[linux-2.6-block.git] / drivers / net / Kconfig

#
# Network device configuration
#

menuconfig NETDEVICES
	default y if UML
	depends on NET
	bool "Network device support"
	---help---
	  You can say N here if you don't intend to connect your Linux box to
	  any other computer at all.

	  You'll have to say Y if your computer contains a network card that
	  you want to use under Linux. If you are going to run SLIP or PPP over
	  telephone line or null modem cable you need say Y here. Connecting
	  two machines with parallel ports using PLIP needs this, as well as
	  AX.25/KISS for sending Internet traffic over amateur radio links.

	  See also "The Linux Network Administrator's Guide" by Olaf Kirch and
	  Terry Dawson. Available at <http://www.tldp.org/guides.html>.

	  If unsure, say Y.

# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
if NETDEVICES

config MII
	tristate

config NET_CORE
	default y
	bool "Network core driver support"
	---help---
	  You can say N here if you do not intend to use any of the
	  networking core drivers (i.e. VLAN, bridging, bonding, etc.)

if NET_CORE

config BONDING
	tristate "Bonding driver support"
	depends on INET
	depends on IPV6 || IPV6=n
	---help---
	  Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
	  Channels together. This is called 'Etherchannel' by Cisco,
	  'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.

	  The driver supports multiple bonding modes to allow for both high
	  performance and high availability operation.

	  Refer to <file:Documentation/networking/bonding.txt> for more
	  information.

	  To compile this driver as a module, choose M here: the module
	  will be called bonding.

config DUMMY
	tristate "Dummy net driver support"
	---help---
	  This is essentially a bit-bucket device (i.e. traffic you send to
	  this device is consigned into oblivion) with a configurable IP
	  address. It is most commonly used in order to make your currently
	  inactive SLIP address seem like a real address for local programs.
	  If you use SLIP or PPP, you might want to say Y here. Since this
	  thing often comes in handy, the default is Y. It won't enlarge your
	  kernel either. What a deal. Read about it in the Network
	  Administrator's Guide, available from
	  <http://www.tldp.org/docs.html#guide>.

	  To compile this driver as a module, choose M here: the module
	  will be called dummy.

config EQUALIZER
	tristate "EQL (serial line load balancing) support"
	---help---
	  If you have two serial connections to some other computer (this
	  usually requires two modems and two telephone lines) and you use
	  SLIP (the protocol for sending Internet traffic over telephone
	  lines) or PPP (a better SLIP) on them, you can make them behave like
	  one double speed connection using this driver.  Naturally, this has
	  to be supported at the other end as well, either with a similar EQL
	  Linux driver or with a Livingston Portmaster 2e.

	  Say Y if you want this and read
	  <file:Documentation/networking/eql.txt>.  You may also want to read
	  section 6.2 of the NET-3-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here: the module
	  will be called eql.  If unsure, say N.

config NET_FC
	bool "Fibre Channel driver support"
	depends on SCSI && PCI
	help
	  Fibre Channel is a high speed serial protocol mainly used to connect
	  large storage devices to the computer; it is compatible with and
	  intended to replace SCSI.

	  If you intend to use Fibre Channel, you need to have a Fibre channel
	  adaptor card in your computer; say Y here and to the driver for your
	  adaptor below. You also should have said Y to "SCSI support" and
	  "SCSI generic support".

config IFB
	tristate "Intermediate Functional Block support"
	depends on NET_CLS_ACT
	---help---
	  This is an intermediate driver that allows sharing of
	  resources.
	  To compile this driver as a module, choose M here: the module
	  will be called ifb.  If you want to use more than one ifb
	  device at a time, you need to compile this driver as a module.
	  Instead of 'ifb', the devices will then be called 'ifb0',
	  'ifb1' etc.
	  Look at the iproute2 documentation directory for usage etc

source "drivers/net/team/Kconfig"

config MACVLAN
	tristate "MAC-VLAN support"
	---help---
	  This allows one to create virtual interfaces that map packets to
	  or from specific MAC addresses to a particular interface.

	  Macvlan devices can be added using the "ip" command from the
	  iproute2 package starting with the iproute2-2.6.23 release:

	  "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"

	  To compile this driver as a module, choose M here: the module
	  will be called macvlan.

config MACVTAP
	tristate "MAC-VLAN based tap driver"
	depends on MACVLAN
	depends on INET
	help
	  This adds a specialized tap character device driver that is based
	  on the MAC-VLAN network interface, called macvtap. A macvtap device
	  can be added in the same way as a macvlan device, using 'type
	  macvtap', and then be accessed through the tap user space interface.

	  To compile this driver as a module, choose M here: the module
	  will be called macvtap.

config VXLAN
       tristate "Virtual eXtensible Local Area Network (VXLAN)"
       depends on INET
       select NET_UDP_TUNNEL
       ---help---
	  This allows one to create vxlan virtual interfaces that provide
	  Layer 2 Networks over Layer 3 Networks. VXLAN is often used
	  to tunnel virtual network infrastructure in virtualized environments.
	  For more information see:
	    http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02

	  To compile this driver as a module, choose M here: the module
	  will be called vxlan.

config NETCONSOLE
	tristate "Network console logging support"
	---help---
	If you want to log kernel messages over the network, enable this.
	See <file:Documentation/networking/netconsole.txt> for details.

config NETCONSOLE_DYNAMIC
	bool "Dynamic reconfiguration of logging targets"
	depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
			!(NETCONSOLE=y && CONFIGFS_FS=m)
	help
	  This option enables the ability to dynamically reconfigure target
	  parameters (interface, IP addresses, port numbers, MAC addresses)
	  at runtime through a userspace interface exported using configfs.
	  See <file:Documentation/networking/netconsole.txt> for details.

config NETPOLL
	def_bool NETCONSOLE

config NET_POLL_CONTROLLER
	def_bool NETPOLL

config NTB_NETDEV
	tristate "Virtual Ethernet over NTB"
	depends on NTB

config RIONET
	tristate "RapidIO Ethernet over messaging driver support"
	depends on RAPIDIO

config RIONET_TX_SIZE
	int "Number of outbound queue entries"
	depends on RIONET
	default "128"

config RIONET_RX_SIZE
	int "Number of inbound queue entries"
	depends on RIONET
	default "128"

config TUN
	tristate "Universal TUN/TAP device driver support"
	depends on INET
	select CRC32
	---help---
	  TUN/TAP provides packet reception and transmission for user space
	  programs.  It can be viewed as a simple Point-to-Point or Ethernet
	  device, which instead of receiving packets from a physical media,
	  receives them from user space program and instead of sending packets
	  via physical media writes them to the user space program.

	  When a program opens /dev/net/tun, driver creates and registers
	  corresponding net device tunX or tapX.  After a program closed above
	  devices, driver will automatically delete tunXX or tapXX device and
	  all routes corresponding to it.

	  Please read <file:Documentation/networking/tuntap.txt> for more
	  information.

	  To compile this driver as a module, choose M here: the module
	  will be called tun.

	  If you don't know what to use this for, you don't need it.

config VETH
	tristate "Virtual ethernet pair device"
	---help---
	  This device is a local ethernet tunnel. Devices are created in pairs.
	  When one end receives the packet it appears on its pair and vice
	  versa.

config VIRTIO_NET
	tristate "Virtio network driver"
	depends on VIRTIO
	select AVERAGE
	---help---
	  This is the virtual network driver for virtio.  It can be used with
	  lguest or QEMU based VMMs (like KVM or Xen).  Say Y or M.

config NLMON
	tristate "Virtual netlink monitoring device"
	---help---
	  This option enables a monitoring net device for netlink skbs. The
	  purpose of this is to analyze netlink messages with packet sockets.
	  Thus applications like tcpdump will be able to see local netlink
	  messages if they tap into the netlink device, record pcaps for further
	  diagnostics, etc. This is mostly intended for developers or support
	  to debug netlink issues. If unsure, say N.

endif # NET_CORE

config SUNGEM_PHY
	tristate

source "drivers/net/arcnet/Kconfig"

source "drivers/atm/Kconfig"

source "drivers/net/caif/Kconfig"

source "drivers/net/dsa/Kconfig"

source "drivers/net/ethernet/Kconfig"

source "drivers/net/fddi/Kconfig"

source "drivers/net/hippi/Kconfig"

config NET_SB1000
	tristate "General Instruments Surfboard 1000"
	depends on PNP
	---help---
	  This is a driver for the General Instrument (also known as
	  NextLevel) SURFboard 1000 internal
	  cable modem. This is an ISA card which is used by a number of cable
	  TV companies to provide cable modem access. It's a one-way
	  downstream-only cable modem, meaning that your upstream net link is
	  provided by your regular phone modem.

	  At present this driver only compiles as a module, so say M here if
	  you have this card. The module will be called sb1000. Then read
	  <file:Documentation/networking/README.sb1000> for information on how
	  to use this module, as it needs special ppp scripts for establishing
	  a connection. Further documentation and the necessary scripts can be
	  found at:

	  <http://www.jacksonville.net/~fventuri/>
	  <http://home.adelphia.net/~siglercm/sb1000.html>
	  <http://linuxpower.cx/~cable/>

	  If you don't have this card, of course say N.

source "drivers/net/phy/Kconfig"

source "drivers/net/plip/Kconfig"

source "drivers/net/ppp/Kconfig"

source "drivers/net/slip/Kconfig"

source "drivers/s390/net/Kconfig"

source "drivers/net/usb/Kconfig"

source "drivers/net/wireless/Kconfig"

source "drivers/net/wimax/Kconfig"

source "drivers/net/wan/Kconfig"

source "drivers/net/ieee802154/Kconfig"

config XEN_NETDEV_FRONTEND
	tristate "Xen network device frontend driver"
	depends on XEN
	select XEN_XENBUS_FRONTEND
	default y
	help
	  This driver provides support for Xen paravirtual network
	  devices exported by a Xen network driver domain (often
	  domain 0).

	  The corresponding Linux backend driver is enabled by the
	  CONFIG_XEN_NETDEV_BACKEND option.

	  If you are compiling a kernel for use as Xen guest, you
	  should say Y here. To compile this driver as a module, chose
	  M here: the module will be called xen-netfront.

config XEN_NETDEV_BACKEND
	tristate "Xen backend network device"
	depends on XEN_BACKEND
	help
	  This driver allows the kernel to act as a Xen network driver
	  domain which exports paravirtual network devices to other
	  Xen domains. These devices can be accessed by any operating
	  system that implements a compatible front end.

	  The corresponding Linux frontend driver is enabled by the
	  CONFIG_XEN_NETDEV_FRONTEND configuration option.

	  The backend driver presents a standard network device
	  endpoint for each paravirtual network device to the driver
	  domain network stack. These can then be bridged or routed
	  etc in order to provide full network connectivity.

	  If you are compiling a kernel to run in a Xen network driver
	  domain (often this is domain 0) you should say Y here. To
	  compile this driver as a module, chose M here: the module
	  will be called xen-netback.

config VMXNET3
	tristate "VMware VMXNET3 ethernet driver"
	depends on PCI && INET
	help
	  This driver supports VMware's vmxnet3 virtual ethernet NIC.
	  To compile this driver as a module, choose M here: the
	  module will be called vmxnet3.

source "drivers/net/hyperv/Kconfig"

endif # NETDEVICES
Commit	Line	Data
1da177e4 LT	1	#
	2	# Network device configuration
	3	#
	4
d1c0a65f	5	menuconfig NETDEVICES
ce2d2aed	6	default y if UML
e0009820	7	depends on NET
1da177e4 LT	8	bool "Network device support"
	9	---help---
	10	You can say N here if you don't intend to connect your Linux box to
	11	any other computer at all.
	12
	13	You'll have to say Y if your computer contains a network card that
	14	you want to use under Linux. If you are going to run SLIP or PPP over
	15	telephone line or null modem cable you need say Y here. Connecting
	16	two machines with parallel ports using PLIP needs this, as well as
	17	AX.25/KISS for sending Internet traffic over amateur radio links.
	18
	19	See also "The Linux Network Administrator's Guide" by Olaf Kirch and
	20	Terry Dawson. Available at <http://www.tldp.org/guides.html>.
	21
	22	If unsure, say Y.
	23
1618cb0c RD	24	# All the following symbols are dependent on NETDEVICES - do not repeat
	25	# that for each of the symbols.
	26	if NETDEVICES
cbcd2a4c	27
a1606c7d BH	28	config MII
	29	tristate
	30
88491d81 JK	31	config NET_CORE
	32	default y
	33	bool "Network core driver support"
253af423	34	---help---
88491d81 JK	35	You can say N here if you do not intend to use any of the
	36	networking core drivers (i.e. VLAN, bridging, bonding, etc.)
	37
	38	if NET_CORE
	39
	40	config BONDING
	41	tristate "Bonding driver support"
	42	depends on INET
	43	depends on IPV6 \|\| IPV6=n
	44	---help---
	45	Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
	46	Channels together. This is called 'Etherchannel' by Cisco,
	47	'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
	48
	49	The driver supports multiple bonding modes to allow for both high
	50	performance and high availability operation.
	51
	52	Refer to <file:Documentation/networking/bonding.txt> for more
	53	information.
	54
253af423	55	To compile this driver as a module, choose M here: the module
88491d81	56	will be called bonding.
253af423	57
1da177e4 LT	58	config DUMMY
1da177e4 LT	59	tristate "Dummy net driver support"
1da177e4 LT	60	---help---
	61	This is essentially a bit-bucket device (i.e. traffic you send to
	62	this device is consigned into oblivion) with a configurable IP
	63	address. It is most commonly used in order to make your currently
	64	inactive SLIP address seem like a real address for local programs.
	65	If you use SLIP or PPP, you might want to say Y here. Since this
	66	thing often comes in handy, the default is Y. It won't enlarge your
	67	kernel either. What a deal. Read about it in the Network
	68	Administrator's Guide, available from
	69	<http://www.tldp.org/docs.html#guide>.
	70
	71	To compile this driver as a module, choose M here: the module
9f486619	72	will be called dummy.
1da177e4	73
88491d81 JK	74	config EQUALIZER
88491d81 JK	75	tristate "EQL (serial line load balancing) support"
1da177e4	76	---help---
88491d81 JK	77	If you have two serial connections to some other computer (this
	78	usually requires two modems and two telephone lines) and you use
	79	SLIP (the protocol for sending Internet traffic over telephone
	80	lines) or PPP (a better SLIP) on them, you can make them behave like
	81	one double speed connection using this driver. Naturally, this has
	82	to be supported at the other end as well, either with a similar EQL
	83	Linux driver or with a Livingston Portmaster 2e.
1da177e4	84
88491d81 JK	85	Say Y if you want this and read
	86	<file:Documentation/networking/eql.txt>. You may also want to read
	87	section 6.2 of the NET-3-HOWTO, available from
	88	<http://www.tldp.org/docs.html#howto>.
1da177e4	89
88491d81 JK	90	To compile this driver as a module, choose M here: the module
	91	will be called eql. If unsure, say N.
	92
	93	config NET_FC
	94	bool "Fibre Channel driver support"
	95	depends on SCSI && PCI
	96	help
	97	Fibre Channel is a high speed serial protocol mainly used to connect
	98	large storage devices to the computer; it is compatible with and
	99	intended to replace SCSI.
	100
	101	If you intend to use Fibre Channel, you need to have a Fibre channel
	102	adaptor card in your computer; say Y here and to the driver for your
	103	adaptor below. You also should have said Y to "SCSI support" and
	104	"SCSI generic support".
1da177e4	105
88491d81 JK	106	config IFB
	107	tristate "Intermediate Functional Block support"
	108	depends on NET_CLS_ACT
	109	---help---
	110	This is an intermediate driver that allows sharing of
	111	resources.
1da177e4	112	To compile this driver as a module, choose M here: the module
88491d81 JK	113	will be called ifb. If you want to use more than one ifb
	114	device at a time, you need to compile this driver as a module.
	115	Instead of 'ifb', the devices will then be called 'ifb0',
	116	'ifb1' etc.
	117	Look at the iproute2 documentation directory for usage etc
1da177e4	118
3d249d4c JP	119	source "drivers/net/team/Kconfig"
3d249d4c JP	120
b863ceb7	121	config MACVLAN
bd085b93	122	tristate "MAC-VLAN support"
b863ceb7 PM	123	---help---
	124	This allows one to create virtual interfaces that map packets to
	125	or from specific MAC addresses to a particular interface.
	126
3dbf8d56 PM	127	Macvlan devices can be added using the "ip" command from the
	128	iproute2 package starting with the iproute2-2.6.23 release:
	129
	130	"ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
	131
b863ceb7 PM	132	To compile this driver as a module, choose M here: the module
	133	will be called macvlan.
	134
20d29d7a	135	config MACVTAP
bd085b93	136	tristate "MAC-VLAN based tap driver"
20d29d7a	137	depends on MACVLAN
de11b0e8	138	depends on INET
20d29d7a AB	139	help
	140	This adds a specialized tap character device driver that is based
	141	on the MAC-VLAN network interface, called macvtap. A macvtap device
	142	can be added in the same way as a macvlan device, using 'type
c7966b52	143	macvtap', and then be accessed through the tap user space interface.
20d29d7a AB	144
	145	To compile this driver as a module, choose M here: the module
	146	will be called macvtap.
	147
d342894c	148	config VXLAN
d342894c	149	tristate "Virtual eXtensible Local Area Network (VXLAN)"
c9b20a5e	150	depends on INET
3ee64f39	151	select NET_UDP_TUNNEL
d342894c	152	---help---
	153	This allows one to create vxlan virtual interfaces that provide
	154	Layer 2 Networks over Layer 3 Networks. VXLAN is often used
	155	to tunnel virtual network infrastructure in virtualized environments.
	156	For more information see:
	157	http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02
	158
	159	To compile this driver as a module, choose M here: the module
	160	will be called vxlan.
	161
88491d81 JK	162	config NETCONSOLE
88491d81 JK	163	tristate "Network console logging support"
1da177e4	164	---help---
88491d81 JK	165	If you want to log kernel messages over the network, enable this.
88491d81 JK	166	See <file:Documentation/networking/netconsole.txt> for details.
1da177e4	167
88491d81 JK	168	config NETCONSOLE_DYNAMIC
	169	bool "Dynamic reconfiguration of logging targets"
	170	depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
	171	!(NETCONSOLE=y && CONFIGFS_FS=m)
	172	help
	173	This option enables the ability to dynamically reconfigure target
	174	parameters (interface, IP addresses, port numbers, MAC addresses)
	175	at runtime through a userspace interface exported using configfs.
	176	See <file:Documentation/networking/netconsole.txt> for details.
1da177e4	177
88491d81 JK	178	config NETPOLL
	179	def_bool NETCONSOLE
	180
88491d81 JK	181	config NET_POLL_CONTROLLER
	182	def_bool NETPOLL
	183
548c237c JM	184	config NTB_NETDEV
	185	tristate "Virtual Ethernet over NTB"
	186	depends on NTB
	187
88491d81 JK	188	config RIONET
	189	tristate "RapidIO Ethernet over messaging driver support"
	190	depends on RAPIDIO
	191
	192	config RIONET_TX_SIZE
	193	int "Number of outbound queue entries"
	194	depends on RIONET
	195	default "128"
	196
	197	config RIONET_RX_SIZE
	198	int "Number of inbound queue entries"
	199	depends on RIONET
	200	default "128"
1da177e4 LT	201
	202	config TUN
	203	tristate "Universal TUN/TAP device driver support"
de11b0e8	204	depends on INET
1da177e4 LT	205	select CRC32
	206	---help---
	207	TUN/TAP provides packet reception and transmission for user space
	208	programs. It can be viewed as a simple Point-to-Point or Ethernet
	209	device, which instead of receiving packets from a physical media,
	210	receives them from user space program and instead of sending packets
	211	via physical media writes them to the user space program.
	212
	213	When a program opens /dev/net/tun, driver creates and registers
	214	corresponding net device tunX or tapX. After a program closed above
	215	devices, driver will automatically delete tunXX or tapXX device and
	216	all routes corresponding to it.
	217
	218	Please read <file:Documentation/networking/tuntap.txt> for more
	219	information.
	220
	221	To compile this driver as a module, choose M here: the module
	222	will be called tun.
	223
	224	If you don't know what to use this for, you don't need it.
	225
e314dbdc	226	config VETH
6a9a0250	227	tristate "Virtual ethernet pair device"
e314dbdc	228	---help---
6a9a0250 RR	229	This device is a local ethernet tunnel. Devices are created in pairs.
	230	When one end receives the packet it appears on its pair and vice
	231	versa.
e314dbdc	232
88491d81	233	config VIRTIO_NET
bd085b93 KC	234	tristate "Virtio network driver"
bd085b93 KC	235	depends on VIRTIO
8cabd6a0	236	select AVERAGE
88491d81 JK	237	---help---
	238	This is the virtual network driver for virtio. It can be used with
	239	lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
	240
e4fc408e DB	241	config NLMON
	242	tristate "Virtual netlink monitoring device"
	243	---help---
	244	This option enables a monitoring net device for netlink skbs. The
	245	purpose of this is to analyze netlink messages with packet sockets.
	246	Thus applications like tcpdump will be able to see local netlink
	247	messages if they tap into the netlink device, record pcaps for further
	248	diagnostics, etc. This is mostly intended for developers or support
	249	to debug netlink issues. If unsure, say N.
	250
88491d81 JK	251	endif # NET_CORE
	252
	253	config SUNGEM_PHY
	254	tristate
	255
	256	source "drivers/net/arcnet/Kconfig"
	257
	258	source "drivers/atm/Kconfig"
	259
	260	source "drivers/net/caif/Kconfig"
	261
3b158859 BH	262	source "drivers/net/dsa/Kconfig"
3b158859 BH	263
88491d81 JK	264	source "drivers/net/ethernet/Kconfig"
	265
	266	source "drivers/net/fddi/Kconfig"
	267
fecc7351 PB	268	source "drivers/net/hippi/Kconfig"
fecc7351 PB	269
1da177e4 LT	270	config NET_SB1000
1da177e4 LT	271	tristate "General Instruments Surfboard 1000"
cbcd2a4c	272	depends on PNP
1da177e4 LT	273	---help---
	274	This is a driver for the General Instrument (also known as
	275	NextLevel) SURFboard 1000 internal
	276	cable modem. This is an ISA card which is used by a number of cable
	277	TV companies to provide cable modem access. It's a one-way
	278	downstream-only cable modem, meaning that your upstream net link is
	279	provided by your regular phone modem.
	280
	281	At present this driver only compiles as a module, so say M here if
	282	you have this card. The module will be called sb1000. Then read
	283	<file:Documentation/networking/README.sb1000> for information on how
	284	to use this module, as it needs special ppp scripts for establishing
	285	a connection. Further documentation and the necessary scripts can be
	286	found at:
	287
	288	<http://www.jacksonville.net/~fventuri/>
	289	<http://home.adelphia.net/~siglercm/sb1000.html>
	290	<http://linuxpower.cx/~cable/>
	291
	292	If you don't have this card, of course say N.
	293
00db8189 AF	294	source "drivers/net/phy/Kconfig"
00db8189 AF	295
18e635f4 JK	296	source "drivers/net/plip/Kconfig"
18e635f4 JK	297
88491d81 JK	298	source "drivers/net/ppp/Kconfig"
88491d81 JK	299
b5451d78 JK	300	source "drivers/net/slip/Kconfig"
b5451d78 JK	301
88491d81 JK	302	source "drivers/s390/net/Kconfig"
88491d81 JK	303
88491d81 JK	304	source "drivers/net/usb/Kconfig"
88491d81 JK	305
1da177e4 LT	306	source "drivers/net/wireless/Kconfig"
1da177e4 LT	307
143ee2d5 IPG	308	source "drivers/net/wimax/Kconfig"
143ee2d5 IPG	309
1da177e4 LT	310	source "drivers/net/wan/Kconfig"
1da177e4 LT	311
0739d643	312	source "drivers/net/ieee802154/Kconfig"
0739d643	313
0d160211 JF	314	config XEN_NETDEV_FRONTEND
	315	tristate "Xen network device frontend driver"
	316	depends on XEN
7003087c	317	select XEN_XENBUS_FRONTEND
0d160211 JF	318	default y
0d160211 JF	319	help
f942dc25 IC	320	This driver provides support for Xen paravirtual network
	321	devices exported by a Xen network driver domain (often
	322	domain 0).
	323
	324	The corresponding Linux backend driver is enabled by the
	325	CONFIG_XEN_NETDEV_BACKEND option.
	326
	327	If you are compiling a kernel for use as Xen guest, you
	328	should say Y here. To compile this driver as a module, chose
	329	M here: the module will be called xen-netfront.
	330
	331	config XEN_NETDEV_BACKEND
	332	tristate "Xen backend network device"
	333	depends on XEN_BACKEND
	334	help
	335	This driver allows the kernel to act as a Xen network driver
	336	domain which exports paravirtual network devices to other
	337	Xen domains. These devices can be accessed by any operating
	338	system that implements a compatible front end.
	339
	340	The corresponding Linux frontend driver is enabled by the
	341	CONFIG_XEN_NETDEV_FRONTEND configuration option.
	342
	343	The backend driver presents a standard network device
	344	endpoint for each paravirtual network device to the driver
	345	domain network stack. These can then be bridged or routed
	346	etc in order to provide full network connectivity.
	347
	348	If you are compiling a kernel to run in a Xen network driver
	349	domain (often this is domain 0) you should say Y here. To
	350	compile this driver as a module, chose M here: the module
	351	will be called xen-netback.
0d160211	352
d1a890fa	353	config VMXNET3
e85eb117 PDM	354	tristate "VMware VMXNET3 ethernet driver"
	355	depends on PCI && INET
	356	help
	357	This driver supports VMware's vmxnet3 virtual ethernet NIC.
	358	To compile this driver as a module, choose M here: the
	359	module will be called vmxnet3.
d1a890fa	360
95fa0405 HZ	361	source "drivers/net/hyperv/Kconfig"
95fa0405 HZ	362
d1c0a65f	363	endif # NETDEVICES