projects / linux-2.6-block.git / blame
| Commit | Line | Data |
|---|---|---|
| f16295e7 | 1 | /* |
| 96f1050d | 2 | * Do some checking to make sure things are OK |
| f16295e7 | 3 | * |
| 96f1050d | 4 | * Copyright 2007-2009 Analog Devices Inc. |
| f16295e7 | 5 | * |
| 96f1050d | 6 | * Licensed under the GPL-2 or later. |
| f16295e7 RG |
7 | */ |
| 8 | ||
| 13752046 | 9 | #include <asm/fixed_code.h> |
| 639f6571 BW |
10 | #include <mach/anomaly.h> |
| 11 | #include <asm/clocks.h> | |
| f16295e7 RG |
12 | |
| 13 | #ifdef CONFIG_BFIN_KERNEL_CLOCK | |
| 14 | ||
| 15 | # if (CONFIG_VCO_HZ > CONFIG_MAX_VCO_HZ) | |
| 16 | # error "VCO selected is more than maximum value. Please change the VCO multipler" | |
| 17 | # endif | |
| 18 | ||
| 19 | # if (CONFIG_SCLK_HZ > CONFIG_MAX_SCLK_HZ) | |
| 20 | # error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier" | |
| 21 | # endif | |
| 22 | ||
| 23 | # if (CONFIG_SCLK_HZ < CONFIG_MIN_SCLK_HZ) | |
| 24 | # error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier" | |
| 25 | # endif | |
| 26 | ||
| 27 | # if (ANOMALY_05000273) && (CONFIG_SCLK_HZ * 2 > CONFIG_CCLK_HZ) | |
| 28 | # error "ANOMALY 05000273, please make sure CCLK is at least 2x SCLK" | |
| 29 | # endif | |
| 30 | ||
| 31 | # if (CONFIG_SCLK_HZ > CONFIG_CCLK_HZ) && (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ) && (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ) | |
| 32 | # error "Please select sclk less than cclk" | |
| 33 | # endif | |
| 34 | ||
| 35 | #endif /* CONFIG_BFIN_KERNEL_CLOCK */ | |
| 13752046 MF |
36 | |
| 37 | #if CONFIG_BOOT_LOAD < FIXED_CODE_END | |
| 38 | # error "The kernel load address must be after the fixed code section" | |
| 39 | #endif | |
| 40 | ||
| 41 | #if (CONFIG_BOOT_LOAD & 0x3) | |
| 42 | # error "The kernel load address must be 4 byte aligned" | |
| 43 | #endif | |
| f7e989ab MF |
44 | |
| 45 | /* The entire kernel must be able to make a 24bit pcrel call to start of L1 */ | |
| 46 | #if ((0xffffffff - L1_CODE_START + 1) + CONFIG_BOOT_LOAD) > 0x1000000 | |
| 47 | # error "The kernel load address is too high; keep it below 10meg for safety" | |
| 48 | #endif | |
| 00049522 | 49 | |
| 357fd373 MF |
50 | #if ANOMALY_05000448 |
| 51 | # error You are using a part with anomaly 05000448, this issue causes random memory read/write failures - that means random crashes. | |
| 00049522 | 52 | #endif |
| 5ba76675 GY |
53 | |
| 54 | /* if 220 exists, can not set External Memory WB and L2 not_cached, either External Memory not_cached and L2 WB */ | |
| 55 | #if ANOMALY_05000220 && \ | |
| 41ba653f JZ |
56 | ((defined(CONFIG_BFIN_EXTMEM_WRITEBACK) && !defined(CONFIG_BFIN_L2_DCACHEABLE)) || \ |
| 57 | (!defined(CONFIG_BFIN_EXTMEM_DCACHEABLE) && defined(CONFIG_BFIN_L2_WRITEBACK))) | |
| 5ba76675 GY |
58 | # error You are exposing Anomaly 220 in this config, either config L2 as Write Through, or make External Memory WB. |
| 59 | #endif |