Commit | Line | Data |
---|---|---|
669a5db4 JG |
1 | /* |
2 | * pata_via.c - VIA PATA for new ATA layer | |
3 | * (C) 2005-2006 Red Hat Inc | |
669a5db4 JG |
4 | * |
5 | * Documentation | |
6 | * Most chipset documentation available under NDA only | |
7 | * | |
8 | * VIA version guide | |
9 | * VIA VT82C561 - early design, uses ata_generic currently | |
10 | * VIA VT82C576 - MWDMA, 33Mhz | |
11 | * VIA VT82C586 - MWDMA, 33Mhz | |
12 | * VIA VT82C586a - Added UDMA to 33Mhz | |
13 | * VIA VT82C586b - UDMA33 | |
14 | * VIA VT82C596a - Nonfunctional UDMA66 | |
15 | * VIA VT82C596b - Working UDMA66 | |
16 | * VIA VT82C686 - Nonfunctional UDMA66 | |
17 | * VIA VT82C686a - Working UDMA66 | |
18 | * VIA VT82C686b - Updated to UDMA100 | |
19 | * VIA VT8231 - UDMA100 | |
20 | * VIA VT8233 - UDMA100 | |
21 | * VIA VT8233a - UDMA133 | |
22 | * VIA VT8233c - UDMA100 | |
23 | * VIA VT8235 - UDMA133 | |
24 | * VIA VT8237 - UDMA133 | |
05c39e50 | 25 | * VIA VT8237S - UDMA133 |
75f609d2 | 26 | * VIA VT8251 - UDMA133 |
669a5db4 JG |
27 | * |
28 | * Most registers remain compatible across chips. Others start reserved | |
29 | * and acquire sensible semantics if set to 1 (eg cable detect). A few | |
30 | * exceptions exist, notably around the FIFO settings. | |
31 | * | |
32 | * One additional quirk of the VIA design is that like ALi they use few | |
33 | * PCI IDs for a lot of chips. | |
34 | * | |
35 | * Based heavily on: | |
36 | * | |
37 | * Version 3.38 | |
38 | * | |
39 | * VIA IDE driver for Linux. Supported southbridges: | |
40 | * | |
41 | * vt82c576, vt82c586, vt82c586a, vt82c586b, vt82c596a, vt82c596b, | |
42 | * vt82c686, vt82c686a, vt82c686b, vt8231, vt8233, vt8233c, vt8233a, | |
43 | * vt8235, vt8237 | |
44 | * | |
45 | * Copyright (c) 2000-2002 Vojtech Pavlik | |
46 | * | |
47 | * Based on the work of: | |
48 | * Michel Aubry | |
49 | * Jeff Garzik | |
50 | * Andre Hedrick | |
51 | ||
52 | */ | |
53 | ||
54 | #include <linux/kernel.h> | |
55 | #include <linux/module.h> | |
56 | #include <linux/pci.h> | |
57 | #include <linux/init.h> | |
58 | #include <linux/blkdev.h> | |
59 | #include <linux/delay.h> | |
60 | #include <scsi/scsi_host.h> | |
61 | #include <linux/libata.h> | |
cf5792d2 | 62 | #include <linux/dmi.h> |
669a5db4 JG |
63 | |
64 | #define DRV_NAME "pata_via" | |
943547ab | 65 | #define DRV_VERSION "0.3.3" |
669a5db4 JG |
66 | |
67 | /* | |
68 | * The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx | |
69 | * driver. | |
70 | */ | |
71 | ||
72 | enum { | |
73 | VIA_UDMA = 0x007, | |
74 | VIA_UDMA_NONE = 0x000, | |
75 | VIA_UDMA_33 = 0x001, | |
76 | VIA_UDMA_66 = 0x002, | |
77 | VIA_UDMA_100 = 0x003, | |
78 | VIA_UDMA_133 = 0x004, | |
79 | VIA_BAD_PREQ = 0x010, /* Crashes if PREQ# till DDACK# set */ | |
80 | VIA_BAD_CLK66 = 0x020, /* 66 MHz clock doesn't work correctly */ | |
81 | VIA_SET_FIFO = 0x040, /* Needs to have FIFO split set */ | |
82 | VIA_NO_UNMASK = 0x080, /* Doesn't work with IRQ unmasking on */ | |
83 | VIA_BAD_ID = 0x100, /* Has wrong vendor ID (0x1107) */ | |
84 | VIA_BAD_AST = 0x200, /* Don't touch Address Setup Timing */ | |
85 | VIA_NO_ENABLES = 0x400, /* Has no enablebits */ | |
7585eb1b | 86 | VIA_SATA_PATA = 0x800, /* SATA/PATA combined configuration */ |
669a5db4 JG |
87 | }; |
88 | ||
89 | /* | |
90 | * VIA SouthBridge chips. | |
91 | */ | |
92 | ||
93 | static const struct via_isa_bridge { | |
94 | const char *name; | |
95 | u16 id; | |
96 | u8 rev_min; | |
97 | u8 rev_max; | |
98 | u16 flags; | |
99 | } via_isa_bridges[] = { | |
bfce5e01 J |
100 | { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, VIA_UDMA_133 | |
101 | VIA_BAD_AST | VIA_SATA_PATA }, | |
e0b874df | 102 | { "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, |
75f609d2 | 103 | { "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, |
7585eb1b | 104 | { "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_SATA_PATA }, |
669a5db4 JG |
105 | { "vt6410", PCI_DEVICE_ID_VIA_6410, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_NO_ENABLES}, |
106 | { "vt8237a", PCI_DEVICE_ID_VIA_8237A, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, | |
107 | { "vt8237", PCI_DEVICE_ID_VIA_8237, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, | |
108 | { "vt8235", PCI_DEVICE_ID_VIA_8235, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, | |
109 | { "vt8233a", PCI_DEVICE_ID_VIA_8233A, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST }, | |
110 | { "vt8233c", PCI_DEVICE_ID_VIA_8233C_0, 0x00, 0x2f, VIA_UDMA_100 }, | |
111 | { "vt8233", PCI_DEVICE_ID_VIA_8233_0, 0x00, 0x2f, VIA_UDMA_100 }, | |
112 | { "vt8231", PCI_DEVICE_ID_VIA_8231, 0x00, 0x2f, VIA_UDMA_100 }, | |
113 | { "vt82c686b", PCI_DEVICE_ID_VIA_82C686, 0x40, 0x4f, VIA_UDMA_100 }, | |
114 | { "vt82c686a", PCI_DEVICE_ID_VIA_82C686, 0x10, 0x2f, VIA_UDMA_66 }, | |
115 | { "vt82c686", PCI_DEVICE_ID_VIA_82C686, 0x00, 0x0f, VIA_UDMA_33 | VIA_BAD_CLK66 }, | |
116 | { "vt82c596b", PCI_DEVICE_ID_VIA_82C596, 0x10, 0x2f, VIA_UDMA_66 }, | |
117 | { "vt82c596a", PCI_DEVICE_ID_VIA_82C596, 0x00, 0x0f, VIA_UDMA_33 | VIA_BAD_CLK66 }, | |
118 | { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x47, 0x4f, VIA_UDMA_33 | VIA_SET_FIFO }, | |
119 | { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x40, 0x46, VIA_UDMA_33 | VIA_SET_FIFO | VIA_BAD_PREQ }, | |
120 | { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x30, 0x3f, VIA_UDMA_33 | VIA_SET_FIFO }, | |
121 | { "vt82c586a", PCI_DEVICE_ID_VIA_82C586_0, 0x20, 0x2f, VIA_UDMA_33 | VIA_SET_FIFO }, | |
122 | { "vt82c586", PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f, VIA_UDMA_NONE | VIA_SET_FIFO }, | |
123 | { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, VIA_UDMA_NONE | VIA_SET_FIFO | VIA_NO_UNMASK }, | |
124 | { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, VIA_UDMA_NONE | VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID }, | |
125 | { NULL } | |
126 | }; | |
127 | ||
cf5792d2 AC |
128 | |
129 | /* | |
130 | * Cable special cases | |
131 | */ | |
132 | ||
1855256c | 133 | static const struct dmi_system_id cable_dmi_table[] = { |
cf5792d2 AC |
134 | { |
135 | .ident = "Acer Ferrari 3400", | |
136 | .matches = { | |
137 | DMI_MATCH(DMI_BOARD_VENDOR, "Acer,Inc."), | |
138 | DMI_MATCH(DMI_BOARD_NAME, "Ferrari 3400"), | |
139 | }, | |
140 | }, | |
141 | { } | |
142 | }; | |
143 | ||
144 | static int via_cable_override(struct pci_dev *pdev) | |
145 | { | |
146 | /* Systems by DMI */ | |
147 | if (dmi_check_system(cable_dmi_table)) | |
148 | return 1; | |
9edbdbea AC |
149 | /* Arima W730-K8/Targa Visionary 811/... */ |
150 | if (pdev->subsystem_vendor == 0x161F && pdev->subsystem_device == 0x2032) | |
151 | return 1; | |
cf5792d2 AC |
152 | return 0; |
153 | } | |
154 | ||
155 | ||
669a5db4 JG |
156 | /** |
157 | * via_cable_detect - cable detection | |
158 | * @ap: ATA port | |
159 | * | |
160 | * Perform cable detection. Actually for the VIA case the BIOS | |
161 | * already did this for us. We read the values provided by the | |
162 | * BIOS. If you are using an 8235 in a non-PC configuration you | |
163 | * may need to update this code. | |
164 | * | |
165 | * Hotplug also impacts on this. | |
166 | */ | |
167 | ||
168 | static int via_cable_detect(struct ata_port *ap) { | |
97cb81c3 | 169 | const struct via_isa_bridge *config = ap->host->private_data; |
669a5db4 JG |
170 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
171 | u32 ata66; | |
172 | ||
cf5792d2 AC |
173 | if (via_cable_override(pdev)) |
174 | return ATA_CBL_PATA40_SHORT; | |
175 | ||
7585eb1b TH |
176 | if ((config->flags & VIA_SATA_PATA) && ap->port_no == 0) |
177 | return ATA_CBL_SATA; | |
178 | ||
97cb81c3 AC |
179 | /* Early chips are 40 wire */ |
180 | if ((config->flags & VIA_UDMA) < VIA_UDMA_66) | |
181 | return ATA_CBL_PATA40; | |
182 | /* UDMA 66 chips have only drive side logic */ | |
b447916e | 183 | else if ((config->flags & VIA_UDMA) < VIA_UDMA_100) |
97cb81c3 AC |
184 | return ATA_CBL_PATA_UNK; |
185 | /* UDMA 100 or later */ | |
669a5db4 JG |
186 | pci_read_config_dword(pdev, 0x50, &ata66); |
187 | /* Check both the drive cable reporting bits, we might not have | |
188 | two drives */ | |
189 | if (ata66 & (0x10100000 >> (16 * ap->port_no))) | |
190 | return ATA_CBL_PATA80; | |
7d73a363 | 191 | /* Check with ACPI so we can spot BIOS reported SATA bridges */ |
021ee9a6 TH |
192 | if (ata_acpi_init_gtm(ap) && |
193 | ata_acpi_cbl_80wire(ap, ata_acpi_init_gtm(ap))) | |
7d73a363 | 194 | return ATA_CBL_PATA80; |
97cb81c3 | 195 | return ATA_CBL_PATA40; |
669a5db4 JG |
196 | } |
197 | ||
cc0680a5 | 198 | static int via_pre_reset(struct ata_link *link, unsigned long deadline) |
669a5db4 | 199 | { |
cc0680a5 | 200 | struct ata_port *ap = link->ap; |
669a5db4 JG |
201 | const struct via_isa_bridge *config = ap->host->private_data; |
202 | ||
203 | if (!(config->flags & VIA_NO_ENABLES)) { | |
204 | static const struct pci_bits via_enable_bits[] = { | |
205 | { 0x40, 1, 0x02, 0x02 }, | |
206 | { 0x40, 1, 0x01, 0x01 } | |
207 | }; | |
669a5db4 | 208 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
c961922b AC |
209 | if (!pci_test_config_bits(pdev, &via_enable_bits[ap->port_no])) |
210 | return -ENOENT; | |
669a5db4 | 211 | } |
d4b2bab4 | 212 | |
9363c382 | 213 | return ata_sff_prereset(link, deadline); |
669a5db4 JG |
214 | } |
215 | ||
216 | ||
669a5db4 JG |
217 | /** |
218 | * via_do_set_mode - set initial PIO mode data | |
219 | * @ap: ATA interface | |
220 | * @adev: ATA device | |
221 | * @mode: ATA mode being programmed | |
222 | * @tdiv: Clocks per PCI clock | |
223 | * @set_ast: Set to program address setup | |
224 | * @udma_type: UDMA mode/format of registers | |
225 | * | |
226 | * Program the VIA registers for DMA and PIO modes. Uses the ata timing | |
227 | * support in order to compute modes. | |
228 | * | |
229 | * FIXME: Hotplug will require we serialize multiple mode changes | |
230 | * on the two channels. | |
231 | */ | |
232 | ||
233 | static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mode, int tdiv, int set_ast, int udma_type) | |
234 | { | |
235 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
236 | struct ata_device *peer = ata_dev_pair(adev); | |
237 | struct ata_timing t, p; | |
238 | static int via_clock = 33333; /* Bus clock in kHZ - ought to be tunable one day */ | |
239 | unsigned long T = 1000000000 / via_clock; | |
240 | unsigned long UT = T/tdiv; | |
241 | int ut; | |
242 | int offset = 3 - (2*ap->port_no) - adev->devno; | |
243 | ||
669a5db4 JG |
244 | /* Calculate the timing values we require */ |
245 | ata_timing_compute(adev, mode, &t, T, UT); | |
246 | ||
247 | /* We share 8bit timing so we must merge the constraints */ | |
248 | if (peer) { | |
249 | if (peer->pio_mode) { | |
250 | ata_timing_compute(peer, peer->pio_mode, &p, T, UT); | |
251 | ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT); | |
252 | } | |
253 | } | |
254 | ||
255 | /* Address setup is programmable but breaks on UDMA133 setups */ | |
256 | if (set_ast) { | |
257 | u8 setup; /* 2 bits per drive */ | |
258 | int shift = 2 * offset; | |
259 | ||
260 | pci_read_config_byte(pdev, 0x4C, &setup); | |
261 | setup &= ~(3 << shift); | |
07633b5d | 262 | setup |= clamp_val(t.setup, 1, 4) << shift; /* 1,4 or 1,4 - 1 FIXME */ |
669a5db4 JG |
263 | pci_write_config_byte(pdev, 0x4C, setup); |
264 | } | |
265 | ||
266 | /* Load the PIO mode bits */ | |
267 | pci_write_config_byte(pdev, 0x4F - ap->port_no, | |
07633b5d | 268 | ((clamp_val(t.act8b, 1, 16) - 1) << 4) | (clamp_val(t.rec8b, 1, 16) - 1)); |
669a5db4 | 269 | pci_write_config_byte(pdev, 0x48 + offset, |
07633b5d | 270 | ((clamp_val(t.active, 1, 16) - 1) << 4) | (clamp_val(t.recover, 1, 16) - 1)); |
669a5db4 JG |
271 | |
272 | /* Load the UDMA bits according to type */ | |
273 | switch(udma_type) { | |
274 | default: | |
275 | /* BUG() ? */ | |
276 | /* fall through */ | |
277 | case 33: | |
07633b5d | 278 | ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 5) - 2)) : 0x03; |
669a5db4 JG |
279 | break; |
280 | case 66: | |
07633b5d | 281 | ut = t.udma ? (0xe8 | (clamp_val(t.udma, 2, 9) - 2)) : 0x0f; |
669a5db4 JG |
282 | break; |
283 | case 100: | |
07633b5d | 284 | ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07; |
669a5db4 JG |
285 | break; |
286 | case 133: | |
07633b5d | 287 | ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07; |
669a5db4 JG |
288 | break; |
289 | } | |
08ebd43d | 290 | |
669a5db4 | 291 | /* Set UDMA unless device is not UDMA capable */ |
943547ab | 292 | if (udma_type && t.udma) { |
08ebd43d LR |
293 | u8 cable80_status; |
294 | ||
295 | /* Get 80-wire cable detection bit */ | |
296 | pci_read_config_byte(pdev, 0x50 + offset, &cable80_status); | |
297 | cable80_status &= 0x10; | |
298 | ||
299 | pci_write_config_byte(pdev, 0x50 + offset, ut | cable80_status); | |
300 | } | |
669a5db4 JG |
301 | } |
302 | ||
303 | static void via_set_piomode(struct ata_port *ap, struct ata_device *adev) | |
304 | { | |
305 | const struct via_isa_bridge *config = ap->host->private_data; | |
306 | int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1; | |
307 | int mode = config->flags & VIA_UDMA; | |
308 | static u8 tclock[5] = { 1, 1, 2, 3, 4 }; | |
309 | static u8 udma[5] = { 0, 33, 66, 100, 133 }; | |
310 | ||
311 | via_do_set_mode(ap, adev, adev->pio_mode, tclock[mode], set_ast, udma[mode]); | |
312 | } | |
313 | ||
314 | static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev) | |
315 | { | |
316 | const struct via_isa_bridge *config = ap->host->private_data; | |
317 | int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1; | |
318 | int mode = config->flags & VIA_UDMA; | |
319 | static u8 tclock[5] = { 1, 1, 2, 3, 4 }; | |
320 | static u8 udma[5] = { 0, 33, 66, 100, 133 }; | |
321 | ||
322 | via_do_set_mode(ap, adev, adev->dma_mode, tclock[mode], set_ast, udma[mode]); | |
323 | } | |
324 | ||
bfce5e01 | 325 | /** |
ff04715b | 326 | * via_tf_load - send taskfile registers to host controller |
bfce5e01 J |
327 | * @ap: Port to which output is sent |
328 | * @tf: ATA taskfile register set | |
329 | * | |
330 | * Outputs ATA taskfile to standard ATA host controller. | |
331 | * | |
332 | * Note: This is to fix the internal bug of via chipsets, which | |
ff04715b TH |
333 | * will reset the device register after changing the IEN bit on |
334 | * ctl register | |
bfce5e01 | 335 | */ |
ff04715b | 336 | static void via_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) |
bfce5e01 | 337 | { |
ff04715b | 338 | struct ata_taskfile tmp_tf; |
bfce5e01 | 339 | |
ff04715b TH |
340 | if (ap->ctl != ap->last_ctl && !(tf->flags & ATA_TFLAG_DEVICE)) { |
341 | tmp_tf = *tf; | |
342 | tmp_tf.flags |= ATA_TFLAG_DEVICE; | |
343 | tf = &tmp_tf; | |
bfce5e01 | 344 | } |
ff04715b | 345 | ata_sff_tf_load(ap, tf); |
bfce5e01 J |
346 | } |
347 | ||
669a5db4 | 348 | static struct scsi_host_template via_sht = { |
68d1d07b | 349 | ATA_BMDMA_SHT(DRV_NAME), |
669a5db4 JG |
350 | }; |
351 | ||
352 | static struct ata_port_operations via_port_ops = { | |
029cfd6b TH |
353 | .inherits = &ata_bmdma_port_ops, |
354 | .cable_detect = via_cable_detect, | |
669a5db4 JG |
355 | .set_piomode = via_set_piomode, |
356 | .set_dmamode = via_set_dmamode, | |
a1efdaba | 357 | .prereset = via_pre_reset, |
ff04715b | 358 | .sff_tf_load = via_tf_load, |
669a5db4 JG |
359 | }; |
360 | ||
361 | static struct ata_port_operations via_port_ops_noirq = { | |
029cfd6b | 362 | .inherits = &via_port_ops, |
5682ed33 | 363 | .sff_data_xfer = ata_sff_data_xfer_noirq, |
669a5db4 JG |
364 | }; |
365 | ||
627d2d32 A |
366 | /** |
367 | * via_config_fifo - set up the FIFO | |
368 | * @pdev: PCI device | |
369 | * @flags: configuration flags | |
370 | * | |
3a4fa0a2 | 371 | * Set the FIFO properties for this device if necessary. Used both on |
627d2d32 A |
372 | * set up and on and the resume path |
373 | */ | |
374 | ||
375 | static void via_config_fifo(struct pci_dev *pdev, unsigned int flags) | |
376 | { | |
377 | u8 enable; | |
f20b16ff | 378 | |
627d2d32 A |
379 | /* 0x40 low bits indicate enabled channels */ |
380 | pci_read_config_byte(pdev, 0x40 , &enable); | |
381 | enable &= 3; | |
f20b16ff | 382 | |
627d2d32 | 383 | if (flags & VIA_SET_FIFO) { |
73720861 | 384 | static const u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20}; |
627d2d32 A |
385 | u8 fifo; |
386 | ||
387 | pci_read_config_byte(pdev, 0x43, &fifo); | |
388 | ||
389 | /* Clear PREQ# until DDACK# for errata */ | |
390 | if (flags & VIA_BAD_PREQ) | |
391 | fifo &= 0x7F; | |
392 | else | |
393 | fifo &= 0x9f; | |
394 | /* Turn on FIFO for enabled channels */ | |
395 | fifo |= fifo_setting[enable]; | |
396 | pci_write_config_byte(pdev, 0x43, fifo); | |
397 | } | |
398 | } | |
399 | ||
669a5db4 JG |
400 | /** |
401 | * via_init_one - discovery callback | |
627d2d32 | 402 | * @pdev: PCI device |
669a5db4 JG |
403 | * @id: PCI table info |
404 | * | |
405 | * A VIA IDE interface has been discovered. Figure out what revision | |
406 | * and perform configuration work before handing it to the ATA layer | |
407 | */ | |
408 | ||
409 | static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id) | |
410 | { | |
411 | /* Early VIA without UDMA support */ | |
1626aeb8 | 412 | static const struct ata_port_info via_mwdma_info = { |
464cf177 | 413 | .flags = ATA_FLAG_SLAVE_POSS, |
669a5db4 JG |
414 | .pio_mask = 0x1f, |
415 | .mwdma_mask = 0x07, | |
416 | .port_ops = &via_port_ops | |
417 | }; | |
418 | /* Ditto with IRQ masking required */ | |
1626aeb8 | 419 | static const struct ata_port_info via_mwdma_info_borked = { |
464cf177 | 420 | .flags = ATA_FLAG_SLAVE_POSS, |
669a5db4 JG |
421 | .pio_mask = 0x1f, |
422 | .mwdma_mask = 0x07, | |
423 | .port_ops = &via_port_ops_noirq, | |
424 | }; | |
425 | /* VIA UDMA 33 devices (and borked 66) */ | |
1626aeb8 | 426 | static const struct ata_port_info via_udma33_info = { |
464cf177 | 427 | .flags = ATA_FLAG_SLAVE_POSS, |
669a5db4 JG |
428 | .pio_mask = 0x1f, |
429 | .mwdma_mask = 0x07, | |
bf6263a8 | 430 | .udma_mask = ATA_UDMA2, |
669a5db4 JG |
431 | .port_ops = &via_port_ops |
432 | }; | |
433 | /* VIA UDMA 66 devices */ | |
1626aeb8 | 434 | static const struct ata_port_info via_udma66_info = { |
464cf177 | 435 | .flags = ATA_FLAG_SLAVE_POSS, |
669a5db4 JG |
436 | .pio_mask = 0x1f, |
437 | .mwdma_mask = 0x07, | |
bf6263a8 | 438 | .udma_mask = ATA_UDMA4, |
669a5db4 JG |
439 | .port_ops = &via_port_ops |
440 | }; | |
441 | /* VIA UDMA 100 devices */ | |
1626aeb8 | 442 | static const struct ata_port_info via_udma100_info = { |
464cf177 | 443 | .flags = ATA_FLAG_SLAVE_POSS, |
669a5db4 JG |
444 | .pio_mask = 0x1f, |
445 | .mwdma_mask = 0x07, | |
bf6263a8 | 446 | .udma_mask = ATA_UDMA5, |
669a5db4 JG |
447 | .port_ops = &via_port_ops |
448 | }; | |
449 | /* UDMA133 with bad AST (All current 133) */ | |
1626aeb8 | 450 | static const struct ata_port_info via_udma133_info = { |
464cf177 | 451 | .flags = ATA_FLAG_SLAVE_POSS, |
669a5db4 JG |
452 | .pio_mask = 0x1f, |
453 | .mwdma_mask = 0x07, | |
bf6263a8 | 454 | .udma_mask = ATA_UDMA6, /* FIXME: should check north bridge */ |
669a5db4 JG |
455 | .port_ops = &via_port_ops |
456 | }; | |
887125e3 | 457 | const struct ata_port_info *ppi[] = { NULL, NULL }; |
669a5db4 JG |
458 | struct pci_dev *isa = NULL; |
459 | const struct via_isa_bridge *config; | |
460 | static int printed_version; | |
669a5db4 JG |
461 | u8 enable; |
462 | u32 timing; | |
f08048e9 | 463 | int rc; |
669a5db4 JG |
464 | |
465 | if (!printed_version++) | |
466 | dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); | |
467 | ||
f08048e9 TH |
468 | rc = pcim_enable_device(pdev); |
469 | if (rc) | |
470 | return rc; | |
471 | ||
669a5db4 JG |
472 | /* To find out how the IDE will behave and what features we |
473 | actually have to look at the bridge not the IDE controller */ | |
474 | for (config = via_isa_bridges; config->id; config++) | |
475 | if ((isa = pci_get_device(PCI_VENDOR_ID_VIA + | |
476 | !!(config->flags & VIA_BAD_ID), | |
477 | config->id, NULL))) { | |
478 | ||
44c10138 AK |
479 | if (isa->revision >= config->rev_min && |
480 | isa->revision <= config->rev_max) | |
669a5db4 JG |
481 | break; |
482 | pci_dev_put(isa); | |
483 | } | |
484 | ||
485 | if (!config->id) { | |
486 | printk(KERN_WARNING "via: Unknown VIA SouthBridge, disabling.\n"); | |
487 | return -ENODEV; | |
488 | } | |
489 | pci_dev_put(isa); | |
490 | ||
11f6400e AC |
491 | if (!(config->flags & VIA_NO_ENABLES)) { |
492 | /* 0x40 low bits indicate enabled channels */ | |
493 | pci_read_config_byte(pdev, 0x40 , &enable); | |
494 | enable &= 3; | |
495 | if (enable == 0) | |
496 | return -ENODEV; | |
669a5db4 JG |
497 | } |
498 | ||
499 | /* Initialise the FIFO for the enabled channels. */ | |
627d2d32 | 500 | via_config_fifo(pdev, config->flags); |
f20b16ff | 501 | |
669a5db4 JG |
502 | /* Clock set up */ |
503 | switch(config->flags & VIA_UDMA) { | |
504 | case VIA_UDMA_NONE: | |
505 | if (config->flags & VIA_NO_UNMASK) | |
887125e3 | 506 | ppi[0] = &via_mwdma_info_borked; |
669a5db4 | 507 | else |
887125e3 | 508 | ppi[0] = &via_mwdma_info; |
669a5db4 JG |
509 | break; |
510 | case VIA_UDMA_33: | |
887125e3 | 511 | ppi[0] = &via_udma33_info; |
669a5db4 JG |
512 | break; |
513 | case VIA_UDMA_66: | |
887125e3 | 514 | ppi[0] = &via_udma66_info; |
669a5db4 JG |
515 | /* The 66 MHz devices require we enable the clock */ |
516 | pci_read_config_dword(pdev, 0x50, &timing); | |
517 | timing |= 0x80008; | |
518 | pci_write_config_dword(pdev, 0x50, timing); | |
519 | break; | |
520 | case VIA_UDMA_100: | |
887125e3 | 521 | ppi[0] = &via_udma100_info; |
669a5db4 JG |
522 | break; |
523 | case VIA_UDMA_133: | |
887125e3 | 524 | ppi[0] = &via_udma133_info; |
669a5db4 JG |
525 | break; |
526 | default: | |
527 | WARN_ON(1); | |
528 | return -ENODEV; | |
529 | } | |
530 | ||
531 | if (config->flags & VIA_BAD_CLK66) { | |
532 | /* Disable the 66MHz clock on problem devices */ | |
533 | pci_read_config_dword(pdev, 0x50, &timing); | |
534 | timing &= ~0x80008; | |
535 | pci_write_config_dword(pdev, 0x50, timing); | |
536 | } | |
537 | ||
538 | /* We have established the device type, now fire it up */ | |
9363c382 | 539 | return ata_pci_sff_init_one(pdev, ppi, &via_sht, (void *)config); |
669a5db4 JG |
540 | } |
541 | ||
438ac6d5 | 542 | #ifdef CONFIG_PM |
627d2d32 A |
543 | /** |
544 | * via_reinit_one - reinit after resume | |
545 | * @pdev; PCI device | |
546 | * | |
547 | * Called when the VIA PATA device is resumed. We must then | |
548 | * reconfigure the fifo and other setup we may have altered. In | |
549 | * addition the kernel needs to have the resume methods on PCI | |
550 | * quirk supported. | |
551 | */ | |
552 | ||
553 | static int via_reinit_one(struct pci_dev *pdev) | |
554 | { | |
555 | u32 timing; | |
556 | struct ata_host *host = dev_get_drvdata(&pdev->dev); | |
557 | const struct via_isa_bridge *config = host->private_data; | |
f08048e9 TH |
558 | int rc; |
559 | ||
560 | rc = ata_pci_device_do_resume(pdev); | |
561 | if (rc) | |
562 | return rc; | |
f20b16ff | 563 | |
627d2d32 A |
564 | via_config_fifo(pdev, config->flags); |
565 | ||
566 | if ((config->flags & VIA_UDMA) == VIA_UDMA_66) { | |
567 | /* The 66 MHz devices require we enable the clock */ | |
568 | pci_read_config_dword(pdev, 0x50, &timing); | |
569 | timing |= 0x80008; | |
570 | pci_write_config_dword(pdev, 0x50, timing); | |
571 | } | |
572 | if (config->flags & VIA_BAD_CLK66) { | |
573 | /* Disable the 66MHz clock on problem devices */ | |
574 | pci_read_config_dword(pdev, 0x50, &timing); | |
575 | timing &= ~0x80008; | |
576 | pci_write_config_dword(pdev, 0x50, timing); | |
577 | } | |
f08048e9 TH |
578 | |
579 | ata_host_resume(host); | |
580 | return 0; | |
627d2d32 | 581 | } |
438ac6d5 | 582 | #endif |
627d2d32 | 583 | |
669a5db4 | 584 | static const struct pci_device_id via[] = { |
52df0ee0 JG |
585 | { PCI_VDEVICE(VIA, 0x0571), }, |
586 | { PCI_VDEVICE(VIA, 0x0581), }, | |
587 | { PCI_VDEVICE(VIA, 0x1571), }, | |
588 | { PCI_VDEVICE(VIA, 0x3164), }, | |
589 | { PCI_VDEVICE(VIA, 0x5324), }, | |
2d2744fc JG |
590 | |
591 | { }, | |
669a5db4 JG |
592 | }; |
593 | ||
594 | static struct pci_driver via_pci_driver = { | |
2d2744fc | 595 | .name = DRV_NAME, |
669a5db4 JG |
596 | .id_table = via, |
597 | .probe = via_init_one, | |
627d2d32 | 598 | .remove = ata_pci_remove_one, |
438ac6d5 | 599 | #ifdef CONFIG_PM |
627d2d32 A |
600 | .suspend = ata_pci_device_suspend, |
601 | .resume = via_reinit_one, | |
438ac6d5 | 602 | #endif |
669a5db4 JG |
603 | }; |
604 | ||
605 | static int __init via_init(void) | |
606 | { | |
607 | return pci_register_driver(&via_pci_driver); | |
608 | } | |
609 | ||
669a5db4 JG |
610 | static void __exit via_exit(void) |
611 | { | |
612 | pci_unregister_driver(&via_pci_driver); | |
613 | } | |
614 | ||
669a5db4 JG |
615 | MODULE_AUTHOR("Alan Cox"); |
616 | MODULE_DESCRIPTION("low-level driver for VIA PATA"); | |
617 | MODULE_LICENSE("GPL"); | |
618 | MODULE_DEVICE_TABLE(pci, via); | |
619 | MODULE_VERSION(DRV_VERSION); | |
620 | ||
621 | module_init(via_init); | |
622 | module_exit(via_exit); |