Commit | Line | Data |
---|---|---|
b2441318 | 1 | /* SPDX-License-Identifier: GPL-2.0 */ |
1da177e4 LT |
2 | /* |
3 | * mesh.h: definitions for the driver for the MESH SCSI bus adaptor | |
4 | * (Macintosh Enhanced SCSI Hardware) found on Power Macintosh computers. | |
5 | * | |
6 | * Copyright (C) 1996 Paul Mackerras. | |
7 | */ | |
8 | #ifndef _MESH_H | |
9 | #define _MESH_H | |
10 | ||
57cbd78e BVA |
11 | struct mesh_cmd_priv { |
12 | struct scsi_pointer scsi_pointer; | |
13 | }; | |
14 | ||
15 | static inline struct scsi_pointer *mesh_scsi_pointer(struct scsi_cmnd *cmd) | |
16 | { | |
17 | struct mesh_cmd_priv *mcmd = scsi_cmd_priv(cmd); | |
18 | ||
19 | return &mcmd->scsi_pointer; | |
20 | } | |
21 | ||
1da177e4 LT |
22 | /* |
23 | * Registers in the MESH controller. | |
24 | */ | |
25 | ||
26 | struct mesh_regs { | |
27 | unsigned char count_lo; | |
28 | char pad0[15]; | |
29 | unsigned char count_hi; | |
30 | char pad1[15]; | |
31 | unsigned char fifo; | |
32 | char pad2[15]; | |
33 | unsigned char sequence; | |
34 | char pad3[15]; | |
35 | unsigned char bus_status0; | |
36 | char pad4[15]; | |
37 | unsigned char bus_status1; | |
38 | char pad5[15]; | |
39 | unsigned char fifo_count; | |
40 | char pad6[15]; | |
41 | unsigned char exception; | |
42 | char pad7[15]; | |
43 | unsigned char error; | |
44 | char pad8[15]; | |
45 | unsigned char intr_mask; | |
46 | char pad9[15]; | |
47 | unsigned char interrupt; | |
48 | char pad10[15]; | |
49 | unsigned char source_id; | |
50 | char pad11[15]; | |
51 | unsigned char dest_id; | |
52 | char pad12[15]; | |
53 | unsigned char sync_params; | |
54 | char pad13[15]; | |
55 | unsigned char mesh_id; | |
56 | char pad14[15]; | |
57 | unsigned char sel_timeout; | |
58 | char pad15[15]; | |
59 | }; | |
60 | ||
61 | /* Bits in the sequence register. */ | |
62 | #define SEQ_DMA_MODE 0x80 /* use DMA for data transfer */ | |
63 | #define SEQ_TARGET 0x40 /* put the controller into target mode */ | |
64 | #define SEQ_ATN 0x20 /* assert ATN signal */ | |
65 | #define SEQ_ACTIVE_NEG 0x10 /* use active negation on REQ/ACK */ | |
66 | #define SEQ_CMD 0x0f /* command bits: */ | |
67 | #define SEQ_ARBITRATE 1 /* get the bus */ | |
68 | #define SEQ_SELECT 2 /* select a target */ | |
69 | #define SEQ_COMMAND 3 /* send a command */ | |
70 | #define SEQ_STATUS 4 /* receive status */ | |
71 | #define SEQ_DATAOUT 5 /* send data */ | |
72 | #define SEQ_DATAIN 6 /* receive data */ | |
73 | #define SEQ_MSGOUT 7 /* send a message */ | |
74 | #define SEQ_MSGIN 8 /* receive a message */ | |
75 | #define SEQ_BUSFREE 9 /* look for bus free */ | |
76 | #define SEQ_ENBPARITY 0x0a /* enable parity checking */ | |
77 | #define SEQ_DISPARITY 0x0b /* disable parity checking */ | |
78 | #define SEQ_ENBRESEL 0x0c /* enable reselection */ | |
79 | #define SEQ_DISRESEL 0x0d /* disable reselection */ | |
80 | #define SEQ_RESETMESH 0x0e /* reset the controller */ | |
81 | #define SEQ_FLUSHFIFO 0x0f /* clear out the FIFO */ | |
82 | ||
83 | /* Bits in the bus_status0 and bus_status1 registers: | |
84 | these correspond directly to the SCSI bus control signals. */ | |
85 | #define BS0_REQ 0x20 | |
86 | #define BS0_ACK 0x10 | |
87 | #define BS0_ATN 0x08 | |
88 | #define BS0_MSG 0x04 | |
89 | #define BS0_CD 0x02 | |
90 | #define BS0_IO 0x01 | |
91 | #define BS1_RST 0x80 | |
92 | #define BS1_BSY 0x40 | |
93 | #define BS1_SEL 0x20 | |
94 | ||
95 | /* Bus phases defined by the bits in bus_status0 */ | |
96 | #define BS0_PHASE (BS0_MSG+BS0_CD+BS0_IO) | |
97 | #define BP_DATAOUT 0 | |
98 | #define BP_DATAIN BS0_IO | |
99 | #define BP_COMMAND BS0_CD | |
100 | #define BP_STATUS (BS0_CD+BS0_IO) | |
101 | #define BP_MSGOUT (BS0_MSG+BS0_CD) | |
102 | #define BP_MSGIN (BS0_MSG+BS0_CD+BS0_IO) | |
103 | ||
104 | /* Bits in the exception register. */ | |
105 | #define EXC_SELWATN 0x20 /* (as target) we were selected with ATN */ | |
106 | #define EXC_SELECTED 0x10 /* (as target) we were selected w/o ATN */ | |
107 | #define EXC_RESELECTED 0x08 /* (as initiator) we were reselected */ | |
108 | #define EXC_ARBLOST 0x04 /* we lost arbitration */ | |
109 | #define EXC_PHASEMM 0x02 /* SCSI phase mismatch */ | |
110 | #define EXC_SELTO 0x01 /* selection timeout */ | |
111 | ||
112 | /* Bits in the error register */ | |
113 | #define ERR_UNEXPDISC 0x40 /* target unexpectedly disconnected */ | |
114 | #define ERR_SCSIRESET 0x20 /* SCSI bus got reset on us */ | |
115 | #define ERR_SEQERR 0x10 /* we did something the chip didn't like */ | |
116 | #define ERR_PARITY 0x01 /* parity error was detected */ | |
117 | ||
118 | /* Bits in the interrupt and intr_mask registers */ | |
119 | #define INT_ERROR 0x04 /* error interrupt */ | |
120 | #define INT_EXCEPTION 0x02 /* exception interrupt */ | |
121 | #define INT_CMDDONE 0x01 /* command done interrupt */ | |
122 | ||
123 | /* Fields in the sync_params register */ | |
124 | #define SYNC_OFF(x) ((x) >> 4) /* offset field */ | |
125 | #define SYNC_PER(x) ((x) & 0xf) /* period field */ | |
126 | #define SYNC_PARAMS(o, p) (((o) << 4) | (p)) | |
127 | #define ASYNC_PARAMS 2 /* sync_params value for async xfers */ | |
128 | ||
129 | /* | |
130 | * Assuming a clock frequency of 50MHz: | |
131 | * | |
132 | * The transfer period with SYNC_PER(sync_params) == x | |
133 | * is (x + 2) * 40ns, except that x == 0 gives 100ns. | |
134 | * | |
135 | * The units of the sel_timeout register are 10ms. | |
136 | */ | |
137 | ||
138 | ||
139 | #endif /* _MESH_H */ |