Commit | Line | Data |
---|---|---|
aaf9128a | 1 | // SPDX-License-Identifier: GPL-2.0 |
8a453cac PM |
2 | /* |
3 | * ALPHAPROJECT AP-SH4AD-0A Support. | |
4 | * | |
5 | * Copyright (C) 2010 ALPHAPROJECT Co.,Ltd. | |
6 | * Copyright (C) 2010 Matt Fleming | |
7 | * Copyright (C) 2010 Paul Mundt | |
8a453cac PM |
8 | */ |
9 | #include <linux/init.h> | |
10 | #include <linux/platform_device.h> | |
11 | #include <linux/io.h> | |
1f8eca12 GL |
12 | #include <linux/regulator/fixed.h> |
13 | #include <linux/regulator/machine.h> | |
8a453cac PM |
14 | #include <linux/smsc911x.h> |
15 | #include <linux/irq.h> | |
16 | #include <linux/clk.h> | |
17 | #include <asm/machvec.h> | |
18 | #include <asm/sizes.h> | |
19 | ||
1f8eca12 GL |
20 | /* Dummy supplies, where voltage doesn't matter */ |
21 | static struct regulator_consumer_supply dummy_supplies[] = { | |
22 | REGULATOR_SUPPLY("vddvario", "smsc911x"), | |
23 | REGULATOR_SUPPLY("vdd33a", "smsc911x"), | |
24 | }; | |
25 | ||
8a453cac PM |
26 | static struct resource smsc911x_resources[] = { |
27 | [0] = { | |
28 | .name = "smsc911x-memory", | |
29 | .start = 0xA4000000, | |
30 | .end = 0xA4000000 + SZ_256 - 1, | |
31 | .flags = IORESOURCE_MEM, | |
32 | }, | |
33 | [1] = { | |
34 | .name = "smsc911x-irq", | |
35 | .start = evt2irq(0x200), | |
36 | .end = evt2irq(0x200), | |
37 | .flags = IORESOURCE_IRQ, | |
38 | }, | |
39 | }; | |
40 | ||
41 | static struct smsc911x_platform_config smsc911x_config = { | |
42 | .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, | |
43 | .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, | |
44 | .flags = SMSC911X_USE_16BIT, | |
45 | .phy_interface = PHY_INTERFACE_MODE_MII, | |
46 | }; | |
47 | ||
48 | static struct platform_device smsc911x_device = { | |
49 | .name = "smsc911x", | |
50 | .id = -1, | |
51 | .num_resources = ARRAY_SIZE(smsc911x_resources), | |
52 | .resource = smsc911x_resources, | |
53 | .dev = { | |
54 | .platform_data = &smsc911x_config, | |
55 | }, | |
56 | }; | |
57 | ||
58 | static struct platform_device *apsh4ad0a_devices[] __initdata = { | |
59 | &smsc911x_device, | |
60 | }; | |
61 | ||
62 | static int __init apsh4ad0a_devices_setup(void) | |
63 | { | |
1f8eca12 GL |
64 | regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies)); |
65 | ||
8a453cac PM |
66 | return platform_add_devices(apsh4ad0a_devices, |
67 | ARRAY_SIZE(apsh4ad0a_devices)); | |
68 | } | |
69 | device_initcall(apsh4ad0a_devices_setup); | |
70 | ||
71 | static int apsh4ad0a_mode_pins(void) | |
72 | { | |
73 | int value = 0; | |
74 | ||
75 | /* These are the factory default settings of SW1 and SW2. | |
76 | * If you change these dip switches then you will need to | |
77 | * adjust the values below as well. | |
78 | */ | |
79 | value |= MODE_PIN0; /* Clock Mode 3 */ | |
80 | value |= MODE_PIN1; | |
81 | value &= ~MODE_PIN2; | |
82 | value &= ~MODE_PIN3; | |
83 | value &= ~MODE_PIN4; /* 16-bit Area0 bus width */ | |
84 | value |= MODE_PIN5; | |
85 | value |= MODE_PIN6; | |
86 | value |= MODE_PIN7; /* Normal mode */ | |
87 | value |= MODE_PIN8; /* Little Endian */ | |
88 | value |= MODE_PIN9; /* Crystal resonator */ | |
89 | value &= ~MODE_PIN10; /* 29-bit address mode */ | |
90 | value &= ~MODE_PIN11; /* PCI-E Root port */ | |
91 | value &= ~MODE_PIN12; /* 4 lane + 1 lane */ | |
92 | value |= MODE_PIN13; /* AUD Enable */ | |
93 | value &= ~MODE_PIN14; /* Normal Operation */ | |
94 | ||
95 | return value; | |
96 | } | |
97 | ||
98 | static int apsh4ad0a_clk_init(void) | |
99 | { | |
100 | struct clk *clk; | |
101 | int ret; | |
102 | ||
103 | clk = clk_get(NULL, "extal"); | |
7912825d | 104 | if (IS_ERR(clk)) |
8a453cac PM |
105 | return PTR_ERR(clk); |
106 | ret = clk_set_rate(clk, 33333000); | |
107 | clk_put(clk); | |
108 | ||
109 | return ret; | |
110 | } | |
111 | ||
112 | /* Initialize the board */ | |
113 | static void __init apsh4ad0a_setup(char **cmdline_p) | |
114 | { | |
115 | pr_info("Alpha Project AP-SH4AD-0A support:\n"); | |
116 | } | |
117 | ||
118 | static void __init apsh4ad0a_init_irq(void) | |
119 | { | |
120 | plat_irq_setup_pins(IRQ_MODE_IRQ3210); | |
121 | } | |
122 | ||
123 | /* | |
124 | * The Machine Vector | |
125 | */ | |
126 | static struct sh_machine_vector mv_apsh4ad0a __initmv = { | |
127 | .mv_name = "AP-SH4AD-0A", | |
128 | .mv_setup = apsh4ad0a_setup, | |
129 | .mv_mode_pins = apsh4ad0a_mode_pins, | |
130 | .mv_clk_init = apsh4ad0a_clk_init, | |
131 | .mv_init_irq = apsh4ad0a_init_irq, | |
132 | }; |