFF, "Failure prediction threshold exceeded (false)") | |
696 | ||
697 | SENSE_CODE(0x5E00, "Low power condition on") | |
698 | SENSE_CODE(0x5E01, "Idle condition activated by timer") | |
699 | SENSE_CODE(0x5E02, "Standby condition activated by timer") | |
700 | SENSE_CODE(0x5E03, "Idle condition activated by command") | |
701 | SENSE_CODE(0x5E04, "Standby condition activated by command") | |
702 | SENSE_CODE(0x5E05, "Idle_b condition activated by timer") | |
703 | SENSE_CODE(0x5E06, "Idle_b condition activated by command") | |
704 | SENSE_CODE(0x5E07, "Idle_c condition activated by timer") | |
705 | SENSE_CODE(0x5E08, "Idle_c condition activated by command") | |
706 | SENSE_CODE(0x5E09, "Standby_y condition activated by timer") | |
707 | SENSE_CODE(0x5E0A, "Standby_y condition activated by command") | |
708 | SENSE_CODE(0x5E41, "Power state change to active") | |
709 | SENSE_CODE(0x5E42, "Power state change to idle") | |
710 | SENSE_CODE(0x5E43, "Power state change to standby") | |
711 | SENSE_CODE(0x5E45, "Power state change to sleep") | |
712 | SENSE_CODE(0x5E47, "Power state change to device control") | |
713 | ||
714 | SENSE_CODE(0x6000, "Lamp failure") | |
715 | ||
716 | SENSE_CODE(0x6100, "Video acquisition error") | |
717 | SENSE_CODE(0x6101, "Unable to acquire video") | |
718 | SENSE_CODE(0x6102, "Out of focus") | |
719 | ||
720 | SENSE_CODE(0x6200, "Scan head positioning error") | |
721 | ||
722 | SENSE_CODE(0x6300, "End of user area encountered on this track") | |
723 | SENSE_CODE(0x6301, "Packet does not fit in available space") | |
724 | ||
725 | SENSE_CODE(0x6400, "Illegal mode for this track") | |
726 | SENSE_CODE(0x6401, "Invalid packet size") | |
727 | ||
728 | SENSE_CODE(0x6500, "Voltage fault") | |
729 | ||
730 | SENSE_CODE(0x6600, "Automatic document feeder cover up") | |
731 | SENSE_CODE(0x6601, "Automatic document feeder lift up") | |
732 | SENSE_CODE(0x6602, "Document jam in automatic document feeder") | |
733 | SENSE_CODE(0x6603, "Document miss feed automatic in document feeder") | |
734 | ||
735 | SENSE_CODE(0x6700, "Configuration failure") | |
736 | SENSE_CODE(0x6701, "Configuration of incapable logical units failed") | |
737 | SENSE_CODE(0x6702, "Add logical unit failed") | |
738 | SENSE_CODE(0x6703, "Modification of logical unit failed") | |
739 | SENSE_CODE(0x6704, "Exchange of logical unit failed") | |
740 | SENSE_CODE(0x6705, "Remove of logical unit failed") | |
741 | SENSE_CODE(0x6706, "Attachment of logical unit failed") | |
742 | SENSE_CODE(0x6707, "Creation of logical unit failed") | |
743 | SENSE_CODE(0x6708, "Assign failure occurred") | |
744 | SENSE_CODE(0x6709, "Multiply assigned logical unit") | |
745 | SENSE_CODE(0x670A, "Set target port groups command failed") | |
746 | SENSE_CODE(0x670B, "ATA device feature not enabled") | |
747 | ||
748 | SENSE_CODE(0x6800, "Logical unit not configured") | |
749 | SENSE_CODE(0x6801, "Subsidiary logical unit not configured") | |
750 | ||
751 | SENSE_CODE(0x6900, "Data loss on logical unit") | |
752 | SENSE_CODE(0x6901, "Multiple logical unit failures") | |
753 | SENSE_CODE(0x6902, "Parity/data mismatch") | |
754 | ||
755 | SENSE_CODE(0x6A00, "Informational, refer to log") | |
756 | ||
757 | SENSE_CODE(0x6B00, "State change has occurred") | |
758 | SENSE_CODE(0x6B01, "Redundancy level got better") | |
759 | SENSE_CODE(0x6B02, "Redundancy level got worse") | |
760 | ||
761 | SENSE_CODE(0x6C00, "Rebuild failure occurred") | |
762 | ||
763 | SENSE_CODE(0x6D00, "Recalculate failure occurred") | |
764 | ||
765 | SENSE_CODE(0x6E00, "Command to logical unit failed") | |
766 | ||
767 | SENSE_CODE(0x6F00, "Copy protection key exchange failure - authentication failure") | |
768 | SENSE_CODE(0x6F01, "Copy protection key exchange failure - key not present") | |
769 | SENSE_CODE(0x6F02, "Copy protection key exchange failure - key not established") | |
770 | SENSE_CODE(0x6F03, "Read of scrambled sector without authentication") | |
771 | SENSE_CODE(0x6F04, "Media region code is mismatched to logical unit region") | |
772 | SENSE_CODE(0x6F05, "Drive region must be permanent/region reset count error") | |
773 | SENSE_CODE(0x6F06, "Insufficient block count for binding nonce recording") | |
774 | SENSE_CODE(0x6F07, "Conflict in binding nonce recording") | |
775 | /* | |
776 | * SENSE_CODE(0x70NN, "Decompression exception short algorithm id of nn") | |
777 | */ | |
778 | SENSE_CODE(0x7100, "Decompression exception long algorithm id") | |
779 | ||
780 | SENSE_CODE(0x7200, "Session fixation error") | |
781 | SENSE_CODE(0x7201, "Session fixation error writing lead-in") | |
782 | SENSE_CODE(0x7202, "Session fixation error writing lead-out") | |
783 | SENSE_CODE(0x7203, "Session fixation error - incomplete track in session") | |
784 | SENSE_CODE(0x7204, "Empty or partially written reserved track") | |
785 | SENSE_CODE(0x7205, "No more track reservations allowed") | |
786 | SENSE_CODE(0x7206, "RMZ extension is not allowed") | |
787 | SENSE_CODE(0x7207, "No more test zone extensions are allowed") | |
788 | ||
789 | SENSE_CODE(0x7300, "Cd control error") | |
790 | SENSE_CODE(0x7301, "Power calibration area almost full") | |
791 | SENSE_CODE(0x7302, "Power calibration area is full") | |
792 | SENSE_CODE(0x7303, "Power calibration area error") | |
793 | SENSE_CODE(0x7304, "Program memory area update failure") | |
794 | SENSE_CODE(0x7305, "Program memory area is full") | |
795 | SENSE_CODE(0x7306, "RMA/PMA is almost full") | |
796 | SENSE_CODE(0x7310, "Current power calibration area almost full") | |
797 | SENSE_CODE(0x7311, "Current power calibration area is full") | |
798 | SENSE_CODE(0x7317, "RDZ is full") | |
799 | ||
800 | SENSE_CODE(0x7400, "Security error") | |
801 | SENSE_CODE(0x7401, "Unable to decrypt data") | |
802 | SENSE_CODE(0x7402, "Unencrypted data encountered while decrypting") | |
803 | SENSE_CODE(0x7403, "Incorrect data encryption key") | |
804 | SENSE_CODE(0x7404, "Cryptographic integrity validation failed") | |
805 | SENSE_CODE(0x7405, "Error decrypting data") | |
806 | SENSE_CODE(0x7406, "Unknown signature verification key") | |
807 | SENSE_CODE(0x7407, "Encryption parameters not useable") | |
808 | SENSE_CODE(0x7408, "Digital signature validation failure") | |
809 | SENSE_CODE(0x7409, "Encryption mode mismatch on read") | |
810 | SENSE_CODE(0x740A, "Encrypted block not raw read enabled") | |
811 | SENSE_CODE(0x740B, "Incorrect Encryption parameters") | |
812 | SENSE_CODE(0x740C, "Unable to decrypt parameter list") | |
813 | SENSE_CODE(0x740D, "Encryption algorithm disabled") | |
814 | SENSE_CODE(0x7410, "SA creation parameter value invalid") | |
815 | SENSE_CODE(0x7411, "SA creation parameter value rejected") | |
816 | SENSE_CODE(0x7412, "Invalid SA usage") | |
817 | SENSE_CODE(0x7421, "Data Encryption configuration prevented") | |
818 | SENSE_CODE(0x7430, "SA creation parameter not supported") | |
819 | SENSE_CODE(0x7440, "Authentication failed") | |
820 | SENSE_CODE(0x7461, "External data encryption key manager access error") | |
821 | SENSE_CODE(0x7462, "External data encryption key manager error") | |
822 | SENSE_CODE(0x7463, "External data encryption key not found") | |
823 | SENSE_CODE(0x7464, "External data encryption request not authorized") | |
824 | SENSE_CODE(0x746E, "External data encryption control timeout") | |
825 | SENSE_CODE(0x746F, "External data encryption control error") | |
826 | SENSE_CODE(0x7471, "Logical unit access not authorized") | |
827 | SENSE_CODE(0x7479, "Security conflict in translated device") |