Commit | Line | Data |
---|---|---|
e4d6b795 MB |
1 | config B43 |
2 | tristate "Broadcom 43xx wireless support (mac80211 stack)" | |
fbe057d8 RM |
3 | depends on (BCMA_POSSIBLE || SSB_POSSIBLE) && MAC80211 && HAS_DMA |
4 | select BCMA if B43_BCMA | |
5 | select SSB if B43_SSB | |
e4d6b795 | 6 | select FW_LOADER |
e4d6b795 MB |
7 | ---help--- |
8 | b43 is a driver for the Broadcom 43xx series wireless devices. | |
9 | ||
10 | Check "lspci" for something like | |
11 | "Broadcom Corporation BCM43XX 802.11 Wireless LAN Controller" | |
12 | to determine whether you own such a device. | |
13 | ||
14 | This driver supports the new BCM43xx IEEE 802.11G devices, but not | |
15 | the old IEEE 802.11B devices. Old devices are supported by | |
16 | the b43legacy driver. | |
17 | Note that this has nothing to do with the standard that your AccessPoint | |
18 | supports (A, B, G or a combination). | |
19 | IEEE 802.11G devices can talk to IEEE 802.11B AccessPoints. | |
20 | ||
21 | It is safe to include both b43 and b43legacy as the underlying glue | |
22 | layer will automatically load the correct version for your device. | |
23 | ||
24 | This driver uses V4 firmware, which must be installed separately using | |
25 | b43-fwcutter. | |
26 | ||
27 | This driver can be built as a module (recommended) that will be called "b43". | |
28 | If unsure, say M. | |
29 | ||
3c65ab62 | 30 | config B43_BCMA |
fbe057d8 | 31 | bool |
3c65ab62 | 32 | |
aec7ffdf RM |
33 | config B43_SSB |
34 | bool | |
fbe057d8 RM |
35 | |
36 | choice | |
37 | prompt "Supported bus types" | |
38 | depends on B43 | |
740bb82b | 39 | default B43_BUSES_BCMA_AND_SSB |
fbe057d8 RM |
40 | |
41 | config B43_BUSES_BCMA_AND_SSB | |
42 | bool "BCMA and SSB" | |
43 | depends on BCMA_POSSIBLE && SSB_POSSIBLE | |
44 | select B43_BCMA | |
45 | select B43_SSB | |
46 | ||
47 | config B43_BUSES_BCMA | |
48 | bool "BCMA only" | |
49 | depends on BCMA_POSSIBLE | |
50 | select B43_BCMA | |
51 | ||
52 | config B43_BUSES_SSB | |
53 | bool "SSB only" | |
54 | depends on SSB_POSSIBLE | |
55 | select B43_SSB | |
56 | ||
57 | endchoice | |
aec7ffdf | 58 | |
e4d6b795 MB |
59 | # Auto-select SSB PCI-HOST support, if possible |
60 | config B43_PCI_AUTOSELECT | |
61 | bool | |
62 | depends on B43 && SSB_PCIHOST_POSSIBLE | |
63 | select SSB_PCIHOST | |
c7084535 | 64 | select SSB_B43_PCI_BRIDGE |
e4d6b795 MB |
65 | default y |
66 | ||
67 | # Auto-select SSB PCICORE driver, if possible | |
68 | config B43_PCICORE_AUTOSELECT | |
69 | bool | |
70 | depends on B43 && SSB_DRIVER_PCICORE_POSSIBLE | |
71 | select SSB_DRIVER_PCICORE | |
72 | default y | |
73 | ||
3dbba8e2 | 74 | config B43_SDIO |
afd19ef0 | 75 | bool "Broadcom 43xx SDIO device support" |
1db10595 | 76 | depends on B43 && B43_SSB && SSB_SDIOHOST_POSSIBLE |
3dbba8e2 AH |
77 | select SSB_SDIOHOST |
78 | ---help--- | |
79 | Broadcom 43xx device support for Soft-MAC SDIO devices. | |
80 | ||
81 | With this config option you can drive Soft-MAC b43 cards with a | |
82 | Secure Digital I/O interface. | |
83 | This includes the WLAN daughter card found on the Nintendo Wii | |
84 | video game console. | |
85 | Note that this does not support Broadcom 43xx Full-MAC devices. | |
86 | ||
87 | It's safe to select Y here, even if you don't have a B43 SDIO device. | |
88 | ||
89 | If unsure, say N. | |
90 | ||
9e3bd919 LT |
91 | #Data transfers to the device via PIO. We want it as a fallback even |
92 | # if we can do DMA. | |
8c8b964c RM |
93 | config B43_BCMA_PIO |
94 | bool | |
cc1ad9d2 | 95 | depends on B43 && B43_BCMA |
8c8b964c RM |
96 | select BCMA_BLOCKIO |
97 | default y | |
98 | ||
9e3bd919 LT |
99 | config B43_PIO |
100 | bool | |
fbe057d8 | 101 | depends on B43 && B43_SSB |
9e3bd919 LT |
102 | select SSB_BLOCKIO |
103 | default y | |
104 | ||
418378fe RM |
105 | config B43_PHY_G |
106 | bool "Support for G-PHY (802.11g) devices" | |
107 | depends on B43 && B43_SSB | |
108 | default y | |
109 | ---help--- | |
110 | This PHY type can be found in the following chipsets: | |
111 | PCI: BCM4306, BCM4311, BCM4318 | |
112 | SoC: BCM4712, BCM5352E | |
113 | ||
692d2c0f | 114 | config B43_PHY_N |
ed7f75b4 | 115 | bool "Support for N-PHY (the main 802.11n series) devices" |
afd19ef0 | 116 | depends on B43 |
6b692f3b | 117 | default y |
d5c71e46 | 118 | ---help--- |
ed7f75b4 RM |
119 | This PHY type can be found in the following chipsets: |
120 | PCI: BCM4321, BCM4322, | |
121 | BCM43222, BCM43224, BCM43225, | |
122 | BCM43131, BCM43217, BCM43227, BCM43228 | |
123 | SoC: BCM4716, BCM4717, BCM4718, BCM5356, BCM5357, BCM5358 | |
d5c71e46 | 124 | |
e63e4363 | 125 | config B43_PHY_LP |
ed7f75b4 | 126 | bool "Support for LP-PHY (low-power 802.11g) devices" |
bd7c8a59 | 127 | depends on B43 && B43_SSB |
867b2efe | 128 | default y |
e63e4363 | 129 | ---help--- |
86b2892a | 130 | The LP-PHY is a low-power PHY built into some notebooks |
53dd4b93 | 131 | and embedded devices. It supports 802.11a/b/g |
86b2892a | 132 | (802.11a support is optional, and currently disabled). |
e63e4363 | 133 | |
d7520b1d | 134 | config B43_PHY_HT |
ed7f75b4 | 135 | bool "Support for HT-PHY (high throughput 802.11n) devices" |
7c2332b8 | 136 | depends on B43 && B43_BCMA |
6b692f3b | 137 | default y |
d7520b1d | 138 | ---help--- |
ed7f75b4 | 139 | This PHY type with 3x3:3 MIMO can be found in the BCM4331 PCI chipset. |
d7520b1d | 140 | |
1d738e64 RM |
141 | config B43_PHY_LCN |
142 | bool "Support for LCN-PHY devices (BROKEN)" | |
143 | depends on B43 && BROKEN | |
144 | ---help--- | |
145 | Support for the LCN-PHY. | |
146 | ||
147 | Say N, this is BROKEN and crashes driver. | |
148 | ||
3f7bb3f3 RM |
149 | config B43_PHY_AC |
150 | bool "Support for AC-PHY (802.11ac) devices (BROKEN)" | |
151 | depends on B43 && B43_BCMA && BROKEN | |
152 | ---help--- | |
153 | This PHY type can be found in the following chipsets: | |
154 | PCI: BCM4352, BCM4360 | |
155 | ||
156 | Say N, this is BROKEN and crashes driver. | |
157 | ||
bdb3f751 MB |
158 | # This config option automatically enables b43 LEDS support, |
159 | # if it's possible. | |
21954c36 MB |
160 | config B43_LEDS |
161 | bool | |
bdb3f751 | 162 | depends on B43 && MAC80211_LEDS && (LEDS_CLASS = y || LEDS_CLASS = B43) |
8e9f7529 MB |
163 | default y |
164 | ||
616de35d MB |
165 | # This config option automatically enables b43 HW-RNG support, |
166 | # if the HW-RNG core is enabled. | |
167 | config B43_HWRNG | |
168 | bool | |
169 | depends on B43 && (HW_RANDOM = y || HW_RANDOM = B43) | |
170 | default y | |
171 | ||
e4d6b795 MB |
172 | config B43_DEBUG |
173 | bool "Broadcom 43xx debugging" | |
174 | depends on B43 | |
175 | ---help--- | |
060210f9 | 176 | Broadcom 43xx debugging. |
e4d6b795 | 177 | |
060210f9 | 178 | This adds additional runtime sanity checks and statistics to the driver. |
a8291484 TK |
179 | These checks and statistics might be expensive and hurt the runtime |
180 | performance of your system. | |
060210f9 MB |
181 | This also adds the b43 debugfs interface. |
182 | ||
183 | Do not enable this, unless you are debugging the driver. | |
184 | ||
185 | Say N, if you are a distributor or user building a release kernel | |
186 | for production use. | |
187 | Only say Y, if you are debugging a problem in the b43 driver sourcecode. |