Commit | Line | Data |
---|---|---|
74ba9207 | 1 | // SPDX-License-Identifier: GPL-2.0-or-later |
1da177e4 LT |
2 | |
3 | /* NCR (or Symbios) 53c700 and 53c700-66 Driver | |
4 | * | |
5 | * Copyright (C) 2001 by James.Bottomley@HansenPartnership.com | |
6 | **----------------------------------------------------------------------------- | |
7 | ** | |
1da177e4 LT |
8 | ** |
9 | **----------------------------------------------------------------------------- | |
10 | */ | |
11 | ||
12 | /* Notes: | |
13 | * | |
14 | * This driver is designed exclusively for these chips (virtually the | |
15 | * earliest of the scripts engine chips). They need their own drivers | |
16 | * because they are missing so many of the scripts and snazzy register | |
17 | * features of their elder brothers (the 710, 720 and 770). | |
18 | * | |
19 | * The 700 is the lowliest of the line, it can only do async SCSI. | |
20 | * The 700-66 can at least do synchronous SCSI up to 10MHz. | |
21 | * | |
22 | * The 700 chip has no host bus interface logic of its own. However, | |
23 | * it is usually mapped to a location with well defined register | |
24 | * offsets. Therefore, if you can determine the base address and the | |
25 | * irq your board incorporating this chip uses, you can probably use | |
26 | * this driver to run it (although you'll probably have to write a | |
27 | * minimal wrapper for the purpose---see the NCR_D700 driver for | |
28 | * details about how to do this). | |
29 | * | |
30 | * | |
31 | * TODO List: | |
32 | * | |
33 | * 1. Better statistics in the proc fs | |
34 | * | |
35 | * 2. Implement message queue (queues SCSI messages like commands) and make | |
36 | * the abort and device reset functions use them. | |
37 | * */ | |
38 | ||
39 | /* CHANGELOG | |
40 | * | |
41 | * Version 2.8 | |
42 | * | |
43 | * Fixed bad bug affecting tag starvation processing (previously the | |
44 | * driver would hang the system if too many tags starved. Also fixed | |
45 | * bad bug having to do with 10 byte command processing and REQUEST | |
46 | * SENSE (the command would loop forever getting a transfer length | |
47 | * mismatch in the CMD phase). | |
48 | * | |
49 | * Version 2.7 | |
50 | * | |
51 | * Fixed scripts problem which caused certain devices (notably CDRWs) | |
52 | * to hang on initial INQUIRY. Updated NCR_700_readl/writel to use | |
53 | * __raw_readl/writel for parisc compatibility (Thomas | |
54 | * Bogendoerfer). Added missing SCp->request_bufflen initialisation | |
55 | * for sense requests (Ryan Bradetich). | |
56 | * | |
57 | * Version 2.6 | |
58 | * | |
59 | * Following test of the 64 bit parisc kernel by Richard Hirst, | |
60 | * several problems have now been corrected. Also adds support for | |
61 | * consistent memory allocation. | |
62 | * | |
63 | * Version 2.5 | |
64 | * | |
65 | * More Compatibility changes for 710 (now actually works). Enhanced | |
66 | * support for odd clock speeds which constrain SDTR negotiations. | |
67 | * correct cacheline separation for scsi messages and status for | |
68 | * incoherent architectures. Use of the pci mapping functions on | |
69 | * buffers to begin support for 64 bit drivers. | |
70 | * | |
71 | * Version 2.4 | |
72 | * | |
73 | * Added support for the 53c710 chip (in 53c700 emulation mode only---no | |
74 | * special 53c710 instructions or registers are used). | |
75 | * | |
76 | * Version 2.3 | |
77 | * | |
78 | * More endianness/cache coherency changes. | |
79 | * | |
80 | * Better bad device handling (handles devices lying about tag | |
81 | * queueing support and devices which fail to provide sense data on | |
82 | * contingent allegiance conditions) | |
83 | * | |
84 | * Many thanks to Richard Hirst <rhirst@linuxcare.com> for patiently | |
85 | * debugging this driver on the parisc architecture and suggesting | |
86 | * many improvements and bug fixes. | |
87 | * | |
88 | * Thanks also go to Linuxcare Inc. for providing several PARISC | |
89 | * machines for me to debug the driver on. | |
90 | * | |
91 | * Version 2.2 | |
92 | * | |
93 | * Made the driver mem or io mapped; added endian invariance; added | |
94 | * dma cache flushing operations for architectures which need it; | |
95 | * added support for more varied clocking speeds. | |
96 | * | |
97 | * Version 2.1 | |
98 | * | |
99 | * Initial modularisation from the D700. See NCR_D700.c for the rest of | |
100 | * the changelog. | |
101 | * */ | |
102 | #define NCR_700_VERSION "2.8" | |
103 | ||
1da177e4 LT |
104 | #include <linux/kernel.h> |
105 | #include <linux/types.h> | |
106 | #include <linux/string.h> | |
5a0e3ad6 | 107 | #include <linux/slab.h> |
1da177e4 LT |
108 | #include <linux/ioport.h> |
109 | #include <linux/delay.h> | |
110 | #include <linux/spinlock.h> | |
111 | #include <linux/completion.h> | |
1da177e4 LT |
112 | #include <linux/init.h> |
113 | #include <linux/proc_fs.h> | |
114 | #include <linux/blkdev.h> | |
115 | #include <linux/module.h> | |
116 | #include <linux/interrupt.h> | |
017560fc | 117 | #include <linux/device.h> |
65fddcfc | 118 | #include <linux/pgtable.h> |
1da177e4 | 119 | #include <asm/dma.h> |
1da177e4 | 120 | #include <asm/io.h> |
1da177e4 LT |
121 | #include <asm/byteorder.h> |
122 | ||
123 | #include <scsi/scsi.h> | |
124 | #include <scsi/scsi_cmnd.h> | |
125 | #include <scsi/scsi_dbg.h> | |
126 | #include <scsi/scsi_eh.h> | |
127 | #include <scsi/scsi_host.h> | |
128 | #include <scsi/scsi_tcq.h> | |
129 | #include <scsi/scsi_transport.h> | |
130 | #include <scsi/scsi_transport_spi.h> | |
131 | ||
132 | #include "53c700.h" | |
133 | ||
134 | /* NOTE: For 64 bit drivers there are points in the code where we use | |
135 | * a non dereferenceable pointer to point to a structure in dma-able | |
136 | * memory (which is 32 bits) so that we can use all of the structure | |
137 | * operations but take the address at the end. This macro allows us | |
138 | * to truncate the 64 bit pointer down to 32 bits without the compiler | |
139 | * complaining */ | |
140 | #define to32bit(x) ((__u32)((unsigned long)(x))) | |
141 | ||
142 | #ifdef NCR_700_DEBUG | |
143 | #define STATIC | |
144 | #else | |
145 | #define STATIC static | |
146 | #endif | |
147 | ||
148 | MODULE_AUTHOR("James Bottomley"); | |
149 | MODULE_DESCRIPTION("53c700 and 53c700-66 Driver"); | |
150 | MODULE_LICENSE("GPL"); | |
151 | ||
152 | /* This is the script */ | |
153 | #include "53c700_d.h" | |
154 | ||
155 | ||
f281233d | 156 | STATIC int NCR_700_queuecommand(struct Scsi_Host *h, struct scsi_cmnd *); |
1da177e4 | 157 | STATIC int NCR_700_abort(struct scsi_cmnd * SCpnt); |
1da177e4 LT |
158 | STATIC int NCR_700_host_reset(struct scsi_cmnd * SCpnt); |
159 | STATIC void NCR_700_chip_setup(struct Scsi_Host *host); | |
160 | STATIC void NCR_700_chip_reset(struct Scsi_Host *host); | |
0f13fc09 | 161 | STATIC int NCR_700_slave_alloc(struct scsi_device *SDpnt); |
1da177e4 LT |
162 | STATIC int NCR_700_slave_configure(struct scsi_device *SDpnt); |
163 | STATIC void NCR_700_slave_destroy(struct scsi_device *SDpnt); | |
db5ed4df | 164 | static int NCR_700_change_queue_depth(struct scsi_device *SDpnt, int depth); |
1da177e4 | 165 | |
90cb6538 | 166 | STATIC const struct attribute_group *NCR_700_dev_groups[]; |
1da177e4 LT |
167 | |
168 | STATIC struct scsi_transport_template *NCR_700_transport_template = NULL; | |
169 | ||
170 | static char *NCR_700_phase[] = { | |
171 | "", | |
172 | "after selection", | |
173 | "before command phase", | |
174 | "after command phase", | |
175 | "after status phase", | |
176 | "after data in phase", | |
177 | "after data out phase", | |
178 | "during data phase", | |
179 | }; | |
180 | ||
181 | static char *NCR_700_condition[] = { | |
182 | "", | |
183 | "NOT MSG_OUT", | |
184 | "UNEXPECTED PHASE", | |
185 | "NOT MSG_IN", | |
186 | "UNEXPECTED MSG", | |
187 | "MSG_IN", | |
188 | "SDTR_MSG RECEIVED", | |
189 | "REJECT_MSG RECEIVED", | |
190 | "DISCONNECT_MSG RECEIVED", | |
191 | "MSG_OUT", | |
192 | "DATA_IN", | |
193 | ||
194 | }; | |
195 | ||
196 | static char *NCR_700_fatal_messages[] = { | |
197 | "unexpected message after reselection", | |
198 | "still MSG_OUT after message injection", | |
199 | "not MSG_IN after selection", | |
200 | "Illegal message length received", | |
201 | }; | |
202 | ||
203 | static char *NCR_700_SBCL_bits[] = { | |
204 | "IO ", | |
205 | "CD ", | |
206 | "MSG ", | |
207 | "ATN ", | |
208 | "SEL ", | |
209 | "BSY ", | |
210 | "ACK ", | |
211 | "REQ ", | |
212 | }; | |
213 | ||
214 | static char *NCR_700_SBCL_to_phase[] = { | |
215 | "DATA_OUT", | |
216 | "DATA_IN", | |
217 | "CMD_OUT", | |
218 | "STATE", | |
219 | "ILLEGAL PHASE", | |
220 | "ILLEGAL PHASE", | |
221 | "MSG OUT", | |
222 | "MSG IN", | |
223 | }; | |
224 | ||
1da177e4 LT |
225 | /* This translates the SDTR message offset and period to a value |
226 | * which can be loaded into the SXFER_REG. | |
227 | * | |
228 | * NOTE: According to SCSI-2, the true transfer period (in ns) is | |
229 | * actually four times this period value */ | |
230 | static inline __u8 | |
231 | NCR_700_offset_period_to_sxfer(struct NCR_700_Host_Parameters *hostdata, | |
232 | __u8 offset, __u8 period) | |
233 | { | |
234 | int XFERP; | |
235 | ||
236 | __u8 min_xferp = (hostdata->chip710 | |
237 | ? NCR_710_MIN_XFERP : NCR_700_MIN_XFERP); | |
238 | __u8 max_offset = (hostdata->chip710 | |
239 | ? NCR_710_MAX_OFFSET : NCR_700_MAX_OFFSET); | |
240 | ||
241 | if(offset == 0) | |
242 | return 0; | |
243 | ||
244 | if(period < hostdata->min_period) { | |
6ea3c0b2 | 245 | printk(KERN_WARNING "53c700: Period %dns is less than this chip's minimum, setting to %d\n", period*4, NCR_700_MIN_PERIOD*4); |
1da177e4 LT |
246 | period = hostdata->min_period; |
247 | } | |
248 | XFERP = (period*4 * hostdata->sync_clock)/1000 - 4; | |
249 | if(offset > max_offset) { | |
250 | printk(KERN_WARNING "53c700: Offset %d exceeds chip maximum, setting to %d\n", | |
251 | offset, max_offset); | |
252 | offset = max_offset; | |
253 | } | |
254 | if(XFERP < min_xferp) { | |
1da177e4 LT |
255 | XFERP = min_xferp; |
256 | } | |
257 | return (offset & 0x0f) | (XFERP & 0x07)<<4; | |
258 | } | |
259 | ||
260 | static inline __u8 | |
261 | NCR_700_get_SXFER(struct scsi_device *SDp) | |
262 | { | |
263 | struct NCR_700_Host_Parameters *hostdata = | |
264 | (struct NCR_700_Host_Parameters *)SDp->host->hostdata[0]; | |
265 | ||
266 | return NCR_700_offset_period_to_sxfer(hostdata, | |
267 | spi_offset(SDp->sdev_target), | |
268 | spi_period(SDp->sdev_target)); | |
269 | } | |
270 | ||
d69d8adc CH |
271 | static inline dma_addr_t virt_to_dma(struct NCR_700_Host_Parameters *h, void *p) |
272 | { | |
273 | return h->pScript + ((uintptr_t)p - (uintptr_t)h->script); | |
274 | } | |
275 | ||
91af2dd2 CH |
276 | static inline void dma_sync_to_dev(struct NCR_700_Host_Parameters *h, |
277 | void *addr, size_t size) | |
278 | { | |
279 | if (h->noncoherent) | |
d69d8adc CH |
280 | dma_sync_single_for_device(h->dev, virt_to_dma(h, addr), |
281 | size, DMA_BIDIRECTIONAL); | |
91af2dd2 CH |
282 | } |
283 | ||
284 | static inline void dma_sync_from_dev(struct NCR_700_Host_Parameters *h, | |
285 | void *addr, size_t size) | |
286 | { | |
287 | if (h->noncoherent) | |
d69d8adc CH |
288 | dma_sync_single_for_device(h->dev, virt_to_dma(h, addr), size, |
289 | DMA_BIDIRECTIONAL); | |
91af2dd2 CH |
290 | } |
291 | ||
1da177e4 LT |
292 | struct Scsi_Host * |
293 | NCR_700_detect(struct scsi_host_template *tpnt, | |
294 | struct NCR_700_Host_Parameters *hostdata, struct device *dev) | |
295 | { | |
296 | dma_addr_t pScript, pSlots; | |
297 | __u8 *memory; | |
298 | __u32 *script; | |
299 | struct Scsi_Host *host; | |
300 | static int banner = 0; | |
301 | int j; | |
302 | ||
90cb6538 BVA |
303 | if (tpnt->sdev_groups == NULL) |
304 | tpnt->sdev_groups = NCR_700_dev_groups; | |
1da177e4 | 305 | |
91af2dd2 CH |
306 | memory = dma_alloc_coherent(dev, TOTAL_MEM_SIZE, &pScript, GFP_KERNEL); |
307 | if (!memory) { | |
308 | hostdata->noncoherent = 1; | |
d69d8adc CH |
309 | memory = dma_alloc_noncoherent(dev, TOTAL_MEM_SIZE, &pScript, |
310 | DMA_BIDIRECTIONAL, GFP_KERNEL); | |
91af2dd2 CH |
311 | } |
312 | if (!memory) { | |
804ff603 | 313 | printk(KERN_ERR "53c700: Failed to allocate memory for driver, detaching\n"); |
1da177e4 LT |
314 | return NULL; |
315 | } | |
316 | ||
317 | script = (__u32 *)memory; | |
318 | hostdata->msgin = memory + MSGIN_OFFSET; | |
319 | hostdata->msgout = memory + MSGOUT_OFFSET; | |
320 | hostdata->status = memory + STATUS_OFFSET; | |
1da177e4 LT |
321 | hostdata->slots = (struct NCR_700_command_slot *)(memory + SLOTS_OFFSET); |
322 | hostdata->dev = dev; | |
6391a113 | 323 | |
1da177e4 LT |
324 | pSlots = pScript + SLOTS_OFFSET; |
325 | ||
326 | /* Fill in the missing routines from the host template */ | |
327 | tpnt->queuecommand = NCR_700_queuecommand; | |
328 | tpnt->eh_abort_handler = NCR_700_abort; | |
1da177e4 LT |
329 | tpnt->eh_host_reset_handler = NCR_700_host_reset; |
330 | tpnt->can_queue = NCR_700_COMMAND_SLOTS_PER_HOST; | |
331 | tpnt->sg_tablesize = NCR_700_SG_SEGMENTS; | |
332 | tpnt->cmd_per_lun = NCR_700_CMD_PER_LUN; | |
1da177e4 LT |
333 | tpnt->slave_configure = NCR_700_slave_configure; |
334 | tpnt->slave_destroy = NCR_700_slave_destroy; | |
0f13fc09 | 335 | tpnt->slave_alloc = NCR_700_slave_alloc; |
1da177e4 | 336 | tpnt->change_queue_depth = NCR_700_change_queue_depth; |
6391a113 | 337 | |
1da177e4 LT |
338 | if(tpnt->name == NULL) |
339 | tpnt->name = "53c700"; | |
340 | if(tpnt->proc_name == NULL) | |
341 | tpnt->proc_name = "53c700"; | |
1da177e4 LT |
342 | |
343 | host = scsi_host_alloc(tpnt, 4); | |
344 | if (!host) | |
345 | return NULL; | |
346 | memset(hostdata->slots, 0, sizeof(struct NCR_700_command_slot) | |
347 | * NCR_700_COMMAND_SLOTS_PER_HOST); | |
6391a113 | 348 | for (j = 0; j < NCR_700_COMMAND_SLOTS_PER_HOST; j++) { |
1da177e4 LT |
349 | dma_addr_t offset = (dma_addr_t)((unsigned long)&hostdata->slots[j].SG[0] |
350 | - (unsigned long)&hostdata->slots[0].SG[0]); | |
351 | hostdata->slots[j].pSG = (struct NCR_700_SG_List *)((unsigned long)(pSlots + offset)); | |
352 | if(j == 0) | |
353 | hostdata->free_list = &hostdata->slots[j]; | |
354 | else | |
355 | hostdata->slots[j-1].ITL_forw = &hostdata->slots[j]; | |
356 | hostdata->slots[j].state = NCR_700_SLOT_FREE; | |
357 | } | |
358 | ||
6391a113 | 359 | for (j = 0; j < ARRAY_SIZE(SCRIPT); j++) |
1da177e4 | 360 | script[j] = bS_to_host(SCRIPT[j]); |
1da177e4 LT |
361 | |
362 | /* adjust all labels to be bus physical */ | |
6391a113 | 363 | for (j = 0; j < PATCHES; j++) |
1da177e4 | 364 | script[LABELPATCHES[j]] = bS_to_host(pScript + SCRIPT[LABELPATCHES[j]]); |
1da177e4 | 365 | /* now patch up fixed addresses. */ |
91af2dd2 | 366 | script_patch_32(hostdata, script, MessageLocation, |
1da177e4 | 367 | pScript + MSGOUT_OFFSET); |
91af2dd2 | 368 | script_patch_32(hostdata, script, StatusAddress, |
1da177e4 | 369 | pScript + STATUS_OFFSET); |
91af2dd2 | 370 | script_patch_32(hostdata, script, ReceiveMsgAddress, |
1da177e4 LT |
371 | pScript + MSGIN_OFFSET); |
372 | ||
373 | hostdata->script = script; | |
374 | hostdata->pScript = pScript; | |
375 | dma_sync_single_for_device(hostdata->dev, pScript, sizeof(SCRIPT), DMA_TO_DEVICE); | |
376 | hostdata->state = NCR_700_HOST_FREE; | |
377 | hostdata->cmd = NULL; | |
2b89dad0 | 378 | host->max_id = 8; |
1da177e4 LT |
379 | host->max_lun = NCR_700_MAX_LUNS; |
380 | BUG_ON(NCR_700_transport_template == NULL); | |
381 | host->transportt = NCR_700_transport_template; | |
56fece20 | 382 | host->unique_id = (unsigned long)hostdata->base; |
1da177e4 LT |
383 | hostdata->eh_complete = NULL; |
384 | host->hostdata[0] = (unsigned long)hostdata; | |
385 | /* kick the chip */ | |
386 | NCR_700_writeb(0xff, host, CTEST9_REG); | |
6391a113 | 387 | if (hostdata->chip710) |
1da177e4 LT |
388 | hostdata->rev = (NCR_700_readb(host, CTEST8_REG)>>4) & 0x0f; |
389 | else | |
390 | hostdata->rev = (NCR_700_readb(host, CTEST7_REG)>>4) & 0x0f; | |
391 | hostdata->fast = (NCR_700_readb(host, CTEST9_REG) == 0); | |
6391a113 | 392 | if (banner == 0) { |
1da177e4 LT |
393 | printk(KERN_NOTICE "53c700: Version " NCR_700_VERSION " By James.Bottomley@HansenPartnership.com\n"); |
394 | banner = 1; | |
395 | } | |
396 | printk(KERN_NOTICE "scsi%d: %s rev %d %s\n", host->host_no, | |
6391a113 | 397 | hostdata->chip710 ? "53c710" : |
1da177e4 LT |
398 | (hostdata->fast ? "53c700-66" : "53c700"), |
399 | hostdata->rev, hostdata->differential ? | |
400 | "(Differential)" : ""); | |
401 | /* reset the chip */ | |
402 | NCR_700_chip_reset(host); | |
403 | ||
404 | if (scsi_add_host(host, dev)) { | |
405 | dev_printk(KERN_ERR, dev, "53c700: scsi_add_host failed\n"); | |
406 | scsi_host_put(host); | |
407 | return NULL; | |
408 | } | |
409 | ||
410 | spi_signalling(host) = hostdata->differential ? SPI_SIGNAL_HVD : | |
411 | SPI_SIGNAL_SE; | |
412 | ||
413 | return host; | |
414 | } | |
415 | ||
416 | int | |
417 | NCR_700_release(struct Scsi_Host *host) | |
418 | { | |
419 | struct NCR_700_Host_Parameters *hostdata = | |
420 | (struct NCR_700_Host_Parameters *)host->hostdata[0]; | |
421 | ||
91af2dd2 | 422 | if (hostdata->noncoherent) |
d69d8adc CH |
423 | dma_free_noncoherent(hostdata->dev, TOTAL_MEM_SIZE, |
424 | hostdata->script, hostdata->pScript, | |
425 | DMA_BIDIRECTIONAL); | |
91af2dd2 CH |
426 | else |
427 | dma_free_coherent(hostdata->dev, TOTAL_MEM_SIZE, | |
428 | hostdata->script, hostdata->pScript); | |
1da177e4 LT |
429 | return 1; |
430 | } | |
431 | ||
432 | static inline __u8 | |
433 | NCR_700_identify(int can_disconnect, __u8 lun) | |
434 | { | |
435 | return IDENTIFY_BASE | | |
436 | ((can_disconnect) ? 0x40 : 0) | | |
437 | (lun & NCR_700_LUN_MASK); | |
438 | } | |
439 | ||
440 | /* | |
441 | * Function : static int data_residual (Scsi_Host *host) | |
442 | * | |
443 | * Purpose : return residual data count of what's in the chip. If you | |
444 | * really want to know what this function is doing, it's almost a | |
445 | * direct transcription of the algorithm described in the 53c710 | |
446 | * guide, except that the DBC and DFIFO registers are only 6 bits | |
447 | * wide on a 53c700. | |
448 | * | |
449 | * Inputs : host - SCSI host */ | |
450 | static inline int | |
451 | NCR_700_data_residual (struct Scsi_Host *host) { | |
452 | struct NCR_700_Host_Parameters *hostdata = | |
453 | (struct NCR_700_Host_Parameters *)host->hostdata[0]; | |
454 | int count, synchronous = 0; | |
455 | unsigned int ddir; | |
456 | ||
457 | if(hostdata->chip710) { | |
458 | count = ((NCR_700_readb(host, DFIFO_REG) & 0x7f) - | |
459 | (NCR_700_readl(host, DBC_REG) & 0x7f)) & 0x7f; | |
460 | } else { | |
461 | count = ((NCR_700_readb(host, DFIFO_REG) & 0x3f) - | |
462 | (NCR_700_readl(host, DBC_REG) & 0x3f)) & 0x3f; | |
463 | } | |
464 | ||
465 | if(hostdata->fast) | |
466 | synchronous = NCR_700_readb(host, SXFER_REG) & 0x0f; | |
467 | ||
468 | /* get the data direction */ | |
469 | ddir = NCR_700_readb(host, CTEST0_REG) & 0x01; | |
470 | ||
471 | if (ddir) { | |
472 | /* Receive */ | |
473 | if (synchronous) | |
474 | count += (NCR_700_readb(host, SSTAT2_REG) & 0xf0) >> 4; | |
475 | else | |
476 | if (NCR_700_readb(host, SSTAT1_REG) & SIDL_REG_FULL) | |
477 | ++count; | |
478 | } else { | |
479 | /* Send */ | |
480 | __u8 sstat = NCR_700_readb(host, SSTAT1_REG); | |
481 | if (sstat & SODL_REG_FULL) | |
482 | ++count; | |
483 | if (synchronous && (sstat & SODR_REG_FULL)) | |
484 | ++count; | |
485 | } | |
486 | #ifdef NCR_700_DEBUG | |
487 | if(count) | |
488 | printk("RESIDUAL IS %d (ddir %d)\n", count, ddir); | |
489 | #endif | |
490 | return count; | |
491 | } | |
492 | ||
493 | /* print out the SCSI wires and corresponding phase from the SBCL register | |
494 | * in the chip */ | |
495 | static inline char * | |
496 | sbcl_to_string(__u8 sbcl) | |
497 | { | |
498 | int i; | |
499 | static char ret[256]; | |
500 | ||
501 | ret[0]='\0'; | |
502 | for(i=0; i<8; i++) { | |
503 | if((1<<i) & sbcl) | |
504 | strcat(ret, NCR_700_SBCL_bits[i]); | |
505 | } | |
506 | strcat(ret, NCR_700_SBCL_to_phase[sbcl & 0x07]); | |
507 | return ret; | |
508 | } | |
509 | ||
510 | static inline __u8 | |
511 | bitmap_to_number(__u8 bitmap) | |
512 | { | |
513 | __u8 i; | |
514 | ||
515 | for(i=0; i<8 && !(bitmap &(1<<i)); i++) | |
516 | ; | |
517 | return i; | |
518 | } | |
519 | ||
520 | /* Pull a slot off the free list */ | |
521 | STATIC struct NCR_700_command_slot * | |
522 | find_empty_slot(struct NCR_700_Host_Parameters *hostdata) | |
523 | { | |
524 | struct NCR_700_command_slot *slot = hostdata->free_list; | |
525 | ||
526 | if(slot == NULL) { | |
527 | /* sanity check */ | |
528 | if(hostdata->command_slot_count != NCR_700_COMMAND_SLOTS_PER_HOST) | |
529 | printk(KERN_ERR "SLOTS FULL, but count is %d, should be %d\n", hostdata->command_slot_count, NCR_700_COMMAND_SLOTS_PER_HOST); | |
530 | return NULL; | |
531 | } | |
532 | ||
533 | if(slot->state != NCR_700_SLOT_FREE) | |
534 | /* should panic! */ | |
535 | printk(KERN_ERR "BUSY SLOT ON FREE LIST!!!\n"); | |
536 | ||
537 | ||
538 | hostdata->free_list = slot->ITL_forw; | |
539 | slot->ITL_forw = NULL; | |
540 | ||
541 | ||
542 | /* NOTE: set the state to busy here, not queued, since this | |
543 | * indicates the slot is in use and cannot be run by the IRQ | |
544 | * finish routine. If we cannot queue the command when it | |
545 | * is properly build, we then change to NCR_700_SLOT_QUEUED */ | |
546 | slot->state = NCR_700_SLOT_BUSY; | |
67d59dfd | 547 | slot->flags = 0; |
1da177e4 LT |
548 | hostdata->command_slot_count++; |
549 | ||
550 | return slot; | |
551 | } | |
552 | ||
553 | STATIC void | |
554 | free_slot(struct NCR_700_command_slot *slot, | |
555 | struct NCR_700_Host_Parameters *hostdata) | |
556 | { | |
557 | if((slot->state & NCR_700_SLOT_MASK) != NCR_700_SLOT_MAGIC) { | |
558 | printk(KERN_ERR "53c700: SLOT %p is not MAGIC!!!\n", slot); | |
559 | } | |
560 | if(slot->state == NCR_700_SLOT_FREE) { | |
561 | printk(KERN_ERR "53c700: SLOT %p is FREE!!!\n", slot); | |
562 | } | |
563 | ||
564 | slot->resume_offset = 0; | |
565 | slot->cmnd = NULL; | |
566 | slot->state = NCR_700_SLOT_FREE; | |
567 | slot->ITL_forw = hostdata->free_list; | |
568 | hostdata->free_list = slot; | |
569 | hostdata->command_slot_count--; | |
570 | } | |
571 | ||
572 | ||
573 | /* This routine really does very little. The command is indexed on | |
574 | the ITL and (if tagged) the ITLQ lists in _queuecommand */ | |
575 | STATIC void | |
576 | save_for_reselection(struct NCR_700_Host_Parameters *hostdata, | |
577 | struct scsi_cmnd *SCp, __u32 dsp) | |
578 | { | |
579 | /* Its just possible that this gets executed twice */ | |
580 | if(SCp != NULL) { | |
581 | struct NCR_700_command_slot *slot = | |
582 | (struct NCR_700_command_slot *)SCp->host_scribble; | |
583 | ||
584 | slot->resume_offset = dsp; | |
585 | } | |
586 | hostdata->state = NCR_700_HOST_FREE; | |
587 | hostdata->cmd = NULL; | |
588 | } | |
589 | ||
590 | STATIC inline void | |
591 | NCR_700_unmap(struct NCR_700_Host_Parameters *hostdata, struct scsi_cmnd *SCp, | |
592 | struct NCR_700_command_slot *slot) | |
593 | { | |
594 | if(SCp->sc_data_direction != DMA_NONE && | |
3258a4d5 FT |
595 | SCp->sc_data_direction != DMA_BIDIRECTIONAL) |
596 | scsi_dma_unmap(SCp); | |
1da177e4 LT |
597 | } |
598 | ||
599 | STATIC inline void | |
600 | NCR_700_scsi_done(struct NCR_700_Host_Parameters *hostdata, | |
601 | struct scsi_cmnd *SCp, int result) | |
602 | { | |
603 | hostdata->state = NCR_700_HOST_FREE; | |
604 | hostdata->cmd = NULL; | |
605 | ||
606 | if(SCp != NULL) { | |
7d170907 | 607 | struct NCR_700_command_slot *slot = |
1da177e4 | 608 | (struct NCR_700_command_slot *)SCp->host_scribble; |
7d170907 | 609 | |
0f13fc09 | 610 | dma_unmap_single(hostdata->dev, slot->pCmd, |
64a87b24 | 611 | MAX_COMMAND_SIZE, DMA_TO_DEVICE); |
67d59dfd | 612 | if (slot->flags == NCR_700_FLAG_AUTOSENSE) { |
0f13fc09 | 613 | char *cmnd = NCR_700_get_sense_cmnd(SCp->device); |
1da177e4 | 614 | |
b80ca4f7 FT |
615 | dma_unmap_single(hostdata->dev, slot->dma_handle, |
616 | SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); | |
1da177e4 LT |
617 | /* restore the old result if the request sense was |
618 | * successful */ | |
c603d04e | 619 | if (result == 0) |
0f13fc09 | 620 | result = cmnd[7]; |
c603d04e JB |
621 | /* restore the original length */ |
622 | SCp->cmd_len = cmnd[8]; | |
67d59dfd | 623 | } else |
0f13fc09 | 624 | NCR_700_unmap(hostdata, SCp, slot); |
67d59dfd | 625 | |
1da177e4 LT |
626 | free_slot(slot, hostdata); |
627 | #ifdef NCR_700_DEBUG | |
628 | if(NCR_700_get_depth(SCp->device) == 0 || | |
629 | NCR_700_get_depth(SCp->device) > SCp->device->queue_depth) | |
630 | printk(KERN_ERR "Invalid depth in NCR_700_scsi_done(): %d\n", | |
631 | NCR_700_get_depth(SCp->device)); | |
632 | #endif /* NCR_700_DEBUG */ | |
633 | NCR_700_set_depth(SCp->device, NCR_700_get_depth(SCp->device) - 1); | |
634 | ||
635 | SCp->host_scribble = NULL; | |
636 | SCp->result = result; | |
656f26ad | 637 | scsi_done(SCp); |
1da177e4 LT |
638 | } else { |
639 | printk(KERN_ERR "53c700: SCSI DONE HAS NULL SCp\n"); | |
640 | } | |
641 | } | |
642 | ||
643 | ||
644 | STATIC void | |
645 | NCR_700_internal_bus_reset(struct Scsi_Host *host) | |
646 | { | |
647 | /* Bus reset */ | |
648 | NCR_700_writeb(ASSERT_RST, host, SCNTL1_REG); | |
649 | udelay(50); | |
650 | NCR_700_writeb(0, host, SCNTL1_REG); | |
651 | ||
652 | } | |
653 | ||
654 | STATIC void | |
655 | NCR_700_chip_setup(struct Scsi_Host *host) | |
656 | { | |
657 | struct NCR_700_Host_Parameters *hostdata = | |
658 | (struct NCR_700_Host_Parameters *)host->hostdata[0]; | |
1da177e4 LT |
659 | __u8 min_period; |
660 | __u8 min_xferp = (hostdata->chip710 ? NCR_710_MIN_XFERP : NCR_700_MIN_XFERP); | |
661 | ||
662 | if(hostdata->chip710) { | |
f67a9c15 TB |
663 | __u8 burst_disable = 0; |
664 | __u8 burst_length = 0; | |
665 | ||
666 | switch (hostdata->burst_length) { | |
667 | case 1: | |
668 | burst_length = BURST_LENGTH_1; | |
669 | break; | |
670 | case 2: | |
671 | burst_length = BURST_LENGTH_2; | |
672 | break; | |
673 | case 4: | |
674 | burst_length = BURST_LENGTH_4; | |
675 | break; | |
676 | case 8: | |
677 | burst_length = BURST_LENGTH_8; | |
678 | break; | |
679 | default: | |
680 | burst_disable = BURST_DISABLE; | |
681 | break; | |
682 | } | |
63273134 | 683 | hostdata->dcntl_extra |= COMPAT_700_MODE; |
1da177e4 | 684 | |
63273134 | 685 | NCR_700_writeb(hostdata->dcntl_extra, host, DCNTL_REG); |
f67a9c15 | 686 | NCR_700_writeb(burst_length | hostdata->dmode_extra, |
1da177e4 | 687 | host, DMODE_710_REG); |
63273134 KJ |
688 | NCR_700_writeb(burst_disable | hostdata->ctest7_extra | |
689 | (hostdata->differential ? DIFF : 0), | |
690 | host, CTEST7_REG); | |
1da177e4 LT |
691 | NCR_700_writeb(BTB_TIMER_DISABLE, host, CTEST0_REG); |
692 | NCR_700_writeb(FULL_ARBITRATION | ENABLE_PARITY | PARITY | |
693 | | AUTO_ATN, host, SCNTL0_REG); | |
694 | } else { | |
695 | NCR_700_writeb(BURST_LENGTH_8 | hostdata->dmode_extra, | |
696 | host, DMODE_700_REG); | |
697 | NCR_700_writeb(hostdata->differential ? | |
698 | DIFF : 0, host, CTEST7_REG); | |
699 | if(hostdata->fast) { | |
700 | /* this is for 700-66, does nothing on 700 */ | |
701 | NCR_700_writeb(LAST_DIS_ENBL | ENABLE_ACTIVE_NEGATION | |
702 | | GENERATE_RECEIVE_PARITY, host, | |
703 | CTEST8_REG); | |
704 | } else { | |
705 | NCR_700_writeb(FULL_ARBITRATION | ENABLE_PARITY | |
706 | | PARITY | AUTO_ATN, host, SCNTL0_REG); | |
707 | } | |
708 | } | |
709 | ||
710 | NCR_700_writeb(1 << host->this_id, host, SCID_REG); | |
711 | NCR_700_writeb(0, host, SBCL_REG); | |
712 | NCR_700_writeb(ASYNC_OPERATION, host, SXFER_REG); | |
713 | ||
714 | NCR_700_writeb(PHASE_MM_INT | SEL_TIMEOUT_INT | GROSS_ERR_INT | UX_DISC_INT | |
715 | | RST_INT | PAR_ERR_INT | SELECT_INT, host, SIEN_REG); | |
716 | ||
717 | NCR_700_writeb(ABORT_INT | INT_INST_INT | ILGL_INST_INT, host, DIEN_REG); | |
718 | NCR_700_writeb(ENABLE_SELECT, host, SCNTL1_REG); | |
719 | if(hostdata->clock > 75) { | |
720 | printk(KERN_ERR "53c700: Clock speed %dMHz is too high: 75Mhz is the maximum this chip can be driven at\n", hostdata->clock); | |
721 | /* do the best we can, but the async clock will be out | |
722 | * of spec: sync divider 2, async divider 3 */ | |
723 | DEBUG(("53c700: sync 2 async 3\n")); | |
724 | NCR_700_writeb(SYNC_DIV_2_0, host, SBCL_REG); | |
63273134 | 725 | NCR_700_writeb(ASYNC_DIV_3_0 | hostdata->dcntl_extra, host, DCNTL_REG); |
1da177e4 LT |
726 | hostdata->sync_clock = hostdata->clock/2; |
727 | } else if(hostdata->clock > 50 && hostdata->clock <= 75) { | |
728 | /* sync divider 1.5, async divider 3 */ | |
729 | DEBUG(("53c700: sync 1.5 async 3\n")); | |
730 | NCR_700_writeb(SYNC_DIV_1_5, host, SBCL_REG); | |
63273134 | 731 | NCR_700_writeb(ASYNC_DIV_3_0 | hostdata->dcntl_extra, host, DCNTL_REG); |
1da177e4 LT |
732 | hostdata->sync_clock = hostdata->clock*2; |
733 | hostdata->sync_clock /= 3; | |
734 | ||
735 | } else if(hostdata->clock > 37 && hostdata->clock <= 50) { | |
736 | /* sync divider 1, async divider 2 */ | |
737 | DEBUG(("53c700: sync 1 async 2\n")); | |
738 | NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG); | |
63273134 | 739 | NCR_700_writeb(ASYNC_DIV_2_0 | hostdata->dcntl_extra, host, DCNTL_REG); |
1da177e4 LT |
740 | hostdata->sync_clock = hostdata->clock; |
741 | } else if(hostdata->clock > 25 && hostdata->clock <=37) { | |
742 | /* sync divider 1, async divider 1.5 */ | |
743 | DEBUG(("53c700: sync 1 async 1.5\n")); | |
744 | NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG); | |
63273134 | 745 | NCR_700_writeb(ASYNC_DIV_1_5 | hostdata->dcntl_extra, host, DCNTL_REG); |
1da177e4 LT |
746 | hostdata->sync_clock = hostdata->clock; |
747 | } else { | |
748 | DEBUG(("53c700: sync 1 async 1\n")); | |
749 | NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG); | |
63273134 | 750 | NCR_700_writeb(ASYNC_DIV_1_0 | hostdata->dcntl_extra, host, DCNTL_REG); |
1da177e4 LT |
751 | /* sync divider 1, async divider 1 */ |
752 | hostdata->sync_clock = hostdata->clock; | |
753 | } | |
754 | /* Calculate the actual minimum period that can be supported | |
755 | * by our synchronous clock speed. See the 710 manual for | |
756 | * exact details of this calculation which is based on a | |
757 | * setting of the SXFER register */ | |
758 | min_period = 1000*(4+min_xferp)/(4*hostdata->sync_clock); | |
759 | hostdata->min_period = NCR_700_MIN_PERIOD; | |
760 | if(min_period > NCR_700_MIN_PERIOD) | |
761 | hostdata->min_period = min_period; | |
762 | } | |
763 | ||
764 | STATIC void | |
765 | NCR_700_chip_reset(struct Scsi_Host *host) | |
766 | { | |
767 | struct NCR_700_Host_Parameters *hostdata = | |
768 | (struct NCR_700_Host_Parameters *)host->hostdata[0]; | |
769 | if(hostdata->chip710) { | |
770 | NCR_700_writeb(SOFTWARE_RESET_710, host, ISTAT_REG); | |
771 | udelay(100); | |
772 | ||
773 | NCR_700_writeb(0, host, ISTAT_REG); | |
774 | } else { | |
775 | NCR_700_writeb(SOFTWARE_RESET, host, DCNTL_REG); | |
776 | udelay(100); | |
777 | ||
778 | NCR_700_writeb(0, host, DCNTL_REG); | |
779 | } | |
780 | ||
781 | mdelay(1000); | |
782 | ||
783 | NCR_700_chip_setup(host); | |
784 | } | |
785 | ||
786 | /* The heart of the message processing engine is that the instruction | |
787 | * immediately after the INT is the normal case (and so must be CLEAR | |
788 | * ACK). If we want to do something else, we call that routine in | |
789 | * scripts and set temp to be the normal case + 8 (skipping the CLEAR | |
790 | * ACK) so that the routine returns correctly to resume its activity | |
791 | * */ | |
792 | STATIC __u32 | |
793 | process_extended_message(struct Scsi_Host *host, | |
794 | struct NCR_700_Host_Parameters *hostdata, | |
795 | struct scsi_cmnd *SCp, __u32 dsp, __u32 dsps) | |
796 | { | |
797 | __u32 resume_offset = dsp, temp = dsp + 8; | |
798 | __u8 pun = 0xff, lun = 0xff; | |
799 | ||
800 | if(SCp != NULL) { | |
801 | pun = SCp->device->id; | |
802 | lun = SCp->device->lun; | |
803 | } | |
804 | ||
805 | switch(hostdata->msgin[2]) { | |
806 | case A_SDTR_MSG: | |
807 | if(SCp != NULL && NCR_700_is_flag_set(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION)) { | |
808 | struct scsi_target *starget = SCp->device->sdev_target; | |
809 | __u8 period = hostdata->msgin[3]; | |
810 | __u8 offset = hostdata->msgin[4]; | |
811 | ||
812 | if(offset == 0 || period == 0) { | |
813 | offset = 0; | |
814 | period = 0; | |
815 | } | |
816 | ||
817 | spi_offset(starget) = offset; | |
818 | spi_period(starget) = period; | |
819 | ||
820 | if(NCR_700_is_flag_set(SCp->device, NCR_700_DEV_PRINT_SYNC_NEGOTIATION)) { | |
821 | spi_display_xfer_agreement(starget); | |
822 | NCR_700_clear_flag(SCp->device, NCR_700_DEV_PRINT_SYNC_NEGOTIATION); | |
823 | } | |
824 | ||
825 | NCR_700_set_flag(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC); | |
826 | NCR_700_clear_flag(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); | |
827 | ||
828 | NCR_700_writeb(NCR_700_get_SXFER(SCp->device), | |
829 | host, SXFER_REG); | |
830 | ||
831 | } else { | |
832 | /* SDTR message out of the blue, reject it */ | |
017560fc JG |
833 | shost_printk(KERN_WARNING, host, |
834 | "Unexpected SDTR msg\n"); | |
1da177e4 | 835 | hostdata->msgout[0] = A_REJECT_MSG; |
91af2dd2 CH |
836 | dma_sync_to_dev(hostdata, hostdata->msgout, 1); |
837 | script_patch_16(hostdata, hostdata->script, | |
d3fa72e4 | 838 | MessageCount, 1); |
1da177e4 LT |
839 | /* SendMsgOut returns, so set up the return |
840 | * address */ | |
841 | resume_offset = hostdata->pScript + Ent_SendMessageWithATN; | |
842 | } | |
843 | break; | |
844 | ||
845 | case A_WDTR_MSG: | |
846 | printk(KERN_INFO "scsi%d: (%d:%d), Unsolicited WDTR after CMD, Rejecting\n", | |
847 | host->host_no, pun, lun); | |
848 | hostdata->msgout[0] = A_REJECT_MSG; | |
91af2dd2 CH |
849 | dma_sync_to_dev(hostdata, hostdata->msgout, 1); |
850 | script_patch_16(hostdata, hostdata->script, MessageCount, 1); | |
1da177e4 LT |
851 | resume_offset = hostdata->pScript + Ent_SendMessageWithATN; |
852 | ||
853 | break; | |
854 | ||
855 | default: | |
856 | printk(KERN_INFO "scsi%d (%d:%d): Unexpected message %s: ", | |
857 | host->host_no, pun, lun, | |
858 | NCR_700_phase[(dsps & 0xf00) >> 8]); | |
1abfd370 | 859 | spi_print_msg(hostdata->msgin); |
1da177e4 LT |
860 | printk("\n"); |
861 | /* just reject it */ | |
862 | hostdata->msgout[0] = A_REJECT_MSG; | |
91af2dd2 CH |
863 | dma_sync_to_dev(hostdata, hostdata->msgout, 1); |
864 | script_patch_16(hostdata, hostdata->script, MessageCount, 1); | |
1da177e4 LT |
865 | /* SendMsgOut returns, so set up the return |
866 | * address */ | |
867 | resume_offset = hostdata->pScript + Ent_SendMessageWithATN; | |
868 | } | |
869 | NCR_700_writel(temp, host, TEMP_REG); | |
870 | return resume_offset; | |
871 | } | |
872 | ||
873 | STATIC __u32 | |
874 | process_message(struct Scsi_Host *host, struct NCR_700_Host_Parameters *hostdata, | |
875 | struct scsi_cmnd *SCp, __u32 dsp, __u32 dsps) | |
876 | { | |
877 | /* work out where to return to */ | |
878 | __u32 temp = dsp + 8, resume_offset = dsp; | |
879 | __u8 pun = 0xff, lun = 0xff; | |
880 | ||
881 | if(SCp != NULL) { | |
882 | pun = SCp->device->id; | |
883 | lun = SCp->device->lun; | |
884 | } | |
885 | ||
886 | #ifdef NCR_700_DEBUG | |
887 | printk("scsi%d (%d:%d): message %s: ", host->host_no, pun, lun, | |
888 | NCR_700_phase[(dsps & 0xf00) >> 8]); | |
1abfd370 | 889 | spi_print_msg(hostdata->msgin); |
1da177e4 LT |
890 | printk("\n"); |
891 | #endif | |
892 | ||
893 | switch(hostdata->msgin[0]) { | |
894 | ||
895 | case A_EXTENDED_MSG: | |
896 | resume_offset = process_extended_message(host, hostdata, SCp, | |
897 | dsp, dsps); | |
898 | break; | |
899 | ||
900 | case A_REJECT_MSG: | |
901 | if(SCp != NULL && NCR_700_is_flag_set(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION)) { | |
902 | /* Rejected our sync negotiation attempt */ | |
903 | spi_period(SCp->device->sdev_target) = | |
904 | spi_offset(SCp->device->sdev_target) = 0; | |
905 | NCR_700_set_flag(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC); | |
906 | NCR_700_clear_flag(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); | |
907 | } else if(SCp != NULL && NCR_700_get_tag_neg_state(SCp->device) == NCR_700_DURING_TAG_NEGOTIATION) { | |
908 | /* rejected our first simple tag message */ | |
017560fc JG |
909 | scmd_printk(KERN_WARNING, SCp, |
910 | "Rejected first tag queue attempt, turning off tag queueing\n"); | |
1da177e4 LT |
911 | /* we're done negotiating */ |
912 | NCR_700_set_tag_neg_state(SCp->device, NCR_700_FINISHED_TAG_NEGOTIATION); | |
017560fc | 913 | hostdata->tag_negotiated &= ~(1<<scmd_id(SCp)); |
c8b09f6f | 914 | |
1da177e4 | 915 | SCp->device->tagged_supported = 0; |
4e484896 | 916 | SCp->device->simple_tags = 0; |
db5ed4df | 917 | scsi_change_queue_depth(SCp->device, host->cmd_per_lun); |
1da177e4 | 918 | } else { |
017560fc JG |
919 | shost_printk(KERN_WARNING, host, |
920 | "(%d:%d) Unexpected REJECT Message %s\n", | |
921 | pun, lun, | |
1da177e4 LT |
922 | NCR_700_phase[(dsps & 0xf00) >> 8]); |
923 | /* however, just ignore it */ | |
924 | } | |
925 | break; | |
926 | ||
927 | case A_PARITY_ERROR_MSG: | |
928 | printk(KERN_ERR "scsi%d (%d:%d) Parity Error!\n", host->host_no, | |
929 | pun, lun); | |
930 | NCR_700_internal_bus_reset(host); | |
931 | break; | |
932 | case A_SIMPLE_TAG_MSG: | |
933 | printk(KERN_INFO "scsi%d (%d:%d) SIMPLE TAG %d %s\n", host->host_no, | |
934 | pun, lun, hostdata->msgin[1], | |
935 | NCR_700_phase[(dsps & 0xf00) >> 8]); | |
936 | /* just ignore it */ | |
937 | break; | |
938 | default: | |
939 | printk(KERN_INFO "scsi%d (%d:%d): Unexpected message %s: ", | |
940 | host->host_no, pun, lun, | |
941 | NCR_700_phase[(dsps & 0xf00) >> 8]); | |
942 | ||
1abfd370 | 943 | spi_print_msg(hostdata->msgin); |
1da177e4 LT |
944 | printk("\n"); |
945 | /* just reject it */ | |
946 | hostdata->msgout[0] = A_REJECT_MSG; | |
91af2dd2 CH |
947 | dma_sync_to_dev(hostdata, hostdata->msgout, 1); |
948 | script_patch_16(hostdata, hostdata->script, MessageCount, 1); | |
1da177e4 LT |
949 | /* SendMsgOut returns, so set up the return |
950 | * address */ | |
951 | resume_offset = hostdata->pScript + Ent_SendMessageWithATN; | |
952 | ||
953 | break; | |
954 | } | |
955 | NCR_700_writel(temp, host, TEMP_REG); | |
956 | /* set us up to receive another message */ | |
91af2dd2 | 957 | dma_sync_from_dev(hostdata, hostdata->msgin, MSG_ARRAY_SIZE); |
1da177e4 LT |
958 | return resume_offset; |
959 | } | |
960 | ||
961 | STATIC __u32 | |
962 | process_script_interrupt(__u32 dsps, __u32 dsp, struct scsi_cmnd *SCp, | |
963 | struct Scsi_Host *host, | |
964 | struct NCR_700_Host_Parameters *hostdata) | |
965 | { | |
966 | __u32 resume_offset = 0; | |
967 | __u8 pun = 0xff, lun=0xff; | |
968 | ||
969 | if(SCp != NULL) { | |
970 | pun = SCp->device->id; | |
971 | lun = SCp->device->lun; | |
972 | } | |
973 | ||
974 | if(dsps == A_GOOD_STATUS_AFTER_STATUS) { | |
975 | DEBUG((" COMMAND COMPLETE, status=%02x\n", | |
976 | hostdata->status[0])); | |
977 | /* OK, if TCQ still under negotiation, we now know it works */ | |
978 | if (NCR_700_get_tag_neg_state(SCp->device) == NCR_700_DURING_TAG_NEGOTIATION) | |
979 | NCR_700_set_tag_neg_state(SCp->device, | |
980 | NCR_700_FINISHED_TAG_NEGOTIATION); | |
3d45cefc | 981 | |
ac5669bf | 982 | /* check for contingent allegiance conditions */ |
3d45cefc HR |
983 | if (hostdata->status[0] == SAM_STAT_CHECK_CONDITION || |
984 | hostdata->status[0] == SAM_STAT_COMMAND_TERMINATED) { | |
1da177e4 LT |
985 | struct NCR_700_command_slot *slot = |
986 | (struct NCR_700_command_slot *)SCp->host_scribble; | |
0f13fc09 | 987 | if(slot->flags == NCR_700_FLAG_AUTOSENSE) { |
1da177e4 LT |
988 | /* OOPS: bad device, returning another |
989 | * contingent allegiance condition */ | |
017560fc JG |
990 | scmd_printk(KERN_ERR, SCp, |
991 | "broken device is looping in contingent allegiance: ignoring\n"); | |
1da177e4 LT |
992 | NCR_700_scsi_done(hostdata, SCp, hostdata->status[0]); |
993 | } else { | |
0f13fc09 JB |
994 | char *cmnd = |
995 | NCR_700_get_sense_cmnd(SCp->device); | |
1da177e4 LT |
996 | #ifdef NCR_DEBUG |
997 | scsi_print_command(SCp); | |
998 | printk(" cmd %p has status %d, requesting sense\n", | |
999 | SCp, hostdata->status[0]); | |
1000 | #endif | |
1001 | /* we can destroy the command here | |
1002 | * because the contingent allegiance | |
1003 | * condition will cause a retry which | |
1004 | * will re-copy the command from the | |
1005 | * saved data_cmnd. We also unmap any | |
1006 | * data associated with the command | |
1007 | * here */ | |
1008 | NCR_700_unmap(hostdata, SCp, slot); | |
67d59dfd | 1009 | dma_unmap_single(hostdata->dev, slot->pCmd, |
64a87b24 | 1010 | MAX_COMMAND_SIZE, |
67d59dfd JB |
1011 | DMA_TO_DEVICE); |
1012 | ||
0f13fc09 | 1013 | cmnd[0] = REQUEST_SENSE; |
9cb78c16 | 1014 | cmnd[1] = (lun & 0x7) << 5; |
0f13fc09 JB |
1015 | cmnd[2] = 0; |
1016 | cmnd[3] = 0; | |
b80ca4f7 | 1017 | cmnd[4] = SCSI_SENSE_BUFFERSIZE; |
0f13fc09 | 1018 | cmnd[5] = 0; |
1da177e4 LT |
1019 | /* Here's a quiet hack: the |
1020 | * REQUEST_SENSE command is six bytes, | |
1021 | * so store a flag indicating that | |
1022 | * this was an internal sense request | |
1023 | * and the original status at the end | |
1024 | * of the command */ | |
0f13fc09 JB |
1025 | cmnd[6] = NCR_700_INTERNAL_SENSE_MAGIC; |
1026 | cmnd[7] = hostdata->status[0]; | |
c603d04e JB |
1027 | cmnd[8] = SCp->cmd_len; |
1028 | SCp->cmd_len = 6; /* command length for | |
1029 | * REQUEST_SENSE */ | |
0f13fc09 | 1030 | slot->pCmd = dma_map_single(hostdata->dev, cmnd, MAX_COMMAND_SIZE, DMA_TO_DEVICE); |
b80ca4f7 FT |
1031 | slot->dma_handle = dma_map_single(hostdata->dev, SCp->sense_buffer, SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); |
1032 | slot->SG[0].ins = bS_to_host(SCRIPT_MOVE_DATA_IN | SCSI_SENSE_BUFFERSIZE); | |
1da177e4 LT |
1033 | slot->SG[0].pAddr = bS_to_host(slot->dma_handle); |
1034 | slot->SG[1].ins = bS_to_host(SCRIPT_RETURN); | |
1035 | slot->SG[1].pAddr = 0; | |
1036 | slot->resume_offset = hostdata->pScript; | |
91af2dd2 CH |
1037 | dma_sync_to_dev(hostdata, slot->SG, sizeof(slot->SG[0])*2); |
1038 | dma_sync_from_dev(hostdata, SCp->sense_buffer, SCSI_SENSE_BUFFERSIZE); | |
d3fa72e4 | 1039 | |
1da177e4 LT |
1040 | /* queue the command for reissue */ |
1041 | slot->state = NCR_700_SLOT_QUEUED; | |
67d59dfd | 1042 | slot->flags = NCR_700_FLAG_AUTOSENSE; |
1da177e4 LT |
1043 | hostdata->state = NCR_700_HOST_FREE; |
1044 | hostdata->cmd = NULL; | |
1045 | } | |
1046 | } else { | |
1047 | // Currently rely on the mid layer evaluation | |
1048 | // of the tag queuing capability | |
1049 | // | |
1050 | //if(status_byte(hostdata->status[0]) == GOOD && | |
1051 | // SCp->cmnd[0] == INQUIRY && SCp->use_sg == 0) { | |
1052 | // /* Piggy back the tag queueing support | |
1053 | // * on this command */ | |
1054 | // dma_sync_single_for_cpu(hostdata->dev, | |
1055 | // slot->dma_handle, | |
1056 | // SCp->request_bufflen, | |
1057 | // DMA_FROM_DEVICE); | |
1058 | // if(((char *)SCp->request_buffer)[7] & 0x02) { | |
017560fc JG |
1059 | // scmd_printk(KERN_INFO, SCp, |
1060 | // "Enabling Tag Command Queuing\n"); | |
1061 | // hostdata->tag_negotiated |= (1<<scmd_id(SCp)); | |
1da177e4 LT |
1062 | // NCR_700_set_flag(SCp->device, NCR_700_DEV_BEGIN_TAG_QUEUEING); |
1063 | // } else { | |
1064 | // NCR_700_clear_flag(SCp->device, NCR_700_DEV_BEGIN_TAG_QUEUEING); | |
017560fc | 1065 | // hostdata->tag_negotiated &= ~(1<<scmd_id(SCp)); |
1da177e4 LT |
1066 | // } |
1067 | //} | |
1068 | NCR_700_scsi_done(hostdata, SCp, hostdata->status[0]); | |
1069 | } | |
1070 | } else if((dsps & 0xfffff0f0) == A_UNEXPECTED_PHASE) { | |
1071 | __u8 i = (dsps & 0xf00) >> 8; | |
1072 | ||
017560fc | 1073 | scmd_printk(KERN_ERR, SCp, "UNEXPECTED PHASE %s (%s)\n", |
1da177e4 LT |
1074 | NCR_700_phase[i], |
1075 | sbcl_to_string(NCR_700_readb(host, SBCL_REG))); | |
017560fc JG |
1076 | scmd_printk(KERN_ERR, SCp, " len = %d, cmd =", |
1077 | SCp->cmd_len); | |
1da177e4 LT |
1078 | scsi_print_command(SCp); |
1079 | ||
1080 | NCR_700_internal_bus_reset(host); | |
1081 | } else if((dsps & 0xfffff000) == A_FATAL) { | |
1082 | int i = (dsps & 0xfff); | |
1083 | ||
1084 | printk(KERN_ERR "scsi%d: (%d:%d) FATAL ERROR: %s\n", | |
1085 | host->host_no, pun, lun, NCR_700_fatal_messages[i]); | |
1086 | if(dsps == A_FATAL_ILLEGAL_MSG_LENGTH) { | |
1087 | printk(KERN_ERR " msg begins %02x %02x\n", | |
1088 | hostdata->msgin[0], hostdata->msgin[1]); | |
1089 | } | |
1090 | NCR_700_internal_bus_reset(host); | |
1091 | } else if((dsps & 0xfffff0f0) == A_DISCONNECT) { | |
1092 | #ifdef NCR_700_DEBUG | |
1093 | __u8 i = (dsps & 0xf00) >> 8; | |
1094 | ||
1095 | printk("scsi%d: (%d:%d), DISCONNECTED (%d) %s\n", | |
1096 | host->host_no, pun, lun, | |
1097 | i, NCR_700_phase[i]); | |
1098 | #endif | |
1099 | save_for_reselection(hostdata, SCp, dsp); | |
1100 | ||
1101 | } else if(dsps == A_RESELECTION_IDENTIFIED) { | |
1102 | __u8 lun; | |
1103 | struct NCR_700_command_slot *slot; | |
1104 | __u8 reselection_id = hostdata->reselection_id; | |
1105 | struct scsi_device *SDp; | |
1106 | ||
1107 | lun = hostdata->msgin[0] & 0x1f; | |
1108 | ||
1109 | hostdata->reselection_id = 0xff; | |
1110 | DEBUG(("scsi%d: (%d:%d) RESELECTED!\n", | |
1111 | host->host_no, reselection_id, lun)); | |
1112 | /* clear the reselection indicator */ | |
1113 | SDp = __scsi_device_lookup(host, 0, reselection_id, lun); | |
1114 | if(unlikely(SDp == NULL)) { | |
1115 | printk(KERN_ERR "scsi%d: (%d:%d) HAS NO device\n", | |
1116 | host->host_no, reselection_id, lun); | |
1117 | BUG(); | |
1118 | } | |
1119 | if(hostdata->msgin[1] == A_SIMPLE_TAG_MSG) { | |
64d513ac CH |
1120 | struct scsi_cmnd *SCp; |
1121 | ||
1122 | SCp = scsi_host_find_tag(SDp->host, hostdata->msgin[2]); | |
1da177e4 LT |
1123 | if(unlikely(SCp == NULL)) { |
1124 | printk(KERN_ERR "scsi%d: (%d:%d) no saved request for tag %d\n", | |
1125 | host->host_no, reselection_id, lun, hostdata->msgin[2]); | |
1126 | BUG(); | |
1127 | } | |
1128 | ||
1129 | slot = (struct NCR_700_command_slot *)SCp->host_scribble; | |
017560fc JG |
1130 | DDEBUG(KERN_DEBUG, SDp, |
1131 | "reselection is tag %d, slot %p(%d)\n", | |
1132 | hostdata->msgin[2], slot, slot->tag); | |
1da177e4 | 1133 | } else { |
68350a88 CH |
1134 | struct NCR_700_Device_Parameters *p = SDp->hostdata; |
1135 | struct scsi_cmnd *SCp = p->current_cmnd; | |
64d513ac | 1136 | |
1da177e4 | 1137 | if(unlikely(SCp == NULL)) { |
017560fc JG |
1138 | sdev_printk(KERN_ERR, SDp, |
1139 | "no saved request for untagged cmd\n"); | |
1da177e4 LT |
1140 | BUG(); |
1141 | } | |
1142 | slot = (struct NCR_700_command_slot *)SCp->host_scribble; | |
1143 | } | |
1144 | ||
1145 | if(slot == NULL) { | |
1146 | printk(KERN_ERR "scsi%d: (%d:%d) RESELECTED but no saved command (MSG = %02x %02x %02x)!!\n", | |
1147 | host->host_no, reselection_id, lun, | |
1148 | hostdata->msgin[0], hostdata->msgin[1], | |
1149 | hostdata->msgin[2]); | |
1150 | } else { | |
1151 | if(hostdata->state != NCR_700_HOST_BUSY) | |
1152 | printk(KERN_ERR "scsi%d: FATAL, host not busy during valid reselection!\n", | |
1153 | host->host_no); | |
1154 | resume_offset = slot->resume_offset; | |
1155 | hostdata->cmd = slot->cmnd; | |
1156 | ||
1157 | /* re-patch for this command */ | |
91af2dd2 | 1158 | script_patch_32_abs(hostdata, hostdata->script, |
d3fa72e4 | 1159 | CommandAddress, slot->pCmd); |
91af2dd2 | 1160 | script_patch_16(hostdata, hostdata->script, |
1da177e4 | 1161 | CommandCount, slot->cmnd->cmd_len); |
91af2dd2 | 1162 | script_patch_32_abs(hostdata, hostdata->script, |
d3fa72e4 | 1163 | SGScriptStartAddress, |
1da177e4 LT |
1164 | to32bit(&slot->pSG[0].ins)); |
1165 | ||
1166 | /* Note: setting SXFER only works if we're | |
1167 | * still in the MESSAGE phase, so it is vital | |
1168 | * that ACK is still asserted when we process | |
1169 | * the reselection message. The resume offset | |
1170 | * should therefore always clear ACK */ | |
1171 | NCR_700_writeb(NCR_700_get_SXFER(hostdata->cmd->device), | |
1172 | host, SXFER_REG); | |
91af2dd2 CH |
1173 | dma_sync_from_dev(hostdata, hostdata->msgin, |
1174 | MSG_ARRAY_SIZE); | |
1175 | dma_sync_to_dev(hostdata, hostdata->msgout, | |
1176 | MSG_ARRAY_SIZE); | |
1da177e4 LT |
1177 | /* I'm just being paranoid here, the command should |
1178 | * already have been flushed from the cache */ | |
91af2dd2 CH |
1179 | dma_sync_to_dev(hostdata, slot->cmnd->cmnd, |
1180 | slot->cmnd->cmd_len); | |
1da177e4 LT |
1181 | |
1182 | ||
1183 | ||
1184 | } | |
1185 | } else if(dsps == A_RESELECTED_DURING_SELECTION) { | |
1186 | ||
1187 | /* This section is full of debugging code because I've | |
1188 | * never managed to reach it. I think what happens is | |
1189 | * that, because the 700 runs with selection | |
1190 | * interrupts enabled the whole time that we take a | |
1191 | * selection interrupt before we manage to get to the | |
1192 | * reselected script interrupt */ | |
1193 | ||
1194 | __u8 reselection_id = NCR_700_readb(host, SFBR_REG); | |
1195 | struct NCR_700_command_slot *slot; | |
1196 | ||
1197 | /* Take out our own ID */ | |
1198 | reselection_id &= ~(1<<host->this_id); | |
1199 | ||
1200 | /* I've never seen this happen, so keep this as a printk rather | |
1201 | * than a debug */ | |
1202 | printk(KERN_INFO "scsi%d: (%d:%d) RESELECTION DURING SELECTION, dsp=%08x[%04x] state=%d, count=%d\n", | |
1203 | host->host_no, reselection_id, lun, dsp, dsp - hostdata->pScript, hostdata->state, hostdata->command_slot_count); | |
1204 | ||
1205 | { | |
1206 | /* FIXME: DEBUGGING CODE */ | |
1207 | __u32 SG = (__u32)bS_to_cpu(hostdata->script[A_SGScriptStartAddress_used[0]]); | |
1208 | int i; | |
1209 | ||
1210 | for(i=0; i< NCR_700_COMMAND_SLOTS_PER_HOST; i++) { | |
1211 | if(SG >= to32bit(&hostdata->slots[i].pSG[0]) | |
1212 | && SG <= to32bit(&hostdata->slots[i].pSG[NCR_700_SG_SEGMENTS])) | |
1213 | break; | |
1214 | } | |
1215 | printk(KERN_INFO "IDENTIFIED SG segment as being %08x in slot %p, cmd %p, slot->resume_offset=%08x\n", SG, &hostdata->slots[i], hostdata->slots[i].cmnd, hostdata->slots[i].resume_offset); | |
1216 | SCp = hostdata->slots[i].cmnd; | |
1217 | } | |
1218 | ||
1219 | if(SCp != NULL) { | |
1220 | slot = (struct NCR_700_command_slot *)SCp->host_scribble; | |
1221 | /* change slot from busy to queued to redo command */ | |
1222 | slot->state = NCR_700_SLOT_QUEUED; | |
1223 | } | |
1224 | hostdata->cmd = NULL; | |
1225 | ||
1226 | if(reselection_id == 0) { | |
1227 | if(hostdata->reselection_id == 0xff) { | |
1228 | printk(KERN_ERR "scsi%d: Invalid reselection during selection!!\n", host->host_no); | |
1229 | return 0; | |
1230 | } else { | |
1231 | printk(KERN_ERR "scsi%d: script reselected and we took a selection interrupt\n", | |
1232 | host->host_no); | |
1233 | reselection_id = hostdata->reselection_id; | |
1234 | } | |
1235 | } else { | |
1236 | ||
1237 | /* convert to real ID */ | |
1238 | reselection_id = bitmap_to_number(reselection_id); | |
1239 | } | |
1240 | hostdata->reselection_id = reselection_id; | |
1241 | /* just in case we have a stale simple tag message, clear it */ | |
1242 | hostdata->msgin[1] = 0; | |
91af2dd2 | 1243 | dma_sync_to_dev(hostdata, hostdata->msgin, MSG_ARRAY_SIZE); |
1da177e4 LT |
1244 | if(hostdata->tag_negotiated & (1<<reselection_id)) { |
1245 | resume_offset = hostdata->pScript + Ent_GetReselectionWithTag; | |
1246 | } else { | |
1247 | resume_offset = hostdata->pScript + Ent_GetReselectionData; | |
1248 | } | |
1249 | } else if(dsps == A_COMPLETED_SELECTION_AS_TARGET) { | |
1250 | /* we've just disconnected from the bus, do nothing since | |
1251 | * a return here will re-run the queued command slot | |
1252 | * that may have been interrupted by the initial selection */ | |
1253 | DEBUG((" SELECTION COMPLETED\n")); | |
1254 | } else if((dsps & 0xfffff0f0) == A_MSG_IN) { | |
1255 | resume_offset = process_message(host, hostdata, SCp, | |
1256 | dsp, dsps); | |
1257 | } else if((dsps & 0xfffff000) == 0) { | |
1258 | __u8 i = (dsps & 0xf0) >> 4, j = (dsps & 0xf00) >> 8; | |
1259 | printk(KERN_ERR "scsi%d: (%d:%d), unhandled script condition %s %s at %04x\n", | |
1260 | host->host_no, pun, lun, NCR_700_condition[i], | |
1261 | NCR_700_phase[j], dsp - hostdata->pScript); | |
1262 | if(SCp != NULL) { | |
3258a4d5 | 1263 | struct scatterlist *sg; |
1da177e4 | 1264 | |
3258a4d5 FT |
1265 | scsi_print_command(SCp); |
1266 | scsi_for_each_sg(SCp, sg, scsi_sg_count(SCp) + 1, i) { | |
1267 | printk(KERN_INFO " SG[%d].length = %d, move_insn=%08x, addr %08x\n", i, sg->length, ((struct NCR_700_command_slot *)SCp->host_scribble)->SG[i].ins, ((struct NCR_700_command_slot *)SCp->host_scribble)->SG[i].pAddr); | |
1da177e4 | 1268 | } |
3258a4d5 | 1269 | } |
1da177e4 LT |
1270 | NCR_700_internal_bus_reset(host); |
1271 | } else if((dsps & 0xfffff000) == A_DEBUG_INTERRUPT) { | |
1272 | printk(KERN_NOTICE "scsi%d (%d:%d) DEBUG INTERRUPT %d AT %08x[%04x], continuing\n", | |
1273 | host->host_no, pun, lun, dsps & 0xfff, dsp, dsp - hostdata->pScript); | |
1274 | resume_offset = dsp; | |
1275 | } else { | |
1276 | printk(KERN_ERR "scsi%d: (%d:%d), unidentified script interrupt 0x%x at %04x\n", | |
1277 | host->host_no, pun, lun, dsps, dsp - hostdata->pScript); | |
1278 | NCR_700_internal_bus_reset(host); | |
1279 | } | |
1280 | return resume_offset; | |
1281 | } | |
1282 | ||
1283 | /* We run the 53c700 with selection interrupts always enabled. This | |
1284 | * means that the chip may be selected as soon as the bus frees. On a | |
1285 | * busy bus, this can be before the scripts engine finishes its | |
1286 | * processing. Therefore, part of the selection processing has to be | |
1287 | * to find out what the scripts engine is doing and complete the | |
1288 | * function if necessary (i.e. process the pending disconnect or save | |
1289 | * the interrupted initial selection */ | |
1290 | STATIC inline __u32 | |
1291 | process_selection(struct Scsi_Host *host, __u32 dsp) | |
1292 | { | |
1293 | __u8 id = 0; /* Squash compiler warning */ | |
1294 | int count = 0; | |
1295 | __u32 resume_offset = 0; | |
1296 | struct NCR_700_Host_Parameters *hostdata = | |
1297 | (struct NCR_700_Host_Parameters *)host->hostdata[0]; | |
1298 | struct scsi_cmnd *SCp = hostdata->cmd; | |
1299 | __u8 sbcl; | |
1300 | ||
1301 | for(count = 0; count < 5; count++) { | |
1302 | id = NCR_700_readb(host, hostdata->chip710 ? | |
1303 | CTEST9_REG : SFBR_REG); | |
1304 | ||
1305 | /* Take out our own ID */ | |
1306 | id &= ~(1<<host->this_id); | |
1307 | if(id != 0) | |
1308 | break; | |
1309 | udelay(5); | |
1310 | } | |
1311 | sbcl = NCR_700_readb(host, SBCL_REG); | |
1312 | if((sbcl & SBCL_IO) == 0) { | |
1313 | /* mark as having been selected rather than reselected */ | |
1314 | id = 0xff; | |
1315 | } else { | |
1316 | /* convert to real ID */ | |
1317 | hostdata->reselection_id = id = bitmap_to_number(id); | |
1318 | DEBUG(("scsi%d: Reselected by %d\n", | |
1319 | host->host_no, id)); | |
1320 | } | |
1321 | if(hostdata->state == NCR_700_HOST_BUSY && SCp != NULL) { | |
1322 | struct NCR_700_command_slot *slot = | |
1323 | (struct NCR_700_command_slot *)SCp->host_scribble; | |
1324 | DEBUG((" ID %d WARNING: RESELECTION OF BUSY HOST, saving cmd %p, slot %p, addr %x [%04x], resume %x!\n", id, hostdata->cmd, slot, dsp, dsp - hostdata->pScript, resume_offset)); | |
1325 | ||
1326 | switch(dsp - hostdata->pScript) { | |
1327 | case Ent_Disconnect1: | |
1328 | case Ent_Disconnect2: | |
1329 | save_for_reselection(hostdata, SCp, Ent_Disconnect2 + hostdata->pScript); | |
1330 | break; | |
1331 | case Ent_Disconnect3: | |
1332 | case Ent_Disconnect4: | |
1333 | save_for_reselection(hostdata, SCp, Ent_Disconnect4 + hostdata->pScript); | |
1334 | break; | |
1335 | case Ent_Disconnect5: | |
1336 | case Ent_Disconnect6: | |
1337 | save_for_reselection(hostdata, SCp, Ent_Disconnect6 + hostdata->pScript); | |
1338 | break; | |
1339 | case Ent_Disconnect7: | |
1340 | case Ent_Disconnect8: | |
1341 | save_for_reselection(hostdata, SCp, Ent_Disconnect8 + hostdata->pScript); | |
1342 | break; | |
1343 | case Ent_Finish1: | |
1344 | case Ent_Finish2: | |
1345 | process_script_interrupt(A_GOOD_STATUS_AFTER_STATUS, dsp, SCp, host, hostdata); | |
1346 | break; | |
1347 | ||
1348 | default: | |
1349 | slot->state = NCR_700_SLOT_QUEUED; | |
1350 | break; | |
1351 | } | |
1352 | } | |
1353 | hostdata->state = NCR_700_HOST_BUSY; | |
1354 | hostdata->cmd = NULL; | |
1355 | /* clear any stale simple tag message */ | |
1356 | hostdata->msgin[1] = 0; | |
91af2dd2 | 1357 | dma_sync_to_dev(hostdata, hostdata->msgin, MSG_ARRAY_SIZE); |
1da177e4 LT |
1358 | |
1359 | if(id == 0xff) { | |
1360 | /* Selected as target, Ignore */ | |
1361 | resume_offset = hostdata->pScript + Ent_SelectedAsTarget; | |
1362 | } else if(hostdata->tag_negotiated & (1<<id)) { | |
1363 | resume_offset = hostdata->pScript + Ent_GetReselectionWithTag; | |
1364 | } else { | |
1365 | resume_offset = hostdata->pScript + Ent_GetReselectionData; | |
1366 | } | |
1367 | return resume_offset; | |
1368 | } | |
1369 | ||
1370 | static inline void | |
1371 | NCR_700_clear_fifo(struct Scsi_Host *host) { | |
1372 | const struct NCR_700_Host_Parameters *hostdata | |
1373 | = (struct NCR_700_Host_Parameters *)host->hostdata[0]; | |
1374 | if(hostdata->chip710) { | |
1375 | NCR_700_writeb(CLR_FIFO_710, host, CTEST8_REG); | |
1376 | } else { | |
1377 | NCR_700_writeb(CLR_FIFO, host, DFIFO_REG); | |
1378 | } | |
1379 | } | |
1380 | ||
1381 | static inline void | |
1382 | NCR_700_flush_fifo(struct Scsi_Host *host) { | |
1383 | const struct NCR_700_Host_Parameters *hostdata | |
1384 | = (struct NCR_700_Host_Parameters *)host->hostdata[0]; | |
1385 | if(hostdata->chip710) { | |
1386 | NCR_700_writeb(FLUSH_DMA_FIFO_710, host, CTEST8_REG); | |
1387 | udelay(10); | |
1388 | NCR_700_writeb(0, host, CTEST8_REG); | |
1389 | } else { | |
1390 | NCR_700_writeb(FLUSH_DMA_FIFO, host, DFIFO_REG); | |
1391 | udelay(10); | |
1392 | NCR_700_writeb(0, host, DFIFO_REG); | |
1393 | } | |
1394 | } | |
1395 | ||
1396 | ||
1397 | /* The queue lock with interrupts disabled must be held on entry to | |
1398 | * this function */ | |
1399 | STATIC int | |
1400 | NCR_700_start_command(struct scsi_cmnd *SCp) | |
1401 | { | |
1402 | struct NCR_700_command_slot *slot = | |
1403 | (struct NCR_700_command_slot *)SCp->host_scribble; | |
1404 | struct NCR_700_Host_Parameters *hostdata = | |
1405 | (struct NCR_700_Host_Parameters *)SCp->device->host->hostdata[0]; | |
1406 | __u16 count = 1; /* for IDENTIFY message */ | |
9cb78c16 HR |
1407 | u8 lun = SCp->device->lun; |
1408 | ||
1da177e4 LT |
1409 | if(hostdata->state != NCR_700_HOST_FREE) { |
1410 | /* keep this inside the lock to close the race window where | |
1411 | * the running command finishes on another CPU while we don't | |
1412 | * change the state to queued on this one */ | |
1413 | slot->state = NCR_700_SLOT_QUEUED; | |
1414 | ||
1415 | DEBUG(("scsi%d: host busy, queueing command %p, slot %p\n", | |
1416 | SCp->device->host->host_no, slot->cmnd, slot)); | |
1417 | return 0; | |
1418 | } | |
1419 | hostdata->state = NCR_700_HOST_BUSY; | |
1420 | hostdata->cmd = SCp; | |
1421 | slot->state = NCR_700_SLOT_BUSY; | |
1422 | /* keep interrupts disabled until we have the command correctly | |
1423 | * set up so we cannot take a selection interrupt */ | |
1424 | ||
67d59dfd JB |
1425 | hostdata->msgout[0] = NCR_700_identify((SCp->cmnd[0] != REQUEST_SENSE && |
1426 | slot->flags != NCR_700_FLAG_AUTOSENSE), | |
9cb78c16 | 1427 | lun); |
1da177e4 LT |
1428 | /* for INQUIRY or REQUEST_SENSE commands, we cannot be sure |
1429 | * if the negotiated transfer parameters still hold, so | |
1430 | * always renegotiate them */ | |
67d59dfd JB |
1431 | if(SCp->cmnd[0] == INQUIRY || SCp->cmnd[0] == REQUEST_SENSE || |
1432 | slot->flags == NCR_700_FLAG_AUTOSENSE) { | |
1da177e4 LT |
1433 | NCR_700_clear_flag(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC); |
1434 | } | |
1435 | ||
1436 | /* REQUEST_SENSE is asking for contingent I_T_L(_Q) status. | |
1437 | * If a contingent allegiance condition exists, the device | |
1438 | * will refuse all tags, so send the request sense as untagged | |
1439 | * */ | |
422c0d61 | 1440 | if((hostdata->tag_negotiated & (1<<scmd_id(SCp))) |
67d59dfd JB |
1441 | && (slot->tag != SCSI_NO_TAG && SCp->cmnd[0] != REQUEST_SENSE && |
1442 | slot->flags != NCR_700_FLAG_AUTOSENSE)) { | |
50668633 | 1443 | count += spi_populate_tag_msg(&hostdata->msgout[count], SCp); |
1da177e4 LT |
1444 | } |
1445 | ||
1446 | if(hostdata->fast && | |
1447 | NCR_700_is_flag_clear(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC)) { | |
6ea3c0b2 MW |
1448 | count += spi_populate_sync_msg(&hostdata->msgout[count], |
1449 | spi_period(SCp->device->sdev_target), | |
1450 | spi_offset(SCp->device->sdev_target)); | |
1da177e4 LT |
1451 | NCR_700_set_flag(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); |
1452 | } | |
1453 | ||
91af2dd2 | 1454 | script_patch_16(hostdata, hostdata->script, MessageCount, count); |
1da177e4 | 1455 | |
91af2dd2 | 1456 | script_patch_ID(hostdata, hostdata->script, Device_ID, 1<<scmd_id(SCp)); |
1da177e4 | 1457 | |
91af2dd2 | 1458 | script_patch_32_abs(hostdata, hostdata->script, CommandAddress, |
1da177e4 | 1459 | slot->pCmd); |
91af2dd2 | 1460 | script_patch_16(hostdata, hostdata->script, CommandCount, SCp->cmd_len); |
1da177e4 LT |
1461 | /* finally plumb the beginning of the SG list into the script |
1462 | * */ | |
91af2dd2 | 1463 | script_patch_32_abs(hostdata, hostdata->script, |
d3fa72e4 | 1464 | SGScriptStartAddress, to32bit(&slot->pSG[0].ins)); |
1da177e4 LT |
1465 | NCR_700_clear_fifo(SCp->device->host); |
1466 | ||
1467 | if(slot->resume_offset == 0) | |
1468 | slot->resume_offset = hostdata->pScript; | |
1469 | /* now perform all the writebacks and invalidates */ | |
91af2dd2 CH |
1470 | dma_sync_to_dev(hostdata, hostdata->msgout, count); |
1471 | dma_sync_from_dev(hostdata, hostdata->msgin, MSG_ARRAY_SIZE); | |
1472 | dma_sync_to_dev(hostdata, SCp->cmnd, SCp->cmd_len); | |
1473 | dma_sync_from_dev(hostdata, hostdata->status, 1); | |
1da177e4 LT |
1474 | |
1475 | /* set the synchronous period/offset */ | |
1476 | NCR_700_writeb(NCR_700_get_SXFER(SCp->device), | |
1477 | SCp->device->host, SXFER_REG); | |
1478 | NCR_700_writel(slot->temp, SCp->device->host, TEMP_REG); | |
1479 | NCR_700_writel(slot->resume_offset, SCp->device->host, DSP_REG); | |
1480 | ||
1481 | return 1; | |
1482 | } | |
1483 | ||
1484 | irqreturn_t | |
7d12e780 | 1485 | NCR_700_intr(int irq, void *dev_id) |
1da177e4 LT |
1486 | { |
1487 | struct Scsi_Host *host = (struct Scsi_Host *)dev_id; | |
1488 | struct NCR_700_Host_Parameters *hostdata = | |
1489 | (struct NCR_700_Host_Parameters *)host->hostdata[0]; | |
1490 | __u8 istat; | |
1491 | __u32 resume_offset = 0; | |
1492 | __u8 pun = 0xff, lun = 0xff; | |
1493 | unsigned long flags; | |
1494 | int handled = 0; | |
1495 | ||
af901ca1 | 1496 | /* Use the host lock to serialise access to the 53c700 |
1da177e4 LT |
1497 | * hardware. Note: In future, we may need to take the queue |
1498 | * lock to enter the done routines. When that happens, we | |
1499 | * need to ensure that for this driver, the host lock and the | |
1500 | * queue lock point to the same thing. */ | |
1501 | spin_lock_irqsave(host->host_lock, flags); | |
1502 | if((istat = NCR_700_readb(host, ISTAT_REG)) | |
1503 | & (SCSI_INT_PENDING | DMA_INT_PENDING)) { | |
1504 | __u32 dsps; | |
1505 | __u8 sstat0 = 0, dstat = 0; | |
1506 | __u32 dsp; | |
1507 | struct scsi_cmnd *SCp = hostdata->cmd; | |
1da177e4 LT |
1508 | |
1509 | handled = 1; | |
1da177e4 LT |
1510 | |
1511 | if(istat & SCSI_INT_PENDING) { | |
1512 | udelay(10); | |
1513 | ||
1514 | sstat0 = NCR_700_readb(host, SSTAT0_REG); | |
1515 | } | |
1516 | ||
1517 | if(istat & DMA_INT_PENDING) { | |
1518 | udelay(10); | |
1519 | ||
1520 | dstat = NCR_700_readb(host, DSTAT_REG); | |
1521 | } | |
1522 | ||
1523 | dsps = NCR_700_readl(host, DSPS_REG); | |
1524 | dsp = NCR_700_readl(host, DSP_REG); | |
1525 | ||
1526 | DEBUG(("scsi%d: istat %02x sstat0 %02x dstat %02x dsp %04x[%08x] dsps 0x%x\n", | |
1527 | host->host_no, istat, sstat0, dstat, | |
1528 | (dsp - (__u32)(hostdata->pScript))/4, | |
1529 | dsp, dsps)); | |
1530 | ||
1531 | if(SCp != NULL) { | |
1532 | pun = SCp->device->id; | |
1533 | lun = SCp->device->lun; | |
1534 | } | |
1535 | ||
1536 | if(sstat0 & SCSI_RESET_DETECTED) { | |
1537 | struct scsi_device *SDp; | |
1538 | int i; | |
1539 | ||
1540 | hostdata->state = NCR_700_HOST_BUSY; | |
1541 | ||
1542 | printk(KERN_ERR "scsi%d: Bus Reset detected, executing command %p, slot %p, dsp %08x[%04x]\n", | |
1543 | host->host_no, SCp, SCp == NULL ? NULL : SCp->host_scribble, dsp, dsp - hostdata->pScript); | |
1544 | ||
1545 | scsi_report_bus_reset(host, 0); | |
1546 | ||
1547 | /* clear all the negotiated parameters */ | |
1548 | __shost_for_each_device(SDp, host) | |
0f13fc09 | 1549 | NCR_700_clear_flag(SDp, ~0); |
1da177e4 LT |
1550 | |
1551 | /* clear all the slots and their pending commands */ | |
1552 | for(i = 0; i < NCR_700_COMMAND_SLOTS_PER_HOST; i++) { | |
1553 | struct scsi_cmnd *SCp; | |
1554 | struct NCR_700_command_slot *slot = | |
1555 | &hostdata->slots[i]; | |
1556 | ||
1557 | if(slot->state == NCR_700_SLOT_FREE) | |
1558 | continue; | |
1559 | ||
1560 | SCp = slot->cmnd; | |
1561 | printk(KERN_ERR " failing command because of reset, slot %p, cmnd %p\n", | |
1562 | slot, SCp); | |
1563 | free_slot(slot, hostdata); | |
1564 | SCp->host_scribble = NULL; | |
1565 | NCR_700_set_depth(SCp->device, 0); | |
1566 | /* NOTE: deadlock potential here: we | |
1567 | * rely on mid-layer guarantees that | |
1568 | * scsi_done won't try to issue the | |
1569 | * command again otherwise we'll | |
1570 | * deadlock on the | |
1571 | * hostdata->state_lock */ | |
1572 | SCp->result = DID_RESET << 16; | |
656f26ad | 1573 | scsi_done(SCp); |
1da177e4 LT |
1574 | } |
1575 | mdelay(25); | |
1576 | NCR_700_chip_setup(host); | |
1577 | ||
1578 | hostdata->state = NCR_700_HOST_FREE; | |
1579 | hostdata->cmd = NULL; | |
1580 | /* signal back if this was an eh induced reset */ | |
1581 | if(hostdata->eh_complete != NULL) | |
1582 | complete(hostdata->eh_complete); | |
1583 | goto out_unlock; | |
1584 | } else if(sstat0 & SELECTION_TIMEOUT) { | |
1585 | DEBUG(("scsi%d: (%d:%d) selection timeout\n", | |
1586 | host->host_no, pun, lun)); | |
1587 | NCR_700_scsi_done(hostdata, SCp, DID_NO_CONNECT<<16); | |
1588 | } else if(sstat0 & PHASE_MISMATCH) { | |
1589 | struct NCR_700_command_slot *slot = (SCp == NULL) ? NULL : | |
1590 | (struct NCR_700_command_slot *)SCp->host_scribble; | |
1591 | ||
1592 | if(dsp == Ent_SendMessage + 8 + hostdata->pScript) { | |
1593 | /* It wants to reply to some part of | |
1594 | * our message */ | |
1595 | #ifdef NCR_700_DEBUG | |
1596 | __u32 temp = NCR_700_readl(host, TEMP_REG); | |
1597 | int count = (hostdata->script[Ent_SendMessage/4] & 0xffffff) - ((NCR_700_readl(host, DBC_REG) & 0xffffff) + NCR_700_data_residual(host)); | |
1598 | printk("scsi%d (%d:%d) PHASE MISMATCH IN SEND MESSAGE %d remain, return %p[%04x], phase %s\n", host->host_no, pun, lun, count, (void *)temp, temp - hostdata->pScript, sbcl_to_string(NCR_700_readb(host, SBCL_REG))); | |
1599 | #endif | |
1600 | resume_offset = hostdata->pScript + Ent_SendMessagePhaseMismatch; | |
1601 | } else if(dsp >= to32bit(&slot->pSG[0].ins) && | |
1602 | dsp <= to32bit(&slot->pSG[NCR_700_SG_SEGMENTS].ins)) { | |
1603 | int data_transfer = NCR_700_readl(host, DBC_REG) & 0xffffff; | |
1604 | int SGcount = (dsp - to32bit(&slot->pSG[0].ins))/sizeof(struct NCR_700_SG_List); | |
1605 | int residual = NCR_700_data_residual(host); | |
1606 | int i; | |
1607 | #ifdef NCR_700_DEBUG | |
1608 | __u32 naddr = NCR_700_readl(host, DNAD_REG); | |
1609 | ||
1610 | printk("scsi%d: (%d:%d) Expected phase mismatch in slot->SG[%d], transferred 0x%x\n", | |
1611 | host->host_no, pun, lun, | |
1612 | SGcount, data_transfer); | |
1613 | scsi_print_command(SCp); | |
1614 | if(residual) { | |
1615 | printk("scsi%d: (%d:%d) Expected phase mismatch in slot->SG[%d], transferred 0x%x, residual %d\n", | |
1616 | host->host_no, pun, lun, | |
1617 | SGcount, data_transfer, residual); | |
1618 | } | |
1619 | #endif | |
1620 | data_transfer += residual; | |
1621 | ||
1622 | if(data_transfer != 0) { | |
1623 | int count; | |
1624 | __u32 pAddr; | |
1625 | ||
1626 | SGcount--; | |
1627 | ||
1628 | count = (bS_to_cpu(slot->SG[SGcount].ins) & 0x00ffffff); | |
1629 | DEBUG(("DATA TRANSFER MISMATCH, count = %d, transferred %d\n", count, count-data_transfer)); | |
1630 | slot->SG[SGcount].ins &= bS_to_host(0xff000000); | |
1631 | slot->SG[SGcount].ins |= bS_to_host(data_transfer); | |
1632 | pAddr = bS_to_cpu(slot->SG[SGcount].pAddr); | |
1633 | pAddr += (count - data_transfer); | |
1634 | #ifdef NCR_700_DEBUG | |
1635 | if(pAddr != naddr) { | |
1636 | printk("scsi%d (%d:%d) transfer mismatch pAddr=%lx, naddr=%lx, data_transfer=%d, residual=%d\n", host->host_no, pun, lun, (unsigned long)pAddr, (unsigned long)naddr, data_transfer, residual); | |
1637 | } | |
1638 | #endif | |
1639 | slot->SG[SGcount].pAddr = bS_to_host(pAddr); | |
1640 | } | |
1641 | /* set the executed moves to nops */ | |
1642 | for(i=0; i<SGcount; i++) { | |
1643 | slot->SG[i].ins = bS_to_host(SCRIPT_NOP); | |
1644 | slot->SG[i].pAddr = 0; | |
1645 | } | |
91af2dd2 | 1646 | dma_sync_to_dev(hostdata, slot->SG, sizeof(slot->SG)); |
1da177e4 LT |
1647 | /* and pretend we disconnected after |
1648 | * the command phase */ | |
1649 | resume_offset = hostdata->pScript + Ent_MsgInDuringData; | |
1650 | /* make sure all the data is flushed */ | |
1651 | NCR_700_flush_fifo(host); | |
1652 | } else { | |
1653 | __u8 sbcl = NCR_700_readb(host, SBCL_REG); | |
1654 | printk(KERN_ERR "scsi%d: (%d:%d) phase mismatch at %04x, phase %s\n", | |
1655 | host->host_no, pun, lun, dsp - hostdata->pScript, sbcl_to_string(sbcl)); | |
1656 | NCR_700_internal_bus_reset(host); | |
1657 | } | |
1658 | ||
1659 | } else if(sstat0 & SCSI_GROSS_ERROR) { | |
1660 | printk(KERN_ERR "scsi%d: (%d:%d) GROSS ERROR\n", | |
1661 | host->host_no, pun, lun); | |
1662 | NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); | |
1663 | } else if(sstat0 & PARITY_ERROR) { | |
1664 | printk(KERN_ERR "scsi%d: (%d:%d) PARITY ERROR\n", | |
1665 | host->host_no, pun, lun); | |
1666 | NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); | |
1667 | } else if(dstat & SCRIPT_INT_RECEIVED) { | |
1668 | DEBUG(("scsi%d: (%d:%d) ====>SCRIPT INTERRUPT<====\n", | |
1669 | host->host_no, pun, lun)); | |
1670 | resume_offset = process_script_interrupt(dsps, dsp, SCp, host, hostdata); | |
1671 | } else if(dstat & (ILGL_INST_DETECTED)) { | |
1672 | printk(KERN_ERR "scsi%d: (%d:%d) Illegal Instruction detected at 0x%08x[0x%x]!!!\n" | |
1673 | " Please email James.Bottomley@HansenPartnership.com with the details\n", | |
1674 | host->host_no, pun, lun, | |
1675 | dsp, dsp - hostdata->pScript); | |
1676 | NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); | |
1677 | } else if(dstat & (WATCH_DOG_INTERRUPT|ABORTED)) { | |
1678 | printk(KERN_ERR "scsi%d: (%d:%d) serious DMA problem, dstat=%02x\n", | |
1679 | host->host_no, pun, lun, dstat); | |
1680 | NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); | |
1681 | } | |
1682 | ||
1683 | ||
1684 | /* NOTE: selection interrupt processing MUST occur | |
1685 | * after script interrupt processing to correctly cope | |
1686 | * with the case where we process a disconnect and | |
1687 | * then get reselected before we process the | |
1688 | * disconnection */ | |
1689 | if(sstat0 & SELECTED) { | |
1690 | /* FIXME: It currently takes at least FOUR | |
1691 | * interrupts to complete a command that | |
1692 | * disconnects: one for the disconnect, one | |
1693 | * for the reselection, one to get the | |
1694 | * reselection data and one to complete the | |
1695 | * command. If we guess the reselected | |
1696 | * command here and prepare it, we only need | |
1697 | * to get a reselection data interrupt if we | |
1698 | * guessed wrongly. Since the interrupt | |
1699 | * overhead is much greater than the command | |
1700 | * setup, this would be an efficient | |
1701 | * optimisation particularly as we probably | |
1702 | * only have one outstanding command on a | |
1703 | * target most of the time */ | |
1704 | ||
1705 | resume_offset = process_selection(host, dsp); | |
1706 | ||
1707 | } | |
1708 | ||
1709 | } | |
1710 | ||
1711 | if(resume_offset) { | |
1712 | if(hostdata->state != NCR_700_HOST_BUSY) { | |
1713 | printk(KERN_ERR "scsi%d: Driver error: resume at 0x%08x [0x%04x] with non busy host!\n", | |
1714 | host->host_no, resume_offset, resume_offset - hostdata->pScript); | |
1715 | hostdata->state = NCR_700_HOST_BUSY; | |
1716 | } | |
1717 | ||
1718 | DEBUG(("Attempting to resume at %x\n", resume_offset)); | |
1719 | NCR_700_clear_fifo(host); | |
1720 | NCR_700_writel(resume_offset, host, DSP_REG); | |
1721 | } | |
1722 | /* There is probably a technical no-no about this: If we're a | |
1723 | * shared interrupt and we got this interrupt because the | |
1724 | * other device needs servicing not us, we're still going to | |
1725 | * check our queued commands here---of course, there shouldn't | |
1726 | * be any outstanding.... */ | |
1727 | if(hostdata->state == NCR_700_HOST_FREE) { | |
1728 | int i; | |
1729 | ||
1730 | for(i = 0; i < NCR_700_COMMAND_SLOTS_PER_HOST; i++) { | |
1731 | /* fairness: always run the queue from the last | |
1732 | * position we left off */ | |
1733 | int j = (i + hostdata->saved_slot_position) | |
1734 | % NCR_700_COMMAND_SLOTS_PER_HOST; | |
1735 | ||
1736 | if(hostdata->slots[j].state != NCR_700_SLOT_QUEUED) | |
1737 | continue; | |
1738 | if(NCR_700_start_command(hostdata->slots[j].cmnd)) { | |
1739 | DEBUG(("scsi%d: Issuing saved command slot %p, cmd %p\t\n", | |
1740 | host->host_no, &hostdata->slots[j], | |
1741 | hostdata->slots[j].cmnd)); | |
1742 | hostdata->saved_slot_position = j + 1; | |
1743 | } | |
1744 | ||
1745 | break; | |
1746 | } | |
1747 | } | |
1748 | out_unlock: | |
1749 | spin_unlock_irqrestore(host->host_lock, flags); | |
1750 | return IRQ_RETVAL(handled); | |
1751 | } | |
1752 | ||
af049dfd | 1753 | static int NCR_700_queuecommand_lck(struct scsi_cmnd *SCp) |
1da177e4 LT |
1754 | { |
1755 | struct NCR_700_Host_Parameters *hostdata = | |
1756 | (struct NCR_700_Host_Parameters *)SCp->device->host->hostdata[0]; | |
1757 | __u32 move_ins; | |
1da177e4 LT |
1758 | struct NCR_700_command_slot *slot; |
1759 | ||
1760 | if(hostdata->command_slot_count >= NCR_700_COMMAND_SLOTS_PER_HOST) { | |
1761 | /* We're over our allocation, this should never happen | |
1762 | * since we report the max allocation to the mid layer */ | |
1763 | printk(KERN_WARNING "scsi%d: Command depth has gone over queue depth\n", SCp->device->host->host_no); | |
1764 | return 1; | |
1765 | } | |
1766 | /* check for untagged commands. We cannot have any outstanding | |
1767 | * commands if we accept them. Commands could be untagged because: | |
1768 | * | |
1769 | * - The tag negotiated bitmap is clear | |
1770 | * - The blk layer sent and untagged command | |
1771 | */ | |
1772 | if(NCR_700_get_depth(SCp->device) != 0 | |
017560fc | 1773 | && (!(hostdata->tag_negotiated & (1<<scmd_id(SCp))) |
125c99bc | 1774 | || !(SCp->flags & SCMD_TAGGED))) { |
017560fc JG |
1775 | CDEBUG(KERN_ERR, SCp, "has non zero depth %d\n", |
1776 | NCR_700_get_depth(SCp->device)); | |
1da177e4 LT |
1777 | return SCSI_MLQUEUE_DEVICE_BUSY; |
1778 | } | |
1779 | if(NCR_700_get_depth(SCp->device) >= SCp->device->queue_depth) { | |
017560fc JG |
1780 | CDEBUG(KERN_ERR, SCp, "has max tag depth %d\n", |
1781 | NCR_700_get_depth(SCp->device)); | |
1da177e4 LT |
1782 | return SCSI_MLQUEUE_DEVICE_BUSY; |
1783 | } | |
1784 | NCR_700_set_depth(SCp->device, NCR_700_get_depth(SCp->device) + 1); | |
1785 | ||
1786 | /* begin the command here */ | |
1787 | /* no need to check for NULL, test for command_slot_count above | |
1788 | * ensures a slot is free */ | |
1789 | slot = find_empty_slot(hostdata); | |
1790 | ||
1791 | slot->cmnd = SCp; | |
1792 | ||
1da177e4 | 1793 | SCp->host_scribble = (unsigned char *)slot; |
1da177e4 LT |
1794 | |
1795 | #ifdef NCR_700_DEBUG | |
1796 | printk("53c700: scsi%d, command ", SCp->device->host->host_no); | |
1797 | scsi_print_command(SCp); | |
1798 | #endif | |
125c99bc | 1799 | if ((SCp->flags & SCMD_TAGGED) |
017560fc | 1800 | && (hostdata->tag_negotiated &(1<<scmd_id(SCp))) == 0 |
1da177e4 | 1801 | && NCR_700_get_tag_neg_state(SCp->device) == NCR_700_START_TAG_NEGOTIATION) { |
017560fc JG |
1802 | scmd_printk(KERN_ERR, SCp, "Enabling Tag Command Queuing\n"); |
1803 | hostdata->tag_negotiated |= (1<<scmd_id(SCp)); | |
1da177e4 LT |
1804 | NCR_700_set_tag_neg_state(SCp->device, NCR_700_DURING_TAG_NEGOTIATION); |
1805 | } | |
1806 | ||
1807 | /* here we may have to process an untagged command. The gate | |
1808 | * above ensures that this will be the only one outstanding, | |
1809 | * so clear the tag negotiated bit. | |
1810 | * | |
1811 | * FIXME: This will royally screw up on multiple LUN devices | |
1812 | * */ | |
125c99bc | 1813 | if (!(SCp->flags & SCMD_TAGGED) |
017560fc JG |
1814 | && (hostdata->tag_negotiated &(1<<scmd_id(SCp)))) { |
1815 | scmd_printk(KERN_INFO, SCp, "Disabling Tag Command Queuing\n"); | |
1816 | hostdata->tag_negotiated &= ~(1<<scmd_id(SCp)); | |
1da177e4 LT |
1817 | } |
1818 | ||
17ea0126 CH |
1819 | if ((hostdata->tag_negotiated & (1<<scmd_id(SCp))) && |
1820 | SCp->device->simple_tags) { | |
cd4b46cd | 1821 | slot->tag = scsi_cmd_to_rq(SCp)->tag; |
017560fc JG |
1822 | CDEBUG(KERN_DEBUG, SCp, "sending out tag %d, slot %p\n", |
1823 | slot->tag, slot); | |
1da177e4 | 1824 | } else { |
68350a88 CH |
1825 | struct NCR_700_Device_Parameters *p = SCp->device->hostdata; |
1826 | ||
1da177e4 | 1827 | slot->tag = SCSI_NO_TAG; |
8beb3300 | 1828 | /* save current command for reselection */ |
68350a88 | 1829 | p->current_cmnd = SCp; |
1da177e4 LT |
1830 | } |
1831 | /* sanity check: some of the commands generated by the mid-layer | |
1832 | * have an eccentric idea of their sc_data_direction */ | |
3258a4d5 FT |
1833 | if(!scsi_sg_count(SCp) && !scsi_bufflen(SCp) && |
1834 | SCp->sc_data_direction != DMA_NONE) { | |
1da177e4 LT |
1835 | #ifdef NCR_700_DEBUG |
1836 | printk("53c700: Command"); | |
1837 | scsi_print_command(SCp); | |
1838 | printk("Has wrong data direction %d\n", SCp->sc_data_direction); | |
1839 | #endif | |
1840 | SCp->sc_data_direction = DMA_NONE; | |
1841 | } | |
1842 | ||
1843 | switch (SCp->cmnd[0]) { | |
1844 | case REQUEST_SENSE: | |
1845 | /* clear the internal sense magic */ | |
1846 | SCp->cmnd[6] = 0; | |
df561f66 | 1847 | fallthrough; |
1da177e4 LT |
1848 | default: |
1849 | /* OK, get it from the command */ | |
1850 | switch(SCp->sc_data_direction) { | |
1851 | case DMA_BIDIRECTIONAL: | |
1852 | default: | |
1853 | printk(KERN_ERR "53c700: Unknown command for data direction "); | |
1854 | scsi_print_command(SCp); | |
1855 | ||
1856 | move_ins = 0; | |
1857 | break; | |
1858 | case DMA_NONE: | |
1859 | move_ins = 0; | |
1860 | break; | |
1861 | case DMA_FROM_DEVICE: | |
1862 | move_ins = SCRIPT_MOVE_DATA_IN; | |
1863 | break; | |
1864 | case DMA_TO_DEVICE: | |
1865 | move_ins = SCRIPT_MOVE_DATA_OUT; | |
1866 | break; | |
1867 | } | |
1868 | } | |
1869 | ||
1870 | /* now build the scatter gather list */ | |
1da177e4 LT |
1871 | if(move_ins != 0) { |
1872 | int i; | |
1873 | int sg_count; | |
1874 | dma_addr_t vPtr = 0; | |
3258a4d5 | 1875 | struct scatterlist *sg; |
1da177e4 LT |
1876 | __u32 count = 0; |
1877 | ||
3258a4d5 FT |
1878 | sg_count = scsi_dma_map(SCp); |
1879 | BUG_ON(sg_count < 0); | |
1da177e4 | 1880 | |
3258a4d5 FT |
1881 | scsi_for_each_sg(SCp, sg, sg_count, i) { |
1882 | vPtr = sg_dma_address(sg); | |
1883 | count = sg_dma_len(sg); | |
1da177e4 LT |
1884 | |
1885 | slot->SG[i].ins = bS_to_host(move_ins | count); | |
1886 | DEBUG((" scatter block %d: move %d[%08x] from 0x%lx\n", | |
1887 | i, count, slot->SG[i].ins, (unsigned long)vPtr)); | |
1888 | slot->SG[i].pAddr = bS_to_host(vPtr); | |
1889 | } | |
1890 | slot->SG[i].ins = bS_to_host(SCRIPT_RETURN); | |
1891 | slot->SG[i].pAddr = 0; | |
91af2dd2 | 1892 | dma_sync_to_dev(hostdata, slot->SG, sizeof(slot->SG)); |
0da21c44 | 1893 | DEBUG((" SETTING %p to %x\n", |
d3fa72e4 | 1894 | (&slot->pSG[i].ins), |
1da177e4 LT |
1895 | slot->SG[i].ins)); |
1896 | } | |
1897 | slot->resume_offset = 0; | |
1898 | slot->pCmd = dma_map_single(hostdata->dev, SCp->cmnd, | |
64a87b24 | 1899 | MAX_COMMAND_SIZE, DMA_TO_DEVICE); |
1da177e4 LT |
1900 | NCR_700_start_command(SCp); |
1901 | return 0; | |
1902 | } | |
1903 | ||
f281233d JG |
1904 | STATIC DEF_SCSI_QCMD(NCR_700_queuecommand) |
1905 | ||
1da177e4 LT |
1906 | STATIC int |
1907 | NCR_700_abort(struct scsi_cmnd * SCp) | |
1908 | { | |
1909 | struct NCR_700_command_slot *slot; | |
1910 | ||
1fa6b5fb | 1911 | scmd_printk(KERN_INFO, SCp, "abort command\n"); |
1da177e4 LT |
1912 | |
1913 | slot = (struct NCR_700_command_slot *)SCp->host_scribble; | |
1914 | ||
1915 | if(slot == NULL) | |
1916 | /* no outstanding command to abort */ | |
1917 | return SUCCESS; | |
1918 | if(SCp->cmnd[0] == TEST_UNIT_READY) { | |
1919 | /* FIXME: This is because of a problem in the new | |
1920 | * error handler. When it is in error recovery, it | |
1921 | * will send a TUR to a device it thinks may still be | |
1922 | * showing a problem. If the TUR isn't responded to, | |
1923 | * it will abort it and mark the device off line. | |
1924 | * Unfortunately, it does no other error recovery, so | |
1925 | * this would leave us with an outstanding command | |
1926 | * occupying a slot. Rather than allow this to | |
1927 | * happen, we issue a bus reset to force all | |
1928 | * outstanding commands to terminate here. */ | |
1929 | NCR_700_internal_bus_reset(SCp->device->host); | |
1930 | /* still drop through and return failed */ | |
1931 | } | |
1932 | return FAILED; | |
1933 | ||
1934 | } | |
1935 | ||
1936 | STATIC int | |
44257a1b | 1937 | NCR_700_host_reset(struct scsi_cmnd * SCp) |
1da177e4 | 1938 | { |
6e9a4738 | 1939 | DECLARE_COMPLETION_ONSTACK(complete); |
1da177e4 LT |
1940 | struct NCR_700_Host_Parameters *hostdata = |
1941 | (struct NCR_700_Host_Parameters *)SCp->device->host->hostdata[0]; | |
1942 | ||
017560fc | 1943 | scmd_printk(KERN_INFO, SCp, |
44257a1b | 1944 | "New error handler wants HOST reset, cmd %p\n\t", SCp); |
1da177e4 | 1945 | scsi_print_command(SCp); |
68b3aa7c | 1946 | |
1da177e4 LT |
1947 | /* In theory, eh_complete should always be null because the |
1948 | * eh is single threaded, but just in case we're handling a | |
1949 | * reset via sg or something */ | |
68b3aa7c JG |
1950 | spin_lock_irq(SCp->device->host->host_lock); |
1951 | while (hostdata->eh_complete != NULL) { | |
1da177e4 LT |
1952 | spin_unlock_irq(SCp->device->host->host_lock); |
1953 | msleep_interruptible(100); | |
1954 | spin_lock_irq(SCp->device->host->host_lock); | |
1955 | } | |
68b3aa7c | 1956 | |
1da177e4 LT |
1957 | hostdata->eh_complete = &complete; |
1958 | NCR_700_internal_bus_reset(SCp->device->host); | |
44257a1b | 1959 | NCR_700_chip_reset(SCp->device->host); |
68b3aa7c | 1960 | |
1da177e4 LT |
1961 | spin_unlock_irq(SCp->device->host->host_lock); |
1962 | wait_for_completion(&complete); | |
1963 | spin_lock_irq(SCp->device->host->host_lock); | |
68b3aa7c | 1964 | |
1da177e4 LT |
1965 | hostdata->eh_complete = NULL; |
1966 | /* Revalidate the transport parameters of the failing device */ | |
1967 | if(hostdata->fast) | |
1968 | spi_schedule_dv_device(SCp->device); | |
68b3aa7c JG |
1969 | |
1970 | spin_unlock_irq(SCp->device->host->host_lock); | |
1da177e4 LT |
1971 | return SUCCESS; |
1972 | } | |
1973 | ||
1da177e4 LT |
1974 | STATIC void |
1975 | NCR_700_set_period(struct scsi_target *STp, int period) | |
1976 | { | |
1977 | struct Scsi_Host *SHp = dev_to_shost(STp->dev.parent); | |
1978 | struct NCR_700_Host_Parameters *hostdata = | |
1979 | (struct NCR_700_Host_Parameters *)SHp->hostdata[0]; | |
1980 | ||
1981 | if(!hostdata->fast) | |
1982 | return; | |
1983 | ||
1984 | if(period < hostdata->min_period) | |
1985 | period = hostdata->min_period; | |
1986 | ||
1987 | spi_period(STp) = period; | |
1988 | spi_flags(STp) &= ~(NCR_700_DEV_NEGOTIATED_SYNC | | |
1989 | NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); | |
1990 | spi_flags(STp) |= NCR_700_DEV_PRINT_SYNC_NEGOTIATION; | |
1991 | } | |
1992 | ||
1993 | STATIC void | |
1994 | NCR_700_set_offset(struct scsi_target *STp, int offset) | |
1995 | { | |
1996 | struct Scsi_Host *SHp = dev_to_shost(STp->dev.parent); | |
1997 | struct NCR_700_Host_Parameters *hostdata = | |
1998 | (struct NCR_700_Host_Parameters *)SHp->hostdata[0]; | |
1999 | int max_offset = hostdata->chip710 | |
2000 | ? NCR_710_MAX_OFFSET : NCR_700_MAX_OFFSET; | |
2001 | ||
2002 | if(!hostdata->fast) | |
2003 | return; | |
2004 | ||
2005 | if(offset > max_offset) | |
2006 | offset = max_offset; | |
2007 | ||
2008 | /* if we're currently async, make sure the period is reasonable */ | |
2009 | if(spi_offset(STp) == 0 && (spi_period(STp) < hostdata->min_period || | |
2010 | spi_period(STp) > 0xff)) | |
2011 | spi_period(STp) = hostdata->min_period; | |
2012 | ||
2013 | spi_offset(STp) = offset; | |
2014 | spi_flags(STp) &= ~(NCR_700_DEV_NEGOTIATED_SYNC | | |
2015 | NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); | |
2016 | spi_flags(STp) |= NCR_700_DEV_PRINT_SYNC_NEGOTIATION; | |
2017 | } | |
2018 | ||
0f13fc09 JB |
2019 | STATIC int |
2020 | NCR_700_slave_alloc(struct scsi_device *SDp) | |
2021 | { | |
2022 | SDp->hostdata = kzalloc(sizeof(struct NCR_700_Device_Parameters), | |
2023 | GFP_KERNEL); | |
1da177e4 | 2024 | |
0f13fc09 JB |
2025 | if (!SDp->hostdata) |
2026 | return -ENOMEM; | |
2027 | ||
2028 | return 0; | |
2029 | } | |
1da177e4 LT |
2030 | |
2031 | STATIC int | |
2032 | NCR_700_slave_configure(struct scsi_device *SDp) | |
2033 | { | |
2034 | struct NCR_700_Host_Parameters *hostdata = | |
2035 | (struct NCR_700_Host_Parameters *)SDp->host->hostdata[0]; | |
2036 | ||
2037 | /* to do here: allocate memory; build a queue_full list */ | |
2038 | if(SDp->tagged_supported) { | |
db5ed4df | 2039 | scsi_change_queue_depth(SDp, NCR_700_DEFAULT_TAGS); |
1da177e4 | 2040 | NCR_700_set_tag_neg_state(SDp, NCR_700_START_TAG_NEGOTIATION); |
1da177e4 | 2041 | } |
c8b09f6f | 2042 | |
1da177e4 LT |
2043 | if(hostdata->fast) { |
2044 | /* Find the correct offset and period via domain validation */ | |
2045 | if (!spi_initial_dv(SDp->sdev_target)) | |
2046 | spi_dv_device(SDp); | |
2047 | } else { | |
2048 | spi_offset(SDp->sdev_target) = 0; | |
2049 | spi_period(SDp->sdev_target) = 0; | |
2050 | } | |
2051 | return 0; | |
2052 | } | |
2053 | ||
2054 | STATIC void | |
2055 | NCR_700_slave_destroy(struct scsi_device *SDp) | |
2056 | { | |
67d59dfd JB |
2057 | kfree(SDp->hostdata); |
2058 | SDp->hostdata = NULL; | |
1da177e4 LT |
2059 | } |
2060 | ||
2061 | static int | |
db5ed4df | 2062 | NCR_700_change_queue_depth(struct scsi_device *SDp, int depth) |
1da177e4 LT |
2063 | { |
2064 | if (depth > NCR_700_MAX_TAGS) | |
2065 | depth = NCR_700_MAX_TAGS; | |
db5ed4df | 2066 | return scsi_change_queue_depth(SDp, depth); |
1da177e4 LT |
2067 | } |
2068 | ||
1da177e4 | 2069 | static ssize_t |
10523b3b | 2070 | NCR_700_show_active_tags(struct device *dev, struct device_attribute *attr, char *buf) |
1da177e4 LT |
2071 | { |
2072 | struct scsi_device *SDp = to_scsi_device(dev); | |
2073 | ||
2074 | return snprintf(buf, 20, "%d\n", NCR_700_get_depth(SDp)); | |
2075 | } | |
2076 | ||
2077 | static struct device_attribute NCR_700_active_tags_attr = { | |
2078 | .attr = { | |
2079 | .name = "active_tags", | |
2080 | .mode = S_IRUGO, | |
2081 | }, | |
2082 | .show = NCR_700_show_active_tags, | |
2083 | }; | |
2084 | ||
90cb6538 BVA |
2085 | STATIC struct attribute *NCR_700_dev_attrs[] = { |
2086 | &NCR_700_active_tags_attr.attr, | |
1da177e4 LT |
2087 | NULL, |
2088 | }; | |
2089 | ||
90cb6538 BVA |
2090 | ATTRIBUTE_GROUPS(NCR_700_dev); |
2091 | ||
1da177e4 LT |
2092 | EXPORT_SYMBOL(NCR_700_detect); |
2093 | EXPORT_SYMBOL(NCR_700_release); | |
2094 | EXPORT_SYMBOL(NCR_700_intr); | |
2095 | ||
2096 | static struct spi_function_template NCR_700_transport_functions = { | |
2097 | .set_period = NCR_700_set_period, | |
2098 | .show_period = 1, | |
2099 | .set_offset = NCR_700_set_offset, | |
2100 | .show_offset = 1, | |
2101 | }; | |
2102 | ||
2103 | static int __init NCR_700_init(void) | |
2104 | { | |
2105 | NCR_700_transport_template = spi_attach_transport(&NCR_700_transport_functions); | |
2106 | if(!NCR_700_transport_template) | |
2107 | return -ENODEV; | |
2108 | return 0; | |
2109 | } | |
2110 | ||
2111 | static void __exit NCR_700_exit(void) | |
2112 | { | |
2113 | spi_release_transport(NCR_700_transport_template); | |
2114 | } | |
2115 | ||
2116 | module_init(NCR_700_init); | |
2117 | module_exit(NCR_700_exit); | |
2118 |