[linux-2.6-block.git] / drivers / media / radio / Kconfig

#
# Multimedia Video device configuration
#

menuconfig RADIO_ADAPTERS
	bool "Radio Adapters"
	depends on VIDEO_DEV
	default y
	---help---
	  Say Y here to enable selecting AM/FM radio adapters.

if RADIO_ADAPTERS && VIDEO_DEV

config RADIO_CADET
	tristate "ADS Cadet AM/FM Tuner"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these AM/FM radio cards, and then
	  fill in the port address below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  Further documentation on this driver can be found on the WWW at
	  <http://linux.blackhawke.net/cadet/>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-cadet.

config RADIO_RTRACK
	tristate "AIMSlab RadioTrack (aka RadioReveal) support"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards, and then fill
	  in the port address below.

	  Note that newer AIMSlab RadioTrack cards have a different chipset
	  and are not supported by this driver.  For these cards, use the
	  RadioTrack II driver below.

	  If you have a GemTeks combined (PnP) sound- and radio card you must
	  use this driver as a module and setup the card with isapnptools.
	  You must also pass the module a suitable io parameter, 0x248 has
	  been reported to be used by these cards.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>. More information is
	  contained in the file
	  <file:Documentation/video4linux/radiotrack.txt>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-aimslab.

config RADIO_RTRACK_PORT
	hex "RadioTrack i/o port (0x20f or 0x30f)"
	depends on RADIO_RTRACK=y
	default "20f"
	help
	  Enter either 0x30f or 0x20f here.  The card default is 0x30f, if you
	  haven't changed the jumper setting on the card.

config RADIO_RTRACK2
	tristate "AIMSlab RadioTrack II support"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have this FM radio card, and then fill in the
	  port address below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-rtrack2.

config RADIO_RTRACK2_PORT
	hex "RadioTrack II i/o port (0x20c or 0x30c)"
	depends on RADIO_RTRACK2=y
	default "30c"
	help
	  Enter either 0x30c or 0x20c here.  The card default is 0x30c, if you
	  haven't changed the jumper setting on the card.

config RADIO_AZTECH
	tristate "Aztech/Packard Bell Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards, and then fill
	  in the port address below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-aztech.

config RADIO_AZTECH_PORT
	hex "Aztech/Packard Bell I/O port (0x350 or 0x358)"
	depends on RADIO_AZTECH=y
	default "350"
	help
	  Enter either 0x350 or 0x358 here.  The card default is 0x350, if you
	  haven't changed the setting of jumper JP3 on the card.  Removing the
	  jumper sets the card to 0x358.

config RADIO_GEMTEK
	tristate "GemTek Radio Card support"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have this FM radio card, and then fill in the
	  port address below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-gemtek.

config RADIO_GEMTEK_PORT
	hex "GemTek i/o port (0x20c, 0x30c, 0x24c or 0x34c)"
	depends on RADIO_GEMTEK=y
	default "34c"
	help
	  Enter either 0x20c, 0x30c, 0x24c or 0x34c here. The card default is
	  0x34c, if you haven't changed the jumper setting on the card. On
	  Sound Vision 16 Gold PnP with FM Radio (ESS1869+FM Gemtek), the I/O
	  port is 0x28c.

config RADIO_GEMTEK_PCI
	tristate "GemTek PCI Radio Card support"
	depends on VIDEO_V4L2 && PCI
	---help---
	  Choose Y here if you have this PCI FM radio card.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video for Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-gemtek-pci.

config RADIO_MAXIRADIO
	tristate "Guillemot MAXI Radio FM 2000 radio"
	depends on VIDEO_V4L2 && PCI
	---help---
	  Choose Y here if you have this radio card.  This card may also be
	  found as Gemtek PCI FM.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-maxiradio.

config RADIO_MAESTRO
	tristate "Maestro on board radio"
	depends on VIDEO_V4L2 && PCI
	---help---
	  Say Y here to directly support the on-board radio tuner on the
	  Maestro 2 or 2E sound card.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-maestro.

config RADIO_SF16FMI
	tristate "SF16FMI Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards.  If you
	  compile the driver into the kernel and your card is not PnP one, you
	  have to add "sf16fm=<io>" to the kernel command line (I/O address is
	  0x284 or 0x384).

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-sf16fmi.

config RADIO_SF16FMR2
	tristate "SF16FMR2 Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found on the WWW at
	  <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-sf16fmr2.

config RADIO_TERRATEC
	tristate "TerraTec ActiveRadio ISA Standalone"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have this FM radio card, and then fill in the
	  port address below. (TODO)

	  Note: This driver is in its early stages.  Right now volume and
	  frequency control and muting works at least for me, but
	  unfortunately I have not found anybody who wants to use this card
	  with Linux.  So if it is this what YOU are trying to do right now,
	  PLEASE DROP ME A NOTE!!  Rolf Offermanns <rolf@offermanns.de>.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-terratec.

config RADIO_TERRATEC_PORT
	hex "Terratec i/o port (normally 0x590)"
	depends on RADIO_TERRATEC=y
	default "590"
	help
	  Fill in the I/O port of your TerraTec FM radio card. If unsure, go
	  with the default.

config RADIO_TRUST
	tristate "Trust FM radio card"
	depends on ISA && VIDEO_V4L2
	help
	  This is a driver for the Trust FM radio cards. Say Y if you have
	  such a card and want to use it under Linux.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-trust.

config RADIO_TRUST_PORT
	hex "Trust i/o port (usually 0x350 or 0x358)"
	depends on RADIO_TRUST=y
	default "350"
	help
	  Enter the I/O port of your Trust FM radio card. If unsure, try the
	  values "0x350" or "0x358".

config RADIO_TYPHOON
	tristate "Typhoon Radio (a.k.a. EcoRadio)"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards, and then fill
	  in the port address and the frequency used for muting below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-typhoon.

config RADIO_TYPHOON_PROC_FS
	bool "Support for /proc/radio-typhoon"
	depends on PROC_FS && RADIO_TYPHOON
	help
	  Say Y here if you want the typhoon radio card driver to write
	  status information (frequency, volume, muted, mute frequency,
	  base address) to /proc/radio-typhoon. The file can be viewed with
	  your favorite pager (i.e. use "more /proc/radio-typhoon" or "less
	  /proc/radio-typhoon" or simply "cat /proc/radio-typhoon").

config RADIO_TYPHOON_PORT
	hex "Typhoon I/O port (0x316 or 0x336)"
	depends on RADIO_TYPHOON=y
	default "316"
	help
	  Enter the I/O port of your Typhoon or EcoRadio radio card.

config RADIO_TYPHOON_MUTEFREQ
	int "Typhoon frequency set when muting the device (kHz)"
	depends on RADIO_TYPHOON=y
	default "87500"
	help
	  Enter the frequency used for muting the radio. The device is never
	  completely silent. If the volume is just turned down, you can still
	  hear silent voices and music. For that reason, the frequency of the
	  radio device is set to the frequency you can enter here whenever
	  the device is muted. There should be no local radio station at that
	  frequency.

config RADIO_ZOLTRIX
	tristate "Zoltrix Radio"
	depends on ISA && VIDEO_V4L2
	---help---
	  Choose Y here if you have one of these FM radio cards, and then fill
	  in the port address below.

	  In order to control your radio card, you will need to use programs
	  that are compatible with the Video For Linux API.  Information on
	  this API and pointers to "v4l" programs may be found at
	  <file:Documentation/video4linux/API.html>.

	  To compile this driver as a module, choose M here: the
	  module will be called radio-zoltrix.

config RADIO_ZOLTRIX_PORT
	hex "ZOLTRIX I/O port (0x20c or 0x30c)"
	depends on RADIO_ZOLTRIX=y
	default "20c"
	help
	  Enter the I/O port of your Zoltrix radio card.

config USB_DSBR
	tristate "D-Link/GemTek USB FM radio support"
	depends on USB && VIDEO_V4L2
	---help---
	  Say Y here if you want to connect this type of radio to your
	  computer's USB port. Note that the audio is not digital, and
	  you must connect the line out connector to a sound card or a
	  set of speakers.

	  To compile this driver as a module, choose M here: the
	  module will be called dsbr100.

endif # RADIO_ADAPTERS
Commit	Line	Data
1da177e4 LT	1	#
	2	# Multimedia Video device configuration
	3	#
	4
c5da5afb JE	5	menuconfig RADIO_ADAPTERS
c5da5afb JE	6	bool "Radio Adapters"
b10fece5	7	depends on VIDEO_DEV
c5da5afb	8	default y
ff01652c MCC	9	---help---
ff01652c MCC	10	Say Y here to enable selecting AM/FM radio adapters.
c5da5afb	11
59faba1b	12	if RADIO_ADAPTERS && VIDEO_DEV
1da177e4 LT	13
	14	config RADIO_CADET
	15	tristate "ADS Cadet AM/FM Tuner"
c0c7fa09	16	depends on ISA && VIDEO_V4L2
1da177e4 LT	17	---help---
	18	Choose Y here if you have one of these AM/FM radio cards, and then
	19	fill in the port address below.
	20
	21	In order to control your radio card, you will need to use programs
	22	that are compatible with the Video For Linux API. Information on
	23	this API and pointers to "v4l" programs may be found at
	24	<file:Documentation/video4linux/API.html>.
	25
	26	Further documentation on this driver can be found on the WWW at
	27	<http://linux.blackhawke.net/cadet/>.
	28
	29	To compile this driver as a module, choose M here: the
	30	module will be called radio-cadet.
	31
	32	config RADIO_RTRACK
	33	tristate "AIMSlab RadioTrack (aka RadioReveal) support"
46ff2c72	34	depends on ISA && VIDEO_V4L2
1da177e4 LT	35	---help---
	36	Choose Y here if you have one of these FM radio cards, and then fill
	37	in the port address below.
	38
	39	Note that newer AIMSlab RadioTrack cards have a different chipset
	40	and are not supported by this driver. For these cards, use the
	41	RadioTrack II driver below.
	42
	43	If you have a GemTeks combined (PnP) sound- and radio card you must
	44	use this driver as a module and setup the card with isapnptools.
	45	You must also pass the module a suitable io parameter, 0x248 has
	46	been reported to be used by these cards.
	47
	48	In order to control your radio card, you will need to use programs
	49	that are compatible with the Video For Linux API. Information on
	50	this API and pointers to "v4l" programs may be found at
	51	<file:Documentation/video4linux/API.html>. More information is
	52	contained in the file
	53	<file:Documentation/video4linux/radiotrack.txt>.
	54
	55	To compile this driver as a module, choose M here: the
	56	module will be called radio-aimslab.
	57
	58	config RADIO_RTRACK_PORT
	59	hex "RadioTrack i/o port (0x20f or 0x30f)"
	60	depends on RADIO_RTRACK=y
	61	default "20f"
	62	help
	63	Enter either 0x30f or 0x20f here. The card default is 0x30f, if you
	64	haven't changed the jumper setting on the card.
	65
	66	config RADIO_RTRACK2
	67	tristate "AIMSlab RadioTrack II support"
f8c559f8	68	depends on ISA && VIDEO_V4L2
1da177e4 LT	69	---help---
	70	Choose Y here if you have this FM radio card, and then fill in the
	71	port address below.
	72
	73	In order to control your radio card, you will need to use programs
	74	that are compatible with the Video For Linux API. Information on
	75	this API and pointers to "v4l" programs may be found at
	76	<file:Documentation/video4linux/API.html>.
	77
	78	To compile this driver as a module, choose M here: the
	79	module will be called radio-rtrack2.
	80
	81	config RADIO_RTRACK2_PORT
	82	hex "RadioTrack II i/o port (0x20c or 0x30c)"
	83	depends on RADIO_RTRACK2=y
	84	default "30c"
	85	help
	86	Enter either 0x30c or 0x20c here. The card default is 0x30c, if you
	87	haven't changed the jumper setting on the card.
	88
	89	config RADIO_AZTECH
	90	tristate "Aztech/Packard Bell Radio"
a4366af4	91	depends on ISA && VIDEO_V4L2
1da177e4 LT	92	---help---
	93	Choose Y here if you have one of these FM radio cards, and then fill
	94	in the port address below.
	95
	96	In order to control your radio card, you will need to use programs
	97	that are compatible with the Video For Linux API. Information on
	98	this API and pointers to "v4l" programs may be found at
	99	<file:Documentation/video4linux/API.html>.
	100
	101	To compile this driver as a module, choose M here: the
	102	module will be called radio-aztech.
	103
	104	config RADIO_AZTECH_PORT
	105	hex "Aztech/Packard Bell I/O port (0x350 or 0x358)"
	106	depends on RADIO_AZTECH=y
	107	default "350"
	108	help
	109	Enter either 0x350 or 0x358 here. The card default is 0x350, if you
	110	haven't changed the setting of jumper JP3 on the card. Removing the
	111	jumper sets the card to 0x358.
	112
	113	config RADIO_GEMTEK
	114	tristate "GemTek Radio Card support"
d1c4ecde	115	depends on ISA && VIDEO_V4L2
1da177e4 LT	116	---help---
	117	Choose Y here if you have this FM radio card, and then fill in the
	118	port address below.
	119
	120	In order to control your radio card, you will need to use programs
	121	that are compatible with the Video For Linux API. Information on
	122	this API and pointers to "v4l" programs may be found at
	123	<file:Documentation/video4linux/API.html>.
	124
	125	To compile this driver as a module, choose M here: the
	126	module will be called radio-gemtek.
	127
	128	config RADIO_GEMTEK_PORT
	129	hex "GemTek i/o port (0x20c, 0x30c, 0x24c or 0x34c)"
	130	depends on RADIO_GEMTEK=y
	131	default "34c"
	132	help
	133	Enter either 0x20c, 0x30c, 0x24c or 0x34c here. The card default is
	134	0x34c, if you haven't changed the jumper setting on the card. On
	135	Sound Vision 16 Gold PnP with FM Radio (ESS1869+FM Gemtek), the I/O
	136	port is 0x28c.
	137
	138	config RADIO_GEMTEK_PCI
	139	tristate "GemTek PCI Radio Card support"
52afbc2f	140	depends on VIDEO_V4L2 && PCI
1da177e4 LT	141	---help---
	142	Choose Y here if you have this PCI FM radio card.
	143
	144	In order to control your radio card, you will need to use programs
4286c6f6	145	that are compatible with the Video for Linux API. Information on
1da177e4 LT	146	this API and pointers to "v4l" programs may be found at
	147	<file:Documentation/video4linux/API.html>.
	148
	149	To compile this driver as a module, choose M here: the
	150	module will be called radio-gemtek-pci.
	151
	152	config RADIO_MAXIRADIO
	153	tristate "Guillemot MAXI Radio FM 2000 radio"
e84fef6b	154	depends on VIDEO_V4L2 && PCI
1da177e4 LT	155	---help---
	156	Choose Y here if you have this radio card. This card may also be
	157	found as Gemtek PCI FM.
	158
	159	In order to control your radio card, you will need to use programs
	160	that are compatible with the Video For Linux API. Information on
	161	this API and pointers to "v4l" programs may be found at
	162	<file:Documentation/video4linux/API.html>.
	163
	164	To compile this driver as a module, choose M here: the
	165	module will be called radio-maxiradio.
	166
	167	config RADIO_MAESTRO
	168	tristate "Maestro on board radio"
b6055d7b	169	depends on VIDEO_V4L2 && PCI
1da177e4 LT	170	---help---
	171	Say Y here to directly support the on-board radio tuner on the
	172	Maestro 2 or 2E sound card.
	173
	174	In order to control your radio card, you will need to use programs
	175	that are compatible with the Video For Linux API. Information on
	176	this API and pointers to "v4l" programs may be found at
	177	<file:Documentation/video4linux/API.html>.
	178
	179	To compile this driver as a module, choose M here: the
	180	module will be called radio-maestro.
	181
1da177e4 LT	182	config RADIO_SF16FMI
1da177e4 LT	183	tristate "SF16FMI Radio"
a2ef73af	184	depends on ISA && VIDEO_V4L2
1da177e4 LT	185	---help---
	186	Choose Y here if you have one of these FM radio cards. If you
	187	compile the driver into the kernel and your card is not PnP one, you
	188	have to add "sf16fm=<io>" to the kernel command line (I/O address is
	189	0x284 or 0x384).
	190
	191	In order to control your radio card, you will need to use programs
	192	that are compatible with the Video For Linux API. Information on
	193	this API and pointers to "v4l" programs may be found at
	194	<file:Documentation/video4linux/API.html>.
	195
	196	To compile this driver as a module, choose M here: the
	197	module will be called radio-sf16fmi.
	198
	199	config RADIO_SF16FMR2
	200	tristate "SF16FMR2 Radio"
acda0e71	201	depends on ISA && VIDEO_V4L2
1da177e4 LT	202	---help---
	203	Choose Y here if you have one of these FM radio cards.
	204
	205	In order to control your radio card, you will need to use programs
	206	that are compatible with the Video For Linux API. Information on
	207	this API and pointers to "v4l" programs may be found on the WWW at
	208	<http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
	209
	210	To compile this driver as a module, choose M here: the
	211	module will be called radio-sf16fmr2.
	212
	213	config RADIO_TERRATEC
	214	tristate "TerraTec ActiveRadio ISA Standalone"
55ac7b69	215	depends on ISA && VIDEO_V4L2
1da177e4 LT	216	---help---
	217	Choose Y here if you have this FM radio card, and then fill in the
	218	port address below. (TODO)
	219
	220	Note: This driver is in its early stages. Right now volume and
	221	frequency control and muting works at least for me, but
	222	unfortunately I have not found anybody who wants to use this card
	223	with Linux. So if it is this what YOU are trying to do right now,
	224	PLEASE DROP ME A NOTE!! Rolf Offermanns <rolf@offermanns.de>.
	225
	226	In order to control your radio card, you will need to use programs
	227	that are compatible with the Video For Linux API. Information on
	228	this API and pointers to "v4l" programs may be found at
	229	<file:Documentation/video4linux/API.html>.
	230
	231	To compile this driver as a module, choose M here: the
	232	module will be called radio-terratec.
	233
	234	config RADIO_TERRATEC_PORT
	235	hex "Terratec i/o port (normally 0x590)"
	236	depends on RADIO_TERRATEC=y
	237	default "590"
	238	help
	239	Fill in the I/O port of your TerraTec FM radio card. If unsure, go
	240	with the default.
	241
	242	config RADIO_TRUST
	243	tristate "Trust FM radio card"
982eddb9	244	depends on ISA && VIDEO_V4L2
1da177e4 LT	245	help
	246	This is a driver for the Trust FM radio cards. Say Y if you have
	247	such a card and want to use it under Linux.
	248
	249	To compile this driver as a module, choose M here: the
	250	module will be called radio-trust.
	251
	252	config RADIO_TRUST_PORT
	253	hex "Trust i/o port (usually 0x350 or 0x358)"
	254	depends on RADIO_TRUST=y
	255	default "350"
	256	help
	257	Enter the I/O port of your Trust FM radio card. If unsure, try the
	258	values "0x350" or "0x358".
	259
	260	config RADIO_TYPHOON
	261	tristate "Typhoon Radio (a.k.a. EcoRadio)"
30c48305	262	depends on ISA && VIDEO_V4L2
1da177e4 LT	263	---help---
	264	Choose Y here if you have one of these FM radio cards, and then fill
	265	in the port address and the frequency used for muting below.
	266
	267	In order to control your radio card, you will need to use programs
	268	that are compatible with the Video For Linux API. Information on
	269	this API and pointers to "v4l" programs may be found at
	270	<file:Documentation/video4linux/API.html>.
	271
	272	To compile this driver as a module, choose M here: the
	273	module will be called radio-typhoon.
	274
	275	config RADIO_TYPHOON_PROC_FS
	276	bool "Support for /proc/radio-typhoon"
	277	depends on PROC_FS && RADIO_TYPHOON
	278	help
	279	Say Y here if you want the typhoon radio card driver to write
	280	status information (frequency, volume, muted, mute frequency,
	281	base address) to /proc/radio-typhoon. The file can be viewed with
	282	your favorite pager (i.e. use "more /proc/radio-typhoon" or "less
	283	/proc/radio-typhoon" or simply "cat /proc/radio-typhoon").
	284
	285	config RADIO_TYPHOON_PORT
	286	hex "Typhoon I/O port (0x316 or 0x336)"
	287	depends on RADIO_TYPHOON=y
	288	default "316"
	289	help
	290	Enter the I/O port of your Typhoon or EcoRadio radio card.
	291
	292	config RADIO_TYPHOON_MUTEFREQ
	293	int "Typhoon frequency set when muting the device (kHz)"
	294	depends on RADIO_TYPHOON=y
	295	default "87500"
	296	help
	297	Enter the frequency used for muting the radio. The device is never
	298	completely silent. If the volume is just turned down, you can still
	299	hear silent voices and music. For that reason, the frequency of the
	300	radio device is set to the frequency you can enter here whenever
	301	the device is muted. There should be no local radio station at that
	302	frequency.
	303
	304	config RADIO_ZOLTRIX
	305	tristate "Zoltrix Radio"
2ab65299	306	depends on ISA && VIDEO_V4L2
1da177e4 LT	307	---help---
	308	Choose Y here if you have one of these FM radio cards, and then fill
	309	in the port address below.
	310
	311	In order to control your radio card, you will need to use programs
	312	that are compatible with the Video For Linux API. Information on
	313	this API and pointers to "v4l" programs may be found at
	314	<file:Documentation/video4linux/API.html>.
	315
	316	To compile this driver as a module, choose M here: the
	317	module will be called radio-zoltrix.
	318
	319	config RADIO_ZOLTRIX_PORT
	320	hex "ZOLTRIX I/O port (0x20c or 0x30c)"
	321	depends on RADIO_ZOLTRIX=y
	322	default "20c"
	323	help
	324	Enter the I/O port of your Zoltrix radio card.
	325
7fb65297	326	config USB_DSBR
b31c33bd DSL	327	tristate "D-Link/GemTek USB FM radio support"
b31c33bd DSL	328	depends on USB && VIDEO_V4L2
7fb65297 MCC	329	---help---
	330	Say Y here if you want to connect this type of radio to your
	331	computer's USB port. Note that the audio is not digital, and
	332	you must connect the line out connector to a sound card or a
	333	set of speakers.
1da177e4	334
7fb65297 MCC	335	To compile this driver as a module, choose M here: the
7fb65297 MCC	336	module will be called dsbr100.
c5da5afb JE	337
c5da5afb JE	338	endif # RADIO_ADAPTERS