Commit | Line | Data |
---|---|---|
ec8f24b7 | 1 | # SPDX-License-Identifier: GPL-2.0-only |
a9c5fff5 | 2 | # |
e849dc04 | 3 | # GPIO infrastructure and drivers |
a9c5fff5 DB |
4 | # |
5 | ||
7563bbf8 MB |
6 | config ARCH_HAVE_CUSTOM_GPIO_H |
7 | bool | |
8 | help | |
9 | Selecting this config option from the architecture Kconfig allows | |
10 | the architecture to provide a custom asm/gpio.h implementation | |
11 | overriding the default implementations. New uses of this are | |
12 | strongly discouraged. | |
13 | ||
7444a72e MB |
14 | menuconfig GPIOLIB |
15 | bool "GPIO Support" | |
7444a72e MB |
16 | help |
17 | This enables GPIO support through the generic GPIO library. | |
18 | You only need to enable this, if you also want to enable | |
e849dc04 | 19 | one or more of the GPIO drivers below. |
7444a72e MB |
20 | |
21 | If unsure, say N. | |
a9c5fff5 | 22 | |
7444a72e | 23 | if GPIOLIB |
a9c5fff5 | 24 | |
3027743f LA |
25 | config GPIOLIB_FASTPATH_LIMIT |
26 | int "Maximum number of GPIOs for fast path" | |
27 | range 32 512 | |
28 | default 512 | |
29 | help | |
c42e34c9 EWI |
30 | This adjusts the point at which certain APIs will switch from |
31 | using a stack allocated buffer to a dynamically allocated buffer. | |
3027743f | 32 | |
c42e34c9 EWI |
33 | You shouldn't need to change this unless you really need to |
34 | optimize either stack space or performance. Change this carefully | |
35 | since setting an incorrect value could cause stack corruption. | |
3027743f | 36 | |
f141ed65 GL |
37 | config OF_GPIO |
38 | def_bool y | |
92c74bce | 39 | depends on OF |
2527ecc9 | 40 | depends on HAS_IOMEM |
f141ed65 | 41 | |
e29482e8 MN |
42 | config GPIO_ACPI |
43 | def_bool y | |
44 | depends on ACPI | |
45 | ||
14250520 | 46 | config GPIOLIB_IRQCHIP |
fc346270 | 47 | select IRQ_DOMAIN |
14250520 LW |
48 | bool |
49 | ||
a9c5fff5 DB |
50 | config DEBUG_GPIO |
51 | bool "Debug GPIO calls" | |
52 | depends on DEBUG_KERNEL | |
53 | help | |
54 | Say Y here to add some extra checks and diagnostics to GPIO calls. | |
692105b8 ML |
55 | These checks help ensure that GPIOs have been properly initialized |
56 | before they are used, and that sleeping calls are not made from | |
57 | non-sleeping contexts. They can make bitbanged serial protocols | |
a9c5fff5 DB |
58 | slower. The diagnostics help catch the type of setup errors |
59 | that are most common when setting up new platforms or boards. | |
60 | ||
d8f388d8 | 61 | config GPIO_SYSFS |
3b4feb21 | 62 | bool "/sys/class/gpio/... (sysfs interface)" if EXPERT |
4c0ea233 | 63 | depends on SYSFS |
3b4feb21 | 64 | select GPIO_CDEV # We need to encourage the new ABI |
d8f388d8 | 65 | help |
db9477f8 | 66 | Say Y here to add the legacy sysfs interface for GPIOs. |
d8f388d8 | 67 | |
db9477f8 LW |
68 | This ABI is deprecated. If you want to use GPIO from userspace, |
69 | use the character device /dev/gpiochipN with the appropriate | |
d143493c KG |
70 | ioctl() operations instead. |
71 | ||
72 | config GPIO_CDEV | |
73 | bool | |
74 | prompt "Character device (/dev/gpiochipN) support" if EXPERT | |
75 | default y | |
76 | help | |
77 | Say Y here to add the character device /dev/gpiochipN interface | |
78 | for GPIOs. The character device allows userspace to control GPIOs | |
79 | using ioctl() operations. | |
80 | ||
81 | Only say N if you are sure that the GPIO character device is not | |
82 | required. | |
83 | ||
84 | If unsure, say Y. | |
d8f388d8 | 85 | |
957ebb61 KG |
86 | config GPIO_CDEV_V1 |
87 | bool "Support GPIO ABI Version 1" | |
88 | default y | |
89 | depends on GPIO_CDEV | |
90 | help | |
91 | Say Y here to support version 1 of the GPIO CDEV ABI. | |
92 | ||
93 | This ABI version is deprecated. | |
94 | Please use the latest ABI for new developments. | |
95 | ||
96 | If unsure, say Y. | |
97 | ||
c103de24 | 98 | config GPIO_GENERIC |
3085a4a4 | 99 | depends on HAS_IOMEM # Only for IOMEM drivers |
c103de24 GL |
100 | tristate |
101 | ||
ebe36319 MW |
102 | config GPIO_REGMAP |
103 | depends on REGMAP | |
104 | tristate | |
105 | ||
e849dc04 | 106 | # put drivers in the right section, in alphabetical order |
a9c5fff5 | 107 | |
177b0381 | 108 | # This symbol is selected by both I2C and SPI expanders |
e952805d WS |
109 | config GPIO_MAX730X |
110 | tristate | |
111 | ||
177b0381 | 112 | menu "Memory mapped GPIO drivers" |
3085a4a4 | 113 | depends on HAS_IOMEM |
0bcb6069 | 114 | |
af0a33e2 AS |
115 | config GPIO_74XX_MMIO |
116 | tristate "GPIO driver for 74xx-ICs with MMIO access" | |
117 | depends on OF_GPIO | |
118 | select GPIO_GENERIC | |
119 | help | |
120 | Say yes here to support GPIO functionality for 74xx-compatible ICs | |
121 | with MMIO access. Compatible models include: | |
122 | 1 bit: 741G125 (Input), 741G74 (Output) | |
123 | 2 bits: 742G125 (Input), 7474 (Output) | |
124 | 4 bits: 74125 (Input), 74175 (Output) | |
125 | 6 bits: 74365 (Input), 74174 (Output) | |
126 | 8 bits: 74244 (Input), 74273 (Output) | |
127 | 16 bits: 741624 (Input), 7416374 (Output) | |
128 | ||
223fa272 LW |
129 | config GPIO_ALTERA |
130 | tristate "Altera GPIO" | |
131 | depends on OF_GPIO | |
223fa272 LW |
132 | select GPIOLIB_IRQCHIP |
133 | help | |
134 | Say Y or M here to build support for the Altera PIO device. | |
135 | ||
136 | If driver is built as a module it will be called gpio-altera. | |
137 | ||
6057d40f YT |
138 | config GPIO_AMDPT |
139 | tristate "AMD Promontory GPIO support" | |
140 | depends on ACPI | |
574b782e | 141 | select GPIO_GENERIC |
6057d40f YT |
142 | help |
143 | driver for GPIO functionality on Promontory IOHub | |
144 | Require ACPI ASL code to enumerate as a platform device. | |
145 | ||
361b7911 JS |
146 | config GPIO_ASPEED |
147 | tristate "Aspeed GPIO support" | |
148 | depends on (ARCH_ASPEED || COMPILE_TEST) && OF_GPIO | |
149 | select GPIOLIB_IRQCHIP | |
150 | help | |
151 | Say Y here to support Aspeed AST2400 and AST2500 GPIO controllers. | |
152 | ||
f8b410e3 LW |
153 | config GPIO_ASPEED_SGPIO |
154 | bool "Aspeed SGPIO support" | |
155 | depends on (ARCH_ASPEED || COMPILE_TEST) && OF_GPIO | |
156 | select GPIO_GENERIC | |
157 | select GPIOLIB_IRQCHIP | |
158 | help | |
159 | Say Y here to support Aspeed AST2500 SGPIO functionality. | |
160 | ||
ab32770e AB |
161 | config GPIO_ATH79 |
162 | tristate "Atheros AR71XX/AR724X/AR913X GPIO support" | |
163 | default y if ATH79 | |
409d8783 | 164 | depends on ATH79 || COMPILE_TEST |
ab32770e | 165 | select GPIO_GENERIC |
2b8f89e1 | 166 | select GPIOLIB_IRQCHIP |
ab32770e AB |
167 | help |
168 | Select this option to enable GPIO driver for | |
169 | Atheros AR71XX/AR724X/AR913X SoC devices. | |
170 | ||
a98d90e7 DS |
171 | config GPIO_RASPBERRYPI_EXP |
172 | tristate "Raspberry Pi 3 GPIO Expander" | |
173 | default RASPBERRYPI_FIRMWARE | |
174 | depends on OF_GPIO | |
94337b72 BS |
175 | # Make sure not 'y' when RASPBERRYPI_FIRMWARE is 'm'. This can only |
176 | # happen when COMPILE_TEST=y, hence the added !RASPBERRYPI_FIRMWARE. | |
7ed91505 | 177 | depends on (ARCH_BCM2835 && RASPBERRYPI_FIRMWARE) || (COMPILE_TEST && !RASPBERRYPI_FIRMWARE) |
a98d90e7 DS |
178 | help |
179 | Turn on GPIO support for the expander on Raspberry Pi 3 boards, using | |
180 | the firmware mailbox to communicate with VideoCore on BCM283x chips. | |
181 | ||
ea948cff LW |
182 | config GPIO_BCM_KONA |
183 | bool "Broadcom Kona GPIO" | |
184 | depends on OF_GPIO && (ARCH_BCM_MOBILE || COMPILE_TEST) | |
185 | help | |
186 | Turn on GPIO support for Broadcom "Kona" chips. | |
187 | ||
6a41b6c5 CP |
188 | config GPIO_BCM_XGS_IPROC |
189 | tristate "BRCM XGS iProc GPIO support" | |
190 | depends on OF_GPIO && (ARCH_BCM_IPROC || COMPILE_TEST) | |
191 | select GPIO_GENERIC | |
192 | select GPIOLIB_IRQCHIP | |
193 | default ARCH_BCM_IPROC | |
194 | help | |
195 | Say yes here to enable GPIO support for Broadcom XGS iProc SoCs. | |
196 | ||
3b0213d5 GF |
197 | config GPIO_BRCMSTB |
198 | tristate "BRCMSTB GPIO support" | |
a02588a0 FF |
199 | default y if (ARCH_BRCMSTB || BMIPS_GENERIC) |
200 | depends on OF_GPIO && (ARCH_BRCMSTB || BMIPS_GENERIC || COMPILE_TEST) | |
3b0213d5 | 201 | select GPIO_GENERIC |
0ba31dc2 | 202 | select IRQ_DOMAIN |
3b0213d5 GF |
203 | help |
204 | Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs. | |
205 | ||
72ab2f76 JK |
206 | config GPIO_CADENCE |
207 | tristate "Cadence GPIO support" | |
208 | depends on OF_GPIO | |
209 | select GPIO_GENERIC | |
210 | select GPIOLIB_IRQCHIP | |
211 | help | |
212 | Say yes here to enable support for Cadence GPIO controller. | |
213 | ||
a3b8d4a5 | 214 | config GPIO_CLPS711X |
55fe14ab | 215 | tristate "CLPS711X GPIO support" |
ffd4bf1a | 216 | depends on ARCH_CLPS711X || COMPILE_TEST |
55fe14ab AS |
217 | select GPIO_GENERIC |
218 | help | |
219 | Say yes here to support GPIO on CLPS711X SoCs. | |
a3b8d4a5 | 220 | |
ee89cf63 GS |
221 | config GPIO_DAVINCI |
222 | bool "TI Davinci/Keystone GPIO support" | |
223 | default y if ARCH_DAVINCI | |
6eeea326 | 224 | depends on (ARM || ARM64) && (ARCH_DAVINCI || ARCH_KEYSTONE || ARCH_K3) |
ee89cf63 GS |
225 | help |
226 | Say yes here to enable GPIO support for TI Davinci/Keystone SoCs. | |
227 | ||
7779b345 JI |
228 | config GPIO_DWAPB |
229 | tristate "Synopsys DesignWare APB GPIO driver" | |
230 | select GPIO_GENERIC | |
0ea68393 | 231 | select GPIOLIB_IRQCHIP |
7779b345 JI |
232 | help |
233 | Say Y or M here to build support for the Synopsys DesignWare APB | |
234 | GPIO block. | |
235 | ||
25518e02 BW |
236 | config GPIO_EIC_SPRD |
237 | tristate "Spreadtrum EIC support" | |
238 | depends on ARCH_SPRD || COMPILE_TEST | |
239 | depends on OF_GPIO | |
240 | select GPIOLIB_IRQCHIP | |
241 | help | |
242 | Say yes here to support Spreadtrum EIC device. | |
243 | ||
a07e103e MD |
244 | config GPIO_EM |
245 | tristate "Emma Mobile GPIO" | |
22eaf13c | 246 | depends on (ARCH_EMEV2 || COMPILE_TEST) && OF_GPIO |
a07e103e MD |
247 | help |
248 | Say yes here to support GPIO on Renesas Emma Mobile SoCs. | |
249 | ||
c6b52c13 HS |
250 | config GPIO_EP93XX |
251 | def_bool y | |
252 | depends on ARCH_EP93XX | |
1e4c8842 | 253 | select GPIO_GENERIC |
a419a3d9 | 254 | select GPIOLIB_IRQCHIP |
c6b52c13 | 255 | |
6596e59e SM |
256 | config GPIO_EXAR |
257 | tristate "Support for GPIO pins on XR17V352/354/358" | |
258 | depends on SERIAL_8250_EXAR | |
36fb7218 | 259 | select REGMAP_MMIO |
6596e59e SM |
260 | help |
261 | Selecting this option will enable handling of GPIO pins present | |
262 | on Exar XR17V352/354/358 chips. | |
263 | ||
223fa272 LW |
264 | config GPIO_GE_FPGA |
265 | bool "GE FPGA based GPIO" | |
266 | depends on GE_FPGA | |
267 | select GPIO_GENERIC | |
268 | help | |
269 | Support for common GPIO functionality provided on some GE Single Board | |
270 | Computers. | |
271 | ||
272 | This driver provides basic support (configure as input or output, read | |
273 | and write pin state) for GPIO implemented in a number of GE single | |
274 | board computers. | |
275 | ||
9d3a15aa LW |
276 | config GPIO_FTGPIO010 |
277 | bool "Faraday FTGPIO010 GPIO" | |
49cec4d8 LW |
278 | depends on OF_GPIO |
279 | select GPIO_GENERIC | |
280 | select GPIOLIB_IRQCHIP | |
d8307c09 | 281 | default (ARCH_GEMINI || ARCH_MOXART) |
49cec4d8 | 282 | help |
9d3a15aa LW |
283 | Support for common GPIOs from the Faraday FTGPIO010 IP core, found in |
284 | Cortina systems Gemini platforms, Moxa ART and others. | |
49cec4d8 | 285 | |
223fa272 LW |
286 | config GPIO_GENERIC_PLATFORM |
287 | tristate "Generic memory-mapped GPIO controller support (MMIO platform device)" | |
288 | select GPIO_GENERIC | |
289 | help | |
290 | Say yes here to support basic platform_device memory-mapped GPIO controllers. | |
291 | ||
292 | config GPIO_GRGPIO | |
293 | tristate "Aeroflex Gaisler GRGPIO support" | |
048c28c9 | 294 | depends on OF_GPIO |
223fa272 LW |
295 | select GPIO_GENERIC |
296 | select IRQ_DOMAIN | |
297 | help | |
298 | Select this to support Aeroflex Gaisler GRGPIO cores from the GRLIB | |
299 | VHDL IP core library. | |
300 | ||
356b01a9 LJ |
301 | config GPIO_HISI |
302 | tristate "HiSilicon GPIO controller driver" | |
72db5d54 | 303 | depends on (ARM64 && ACPI) || COMPILE_TEST |
356b01a9 LJ |
304 | select GPIO_GENERIC |
305 | select GPIOLIB_IRQCHIP | |
306 | help | |
307 | Say Y or M here to build support for the HiSilicon GPIO controller | |
308 | driver GPIO block. | |
309 | This GPIO controller support double-edge interrupt and multi-core | |
310 | concurrent access. | |
311 | ||
8f55fed3 JN |
312 | config GPIO_HLWD |
313 | tristate "Nintendo Wii (Hollywood) GPIO" | |
314 | depends on OF_GPIO | |
315 | select GPIO_GENERIC | |
588de43c | 316 | select GPIOLIB_IRQCHIP |
8f55fed3 JN |
317 | help |
318 | Select this to support the GPIO controller of the Nintendo Wii. | |
319 | ||
320 | If unsure, say N. | |
321 | ||
223fa272 LW |
322 | config GPIO_ICH |
323 | tristate "Intel ICH GPIO" | |
324 | depends on PCI && X86 | |
325 | select MFD_CORE | |
326 | select LPC_ICH | |
327 | help | |
328 | Say yes here to support the GPIO functionality of a number of Intel | |
329 | ICH-based chipsets. Currently supported devices: ICH6, ICH7, ICH8 | |
330 | ICH9, ICH10, Series 5/3400 (eg Ibex Peak), Series 6/C200 (eg | |
331 | Cougar Point), NM10 (Tiger Point), and 3100 (Whitmore Lake). | |
332 | ||
333 | If unsure, say N. | |
334 | ||
335 | config GPIO_IOP | |
336 | tristate "Intel IOP GPIO" | |
59d3ae9a | 337 | depends on ARCH_IOP32X || COMPILE_TEST |
6d125412 | 338 | select GPIO_GENERIC |
223fa272 LW |
339 | help |
340 | Say yes here to support the GPIO functionality of a number of Intel | |
341 | IOP32X or IOP33X. | |
342 | ||
343 | If unsure, say N. | |
344 | ||
813e7d36 LW |
345 | config GPIO_IXP4XX |
346 | bool "Intel IXP4xx GPIO" | |
347 | depends on ARM # For <asm/mach-types.h> | |
348 | depends on ARCH_IXP4XX | |
349 | select GPIO_GENERIC | |
aa7d618a | 350 | select GPIOLIB_IRQCHIP |
813e7d36 LW |
351 | select IRQ_DOMAIN_HIERARCHY |
352 | help | |
353 | Say yes here to support the GPIO functionality of a number of Intel | |
354 | IXP4xx series of chips. | |
355 | ||
356 | If unsure, say N. | |
c16485ad PK |
357 | config GPIO_LOGICVC |
358 | tristate "Xylon LogiCVC GPIO support" | |
359 | depends on MFD_SYSCON && OF | |
360 | help | |
361 | Say yes here to support GPIO functionality of the Xylon LogiCVC | |
362 | programmable logic block. | |
813e7d36 | 363 | |
223fa272 LW |
364 | config GPIO_LOONGSON |
365 | bool "Loongson-2/3 GPIO support" | |
268a2d60 | 366 | depends on CPU_LOONGSON2EF || CPU_LOONGSON64 |
223fa272 LW |
367 | help |
368 | driver for GPIO functionality on Loongson-2F/3A/3B processors. | |
369 | ||
13a43fd9 | 370 | config GPIO_LPC18XX |
54b72998 | 371 | tristate "NXP LPC18XX/43XX GPIO support" |
13a43fd9 JE |
372 | default y if ARCH_LPC18XX |
373 | depends on OF_GPIO && (ARCH_LPC18XX || COMPILE_TEST) | |
5ddabfe8 | 374 | select IRQ_DOMAIN_HIERARCHY |
13a43fd9 JE |
375 | help |
376 | Select this option to enable GPIO driver for | |
377 | NXP LPC18XX/43XX devices. | |
378 | ||
f2ee7314 AB |
379 | config GPIO_LPC32XX |
380 | tristate "NXP LPC32XX GPIO support" | |
381 | depends on OF_GPIO && (ARCH_LPC32XX || COMPILE_TEST) | |
382 | help | |
383 | Select this option to enable GPIO driver for | |
384 | NXP LPC32XX devices. | |
385 | ||
0da094d8 | 386 | config GPIO_MB86S7X |
e1289dba | 387 | tristate "GPIO support for Fujitsu MB86S7x Platforms" |
0da094d8 JB |
388 | help |
389 | Say yes here to support the GPIO controller in Fujitsu MB86S70 SoCs. | |
390 | ||
f436bc27 AW |
391 | config GPIO_MENZ127 |
392 | tristate "MEN 16Z127 GPIO support" | |
393 | depends on MCB | |
394 | select GPIO_GENERIC | |
395 | help | |
c42e34c9 | 396 | Say yes here to support the MEN 16Z127 GPIO Controller |
f436bc27 | 397 | |
223fa272 LW |
398 | config GPIO_MM_LANTIQ |
399 | bool "Lantiq Memory mapped GPIOs" | |
400 | depends on LANTIQ && SOC_XWAY | |
401 | help | |
402 | This enables support for memory mapped GPIOs on the External Bus Unit | |
403 | (EBU) found on Lantiq SoCs. The gpios are output only as they are | |
404 | created by attaching a 16bit latch to the bus. | |
405 | ||
6eae1ace GL |
406 | config GPIO_MPC5200 |
407 | def_bool y | |
408 | depends on PPC_MPC52xx | |
409 | ||
c68308dd | 410 | config GPIO_MPC8XXX |
5df7fd46 | 411 | bool "MPC512x/MPC8xxx/QorIQ GPIO support" |
c68308dd | 412 | depends on PPC_MPC512x || PPC_MPC831x || PPC_MPC834x || PPC_MPC837x || \ |
5df7fd46 LG |
413 | FSL_SOC_BOOKE || PPC_86xx || ARCH_LAYERSCAPE || ARM || \ |
414 | COMPILE_TEST | |
415 | select GPIO_GENERIC | |
a8fa91a7 | 416 | select IRQ_DOMAIN |
c68308dd WS |
417 | help |
418 | Say Y here if you're going to use hardware that connects to the | |
5df7fd46 | 419 | MPC512x/831x/834x/837x/8572/8610/QorIQ GPIOs. |
c68308dd | 420 | |
4ba9c3af SP |
421 | config GPIO_MT7621 |
422 | bool "Mediatek MT7621 GPIO Support" | |
423 | depends on SOC_MT7620 || SOC_MT7621 || COMPILE_TEST | |
7a9a5df0 | 424 | depends on OF_GPIO |
4ba9c3af SP |
425 | select GPIO_GENERIC |
426 | select GPIOLIB_IRQCHIP | |
427 | help | |
428 | Say yes here to support the Mediatek MT7621 SoC GPIO device | |
429 | ||
fefe7b09 TP |
430 | config GPIO_MVEBU |
431 | def_bool y | |
3b4c94bb | 432 | depends on PLAT_ORION || ARCH_MVEBU |
048c28c9 | 433 | depends on OF_GPIO |
fefe7b09 | 434 | select GENERIC_IRQ_CHIP |
f37e335f | 435 | select REGMAP_MMIO |
fefe7b09 | 436 | |
d37a65bb | 437 | config GPIO_MXC |
12d16b39 | 438 | tristate "i.MX GPIO support" |
d4e93614 | 439 | depends on ARCH_MXC || COMPILE_TEST |
c103de24 | 440 | select GPIO_GENERIC |
e4ea9333 | 441 | select GENERIC_IRQ_CHIP |
c103de24 GL |
442 | |
443 | config GPIO_MXS | |
444 | def_bool y | |
6876ca31 | 445 | depends on ARCH_MXS || COMPILE_TEST |
06f88a8a | 446 | select GPIO_GENERIC |
498c17cf | 447 | select GENERIC_IRQ_CHIP |
d37a65bb | 448 | |
aca58a66 DD |
449 | config GPIO_OCTEON |
450 | tristate "Cavium OCTEON GPIO" | |
e4c6a52c | 451 | depends on CAVIUM_OCTEON_SOC |
aca58a66 DD |
452 | default y |
453 | help | |
454 | Say yes here to support the on-chip GPIO lines on the OCTEON | |
455 | family of SOCs. | |
456 | ||
cd0a3748 | 457 | config GPIO_OMAP |
cac089f9 | 458 | tristate "TI OMAP GPIO support" if ARCH_OMAP2PLUS || COMPILE_TEST |
cd0a3748 | 459 | default y if ARCH_OMAP |
9d5d96ef AB |
460 | depends on ARM |
461 | select GENERIC_IRQ_CHIP | |
fb655f57 | 462 | select GPIOLIB_IRQCHIP |
cd0a3748 JMC |
463 | help |
464 | Say yes here to enable GPIO support for TI OMAP SoCs. | |
465 | ||
1e9c2859 | 466 | config GPIO_PL061 |
61684440 | 467 | tristate "PrimeCell PL061 GPIO support" |
8a242842 | 468 | depends on ARM_AMBA |
a5d6d271 | 469 | select IRQ_DOMAIN |
8d5b24bd | 470 | select GPIOLIB_IRQCHIP |
1e9c2859 BS |
471 | help |
472 | Say yes here to support the PrimeCell PL061 GPIO device | |
473 | ||
348f3cde BW |
474 | config GPIO_PMIC_EIC_SPRD |
475 | tristate "Spreadtrum PMIC EIC support" | |
476 | depends on MFD_SC27XX_PMIC || COMPILE_TEST | |
477 | depends on OF_GPIO | |
478 | select GPIOLIB_IRQCHIP | |
479 | help | |
480 | Say yes here to support Spreadtrum PMIC EIC device. | |
481 | ||
157d2644 HZ |
482 | config GPIO_PXA |
483 | bool "PXA GPIO support" | |
22e4ebd0 | 484 | depends on ARCH_PXA || ARCH_MMP || COMPILE_TEST |
157d2644 HZ |
485 | help |
486 | Say yes here to support the PXA GPIO device | |
487 | ||
119f5e44 MD |
488 | config GPIO_RCAR |
489 | tristate "Renesas R-Car GPIO" | |
2af66e1d | 490 | depends on ARCH_RENESAS || COMPILE_TEST |
c7f3c5d3 | 491 | select GPIOLIB_IRQCHIP |
119f5e44 MD |
492 | help |
493 | Say yes here to support GPIO on Renesas R-Car SoCs. | |
494 | ||
d57eb825 MS |
495 | config GPIO_RDA |
496 | bool "RDA Micro GPIO controller support" | |
497 | depends on ARCH_RDA || COMPILE_TEST | |
498 | depends on OF_GPIO | |
499 | select GPIO_GENERIC | |
500 | select GPIOLIB_IRQCHIP | |
501 | help | |
502 | Say Y here to support RDA Micro GPIO controller. | |
503 | ||
380639c7 RK |
504 | config GPIO_REG |
505 | bool | |
506 | help | |
507 | A 32-bit single register GPIO fixed in/out implementation. This | |
508 | can be used to represent any register as a set of GPIO signals. | |
509 | ||
fb0b35d3 AS |
510 | config GPIO_SAMA5D2_PIOBU |
511 | tristate "SAMA5D2 PIOBU GPIO support" | |
512 | depends on MFD_SYSCON | |
a7c23f8d | 513 | depends on OF_GPIO |
fb0b35d3 AS |
514 | select GPIO_SYSCON |
515 | help | |
516 | Say yes here to use the PIOBU pins as GPIOs. | |
517 | ||
518 | PIOBU pins on the SAMA5D2 can be used as GPIOs. | |
519 | The difference from regular GPIOs is that they | |
520 | maintain their value during backup/self-refresh. | |
521 | ||
96868dce YS |
522 | config GPIO_SIFIVE |
523 | bool "SiFive GPIO support" | |
524 | depends on OF_GPIO && IRQ_DOMAIN_HIERARCHY | |
525 | select GPIO_GENERIC | |
526 | select GPIOLIB_IRQCHIP | |
527 | select REGMAP_MMIO | |
528 | help | |
529 | Say yes here to support the GPIO device on SiFive SoCs. | |
530 | ||
be8c8fac UKK |
531 | config GPIO_SIOX |
532 | tristate "SIOX GPIO support" | |
533 | depends on SIOX | |
534 | select GPIOLIB_IRQCHIP | |
535 | help | |
536 | Say yes here to support SIOX I/O devices. These are units connected | |
537 | via a SIOX bus and have a number of fixed-direction I/O lines. | |
538 | ||
2505c7b0 EP |
539 | config GPIO_SNPS_CREG |
540 | bool "Synopsys GPIO via CREG (Control REGisters) driver" | |
541 | depends on ARC || COMPILE_TEST | |
a7c0b4b8 | 542 | depends on OF_GPIO |
2505c7b0 EP |
543 | help |
544 | This driver supports GPIOs via CREG on various Synopsys SoCs. | |
545 | This is a single-register MMIO GPIO driver for complex cases | |
546 | where only several fields in register belong to GPIO lines and | |
547 | each GPIO line owns a field with different length and on/off value. | |
548 | ||
b53bc281 SH |
549 | config GPIO_SPEAR_SPICS |
550 | bool "ST SPEAr13xx SPI Chip Select as GPIO support" | |
551 | depends on PLAT_SPEAR | |
552 | select GENERIC_IRQ_CHIP | |
553 | help | |
554 | Say yes here to support ST SPEAr SPI Chip Select as GPIO device | |
555 | ||
9a3821c2 BW |
556 | config GPIO_SPRD |
557 | tristate "Spreadtrum GPIO support" | |
558 | depends on ARCH_SPRD || COMPILE_TEST | |
559 | depends on OF_GPIO | |
560 | select GPIOLIB_IRQCHIP | |
561 | help | |
562 | Say yes here to support Spreadtrum GPIO device. | |
563 | ||
7b0d44f3 AR |
564 | config GPIO_STA2X11 |
565 | bool "STA2x11/ConneXt GPIO support" | |
566 | depends on MFD_STA2X11 | |
567 | select GENERIC_IRQ_CHIP | |
568 | help | |
569 | Say yes here to support the STA2x11/ConneXt GPIO device. | |
570 | The GPIO module has 128 GPIO pins with alternate functions. | |
571 | ||
be9cab5b LW |
572 | config GPIO_STP_XWAY |
573 | bool "XWAY STP GPIOs" | |
5099837d MB |
574 | depends on SOC_XWAY || COMPILE_TEST |
575 | depends on OF_GPIO | |
be9cab5b LW |
576 | help |
577 | This enables support for the Serial To Parallel (STP) unit found on | |
578 | XWAY SoC. The STP allows the SoC to drive a shift registers cascade, | |
579 | that can be up to 24 bit. This peripheral is aimed at driving leds. | |
580 | Some of the gpios/leds can be auto updated by the soc with dsl and | |
581 | phy status. | |
582 | ||
6a8a0c1d AS |
583 | config GPIO_SYSCON |
584 | tristate "GPIO based on SYSCON" | |
585 | depends on MFD_SYSCON && OF | |
586 | help | |
587 | Say yes here to support GPIO functionality though SYSCON driver. | |
588 | ||
223fa272 LW |
589 | config GPIO_TB10X |
590 | bool | |
0d1e31ab | 591 | select GPIO_GENERIC |
223fa272 LW |
592 | select GENERIC_IRQ_CHIP |
593 | select OF_GPIO | |
594 | ||
4dd4dd1d | 595 | config GPIO_TEGRA |
0bfb85c6 AB |
596 | bool "NVIDIA Tegra GPIO support" |
597 | default ARCH_TEGRA | |
4dd4dd1d | 598 | depends on ARCH_TEGRA || COMPILE_TEST |
048c28c9 | 599 | depends on OF_GPIO |
0bfb85c6 AB |
600 | help |
601 | Say yes here to support GPIO pins on NVIDIA Tegra SoCs. | |
4dd4dd1d | 602 | |
5b2b135a TR |
603 | config GPIO_TEGRA186 |
604 | tristate "NVIDIA Tegra186 GPIO support" | |
286e7bea TR |
605 | default ARCH_TEGRA_186_SOC || ARCH_TEGRA_194_SOC |
606 | depends on ARCH_TEGRA_186_SOC || ARCH_TEGRA_194_SOC || COMPILE_TEST | |
5b2b135a TR |
607 | depends on OF_GPIO |
608 | select GPIOLIB_IRQCHIP | |
2a365505 | 609 | select IRQ_DOMAIN_HIERARCHY |
5b2b135a TR |
610 | help |
611 | Say yes here to support GPIO pins on NVIDIA Tegra186 SoCs. | |
612 | ||
5041e791 JG |
613 | config GPIO_TS4800 |
614 | tristate "TS-4800 DIO blocks and compatibles" | |
615 | depends on OF_GPIO | |
6dcfd729 | 616 | depends on SOC_IMX51 || COMPILE_TEST |
5041e791 JG |
617 | select GPIO_GENERIC |
618 | help | |
619 | This driver support TS-4800 FPGA GPIO controllers. | |
620 | ||
5a2a3002 DD |
621 | config GPIO_THUNDERX |
622 | tristate "Cavium ThunderX/OCTEON-TX GPIO" | |
623 | depends on ARCH_THUNDER || (64BIT && COMPILE_TEST) | |
311de3ce | 624 | depends on PCI_MSI |
a7fc89f9 | 625 | select GPIOLIB_IRQCHIP |
311de3ce | 626 | select IRQ_DOMAIN_HIERARCHY |
5a2a3002 DD |
627 | select IRQ_FASTEOI_HIERARCHY_HANDLERS |
628 | help | |
629 | Say yes here to support the on-chip GPIO lines on the ThunderX | |
630 | and OCTEON-TX families of SoCs. | |
631 | ||
dbe776c2 MY |
632 | config GPIO_UNIPHIER |
633 | tristate "UniPhier GPIO support" | |
634 | depends on ARCH_UNIPHIER || COMPILE_TEST | |
635 | depends on OF_GPIO | |
636 | select IRQ_DOMAIN_HIERARCHY | |
637 | help | |
638 | Say yes here to support UniPhier GPIOs. | |
639 | ||
7f2691a1 SA |
640 | config GPIO_VF610 |
641 | def_bool y | |
642 | depends on ARCH_MXC && SOC_VF610 | |
643 | select GPIOLIB_IRQCHIP | |
644 | help | |
645 | Say yes here to support Vybrid vf610 GPIOs. | |
646 | ||
223fa272 LW |
647 | config GPIO_VR41XX |
648 | tristate "NEC VR4100 series General-purpose I/O Uint support" | |
649 | depends on CPU_VR41XX | |
650 | help | |
651 | Say yes here to support the NEC VR4100 series General-purpose I/O Uint | |
652 | ||
653 | config GPIO_VX855 | |
654 | tristate "VIA VX855/VX875 GPIO" | |
72aba2e2 | 655 | depends on (X86 || COMPILE_TEST) && PCI |
223fa272 LW |
656 | select MFD_CORE |
657 | select MFD_VX855 | |
658 | help | |
659 | Support access to the VX855/VX875 GPIO lines through the gpio library. | |
660 | ||
661 | This driver provides common support for accessing the device, | |
662 | additional drivers must be enabled in order to use the | |
663 | functionality of the device. | |
664 | ||
59c32468 SK |
665 | config GPIO_WCD934X |
666 | tristate "Qualcomm Technologies Inc WCD9340/WCD9341 gpio controller driver" | |
667 | depends on MFD_WCD934X && OF_GPIO | |
668 | help | |
669 | This driver is to supprot GPIO block found on the Qualcomm Technologies | |
670 | Inc WCD9340/WCD9341 Audio Codec. | |
671 | ||
29cbf458 FK |
672 | config GPIO_XGENE |
673 | bool "APM X-Gene GPIO controller support" | |
674 | depends on ARM64 && OF_GPIO | |
675 | help | |
676 | This driver is to support the GPIO block within the APM X-Gene SoC | |
677 | platform's generic flash controller. The GPIO pins are muxed with | |
678 | the generic flash controller's address and data pins. Say yes | |
679 | here to enable the GFC GPIO functionality. | |
680 | ||
b2b35e10 V |
681 | config GPIO_XGENE_SB |
682 | tristate "APM X-Gene GPIO standby controller support" | |
b24bc583 | 683 | depends on (ARCH_XGENE || COMPILE_TEST) |
b2b35e10 | 684 | select GPIO_GENERIC |
e5f7e312 | 685 | select GPIOLIB_IRQCHIP |
c23d200f | 686 | select IRQ_DOMAIN_HIERARCHY |
b2b35e10 V |
687 | help |
688 | This driver supports the GPIO block within the APM X-Gene | |
689 | Standby Domain. Say yes here to enable the GPIO functionality. | |
690 | ||
0bcb6069 | 691 | config GPIO_XILINX |
c54c58ba | 692 | tristate "Xilinx GPIO support" |
0bcb6069 JL |
693 | help |
694 | Say yes here to support the Xilinx FPGA GPIO device | |
695 | ||
ff718800 KP |
696 | config GPIO_XLP |
697 | tristate "Netlogic XLP GPIO support" | |
240d3d5b | 698 | depends on OF_GPIO && (CPU_XLP || ARCH_THUNDER2 || COMPILE_TEST) |
ff718800 KP |
699 | select GPIOLIB_IRQCHIP |
700 | help | |
701 | This driver provides support for GPIO interface on Netlogic XLP MIPS64 | |
702 | SoCs. Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, | |
240d3d5b J |
703 | XLP9XX and XLP5XX. The same GPIO controller block is also present in |
704 | Cavium's ThunderX2 CN99XX SoCs. | |
ff718800 KP |
705 | |
706 | If unsure, say N. | |
707 | ||
3b31d0ec BS |
708 | config GPIO_XTENSA |
709 | bool "Xtensa GPIO32 support" | |
710 | depends on XTENSA | |
a1a2bdec | 711 | depends on HAVE_XTENSA_GPIO32 |
3b31d0ec BS |
712 | depends on !SMP |
713 | help | |
714 | Say yes here to support the Xtensa internal GPIO32 IMPWIRE (input) | |
715 | and EXPSTATE (output) ports | |
716 | ||
223fa272 LW |
717 | config GPIO_ZEVIO |
718 | bool "LSI ZEVIO SoC memory mapped GPIOs" | |
719 | depends on ARM && OF_GPIO | |
27fdd325 | 720 | help |
223fa272 | 721 | Say yes here to support the GPIO controller in LSI ZEVIO SoCs. |
27fdd325 | 722 | |
223fa272 LW |
723 | config GPIO_ZYNQ |
724 | tristate "Xilinx Zynq GPIO support" | |
bdf7a4ae | 725 | depends on ARCH_ZYNQ || ARCH_ZYNQMP |
7f87210e | 726 | select GPIOLIB_IRQCHIP |
be9b06b2 | 727 | help |
223fa272 | 728 | Say yes here to support Xilinx Zynq GPIO controller. |
92021490 | 729 | |
0963670a LW |
730 | config GPIO_ZX |
731 | bool "ZTE ZX GPIO support" | |
752fda89 | 732 | depends on ARCH_ZX || COMPILE_TEST |
0963670a LW |
733 | select GPIOLIB_IRQCHIP |
734 | help | |
735 | Say yes here to support the GPIO device on ZTE ZX SoCs. | |
736 | ||
bd37c999 KC |
737 | config GPIO_LOONGSON1 |
738 | tristate "Loongson1 GPIO support" | |
739 | depends on MACH_LOONGSON32 | |
740 | select GPIO_GENERIC | |
741 | help | |
742 | Say Y or M here to support GPIO on Loongson1 SoCs. | |
743 | ||
e09d168f EWI |
744 | config GPIO_AMD_FCH |
745 | tristate "GPIO support for AMD Fusion Controller Hub (G-series SOCs)" | |
746 | help | |
747 | This option enables driver for GPIO on AMDs Fusion Controller Hub, | |
748 | as found on G-series SOCs (eg. GX-412TC) | |
749 | ||
750 | Note: This driver doesn't registers itself automatically, as it | |
751 | needs to be provided with platform specific configuration. | |
752 | (See eg. CONFIG_PCENGINES_APU2.) | |
93224edf DP |
753 | |
754 | config GPIO_MSC313 | |
755 | bool "MStar MSC313 GPIO support" | |
756 | depends on ARCH_MSTARV7 | |
757 | default ARCH_MSTARV7 | |
758 | select GPIOLIB_IRQCHIP | |
759 | select IRQ_DOMAIN_HIERARCHY | |
760 | help | |
761 | Say Y here to support the main GPIO block on MStar/SigmaStar | |
762 | ARMv7 based SoCs. | |
763 | ||
177b0381 | 764 | endmenu |
be9b06b2 | 765 | |
bc6a73bb | 766 | menu "Port-mapped I/O GPIO drivers" |
7768feb0 | 767 | depends on X86 # Unconditional I/O space access |
bc6a73bb | 768 | |
1b06d64f WBG |
769 | config GPIO_104_DIO_48E |
770 | tristate "ACCES 104-DIO-48E GPIO support" | |
35decc80 WBG |
771 | depends on PC104 |
772 | select ISA_BUS_API | |
1b06d64f WBG |
773 | select GPIOLIB_IRQCHIP |
774 | help | |
4c23db0f WBG |
775 | Enables GPIO support for the ACCES 104-DIO-48E series (104-DIO-48E, |
776 | 104-DIO-24E). The base port addresses for the devices may be | |
777 | configured via the base module parameter. The interrupt line numbers | |
778 | for the devices may be configured via the irq module parameter. | |
1b06d64f | 779 | |
bc6a73bb LW |
780 | config GPIO_104_IDIO_16 |
781 | tristate "ACCES 104-IDIO-16 GPIO support" | |
35decc80 WBG |
782 | depends on PC104 |
783 | select ISA_BUS_API | |
a1184147 | 784 | select GPIOLIB_IRQCHIP |
bc6a73bb | 785 | help |
86ea8a95 WBG |
786 | Enables GPIO support for the ACCES 104-IDIO-16 family (104-IDIO-16, |
787 | 104-IDIO-16E, 104-IDO-16, 104-IDIO-8, 104-IDIO-8E, 104-IDO-8). The | |
788 | base port addresses for the devices may be configured via the base | |
789 | module parameter. The interrupt line numbers for the devices may be | |
790 | configured via the irq module parameter. | |
bc6a73bb | 791 | |
6ddcf9b4 WBG |
792 | config GPIO_104_IDI_48 |
793 | tristate "ACCES 104-IDI-48 GPIO support" | |
35decc80 WBG |
794 | depends on PC104 |
795 | select ISA_BUS_API | |
6ddcf9b4 WBG |
796 | select GPIOLIB_IRQCHIP |
797 | help | |
72bf7443 WBG |
798 | Enables GPIO support for the ACCES 104-IDI-48 family (104-IDI-48A, |
799 | 104-IDI-48AC, 104-IDI-48B, 104-IDI-48BC). The base port addresses for | |
800 | the devices may be configured via the base module parameter. The | |
801 | interrupt line numbers for the devices may be configured via the irq | |
802 | module parameter. | |
6ddcf9b4 | 803 | |
bc6a73bb | 804 | config GPIO_F7188X |
1920906f | 805 | tristate "F71869, F71869A, F71882FG, F71889F and F81866 GPIO support" |
bc6a73bb LW |
806 | help |
807 | This option enables support for GPIOs found on Fintek Super-I/O | |
1920906f | 808 | chips F71869, F71869A, F71882FG, F71889F and F81866. |
bc6a73bb LW |
809 | |
810 | To compile this driver as a module, choose M here: the module will | |
811 | be called f7188x-gpio. | |
812 | ||
6ea5dcdf WBG |
813 | config GPIO_GPIO_MM |
814 | tristate "Diamond Systems GPIO-MM GPIO support" | |
35decc80 WBG |
815 | depends on PC104 |
816 | select ISA_BUS_API | |
6ea5dcdf WBG |
817 | help |
818 | Enables GPIO support for the Diamond Systems GPIO-MM and GPIO-MM-12. | |
819 | ||
820 | The Diamond Systems GPIO-MM device features 48 lines of digital I/O | |
821 | via the emulation of dual 82C55A PPI chips. This driver provides GPIO | |
822 | support for these 48 channels of digital I/O. | |
823 | ||
824 | The base port addresses for the devices may be configured via the base | |
825 | array module parameter. | |
826 | ||
bc6a73bb LW |
827 | config GPIO_IT87 |
828 | tristate "IT87xx GPIO support" | |
bc6a73bb LW |
829 | help |
830 | Say yes here to support GPIO functionality of IT87xx Super I/O chips. | |
831 | ||
832 | This driver is tested with ITE IT8728 and IT8732 Super I/O chips, and | |
a5ec96dd LB |
833 | supports the IT8761E, IT8613, IT8620E, and IT8628E Super I/O chips as |
834 | well. | |
bc6a73bb LW |
835 | |
836 | To compile this driver as a module, choose M here: the module will | |
837 | be called gpio_it87 | |
838 | ||
839 | config GPIO_SCH | |
840 | tristate "Intel SCH/TunnelCreek/Centerton/Quark X1000 GPIO" | |
72aba2e2 | 841 | depends on (X86 || COMPILE_TEST) && PCI |
bc6a73bb LW |
842 | select MFD_CORE |
843 | select LPC_SCH | |
844 | help | |
845 | Say yes here to support GPIO interface on Intel Poulsbo SCH, | |
846 | Intel Tunnel Creek processor, Intel Centerton processor or | |
847 | Intel Quark X1000 SoC. | |
848 | ||
849 | The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are | |
850 | powered by the core power rail and are turned off during sleep | |
851 | modes (S3 and higher). The remaining four GPIOs are powered by | |
852 | the Intel SCH suspend power supply. These GPIOs remain | |
853 | active during S3. The suspend powered GPIOs can be used to wake the | |
854 | system from the Suspend-to-RAM state. | |
855 | ||
856 | The Intel Tunnel Creek processor has 5 GPIOs powered by the | |
857 | core power rail and 9 from suspend power supply. | |
858 | ||
859 | The Intel Centerton processor has a total of 30 GPIO pins. | |
860 | Twenty-one are powered by the core power rail and 9 from the | |
861 | suspend power supply. | |
862 | ||
863 | The Intel Quark X1000 SoC has 2 GPIOs powered by the core | |
864 | power well and 6 from the suspend power well. | |
865 | ||
866 | config GPIO_SCH311X | |
867 | tristate "SMSC SCH311x SuperI/O GPIO" | |
868 | help | |
869 | Driver to enable the GPIOs found on SMSC SMSC SCH3112, SCH3114 and | |
870 | SCH3116 "Super I/O" chipsets. | |
871 | ||
872 | To compile this driver as a module, choose M here: the module will | |
873 | be called gpio-sch311x. | |
874 | ||
875 | config GPIO_TS5500 | |
876 | tristate "TS-5500 DIO blocks and compatibles" | |
877 | depends on TS5500 || COMPILE_TEST | |
878 | help | |
879 | This driver supports Digital I/O exposed by pin blocks found on some | |
880 | Technologic Systems platforms. It includes, but is not limited to, 3 | |
881 | blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600 | |
882 | LCD port. | |
883 | ||
a0d65009 MS |
884 | config GPIO_WINBOND |
885 | tristate "Winbond Super I/O GPIO support" | |
b995ff3b | 886 | select ISA_BUS_API |
a0d65009 MS |
887 | help |
888 | This option enables support for GPIOs found on Winbond Super I/O | |
889 | chips. | |
890 | Currently, only W83627UHG (also known as Nuvoton NCT6627UD) is | |
891 | supported. | |
892 | ||
893 | You will need to provide a module parameter "gpios", or a | |
894 | boot-time parameter "gpio_winbond.gpios" with a bitmask of GPIO | |
895 | ports to enable (bit 0 is GPIO1, bit 1 is GPIO2, etc.). | |
896 | ||
897 | To compile this driver as a module, choose M here: the module will | |
898 | be called gpio-winbond. | |
899 | ||
9c26df9b WBG |
900 | config GPIO_WS16C48 |
901 | tristate "WinSystems WS16C48 GPIO support" | |
35decc80 | 902 | select ISA_BUS_API |
9c26df9b WBG |
903 | select GPIOLIB_IRQCHIP |
904 | help | |
cc736607 WBG |
905 | Enables GPIO support for the WinSystems WS16C48. The base port |
906 | addresses for the devices may be configured via the base module | |
907 | parameter. The interrupt line numbers for the devices may be | |
908 | configured via the irq module parameter. | |
9c26df9b | 909 | |
bc6a73bb LW |
910 | endmenu |
911 | ||
177b0381 LW |
912 | menu "I2C GPIO expanders" |
913 | depends on I2C | |
92021490 | 914 | |
bf5a16ba LW |
915 | config GPIO_ADP5588 |
916 | tristate "ADP5588 I2C GPIO expander" | |
6ed9f9c4 | 917 | help |
bf5a16ba LW |
918 | This option enables support for 18 GPIOs found |
919 | on Analog Devices ADP5588 GPIO Expanders. | |
be9b06b2 | 920 | |
bf5a16ba LW |
921 | config GPIO_ADP5588_IRQ |
922 | bool "Interrupt controller support for ADP5588" | |
923 | depends on GPIO_ADP5588=y | |
e9646f0f | 924 | select GPIOLIB_IRQCHIP |
e9004f50 | 925 | help |
bf5a16ba LW |
926 | Say yes here to enable the adp5588 to be used as an interrupt |
927 | controller. It requires the driver to be built in the kernel. | |
31ba56f2 | 928 | |
bf5a16ba LW |
929 | config GPIO_ADNP |
930 | tristate "Avionic Design N-bit GPIO expander" | |
269a46f8 | 931 | depends on OF_GPIO |
104fb1d5 ZL |
932 | select GPIOLIB_IRQCHIP |
933 | help | |
bf5a16ba LW |
934 | This option enables support for N GPIOs found on Avionic Design |
935 | I2C GPIO expanders. The register space will be extended by powers | |
936 | of two, so the controller will need to accommodate for that. For | |
937 | example: if a controller provides 48 pins, 6 registers will be | |
938 | enough to represent all pins, but the driver will assume a | |
939 | register layout for 64 pins (8 registers). | |
0cc59b9d | 940 | |
2a0b0a57 LW |
941 | config GPIO_GW_PLD |
942 | tristate "Gateworks PLD GPIO Expander" | |
943 | depends on OF_GPIO | |
944 | help | |
945 | Say yes here to provide access to the Gateworks I2C PLD GPIO | |
946 | Expander. This is used at least on the Cambria GW2358-4. | |
947 | ||
e952805d WS |
948 | config GPIO_MAX7300 |
949 | tristate "Maxim MAX7300 GPIO expander" | |
e952805d WS |
950 | select GPIO_MAX730X |
951 | help | |
2b861f4b | 952 | GPIO driver for Maxim MAX7300 I2C-based GPIO expander. |
e952805d | 953 | |
bbcd6d54 EM |
954 | config GPIO_MAX732X |
955 | tristate "MAX7319, MAX7320-7327 I2C Port Expanders" | |
bbcd6d54 EM |
956 | help |
957 | Say yes here to support the MAX7319, MAX7320-7327 series of I2C | |
958 | Port Expanders. Each IO port on these chips has a fixed role of | |
959 | Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain | |
960 | Input and Output (designed by 'P'). The combinations are listed | |
961 | below: | |
962 | ||
c42e34c9 EWI |
963 | 8 bits: max7319 (8I), max7320 (8O), max7321 (8P), |
964 | max7322 (4I4O), max7323 (4P4O) | |
bbcd6d54 | 965 | |
c42e34c9 EWI |
966 | 16 bits: max7324 (8I8O), max7325 (8P8O), |
967 | max7326 (4I12O), max7327 (4P12O) | |
bbcd6d54 EM |
968 | |
969 | Board setup code must specify the model to use, and the start | |
970 | number for these GPIOs. | |
971 | ||
a80a0bbe MZ |
972 | config GPIO_MAX732X_IRQ |
973 | bool "Interrupt controller support for MAX732x" | |
0244ad00 | 974 | depends on GPIO_MAX732X=y |
984f6643 | 975 | select GPIOLIB_IRQCHIP |
a80a0bbe MZ |
976 | help |
977 | Say yes here to enable the max732x to be used as an interrupt | |
978 | controller. It requires the driver to be built in the kernel. | |
979 | ||
608589b1 | 980 | config GPIO_MC9S08DZ60 |
981 | bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions" | |
4c30aa33 | 982 | depends on I2C=y && MACH_MX35_3DS |
608589b1 | 983 | help |
984 | Select this to enable the MC9S08DZ60 GPIO driver | |
985 | ||
f3dc3630 | 986 | config GPIO_PCA953X |
eb32b5aa | 987 | tristate "PCA95[357]x, PCA9698, TCA64xx, and MAX7310 I/O ports" |
4bc16f9d | 988 | select REGMAP_I2C |
9e60fdcf | 989 | help |
7059d4b0 DB |
990 | Say yes here to provide access to several register-oriented |
991 | SMBus I/O expanders, made mostly by NXP or TI. Compatible | |
992 | models include: | |
993 | ||
c42e34c9 | 994 | 4 bits: pca9536, pca9537 |
7059d4b0 | 995 | |
c42e34c9 EWI |
996 | 8 bits: max7310, max7315, pca6107, pca9534, pca9538, pca9554, |
997 | pca9556, pca9557, pca9574, tca6408, tca9554, xra1202 | |
7059d4b0 | 998 | |
c42e34c9 EWI |
999 | 16 bits: max7312, max7313, pca9535, pca9539, pca9555, pca9575, |
1000 | tca6416 | |
9e60fdcf | 1001 | |
c42e34c9 | 1002 | 24 bits: tca6424 |
1e191695 | 1003 | |
c42e34c9 | 1004 | 40 bits: pca9505, pca9698 |
1e191695 | 1005 | |
89ea8bbe MZ |
1006 | config GPIO_PCA953X_IRQ |
1007 | bool "Interrupt controller support for PCA953x" | |
e33a58a2 | 1008 | depends on GPIO_PCA953X |
7bcbce55 | 1009 | select GPIOLIB_IRQCHIP |
89ea8bbe MZ |
1010 | help |
1011 | Say yes here to enable the pca953x to be used as an interrupt | |
1012 | controller. It requires the driver to be built in the kernel. | |
1013 | ||
16d44b60 SE |
1014 | config GPIO_PCA9570 |
1015 | tristate "PCA9570 4-Bit I2C GPO expander" | |
1016 | help | |
1017 | Say yes here to enable the GPO driver for the NXP PCA9570 chip. | |
1018 | ||
1019 | To compile this driver as a module, choose M here: the module will | |
1020 | be called gpio-pca9570. | |
1021 | ||
15fae37d | 1022 | config GPIO_PCF857X |
1673ad52 | 1023 | tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders" |
a39294bd | 1024 | select GPIOLIB_IRQCHIP |
901acf5b | 1025 | select IRQ_DOMAIN |
15fae37d DB |
1026 | help |
1027 | Say yes here to provide access to most "quasi-bidirectional" I2C | |
1028 | GPIO expanders used for additional digital outputs or inputs. | |
1029 | Most of these parts are from NXP, though TI is a second source for | |
1030 | some of them. Compatible models include: | |
1031 | ||
1032 | 8 bits: pcf8574, pcf8574a, pca8574, pca8574a, | |
1673ad52 | 1033 | pca9670, pca9672, pca9674, pca9674a, |
c42e34c9 | 1034 | max7328, max7329 |
15fae37d DB |
1035 | |
1036 | 16 bits: pcf8575, pcf8575c, pca8575, | |
1037 | pca9671, pca9673, pca9675 | |
1038 | ||
1039 | Your board setup code will need to declare the expanders in | |
1040 | use, and assign numbers to the GPIOs they expose. Those GPIOs | |
1041 | can then be used from drivers and other kernel code, just like | |
1042 | other GPIOs, but only accessible from task contexts. | |
1043 | ||
1044 | This driver provides an in-kernel interface to those GPIOs using | |
1045 | platform-neutral GPIO calls. | |
1046 | ||
b866526d AD |
1047 | config GPIO_TPIC2810 |
1048 | tristate "TPIC2810 8-Bit I2C GPO expander" | |
1049 | help | |
1050 | Say yes here to enable the GPO driver for the TI TPIC2810 chip. | |
1051 | ||
1052 | To compile this driver as a module, choose M here: the module will | |
1053 | be called gpio-tpic2810. | |
1054 | ||
9c668632 LQ |
1055 | config GPIO_TS4900 |
1056 | tristate "Technologic Systems FPGA I2C GPIO" | |
4c5f15b7 | 1057 | depends on SOC_IMX6 || COMPILE_TEST |
9c668632 LQ |
1058 | select REGMAP_I2C |
1059 | help | |
1060 | Say yes here to enabled the GPIO driver for Technologic's FPGA core. | |
1061 | Series supported include TS-4100, TS-4900, TS-7970 and TS-7990. | |
1062 | ||
177b0381 LW |
1063 | endmenu |
1064 | ||
1065 | menu "MFD GPIO expanders" | |
be9cab5b LW |
1066 | |
1067 | config GPIO_ADP5520 | |
1068 | tristate "GPIO Support for ADP5520 PMIC" | |
1069 | depends on PMIC_ADP5520 | |
1070 | help | |
1071 | This option enables support for on-chip GPIO found | |
1072 | on Analog Devices ADP5520 PMICs. | |
1073 | ||
26a48c4c TT |
1074 | config GPIO_ALTERA_A10SR |
1075 | tristate "Altera Arria10 System Resource GPIO" | |
1076 | depends on MFD_ALTERA_A10SR | |
1077 | help | |
1078 | Driver for Arria10 Development Kit GPIO expansion which | |
1079 | includes reads of pushbuttons and DIP switches as well | |
1080 | as writes to LEDs. | |
1081 | ||
be9cab5b LW |
1082 | config GPIO_ARIZONA |
1083 | tristate "Wolfson Microelectronics Arizona class devices" | |
1084 | depends on MFD_ARIZONA | |
1085 | help | |
1086 | Support for GPIOs on Wolfson Arizona class devices. | |
1087 | ||
18bc64b3 MV |
1088 | config GPIO_BD70528 |
1089 | tristate "ROHM BD70528 GPIO support" | |
1090 | depends on MFD_ROHM_BD70528 | |
1091 | help | |
1092 | Support for GPIOs on ROHM BD70528 PMIC. There are four GPIOs | |
1093 | available on the ROHM PMIC in total. The GPIOs can also | |
1094 | generate interrupts. | |
1095 | ||
1096 | This driver can also be built as a module. If so, the module | |
1097 | will be called gpio-bd70528. | |
1098 | ||
c31f625d MV |
1099 | config GPIO_BD71828 |
1100 | tristate "ROHM BD71828 GPIO support" | |
1101 | depends on MFD_ROHM_BD71828 | |
1102 | help | |
1103 | Support for GPIOs on ROHM BD71828 PMIC. There are three GPIOs | |
1104 | available on the ROHM PMIC in total. The GPIOs are limited to | |
1105 | outputs only and pins must be configured to GPIO outputs by | |
1106 | OTP. Enable this only if you want to use these pins as outputs. | |
1107 | ||
1108 | This driver can also be built as a module. If so, the module | |
1109 | will be called gpio-bd71828. | |
1110 | ||
93847930 MV |
1111 | config GPIO_BD9571MWV |
1112 | tristate "ROHM BD9571 GPIO support" | |
1113 | depends on MFD_BD9571MWV | |
1114 | help | |
1115 | Support for GPIOs on ROHM BD9571 PMIC. There are two GPIOs | |
1116 | available on the ROHM PMIC in total, both of which can also | |
1117 | generate interrupts. | |
1118 | ||
1119 | This driver can also be built as a module. If so, the module | |
1120 | will be called gpio-bd9571mwv. | |
1121 | ||
be9cab5b LW |
1122 | config GPIO_CRYSTAL_COVE |
1123 | tristate "GPIO support for Crystal Cove PMIC" | |
72aba2e2 | 1124 | depends on (X86 || COMPILE_TEST) && INTEL_SOC_PMIC |
be9cab5b LW |
1125 | select GPIOLIB_IRQCHIP |
1126 | help | |
1127 | Support for GPIO pins on Crystal Cove PMIC. | |
1128 | ||
1129 | Say Yes if you have a Intel SoC based tablet with Crystal Cove PMIC | |
1130 | inside. | |
1131 | ||
1132 | This driver can also be built as a module. If so, the module will be | |
1133 | called gpio-crystalcove. | |
1134 | ||
1135 | config GPIO_CS5535 | |
1136 | tristate "AMD CS5535/CS5536 GPIO support" | |
72aba2e2 | 1137 | depends on X86 || MIPS || COMPILE_TEST |
be9cab5b LW |
1138 | depends on MFD_CS5535 |
1139 | help | |
1140 | The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that | |
1141 | can be used for quite a number of things. The CS5535/6 is found on | |
1142 | AMD Geode and Lemote Yeeloong devices. | |
1143 | ||
1144 | If unsure, say N. | |
1145 | ||
1146 | config GPIO_DA9052 | |
1147 | tristate "Dialog DA9052 GPIO" | |
1148 | depends on PMIC_DA9052 | |
1149 | help | |
1150 | Say yes here to enable the GPIO driver for the DA9052 chip. | |
1151 | ||
1152 | config GPIO_DA9055 | |
1153 | tristate "Dialog Semiconductor DA9055 GPIO" | |
1154 | depends on MFD_DA9055 | |
1155 | help | |
1156 | Say yes here to enable the GPIO driver for the DA9055 chip. | |
1157 | ||
1158 | The Dialog DA9055 PMIC chip has 3 GPIO pins that can be | |
1159 | be controller by this driver. | |
1160 | ||
1161 | If driver is built as a module it will be called gpio-da9055. | |
1162 | ||
1163 | config GPIO_DLN2 | |
1164 | tristate "Diolan DLN2 GPIO support" | |
1165 | depends on MFD_DLN2 | |
1166 | select GPIOLIB_IRQCHIP | |
1167 | ||
1168 | help | |
1169 | Select this option to enable GPIO driver for the Diolan DLN2 | |
1170 | board. | |
1171 | ||
1172 | This driver can also be built as a module. If so, the module | |
1173 | will be called gpio-dln2. | |
1174 | ||
3c6e8d05 LW |
1175 | config HTC_EGPIO |
1176 | bool "HTC EGPIO support" | |
e4c6a52c | 1177 | depends on ARM |
3c6e8d05 | 1178 | help |
c42e34c9 EWI |
1179 | This driver supports the CPLD egpio chip present on |
1180 | several HTC phones. It provides basic support for input | |
1181 | pins, output pins, and irqs. | |
3c6e8d05 | 1182 | |
be9cab5b LW |
1183 | config GPIO_JANZ_TTL |
1184 | tristate "Janz VMOD-TTL Digital IO Module" | |
1185 | depends on MFD_JANZ_CMODIO | |
1186 | help | |
1187 | This enables support for the Janz VMOD-TTL Digital IO module. | |
1188 | This driver provides support for driving the pins in output | |
1189 | mode only. Input mode is not supported. | |
1190 | ||
1191 | config GPIO_KEMPLD | |
1192 | tristate "Kontron ETX / COMexpress GPIO" | |
1193 | depends on MFD_KEMPLD | |
1194 | help | |
1195 | This enables support for the PLD GPIO interface on some Kontron ETX | |
1196 | and COMexpress (ETXexpress) modules. | |
1197 | ||
1198 | This driver can also be built as a module. If so, the module will be | |
1199 | called gpio-kempld. | |
1200 | ||
1201 | config GPIO_LP3943 | |
1202 | tristate "TI/National Semiconductor LP3943 GPIO expander" | |
1203 | depends on MFD_LP3943 | |
1204 | help | |
1205 | GPIO driver for LP3943 MFD. | |
1206 | LP3943 can be used as a GPIO expander which provides up to 16 GPIOs. | |
1207 | Open drain outputs are required for this usage. | |
1208 | ||
83f14103 K |
1209 | config GPIO_LP873X |
1210 | tristate "TI LP873X GPO" | |
1211 | depends on MFD_TI_LP873X | |
1212 | help | |
1213 | This driver supports the GPO on TI Lp873x PMICs. 2 GPOs are present | |
1214 | on LP873X PMICs. | |
1215 | ||
1216 | This driver can also be built as a module. If so, the module will be | |
c42e34c9 | 1217 | called gpio-lp873x. |
83f14103 | 1218 | |
5c7f2c76 K |
1219 | config GPIO_LP87565 |
1220 | tristate "TI LP87565 GPIO" | |
1221 | depends on MFD_TI_LP87565 | |
1222 | help | |
1223 | This driver supports the GPIO on TI Lp873565 PMICs. 3 GPIOs are present | |
1224 | on LP87565 PMICs. | |
1225 | ||
1226 | This driver can also be built as a module. If so, the module will be | |
1227 | called gpio-lp87565. | |
1228 | ||
aca429ff RF |
1229 | config GPIO_MADERA |
1230 | tristate "Cirrus Logic Madera class codecs" | |
1231 | depends on PINCTRL_MADERA | |
1232 | help | |
1233 | Support for GPIOs on Cirrus Logic Madera class codecs. | |
1234 | ||
02c5ba1e LD |
1235 | config GPIO_MAX77620 |
1236 | tristate "GPIO support for PMIC MAX77620 and MAX20024" | |
1237 | depends on MFD_MAX77620 | |
c5706c7d | 1238 | select GPIOLIB_IRQCHIP |
02c5ba1e LD |
1239 | help |
1240 | GPIO driver for MAX77620 and MAX20024 PMIC from Maxim Semiconductor. | |
1241 | MAX77620 PMIC has 8 pins that can be configured as GPIOs. The | |
1242 | driver also provides interrupt support for each of the gpios. | |
1243 | Say yes here to enable the max77620 to be used as gpio controller. | |
1244 | ||
72b5135b BG |
1245 | config GPIO_MAX77650 |
1246 | tristate "Maxim MAX77650/77651 GPIO support" | |
1247 | depends on MFD_MAX77650 | |
1248 | help | |
1249 | GPIO driver for MAX77650/77651 PMIC from Maxim Semiconductor. | |
1250 | These chips have a single pin that can be configured as GPIO. | |
1251 | ||
be9cab5b LW |
1252 | config GPIO_MSIC |
1253 | bool "Intel MSIC mixed signal gpio support" | |
72aba2e2 | 1254 | depends on (X86 || COMPILE_TEST) && MFD_INTEL_MSIC |
be9cab5b LW |
1255 | help |
1256 | Enable support for GPIO on intel MSIC controllers found in | |
1257 | intel MID devices | |
1258 | ||
1259 | config GPIO_PALMAS | |
1260 | bool "TI PALMAS series PMICs GPIO" | |
1261 | depends on MFD_PALMAS | |
1262 | help | |
1263 | Select this option to enable GPIO driver for the TI PALMAS | |
1264 | series chip family. | |
1265 | ||
e9fe32bc LD |
1266 | config GPIO_RC5T583 |
1267 | bool "RICOH RC5T583 GPIO" | |
1268 | depends on MFD_RC5T583 | |
1269 | help | |
1270 | Select this option to enable GPIO driver for the Ricoh RC5T583 | |
1271 | chip family. | |
1272 | This driver provides the support for driving/reading the gpio pins | |
1273 | of RC5T583 device through standard gpio library. | |
1274 | ||
b7536d87 MW |
1275 | config GPIO_SL28CPLD |
1276 | tristate "Kontron sl28cpld GPIO support" | |
1277 | depends on MFD_SL28CPLD || COMPILE_TEST | |
1278 | select GPIO_REGMAP | |
1279 | select GPIOLIB_IRQCHIP | |
1280 | select REGMAP_IRQ | |
1281 | help | |
1282 | This enables support for the GPIOs found on the Kontron sl28 CPLD. | |
1283 | ||
1284 | This driver can also be built as a module. If so, the module will be | |
1285 | called gpio-sl28cpld. | |
1286 | ||
03f822f5 RV |
1287 | config GPIO_STMPE |
1288 | bool "STMPE GPIOs" | |
1289 | depends on MFD_STMPE | |
1dfb4a0d | 1290 | depends on OF_GPIO |
fe44e70d | 1291 | select GPIOLIB_IRQCHIP |
03f822f5 RV |
1292 | help |
1293 | This enables support for the GPIOs found on the STMPE I/O | |
1294 | Expanders. | |
1295 | ||
f4e8afdc SI |
1296 | config GPIO_TC3589X |
1297 | bool "TC3589X GPIOs" | |
1298 | depends on MFD_TC3589X | |
1422731d | 1299 | depends on OF_GPIO |
cf42f1cf | 1300 | select GPIOLIB_IRQCHIP |
d88b25be | 1301 | help |
f4e8afdc | 1302 | This enables support for the GPIOs found on the TC3589X |
d88b25be RV |
1303 | I/O Expander. |
1304 | ||
be9cab5b LW |
1305 | config GPIO_TIMBERDALE |
1306 | bool "Support for timberdale GPIO IP" | |
1307 | depends on MFD_TIMBERDALE | |
a7f7f624 | 1308 | help |
be9cab5b LW |
1309 | Add support for the GPIO IP in the timberdale FPGA. |
1310 | ||
99f0fd54 AD |
1311 | config GPIO_TPS65086 |
1312 | tristate "TI TPS65086 GPO" | |
1313 | depends on MFD_TPS65086 | |
1314 | help | |
1315 | This driver supports the GPO on TI TPS65086x PMICs. | |
1316 | ||
c366c76a NSJ |
1317 | config GPIO_TPS65218 |
1318 | tristate "TPS65218 GPIO" | |
1319 | depends on MFD_TPS65218 | |
1320 | help | |
1321 | Select this option to enable GPIO driver for the TPS65218 | |
1322 | chip family. | |
1323 | ||
be9cab5b LW |
1324 | config GPIO_TPS6586X |
1325 | bool "TPS6586X GPIO" | |
1326 | depends on MFD_TPS6586X | |
1327 | help | |
1328 | Select this option to enable GPIO driver for the TPS6586X | |
1329 | chip family. | |
1330 | ||
1331 | config GPIO_TPS65910 | |
1332 | bool "TPS65910 GPIO" | |
1333 | depends on MFD_TPS65910 | |
1334 | help | |
1335 | Select this option to enable GPIO driver for the TPS65910 | |
1336 | chip family. | |
1337 | ||
668a6cc7 MO |
1338 | config GPIO_TPS65912 |
1339 | tristate "TI TPS65912 GPIO" | |
ca801a22 | 1340 | depends on MFD_TPS65912 |
668a6cc7 MO |
1341 | help |
1342 | This driver supports TPS65912 gpio chip | |
1343 | ||
275b13a6 RM |
1344 | config GPIO_TPS68470 |
1345 | bool "TPS68470 GPIO" | |
1346 | depends on MFD_TPS68470 | |
1347 | help | |
1348 | Select this option to enable GPIO driver for the TPS68470 | |
1349 | chip family. | |
1350 | There are 7 GPIOs and few sensor related GPIOs supported | |
1351 | by the TPS68470. While the 7 GPIOs can be configured as | |
1352 | input or output as appropriate, the sensor related GPIOs | |
1353 | are "output only" GPIOs. | |
1354 | ||
1355 | This driver config is bool, as the GPIO functionality | |
1356 | of the TPS68470 must be available before dependent | |
1357 | drivers are loaded. | |
1358 | ||
b868db94 AL |
1359 | config GPIO_TQMX86 |
1360 | tristate "TQ-Systems QTMX86 GPIO" | |
1361 | depends on MFD_TQMX86 || COMPILE_TEST | |
1362 | select GPIOLIB_IRQCHIP | |
1363 | help | |
1364 | This driver supports GPIO on the TQMX86 IO controller. | |
1365 | ||
e9d35947 DB |
1366 | config GPIO_TWL4030 |
1367 | tristate "TWL4030, TWL5030, and TPS659x0 GPIOs" | |
1368 | depends on TWL4030_CORE | |
1369 | help | |
1370 | Say yes here to access the GPIO signals of various multi-function | |
1371 | power management chips from Texas Instruments. | |
1372 | ||
70ffd691 PU |
1373 | config GPIO_TWL6040 |
1374 | tristate "TWL6040 GPO" | |
1375 | depends on TWL6040_CORE | |
1376 | help | |
1377 | Say yes here to access the GPO signals of twl6040 | |
1378 | audio chip from Texas Instruments. | |
1379 | ||
be9cab5b LW |
1380 | config GPIO_UCB1400 |
1381 | tristate "Philips UCB1400 GPIO" | |
1382 | depends on UCB1400_CORE | |
1383 | help | |
1384 | This enables support for the Philips UCB1400 GPIO pins. | |
1385 | The UCB1400 is an AC97 audio codec. | |
1386 | ||
0ba19cfc BG |
1387 | config GPIO_WHISKEY_COVE |
1388 | tristate "GPIO support for Whiskey Cove PMIC" | |
b5238b41 | 1389 | depends on (X86 || COMPILE_TEST) && INTEL_SOC_PMIC_BXTWC |
0ba19cfc BG |
1390 | select GPIOLIB_IRQCHIP |
1391 | help | |
1392 | Support for GPIO pins on Whiskey Cove PMIC. | |
1393 | ||
1394 | Say Yes if you have a Intel SoC based tablet with Whiskey Cove PMIC | |
1395 | inside. | |
1396 | ||
1397 | This driver can also be built as a module. If so, the module will be | |
1398 | called gpio-wcove. | |
1399 | ||
e4b736f1 MB |
1400 | config GPIO_WM831X |
1401 | tristate "WM831x GPIOs" | |
1402 | depends on MFD_WM831X | |
1403 | help | |
1404 | Say yes here to access the GPIO signals of WM831x power management | |
1405 | chips from Wolfson Microelectronics. | |
1406 | ||
38f6ce45 MB |
1407 | config GPIO_WM8350 |
1408 | tristate "WM8350 GPIOs" | |
1409 | depends on MFD_WM8350 | |
1410 | help | |
1411 | Say yes here to access the GPIO signals of WM8350 power management | |
1412 | chips from Wolfson Microelectronics. | |
1413 | ||
2955c309 MB |
1414 | config GPIO_WM8994 |
1415 | tristate "WM8994 GPIOs" | |
1416 | depends on MFD_WM8994 | |
1417 | help | |
1418 | Say yes here to access the GPIO signals of WM8994 audio hub | |
1419 | CODECs from Wolfson Microelectronics. | |
1420 | ||
177b0381 | 1421 | endmenu |
ef72af40 | 1422 | |
177b0381 LW |
1423 | menu "PCI GPIO expanders" |
1424 | depends on PCI | |
459773ae | 1425 | |
92c33ef7 LW |
1426 | config GPIO_AMD8111 |
1427 | tristate "AMD 8111 GPIO driver" | |
72aba2e2 | 1428 | depends on X86 || COMPILE_TEST |
5e969a40 | 1429 | help |
92c33ef7 | 1430 | The AMD 8111 south bridge contains 32 GPIO pins which can be used. |
ff1d5c2f | 1431 | |
92c33ef7 LW |
1432 | Note, that usually system firmware/ACPI handles GPIO pins on their |
1433 | own and users might easily break their systems with uncarefull usage | |
1434 | of this driver! | |
5f0a96b0 | 1435 | |
92c33ef7 | 1436 | If unsure, say N |
5f0a96b0 | 1437 | |
ff1d5c2f MB |
1438 | config GPIO_BT8XX |
1439 | tristate "BT8XX GPIO abuser" | |
03744529 | 1440 | depends on VIDEO_BT848=n |
ff1d5c2f | 1441 | help |
22520edc | 1442 | The BT8xx frame grabber chip has 24 GPIO pins that can be abused |
ff1d5c2f MB |
1443 | as a cheap PCI GPIO card. |
1444 | ||
1445 | This chip can be found on Miro, Hauppauge and STB TV-cards. | |
1446 | ||
1447 | The card needs to be physically altered for using it as a | |
1448 | GPIO card. For more information on how to build a GPIO card | |
1449 | from a BT8xx TV card, see the documentation file at | |
5f07224e | 1450 | Documentation/driver-api/gpio/bt8xxgpio.rst |
ff1d5c2f MB |
1451 | |
1452 | If unsure, say N. | |
1453 | ||
84743ea3 | 1454 | config GPIO_INTEL_MID |
c78e3cf1 AS |
1455 | bool "Intel MID GPIO support" |
1456 | depends on X86_INTEL_MID | |
fc346270 | 1457 | select GPIOLIB_IRQCHIP |
8bf02617 | 1458 | help |
c78e3cf1 | 1459 | Say Y here to support Intel MID GPIO. |
8bf02617 | 1460 | |
ccf6fd6d AS |
1461 | config GPIO_MERRIFIELD |
1462 | tristate "Intel Merrifield GPIO support" | |
1463 | depends on X86_INTEL_MID | |
fc346270 | 1464 | select GPIOLIB_IRQCHIP |
8bf02617 | 1465 | help |
ccf6fd6d | 1466 | Say Y here to support Intel Merrifield GPIO. |
8bf02617 | 1467 | |
c78c42d7 SKR |
1468 | config GPIO_MLXBF |
1469 | tristate "Mellanox BlueField SoC GPIO" | |
cbe706b0 | 1470 | depends on (MELLANOX_PLATFORM && ARM64 && ACPI) || (64BIT && COMPILE_TEST) |
c78c42d7 SKR |
1471 | select GPIO_GENERIC |
1472 | help | |
1473 | Say Y here if you want GPIO support on Mellanox BlueField SoC. | |
1474 | ||
bc0ae0e7 AM |
1475 | config GPIO_MLXBF2 |
1476 | tristate "Mellanox BlueField 2 SoC GPIO" | |
1477 | depends on (MELLANOX_PLATFORM && ARM64 && ACPI) || (64BIT && COMPILE_TEST) | |
1478 | select GPIO_GENERIC | |
1479 | help | |
1480 | Say Y here if you want GPIO support on Mellanox BlueField 2 SoC. | |
1481 | ||
92c33ef7 LW |
1482 | config GPIO_ML_IOH |
1483 | tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support" | |
72aba2e2 | 1484 | depends on X86 || COMPILE_TEST |
92c33ef7 LW |
1485 | select GENERIC_IRQ_CHIP |
1486 | help | |
1487 | ML7213 is companion chip for Intel Atom E6xx series. | |
1488 | This driver can be used for OKI SEMICONDUCTOR ML7213 IOH(Input/Output | |
1489 | Hub) which is for IVI(In-Vehicle Infotainment) use. | |
1490 | This driver can access the IOH's GPIO device. | |
1491 | ||
04c17aa8 | 1492 | config GPIO_PCH |
868fea05 | 1493 | tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7223/ML7831) GPIO" |
03744529 | 1494 | depends on X86_32 || MIPS || COMPILE_TEST |
38eb18a6 | 1495 | select GENERIC_IRQ_CHIP |
04c17aa8 TM |
1496 | help |
1497 | This driver is for PCH(Platform controller Hub) GPIO of Intel Topcliff | |
1498 | which is an IOH(Input/Output Hub) for x86 embedded processor. | |
1499 | This driver can access PCH GPIO device. | |
1500 | ||
868fea05 TM |
1501 | This driver also can be used for LAPIS Semiconductor IOH(Input/ |
1502 | Output Hub), ML7223 and ML7831. | |
bc786cce | 1503 | ML7223 IOH is for MP(Media Phone) use. |
868fea05 TM |
1504 | ML7831 IOH is for general purpose use. |
1505 | ML7223/ML7831 is companion chip for Intel Atom E6xx series. | |
1506 | ML7223/ML7831 is completely compatible for Intel EG20T PCH. | |
bc786cce | 1507 | |
02e74fc0 WBG |
1508 | config GPIO_PCI_IDIO_16 |
1509 | tristate "ACCES PCI-IDIO-16 GPIO support" | |
1510 | select GPIOLIB_IRQCHIP | |
1511 | help | |
1512 | Enables GPIO support for the ACCES PCI-IDIO-16. An interrupt is | |
1513 | generated when any of the inputs change state (low to high or high to | |
1514 | low). Input filter control is not supported by this driver, and the | |
1515 | input filters are deactivated by this driver. | |
1516 | ||
58556204 WBG |
1517 | config GPIO_PCIE_IDIO_24 |
1518 | tristate "ACCES PCIe-IDIO-24 GPIO support" | |
1519 | select GPIOLIB_IRQCHIP | |
1520 | help | |
1521 | Enables GPIO support for the ACCES PCIe-IDIO-24 family (PCIe-IDIO-24, | |
1522 | PCIe-IDI-24, PCIe-IDO-24, PCIe-IDIO-12). An interrupt is generated | |
1523 | when any of the inputs change state (low to high or high to low). | |
1524 | Input filter control is not supported by this driver, and the input | |
1525 | filters are deactivated by this driver. | |
1526 | ||
92c33ef7 LW |
1527 | config GPIO_RDC321X |
1528 | tristate "RDC R-321x GPIO support" | |
92c33ef7 LW |
1529 | select MFD_CORE |
1530 | select MFD_RDC321X | |
49a36793 | 1531 | help |
92c33ef7 LW |
1532 | Support for the RDC R321x SoC GPIOs over southbridge |
1533 | PCI configuration space. | |
49a36793 | 1534 | |
b43ab901 SAS |
1535 | config GPIO_SODAVILLE |
1536 | bool "Intel Sodaville GPIO support" | |
03744529 | 1537 | depends on X86 && OF |
b43ab901 SAS |
1538 | select GPIO_GENERIC |
1539 | select GENERIC_IRQ_CHIP | |
1540 | help | |
1541 | Say Y here to support Intel Sodaville GPIO. | |
1542 | ||
177b0381 | 1543 | endmenu |
35570ac6 | 1544 | |
177b0381 LW |
1545 | menu "SPI GPIO expanders" |
1546 | depends on SPI_MASTER | |
9956d02d | 1547 | |
a7ec2e7f LW |
1548 | config GPIO_74X164 |
1549 | tristate "74x164 serial-in/parallel-out 8-bits shift register" | |
048c28c9 | 1550 | depends on OF_GPIO |
a7ec2e7f LW |
1551 | help |
1552 | Driver for 74x164 compatible serial-in/parallel-out 8-outputs | |
1553 | shift registers. This driver can be used to provide access | |
1554 | to more gpio outputs. | |
a9c5fff5 | 1555 | |
b2f68edf LW |
1556 | config GPIO_MAX3191X |
1557 | tristate "Maxim MAX3191x industrial serializer" | |
1558 | select CRC8 | |
1559 | help | |
1560 | GPIO driver for Maxim MAX31910, MAX31911, MAX31912, MAX31913, | |
1561 | MAX31953 and MAX31963 industrial serializer, a daisy-chainable | |
1562 | chip to make 8 digital 24V inputs available via SPI. Supports | |
1563 | CRC checksums to guard against electromagnetic interference, | |
1564 | as well as undervoltage and overtemperature detection. | |
1565 | ||
0c36ec31 JB |
1566 | config GPIO_MAX7301 |
1567 | tristate "Maxim MAX7301 GPIO expander" | |
e952805d | 1568 | select GPIO_MAX730X |
0c36ec31 | 1569 | help |
e952805d | 1570 | GPIO driver for Maxim MAX7301 SPI-based GPIO expander. |
0c36ec31 | 1571 | |
1e5db006 RR |
1572 | config GPIO_MC33880 |
1573 | tristate "Freescale MC33880 high-side/low-side switch" | |
1e5db006 RR |
1574 | help |
1575 | SPI driver for Freescale MC33880 high-side/low-side switch. | |
1576 | This provides GPIO interface supporting inputs and outputs. | |
1577 | ||
df6df93c AD |
1578 | config GPIO_PISOSR |
1579 | tristate "Generic parallel-in/serial-out shift register" | |
1580 | help | |
1581 | GPIO driver for SPI compatible parallel-in/serial-out shift | |
1582 | registers. These are input only devices. | |
1583 | ||
5704520d NH |
1584 | config GPIO_XRA1403 |
1585 | tristate "EXAR XRA1403 16-bit GPIO expander" | |
665dff99 | 1586 | select REGMAP_SPI |
5704520d NH |
1587 | help |
1588 | GPIO driver for EXAR XRA1403 16-bit SPI-based GPIO expander. | |
1589 | ||
856ed97a MB |
1590 | config GPIO_MOXTET |
1591 | tristate "Turris Mox Moxtet bus GPIO expander" | |
1592 | depends on MOXTET | |
1593 | help | |
1594 | Say yes here if you are building for the Turris Mox router. | |
1595 | This is the driver needed for configuring the GPIOs via the Moxtet | |
1596 | bus. For example the Mox module with SFP cage needs this driver | |
1597 | so that phylink can use corresponding GPIOs. | |
1598 | ||
0963670a LW |
1599 | endmenu |
1600 | ||
177b0381 LW |
1601 | menu "USB GPIO expanders" |
1602 | depends on USB | |
9d5b72de LP |
1603 | |
1604 | config GPIO_VIPERBOARD | |
1605 | tristate "Viperboard GPIO a & b support" | |
03744529 | 1606 | depends on MFD_VIPERBOARD |
9d5b72de LP |
1607 | help |
1608 | Say yes here to access the GPIO signals of Nano River | |
1609 | Technologies Viperboard. There are two GPIO chips on the | |
1610 | board: gpioa and gpiob. | |
c42e34c9 EWI |
1611 | See viperboard API specification and Nano |
1612 | River Tech's viperboard.h for detailed meaning | |
1613 | of the module parameters. | |
9d5b72de | 1614 | |
177b0381 | 1615 | endmenu |
6732127f | 1616 | |
b5252196 EWI |
1617 | menu "Virtual GPIO drivers" |
1618 | ||
828546e2 GU |
1619 | config GPIO_AGGREGATOR |
1620 | tristate "GPIO Aggregator" | |
1621 | help | |
1622 | Say yes here to enable the GPIO Aggregator, which provides a way to | |
1623 | aggregate existing GPIO lines into a new virtual GPIO chip. | |
1624 | This can serve the following purposes: | |
1625 | - Assign permissions for a collection of GPIO lines to a user, | |
1626 | - Export a collection of GPIO lines to a virtual machine, | |
1627 | - Provide a generic driver for a GPIO-operated device in an | |
1628 | industrial control context, to be operated from userspace using | |
1629 | the GPIO chardev interface. | |
1630 | ||
6e4484ee BG |
1631 | config GPIO_MOCKUP |
1632 | tristate "GPIO Testing Driver" | |
6e4484ee BG |
1633 | select IRQ_SIM |
1634 | help | |
1635 | This enables GPIO Testing driver, which provides a way to test GPIO | |
1636 | subsystem through sysfs(or char device) and debugfs. GPIO_SYSFS | |
1637 | must be selected for this test. | |
1638 | User could use it through the script in | |
1639 | tools/testing/selftests/gpio/gpio-mockup.sh. Reference the usage in | |
1640 | it. | |
1641 | ||
b5252196 EWI |
1642 | endmenu |
1643 | ||
7444a72e | 1644 | endif |