Commit | Line | Data |
---|---|---|
36edc939 | 1 | // SPDX-License-Identifier: GPL-2.0-only |
f46e9203 NC |
2 | /* |
3 | * Copyright 2007-2008 Extreme Engineering Solutions, Inc. | |
4 | * | |
5 | * Author: Nate Case <ncase@xes-inc.com> | |
6 | * | |
f46e9203 NC |
7 | * LED driver for various PCA955x I2C LED drivers |
8 | * | |
9 | * Supported devices: | |
10 | * | |
11 | * Device Description 7-bit slave address | |
12 | * ------ ----------- ------------------- | |
13 | * PCA9550 2-bit driver 0x60 .. 0x61 | |
14 | * PCA9551 8-bit driver 0x60 .. 0x67 | |
15 | * PCA9552 16-bit driver 0x60 .. 0x67 | |
16 | * PCA9553/01 4-bit driver 0x62 | |
17 | * PCA9553/02 4-bit driver 0x63 | |
18 | * | |
19 | * Philips PCA955x LED driver chips follow a register map as shown below: | |
20 | * | |
21 | * Control Register Description | |
22 | * ---------------- ----------- | |
23 | * 0x0 Input register 0 | |
24 | * .. | |
25 | * NUM_INPUT_REGS - 1 Last Input register X | |
26 | * | |
27 | * NUM_INPUT_REGS Frequency prescaler 0 | |
28 | * NUM_INPUT_REGS + 1 PWM register 0 | |
29 | * NUM_INPUT_REGS + 2 Frequency prescaler 1 | |
30 | * NUM_INPUT_REGS + 3 PWM register 1 | |
31 | * | |
32 | * NUM_INPUT_REGS + 4 LED selector 0 | |
33 | * NUM_INPUT_REGS + 4 | |
34 | * + NUM_LED_REGS - 1 Last LED selector | |
35 | * | |
36 | * where NUM_INPUT_REGS and NUM_LED_REGS vary depending on how many | |
37 | * bits the chip supports. | |
38 | */ | |
39 | ||
f46e9203 | 40 | #include <linux/ctype.h> |
ed1f4b96 | 41 | #include <linux/delay.h> |
f46e9203 | 42 | #include <linux/err.h> |
0987c7df | 43 | #include <linux/gpio/driver.h> |
f46e9203 | 44 | #include <linux/i2c.h> |
ed1f4b96 CLG |
45 | #include <linux/leds.h> |
46 | #include <linux/module.h> | |
ed1f4b96 | 47 | #include <linux/of.h> |
967f69de | 48 | #include <linux/property.h> |
5a0e3ad6 | 49 | #include <linux/slab.h> |
ed1f4b96 | 50 | #include <linux/string.h> |
f46e9203 | 51 | |
561099a1 CLG |
52 | #include <dt-bindings/leds/leds-pca955x.h> |
53 | ||
f46e9203 NC |
54 | /* LED select registers determine the source that drives LED outputs */ |
55 | #define PCA955X_LS_LED_ON 0x0 /* Output LOW */ | |
56 | #define PCA955X_LS_LED_OFF 0x1 /* Output HI-Z */ | |
57 | #define PCA955X_LS_BLINK0 0x2 /* Blink at PWM0 rate */ | |
58 | #define PCA955X_LS_BLINK1 0x3 /* Blink at PWM1 rate */ | |
59 | ||
52ca7d0f AJ |
60 | #define PCA955X_GPIO_INPUT LED_OFF |
61 | #define PCA955X_GPIO_HIGH LED_OFF | |
62 | #define PCA955X_GPIO_LOW LED_FULL | |
63 | ||
f46e9203 NC |
64 | enum pca955x_type { |
65 | pca9550, | |
66 | pca9551, | |
67 | pca9552, | |
46de3adb | 68 | ibm_pca9552, |
f46e9203 NC |
69 | pca9553, |
70 | }; | |
71 | ||
72 | struct pca955x_chipdef { | |
73 | int bits; | |
74 | u8 slv_addr; /* 7-bit slave address mask */ | |
75 | int slv_addr_shift; /* Number of bits to ignore */ | |
76 | }; | |
77 | ||
78 | static struct pca955x_chipdef pca955x_chipdefs[] = { | |
79 | [pca9550] = { | |
80 | .bits = 2, | |
81 | .slv_addr = /* 110000x */ 0x60, | |
82 | .slv_addr_shift = 1, | |
83 | }, | |
84 | [pca9551] = { | |
85 | .bits = 8, | |
86 | .slv_addr = /* 1100xxx */ 0x60, | |
87 | .slv_addr_shift = 3, | |
88 | }, | |
89 | [pca9552] = { | |
90 | .bits = 16, | |
91 | .slv_addr = /* 1100xxx */ 0x60, | |
92 | .slv_addr_shift = 3, | |
93 | }, | |
46de3adb EJ |
94 | [ibm_pca9552] = { |
95 | .bits = 16, | |
96 | .slv_addr = /* 0110xxx */ 0x30, | |
97 | .slv_addr_shift = 3, | |
98 | }, | |
f46e9203 NC |
99 | [pca9553] = { |
100 | .bits = 4, | |
101 | .slv_addr = /* 110001x */ 0x62, | |
102 | .slv_addr_shift = 1, | |
103 | }, | |
104 | }; | |
105 | ||
106 | static const struct i2c_device_id pca955x_id[] = { | |
107 | { "pca9550", pca9550 }, | |
108 | { "pca9551", pca9551 }, | |
109 | { "pca9552", pca9552 }, | |
46de3adb | 110 | { "ibm-pca9552", ibm_pca9552 }, |
f46e9203 NC |
111 | { "pca9553", pca9553 }, |
112 | { } | |
113 | }; | |
114 | MODULE_DEVICE_TABLE(i2c, pca955x_id); | |
115 | ||
e7e11d8b AS |
116 | struct pca955x { |
117 | struct mutex lock; | |
118 | struct pca955x_led *leds; | |
f46e9203 NC |
119 | struct pca955x_chipdef *chipdef; |
120 | struct i2c_client *client; | |
561099a1 CLG |
121 | #ifdef CONFIG_LEDS_PCA955X_GPIO |
122 | struct gpio_chip gpio; | |
123 | #endif | |
e7e11d8b AS |
124 | }; |
125 | ||
126 | struct pca955x_led { | |
127 | struct pca955x *pca955x; | |
f46e9203 NC |
128 | struct led_classdev led_cdev; |
129 | int led_num; /* 0 .. 15 potentially */ | |
130 | char name[32]; | |
561099a1 | 131 | u32 type; |
ed1f4b96 CLG |
132 | const char *default_trigger; |
133 | }; | |
134 | ||
135 | struct pca955x_platform_data { | |
136 | struct pca955x_led *leds; | |
137 | int num_leds; | |
f46e9203 NC |
138 | }; |
139 | ||
140 | /* 8 bits per input register */ | |
141 | static inline int pca95xx_num_input_regs(int bits) | |
142 | { | |
143 | return (bits + 7) / 8; | |
144 | } | |
145 | ||
146 | /* 4 bits per LED selector register */ | |
147 | static inline int pca95xx_num_led_regs(int bits) | |
148 | { | |
149 | return (bits + 3) / 4; | |
150 | } | |
151 | ||
152 | /* | |
153 | * Return an LED selector register value based on an existing one, with | |
154 | * the appropriate 2-bit state value set for the given LED number (0-3). | |
155 | */ | |
156 | static inline u8 pca955x_ledsel(u8 oldval, int led_num, int state) | |
157 | { | |
158 | return (oldval & (~(0x3 << (led_num << 1)))) | | |
159 | ((state & 0x3) << (led_num << 1)); | |
160 | } | |
161 | ||
162 | /* | |
163 | * Write to frequency prescaler register, used to program the | |
164 | * period of the PWM output. period = (PSCx + 1) / 38 | |
165 | */ | |
1591caf2 | 166 | static int pca955x_write_psc(struct i2c_client *client, int n, u8 val) |
f46e9203 | 167 | { |
e7e11d8b | 168 | struct pca955x *pca955x = i2c_get_clientdata(client); |
2420ae02 | 169 | u8 cmd = pca95xx_num_input_regs(pca955x->chipdef->bits) + (2 * n); |
1591caf2 | 170 | int ret; |
f46e9203 | 171 | |
2420ae02 | 172 | ret = i2c_smbus_write_byte_data(client, cmd, val); |
1591caf2 CLG |
173 | if (ret < 0) |
174 | dev_err(&client->dev, "%s: reg 0x%x, val 0x%x, err %d\n", | |
175 | __func__, n, val, ret); | |
176 | return ret; | |
f46e9203 NC |
177 | } |
178 | ||
179 | /* | |
180 | * Write to PWM register, which determines the duty cycle of the | |
181 | * output. LED is OFF when the count is less than the value of this | |
182 | * register, and ON when it is greater. If PWMx == 0, LED is always OFF. | |
183 | * | |
184 | * Duty cycle is (256 - PWMx) / 256 | |
185 | */ | |
1591caf2 | 186 | static int pca955x_write_pwm(struct i2c_client *client, int n, u8 val) |
f46e9203 | 187 | { |
e7e11d8b | 188 | struct pca955x *pca955x = i2c_get_clientdata(client); |
2420ae02 | 189 | u8 cmd = pca95xx_num_input_regs(pca955x->chipdef->bits) + 1 + (2 * n); |
1591caf2 | 190 | int ret; |
f46e9203 | 191 | |
2420ae02 | 192 | ret = i2c_smbus_write_byte_data(client, cmd, val); |
1591caf2 CLG |
193 | if (ret < 0) |
194 | dev_err(&client->dev, "%s: reg 0x%x, val 0x%x, err %d\n", | |
195 | __func__, n, val, ret); | |
196 | return ret; | |
f46e9203 NC |
197 | } |
198 | ||
199 | /* | |
200 | * Write to LED selector register, which determines the source that | |
201 | * drives the LED output. | |
202 | */ | |
1591caf2 | 203 | static int pca955x_write_ls(struct i2c_client *client, int n, u8 val) |
f46e9203 | 204 | { |
e7e11d8b | 205 | struct pca955x *pca955x = i2c_get_clientdata(client); |
2420ae02 | 206 | u8 cmd = pca95xx_num_input_regs(pca955x->chipdef->bits) + 4 + n; |
1591caf2 | 207 | int ret; |
f46e9203 | 208 | |
2420ae02 | 209 | ret = i2c_smbus_write_byte_data(client, cmd, val); |
1591caf2 CLG |
210 | if (ret < 0) |
211 | dev_err(&client->dev, "%s: reg 0x%x, val 0x%x, err %d\n", | |
212 | __func__, n, val, ret); | |
213 | return ret; | |
f46e9203 NC |
214 | } |
215 | ||
216 | /* | |
217 | * Read the LED selector register, which determines the source that | |
218 | * drives the LED output. | |
219 | */ | |
1591caf2 | 220 | static int pca955x_read_ls(struct i2c_client *client, int n, u8 *val) |
f46e9203 | 221 | { |
e7e11d8b | 222 | struct pca955x *pca955x = i2c_get_clientdata(client); |
2420ae02 | 223 | u8 cmd = pca95xx_num_input_regs(pca955x->chipdef->bits) + 4 + n; |
1591caf2 | 224 | int ret; |
f46e9203 | 225 | |
2420ae02 | 226 | ret = i2c_smbus_read_byte_data(client, cmd); |
1591caf2 CLG |
227 | if (ret < 0) { |
228 | dev_err(&client->dev, "%s: reg 0x%x, err %d\n", | |
229 | __func__, n, ret); | |
230 | return ret; | |
231 | } | |
232 | *val = (u8)ret; | |
233 | return 0; | |
f46e9203 NC |
234 | } |
235 | ||
7086625f EJ |
236 | static int pca955x_read_pwm(struct i2c_client *client, int n, u8 *val) |
237 | { | |
238 | struct pca955x *pca955x = i2c_get_clientdata(client); | |
239 | u8 cmd = pca95xx_num_input_regs(pca955x->chipdef->bits) + 1 + (2 * n); | |
240 | int ret; | |
241 | ||
242 | ret = i2c_smbus_read_byte_data(client, cmd); | |
243 | if (ret < 0) { | |
244 | dev_err(&client->dev, "%s: reg 0x%x, err %d\n", | |
245 | __func__, n, ret); | |
246 | return ret; | |
247 | } | |
248 | *val = (u8)ret; | |
249 | return 0; | |
250 | } | |
251 | ||
252 | static enum led_brightness pca955x_led_get(struct led_classdev *led_cdev) | |
253 | { | |
254 | struct pca955x_led *pca955x_led = container_of(led_cdev, | |
255 | struct pca955x_led, | |
256 | led_cdev); | |
257 | struct pca955x *pca955x = pca955x_led->pca955x; | |
258 | u8 ls, pwm; | |
259 | int ret; | |
260 | ||
261 | ret = pca955x_read_ls(pca955x->client, pca955x_led->led_num / 4, &ls); | |
262 | if (ret) | |
263 | return ret; | |
264 | ||
265 | ls = (ls >> ((pca955x_led->led_num % 4) << 1)) & 0x3; | |
266 | switch (ls) { | |
267 | case PCA955X_LS_LED_ON: | |
268 | ret = LED_FULL; | |
269 | break; | |
270 | case PCA955X_LS_LED_OFF: | |
271 | ret = LED_OFF; | |
272 | break; | |
273 | case PCA955X_LS_BLINK0: | |
274 | ret = LED_HALF; | |
275 | break; | |
276 | case PCA955X_LS_BLINK1: | |
277 | ret = pca955x_read_pwm(pca955x->client, 1, &pwm); | |
278 | if (ret) | |
279 | return ret; | |
280 | ret = 255 - pwm; | |
281 | break; | |
282 | } | |
283 | ||
284 | return ret; | |
285 | } | |
286 | ||
c3482b82 AL |
287 | static int pca955x_led_set(struct led_classdev *led_cdev, |
288 | enum led_brightness value) | |
f46e9203 | 289 | { |
e7e11d8b AS |
290 | struct pca955x_led *pca955x_led; |
291 | struct pca955x *pca955x; | |
f46e9203 NC |
292 | u8 ls; |
293 | int chip_ls; /* which LSx to use (0-3 potentially) */ | |
294 | int ls_led; /* which set of bits within LSx to use (0-3) */ | |
1591caf2 | 295 | int ret; |
f46e9203 | 296 | |
c3482b82 | 297 | pca955x_led = container_of(led_cdev, struct pca955x_led, led_cdev); |
e7e11d8b AS |
298 | pca955x = pca955x_led->pca955x; |
299 | ||
300 | chip_ls = pca955x_led->led_num / 4; | |
301 | ls_led = pca955x_led->led_num % 4; | |
302 | ||
303 | mutex_lock(&pca955x->lock); | |
f46e9203 | 304 | |
1591caf2 CLG |
305 | ret = pca955x_read_ls(pca955x->client, chip_ls, &ls); |
306 | if (ret) | |
307 | goto out; | |
f46e9203 | 308 | |
c3482b82 | 309 | switch (value) { |
f46e9203 NC |
310 | case LED_FULL: |
311 | ls = pca955x_ledsel(ls, ls_led, PCA955X_LS_LED_ON); | |
312 | break; | |
313 | case LED_OFF: | |
314 | ls = pca955x_ledsel(ls, ls_led, PCA955X_LS_LED_OFF); | |
315 | break; | |
316 | case LED_HALF: | |
317 | ls = pca955x_ledsel(ls, ls_led, PCA955X_LS_BLINK0); | |
318 | break; | |
319 | default: | |
320 | /* | |
321 | * Use PWM1 for all other values. This has the unwanted | |
322 | * side effect of making all LEDs on the chip share the | |
323 | * same brightness level if set to a value other than | |
324 | * OFF, HALF, or FULL. But, this is probably better than | |
325 | * just turning off for all other values. | |
326 | */ | |
1591caf2 CLG |
327 | ret = pca955x_write_pwm(pca955x->client, 1, 255 - value); |
328 | if (ret) | |
329 | goto out; | |
f46e9203 NC |
330 | ls = pca955x_ledsel(ls, ls_led, PCA955X_LS_BLINK1); |
331 | break; | |
332 | } | |
333 | ||
1591caf2 | 334 | ret = pca955x_write_ls(pca955x->client, chip_ls, ls); |
e7e11d8b | 335 | |
1591caf2 | 336 | out: |
e7e11d8b | 337 | mutex_unlock(&pca955x->lock); |
f46e9203 | 338 | |
1591caf2 | 339 | return ret; |
f46e9203 NC |
340 | } |
341 | ||
561099a1 CLG |
342 | #ifdef CONFIG_LEDS_PCA955X_GPIO |
343 | /* | |
344 | * Read the INPUT register, which contains the state of LEDs. | |
345 | */ | |
1591caf2 | 346 | static int pca955x_read_input(struct i2c_client *client, int n, u8 *val) |
561099a1 | 347 | { |
1591caf2 CLG |
348 | int ret = i2c_smbus_read_byte_data(client, n); |
349 | ||
350 | if (ret < 0) { | |
351 | dev_err(&client->dev, "%s: reg 0x%x, err %d\n", | |
352 | __func__, n, ret); | |
353 | return ret; | |
354 | } | |
355 | *val = (u8)ret; | |
356 | return 0; | |
357 | ||
561099a1 CLG |
358 | } |
359 | ||
360 | static int pca955x_gpio_request_pin(struct gpio_chip *gc, unsigned int offset) | |
361 | { | |
362 | struct pca955x *pca955x = gpiochip_get_data(gc); | |
363 | struct pca955x_led *led = &pca955x->leds[offset]; | |
364 | ||
365 | if (led->type == PCA955X_TYPE_GPIO) | |
366 | return 0; | |
367 | ||
368 | return -EBUSY; | |
369 | } | |
370 | ||
1591caf2 CLG |
371 | static int pca955x_set_value(struct gpio_chip *gc, unsigned int offset, |
372 | int val) | |
561099a1 CLG |
373 | { |
374 | struct pca955x *pca955x = gpiochip_get_data(gc); | |
375 | struct pca955x_led *led = &pca955x->leds[offset]; | |
376 | ||
377 | if (val) | |
52ca7d0f AJ |
378 | return pca955x_led_set(&led->led_cdev, PCA955X_GPIO_HIGH); |
379 | ||
380 | return pca955x_led_set(&led->led_cdev, PCA955X_GPIO_LOW); | |
1591caf2 CLG |
381 | } |
382 | ||
383 | static void pca955x_gpio_set_value(struct gpio_chip *gc, unsigned int offset, | |
384 | int val) | |
385 | { | |
386 | pca955x_set_value(gc, offset, val); | |
561099a1 CLG |
387 | } |
388 | ||
389 | static int pca955x_gpio_get_value(struct gpio_chip *gc, unsigned int offset) | |
390 | { | |
391 | struct pca955x *pca955x = gpiochip_get_data(gc); | |
392 | struct pca955x_led *led = &pca955x->leds[offset]; | |
1591caf2 CLG |
393 | u8 reg = 0; |
394 | ||
395 | /* There is nothing we can do about errors */ | |
396 | pca955x_read_input(pca955x->client, led->led_num / 8, ®); | |
561099a1 CLG |
397 | |
398 | return !!(reg & (1 << (led->led_num % 8))); | |
399 | } | |
400 | ||
401 | static int pca955x_gpio_direction_input(struct gpio_chip *gc, | |
402 | unsigned int offset) | |
403 | { | |
52ca7d0f AJ |
404 | struct pca955x *pca955x = gpiochip_get_data(gc); |
405 | struct pca955x_led *led = &pca955x->leds[offset]; | |
406 | ||
407 | /* To use as input ensure pin is not driven. */ | |
408 | return pca955x_led_set(&led->led_cdev, PCA955X_GPIO_INPUT); | |
561099a1 CLG |
409 | } |
410 | ||
411 | static int pca955x_gpio_direction_output(struct gpio_chip *gc, | |
412 | unsigned int offset, int val) | |
413 | { | |
1591caf2 | 414 | return pca955x_set_value(gc, offset, val); |
561099a1 CLG |
415 | } |
416 | #endif /* CONFIG_LEDS_PCA955X_GPIO */ | |
417 | ||
ed1f4b96 | 418 | static struct pca955x_platform_data * |
967f69de | 419 | pca955x_get_pdata(struct i2c_client *client, struct pca955x_chipdef *chip) |
ed1f4b96 | 420 | { |
ed1f4b96 | 421 | struct pca955x_platform_data *pdata; |
2420ae02 | 422 | struct pca955x_led *led; |
967f69de | 423 | struct fwnode_handle *child; |
ed1f4b96 CLG |
424 | int count; |
425 | ||
967f69de | 426 | count = device_get_child_node_count(&client->dev); |
ed1f4b96 CLG |
427 | if (!count || count > chip->bits) |
428 | return ERR_PTR(-ENODEV); | |
429 | ||
430 | pdata = devm_kzalloc(&client->dev, sizeof(*pdata), GFP_KERNEL); | |
431 | if (!pdata) | |
432 | return ERR_PTR(-ENOMEM); | |
433 | ||
a86854d0 KC |
434 | pdata->leds = devm_kcalloc(&client->dev, |
435 | chip->bits, sizeof(struct pca955x_led), | |
ed1f4b96 CLG |
436 | GFP_KERNEL); |
437 | if (!pdata->leds) | |
438 | return ERR_PTR(-ENOMEM); | |
439 | ||
967f69de | 440 | device_for_each_child_node(&client->dev, child) { |
ed1f4b96 CLG |
441 | const char *name; |
442 | u32 reg; | |
443 | int res; | |
444 | ||
967f69de | 445 | res = fwnode_property_read_u32(child, "reg", ®); |
ed1f4b96 CLG |
446 | if ((res != 0) || (reg >= chip->bits)) |
447 | continue; | |
448 | ||
967f69de AS |
449 | res = fwnode_property_read_string(child, "label", &name); |
450 | if ((res != 0) && is_of_node(child)) | |
451 | name = to_of_node(child)->name; | |
ed1f4b96 | 452 | |
2420ae02 EJ |
453 | led = &pdata->leds[reg]; |
454 | snprintf(led->name, sizeof(led->name), "%s", name); | |
ed1f4b96 | 455 | |
2420ae02 EJ |
456 | led->type = PCA955X_TYPE_LED; |
457 | fwnode_property_read_u32(child, "type", &led->type); | |
967f69de | 458 | fwnode_property_read_string(child, "linux,default-trigger", |
2420ae02 | 459 | &led->default_trigger); |
ed1f4b96 CLG |
460 | } |
461 | ||
462 | pdata->num_leds = chip->bits; | |
463 | ||
464 | return pdata; | |
465 | } | |
466 | ||
467 | static const struct of_device_id of_pca955x_match[] = { | |
468 | { .compatible = "nxp,pca9550", .data = (void *)pca9550 }, | |
469 | { .compatible = "nxp,pca9551", .data = (void *)pca9551 }, | |
470 | { .compatible = "nxp,pca9552", .data = (void *)pca9552 }, | |
46de3adb | 471 | { .compatible = "ibm,pca9552", .data = (void *)ibm_pca9552 }, |
ed1f4b96 CLG |
472 | { .compatible = "nxp,pca9553", .data = (void *)pca9553 }, |
473 | {}, | |
474 | }; | |
ed1f4b96 | 475 | MODULE_DEVICE_TABLE(of, of_pca955x_match); |
ed1f4b96 | 476 | |
98ea1ea2 | 477 | static int pca955x_probe(struct i2c_client *client, |
2420ae02 | 478 | const struct i2c_device_id *id) |
f46e9203 | 479 | { |
e7e11d8b AS |
480 | struct pca955x *pca955x; |
481 | struct pca955x_led *pca955x_led; | |
f46e9203 | 482 | struct pca955x_chipdef *chip; |
2420ae02 | 483 | struct led_classdev *led; |
f46e9203 | 484 | struct i2c_adapter *adapter; |
95bf14bf | 485 | int i, err; |
ed1f4b96 | 486 | struct pca955x_platform_data *pdata; |
561099a1 | 487 | int ngpios = 0; |
f46e9203 | 488 | |
5b6cd445 | 489 | chip = &pca955x_chipdefs[id->driver_data]; |
1c57d9bd | 490 | adapter = client->adapter; |
87aae1ea | 491 | pdata = dev_get_platdata(&client->dev); |
ed1f4b96 | 492 | if (!pdata) { |
967f69de | 493 | pdata = pca955x_get_pdata(client, chip); |
ed1f4b96 CLG |
494 | if (IS_ERR(pdata)) |
495 | return PTR_ERR(pdata); | |
496 | } | |
f46e9203 NC |
497 | |
498 | /* Make sure the slave address / chip type combo given is possible */ | |
499 | if ((client->addr & ~((1 << chip->slv_addr_shift) - 1)) != | |
500 | chip->slv_addr) { | |
501 | dev_err(&client->dev, "invalid slave address %02x\n", | |
2420ae02 | 502 | client->addr); |
f46e9203 NC |
503 | return -ENODEV; |
504 | } | |
505 | ||
b40b0c17 | 506 | dev_info(&client->dev, "leds-pca955x: Using %s %d-bit LED driver at " |
2420ae02 EJ |
507 | "slave address 0x%02x\n", client->name, chip->bits, |
508 | client->addr); | |
f46e9203 | 509 | |
aace34c0 | 510 | if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) |
f46e9203 NC |
511 | return -EIO; |
512 | ||
ed1f4b96 CLG |
513 | if (pdata->num_leds != chip->bits) { |
514 | dev_err(&client->dev, | |
515 | "board info claims %d LEDs on a %d-bit chip\n", | |
516 | pdata->num_leds, chip->bits); | |
517 | return -ENODEV; | |
f46e9203 NC |
518 | } |
519 | ||
73759f6a | 520 | pca955x = devm_kzalloc(&client->dev, sizeof(*pca955x), GFP_KERNEL); |
95bf14bf SW |
521 | if (!pca955x) |
522 | return -ENOMEM; | |
523 | ||
2420ae02 EJ |
524 | pca955x->leds = devm_kcalloc(&client->dev, chip->bits, |
525 | sizeof(*pca955x_led), GFP_KERNEL); | |
73759f6a BW |
526 | if (!pca955x->leds) |
527 | return -ENOMEM; | |
e7e11d8b | 528 | |
95bf14bf SW |
529 | i2c_set_clientdata(client, pca955x); |
530 | ||
e7e11d8b AS |
531 | mutex_init(&pca955x->lock); |
532 | pca955x->client = client; | |
533 | pca955x->chipdef = chip; | |
534 | ||
f46e9203 | 535 | for (i = 0; i < chip->bits; i++) { |
e7e11d8b AS |
536 | pca955x_led = &pca955x->leds[i]; |
537 | pca955x_led->led_num = i; | |
538 | pca955x_led->pca955x = pca955x; | |
561099a1 CLG |
539 | pca955x_led->type = pdata->leds[i].type; |
540 | ||
541 | switch (pca955x_led->type) { | |
542 | case PCA955X_TYPE_NONE: | |
543 | break; | |
544 | case PCA955X_TYPE_GPIO: | |
545 | ngpios++; | |
546 | break; | |
547 | case PCA955X_TYPE_LED: | |
548 | /* | |
549 | * Platform data can specify LED names and | |
550 | * default triggers | |
551 | */ | |
390c97dc JA |
552 | if (pdata->leds[i].name[0] == '\0') |
553 | snprintf(pdata->leds[i].name, | |
2420ae02 | 554 | sizeof(pdata->leds[i].name), "%d", i); |
390c97dc | 555 | |
2420ae02 EJ |
556 | snprintf(pca955x_led->name, sizeof(pca955x_led->name), |
557 | "pca955x:%s", pdata->leds[i].name); | |
390c97dc | 558 | |
2420ae02 | 559 | led = &pca955x_led->led_cdev; |
f46e9203 | 560 | if (pdata->leds[i].default_trigger) |
2420ae02 | 561 | led->default_trigger = |
f46e9203 | 562 | pdata->leds[i].default_trigger; |
f46e9203 | 563 | |
2420ae02 EJ |
564 | led->name = pca955x_led->name; |
565 | led->brightness_set_blocking = pca955x_led_set; | |
7086625f | 566 | led->brightness_get = pca955x_led_get; |
f46e9203 | 567 | |
2420ae02 | 568 | err = devm_led_classdev_register(&client->dev, led); |
561099a1 CLG |
569 | if (err) |
570 | return err; | |
f46e9203 | 571 | |
561099a1 | 572 | /* Turn off LED */ |
2420ae02 | 573 | err = pca955x_led_set(led, LED_OFF); |
1591caf2 CLG |
574 | if (err) |
575 | return err; | |
561099a1 CLG |
576 | } |
577 | } | |
f46e9203 NC |
578 | |
579 | /* PWM0 is used for half brightness or 50% duty cycle */ | |
1591caf2 CLG |
580 | err = pca955x_write_pwm(client, 0, 255 - LED_HALF); |
581 | if (err) | |
582 | return err; | |
f46e9203 NC |
583 | |
584 | /* PWM1 is used for variable brightness, default to OFF */ | |
1591caf2 CLG |
585 | err = pca955x_write_pwm(client, 1, 0); |
586 | if (err) | |
587 | return err; | |
f46e9203 NC |
588 | |
589 | /* Set to fast frequency so we do not see flashing */ | |
1591caf2 CLG |
590 | err = pca955x_write_psc(client, 0, 0); |
591 | if (err) | |
592 | return err; | |
593 | err = pca955x_write_psc(client, 1, 0); | |
594 | if (err) | |
595 | return err; | |
f46e9203 | 596 | |
561099a1 CLG |
597 | #ifdef CONFIG_LEDS_PCA955X_GPIO |
598 | if (ngpios) { | |
599 | pca955x->gpio.label = "gpio-pca955x"; | |
600 | pca955x->gpio.direction_input = pca955x_gpio_direction_input; | |
601 | pca955x->gpio.direction_output = pca955x_gpio_direction_output; | |
602 | pca955x->gpio.set = pca955x_gpio_set_value; | |
603 | pca955x->gpio.get = pca955x_gpio_get_value; | |
604 | pca955x->gpio.request = pca955x_gpio_request_pin; | |
605 | pca955x->gpio.can_sleep = 1; | |
606 | pca955x->gpio.base = -1; | |
607 | pca955x->gpio.ngpio = ngpios; | |
608 | pca955x->gpio.parent = &client->dev; | |
609 | pca955x->gpio.owner = THIS_MODULE; | |
610 | ||
611 | err = devm_gpiochip_add_data(&client->dev, &pca955x->gpio, | |
612 | pca955x); | |
613 | if (err) { | |
614 | /* Use data->gpio.dev as a flag for freeing gpiochip */ | |
615 | pca955x->gpio.parent = NULL; | |
616 | dev_warn(&client->dev, "could not add gpiochip\n"); | |
617 | return err; | |
618 | } | |
619 | dev_info(&client->dev, "gpios %i...%i\n", | |
620 | pca955x->gpio.base, pca955x->gpio.base + | |
621 | pca955x->gpio.ngpio - 1); | |
622 | } | |
623 | #endif | |
624 | ||
f46e9203 | 625 | return 0; |
f46e9203 NC |
626 | } |
627 | ||
628 | static struct i2c_driver pca955x_driver = { | |
629 | .driver = { | |
630 | .name = "leds-pca955x", | |
967f69de | 631 | .of_match_table = of_pca955x_match, |
f46e9203 NC |
632 | }, |
633 | .probe = pca955x_probe, | |
f46e9203 NC |
634 | .id_table = pca955x_id, |
635 | }; | |
636 | ||
09a0d183 | 637 | module_i2c_driver(pca955x_driver); |
f46e9203 NC |
638 | |
639 | MODULE_AUTHOR("Nate Case <ncase@xes-inc.com>"); | |
640 | MODULE_DESCRIPTION("PCA955x LED driver"); | |
641 | MODULE_LICENSE("GPL v2"); |