Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * seagate.c Copyright (C) 1992, 1993 Drew Eckhardt | |
3 | * low level scsi driver for ST01/ST02, Future Domain TMC-885, | |
4 | * TMC-950 by Drew Eckhardt <drew@colorado.edu> | |
5 | * | |
6 | * Note : TMC-880 boards don't work because they have two bits in | |
7 | * the status register flipped, I'll fix this "RSN" | |
8 | * [why do I have strong feeling that above message is from 1993? :-) | |
9 | * pavel@ucw.cz] | |
10 | * | |
11 | * This card does all the I/O via memory mapped I/O, so there is no need | |
12 | * to check or allocate a region of the I/O address space. | |
13 | */ | |
14 | ||
15 | /* 1996 - to use new read{b,w,l}, write{b,w,l}, and phys_to_virt | |
16 | * macros, replaced assembler routines with C. There's probably a | |
17 | * performance hit, but I only have a cdrom and can't tell. Define | |
18 | * SEAGATE_USE_ASM if you want the old assembler code -- SJT | |
19 | * | |
20 | * 1998-jul-29 - created DPRINTK macros and made it work under | |
21 | * linux 2.1.112, simplified some #defines etc. <pavel@ucw.cz> | |
22 | * | |
23 | * Aug 2000 - aeb - deleted seagate_st0x_biosparam(). It would try to | |
24 | * read the physical disk geometry, a bad mistake. Of course it doesn't | |
25 | * matter much what geometry one invents, but on large disks it | |
26 | * returned 256 (or more) heads, causing all kind of failures. | |
27 | * Of course this means that people might see a different geometry now, | |
28 | * so boot parameters may be necessary in some cases. | |
29 | */ | |
30 | ||
31 | /* | |
32 | * Configuration : | |
33 | * To use without BIOS -DOVERRIDE=base_address -DCONTROLLER=FD or SEAGATE | |
34 | * -DIRQ will override the default of 5. | |
35 | * Note: You can now set these options from the kernel's "command line". | |
36 | * The syntax is: | |
37 | * | |
38 | * st0x=ADDRESS,IRQ (for a Seagate controller) | |
39 | * or: | |
40 | * tmc8xx=ADDRESS,IRQ (for a TMC-8xx or TMC-950 controller) | |
41 | * eg: | |
42 | * tmc8xx=0xC8000,15 | |
43 | * | |
44 | * will configure the driver for a TMC-8xx style controller using IRQ 15 | |
45 | * with a base address of 0xC8000. | |
46 | * | |
47 | * -DARBITRATE | |
48 | * Will cause the host adapter to arbitrate for the | |
49 | * bus for better SCSI-II compatibility, rather than just | |
50 | * waiting for BUS FREE and then doing its thing. Should | |
51 | * let us do one command per Lun when I integrate my | |
52 | * reorganization changes into the distribution sources. | |
53 | * | |
54 | * -DDEBUG=65535 | |
55 | * Will activate debug code. | |
56 | * | |
57 | * -DFAST or -DFAST32 | |
58 | * Will use blind transfers where possible | |
59 | * | |
60 | * -DPARITY | |
61 | * This will enable parity. | |
62 | * | |
63 | * -DSEAGATE_USE_ASM | |
64 | * Will use older seagate assembly code. should be (very small amount) | |
65 | * Faster. | |
66 | * | |
67 | * -DSLOW_RATE=50 | |
68 | * Will allow compatibility with broken devices that don't | |
69 | * handshake fast enough (ie, some CD ROM's) for the Seagate | |
70 | * code. | |
71 | * | |
72 | * 50 is some number, It will let you specify a default | |
73 | * transfer rate if handshaking isn't working correctly. | |
74 | * | |
75 | * -DOLDCNTDATASCEME There is a new sceme to set the CONTROL | |
76 | * and DATA reigsters which complies more closely | |
77 | * with the SCSI2 standard. This hopefully eliminates | |
78 | * the need to swap the order these registers are | |
79 | * 'messed' with. It makes the following two options | |
80 | * obsolete. To reenable the old sceme define this. | |
81 | * | |
82 | * The following to options are patches from the SCSI.HOWTO | |
83 | * | |
84 | * -DSWAPSTAT This will swap the definitions for STAT_MSG and STAT_CD. | |
85 | * | |
86 | * -DSWAPCNTDATA This will swap the order that seagate.c messes with | |
87 | * the CONTROL an DATA registers. | |
88 | */ | |
89 | ||
90 | #include <linux/module.h> | |
91 | #include <linux/interrupt.h> | |
92 | #include <linux/spinlock.h> | |
93 | #include <linux/signal.h> | |
94 | #include <linux/string.h> | |
95 | #include <linux/proc_fs.h> | |
96 | #include <linux/init.h> | |
97 | #include <linux/delay.h> | |
98 | #include <linux/blkdev.h> | |
99 | #include <linux/stat.h> | |
68b3aa7c | 100 | #include <linux/delay.h> |
1da177e4 LT |
101 | |
102 | #include <asm/io.h> | |
103 | #include <asm/system.h> | |
104 | #include <asm/uaccess.h> | |
105 | ||
106 | #include "scsi.h" | |
db9dff36 | 107 | #include <scsi/scsi_dbg.h> |
1da177e4 LT |
108 | #include <scsi/scsi_host.h> |
109 | #include "seagate.h" | |
110 | ||
111 | #include <scsi/scsi_ioctl.h> | |
112 | ||
113 | #ifdef DEBUG | |
114 | #define DPRINTK( when, msg... ) do { if ( (DEBUG & (when)) == (when) ) printk( msg ); } while (0) | |
115 | #else | |
116 | #define DPRINTK( when, msg... ) do { } while (0) | |
117 | #endif | |
118 | #define DANY( msg... ) DPRINTK( 0xffff, msg ); | |
119 | ||
120 | #ifndef IRQ | |
121 | #define IRQ 5 | |
122 | #endif | |
123 | ||
124 | #ifdef FAST32 | |
125 | #define FAST | |
126 | #endif | |
127 | ||
128 | #undef LINKED /* Linked commands are currently broken! */ | |
129 | ||
130 | #if defined(OVERRIDE) && !defined(CONTROLLER) | |
131 | #error Please use -DCONTROLLER=SEAGATE or -DCONTROLLER=FD to override controller type | |
132 | #endif | |
133 | ||
134 | #ifndef __i386__ | |
135 | #undef SEAGATE_USE_ASM | |
136 | #endif | |
137 | ||
138 | /* | |
139 | Thanks to Brian Antoine for the example code in his Messy-Loss ST-01 | |
140 | driver, and Mitsugu Suzuki for information on the ST-01 | |
141 | SCSI host. | |
142 | */ | |
143 | ||
144 | /* | |
145 | CONTROL defines | |
146 | */ | |
147 | ||
148 | #define CMD_RST 0x01 | |
149 | #define CMD_SEL 0x02 | |
150 | #define CMD_BSY 0x04 | |
151 | #define CMD_ATTN 0x08 | |
152 | #define CMD_START_ARB 0x10 | |
153 | #define CMD_EN_PARITY 0x20 | |
154 | #define CMD_INTR 0x40 | |
155 | #define CMD_DRVR_ENABLE 0x80 | |
156 | ||
157 | /* | |
158 | STATUS | |
159 | */ | |
160 | #ifdef SWAPSTAT | |
161 | #define STAT_MSG 0x08 | |
162 | #define STAT_CD 0x02 | |
163 | #else | |
164 | #define STAT_MSG 0x02 | |
165 | #define STAT_CD 0x08 | |
166 | #endif | |
167 | ||
168 | #define STAT_BSY 0x01 | |
169 | #define STAT_IO 0x04 | |
170 | #define STAT_REQ 0x10 | |
171 | #define STAT_SEL 0x20 | |
172 | #define STAT_PARITY 0x40 | |
173 | #define STAT_ARB_CMPL 0x80 | |
174 | ||
175 | /* | |
176 | REQUESTS | |
177 | */ | |
178 | ||
179 | #define REQ_MASK (STAT_CD | STAT_IO | STAT_MSG) | |
180 | #define REQ_DATAOUT 0 | |
181 | #define REQ_DATAIN STAT_IO | |
182 | #define REQ_CMDOUT STAT_CD | |
183 | #define REQ_STATIN (STAT_CD | STAT_IO) | |
184 | #define REQ_MSGOUT (STAT_MSG | STAT_CD) | |
185 | #define REQ_MSGIN (STAT_MSG | STAT_CD | STAT_IO) | |
186 | ||
187 | extern volatile int seagate_st0x_timeout; | |
188 | ||
189 | #ifdef PARITY | |
190 | #define BASE_CMD CMD_EN_PARITY | |
191 | #else | |
192 | #define BASE_CMD 0 | |
193 | #endif | |
194 | ||
195 | /* | |
196 | Debugging code | |
197 | */ | |
198 | ||
199 | #define PHASE_BUS_FREE 1 | |
200 | #define PHASE_ARBITRATION 2 | |
201 | #define PHASE_SELECTION 4 | |
202 | #define PHASE_DATAIN 8 | |
203 | #define PHASE_DATAOUT 0x10 | |
204 | #define PHASE_CMDOUT 0x20 | |
205 | #define PHASE_MSGIN 0x40 | |
206 | #define PHASE_MSGOUT 0x80 | |
207 | #define PHASE_STATUSIN 0x100 | |
208 | #define PHASE_ETC (PHASE_DATAIN | PHASE_DATAOUT | PHASE_CMDOUT | PHASE_MSGIN | PHASE_MSGOUT | PHASE_STATUSIN) | |
209 | #define PRINT_COMMAND 0x200 | |
210 | #define PHASE_EXIT 0x400 | |
211 | #define PHASE_RESELECT 0x800 | |
212 | #define DEBUG_FAST 0x1000 | |
213 | #define DEBUG_SG 0x2000 | |
214 | #define DEBUG_LINKED 0x4000 | |
215 | #define DEBUG_BORKEN 0x8000 | |
216 | ||
217 | /* | |
218 | * Control options - these are timeouts specified in .01 seconds. | |
219 | */ | |
220 | ||
221 | /* 30, 20 work */ | |
222 | #define ST0X_BUS_FREE_DELAY 25 | |
223 | #define ST0X_SELECTION_DELAY 25 | |
224 | ||
225 | #define SEAGATE 1 /* these determine the type of the controller */ | |
226 | #define FD 2 | |
227 | ||
228 | #define ST0X_ID_STR "Seagate ST-01/ST-02" | |
229 | #define FD_ID_STR "TMC-8XX/TMC-950" | |
230 | ||
231 | static int internal_command (unsigned char target, unsigned char lun, | |
232 | const void *cmnd, | |
233 | void *buff, int bufflen, int reselect); | |
234 | ||
235 | static int incommand; /* set if arbitration has finished | |
236 | and we are in some command phase. */ | |
237 | ||
238 | static unsigned int base_address = 0; /* Where the card ROM starts, used to | |
239 | calculate memory mapped register | |
240 | location. */ | |
241 | ||
242 | static void __iomem *st0x_cr_sr; /* control register write, status | |
243 | register read. 256 bytes in | |
244 | length. | |
245 | Read is status of SCSI BUS, as per | |
246 | STAT masks. */ | |
247 | ||
248 | static void __iomem *st0x_dr; /* data register, read write 256 | |
249 | bytes in length. */ | |
250 | ||
251 | static volatile int st0x_aborted = 0; /* set when we are aborted, ie by a | |
252 | time out, etc. */ | |
253 | ||
254 | static unsigned char controller_type = 0; /* set to SEAGATE for ST0x | |
255 | boards or FD for TMC-8xx | |
256 | boards */ | |
257 | static int irq = IRQ; | |
258 | ||
259 | module_param(base_address, uint, 0); | |
260 | module_param(controller_type, byte, 0); | |
261 | module_param(irq, int, 0); | |
262 | MODULE_LICENSE("GPL"); | |
263 | ||
264 | ||
265 | #define retcode(result) (((result) << 16) | (message << 8) | status) | |
266 | #define STATUS ((u8) readb(st0x_cr_sr)) | |
267 | #define DATA ((u8) readb(st0x_dr)) | |
268 | #define WRITE_CONTROL(d) { writeb((d), st0x_cr_sr); } | |
269 | #define WRITE_DATA(d) { writeb((d), st0x_dr); } | |
270 | ||
271 | #ifndef OVERRIDE | |
272 | static unsigned int seagate_bases[] = { | |
273 | 0xc8000, 0xca000, 0xcc000, | |
274 | 0xce000, 0xdc000, 0xde000 | |
275 | }; | |
276 | ||
277 | typedef struct { | |
278 | const unsigned char *signature; | |
279 | unsigned offset; | |
280 | unsigned length; | |
281 | unsigned char type; | |
282 | } Signature; | |
283 | ||
284 | static Signature __initdata signatures[] = { | |
285 | {"ST01 v1.7 (C) Copyright 1987 Seagate", 15, 37, SEAGATE}, | |
286 | {"SCSI BIOS 2.00 (C) Copyright 1987 Seagate", 15, 40, SEAGATE}, | |
287 | ||
288 | /* | |
289 | * The following two lines are NOT mistakes. One detects ROM revision | |
290 | * 3.0.0, the other 3.2. Since seagate has only one type of SCSI adapter, | |
291 | * and this is not going to change, the "SEAGATE" and "SCSI" together | |
292 | * are probably "good enough" | |
293 | */ | |
294 | ||
295 | {"SEAGATE SCSI BIOS ", 16, 17, SEAGATE}, | |
296 | {"SEAGATE SCSI BIOS ", 17, 17, SEAGATE}, | |
297 | ||
298 | /* | |
299 | * However, future domain makes several incompatible SCSI boards, so specific | |
300 | * signatures must be used. | |
301 | */ | |
302 | ||
303 | {"FUTURE DOMAIN CORP. (C) 1986-1989 V5.0C2/14/89", 5, 46, FD}, | |
304 | {"FUTURE DOMAIN CORP. (C) 1986-1989 V6.0A7/28/89", 5, 46, FD}, | |
305 | {"FUTURE DOMAIN CORP. (C) 1986-1990 V6.0105/31/90", 5, 47, FD}, | |
306 | {"FUTURE DOMAIN CORP. (C) 1986-1990 V6.0209/18/90", 5, 47, FD}, | |
307 | {"FUTURE DOMAIN CORP. (C) 1986-1990 V7.009/18/90", 5, 46, FD}, | |
308 | {"FUTURE DOMAIN CORP. (C) 1992 V8.00.004/02/92", 5, 44, FD}, | |
309 | {"IBM F1 BIOS V1.1004/30/92", 5, 25, FD}, | |
310 | {"FUTURE DOMAIN TMC-950", 5, 21, FD}, | |
311 | /* Added for 2.2.16 by Matthias_Heidbrink@b.maus.de */ | |
312 | {"IBM F1 V1.2009/22/93", 5, 25, FD}, | |
313 | }; | |
314 | ||
6391a113 | 315 | #define NUM_SIGNATURES ARRAY_SIZE(signatures) |
1da177e4 LT |
316 | #endif /* n OVERRIDE */ |
317 | ||
318 | /* | |
319 | * hostno stores the hostnumber, as told to us by the init routine. | |
320 | */ | |
321 | ||
322 | static int hostno = -1; | |
323 | static void seagate_reconnect_intr (int, void *, struct pt_regs *); | |
324 | static irqreturn_t do_seagate_reconnect_intr (int, void *, struct pt_regs *); | |
325 | ||
326 | #ifdef FAST | |
327 | static int fast = 1; | |
328 | #else | |
329 | #define fast 0 | |
330 | #endif | |
331 | ||
332 | #ifdef SLOW_RATE | |
333 | /* | |
334 | * Support for broken devices : | |
335 | * The Seagate board has a handshaking problem. Namely, a lack | |
336 | * thereof for slow devices. You can blast 600K/second through | |
337 | * it if you are polling for each byte, more if you do a blind | |
338 | * transfer. In the first case, with a fast device, REQ will | |
339 | * transition high-low or high-low-high before your loop restarts | |
340 | * and you'll have no problems. In the second case, the board | |
341 | * will insert wait states for up to 13.2 usecs for REQ to | |
342 | * transition low->high, and everything will work. | |
343 | * | |
344 | * However, there's nothing in the state machine that says | |
345 | * you *HAVE* to see a high-low-high set of transitions before | |
346 | * sending the next byte, and slow things like the Trantor CD ROMS | |
347 | * will break because of this. | |
348 | * | |
349 | * So, we need to slow things down, which isn't as simple as it | |
350 | * seems. We can't slow things down period, because then people | |
351 | * who don't recompile their kernels will shoot me for ruining | |
352 | * their performance. We need to do it on a case per case basis. | |
353 | * | |
354 | * The best for performance will be to, only for borken devices | |
355 | * (this is stored on a per-target basis in the scsi_devices array) | |
356 | * | |
357 | * Wait for a low->high transition before continuing with that | |
358 | * transfer. If we timeout, continue anyways. We don't need | |
359 | * a long timeout, because REQ should only be asserted until the | |
360 | * corresponding ACK is received and processed. | |
361 | * | |
362 | * Note that we can't use the system timer for this, because of | |
363 | * resolution, and we *really* can't use the timer chip since | |
364 | * gettimeofday() and the beeper routines use that. So, | |
365 | * the best thing for us to do will be to calibrate a timing | |
366 | * loop in the initialization code using the timer chip before | |
367 | * gettimeofday() can screw with it. | |
368 | * | |
369 | * FIXME: this is broken (not borken :-). Empty loop costs less than | |
370 | * loop with ISA access in it! -- pavel@ucw.cz | |
371 | */ | |
372 | ||
373 | static int borken_calibration = 0; | |
374 | ||
375 | static void __init borken_init (void) | |
376 | { | |
377 | register int count = 0, start = jiffies + 1, stop = start + 25; | |
378 | ||
379 | /* FIXME: There may be a better approach, this is a straight port for | |
380 | now */ | |
381 | preempt_disable(); | |
382 | while (time_before (jiffies, start)) | |
383 | cpu_relax(); | |
384 | for (; time_before (jiffies, stop); ++count) | |
385 | cpu_relax(); | |
386 | preempt_enable(); | |
387 | ||
388 | /* | |
389 | * Ok, we now have a count for .25 seconds. Convert to a | |
390 | * count per second and divide by transfer rate in K. */ | |
391 | ||
392 | borken_calibration = (count * 4) / (SLOW_RATE * 1024); | |
393 | ||
394 | if (borken_calibration < 1) | |
395 | borken_calibration = 1; | |
396 | } | |
397 | ||
398 | static inline void borken_wait (void) | |
399 | { | |
400 | register int count; | |
401 | ||
402 | for (count = borken_calibration; count && (STATUS & STAT_REQ); --count) | |
403 | cpu_relax(); | |
404 | ||
405 | #if (DEBUG & DEBUG_BORKEN) | |
406 | if (count) | |
407 | printk ("scsi%d : borken timeout\n", hostno); | |
408 | #endif | |
409 | } | |
410 | ||
411 | #endif /* def SLOW_RATE */ | |
412 | ||
413 | /* These beasts only live on ISA, and ISA means 8MHz. Each ULOOP() | |
414 | * contains at least one ISA access, which takes more than 0.125 | |
415 | * usec. So if we loop 8 times time in usec, we are safe. | |
416 | */ | |
417 | ||
418 | #define ULOOP( i ) for (clock = i*8;;) | |
419 | #define TIMEOUT (!(clock--)) | |
420 | ||
d0be4a7d | 421 | int __init seagate_st0x_detect (struct scsi_host_template * tpnt) |
1da177e4 LT |
422 | { |
423 | struct Scsi_Host *instance; | |
424 | int i, j; | |
425 | unsigned long cr, dr; | |
426 | ||
427 | tpnt->proc_name = "seagate"; | |
428 | /* | |
429 | * First, we try for the manual override. | |
430 | */ | |
431 | DANY ("Autodetecting ST0x / TMC-8xx\n"); | |
432 | ||
433 | if (hostno != -1) { | |
434 | printk (KERN_ERR "seagate_st0x_detect() called twice?!\n"); | |
435 | return 0; | |
436 | } | |
437 | ||
438 | /* If the user specified the controller type from the command line, | |
439 | controller_type will be non-zero, so don't try to detect one */ | |
440 | ||
441 | if (!controller_type) { | |
442 | #ifdef OVERRIDE | |
443 | base_address = OVERRIDE; | |
444 | controller_type = CONTROLLER; | |
445 | ||
446 | DANY ("Base address overridden to %x, controller type is %s\n", | |
447 | base_address, | |
448 | controller_type == SEAGATE ? "SEAGATE" : "FD"); | |
449 | #else /* OVERRIDE */ | |
450 | /* | |
451 | * To detect this card, we simply look for the signature | |
452 | * from the BIOS version notice in all the possible locations | |
453 | * of the ROM's. This has a nice side effect of not trashing | |
454 | * any register locations that might be used by something else. | |
455 | * | |
456 | * XXX - note that we probably should be probing the address | |
457 | * space for the on-board RAM instead. | |
458 | */ | |
459 | ||
6391a113 | 460 | for (i = 0; i < ARRAY_SIZE(seagate_bases); ++i) { |
1da177e4 LT |
461 | void __iomem *p = ioremap(seagate_bases[i], 0x2000); |
462 | if (!p) | |
463 | continue; | |
464 | for (j = 0; j < NUM_SIGNATURES; ++j) | |
465 | if (check_signature(p + signatures[j].offset, signatures[j].signature, signatures[j].length)) { | |
466 | base_address = seagate_bases[i]; | |
467 | controller_type = signatures[j].type; | |
468 | break; | |
469 | } | |
470 | iounmap(p); | |
471 | } | |
472 | #endif /* OVERRIDE */ | |
473 | } | |
474 | /* (! controller_type) */ | |
475 | tpnt->this_id = (controller_type == SEAGATE) ? 7 : 6; | |
476 | tpnt->name = (controller_type == SEAGATE) ? ST0X_ID_STR : FD_ID_STR; | |
477 | ||
478 | if (!base_address) { | |
479 | printk(KERN_INFO "seagate: ST0x/TMC-8xx not detected.\n"); | |
480 | return 0; | |
481 | } | |
482 | ||
483 | cr = base_address + (controller_type == SEAGATE ? 0x1a00 : 0x1c00); | |
484 | dr = cr + 0x200; | |
485 | st0x_cr_sr = ioremap(cr, 0x100); | |
486 | st0x_dr = ioremap(dr, 0x100); | |
487 | ||
488 | DANY("%s detected. Base address = %x, cr = %x, dr = %x\n", | |
489 | tpnt->name, base_address, cr, dr); | |
490 | ||
491 | /* | |
492 | * At all times, we will use IRQ 5. Should also check for IRQ3 | |
493 | * if we lose our first interrupt. | |
494 | */ | |
495 | instance = scsi_register (tpnt, 0); | |
496 | if (instance == NULL) | |
497 | return 0; | |
498 | ||
499 | hostno = instance->host_no; | |
1d6f359a | 500 | if (request_irq (irq, do_seagate_reconnect_intr, IRQF_DISABLED, (controller_type == SEAGATE) ? "seagate" : "tmc-8xx", instance)) { |
1da177e4 LT |
501 | printk(KERN_ERR "scsi%d : unable to allocate IRQ%d\n", hostno, irq); |
502 | return 0; | |
503 | } | |
504 | instance->irq = irq; | |
505 | instance->io_port = base_address; | |
506 | #ifdef SLOW_RATE | |
507 | printk(KERN_INFO "Calibrating borken timer... "); | |
508 | borken_init(); | |
509 | printk(" %d cycles per transfer\n", borken_calibration); | |
510 | #endif | |
511 | printk (KERN_INFO "This is one second... "); | |
512 | { | |
513 | int clock; | |
514 | ULOOP (1 * 1000 * 1000) { | |
515 | STATUS; | |
516 | if (TIMEOUT) | |
517 | break; | |
518 | } | |
519 | } | |
520 | ||
521 | printk ("done, %s options:" | |
522 | #ifdef ARBITRATE | |
523 | " ARBITRATE" | |
524 | #endif | |
525 | #ifdef DEBUG | |
526 | " DEBUG" | |
527 | #endif | |
528 | #ifdef FAST | |
529 | " FAST" | |
530 | #ifdef FAST32 | |
531 | "32" | |
532 | #endif | |
533 | #endif | |
534 | #ifdef LINKED | |
535 | " LINKED" | |
536 | #endif | |
537 | #ifdef PARITY | |
538 | " PARITY" | |
539 | #endif | |
540 | #ifdef SEAGATE_USE_ASM | |
541 | " SEAGATE_USE_ASM" | |
542 | #endif | |
543 | #ifdef SLOW_RATE | |
544 | " SLOW_RATE" | |
545 | #endif | |
546 | #ifdef SWAPSTAT | |
547 | " SWAPSTAT" | |
548 | #endif | |
549 | #ifdef SWAPCNTDATA | |
550 | " SWAPCNTDATA" | |
551 | #endif | |
552 | "\n", tpnt->name); | |
553 | return 1; | |
554 | } | |
555 | ||
556 | static const char *seagate_st0x_info (struct Scsi_Host *shpnt) | |
557 | { | |
558 | static char buffer[64]; | |
559 | ||
560 | snprintf(buffer, 64, "%s at irq %d, address 0x%05X", | |
561 | (controller_type == SEAGATE) ? ST0X_ID_STR : FD_ID_STR, | |
562 | irq, base_address); | |
563 | return buffer; | |
564 | } | |
565 | ||
566 | /* | |
567 | * These are our saved pointers for the outstanding command that is | |
568 | * waiting for a reconnect | |
569 | */ | |
570 | ||
571 | static unsigned char current_target, current_lun; | |
572 | static unsigned char *current_cmnd, *current_data; | |
573 | static int current_nobuffs; | |
574 | static struct scatterlist *current_buffer; | |
575 | static int current_bufflen; | |
576 | ||
577 | #ifdef LINKED | |
578 | /* | |
579 | * linked_connected indicates whether or not we are currently connected to | |
580 | * linked_target, linked_lun and in an INFORMATION TRANSFER phase, | |
581 | * using linked commands. | |
582 | */ | |
583 | ||
584 | static int linked_connected = 0; | |
585 | static unsigned char linked_target, linked_lun; | |
586 | #endif | |
587 | ||
588 | static void (*done_fn) (Scsi_Cmnd *) = NULL; | |
589 | static Scsi_Cmnd *SCint = NULL; | |
590 | ||
591 | /* | |
592 | * These control whether or not disconnect / reconnect will be attempted, | |
593 | * or are being attempted. | |
594 | */ | |
595 | ||
596 | #define NO_RECONNECT 0 | |
597 | #define RECONNECT_NOW 1 | |
598 | #define CAN_RECONNECT 2 | |
599 | ||
600 | /* | |
601 | * LINKED_RIGHT indicates that we are currently connected to the correct target | |
602 | * for this command, LINKED_WRONG indicates that we are connected to the wrong | |
603 | * target. Note that these imply CAN_RECONNECT and require defined(LINKED). | |
604 | */ | |
605 | ||
606 | #define LINKED_RIGHT 3 | |
607 | #define LINKED_WRONG 4 | |
608 | ||
609 | /* | |
610 | * This determines if we are expecting to reconnect or not. | |
611 | */ | |
612 | ||
613 | static int should_reconnect = 0; | |
614 | ||
615 | /* | |
616 | * The seagate_reconnect_intr routine is called when a target reselects the | |
617 | * host adapter. This occurs on the interrupt triggered by the target | |
618 | * asserting SEL. | |
619 | */ | |
620 | ||
621 | static irqreturn_t do_seagate_reconnect_intr(int irq, void *dev_id, | |
622 | struct pt_regs *regs) | |
623 | { | |
624 | unsigned long flags; | |
625 | struct Scsi_Host *dev = dev_id; | |
626 | ||
627 | spin_lock_irqsave (dev->host_lock, flags); | |
628 | seagate_reconnect_intr (irq, dev_id, regs); | |
629 | spin_unlock_irqrestore (dev->host_lock, flags); | |
630 | return IRQ_HANDLED; | |
631 | } | |
632 | ||
633 | static void seagate_reconnect_intr (int irq, void *dev_id, struct pt_regs *regs) | |
634 | { | |
635 | int temp; | |
636 | Scsi_Cmnd *SCtmp; | |
637 | ||
638 | DPRINTK (PHASE_RESELECT, "scsi%d : seagate_reconnect_intr() called\n", hostno); | |
639 | ||
640 | if (!should_reconnect) | |
641 | printk(KERN_WARNING "scsi%d: unexpected interrupt.\n", hostno); | |
642 | else { | |
643 | should_reconnect = 0; | |
644 | ||
645 | DPRINTK (PHASE_RESELECT, "scsi%d : internal_command(%d, %08x, %08x, RECONNECT_NOW\n", | |
646 | hostno, current_target, current_data, current_bufflen); | |
647 | ||
648 | temp = internal_command (current_target, current_lun, current_cmnd, current_data, current_bufflen, RECONNECT_NOW); | |
649 | ||
650 | if (msg_byte(temp) != DISCONNECT) { | |
651 | if (done_fn) { | |
652 | DPRINTK(PHASE_RESELECT, "scsi%d : done_fn(%d,%08x)", hostno, hostno, temp); | |
653 | if (!SCint) | |
654 | panic ("SCint == NULL in seagate"); | |
655 | SCtmp = SCint; | |
656 | SCint = NULL; | |
657 | SCtmp->result = temp; | |
658 | done_fn(SCtmp); | |
659 | } else | |
660 | printk(KERN_ERR "done_fn() not defined.\n"); | |
661 | } | |
662 | } | |
663 | } | |
664 | ||
665 | /* | |
666 | * The seagate_st0x_queue_command() function provides a queued interface | |
667 | * to the seagate SCSI driver. Basically, it just passes control onto the | |
668 | * seagate_command() function, after fixing it so that the done_fn() | |
669 | * is set to the one passed to the function. We have to be very careful, | |
670 | * because there are some commands on some devices that do not disconnect, | |
671 | * and if we simply call the done_fn when the command is done then another | |
672 | * command is started and queue_command is called again... We end up | |
673 | * overflowing the kernel stack, and this tends not to be such a good idea. | |
674 | */ | |
675 | ||
676 | static int recursion_depth = 0; | |
677 | ||
678 | static int seagate_st0x_queue_command (Scsi_Cmnd * SCpnt, void (*done) (Scsi_Cmnd *)) | |
679 | { | |
680 | int result, reconnect; | |
681 | Scsi_Cmnd *SCtmp; | |
682 | ||
683 | DANY ("seagate: que_command"); | |
684 | done_fn = done; | |
685 | current_target = SCpnt->device->id; | |
686 | current_lun = SCpnt->device->lun; | |
687 | current_cmnd = SCpnt->cmnd; | |
688 | current_data = (unsigned char *) SCpnt->request_buffer; | |
689 | current_bufflen = SCpnt->request_bufflen; | |
690 | SCint = SCpnt; | |
691 | if (recursion_depth) | |
692 | return 1; | |
693 | recursion_depth++; | |
694 | do { | |
695 | #ifdef LINKED | |
696 | /* | |
697 | * Set linked command bit in control field of SCSI command. | |
698 | */ | |
699 | ||
700 | current_cmnd[SCpnt->cmd_len] |= 0x01; | |
701 | if (linked_connected) { | |
702 | DPRINTK (DEBUG_LINKED, "scsi%d : using linked commands, current I_T_L nexus is ", hostno); | |
703 | if (linked_target == current_target && linked_lun == current_lun) | |
704 | { | |
705 | DPRINTK(DEBUG_LINKED, "correct\n"); | |
706 | reconnect = LINKED_RIGHT; | |
707 | } else { | |
708 | DPRINTK(DEBUG_LINKED, "incorrect\n"); | |
709 | reconnect = LINKED_WRONG; | |
710 | } | |
711 | } else | |
712 | #endif /* LINKED */ | |
713 | reconnect = CAN_RECONNECT; | |
714 | ||
715 | result = internal_command(SCint->device->id, SCint->device->lun, SCint->cmnd, | |
716 | SCint->request_buffer, SCint->request_bufflen, reconnect); | |
717 | if (msg_byte(result) == DISCONNECT) | |
718 | break; | |
719 | SCtmp = SCint; | |
720 | SCint = NULL; | |
721 | SCtmp->result = result; | |
722 | done_fn(SCtmp); | |
723 | } | |
724 | while (SCint); | |
725 | recursion_depth--; | |
726 | return 0; | |
727 | } | |
728 | ||
729 | static int internal_command (unsigned char target, unsigned char lun, | |
730 | const void *cmnd, void *buff, int bufflen, int reselect) | |
731 | { | |
732 | unsigned char *data = NULL; | |
733 | struct scatterlist *buffer = NULL; | |
734 | int clock, temp, nobuffs = 0, done = 0, len = 0; | |
735 | #ifdef DEBUG | |
736 | int transfered = 0, phase = 0, newphase; | |
737 | #endif | |
738 | register unsigned char status_read; | |
739 | unsigned char tmp_data, tmp_control, status = 0, message = 0; | |
740 | unsigned transfersize = 0, underflow = 0; | |
741 | #ifdef SLOW_RATE | |
742 | int borken = (int) SCint->device->borken; /* Does the current target require | |
743 | Very Slow I/O ? */ | |
744 | #endif | |
745 | ||
746 | incommand = 0; | |
747 | st0x_aborted = 0; | |
748 | ||
749 | #if (DEBUG & PRINT_COMMAND) | |
750 | printk("scsi%d : target = %d, command = ", hostno, target); | |
db9dff36 | 751 | __scsi_print_command((unsigned char *) cmnd); |
1da177e4 LT |
752 | #endif |
753 | ||
754 | #if (DEBUG & PHASE_RESELECT) | |
755 | switch (reselect) { | |
756 | case RECONNECT_NOW: | |
757 | printk("scsi%d : reconnecting\n", hostno); | |
758 | break; | |
759 | #ifdef LINKED | |
760 | case LINKED_RIGHT: | |
761 | printk("scsi%d : connected, can reconnect\n", hostno); | |
762 | break; | |
763 | case LINKED_WRONG: | |
764 | printk("scsi%d : connected to wrong target, can reconnect\n", | |
765 | hostno); | |
766 | break; | |
767 | #endif | |
768 | case CAN_RECONNECT: | |
769 | printk("scsi%d : allowed to reconnect\n", hostno); | |
770 | break; | |
771 | default: | |
772 | printk("scsi%d : not allowed to reconnect\n", hostno); | |
773 | } | |
774 | #endif | |
775 | ||
776 | if (target == (controller_type == SEAGATE ? 7 : 6)) | |
777 | return DID_BAD_TARGET; | |
778 | ||
779 | /* | |
780 | * We work it differently depending on if this is is "the first time," | |
781 | * or a reconnect. If this is a reselect phase, then SEL will | |
782 | * be asserted, and we must skip selection / arbitration phases. | |
783 | */ | |
784 | ||
785 | switch (reselect) { | |
786 | case RECONNECT_NOW: | |
787 | DPRINTK (PHASE_RESELECT, "scsi%d : phase RESELECT \n", hostno); | |
788 | /* | |
789 | * At this point, we should find the logical or of our ID | |
790 | * and the original target's ID on the BUS, with BSY, SEL, | |
791 | * and I/O signals asserted. | |
792 | * | |
793 | * After ARBITRATION phase is completed, only SEL, BSY, | |
794 | * and the target ID are asserted. A valid initiator ID | |
795 | * is not on the bus until IO is asserted, so we must wait | |
796 | * for that. | |
797 | */ | |
798 | ULOOP (100 * 1000) { | |
799 | temp = STATUS; | |
800 | if ((temp & STAT_IO) && !(temp & STAT_BSY)) | |
801 | break; | |
802 | if (TIMEOUT) { | |
803 | DPRINTK (PHASE_RESELECT, "scsi%d : RESELECT timed out while waiting for IO .\n", hostno); | |
804 | return (DID_BAD_INTR << 16); | |
805 | } | |
806 | } | |
807 | ||
808 | /* | |
809 | * After I/O is asserted by the target, we can read our ID | |
810 | * and its ID off of the BUS. | |
811 | */ | |
812 | ||
813 | if (!((temp = DATA) & (controller_type == SEAGATE ? 0x80 : 0x40))) { | |
814 | DPRINTK (PHASE_RESELECT, "scsi%d : detected reconnect request to different target.\n\tData bus = %d\n", hostno, temp); | |
815 | return (DID_BAD_INTR << 16); | |
816 | } | |
817 | ||
818 | if (!(temp & (1 << current_target))) { | |
819 | printk(KERN_WARNING "scsi%d : Unexpected reselect interrupt. Data bus = %d\n", hostno, temp); | |
820 | return (DID_BAD_INTR << 16); | |
821 | } | |
822 | ||
823 | buffer = current_buffer; | |
824 | cmnd = current_cmnd; /* WDE add */ | |
825 | data = current_data; /* WDE add */ | |
826 | len = current_bufflen; /* WDE add */ | |
827 | nobuffs = current_nobuffs; | |
828 | ||
829 | /* | |
830 | * We have determined that we have been selected. At this | |
831 | * point, we must respond to the reselection by asserting | |
832 | * BSY ourselves | |
833 | */ | |
834 | ||
835 | #if 1 | |
836 | WRITE_CONTROL (BASE_CMD | CMD_DRVR_ENABLE | CMD_BSY); | |
837 | #else | |
838 | WRITE_CONTROL (BASE_CMD | CMD_BSY); | |
839 | #endif | |
840 | ||
841 | /* | |
842 | * The target will drop SEL, and raise BSY, at which time | |
843 | * we must drop BSY. | |
844 | */ | |
845 | ||
846 | ULOOP (100 * 1000) { | |
847 | if (!(STATUS & STAT_SEL)) | |
848 | break; | |
849 | if (TIMEOUT) { | |
850 | WRITE_CONTROL (BASE_CMD | CMD_INTR); | |
851 | DPRINTK (PHASE_RESELECT, "scsi%d : RESELECT timed out while waiting for SEL.\n", hostno); | |
852 | return (DID_BAD_INTR << 16); | |
853 | } | |
854 | } | |
855 | WRITE_CONTROL (BASE_CMD); | |
856 | /* | |
857 | * At this point, we have connected with the target | |
858 | * and can get on with our lives. | |
859 | */ | |
860 | break; | |
861 | case CAN_RECONNECT: | |
862 | #ifdef LINKED | |
863 | /* | |
864 | * This is a bletcherous hack, just as bad as the Unix #! | |
865 | * interpreter stuff. If it turns out we are using the wrong | |
866 | * I_T_L nexus, the easiest way to deal with it is to go into | |
867 | * our INFORMATION TRANSFER PHASE code, send a ABORT | |
868 | * message on MESSAGE OUT phase, and then loop back to here. | |
869 | */ | |
870 | connect_loop: | |
871 | #endif | |
872 | DPRINTK (PHASE_BUS_FREE, "scsi%d : phase = BUS FREE \n", hostno); | |
873 | ||
874 | /* | |
875 | * BUS FREE PHASE | |
876 | * | |
877 | * On entry, we make sure that the BUS is in a BUS FREE | |
878 | * phase, by insuring that both BSY and SEL are low for | |
879 | * at least one bus settle delay. Several reads help | |
880 | * eliminate wire glitch. | |
881 | */ | |
882 | ||
883 | #ifndef ARBITRATE | |
884 | #error FIXME: this is broken: we may not use jiffies here - we are under cli(). It will hardlock. | |
885 | clock = jiffies + ST0X_BUS_FREE_DELAY; | |
886 | ||
887 | while (((STATUS | STATUS | STATUS) & (STAT_BSY | STAT_SEL)) && (!st0x_aborted) && time_before (jiffies, clock)) | |
888 | cpu_relax(); | |
889 | ||
890 | if (time_after (jiffies, clock)) | |
891 | return retcode (DID_BUS_BUSY); | |
892 | else if (st0x_aborted) | |
893 | return retcode (st0x_aborted); | |
894 | #endif | |
895 | DPRINTK (PHASE_SELECTION, "scsi%d : phase = SELECTION\n", hostno); | |
896 | ||
897 | clock = jiffies + ST0X_SELECTION_DELAY; | |
898 | ||
899 | /* | |
900 | * Arbitration/selection procedure : | |
901 | * 1. Disable drivers | |
902 | * 2. Write HOST adapter address bit | |
903 | * 3. Set start arbitration. | |
904 | * 4. We get either ARBITRATION COMPLETE or SELECT at this | |
905 | * point. | |
906 | * 5. OR our ID and targets on bus. | |
907 | * 6. Enable SCSI drivers and asserted SEL and ATTN | |
908 | */ | |
909 | ||
910 | #ifdef ARBITRATE | |
911 | /* FIXME: verify host lock is always held here */ | |
912 | WRITE_CONTROL(0); | |
913 | WRITE_DATA((controller_type == SEAGATE) ? 0x80 : 0x40); | |
914 | WRITE_CONTROL(CMD_START_ARB); | |
915 | ||
916 | ULOOP (ST0X_SELECTION_DELAY * 10000) { | |
917 | status_read = STATUS; | |
918 | if (status_read & STAT_ARB_CMPL) | |
919 | break; | |
920 | if (st0x_aborted) /* FIXME: What? We are going to do something even after abort? */ | |
921 | break; | |
922 | if (TIMEOUT || (status_read & STAT_SEL)) { | |
923 | printk(KERN_WARNING "scsi%d : arbitration lost or timeout.\n", hostno); | |
924 | WRITE_CONTROL (BASE_CMD); | |
925 | return retcode (DID_NO_CONNECT); | |
926 | } | |
927 | } | |
928 | DPRINTK (PHASE_SELECTION, "scsi%d : arbitration complete\n", hostno); | |
929 | #endif | |
930 | ||
931 | /* | |
932 | * When the SCSI device decides that we're gawking at it, | |
933 | * it will respond by asserting BUSY on the bus. | |
934 | * | |
935 | * Note : the Seagate ST-01/02 product manual says that we | |
936 | * should twiddle the DATA register before the control | |
937 | * register. However, this does not work reliably so we do | |
938 | * it the other way around. | |
939 | * | |
940 | * Probably could be a problem with arbitration too, we | |
941 | * really should try this with a SCSI protocol or logic | |
942 | * analyzer to see what is going on. | |
943 | */ | |
944 | tmp_data = (unsigned char) ((1 << target) | (controller_type == SEAGATE ? 0x80 : 0x40)); | |
945 | tmp_control = BASE_CMD | CMD_DRVR_ENABLE | CMD_SEL | (reselect ? CMD_ATTN : 0); | |
946 | ||
947 | /* FIXME: verify host lock is always held here */ | |
948 | #ifdef OLDCNTDATASCEME | |
949 | #ifdef SWAPCNTDATA | |
950 | WRITE_CONTROL (tmp_control); | |
951 | WRITE_DATA (tmp_data); | |
952 | #else | |
953 | WRITE_DATA (tmp_data); | |
954 | WRITE_CONTROL (tmp_control); | |
955 | #endif | |
956 | #else | |
957 | tmp_control ^= CMD_BSY; /* This is guesswork. What used to be in driver */ | |
958 | WRITE_CONTROL (tmp_control); /* could never work: it sent data into control */ | |
959 | WRITE_DATA (tmp_data); /* register and control info into data. Hopefully */ | |
960 | tmp_control ^= CMD_BSY; /* fixed, but order of first two may be wrong. */ | |
961 | WRITE_CONTROL (tmp_control); /* -- pavel@ucw.cz */ | |
962 | #endif | |
963 | ||
964 | ULOOP (250 * 1000) { | |
965 | if (st0x_aborted) { | |
966 | /* | |
967 | * If we have been aborted, and we have a | |
968 | * command in progress, IE the target | |
969 | * still has BSY asserted, then we will | |
970 | * reset the bus, and notify the midlevel | |
971 | * driver to expect sense. | |
972 | */ | |
973 | ||
974 | WRITE_CONTROL (BASE_CMD); | |
975 | if (STATUS & STAT_BSY) { | |
976 | printk(KERN_WARNING "scsi%d : BST asserted after we've been aborted.\n", hostno); | |
977 | seagate_st0x_bus_reset(NULL); | |
978 | return retcode (DID_RESET); | |
979 | } | |
980 | return retcode (st0x_aborted); | |
981 | } | |
982 | if (STATUS & STAT_BSY) | |
983 | break; | |
984 | if (TIMEOUT) { | |
985 | DPRINTK (PHASE_SELECTION, "scsi%d : NO CONNECT with target %d, stat = %x \n", hostno, target, STATUS); | |
986 | return retcode (DID_NO_CONNECT); | |
987 | } | |
988 | } | |
989 | ||
990 | /* Establish current pointers. Take into account scatter / gather */ | |
991 | ||
992 | if ((nobuffs = SCint->use_sg)) { | |
993 | #if (DEBUG & DEBUG_SG) | |
994 | { | |
995 | int i; | |
996 | printk("scsi%d : scatter gather requested, using %d buffers.\n", hostno, nobuffs); | |
997 | for (i = 0; i < nobuffs; ++i) | |
998 | printk("scsi%d : buffer %d address = %p length = %d\n", | |
999 | hostno, i, | |
1000 | page_address(buffer[i].page) + buffer[i].offset, | |
1001 | buffer[i].length); | |
1002 | } | |
1003 | #endif | |
1004 | ||
79bd3f85 | 1005 | buffer = (struct scatterlist *) SCint->request_buffer; |
1da177e4 LT |
1006 | len = buffer->length; |
1007 | data = page_address(buffer->page) + buffer->offset; | |
1008 | } else { | |
1009 | DPRINTK (DEBUG_SG, "scsi%d : scatter gather not requested.\n", hostno); | |
1010 | buffer = NULL; | |
1011 | len = SCint->request_bufflen; | |
1012 | data = (unsigned char *) SCint->request_buffer; | |
1013 | } | |
1014 | ||
1015 | DPRINTK (PHASE_DATAIN | PHASE_DATAOUT, "scsi%d : len = %d\n", | |
1016 | hostno, len); | |
1017 | ||
1018 | break; | |
1019 | #ifdef LINKED | |
1020 | case LINKED_RIGHT: | |
1021 | break; | |
1022 | case LINKED_WRONG: | |
1023 | break; | |
1024 | #endif | |
1025 | } /* end of switch(reselect) */ | |
1026 | ||
1027 | /* | |
1028 | * There are several conditions under which we wish to send a message : | |
1029 | * 1. When we are allowing disconnect / reconnect, and need to | |
1030 | * establish the I_T_L nexus via an IDENTIFY with the DiscPriv bit | |
1031 | * set. | |
1032 | * | |
1033 | * 2. When we are doing linked commands, are have the wrong I_T_L | |
1034 | * nexus established and want to send an ABORT message. | |
1035 | */ | |
1036 | ||
1037 | /* GCC does not like an ifdef inside a macro, so do it the hard way. */ | |
1038 | #ifdef LINKED | |
1039 | WRITE_CONTROL (BASE_CMD | CMD_DRVR_ENABLE | (((reselect == CAN_RECONNECT)|| (reselect == LINKED_WRONG))? CMD_ATTN : 0)); | |
1040 | #else | |
1041 | WRITE_CONTROL (BASE_CMD | CMD_DRVR_ENABLE | (((reselect == CAN_RECONNECT))? CMD_ATTN : 0)); | |
1042 | #endif | |
1043 | ||
1044 | /* | |
1045 | * INFORMATION TRANSFER PHASE | |
1046 | * | |
1047 | * The nasty looking read / write inline assembler loops we use for | |
1048 | * DATAIN and DATAOUT phases are approximately 4-5 times as fast as | |
1049 | * the 'C' versions - since we're moving 1024 bytes of data, this | |
1050 | * really adds up. | |
1051 | * | |
1052 | * SJT: The nasty-looking assembler is gone, so it's slower. | |
1053 | * | |
1054 | */ | |
1055 | ||
1056 | DPRINTK (PHASE_ETC, "scsi%d : phase = INFORMATION TRANSFER\n", hostno); | |
1057 | ||
1058 | incommand = 1; | |
1059 | transfersize = SCint->transfersize; | |
1060 | underflow = SCint->underflow; | |
1061 | ||
1062 | /* | |
1063 | * Now, we poll the device for status information, | |
1064 | * and handle any requests it makes. Note that since we are unsure | |
1065 | * of how much data will be flowing across the system, etc and | |
1066 | * cannot make reasonable timeouts, that we will instead have the | |
1067 | * midlevel driver handle any timeouts that occur in this phase. | |
1068 | */ | |
1069 | ||
1070 | while (((status_read = STATUS) & STAT_BSY) && !st0x_aborted && !done) { | |
1071 | #ifdef PARITY | |
1072 | if (status_read & STAT_PARITY) { | |
1073 | printk(KERN_ERR "scsi%d : got parity error\n", hostno); | |
1074 | st0x_aborted = DID_PARITY; | |
1075 | } | |
1076 | #endif | |
1077 | if (status_read & STAT_REQ) { | |
1078 | #if ((DEBUG & PHASE_ETC) == PHASE_ETC) | |
1079 | if ((newphase = (status_read & REQ_MASK)) != phase) { | |
1080 | phase = newphase; | |
1081 | switch (phase) { | |
1082 | case REQ_DATAOUT: | |
1083 | printk ("scsi%d : phase = DATA OUT\n", hostno); | |
1084 | break; | |
1085 | case REQ_DATAIN: | |
1086 | printk ("scsi%d : phase = DATA IN\n", hostno); | |
1087 | break; | |
1088 | case REQ_CMDOUT: | |
1089 | printk | |
1090 | ("scsi%d : phase = COMMAND OUT\n", hostno); | |
1091 | break; | |
1092 | case REQ_STATIN: | |
1093 | printk ("scsi%d : phase = STATUS IN\n", hostno); | |
1094 | break; | |
1095 | case REQ_MSGOUT: | |
1096 | printk | |
1097 | ("scsi%d : phase = MESSAGE OUT\n", hostno); | |
1098 | break; | |
1099 | case REQ_MSGIN: | |
1100 | printk ("scsi%d : phase = MESSAGE IN\n", hostno); | |
1101 | break; | |
1102 | default: | |
1103 | printk ("scsi%d : phase = UNKNOWN\n", hostno); | |
1104 | st0x_aborted = DID_ERROR; | |
1105 | } | |
1106 | } | |
1107 | #endif | |
1108 | switch (status_read & REQ_MASK) { | |
1109 | case REQ_DATAOUT: | |
1110 | /* | |
1111 | * If we are in fast mode, then we simply splat | |
1112 | * the data out in word-sized chunks as fast as | |
1113 | * we can. | |
1114 | */ | |
1115 | ||
1116 | if (!len) { | |
1117 | #if 0 | |
1118 | printk("scsi%d: underflow to target %d lun %d \n", hostno, target, lun); | |
1119 | st0x_aborted = DID_ERROR; | |
1120 | fast = 0; | |
1121 | #endif | |
1122 | break; | |
1123 | } | |
1124 | ||
1125 | if (fast && transfersize | |
1126 | && !(len % transfersize) | |
1127 | && (len >= transfersize) | |
1128 | #ifdef FAST32 | |
1129 | && !(transfersize % 4) | |
1130 | #endif | |
1131 | ) { | |
1132 | DPRINTK (DEBUG_FAST, | |
1133 | "scsi%d : FAST transfer, underflow = %d, transfersize = %d\n" | |
1134 | " len = %d, data = %08x\n", | |
1135 | hostno, SCint->underflow, | |
1136 | SCint->transfersize, len, | |
1137 | data); | |
1138 | ||
1139 | /* SJT: Start. Fast Write */ | |
1140 | #ifdef SEAGATE_USE_ASM | |
1141 | __asm__ ("cld\n\t" | |
1142 | #ifdef FAST32 | |
1143 | "shr $2, %%ecx\n\t" | |
1144 | "1:\t" | |
1145 | "lodsl\n\t" | |
1146 | "movl %%eax, (%%edi)\n\t" | |
1147 | #else | |
1148 | "1:\t" | |
1149 | "lodsb\n\t" | |
1150 | "movb %%al, (%%edi)\n\t" | |
1151 | #endif | |
1152 | "loop 1b;" | |
1153 | /* output */ : | |
1154 | /* input */ :"D" (st0x_dr), | |
1155 | "S" | |
1156 | (data), | |
1157 | "c" (SCint->transfersize) | |
1158 | /* clobbered */ | |
1159 | : "eax", "ecx", | |
1160 | "esi"); | |
1161 | #else /* SEAGATE_USE_ASM */ | |
1162 | memcpy_toio(st0x_dr, data, transfersize); | |
1163 | #endif /* SEAGATE_USE_ASM */ | |
1164 | /* SJT: End */ | |
1165 | len -= transfersize; | |
1166 | data += transfersize; | |
1167 | DPRINTK (DEBUG_FAST, "scsi%d : FAST transfer complete len = %d data = %08x\n", hostno, len, data); | |
1168 | } else { | |
1169 | /* | |
1170 | * We loop as long as we are in a | |
1171 | * data out phase, there is data to | |
1172 | * send, and BSY is still active. | |
1173 | */ | |
1174 | ||
1175 | /* SJT: Start. Slow Write. */ | |
1176 | #ifdef SEAGATE_USE_ASM | |
1177 | ||
1178 | int __dummy_1, __dummy_2; | |
1179 | ||
1180 | /* | |
1181 | * We loop as long as we are in a data out phase, there is data to send, | |
1182 | * and BSY is still active. | |
1183 | */ | |
1184 | /* Local variables : len = ecx , data = esi, | |
1185 | st0x_cr_sr = ebx, st0x_dr = edi | |
1186 | */ | |
1187 | __asm__ ( | |
1188 | /* Test for any data here at all. */ | |
1189 | "orl %%ecx, %%ecx\n\t" | |
1190 | "jz 2f\n\t" "cld\n\t" | |
1191 | /* "movl st0x_cr_sr, %%ebx\n\t" */ | |
1192 | /* "movl st0x_dr, %%edi\n\t" */ | |
1193 | "1:\t" | |
1194 | "movb (%%ebx), %%al\n\t" | |
1195 | /* Test for BSY */ | |
1196 | "test $1, %%al\n\t" | |
1197 | "jz 2f\n\t" | |
1198 | /* Test for data out phase - STATUS & REQ_MASK should be | |
1199 | REQ_DATAOUT, which is 0. */ | |
1200 | "test $0xe, %%al\n\t" | |
1201 | "jnz 2f\n\t" | |
1202 | /* Test for REQ */ | |
1203 | "test $0x10, %%al\n\t" | |
1204 | "jz 1b\n\t" | |
1205 | "lodsb\n\t" | |
1206 | "movb %%al, (%%edi)\n\t" | |
1207 | "loop 1b\n\t" "2:\n" | |
1208 | /* output */ :"=S" (data), "=c" (len), | |
1209 | "=b" | |
1210 | (__dummy_1), | |
1211 | "=D" (__dummy_2) | |
1212 | /* input */ | |
1213 | : "0" (data), "1" (len), | |
1214 | "2" (st0x_cr_sr), | |
1215 | "3" (st0x_dr) | |
1216 | /* clobbered */ | |
1217 | : "eax"); | |
1218 | #else /* SEAGATE_USE_ASM */ | |
1219 | while (len) { | |
1220 | unsigned char stat; | |
1221 | ||
1222 | stat = STATUS; | |
1223 | if (!(stat & STAT_BSY) | |
1224 | || ((stat & REQ_MASK) != | |
1225 | REQ_DATAOUT)) | |
1226 | break; | |
1227 | if (stat & STAT_REQ) { | |
1228 | WRITE_DATA (*data++); | |
1229 | --len; | |
1230 | } | |
1231 | } | |
1232 | #endif /* SEAGATE_USE_ASM */ | |
1233 | /* SJT: End. */ | |
1234 | } | |
1235 | ||
1236 | if (!len && nobuffs) { | |
1237 | --nobuffs; | |
1238 | ++buffer; | |
1239 | len = buffer->length; | |
1240 | data = page_address(buffer->page) + buffer->offset; | |
1241 | DPRINTK (DEBUG_SG, | |
1242 | "scsi%d : next scatter-gather buffer len = %d address = %08x\n", | |
1243 | hostno, len, data); | |
1244 | } | |
1245 | break; | |
1246 | ||
1247 | case REQ_DATAIN: | |
1248 | #ifdef SLOW_RATE | |
1249 | if (borken) { | |
1250 | #if (DEBUG & (PHASE_DATAIN)) | |
1251 | transfered += len; | |
1252 | #endif | |
1253 | for (; len && (STATUS & (REQ_MASK | STAT_REQ)) == (REQ_DATAIN | STAT_REQ); --len) { | |
1254 | *data++ = DATA; | |
1255 | borken_wait(); | |
1256 | } | |
1257 | #if (DEBUG & (PHASE_DATAIN)) | |
1258 | transfered -= len; | |
1259 | #endif | |
1260 | } else | |
1261 | #endif | |
1262 | ||
1263 | if (fast && transfersize | |
1264 | && !(len % transfersize) | |
1265 | && (len >= transfersize) | |
1266 | #ifdef FAST32 | |
1267 | && !(transfersize % 4) | |
1268 | #endif | |
1269 | ) { | |
1270 | DPRINTK (DEBUG_FAST, | |
1271 | "scsi%d : FAST transfer, underflow = %d, transfersize = %d\n" | |
1272 | " len = %d, data = %08x\n", | |
1273 | hostno, SCint->underflow, | |
1274 | SCint->transfersize, len, | |
1275 | data); | |
1276 | ||
1277 | /* SJT: Start. Fast Read */ | |
1278 | #ifdef SEAGATE_USE_ASM | |
1279 | __asm__ ("cld\n\t" | |
1280 | #ifdef FAST32 | |
1281 | "shr $2, %%ecx\n\t" | |
1282 | "1:\t" | |
1283 | "movl (%%esi), %%eax\n\t" | |
1284 | "stosl\n\t" | |
1285 | #else | |
1286 | "1:\t" | |
1287 | "movb (%%esi), %%al\n\t" | |
1288 | "stosb\n\t" | |
1289 | #endif | |
1290 | "loop 1b\n\t" | |
1291 | /* output */ : | |
1292 | /* input */ :"S" (st0x_dr), | |
1293 | "D" | |
1294 | (data), | |
1295 | "c" (SCint->transfersize) | |
1296 | /* clobbered */ | |
1297 | : "eax", "ecx", | |
1298 | "edi"); | |
1299 | #else /* SEAGATE_USE_ASM */ | |
1300 | memcpy_fromio(data, st0x_dr, len); | |
1301 | #endif /* SEAGATE_USE_ASM */ | |
1302 | /* SJT: End */ | |
1303 | len -= transfersize; | |
1304 | data += transfersize; | |
1305 | #if (DEBUG & PHASE_DATAIN) | |
1306 | printk ("scsi%d: transfered += %d\n", hostno, transfersize); | |
1307 | transfered += transfersize; | |
1308 | #endif | |
1309 | ||
1310 | DPRINTK (DEBUG_FAST, "scsi%d : FAST transfer complete len = %d data = %08x\n", hostno, len, data); | |
1311 | } else { | |
1312 | ||
1313 | #if (DEBUG & PHASE_DATAIN) | |
1314 | printk ("scsi%d: transfered += %d\n", hostno, len); | |
1315 | transfered += len; /* Assume we'll transfer it all, then | |
1316 | subtract what we *didn't* transfer */ | |
1317 | #endif | |
1318 | ||
1319 | /* | |
1320 | * We loop as long as we are in a data in phase, there is room to read, | |
1321 | * and BSY is still active | |
1322 | */ | |
1323 | ||
1324 | /* SJT: Start. */ | |
1325 | #ifdef SEAGATE_USE_ASM | |
1326 | ||
1327 | int __dummy_3, __dummy_4; | |
1328 | ||
1329 | /* Dummy clobbering variables for the new gcc-2.95 */ | |
1330 | ||
1331 | /* | |
1332 | * We loop as long as we are in a data in phase, there is room to read, | |
1333 | * and BSY is still active | |
1334 | */ | |
1335 | /* Local variables : ecx = len, edi = data | |
1336 | esi = st0x_cr_sr, ebx = st0x_dr */ | |
1337 | __asm__ ( | |
1338 | /* Test for room to read */ | |
1339 | "orl %%ecx, %%ecx\n\t" | |
1340 | "jz 2f\n\t" "cld\n\t" | |
1341 | /* "movl st0x_cr_sr, %%esi\n\t" */ | |
1342 | /* "movl st0x_dr, %%ebx\n\t" */ | |
1343 | "1:\t" | |
1344 | "movb (%%esi), %%al\n\t" | |
1345 | /* Test for BSY */ | |
1346 | "test $1, %%al\n\t" | |
1347 | "jz 2f\n\t" | |
1348 | /* Test for data in phase - STATUS & REQ_MASK should be REQ_DATAIN, | |
1349 | = STAT_IO, which is 4. */ | |
1350 | "movb $0xe, %%ah\n\t" | |
1351 | "andb %%al, %%ah\n\t" | |
1352 | "cmpb $0x04, %%ah\n\t" | |
1353 | "jne 2f\n\t" | |
1354 | /* Test for REQ */ | |
1355 | "test $0x10, %%al\n\t" | |
1356 | "jz 1b\n\t" | |
1357 | "movb (%%ebx), %%al\n\t" | |
1358 | "stosb\n\t" | |
1359 | "loop 1b\n\t" "2:\n" | |
1360 | /* output */ :"=D" (data), "=c" (len), | |
1361 | "=S" | |
1362 | (__dummy_3), | |
1363 | "=b" (__dummy_4) | |
1364 | /* input */ | |
1365 | : "0" (data), "1" (len), | |
1366 | "2" (st0x_cr_sr), | |
1367 | "3" (st0x_dr) | |
1368 | /* clobbered */ | |
1369 | : "eax"); | |
1370 | #else /* SEAGATE_USE_ASM */ | |
1371 | while (len) { | |
1372 | unsigned char stat; | |
1373 | ||
1374 | stat = STATUS; | |
1375 | if (!(stat & STAT_BSY) | |
1376 | || ((stat & REQ_MASK) != | |
1377 | REQ_DATAIN)) | |
1378 | break; | |
1379 | if (stat & STAT_REQ) { | |
1380 | *data++ = DATA; | |
1381 | --len; | |
1382 | } | |
1383 | } | |
1384 | #endif /* SEAGATE_USE_ASM */ | |
1385 | /* SJT: End. */ | |
1386 | #if (DEBUG & PHASE_DATAIN) | |
1387 | printk ("scsi%d: transfered -= %d\n", hostno, len); | |
1388 | transfered -= len; /* Since we assumed all of Len got * | |
1389 | transfered, correct our mistake */ | |
1390 | #endif | |
1391 | } | |
1392 | ||
1393 | if (!len && nobuffs) { | |
1394 | --nobuffs; | |
1395 | ++buffer; | |
1396 | len = buffer->length; | |
1397 | data = page_address(buffer->page) + buffer->offset; | |
1398 | DPRINTK (DEBUG_SG, "scsi%d : next scatter-gather buffer len = %d address = %08x\n", hostno, len, data); | |
1399 | } | |
1400 | break; | |
1401 | ||
1402 | case REQ_CMDOUT: | |
1403 | while (((status_read = STATUS) & STAT_BSY) && | |
1404 | ((status_read & REQ_MASK) == REQ_CMDOUT)) | |
1405 | if (status_read & STAT_REQ) { | |
1406 | WRITE_DATA (*(const unsigned char *) cmnd); | |
1407 | cmnd = 1 + (const unsigned char *)cmnd; | |
1408 | #ifdef SLOW_RATE | |
1409 | if (borken) | |
1410 | borken_wait (); | |
1411 | #endif | |
1412 | } | |
1413 | break; | |
1414 | ||
1415 | case REQ_STATIN: | |
1416 | status = DATA; | |
1417 | break; | |
1418 | ||
1419 | case REQ_MSGOUT: | |
1420 | /* | |
1421 | * We can only have sent a MSG OUT if we | |
1422 | * requested to do this by raising ATTN. | |
1423 | * So, we must drop ATTN. | |
1424 | */ | |
1425 | WRITE_CONTROL (BASE_CMD | CMD_DRVR_ENABLE); | |
1426 | /* | |
1427 | * If we are reconnecting, then we must | |
1428 | * send an IDENTIFY message in response | |
1429 | * to MSGOUT. | |
1430 | */ | |
1431 | switch (reselect) { | |
1432 | case CAN_RECONNECT: | |
1433 | WRITE_DATA (IDENTIFY (1, lun)); | |
1434 | DPRINTK (PHASE_RESELECT | PHASE_MSGOUT, "scsi%d : sent IDENTIFY message.\n", hostno); | |
1435 | break; | |
1436 | #ifdef LINKED | |
1437 | case LINKED_WRONG: | |
1438 | WRITE_DATA (ABORT); | |
1439 | linked_connected = 0; | |
1440 | reselect = CAN_RECONNECT; | |
1441 | goto connect_loop; | |
1442 | DPRINTK (PHASE_MSGOUT | DEBUG_LINKED, "scsi%d : sent ABORT message to cancel incorrect I_T_L nexus.\n", hostno); | |
1443 | #endif /* LINKED */ | |
1444 | DPRINTK (DEBUG_LINKED, "correct\n"); | |
1445 | default: | |
1446 | WRITE_DATA (NOP); | |
1447 | printk("scsi%d : target %d requested MSGOUT, sent NOP message.\n", hostno, target); | |
1448 | } | |
1449 | break; | |
1450 | ||
1451 | case REQ_MSGIN: | |
1452 | switch (message = DATA) { | |
1453 | case DISCONNECT: | |
1454 | DANY("seagate: deciding to disconnect\n"); | |
1455 | should_reconnect = 1; | |
1456 | current_data = data; /* WDE add */ | |
1457 | current_buffer = buffer; | |
1458 | current_bufflen = len; /* WDE add */ | |
1459 | current_nobuffs = nobuffs; | |
1460 | #ifdef LINKED | |
1461 | linked_connected = 0; | |
1462 | #endif | |
1463 | done = 1; | |
1464 | DPRINTK ((PHASE_RESELECT | PHASE_MSGIN), "scsi%d : disconnected.\n", hostno); | |
1465 | break; | |
1466 | ||
1467 | #ifdef LINKED | |
1468 | case LINKED_CMD_COMPLETE: | |
1469 | case LINKED_FLG_CMD_COMPLETE: | |
1470 | #endif | |
1471 | case COMMAND_COMPLETE: | |
1472 | /* | |
1473 | * Note : we should check for underflow here. | |
1474 | */ | |
1475 | DPRINTK(PHASE_MSGIN, "scsi%d : command complete.\n", hostno); | |
1476 | done = 1; | |
1477 | break; | |
1478 | case ABORT: | |
1479 | DPRINTK(PHASE_MSGIN, "scsi%d : abort message.\n", hostno); | |
1480 | done = 1; | |
1481 | break; | |
1482 | case SAVE_POINTERS: | |
1483 | current_buffer = buffer; | |
1484 | current_bufflen = len; /* WDE add */ | |
1485 | current_data = data; /* WDE mod */ | |
1486 | current_nobuffs = nobuffs; | |
1487 | DPRINTK (PHASE_MSGIN, "scsi%d : pointers saved.\n", hostno); | |
1488 | break; | |
1489 | case RESTORE_POINTERS: | |
1490 | buffer = current_buffer; | |
1491 | cmnd = current_cmnd; | |
1492 | data = current_data; /* WDE mod */ | |
1493 | len = current_bufflen; | |
1494 | nobuffs = current_nobuffs; | |
1495 | DPRINTK(PHASE_MSGIN, "scsi%d : pointers restored.\n", hostno); | |
1496 | break; | |
1497 | default: | |
1498 | ||
1499 | /* | |
1500 | * IDENTIFY distinguishes itself | |
1501 | * from the other messages by | |
1502 | * setting the high bit. | |
1503 | * | |
1504 | * Note : we need to handle at | |
1505 | * least one outstanding command | |
1506 | * per LUN, and need to hash the | |
1507 | * SCSI command for that I_T_L | |
1508 | * nexus based on the known ID | |
1509 | * (at this point) and LUN. | |
1510 | */ | |
1511 | ||
1512 | if (message & 0x80) { | |
1513 | DPRINTK (PHASE_MSGIN, "scsi%d : IDENTIFY message received from id %d, lun %d.\n", hostno, target, message & 7); | |
1514 | } else { | |
1515 | /* | |
1516 | * We should go into a | |
1517 | * MESSAGE OUT phase, and | |
1518 | * send a MESSAGE_REJECT | |
1519 | * if we run into a message | |
1520 | * that we don't like. The | |
1521 | * seagate driver needs | |
1522 | * some serious | |
1523 | * restructuring first | |
1524 | * though. | |
1525 | */ | |
1526 | DPRINTK (PHASE_MSGIN, "scsi%d : unknown message %d from target %d.\n", hostno, message, target); | |
1527 | } | |
1528 | } | |
1529 | break; | |
1530 | default: | |
1531 | printk(KERN_ERR "scsi%d : unknown phase.\n", hostno); | |
1532 | st0x_aborted = DID_ERROR; | |
1533 | } /* end of switch (status_read & REQ_MASK) */ | |
1534 | #ifdef SLOW_RATE | |
1535 | /* | |
1536 | * I really don't care to deal with borken devices in | |
1537 | * each single byte transfer case (ie, message in, | |
1538 | * message out, status), so I'll do the wait here if | |
1539 | * necessary. | |
1540 | */ | |
1541 | if(borken) | |
1542 | borken_wait(); | |
1543 | #endif | |
1544 | ||
1545 | } /* if(status_read & STAT_REQ) ends */ | |
1546 | } /* while(((status_read = STATUS)...) ends */ | |
1547 | ||
1548 | DPRINTK(PHASE_DATAIN | PHASE_DATAOUT | PHASE_EXIT, "scsi%d : Transfered %d bytes\n", hostno, transfered); | |
1549 | ||
1550 | #if (DEBUG & PHASE_EXIT) | |
1551 | #if 0 /* Doesn't work for scatter/gather */ | |
1552 | printk("Buffer : \n"); | |
1553 | for(i = 0; i < 20; ++i) | |
1554 | printk("%02x ", ((unsigned char *) data)[i]); /* WDE mod */ | |
1555 | printk("\n"); | |
1556 | #endif | |
1557 | printk("scsi%d : status = ", hostno); | |
db9dff36 | 1558 | scsi_print_status(status); |
1da177e4 LT |
1559 | printk(" message = %02x\n", message); |
1560 | #endif | |
1561 | ||
1562 | /* We shouldn't reach this until *after* BSY has been deasserted */ | |
1563 | ||
1564 | #ifdef LINKED | |
1565 | else | |
1566 | { | |
1567 | /* | |
1568 | * Fix the message byte so that unsuspecting high level drivers | |
1569 | * don't puke when they see a LINKED COMMAND message in place of | |
1570 | * the COMMAND COMPLETE they may be expecting. Shouldn't be | |
1571 | * necessary, but it's better to be on the safe side. | |
1572 | * | |
1573 | * A non LINKED* message byte will indicate that the command | |
1574 | * completed, and we are now disconnected. | |
1575 | */ | |
1576 | ||
1577 | switch (message) { | |
1578 | case LINKED_CMD_COMPLETE: | |
1579 | case LINKED_FLG_CMD_COMPLETE: | |
1580 | message = COMMAND_COMPLETE; | |
1581 | linked_target = current_target; | |
1582 | linked_lun = current_lun; | |
1583 | linked_connected = 1; | |
1584 | DPRINTK (DEBUG_LINKED, "scsi%d : keeping I_T_L nexus established for linked command.\n", hostno); | |
1585 | /* We also will need to adjust status to accommodate intermediate | |
1586 | conditions. */ | |
1587 | if ((status == INTERMEDIATE_GOOD) || (status == INTERMEDIATE_C_GOOD)) | |
1588 | status = GOOD; | |
1589 | break; | |
1590 | /* | |
1591 | * We should also handle what are "normal" termination | |
1592 | * messages here (ABORT, BUS_DEVICE_RESET?, and | |
1593 | * COMMAND_COMPLETE individually, and flake if things | |
1594 | * aren't right. | |
1595 | */ | |
1596 | default: | |
1597 | DPRINTK (DEBUG_LINKED, "scsi%d : closing I_T_L nexus.\n", hostno); | |
1598 | linked_connected = 0; | |
1599 | } | |
1600 | } | |
1601 | #endif /* LINKED */ | |
1602 | ||
1603 | if (should_reconnect) { | |
1604 | DPRINTK (PHASE_RESELECT, "scsi%d : exiting seagate_st0x_queue_command() with reconnect enabled.\n", hostno); | |
1605 | WRITE_CONTROL (BASE_CMD | CMD_INTR); | |
1606 | } else | |
1607 | WRITE_CONTROL (BASE_CMD); | |
1608 | ||
1609 | return retcode (st0x_aborted); | |
1610 | } /* end of internal_command */ | |
1611 | ||
1612 | static int seagate_st0x_abort (Scsi_Cmnd * SCpnt) | |
1613 | { | |
1614 | st0x_aborted = DID_ABORT; | |
1615 | return SUCCESS; | |
1616 | } | |
1617 | ||
1618 | #undef ULOOP | |
1619 | #undef TIMEOUT | |
1620 | ||
1621 | /* | |
1622 | * the seagate_st0x_reset function resets the SCSI bus | |
1623 | * | |
1624 | * May be called with SCpnt = NULL | |
1625 | */ | |
1626 | ||
1627 | static int seagate_st0x_bus_reset(Scsi_Cmnd * SCpnt) | |
1628 | { | |
1629 | /* No timeouts - this command is going to fail because it was reset. */ | |
1630 | DANY ("scsi%d: Reseting bus... ", hostno); | |
1631 | ||
1632 | /* assert RESET signal on SCSI bus. */ | |
1633 | WRITE_CONTROL (BASE_CMD | CMD_RST); | |
1634 | ||
68b3aa7c | 1635 | mdelay (20); |
1da177e4 LT |
1636 | |
1637 | WRITE_CONTROL (BASE_CMD); | |
1638 | st0x_aborted = DID_RESET; | |
1639 | ||
1640 | DANY ("done.\n"); | |
1641 | return SUCCESS; | |
1642 | } | |
1643 | ||
1da177e4 LT |
1644 | static int seagate_st0x_release(struct Scsi_Host *shost) |
1645 | { | |
1646 | if (shost->irq) | |
1647 | free_irq(shost->irq, shost); | |
1648 | release_region(shost->io_port, shost->n_io_port); | |
1649 | return 0; | |
1650 | } | |
1651 | ||
d0be4a7d | 1652 | static struct scsi_host_template driver_template = { |
1da177e4 LT |
1653 | .detect = seagate_st0x_detect, |
1654 | .release = seagate_st0x_release, | |
1655 | .info = seagate_st0x_info, | |
1656 | .queuecommand = seagate_st0x_queue_command, | |
1657 | .eh_abort_handler = seagate_st0x_abort, | |
1658 | .eh_bus_reset_handler = seagate_st0x_bus_reset, | |
1da177e4 LT |
1659 | .can_queue = 1, |
1660 | .this_id = 7, | |
1661 | .sg_tablesize = SG_ALL, | |
1662 | .cmd_per_lun = 1, | |
1663 | .use_clustering = DISABLE_CLUSTERING, | |
1664 | }; | |
1665 | #include "scsi_module.c" |