Commit | Line | Data |
---|---|---|
e63b68de MS |
1 | /* $Id: cris-ide-driver.patch,v 1.1 2005/06/29 21:39:07 akpm Exp $ |
2 | * | |
3 | * Etrax specific IDE functions, like init and PIO-mode setting etc. | |
4 | * Almost the entire ide.c is used for the rest of the Etrax ATA driver. | |
5 | * Copyright (c) 2000-2005 Axis Communications AB | |
6 | * | |
7 | * Authors: Bjorn Wesen (initial version) | |
8 | * Mikael Starvik (crisv32 port) | |
9 | */ | |
10 | ||
11 | /* Regarding DMA: | |
12 | * | |
13 | * There are two forms of DMA - "DMA handshaking" between the interface and the drive, | |
14 | * and DMA between the memory and the interface. We can ALWAYS use the latter, since it's | |
15 | * something built-in in the Etrax. However only some drives support the DMA-mode handshaking | |
16 | * on the ATA-bus. The normal PC driver and Triton interface disables memory-if DMA when the | |
17 | * device can't do DMA handshaking for some stupid reason. We don't need to do that. | |
18 | */ | |
19 | ||
e63b68de MS |
20 | #include <linux/types.h> |
21 | #include <linux/kernel.h> | |
22 | #include <linux/timer.h> | |
23 | #include <linux/mm.h> | |
24 | #include <linux/interrupt.h> | |
25 | #include <linux/delay.h> | |
26 | #include <linux/blkdev.h> | |
27 | #include <linux/hdreg.h> | |
28 | #include <linux/ide.h> | |
29 | #include <linux/init.h> | |
30 | ||
31 | #include <asm/io.h> | |
32 | #include <asm/dma.h> | |
33 | ||
34 | /* number of DMA descriptors */ | |
35 | #define MAX_DMA_DESCRS 64 | |
36 | ||
37 | /* number of times to retry busy-flags when reading/writing IDE-registers | |
38 | * this can't be too high because a hung harddisk might cause the watchdog | |
39 | * to trigger (sometimes INB and OUTB are called with irq's disabled) | |
40 | */ | |
41 | ||
42 | #define IDE_REGISTER_TIMEOUT 300 | |
43 | ||
44 | #define LOWDB(x) | |
45 | #define D(x) | |
46 | ||
47 | enum /* Transfer types */ | |
48 | { | |
49 | TYPE_PIO, | |
50 | TYPE_DMA, | |
51 | TYPE_UDMA | |
52 | }; | |
53 | ||
54 | /* CRISv32 specifics */ | |
55 | #ifdef CONFIG_ETRAX_ARCH_V32 | |
56 | #include <asm/arch/hwregs/ata_defs.h> | |
57 | #include <asm/arch/hwregs/dma_defs.h> | |
58 | #include <asm/arch/hwregs/dma.h> | |
59 | #include <asm/arch/pinmux.h> | |
60 | ||
61 | #define ATA_UDMA2_CYC 2 | |
62 | #define ATA_UDMA2_DVS 3 | |
63 | #define ATA_UDMA1_CYC 2 | |
64 | #define ATA_UDMA1_DVS 4 | |
65 | #define ATA_UDMA0_CYC 4 | |
66 | #define ATA_UDMA0_DVS 6 | |
67 | #define ATA_DMA2_STROBE 7 | |
68 | #define ATA_DMA2_HOLD 1 | |
69 | #define ATA_DMA1_STROBE 8 | |
70 | #define ATA_DMA1_HOLD 3 | |
71 | #define ATA_DMA0_STROBE 25 | |
72 | #define ATA_DMA0_HOLD 19 | |
73 | #define ATA_PIO4_SETUP 3 | |
74 | #define ATA_PIO4_STROBE 7 | |
75 | #define ATA_PIO4_HOLD 1 | |
76 | #define ATA_PIO3_SETUP 3 | |
77 | #define ATA_PIO3_STROBE 9 | |
78 | #define ATA_PIO3_HOLD 3 | |
79 | #define ATA_PIO2_SETUP 3 | |
80 | #define ATA_PIO2_STROBE 13 | |
81 | #define ATA_PIO2_HOLD 5 | |
82 | #define ATA_PIO1_SETUP 5 | |
83 | #define ATA_PIO1_STROBE 23 | |
84 | #define ATA_PIO1_HOLD 9 | |
85 | #define ATA_PIO0_SETUP 9 | |
86 | #define ATA_PIO0_STROBE 39 | |
87 | #define ATA_PIO0_HOLD 9 | |
88 | ||
89 | int | |
90 | cris_ide_ack_intr(ide_hwif_t* hwif) | |
91 | { | |
92 | reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2, | |
93 | int, hwif->io_ports[0]); | |
94 | REG_WR_INT(ata, regi_ata, rw_ack_intr, 1 << ctrl2.sel); | |
95 | return 1; | |
96 | } | |
97 | ||
98 | static inline int | |
99 | cris_ide_busy(void) | |
100 | { | |
101 | reg_ata_rs_stat_data stat_data; | |
102 | stat_data = REG_RD(ata, regi_ata, rs_stat_data); | |
103 | return stat_data.busy; | |
104 | } | |
105 | ||
106 | static inline int | |
107 | cris_ide_ready(void) | |
108 | { | |
109 | return !cris_ide_busy(); | |
110 | } | |
111 | ||
112 | static inline int | |
113 | cris_ide_data_available(unsigned short* data) | |
114 | { | |
115 | reg_ata_rs_stat_data stat_data; | |
116 | stat_data = REG_RD(ata, regi_ata, rs_stat_data); | |
117 | *data = stat_data.data; | |
118 | return stat_data.dav; | |
119 | } | |
120 | ||
121 | static void | |
122 | cris_ide_write_command(unsigned long command) | |
123 | { | |
124 | REG_WR_INT(ata, regi_ata, rw_ctrl2, command); /* write data to the drive's register */ | |
125 | } | |
126 | ||
127 | static void | |
128 | cris_ide_set_speed(int type, int setup, int strobe, int hold) | |
129 | { | |
130 | reg_ata_rw_ctrl0 ctrl0 = REG_RD(ata, regi_ata, rw_ctrl0); | |
131 | reg_ata_rw_ctrl1 ctrl1 = REG_RD(ata, regi_ata, rw_ctrl1); | |
132 | ||
133 | if (type == TYPE_PIO) { | |
134 | ctrl0.pio_setup = setup; | |
135 | ctrl0.pio_strb = strobe; | |
136 | ctrl0.pio_hold = hold; | |
137 | } else if (type == TYPE_DMA) { | |
138 | ctrl0.dma_strb = strobe; | |
139 | ctrl0.dma_hold = hold; | |
140 | } else if (type == TYPE_UDMA) { | |
141 | ctrl1.udma_tcyc = setup; | |
142 | ctrl1.udma_tdvs = strobe; | |
143 | } | |
144 | REG_WR(ata, regi_ata, rw_ctrl0, ctrl0); | |
145 | REG_WR(ata, regi_ata, rw_ctrl1, ctrl1); | |
146 | } | |
147 | ||
148 | static unsigned long | |
149 | cris_ide_base_address(int bus) | |
150 | { | |
151 | reg_ata_rw_ctrl2 ctrl2 = {0}; | |
152 | ctrl2.sel = bus; | |
153 | return REG_TYPE_CONV(int, reg_ata_rw_ctrl2, ctrl2); | |
154 | } | |
155 | ||
156 | static unsigned long | |
157 | cris_ide_reg_addr(unsigned long addr, int cs0, int cs1) | |
158 | { | |
159 | reg_ata_rw_ctrl2 ctrl2 = {0}; | |
160 | ctrl2.addr = addr; | |
161 | ctrl2.cs1 = cs1; | |
162 | ctrl2.cs0 = cs0; | |
163 | return REG_TYPE_CONV(int, reg_ata_rw_ctrl2, ctrl2); | |
164 | } | |
165 | ||
166 | static __init void | |
167 | cris_ide_reset(unsigned val) | |
168 | { | |
169 | reg_ata_rw_ctrl0 ctrl0 = {0}; | |
170 | ctrl0.rst = val ? regk_ata_active : regk_ata_inactive; | |
171 | REG_WR(ata, regi_ata, rw_ctrl0, ctrl0); | |
172 | } | |
173 | ||
174 | static __init void | |
175 | cris_ide_init(void) | |
176 | { | |
177 | reg_ata_rw_ctrl0 ctrl0 = {0}; | |
178 | reg_ata_rw_intr_mask intr_mask = {0}; | |
179 | ||
180 | ctrl0.en = regk_ata_yes; | |
181 | REG_WR(ata, regi_ata, rw_ctrl0, ctrl0); | |
182 | ||
183 | intr_mask.bus0 = regk_ata_yes; | |
184 | intr_mask.bus1 = regk_ata_yes; | |
185 | intr_mask.bus2 = regk_ata_yes; | |
186 | intr_mask.bus3 = regk_ata_yes; | |
187 | ||
188 | REG_WR(ata, regi_ata, rw_intr_mask, intr_mask); | |
189 | ||
190 | crisv32_request_dma(2, "ETRAX FS built-in ATA", DMA_VERBOSE_ON_ERROR, 0, dma_ata); | |
191 | crisv32_request_dma(3, "ETRAX FS built-in ATA", DMA_VERBOSE_ON_ERROR, 0, dma_ata); | |
192 | ||
193 | crisv32_pinmux_alloc_fixed(pinmux_ata); | |
194 | crisv32_pinmux_alloc_fixed(pinmux_ata0); | |
195 | crisv32_pinmux_alloc_fixed(pinmux_ata1); | |
196 | crisv32_pinmux_alloc_fixed(pinmux_ata2); | |
197 | crisv32_pinmux_alloc_fixed(pinmux_ata3); | |
198 | ||
199 | DMA_RESET(regi_dma2); | |
200 | DMA_ENABLE(regi_dma2); | |
201 | DMA_RESET(regi_dma3); | |
202 | DMA_ENABLE(regi_dma3); | |
203 | ||
204 | DMA_WR_CMD (regi_dma2, regk_dma_set_w_size2); | |
205 | DMA_WR_CMD (regi_dma3, regk_dma_set_w_size2); | |
206 | } | |
207 | ||
208 | static dma_descr_context mycontext __attribute__ ((__aligned__(32))); | |
209 | ||
210 | #define cris_dma_descr_type dma_descr_data | |
211 | #define cris_pio_read regk_ata_rd | |
212 | #define cris_ultra_mask 0x7 | |
213 | #define MAX_DESCR_SIZE 0xffffffffUL | |
214 | ||
215 | static unsigned long | |
216 | cris_ide_get_reg(unsigned long reg) | |
217 | { | |
218 | return (reg & 0x0e000000) >> 25; | |
219 | } | |
220 | ||
221 | static void | |
222 | cris_ide_fill_descriptor(cris_dma_descr_type *d, void* buf, unsigned int len, int last) | |
223 | { | |
224 | d->buf = (char*)virt_to_phys(buf); | |
225 | d->after = d->buf + len; | |
226 | d->eol = last; | |
227 | } | |
228 | ||
229 | static void | |
230 | cris_ide_start_dma(ide_drive_t *drive, cris_dma_descr_type *d, int dir,int type,int len) | |
231 | { | |
232 | reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2, int, IDE_DATA_REG); | |
233 | reg_ata_rw_trf_cnt trf_cnt = {0}; | |
234 | ||
235 | mycontext.saved_data = (dma_descr_data*)virt_to_phys(d); | |
236 | mycontext.saved_data_buf = d->buf; | |
237 | /* start the dma channel */ | |
238 | DMA_START_CONTEXT(dir ? regi_dma3 : regi_dma2, virt_to_phys(&mycontext)); | |
239 | ||
240 | /* initiate a multi word dma read using PIO handshaking */ | |
241 | trf_cnt.cnt = len >> 1; | |
242 | /* Due to a "feature" the transfer count has to be one extra word for UDMA. */ | |
243 | if (type == TYPE_UDMA) | |
244 | trf_cnt.cnt++; | |
245 | REG_WR(ata, regi_ata, rw_trf_cnt, trf_cnt); | |
246 | ||
247 | ctrl2.rw = dir ? regk_ata_rd : regk_ata_wr; | |
248 | ctrl2.trf_mode = regk_ata_dma; | |
249 | ctrl2.hsh = type == TYPE_PIO ? regk_ata_pio : | |
250 | type == TYPE_DMA ? regk_ata_dma : regk_ata_udma; | |
251 | ctrl2.multi = regk_ata_yes; | |
252 | ctrl2.dma_size = regk_ata_word; | |
253 | REG_WR(ata, regi_ata, rw_ctrl2, ctrl2); | |
254 | } | |
255 | ||
256 | static void | |
257 | cris_ide_wait_dma(int dir) | |
258 | { | |
259 | reg_dma_rw_stat status; | |
260 | do | |
261 | { | |
262 | status = REG_RD(dma, dir ? regi_dma3 : regi_dma2, rw_stat); | |
263 | } while(status.list_state != regk_dma_data_at_eol); | |
264 | } | |
265 | ||
266 | static int cris_dma_test_irq(ide_drive_t *drive) | |
267 | { | |
268 | int intr = REG_RD_INT(ata, regi_ata, r_intr); | |
269 | reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2, int, IDE_DATA_REG); | |
270 | return intr & (1 << ctrl2.sel) ? 1 : 0; | |
271 | } | |
272 | ||
273 | static void cris_ide_initialize_dma(int dir) | |
274 | { | |
275 | } | |
276 | ||
277 | #else | |
278 | /* CRISv10 specifics */ | |
279 | #include <asm/arch/svinto.h> | |
280 | #include <asm/arch/io_interface_mux.h> | |
281 | ||
282 | /* PIO timing (in R_ATA_CONFIG) | |
283 | * | |
284 | * _____________________________ | |
285 | * ADDRESS : ________/ | |
286 | * | |
287 | * _______________ | |
288 | * DIOR : ____________/ \__________ | |
289 | * | |
290 | * _______________ | |
291 | * DATA : XXXXXXXXXXXXXXXX_______________XXXXXXXX | |
292 | * | |
293 | * | |
294 | * DIOR is unbuffered while address and data is buffered. | |
295 | * This creates two problems: | |
296 | * 1. The DIOR pulse is to early (because it is unbuffered) | |
297 | * 2. The rise time of DIOR is long | |
298 | * | |
299 | * There are at least three different plausible solutions | |
300 | * 1. Use a pad capable of larger currents in Etrax | |
301 | * 2. Use an external buffer | |
302 | * 3. Make the strobe pulse longer | |
303 | * | |
304 | * Some of the strobe timings below are modified to compensate | |
305 | * for this. This implies a slight performance decrease. | |
306 | * | |
307 | * THIS SHOULD NEVER BE CHANGED! | |
308 | * | |
309 | * TODO: Is this true for the latest LX boards still ? | |
310 | */ | |
311 | ||
312 | #define ATA_UDMA2_CYC 0 /* No UDMA supported, just to make it compile. */ | |
313 | #define ATA_UDMA2_DVS 0 | |
314 | #define ATA_UDMA1_CYC 0 | |
315 | #define ATA_UDMA1_DVS 0 | |
316 | #define ATA_UDMA0_CYC 0 | |
317 | #define ATA_UDMA0_DVS 0 | |
318 | #define ATA_DMA2_STROBE 4 | |
319 | #define ATA_DMA2_HOLD 0 | |
320 | #define ATA_DMA1_STROBE 4 | |
321 | #define ATA_DMA1_HOLD 1 | |
322 | #define ATA_DMA0_STROBE 12 | |
323 | #define ATA_DMA0_HOLD 9 | |
324 | #define ATA_PIO4_SETUP 1 | |
325 | #define ATA_PIO4_STROBE 5 | |
326 | #define ATA_PIO4_HOLD 0 | |
327 | #define ATA_PIO3_SETUP 1 | |
328 | #define ATA_PIO3_STROBE 5 | |
329 | #define ATA_PIO3_HOLD 1 | |
330 | #define ATA_PIO2_SETUP 1 | |
331 | #define ATA_PIO2_STROBE 6 | |
332 | #define ATA_PIO2_HOLD 2 | |
333 | #define ATA_PIO1_SETUP 2 | |
334 | #define ATA_PIO1_STROBE 11 | |
335 | #define ATA_PIO1_HOLD 4 | |
336 | #define ATA_PIO0_SETUP 4 | |
337 | #define ATA_PIO0_STROBE 19 | |
338 | #define ATA_PIO0_HOLD 4 | |
339 | ||
340 | int | |
341 | cris_ide_ack_intr(ide_hwif_t* hwif) | |
342 | { | |
343 | return 1; | |
344 | } | |
345 | ||
346 | static inline int | |
347 | cris_ide_busy(void) | |
348 | { | |
349 | return *R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy) ; | |
350 | } | |
351 | ||
352 | static inline int | |
353 | cris_ide_ready(void) | |
354 | { | |
355 | return *R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, tr_rdy) ; | |
356 | } | |
357 | ||
358 | static inline int | |
359 | cris_ide_data_available(unsigned short* data) | |
360 | { | |
361 | unsigned long status = *R_ATA_STATUS_DATA; | |
362 | *data = (unsigned short)status; | |
363 | return status & IO_MASK(R_ATA_STATUS_DATA, dav); | |
364 | } | |
365 | ||
366 | static void | |
367 | cris_ide_write_command(unsigned long command) | |
368 | { | |
369 | *R_ATA_CTRL_DATA = command; | |
370 | } | |
371 | ||
372 | static void | |
373 | cris_ide_set_speed(int type, int setup, int strobe, int hold) | |
374 | { | |
375 | static int pio_setup = ATA_PIO4_SETUP; | |
376 | static int pio_strobe = ATA_PIO4_STROBE; | |
377 | static int pio_hold = ATA_PIO4_HOLD; | |
378 | static int dma_strobe = ATA_DMA2_STROBE; | |
379 | static int dma_hold = ATA_DMA2_HOLD; | |
380 | ||
381 | if (type == TYPE_PIO) { | |
382 | pio_setup = setup; | |
383 | pio_strobe = strobe; | |
384 | pio_hold = hold; | |
385 | } else if (type == TYPE_DMA) { | |
386 | dma_strobe = strobe; | |
387 | dma_hold = hold; | |
388 | } | |
389 | *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ) | | |
390 | IO_FIELD( R_ATA_CONFIG, dma_strobe, dma_strobe ) | | |
391 | IO_FIELD( R_ATA_CONFIG, dma_hold, dma_hold ) | | |
392 | IO_FIELD( R_ATA_CONFIG, pio_setup, pio_setup ) | | |
393 | IO_FIELD( R_ATA_CONFIG, pio_strobe, pio_strobe ) | | |
394 | IO_FIELD( R_ATA_CONFIG, pio_hold, pio_hold ) ); | |
395 | } | |
396 | ||
397 | static unsigned long | |
398 | cris_ide_base_address(int bus) | |
399 | { | |
400 | return IO_FIELD(R_ATA_CTRL_DATA, sel, bus); | |
401 | } | |
402 | ||
403 | static unsigned long | |
404 | cris_ide_reg_addr(unsigned long addr, int cs0, int cs1) | |
405 | { | |
406 | return IO_FIELD(R_ATA_CTRL_DATA, addr, addr) | | |
407 | IO_FIELD(R_ATA_CTRL_DATA, cs0, cs0) | | |
408 | IO_FIELD(R_ATA_CTRL_DATA, cs1, cs1); | |
409 | } | |
410 | ||
411 | static __init void | |
412 | cris_ide_reset(unsigned val) | |
413 | { | |
414 | #ifdef CONFIG_ETRAX_IDE_G27_RESET | |
415 | REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, 27, val); | |
416 | #endif | |
e63b68de MS |
417 | #ifdef CONFIG_ETRAX_IDE_PB7_RESET |
418 | port_pb_dir_shadow = port_pb_dir_shadow | | |
419 | IO_STATE(R_PORT_PB_DIR, dir7, output); | |
420 | *R_PORT_PB_DIR = port_pb_dir_shadow; | |
421 | REG_SHADOW_SET(R_PORT_PB_DATA, port_pb_data_shadow, 7, val); | |
422 | #endif | |
423 | } | |
424 | ||
425 | static __init void | |
426 | cris_ide_init(void) | |
427 | { | |
428 | volatile unsigned int dummy; | |
429 | ||
430 | *R_ATA_CTRL_DATA = 0; | |
431 | *R_ATA_TRANSFER_CNT = 0; | |
432 | *R_ATA_CONFIG = 0; | |
433 | ||
434 | if (cris_request_io_interface(if_ata, "ETRAX100LX IDE")) { | |
435 | printk(KERN_CRIT "ide: Failed to get IO interface\n"); | |
436 | return; | |
437 | } else if (cris_request_dma(ATA_TX_DMA_NBR, | |
438 | "ETRAX100LX IDE TX", | |
439 | DMA_VERBOSE_ON_ERROR, | |
440 | dma_ata)) { | |
441 | cris_free_io_interface(if_ata); | |
442 | printk(KERN_CRIT "ide: Failed to get Tx DMA channel\n"); | |
443 | return; | |
444 | } else if (cris_request_dma(ATA_RX_DMA_NBR, | |
445 | "ETRAX100LX IDE RX", | |
446 | DMA_VERBOSE_ON_ERROR, | |
447 | dma_ata)) { | |
448 | cris_free_dma(ATA_TX_DMA_NBR, "ETRAX100LX IDE Tx"); | |
449 | cris_free_io_interface(if_ata); | |
450 | printk(KERN_CRIT "ide: Failed to get Rx DMA channel\n"); | |
451 | return; | |
452 | } | |
453 | ||
454 | /* make a dummy read to set the ata controller in a proper state */ | |
455 | dummy = *R_ATA_STATUS_DATA; | |
456 | ||
457 | *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 )); | |
458 | *R_ATA_CTRL_DATA = ( IO_STATE( R_ATA_CTRL_DATA, rw, read) | | |
459 | IO_FIELD( R_ATA_CTRL_DATA, addr, 1 ) ); | |
460 | ||
461 | while(*R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy)); /* wait for busy flag*/ | |
462 | ||
463 | *R_IRQ_MASK0_SET = ( IO_STATE( R_IRQ_MASK0_SET, ata_irq0, set ) | | |
464 | IO_STATE( R_IRQ_MASK0_SET, ata_irq1, set ) | | |
465 | IO_STATE( R_IRQ_MASK0_SET, ata_irq2, set ) | | |
466 | IO_STATE( R_IRQ_MASK0_SET, ata_irq3, set ) ); | |
467 | ||
468 | /* reset the dma channels we will use */ | |
469 | ||
470 | RESET_DMA(ATA_TX_DMA_NBR); | |
471 | RESET_DMA(ATA_RX_DMA_NBR); | |
472 | WAIT_DMA(ATA_TX_DMA_NBR); | |
473 | WAIT_DMA(ATA_RX_DMA_NBR); | |
474 | } | |
475 | ||
476 | #define cris_dma_descr_type etrax_dma_descr | |
477 | #define cris_pio_read IO_STATE(R_ATA_CTRL_DATA, rw, read) | |
478 | #define cris_ultra_mask 0x0 | |
479 | #define MAX_DESCR_SIZE 0x10000UL | |
480 | ||
481 | static unsigned long | |
482 | cris_ide_get_reg(unsigned long reg) | |
483 | { | |
484 | return (reg & 0x0e000000) >> 25; | |
485 | } | |
486 | ||
487 | static void | |
488 | cris_ide_fill_descriptor(cris_dma_descr_type *d, void* buf, unsigned int len, int last) | |
489 | { | |
490 | d->buf = virt_to_phys(buf); | |
491 | d->sw_len = len == MAX_DESCR_SIZE ? 0 : len; | |
492 | if (last) | |
493 | d->ctrl |= d_eol; | |
494 | } | |
495 | ||
496 | static void cris_ide_start_dma(ide_drive_t *drive, cris_dma_descr_type *d, int dir, int type, int len) | |
497 | { | |
498 | unsigned long cmd; | |
499 | ||
500 | if (dir) { | |
501 | /* need to do this before RX DMA due to a chip bug | |
502 | * it is enough to just flush the part of the cache that | |
503 | * corresponds to the buffers we start, but since HD transfers | |
504 | * usually are more than 8 kB, it is easier to optimize for the | |
505 | * normal case and just flush the entire cache. its the only | |
506 | * way to be sure! (OB movie quote) | |
507 | */ | |
508 | flush_etrax_cache(); | |
509 | *R_DMA_CH3_FIRST = virt_to_phys(d); | |
510 | *R_DMA_CH3_CMD = IO_STATE(R_DMA_CH3_CMD, cmd, start); | |
511 | ||
512 | } else { | |
513 | *R_DMA_CH2_FIRST = virt_to_phys(d); | |
514 | *R_DMA_CH2_CMD = IO_STATE(R_DMA_CH2_CMD, cmd, start); | |
515 | } | |
516 | ||
517 | /* initiate a multi word dma read using DMA handshaking */ | |
518 | ||
519 | *R_ATA_TRANSFER_CNT = | |
520 | IO_FIELD(R_ATA_TRANSFER_CNT, count, len >> 1); | |
521 | ||
522 | cmd = dir ? IO_STATE(R_ATA_CTRL_DATA, rw, read) : IO_STATE(R_ATA_CTRL_DATA, rw, write); | |
523 | cmd |= type == TYPE_PIO ? IO_STATE(R_ATA_CTRL_DATA, handsh, pio) : | |
524 | IO_STATE(R_ATA_CTRL_DATA, handsh, dma); | |
525 | *R_ATA_CTRL_DATA = | |
526 | cmd | | |
527 | IO_FIELD(R_ATA_CTRL_DATA, data, IDE_DATA_REG) | | |
528 | IO_STATE(R_ATA_CTRL_DATA, src_dst, dma) | | |
529 | IO_STATE(R_ATA_CTRL_DATA, multi, on) | | |
530 | IO_STATE(R_ATA_CTRL_DATA, dma_size, word); | |
531 | } | |
532 | ||
533 | static void | |
534 | cris_ide_wait_dma(int dir) | |
535 | { | |
536 | if (dir) | |
537 | WAIT_DMA(ATA_RX_DMA_NBR); | |
538 | else | |
539 | WAIT_DMA(ATA_TX_DMA_NBR); | |
540 | } | |
541 | ||
542 | static int cris_dma_test_irq(ide_drive_t *drive) | |
543 | { | |
544 | int intr = *R_IRQ_MASK0_RD; | |
545 | int bus = IO_EXTRACT(R_ATA_CTRL_DATA, sel, IDE_DATA_REG); | |
546 | return intr & (1 << (bus + IO_BITNR(R_IRQ_MASK0_RD, ata_irq0))) ? 1 : 0; | |
547 | } | |
548 | ||
549 | ||
550 | static void cris_ide_initialize_dma(int dir) | |
551 | { | |
552 | if (dir) | |
553 | { | |
554 | RESET_DMA(ATA_RX_DMA_NBR); /* sometimes the DMA channel get stuck so we need to do this */ | |
555 | WAIT_DMA(ATA_RX_DMA_NBR); | |
556 | } | |
557 | else | |
558 | { | |
559 | RESET_DMA(ATA_TX_DMA_NBR); /* sometimes the DMA channel get stuck so we need to do this */ | |
560 | WAIT_DMA(ATA_TX_DMA_NBR); | |
561 | } | |
562 | } | |
563 | ||
564 | #endif | |
565 | ||
566 | void | |
567 | cris_ide_outw(unsigned short data, unsigned long reg) { | |
568 | int timeleft; | |
569 | ||
570 | LOWDB(printk("ow: data 0x%x, reg 0x%x\n", data, reg)); | |
571 | ||
572 | /* note the lack of handling any timeouts. we stop waiting, but we don't | |
573 | * really notify anybody. | |
574 | */ | |
575 | ||
576 | timeleft = IDE_REGISTER_TIMEOUT; | |
577 | /* wait for busy flag */ | |
578 | do { | |
579 | timeleft--; | |
580 | } while(timeleft && cris_ide_busy()); | |
581 | ||
582 | /* | |
583 | * Fall through at a timeout, so the ongoing command will be | |
584 | * aborted by the write below, which is expected to be a dummy | |
585 | * command to the command register. This happens when a faulty | |
586 | * drive times out on a command. See comment on timeout in | |
587 | * INB. | |
588 | */ | |
589 | if(!timeleft) | |
590 | printk("ATA timeout reg 0x%lx := 0x%x\n", reg, data); | |
591 | ||
592 | cris_ide_write_command(reg|data); /* write data to the drive's register */ | |
593 | ||
594 | timeleft = IDE_REGISTER_TIMEOUT; | |
595 | /* wait for transmitter ready */ | |
596 | do { | |
597 | timeleft--; | |
598 | } while(timeleft && !cris_ide_ready()); | |
599 | } | |
600 | ||
601 | void | |
602 | cris_ide_outb(unsigned char data, unsigned long reg) | |
603 | { | |
604 | cris_ide_outw(data, reg); | |
605 | } | |
606 | ||
607 | void | |
608 | cris_ide_outbsync(ide_drive_t *drive, u8 addr, unsigned long port) | |
609 | { | |
610 | cris_ide_outw(addr, port); | |
611 | } | |
612 | ||
613 | unsigned short | |
614 | cris_ide_inw(unsigned long reg) { | |
615 | int timeleft; | |
616 | unsigned short val; | |
617 | ||
618 | timeleft = IDE_REGISTER_TIMEOUT; | |
619 | /* wait for busy flag */ | |
620 | do { | |
621 | timeleft--; | |
622 | } while(timeleft && cris_ide_busy()); | |
623 | ||
624 | if(!timeleft) { | |
625 | /* | |
626 | * If we're asked to read the status register, like for | |
627 | * example when a command does not complete for an | |
628 | * extended time, but the ATA interface is stuck in a | |
629 | * busy state at the *ETRAX* ATA interface level (as has | |
630 | * happened repeatedly with at least one bad disk), then | |
631 | * the best thing to do is to pretend that we read | |
632 | * "busy" in the status register, so the IDE driver will | |
633 | * time-out, abort the ongoing command and perform a | |
634 | * reset sequence. Note that the subsequent OUT_BYTE | |
635 | * call will also timeout on busy, but as long as the | |
636 | * write is still performed, everything will be fine. | |
637 | */ | |
638 | if (cris_ide_get_reg(reg) == IDE_STATUS_OFFSET) | |
639 | return BUSY_STAT; | |
640 | else | |
641 | /* For other rare cases we assume 0 is good enough. */ | |
642 | return 0; | |
643 | } | |
644 | ||
645 | cris_ide_write_command(reg | cris_pio_read); | |
646 | ||
647 | timeleft = IDE_REGISTER_TIMEOUT; | |
648 | /* wait for available */ | |
649 | do { | |
650 | timeleft--; | |
651 | } while(timeleft && !cris_ide_data_available(&val)); | |
652 | ||
653 | if(!timeleft) | |
654 | return 0; | |
655 | ||
656 | LOWDB(printk("inb: 0x%x from reg 0x%x\n", val & 0xff, reg)); | |
657 | ||
658 | return val; | |
659 | } | |
660 | ||
661 | unsigned char | |
662 | cris_ide_inb(unsigned long reg) | |
663 | { | |
664 | return (unsigned char)cris_ide_inw(reg); | |
665 | } | |
666 | ||
e63b68de MS |
667 | static int cris_dma_end (ide_drive_t *drive); |
668 | static int cris_dma_setup (ide_drive_t *drive); | |
669 | static void cris_dma_exec_cmd (ide_drive_t *drive, u8 command); | |
670 | static int cris_dma_test_irq(ide_drive_t *drive); | |
671 | static void cris_dma_start(ide_drive_t *drive); | |
672 | static void cris_ide_input_data (ide_drive_t *drive, void *, unsigned int); | |
673 | static void cris_ide_output_data (ide_drive_t *drive, void *, unsigned int); | |
674 | static void cris_atapi_input_bytes(ide_drive_t *drive, void *, unsigned int); | |
675 | static void cris_atapi_output_bytes(ide_drive_t *drive, void *, unsigned int); | |
e63b68de | 676 | |
15ce926a | 677 | static void cris_dma_host_set(ide_drive_t *drive, int on) |
7469aaf6 BZ |
678 | { |
679 | } | |
680 | ||
26bcb879 | 681 | static void cris_set_pio_mode(ide_drive_t *drive, const u8 pio) |
e63b68de MS |
682 | { |
683 | int setup, strobe, hold; | |
684 | ||
685 | switch(pio) | |
686 | { | |
687 | case 0: | |
688 | setup = ATA_PIO0_SETUP; | |
689 | strobe = ATA_PIO0_STROBE; | |
690 | hold = ATA_PIO0_HOLD; | |
691 | break; | |
692 | case 1: | |
693 | setup = ATA_PIO1_SETUP; | |
694 | strobe = ATA_PIO1_STROBE; | |
695 | hold = ATA_PIO1_HOLD; | |
696 | break; | |
697 | case 2: | |
698 | setup = ATA_PIO2_SETUP; | |
699 | strobe = ATA_PIO2_STROBE; | |
700 | hold = ATA_PIO2_HOLD; | |
701 | break; | |
702 | case 3: | |
703 | setup = ATA_PIO3_SETUP; | |
704 | strobe = ATA_PIO3_STROBE; | |
705 | hold = ATA_PIO3_HOLD; | |
706 | break; | |
707 | case 4: | |
708 | setup = ATA_PIO4_SETUP; | |
709 | strobe = ATA_PIO4_STROBE; | |
710 | hold = ATA_PIO4_HOLD; | |
711 | break; | |
712 | default: | |
713 | return; | |
714 | } | |
715 | ||
716 | cris_ide_set_speed(TYPE_PIO, setup, strobe, hold); | |
717 | } | |
718 | ||
88b2b32b | 719 | static void cris_set_dma_mode(ide_drive_t *drive, const u8 speed) |
e63b68de MS |
720 | { |
721 | int cyc = 0, dvs = 0, strobe = 0, hold = 0; | |
722 | ||
e63b68de MS |
723 | switch(speed) |
724 | { | |
725 | case XFER_UDMA_0: | |
726 | cyc = ATA_UDMA0_CYC; | |
727 | dvs = ATA_UDMA0_DVS; | |
728 | break; | |
729 | case XFER_UDMA_1: | |
730 | cyc = ATA_UDMA1_CYC; | |
731 | dvs = ATA_UDMA1_DVS; | |
732 | break; | |
733 | case XFER_UDMA_2: | |
734 | cyc = ATA_UDMA2_CYC; | |
735 | dvs = ATA_UDMA2_DVS; | |
736 | break; | |
737 | case XFER_MW_DMA_0: | |
738 | strobe = ATA_DMA0_STROBE; | |
739 | hold = ATA_DMA0_HOLD; | |
740 | break; | |
741 | case XFER_MW_DMA_1: | |
742 | strobe = ATA_DMA1_STROBE; | |
743 | hold = ATA_DMA1_HOLD; | |
744 | break; | |
745 | case XFER_MW_DMA_2: | |
746 | strobe = ATA_DMA2_STROBE; | |
747 | hold = ATA_DMA2_HOLD; | |
748 | break; | |
e63b68de MS |
749 | } |
750 | ||
751 | if (speed >= XFER_UDMA_0) | |
752 | cris_ide_set_speed(TYPE_UDMA, cyc, dvs, 0); | |
753 | else | |
754 | cris_ide_set_speed(TYPE_DMA, 0, strobe, hold); | |
e63b68de MS |
755 | } |
756 | ||
757 | void __init | |
758 | init_e100_ide (void) | |
759 | { | |
760 | hw_regs_t hw; | |
761 | int ide_offsets[IDE_NR_PORTS]; | |
762 | int h; | |
763 | int i; | |
764 | ||
765 | printk("ide: ETRAX FS built-in ATA DMA controller\n"); | |
766 | ||
767 | for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++) | |
768 | ide_offsets[i] = cris_ide_reg_addr(i, 0, 1); | |
769 | ||
770 | /* the IDE control register is at ATA address 6, with CS1 active instead of CS0 */ | |
771 | ide_offsets[IDE_CONTROL_OFFSET] = cris_ide_reg_addr(6, 1, 0); | |
772 | ||
e8160562 BZ |
773 | for (h = 0; h < 4; h++) { |
774 | ide_hwif_t *hwif = NULL; | |
e63b68de | 775 | |
e63b68de MS |
776 | ide_setup_ports(&hw, cris_ide_base_address(h), |
777 | ide_offsets, | |
778 | 0, 0, cris_ide_ack_intr, | |
779 | ide_default_irq(0)); | |
fd9bb539 | 780 | ide_register_hw(&hw, NULL, 1, &hwif); |
e8160562 BZ |
781 | if (hwif == NULL) |
782 | continue; | |
2ad1e558 | 783 | hwif->mmio = 1; |
e63b68de | 784 | hwif->chipset = ide_etrax100; |
26bcb879 | 785 | hwif->set_pio_mode = &cris_set_pio_mode; |
88b2b32b | 786 | hwif->set_dma_mode = &cris_set_dma_mode; |
e63b68de MS |
787 | hwif->ata_input_data = &cris_ide_input_data; |
788 | hwif->ata_output_data = &cris_ide_output_data; | |
789 | hwif->atapi_input_bytes = &cris_atapi_input_bytes; | |
790 | hwif->atapi_output_bytes = &cris_atapi_output_bytes; | |
15ce926a | 791 | hwif->dma_host_set = &cris_dma_host_set; |
e63b68de MS |
792 | hwif->ide_dma_end = &cris_dma_end; |
793 | hwif->dma_setup = &cris_dma_setup; | |
794 | hwif->dma_exec_cmd = &cris_dma_exec_cmd; | |
795 | hwif->ide_dma_test_irq = &cris_dma_test_irq; | |
796 | hwif->dma_start = &cris_dma_start; | |
797 | hwif->OUTB = &cris_ide_outb; | |
798 | hwif->OUTW = &cris_ide_outw; | |
799 | hwif->OUTBSYNC = &cris_ide_outbsync; | |
800 | hwif->INB = &cris_ide_inb; | |
801 | hwif->INW = &cris_ide_inw; | |
49521f97 | 802 | hwif->cbl = ATA_CBL_PATA40; |
33c1002e | 803 | hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA; |
4099d143 | 804 | hwif->pio_mask = ATA_PIO4, |
ffbcb017 BZ |
805 | hwif->drives[0].autotune = 1; |
806 | hwif->drives[1].autotune = 1; | |
e63b68de MS |
807 | hwif->ultra_mask = cris_ultra_mask; |
808 | hwif->mwdma_mask = 0x07; /* Multiword DMA 0-2 */ | |
e63b68de MS |
809 | } |
810 | ||
811 | /* Reset pulse */ | |
812 | cris_ide_reset(0); | |
813 | udelay(25); | |
814 | cris_ide_reset(1); | |
815 | ||
816 | cris_ide_init(); | |
817 | ||
818 | cris_ide_set_speed(TYPE_PIO, ATA_PIO4_SETUP, ATA_PIO4_STROBE, ATA_PIO4_HOLD); | |
819 | cris_ide_set_speed(TYPE_DMA, 0, ATA_DMA2_STROBE, ATA_DMA2_HOLD); | |
820 | cris_ide_set_speed(TYPE_UDMA, ATA_UDMA2_CYC, ATA_UDMA2_DVS, 0); | |
821 | } | |
822 | ||
e63b68de MS |
823 | static cris_dma_descr_type mydescr __attribute__ ((__aligned__(16))); |
824 | ||
825 | /* | |
826 | * The following routines are mainly used by the ATAPI drivers. | |
827 | * | |
828 | * These routines will round up any request for an odd number of bytes, | |
829 | * so if an odd bytecount is specified, be sure that there's at least one | |
830 | * extra byte allocated for the buffer. | |
831 | */ | |
832 | static void | |
833 | cris_atapi_input_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount) | |
834 | { | |
835 | D(printk("atapi_input_bytes, buffer 0x%x, count %d\n", | |
836 | buffer, bytecount)); | |
837 | ||
838 | if(bytecount & 1) { | |
839 | printk("warning, odd bytecount in cdrom_in_bytes = %d.\n", bytecount); | |
840 | bytecount++; /* to round off */ | |
841 | } | |
842 | ||
843 | /* setup DMA and start transfer */ | |
844 | ||
845 | cris_ide_fill_descriptor(&mydescr, buffer, bytecount, 1); | |
846 | cris_ide_start_dma(drive, &mydescr, 1, TYPE_PIO, bytecount); | |
847 | ||
848 | /* wait for completion */ | |
849 | LED_DISK_READ(1); | |
850 | cris_ide_wait_dma(1); | |
851 | LED_DISK_READ(0); | |
852 | } | |
853 | ||
854 | static void | |
855 | cris_atapi_output_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount) | |
856 | { | |
857 | D(printk("atapi_output_bytes, buffer 0x%x, count %d\n", | |
858 | buffer, bytecount)); | |
859 | ||
860 | if(bytecount & 1) { | |
861 | printk("odd bytecount %d in atapi_out_bytes!\n", bytecount); | |
862 | bytecount++; | |
863 | } | |
864 | ||
865 | cris_ide_fill_descriptor(&mydescr, buffer, bytecount, 1); | |
866 | cris_ide_start_dma(drive, &mydescr, 0, TYPE_PIO, bytecount); | |
867 | ||
868 | /* wait for completion */ | |
869 | ||
870 | LED_DISK_WRITE(1); | |
871 | LED_DISK_READ(1); | |
872 | cris_ide_wait_dma(0); | |
873 | LED_DISK_WRITE(0); | |
874 | } | |
875 | ||
876 | /* | |
877 | * This is used for most PIO data transfers *from* the IDE interface | |
878 | */ | |
879 | static void | |
880 | cris_ide_input_data (ide_drive_t *drive, void *buffer, unsigned int wcount) | |
881 | { | |
882 | cris_atapi_input_bytes(drive, buffer, wcount << 2); | |
883 | } | |
884 | ||
885 | /* | |
886 | * This is used for most PIO data transfers *to* the IDE interface | |
887 | */ | |
888 | static void | |
889 | cris_ide_output_data (ide_drive_t *drive, void *buffer, unsigned int wcount) | |
890 | { | |
891 | cris_atapi_output_bytes(drive, buffer, wcount << 2); | |
892 | } | |
893 | ||
894 | /* we only have one DMA channel on the chip for ATA, so we can keep these statically */ | |
895 | static cris_dma_descr_type ata_descrs[MAX_DMA_DESCRS] __attribute__ ((__aligned__(16))); | |
896 | static unsigned int ata_tot_size; | |
897 | ||
898 | /* | |
899 | * cris_ide_build_dmatable() prepares a dma request. | |
900 | * Returns 0 if all went okay, returns 1 otherwise. | |
901 | */ | |
902 | static int cris_ide_build_dmatable (ide_drive_t *drive) | |
903 | { | |
904 | ide_hwif_t *hwif = drive->hwif; | |
905 | struct scatterlist* sg; | |
906 | struct request *rq = drive->hwif->hwgroup->rq; | |
907 | unsigned long size, addr; | |
908 | unsigned int count = 0; | |
909 | int i = 0; | |
910 | ||
911 | sg = hwif->sg_table; | |
912 | ||
913 | ata_tot_size = 0; | |
914 | ||
915 | ide_map_sg(drive, rq); | |
916 | i = hwif->sg_nents; | |
917 | ||
918 | while(i) { | |
919 | /* | |
920 | * Determine addr and size of next buffer area. We assume that | |
921 | * individual virtual buffers are always composed linearly in | |
922 | * physical memory. For example, we assume that any 8kB buffer | |
923 | * is always composed of two adjacent physical 4kB pages rather | |
924 | * than two possibly non-adjacent physical 4kB pages. | |
925 | */ | |
926 | /* group sequential buffers into one large buffer */ | |
45711f1a | 927 | addr = sg_phys(sg); |
e63b68de | 928 | size = sg_dma_len(sg); |
55c16a70 JA |
929 | while (--i) { |
930 | sg = sg_next(sg); | |
45711f1a | 931 | if ((addr + size) != sg_phys(sg)) |
e63b68de MS |
932 | break; |
933 | size += sg_dma_len(sg); | |
934 | } | |
935 | ||
936 | /* did we run out of descriptors? */ | |
937 | ||
938 | if(count >= MAX_DMA_DESCRS) { | |
939 | printk("%s: too few DMA descriptors\n", drive->name); | |
940 | return 1; | |
941 | } | |
942 | ||
943 | /* however, this case is more difficult - rw_trf_cnt cannot be more | |
944 | than 65536 words per transfer, so in that case we need to either | |
945 | 1) use a DMA interrupt to re-trigger rw_trf_cnt and continue with | |
946 | the descriptors, or | |
947 | 2) simply do the request here, and get dma_intr to only ide_end_request on | |
948 | those blocks that were actually set-up for transfer. | |
949 | */ | |
950 | ||
951 | if(ata_tot_size + size > 131072) { | |
952 | printk("too large total ATA DMA request, %d + %d!\n", ata_tot_size, (int)size); | |
953 | return 1; | |
954 | } | |
955 | ||
956 | /* If size > MAX_DESCR_SIZE it has to be splitted into new descriptors. Since we | |
957 | don't handle size > 131072 only one split is necessary */ | |
958 | ||
959 | if(size > MAX_DESCR_SIZE) { | |
960 | cris_ide_fill_descriptor(&ata_descrs[count], (void*)addr, MAX_DESCR_SIZE, 0); | |
961 | count++; | |
962 | ata_tot_size += MAX_DESCR_SIZE; | |
963 | size -= MAX_DESCR_SIZE; | |
964 | addr += MAX_DESCR_SIZE; | |
965 | } | |
966 | ||
967 | cris_ide_fill_descriptor(&ata_descrs[count], (void*)addr, size,i ? 0 : 1); | |
968 | count++; | |
969 | ata_tot_size += size; | |
970 | } | |
971 | ||
972 | if (count) { | |
973 | /* return and say all is ok */ | |
974 | return 0; | |
975 | } | |
976 | ||
977 | printk("%s: empty DMA table?\n", drive->name); | |
978 | return 1; /* let the PIO routines handle this weirdness */ | |
979 | } | |
980 | ||
e63b68de MS |
981 | /* |
982 | * cris_dma_intr() is the handler for disk read/write DMA interrupts | |
983 | */ | |
984 | static ide_startstop_t cris_dma_intr (ide_drive_t *drive) | |
985 | { | |
986 | LED_DISK_READ(0); | |
987 | LED_DISK_WRITE(0); | |
988 | ||
989 | return ide_dma_intr(drive); | |
990 | } | |
991 | ||
992 | /* | |
993 | * Functions below initiates/aborts DMA read/write operations on a drive. | |
994 | * | |
995 | * The caller is assumed to have selected the drive and programmed the drive's | |
996 | * sector address using CHS or LBA. All that remains is to prepare for DMA | |
997 | * and then issue the actual read/write DMA/PIO command to the drive. | |
998 | * | |
999 | * For ATAPI devices, we just prepare for DMA and return. The caller should | |
1000 | * then issue the packet command to the drive and call us again with | |
1001 | * cris_dma_start afterwards. | |
1002 | * | |
1003 | * Returns 0 if all went well. | |
1004 | * Returns 1 if DMA read/write could not be started, in which case | |
1005 | * the caller should revert to PIO for the current request. | |
1006 | */ | |
1007 | ||
e63b68de MS |
1008 | static int cris_dma_end(ide_drive_t *drive) |
1009 | { | |
1010 | drive->waiting_for_dma = 0; | |
1011 | return 0; | |
1012 | } | |
1013 | ||
1014 | static int cris_dma_setup(ide_drive_t *drive) | |
1015 | { | |
1016 | struct request *rq = drive->hwif->hwgroup->rq; | |
1017 | ||
1018 | cris_ide_initialize_dma(!rq_data_dir(rq)); | |
1019 | if (cris_ide_build_dmatable (drive)) { | |
1020 | ide_map_sg(drive, rq); | |
1021 | return 1; | |
1022 | } | |
1023 | ||
1024 | drive->waiting_for_dma = 1; | |
1025 | return 0; | |
1026 | } | |
1027 | ||
1028 | static void cris_dma_exec_cmd(ide_drive_t *drive, u8 command) | |
1029 | { | |
1030 | /* set the irq handler which will finish the request when DMA is done */ | |
1031 | ide_set_handler(drive, &cris_dma_intr, WAIT_CMD, NULL); | |
1032 | ||
1033 | /* issue cmd to drive */ | |
1034 | cris_ide_outb(command, IDE_COMMAND_REG); | |
1035 | } | |
1036 | ||
1037 | static void cris_dma_start(ide_drive_t *drive) | |
1038 | { | |
1039 | struct request *rq = drive->hwif->hwgroup->rq; | |
1040 | int writing = rq_data_dir(rq); | |
1041 | int type = TYPE_DMA; | |
1042 | ||
1043 | if (drive->current_speed >= XFER_UDMA_0) | |
1044 | type = TYPE_UDMA; | |
1045 | ||
1046 | cris_ide_start_dma(drive, &ata_descrs[0], writing ? 0 : 1, type, ata_tot_size); | |
1047 | ||
1048 | if (writing) { | |
1049 | LED_DISK_WRITE(1); | |
1050 | } else { | |
1051 | LED_DISK_READ(1); | |
1052 | } | |
1053 | } |